SY89295UTG - 1024-Tap Programmable Delay Line | Microchip
N.º de pieza: SY89295UTG ✓ ActivoSY89295UTG Descripción general
A programmable delay line is a timing IC that delays a high-speed differential signal by a digitally selected interval. It belongs to the clock and timing IC hierarchy, where it provides deterministic signal-path timing rather than generating a clock. The SY89295UTG combines a 1-input, 32-tap-control architecture with fine delay resolution for circuit calibration, data capture, clock compensation, and communication-system timing.
The principal features are 1024 programmable taps, 10 ps delay granularity, and a maximum delay of 14.8 ns. Its LVPECL interface supports operation from either 2.5 V ±5% or 3.3 V ±10%, while the 7 mm × 7 mm TQFP package supports compact surface-mount designs. These specifications make fine delay calibration practical where fixed-delay elements cannot accommodate board-level timing variation.
Digital control permits the delay to be adjusted while the circuit is operating, supporting calibration and adaptive timing control. The input and output stages use LVPECL-compatible signaling, and the manufacturer describes the device as a precision programmable delay with fine-tune control. Designers must account for control-settling time, reference-clock quality, interconnect delay, and receiver setup and hold requirements when translating nominal delay into system timing accuracy.
Typical applications include high-speed test equipment, serial-interface deskew, clock recovery networks, data-acquisition systems, and telecommunications equipment. The part is particularly useful when a system must compensate for propagation-delay differences across cables, connectors, printed-circuit-board traces, or multiple acquisition channels without changing the physical layout.
Place input and output transmission lines with controlled impedance and minimize discontinuities on the high-speed LVPECL path. Use short, referenced ground-return connections and provide clean, decoupled supply rails because power and ground noise can disturb edge timing. The manufacturer’s pin-description and application information should be used when assigning the 32 package pins and terminating unused outputs.
This page combines the confirmed device parameters, package information, sourcing path, and same-family replacement analysis with practical implementation guidance. It is intended to help engineers determine whether the SY89295UTG provides the required delay range, interface standard, control method, and board footprint for precision timing designs.
Alternativas directas para SY89295UTG — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con SY89295UTG (mismo factor de forma y huella) — difiere en Package.
SY89295U
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
SY89295UTG Especificaciones
| Device Type | Programmable LVPECL delay line |
| Programmable Tap Count | 1024 taps |
| Minimum Delay | 3.2 ns |
| Maximum Delay | 14.8 ns |
| Delay Increment | 10 ps |
| Input Logic | LVPECL |
| Supply Voltage Option 1 | 2.5 V ±5% |
| Supply Voltage Option 2 | 3.3 V ±10% |
| Input Count | 1 input |
| Maximum Frequency | 1.5 GHz |
| Encapsulado | 32-pin TQFP, 7 mm × 7 mm |
| Tipo de montaje | Surface mount |
Guía de configuración de pines de SY89295UTG 32-pin tqfp, 7 mm × 7 mm
Configuración de pines para SY89295UTG (encapsulado 32-pin tqfp, 7 mm × 7 mm). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para SY89295UTG.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
SY89295UTG es adecuado para 6 aplicacións: High-Speed Clock Deskew, Data Acquisition Time Alignment, Telecommunications Clock Compensation, Precision Test and Measurement, Parallel Interface Skew Adjustment, Synchronous Communication Path Tuning.
High-Speed Clock Deskew
The SY89295UTG fits clock-deskew systems that require a differential timing path to be adjusted after board assembly. Its 1024 taps cover a 3.2 ns to 14.8 ns delay range, while 10 ps increments allow finer correction than a coarse programmable delay. Install the device in the LVPECL clock path, drive its digital control inputs from the timing controller, and reserve equal-length impedance-controlled routes for the differential clock. The useful system benefit is active compensation for trace, connector, and receiver variations, although the control path and clock distribution network must add less uncertainty than the correction being sought.
Recomendado
Data Acquisition Time Alignment
The SY89295UTG can align LVPECL clock or trigger paths in a multi-channel data-acquisition system. A maximum delay of 14.8 ns is useful for compensating cable, connector, and board-routing differences, and the 10 ps increment supports finer calibration than fixed delay elements. Place the device close to the affected clock receiver and keep its differential route impedance controlled. Its 1.5 GHz maximum frequency supports high-rate acquisition architectures, but the complete timing budget must include converter aperture, clock distribution skew, cable delay, and digital-control settling.
