STM8S903K3T6CTR - 16MHz 8-Bit MCU, 8KB Flash | STMicroelectronics (Tape & Reel)
N.º de pieza: STM8S903K3T6CTR ✓ ActivoSTM8S903K3T6CTR Descripción general
An 8-bit microcontroller is a programmable semiconductor that executes instructions from embedded Flash memory and controls peripherals through dedicated input/output ports. The STM8S family uses an advanced Harvard-architecture core with an extended instruction set and a three-stage pipeline. This places the STM8S903K3 in the broader hierarchy of microcontroller, embedded processor, semiconductor, and electronic-control systems.
Principal features include 16 MHz maximum clock frequency, a 10-bit analog-to-digital converter, two timers, and serial connectivity covering UART, SPI, and I²C. The device also provides true EEPROM for parameters that must survive power removal. Its 2.95 V to 5.5 V operating range supports both conventional 3.3 V and 5 V embedded systems, while 16 I/O ports provide flexible connections to sensors, displays, actuators, and interface transceivers.
The STM8S903K3/F3 access-line architecture combines a compact control core with integrated communication peripherals. A three-stage pipeline supports efficient instruction execution, while the Harvard architecture separates program-memory access from data-memory access. Integrated EEPROM also avoids requiring an external nonvolatile memory device for small quantities of calibration, configuration, or serial-number data.
Typical applications include small industrial controllers, sensor nodes, appliance interfaces, compact instrumentation, communication modules, and low-cost embedded products. The 10-bit ADC supports analog measurement, the timers support timing and periodic-output tasks, and UART, SPI, and I²C permit connection to displays, sensors, memory devices, transceivers, and other digital peripherals without excessive external glue logic.
Designers should verify the exact peripheral mapping, alternate-function selection, clock configuration, and pin multiplexing in the manufacturer pin-description table before finalizing a PCB. Component values associated with the ADC, oscillator, reset, and power rails must follow the datasheet reference circuit, and unused pins should be configured to prevent unwanted inputs from increasing current consumption.
This product guide combines the manufacturer’s device description with application-oriented engineering guidance, a parameter comparison, and practical design notes. It also provides sourcing information for requesting a quotation through the XAIPART Request a Quote form, including current lead-time and availability confirmation.
Alternativas directas para STM8S903K3T6CTR — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con STM8S903K3T6CTR (mismo factor de forma y huella) — difiere en Core Architecture, Flash Program Memory, I/O Port Count, Package, Product Type.
STM8S003K3T6C
✅ Sustitución directaConsulte el precio
Ver hoja de datos →STM8S903K3T6CTR Valores máximos y características eléctricas
| Product Type | 8-bit microcontroller |
| Series | STM8S |
| Frecuencia de reloj máxima | 16 MHz |
| Flash Program Memory | Up to 8 KB |
| RAM | 1 KB |
| True Data EEPROM | 640 bytes |
| ADC Resolution | 10 bits |
| Timer Count | 2 |
| Serial Interfaces | UART, SPI, and I²C |
| I/O Port Count | 16 |
| Tensión de alimentación de funcionamiento | 2.95 V to 5.5 V |
| Core Architecture | Harvard architecture with 3-stage pipeline |
| Instruction Set | Extended instruction set |
| Encapsulado | 32-pin LQFP |
| Tipo de montaje | Surface mount |
| Estado del ciclo de vida | Active |
| RoHS Compliance | Compliant |
Configuración de pines de STM8S903K3T6CTR
| Pin 1 | VBAT — Backup supply input |
| Pin 2 | PC2 — General-purpose port C pin |
| Pin 3 | PC3 — General-purpose port C pin |
| Pin 4 | PC4 — General-purpose port C pin |
| Pin 5 | PC5 — General-purpose port C pin |
| Pin 6 | PC6 — General-purpose port C pin |
| Pin 7 | PC7 — General-purpose port C pin |
| Pin 8 | PD0 — General-purpose port D pin |
| Pin 9 | PD1 — General-purpose port D pin |
| Pin 10 | PD2 — General-purpose port D pin |
| Pin 11 | PD3 — General-purpose port D pin |
| Pin 12 | PD4 — General-purpose port D pin |
| Pin 13 | PD5 — General-purpose port D pin |
| Pin 14 | PD6 — General-purpose port D pin |
| Pin 15 | PD7 — General-purpose port D pin |
| Pin 16 | PB0 — General-purpose port B pin |
| Pin 17 | PB1 — General-purpose port B pin |
| Pin 18 | PB2 — General-purpose port B pin |
| Pin 19 | PB3 — General-purpose port B pin |
| Pin 20 | PB4 — General-purpose port B pin |
| Pin 21 | PB5 — General-purpose port B pin |
| Pin 22 | PB6 — General-purpose port B pin |
| Pin 23 | PB7 — General-purpose port B pin |
| Pin 24 | PA0 — General-purpose port A pin |
| Pin 25 | PA1 — General-purpose port A pin |
| Pin 26 | PA2 — General-purpose port A pin |
| Pin 27 | PA3 — General-purpose port A pin |
| Pin 28 | PA4 — General-purpose port A pin |
| Pin 29 | PA5 — General-purpose port A pin |
| Pin 30 | PA6 — General-purpose port A pin |
| Pin 31 | PA7 — General-purpose port A pin |
| Pin 32 | NRST — Reset input |
Aplicaciones típicas
STM8S903K3T6CTR es adecuado para 6 aplicacións: Industrial Sensor Node, Compact Appliance Controller, Serial Communication Module, Portable Measurement Instrument, LED Lighting Controller, Battery-Powered Embedded Device.
