onsemi

TCA0372BDP1 - 1A Dual Power Op Amp 5-40V | onsemi

N.º de pieza: TCA0372BDP1 ✗ Fin de vida
5 V to 40 V Vdss 1.0 A per channel Id 8-PDIP, 8 pins Package
MOQ: 1 |

TCA0372BDP1 Descripción general

The onsemi TCA0372BDP1 is a dual power operational amplifier with two independent amplifier channels, a 5 V to 40 V supply range, and output-current capability up to 1 A per channel. The device is packaged in an 8-pin plastic dual in-line package designated 8-PDIP and is intended for power stages driving loads that exceed the current range of conventional operational amplifiers.

A power operational amplifier is an operational amplifier integrated with output-driver circuitry capable of supplying substantially higher load current. The TCA0372 family occupies the power-amplifier segment of the operational-amplifier hierarchy and is commonly positioned between general-purpose signal amplifiers and discrete transistor output stages. Its dual-channel architecture allows one package to drive two independent loads or to provide a complementary output arrangement when configured appropriately.

The main feature is high output-current capability of 1.0 A, allowing the amplifier to drive inductive, resistive, and capacitive loads more effectively than a conventional small-signal op amp. The 5 V to 40 V operating supply range supports higher-voltage systems than many low-voltage integrated amplifiers. According to the onsemi product page and manufacturer datasheet, the circuit is intended for servo amplifiers and power supplies, with no deadband crossover distortion intended to improve operation when driving coils.

Each channel contains an error amplifier followed by high-current output capability, allowing feedback to control the voltage delivered to the load. The power bipolar output stage can sink and source current, while external resistors and capacitors establish gain, bandwidth, stability, and output bias in the completed circuit. The high current capability does not remove the need to observe output-stage limits, load transients, supply decoupling, thermal conditions, and output-voltage headroom.

Typical uses include DC servo amplifiers, power-supply error amplifiers, audio and motor-control power stages, and industrial actuator drivers. The dual configuration can reduce component count in mirrored or dual-axis systems. For single-channel designs, one channel may remain unused, subject to the manufacturer's recommended input and output termination arrangements.

PCB layout should keep feedback routing short and place supply-bypass capacitors close to the device. Because output current can reach 1 A, copper width, connector sizing, thermal dissipation, and load-return paths become important. Designers should also use protection or snubber networks when switching highly reactive loads because feedback alone cannot absorb unlimited inductive energy.

This product page consolidates the confirmed electrical ratings, package information, sourcing structure, drop-in candidates, and application guidance for TCA0372BDP1. It also identifies which comparison details require verification against the manufacturer datasheet, helping engineers plan a controlled redesign and validation process rather than relying only on a generic amplifier substitution.

Alternativas directas para TCA0372BDP1 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con TCA0372BDP1 (mismo factor de forma y huella) — difiere en Crossover Distortion, Maximum Output Current.

onsemi
Crossover Distortion: No dead-band crossover distortion
Maximum Output Current: 1.0 A
Comparar con TCA0372BDP1 →

TCA0372DP1G

✅ Sustitución directa
onsemi
📦 8-PDIP
Dual monolithic power operational amplifier · 2 channels · 5 V to 40 V · 1.0 A · 1.4 MHz · 20 mV maximum · 90 dB nominal · No dead-band crossover distortion

Consulte el precio

Ver hoja de datos →

TCA0372BDP1G

✅ Sustitución directa
📦 8-PDIP
Same TCA0372B dual 1 A power-amplifier family and 8-PDIP format; extended-temperature suffix differs from DP1

📋 Alternativa de referencia (no en el catálogo)

TCA0372BDP1 Valores máximos y características eléctricas

Device Type Dual power operational amplifier
Number of Amplifier Channels 2 channels
Supply Voltage Range 5 V to 40 V
Corriente de salida máxima 1.0 A per channel
Configuración de salida Dual, single-ended operational-amplifier output
Encapsulado 8-PDIP, 8 pins
Tipo de montaje Through-hole
Recommended Primary Use Servo amplifiers and power supplies
Crossover Distortion No deadband crossover distortion

Guía de configuración de pines de TCA0372BDP1 8-pdip, 8 pins

Configuración de pines para TCA0372BDP1 (encapsulado 8-pdip, 8 pins). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.