Recomendado
Telecommunications Clock Compensation
The SY89295UTG is appropriate for telecommunications equipment that must compensate variable propagation delay in an LVPECL clock or data path. Digital selection across 1024 taps provides a broad tuning range of 3.2 ns to 14.8 ns with 10 ps steps. Use it where field or manufacturing calibration can adjust timing without relocating a fixed-delay component. The implementation should include regulated 2.5 V or 3.3 V supplies, careful LVPECL termination, and short control traces to preserve command-to-delay accuracy across temperature and supply conditions.
Recomendado
Precision Test and Measurement
The SY89295UTG supports calibration and timing-alignment functions in precision test equipment. Its 10 ps programming increment can refine channel-to-channel alignment, while the 3.2 ns to 14.8 ns range covers common interconnect and fixture delays. The device operates with LVPECL at up to 1.5 GHz, making it useful beside high-speed sampling or clock-distribution circuitry. For best repeatability, place the delay line adjacent to the receiver, maintain consistent transmission-line geometry, and separate sensitive delay-control routing from noisy switching paths.
Recomendado
Parallel Interface Skew Adjustment
The SY89295UTG can compensate for fixed skew introduced by a high-speed parallel interface when the chosen signal can be routed through an LVPECL delay line. The adjustable range of up to 14.8 ns and 10 ps step size support board-level trimming after assembly. The design must account for input and output thresholds, reference-plane return paths, and any fixed delay already introduced by external components. Use the digital control interface to sweep the delay during calibration and store the required code for production testing.
Recomendado
Synchronous Communication Path Tuning
The SY89295UTG is useful in synchronous communication systems where a transmitter, receiver, or retimer must launch a clock or data signal with a calibrated phase offset. Its LVPECL interface, 1.5 GHz maximum frequency, and digitally controlled delay allow fine timing adjustment without changing cable length or board topology. Designers should preserve signal integrity with short differential routes, correct reference-plane grounding, and compliant termination. The programmable delay should be calibrated with the complete transmitter and receiver chain because device-to-device tolerance can otherwise make the nominal 10 ps command increment appear smaller.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para SY89295UTG — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | SY89295U |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 32-pin TQFP (7 mm × 7 mm) | 32-pin TQFP (7 mm × 7 mm) |
| Device Type | Programmable LVPECL delay line | Programmable LVPECL delay line |
| Programmable Tap Count | 1024 taps | 1024 taps |
| Delay Range | 3.2 ns to 14.8 ns | 3.2 ns to 14.8 ns |
| Delay Increment | 10 ps | 10 ps |
| Input Logic | LVPECL | LVPECL |
| Supply Voltage | 2.5 V ±5% or 3.3 V ±10% | 2.5 V ±5% or 3.3 V ±10% |
| Maximum Frequency | 1.5 GHz | 1.5 GHz |
Diferenciadores clave
- Fine digital delay adjustment (frente a SY89295U)
- Broad programmable range for interconnect compensation (frente a SY89295U)
- Compact 32-pin implementation (frente a SY89295U)
Notas de diseño
Treat the LVPECL input and output as controlled-impedance differential paths. Keep trace geometry consistent, maintain a continuous ground reference, and avoid stubs or abrupt layer changes that create reflections. LVPECL terminations and reference-circuit values should follow the manufacturer application guidance because incorrect biasing or return-path discontinuity can reduce edge quality even when the programmed delay is correct.
Place the SY89295UTG close to the clock receiver or timing-critical input, then connect the digital control interface with short, quiet traces. Keep switching-regulator and high-current return paths away from the delay-control pins. The 32-pin TQFP footprint requires careful escape routing because surrounding signal density can make it difficult to maintain consistent differential geometry at the device.
Do not equate the 10 ps programming increment with 10 ps end-to-end timing accuracy. Actual calibration includes input-to-output delay variation, control settling, reference-clock uncertainty, temperature, and supply sensitivity. Use the manufacturer test procedure to characterize the assembled circuit, and record the selected delay code for each channel during calibration.
Información de cumplimiento
The available product and distributor listings do not establish the complete compliance profile. Confirm RoHS, REACH, lead-free, halogen-free, AEC-Q100, and conflict-minerals status in the current Microchip documentation before qualification.