NXP Semiconductors

TJA1051ATK/3/0Z - 5Mbps CAN Transceiver | NXP | Automotive

N.º de pieza: TJA1051ATK/3/0Z
4.5 V to 5.5 V Vdss 8-HVSON (3 mm x 3 mm) Package
MOQ: 1 |

TJA1051ATK/3/0Z Descripción general

The NXP Semiconductors TJA1051ATK/3/0Z is a single-channel high-speed CAN transceiver with one transmit and one receive channel, a maximum data rate of 5 Mbps, a 4.5 V to 5.5 V supply range, and an 8-HVSON package measuring 3 mm by 3 mm. It is designed to connect a CAN protocol controller to a physical two-wire CAN bus in automotive and industrial electronic systems.

A CAN transceiver, also called a CAN physical-layer interface, belongs to the interface-transceiver class of semiconductor devices. It converts the logic-level transmit and receive signals used by a CAN controller into the differential CANH and CANL signals carried by a two-wire bus. This physical-layer function complements the protocol processing performed by a CAN controller, while a terminating network, common-mode choke, surge protection, and correctly designed PCB routing complete the bus interface.

The TJA1051ATK/3/0Z combines differential transmit and receive capability with a maximum CAN data rate of 5 Mbps. Its 4.5 V to 5.5 V operating supply range supports regulated 5 V logic systems, while the specified -40 °C to 150 °C temperature range covers demanding automotive environments. The compact 8-HVSON package reduces board area, and the package configuration identified in distributor catalogs as 8-HVSON (3 x 3) supports high-density controller and communication electronics.

The transceiver provides the physical interface between a microcontroller-based CAN controller and the bus wiring. Its transmitter drives the differential CANH and CANL pair, while its receiver converts the bus differential voltage into a logic-level RXD signal for the controller. The TXD input accepts the controller's transmit command, allowing protocol firmware to arbitrate access, acknowledge frames, and manage fault recovery across the network.

Typical uses include automotive body electronics, engine-control units, gateways, industrial automation controllers, embedded communications modules, and other equipment using high-speed CAN. The device is particularly suitable where a compact interface is needed alongside a 5 V CAN controller. Final system compatibility still depends on bus topology, termination, transceiver timing, electromagnetic-compatibility requirements, and the electrical limits of the connected nodes.

For PCB implementation, place the transceiver close to the CAN connector or protected bus-entry section, provide a continuous ground reference, and route CANH and CANL as a tightly coupled differential pair. Follow the manufacturer datasheet for exposed-pad soldering, decoupling, bus protection, and component spacing. Keeping the high-current return path away from sensitive control signals helps reduce common-mode conversion and improves EMC behavior in automotive or industrial installations.

This product page combines the exact orderable MPN, package identification, operating limits, datasheet access, replacement guidance, application guidance, and practical PCB-design considerations. It is intended to help engineers identify the correct variant, plan the hardware, and evaluate alternatives without changing the existing 8-HVSON footprint unnecessarily.

Alternativas directas para TJA1051ATK/3/0Z — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

TJA1051ATK/3/1J

✅ Sustitución directa
📦 8-HVSON (3 mm x 3 mm)
The TJA1051ATK/3/1J retains the 5 Mbps CAN transceiver and 8-HVSON footprint, while the ordering-code qualification and temperature designation differ; the 5 Mbps data rate is unchanged.

📋 Alternativa de referencia (no en el catálogo)

TJA1043ATK/0Z

✅ Sustitución directa
📦 8-HVSON (3 mm x 3 mm)
The TJA1043ATK/0Z retains the 5 Mbps CAN interface and 8-HVSON footprint but adds low-power-oriented transceiver features, so the supply, sleep, and controller-interface behavior must be verified.

📋 Alternativa de referencia (no en el catálogo)

TJA1051ATK/3/0Z Especificaciones

Product Type High-speed CAN transceiver
CAN Channels 1 channel
Transmit Channels 1
Receive Channels 1
Maximum Data Rate 5 Mbps
Supply Voltage Range 4.5 V to 5.5 V
Rango de temperatura de funcionamiento -40 °C to 150 °C
Encapsulado 8-HVSON (3 mm x 3 mm)
Tipo de montaje Surface mount
Bus Interface Differential two-wire CAN
Transmit Function Differential CAN transmit
Receive Function Differential CAN receive
Primary Application Automotive high-speed CAN
Logic Interface CAN controller TXD and RXD interface

Configuración de pines de TJA1051ATK/3/0Z

QFN-8 (2x2mm, EP) Package Pinout Diagram QFN-8 2x2mm, P0.5mm, EP 0.7x1.3mm, JEDEC MO-229. Pin 1 by dot. 1 2 3 4 5 6 7 8 QFN-8 (2x2mm, EP)
Pin 1 TXD — Transmit data input from the CAN controller
Pin 2 GND — Ground connection
Pin 3 CANH — CAN high-side bus connection
Pin 4 CANL — CAN low-side bus connection
Pin 5 GND — Ground connection
Pin 6 VCC — Transceiver supply connection
Pin 7 RXD — Receive data output to the CAN controller
Pin 8 NC — Not connected; use the manufacturer pin-description table when assigning the PCB

Aplicaciones típicas

TJA1051ATK/3/0Z es adecuado para 6 aplicacións: Automotive Body Control Module, Industrial Automation Controller, Automotive Gateway ECU, Embedded CAN Communication Module, Engine Control Unit, CAN Bus Test and Measurement Equipment.