Diagrama de patillaje del encapsulado 8-pdip, 8 pins para TCA0372BDP1

No hay datos detallados de patillaje disponibles para TCA0372BDP1.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

TCA0372BDP1 es adecuado para 6 aplicacións: DC Servo Amplifier, Industrial Actuator Driver, DC Power-Supply Error Amplifier, Audio Power Stage, Motor Control Power Driver, Precision Coil Current Regulation.

🏭

DC Servo Amplifier

The TCA0372BDP1 is well suited to a DC servo loop because its two channels each support output current up to 1.0 A, while the 5 V to 40 V supply range accommodates higher-voltage actuator systems. One channel can provide the high-current drive output and the other can perform a supporting function when the circuit requires independent error amplification. According to the onsemi manufacturer datasheet, servo amplifiers are a primary application for this monolithic dual power operational amplifier. In a practical position or speed loop, compensation capacitors and feedback resistors determine bandwidth and stability, so they should be calculated for the motor or actuator rather than copied without validation. The output stage must also remain within its voltage and current limits during startup, reversal, and stall conditions.

⚡

Industrial Actuator Driver

The TCA0372BDP1 can drive solenoid, proportional-valve, and other industrial actuator stages more directly than a conventional small-signal operational amplifier. Its 1.0 A output-current capability and 5 V to 40 V supply range are particularly useful when the actuator operates from a higher-voltage control bus. Feedback around the power stage lets the controller regulate actuator current or voltage, while the dual package can serve two related loads. Because inductive energy continues after the driver command changes, the completed circuit needs a suitable flyback clamp or snubber and return-current routing close to the device. Thermal checks should include worst-case continuous current rather than only nominal operating load.

🔋

DC Power-Supply Error Amplifier

The TCA0372BDP1 can serve as the high-current error amplifier in a power-supply control loop, delivering up to 1.0 A from a 5 V to 40 V operating supply. This capability is useful where the regulated output must source or sink substantial current and an external discrete output stage would otherwise be required. The onsemi manufacturer datasheet explicitly identifies power supplies among the intended applications. Its dual-channel configuration can support a primary output loop and an auxiliary regulation channel. Design work should verify loop compensation under minimum and maximum loading, account for the power amplifier's output saturation behavior, and include local supply bypassing close to the device. Fuse, current-limit, and reverse-protection stages should be designed independently.

🎧

Audio Power Stage

The TCA0372BDP1's dual high-current outputs and absence of deadband crossover distortion make it suitable for audio power-amplifier output stages, particularly where higher supply voltage permits greater signal swing. The two channels can support left and right outputs or a bridged mono arrangement, subject to the datasheet's output-voltage and thermal limits. The device also appears in discussions as a possible LM1877 replacement topic, although that alone does not prove package or pin compatibility. A successful audio implementation must consider output-filter stability, load impedance, crossover behavior, frequency response, and the DC offset at the speakers. Local decoupling and short, low-impedance power and ground paths are essential when several channels share the same supply rail.

🔧

Motor Control Power Driver

The TCA0372BDP1 can provide the high-current output stage of a closed-loop DC motor controller because each channel can supply up to 1.0 A and operate across a 5 V to 40 V supply range. The high-current capability simplifies direct drive of small motors and actuator coils compared with a conventional operational amplifier, while the second channel may support sensing or an auxiliary control function. The onsemi manufacturer datasheet describes the circuit as a power operational amplifier intended for servo amplifiers, reinforcing its suitability for electromechanical control. Commutation and protection circuitry must handle inductive transients, while current-sense feedback establishes torque or speed control. Validate heat dissipation during stall or blocked-rotor conditions because motor current can exceed the normal running load.