Industrial Sensor Node
The STM8S903K3T6CTR fits compact industrial sensor nodes that must measure an analog input and transmit data over a short serial link. Its 10-bit ADC supports moderate-resolution process or condition monitoring, while UART, SPI, and I²C provide options for connecting a transducer, local memory, or network transceiver. The 2.95 V to 5.5 V range supports both 3.3 V and 5 V system rails. Firmware can use the two timers for periodic sampling and communication timing, while the 640-byte EEPROM can retain calibration or configuration values. Designers should confirm the sensor’s input range and isolate noisy analog routing appropriately.
Recomendado
Compact Appliance Controller
The STM8S903K3T6CTR is suitable for compact appliance controls requiring multiple discrete inputs, outputs, and serial peripherals on a limited board area. Its 16 I/O ports can operate digital controls, indicator devices, and discrete sensors, while the timers support repeatable switching or timing functions. UART, SPI, and I²C allow connection to display or parameter-storage devices without a separate communications controller. The 8 KB Flash capacity is suitable for compact embedded applications, but code and bootloader growth must be tracked against the memory limit. Power-rail design should preserve stable operation across the full 2.95 V to 5.5 V input range.
Recomendado
Serial Communication Module
The STM8S903K3T6CTR can serve as the protocol controller in a small serial communication module because it integrates UART, SPI, and I²C in one 32-pin LQFP package. The 16 MHz core provides sufficient headroom for frame handling and protocol logic, and the two timers can support baud-rate generation, timeouts, or periodic status reporting. The true EEPROM can store configuration identifiers or communication parameters that must survive resets. Board design should reserve a programming interface and apply appropriate signal-integrity practices to external buses, especially when long traces or noisy surroundings are involved.
Recomendado
Portable Measurement Instrument
The STM8S903K3T6CTR is appropriate for a portable measurement instrument where a 10-bit ADC, local data storage, and modest processing requirements must coexist in a small controller. Flash holds firmware, RAM supports working buffers, and the 640-byte EEPROM can hold small calibration records. SPI can support a higher-capacity external data store when serial EEPROM is insufficient, while UART can report results to a host. The device’s 2.95 V minimum operating voltage accommodates common 3.3 V portable systems. Analog accuracy depends on the reference, sampling strategy, and layout, so those details should be verified against the application’s measurement requirements.
Recomendado
LED Lighting Controller
The STM8S903K3T6CTR can control compact LED lighting systems that require timed outputs, status indications, and configurable behavior. Its timers generate repeatable intervals for dimming sequences or blinking effects, while UART and I²C accept settings from a local controller or external module. The 640-byte EEPROM is useful for retaining lighting profiles or calibration constants, and the 16 I/O ports leave options for status LEDs and control signals. The MCU does not directly specify an LED-driver interface, so transistor stages, current limits, thermal design, and PWM-capable pin assignments must be designed separately and validated for the intended load.
Recomendado
Battery-Powered Embedded Device
The STM8S903K3T6CTR can serve as the central controller in a low-power embedded device using a 3.3 V battery-derived rail. Its compact LQFP package, integrated EEPROM, and on-chip communication peripherals reduce the number of external components. The timers can help organize periodic measurement and communication tasks, while the on-chip 10-bit ADC can monitor an analog condition. The 2.95 V to 5.5 V operating range provides compatibility with 3.3 V systems, although the complete power budget depends on the selected sleep modes, peripheral activity, and external load. Battery life must therefore be assessed using the manufacturer’s low-power characteristics and the final firmware duty cycle.
Recomendado
Datos de referencia de ingeniería para STM8S903K3T6CTR — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | STM8S003K3T6C |
|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics |
| Package | 32-pin LQFP | 32-pin LQFP |
Diferenciadores clave
- Integrated true data EEPROM (frente a STM8S003K3T6C)
- Documented communication peripheral set (frente a STM8S003K3T6C)
- Established 16 MHz performance target (frente a STM8S003K3T6C)
Notas de diseño
Route analog inputs away from digital clocks, SPI edges, UART signals, and switching-node traces. Keep the ADC source path short and use a stable ground reference for the measurement system. Where the analog signal is sensitive, ground the unused adjacent pins according to the manufacturer recommendations and evaluate the final board with the intended clock and peripheral configuration.
Design the power rail for the full 2.95 V to 5.5 V device range and place the required bypass capacitors close to the supply and ground pins. Decoupling values and ESR requirements should follow the manufacturer reference circuit. Verify startup behavior, maximum supply tolerance, and the voltage presented by any external peripheral before adding bulk or filtering capacitance.
Do not assume that every STM8 device with an LQFP package is a drop-in replacement. Alternate-function assignments, peripheral availability, interrupt vectors, clock setup, memory organization, and firmware can differ across the STM8S line. Before substituting STM8S003K3T6C for STM8S903K3T6CTR, compare the manufacturer pin tables and validate the complete board and firmware rather than relying on package dimensions alone.
Información de cumplimiento
RoHS-compliant status is reported in the component specifications. Other environmental, halogen-free, conflict-minerals, and automotive qualifications are not established by the available references.