🧲

Precision Coil Current Regulation

The TCA0372BDP1 is appropriate for regulating current through a precision coil when the design needs an operational amplifier that can directly source and sink up to 1.0 A. The 5 V to 40 V operating range supports higher-voltage magnetic drivers, and the absence of deadband crossover distortion helps minimize command-dependent distortion in coil current. One amplifier channel can regulate the load while the other monitors or drives a complementary function. The loop should include a precision current-sense resistor or dedicated current-sense amplifier, with compensation selected for the coil's resistance, inductance, and the amplifier's bandwidth. Protection against disconnected loads and inductive overvoltage is required to prevent the output stage from being exposed to energy that was stored in the coil.

What is the TCA0372BDP1?
The TCA0372BDP1 is a dual power operational amplifier from onsemi designed to deliver output current up to 1.0 A per channel from a 5 V to 40 V supply. According to the onsemi product page and manufacturer datasheet, its two channels are intended for servo amplifiers and power supplies, and its output stage is designed to drive loads beyond the capability of conventional small-signal operational amplifiers.
What are the key specifications of TCA0372BDP1 that engineers should know?
The TCA0372BDP1 provides two operational-amplifier channels, a 5 V to 40 V supply range, and up to 1.0 A output current per channel in an 8-PDIP package. The onsemi manufacturer datasheet identifies it as a monolithic dual power amplifier for servo and power-supply applications, with no deadband crossover distortion intended to improve coil-driving performance.
What is the supply voltage range of TCA0372BDP1?
The TCA0372BDP1 operates from a 5 V minimum supply to a 40 V maximum supply. The onsemi manufacturer datasheet lists a 40 V maximum operating voltage for the device. Because the output stage can conduct 1.0 A, the supply system must also provide adequate transient-current capability and local decoupling rather than relying only on its nominal output voltage rating.
How much output current can TCA0372BDP1 deliver?
The TCA0372BDP1 can deliver up to 1.0 A of output current. According to the onsemi manufacturer datasheet, this high-current capability is the defining feature of the device and allows it to drive inductive and other power loads without adding a discrete transistor output stage. Actual continuous current should remain within the complete thermal and electrical operating limits.
Where can I download the TCA0372BDP1 datasheet PDF?
The official TCA0372BDP1 datasheet is available from onsemi at https://www.onsemi.com/pdf/datasheet/tca0372-d.pdf. It contains the authoritative electrical characteristics, ordering information, typical performance curves, application information, and package drawings. Use that document for the complete pin descriptions and operating limits when assigning PCB connections or designing around the 1 A output stage.
Where is the TCA0372BDP1 pinout located?
The TCA0372BDP1 pinout is located in the pin-configuration section of the onsemi manufacturer datasheet. The confirmed package is an 8-PDIP with two amplifier channels, supply connections, bias-related connections, and input or output functions assigned to the eight pins. Use the pin table and package drawing in that document when laying out the through-hole footprint.
Can TCA0372BDP1 drive a motor or relay coil?
Yes, TCA0372BDP1 is well suited to DC coil and servo-load drivers because it provides up to 1.0 A output current and no deadband crossover distortion. The onsemi product page specifically identifies servo amplifiers and power supplies as applications. Suitable flyback, clamp, or snubber protection must still be added when the load can produce abrupt inductive voltage spikes.
What is the difference between TCA0372BDP1 and TCA0372DP1G?
TCA0372DP1G is the same onsemi TCA0372 dual power-amplifier family offered with a distinct ordering suffix, while TCA0372BDP1 carries the B-designation and DP1 package and temperature-ordering code. Both are associated with the 5 V to 40 V, 1 A dual power-op-amp family. Confirm the exact suffix ratings and temperature limits in the onsemi ordering table before substitution.
Is TCA0372BDP1 suitable for a DC servo amplifier?
The TCA0372BDP1 is suitable for a DC servo amplifier because onsemi identifies servo amplifiers as a primary application and the device can deliver up to 1.0 A per channel. Its 5 V to 40 V supply range supports higher-voltage actuator systems. Compensation, current limiting, inductive suppression, and thermal margin must be designed around the specific motor or coil load.
When should I choose TCA0372BDP1 over a conventional operational amplifier?
Choose TCA0372BDP1 when the load current is too high for a conventional operational amplifier and an integrated power output stage is preferable to discrete transistors. Its two channels, 5 V to 40 V supply capability, and 1.0 A output rating simplify high-current servo and supply designs. Choose a conventional op amp instead when low noise, low power, or precision dominates and load current is modest.
What is the best drop-in replacement for TCA0372BDP1?
The closest documented drop-in candidate is onsemi TCA0372DP1G because the cross-reference comparison identifies it as the same TCA0372 dual power-op-amp family in an 8-PDIP configuration. Exact interchangeability still requires checking suffix-specific temperature, gain-bandwidth, and electrical-limit differences. No cross-brand replacement can be recommended as a true drop-in from the available manufacturer and comparison information.
Can TCA0372DP1G replace TCA0372BDP1?
TCA0372DP1G can be considered as a first-choice onsemi replacement candidate because it belongs to the same dual, 1 A TCA0372 power-amplifier family and is compared directly with TCA0372BDP1 as an 8-pin device. Before installation, verify the complete ordering table for operating-temperature grade, electrical characteristics, and any B-designation differences. PCB changes should not be required if the suffix comparison confirms the same pinout.
What can replace TCA0372BDP1?
Onsemi TCA0372DP1G is the leading replacement candidate identified for TCA0372BDP1 because both belong to the dual power-operational-amplifier family with an 8-PDIP format. TCA0372BDP1G is another family member that may fit, but suffix-specific limits must be checked. Confirm pin functions, supply limits, thermal ratings, and output-current conditions against the onsemi datasheet before production use.
Where can I buy TCA0372BDP1 and what is its price?
Use the Request a Quote form on this page to ask about TCA0372BDP1 availability, current unit cost, minimum order quantity, and lead time. The product is listed as an onsemi 8-PDIP dual power amplifier with a 5 V to 40 V supply range and 1 A output capability. A quote response provides the current commercial terms without embedding a potentially stale price.
Is TCA0372BDP1 in stock and what is its lead time?
Current stock and lead-time status for TCA0372BDP1 should be requested through the Request a Quote form on this page. The onsemi device is an 8-PDIP dual power operational amplifier rated for 5 V to 40 V operation and up to 1 A output current. Supply availability can vary by package suffix, so include the complete MPN and required quantity in the request.
Is TCA0372BDP1 the same as an LM1877 power amplifier?
TCA0372BDP1 is not established as a true pin-for-pin LM1877 substitute in the available information. An audio forum discussion identifies TCA0372 as an LM1877 replacement candidate, but that does not establish identical packages, pin functions, or safe electrical substitution. Compare the complete LM1877 and TCA0372 pinouts and thermal limits in their manufacturer documents before considering a board-level change.

Datos de referencia de ingeniería para TCA0372BDP1 — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose TCA0372BDP1 when the design requires two independent high-current amplifier channels, a 5 V to 40 V operating supply, and output current up to 1.0 A per channel. It is particularly appropriate for DC servo loops, actuator drivers, coil-current regulation, and power-supply error stages where a conventional operational amplifier would require a separate transistor output network. TCA0372DP1G is the closest documented onsemi drop-in candidate, but suffix-specific temperature and electrical differences must be checked before substitution. TCA0372BDP1G may be appropriate when the required ordering or temperature grade matches that variant. A cross-brand replacement should not be selected solely from family similarity; it must demonstrate the same 8-PDIP pinout, compatible supply range, equivalent current and thermal limits, and acceptable stability. For low-current precision or audio signal paths where a conventional low-noise amplifier is sufficient, the TCA0372BDP1 may add unnecessary power dissipation and cost.

Comparación con alternativas

Parámetro Este producto TCA0372DP1G TCA0372BDP1G
Brand onsemi onsemi onsemi
Package 8-PDIP 8-PDIP 8-PDIP
Device Type Dual power operational amplifier Dual power operational amplifier Dual power operational amplifier
Amplifier Channels 2 channels 2 channels 2 channels
Supply Voltage Range 5 V to 40 V 5 V to 40 V 5 V to 40 V
Maximum Output Current 1.0 A per channel 1.0 A per channel 1.0 A per channel
Primary Applications Servo amplifiers and power supplies Servo amplifiers and power supplies Servo amplifiers and power supplies
Crossover Distortion No deadband crossover distortion No deadband crossover distortion No deadband crossover distortion
Mounting Type Through-hole Through-hole Through-hole

Diferenciadores clave

  • Integrated high-current output capability (frente a Conventional small-signal operational amplifiers)
  • Dual power-amplifier channels in one package (frente a TCA0372DP1G)
  • High-voltage operating range (frente a Low-voltage signal operational amplifiers)
  • No deadband crossover distortion (frente a Power-output stages using biased transistor pairs with crossover gaps)

Notas de diseño

Estimated: at a 24 V supply, 12 V output, and 0.5 A load, the ideal output-stage dissipation is (24 V - 12 V) × 0.5 A = 6 W. Actual device dissipation also includes bias and internal losses, so the calculation is a conservative design starting point rather than a datasheet rating. Use the package thermal data and onsemi application guidance to select copper area, airflow, or a heat sink, and evaluate the highest expected continuous-load condition.

Place the input, feedback, and compensation networks close to the relevant amplifier pins, and keep high-current output paths away from low-level feedback traces. For a through-hole 8-PDIP, provide generous copper around the output and supply pins, use short supply-and-ground routes, and decouple the device near the package. The high-current stage requires low trace and connector resistance because a small milliohm of path resistance can create a meaningful voltage drop at 1 A.

Do not treat the 1 A rating as a universal continuous-load specification. Check output-current limits, output-voltage swing, supply limits, and thermal conditions for the selected suffix in the onsemi manufacturer datasheet. Add flyback or snubber protection for inductive loads, provide a defined state for unused amplifier channels, and verify that the compensation network remains stable across load, supply, and temperature extremes.

The 5 V to 40 V supply range does not eliminate the need for power-supply design. Local high-frequency bypassing should be placed at the device pins, while bulk capacitance must support load transients near the 1 A output limit. Check the source impedance across the complete operating frequency range, because an ideal 40 V rating alone does not guarantee stable operation with long supply wiring or inadequate decoupling.

Use a low-impedance power and ground architecture that serves both amplifier channels without sharing narrow neck-downs between the IC and the load return. Keep feedback components physically separate from the power stage where practical, especially in audio or precision control applications. Route test points to permit observation of input, output, and supply voltages without introducing accidental high-current paths or additional loop area.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The exact suffix-specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations are not stated in the available product information. Check the current onsemi product and quality documentation before making a compliance declaration.

Datos verificados el: 2026-11-16 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

TCA0372BDP1 datasheet TCA0372BDP1 pinout TCA0372BDP1 datasheet pdf TCA0372BDP1 equivalent TCA0372BDP1 replacement TCA0372BDP1 vs TCA0372DP1G TCA0372BDP1 1A power op amp TCA0372BDP1 5-40V amplifier TCA0372BDP1 8-PDIP footprint onsemi TCA0372BDP1 TCA0372BDP1 servo amplifier TCA0372BDP1 price TCA0372BDP1 stock TCA0372BDP1 application circuit

Componentes & términos relacionados

onsemi TCA0372BDP1 TCA0372DP1G TCA0372BDP1G TCA0372 LM1877 power operational amplifier operational amplifier power amplifier signal amplifier semiconductor dual amplifier 1 A output current 5 V to 40 V supply voltage output current supply voltage servo amplifier power-supply error amplifier inductive load coil driver motor control 8-PDIP DIP-8 through-hole package no deadband crossover distortion
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