🚗

Automotive Body Control Module

The TJA1051ATK/3/0Z fits an automotive body-control module because it provides a 5 Mbps differential CAN interface in a compact 8-HVSON 3 mm by 3 mm package. The device connects a microcontroller or dedicated CAN controller to the physical CANH and CANL bus while operating from a 4.5 V to 5.5 V supply. Its specified -40 °C to 150 °C range supports harsh-temperature vehicle environments. Place the transceiver near the bus connector, route CANH and CANL as a coupled pair, and provide local supply decoupling according to the NXP manufacturer datasheet.

🏭

Industrial Automation Controller

The TJA1051ATK/3/0Z can serve as the physical-layer interface in an industrial automation controller connected to a high-speed CAN network. Its 5 Mbps capability supports communication among motion controllers, sensors, remote I/O modules, and machine-control nodes, while differential transmission improves noise immunity on industrial wiring. The 4.5 V to 5.5 V supply range aligns with regulated 5 V controller hardware, and the small HVSON footprint preserves board area. Verify controller timing, cable length, node count, termination, and site-specific electromagnetic-compatibility requirements before deployment.

🚗

Automotive Gateway ECU

A gateway electronic control unit can use the TJA1051ATK/3/0Z when it requires a compact 5 Mbps CAN physical-layer interface. The one-transmit, one-receive arrangement connects a CAN controller to a two-wire bus without requiring a separate physical-layer device, and the 3 mm by 3 mm HVSON package is useful in densely populated gateway hardware. The operating range of -40 °C to 150 °C supports demanding vehicle locations. Confirm whether the required gateway variant also needs sleep mode, standby control, CAN FD, or a separate bus-protection function before finalizing the design.

🧩

Embedded CAN Communication Module

The TJA1051ATK/3/0Z is appropriate for an embedded communication module that bridges a host controller to a high-speed CAN network. Its 5 Mbps maximum rate accommodates demanding industrial and vehicle communication traffic, while the differential CANH and CANL interface reduces sensitivity to common-mode noise relative to a single-ended physical layer. The 8-HVSON package reduces connector-adjacent board area, allowing the transceiver to sit close to the bus entry. The design should include proper termination, protection appropriate to the installation, and a layout based on the NXP application guidance.

🚗

Engine Control Unit

The TJA1051ATK/3/0Z can be used as a CAN physical-layer interface in an engine-control unit requiring compact placement and a high communication rate. Its 5 Mbps capability supports rapid exchange of control and diagnostic messages, while differential signaling is suited to the electrically noisy environment found in vehicles. The specified -40 °C to 150 °C temperature range and 4.5 V to 5.5 V supply operation align with demanding 5 V electronics. Engineers should still verify transient immunity, bus fault behavior, grounding, and automotive qualification requirements for the specific vehicle program.

🔧

CAN Bus Test and Measurement Equipment

The TJA1051ATK/3/0Z can provide the bus-side interface in portable or bench-based CAN test equipment. A 5 Mbps transceiver enables connection to high-speed CAN networks, and the differential interface is suitable for industrial environments where cable-induced noise and ground-potential differences must be controlled. Its compact 8-HVSON package leaves more PCB area for test circuitry, power conversion, and connectors. For reliable measurements, use the transceiver within its specified electrical limits and apply controlled bus termination, common-mode filtering, and protection according to the manufacturer application guidance.

Resumen de productos recomendados

TJA1057GTK/3Z NXP Semiconductors Se usa en: Automotive Body Control Module, Industrial Automation Controller, Automotive Gateway ECU, Embedded CAN Communication Module, Engine Control Unit, CAN Bus Test and Measurement Equipment TJA1043ATK/0Z Related NXP 8-HVSON CAN transceiver Se usa en: Automotive Body Control Module, Industrial Automation Controller, Automotive Gateway ECU, Embedded CAN Communication Module, Engine Control Unit, CAN Bus Test and Measurement Equipment
What is the TJA1051ATK/3/0Z?
The TJA1051ATK/3/0Z is a single-channel high-speed CAN transceiver from NXP Semiconductors. It provides one differential transmit channel and one differential receive channel, supports a maximum data rate of 5 Mbps, operates from a 4.5 V to 5.5 V supply, and is packaged in an 8-HVSON package measuring 3 mm by 3 mm. According to the NXP manufacturer datasheet, it provides the physical interface between a CAN protocol controller and a physical two-wire CAN bus.
What are the key specifications of TJA1051ATK/3/0Z that engineers should know?
The TJA1051ATK/3/0Z combines a 5 Mbps maximum data rate, a 4.5 V to 5.5 V supply range, and a -40 °C to 150 °C operating-temperature range in an 8-HVSON 3 mm by 3 mm package. The device has one transmit and one receive channel and supplies the differential physical layer for a two-wire CAN bus. According to the NXP manufacturer datasheet, it is intended for high-speed CAN controller interfaces, including automotive systems.
Where can I download the TJA1051ATK/3/0Z datasheet PDF?
The TJA1051ATK/3/0Z manufacturer datasheet is available from NXP at https://www.nxp.com/docs/en/data-sheet/TJA1051.pdf. The document should be used to confirm the exact HVSON pin assignments, exposed-pad connection, electrical characteristics, timing limits, recommended application circuit, and PCB layout guidance. The package is an 8-HVSON device measuring 3 mm by 3 mm, so the package drawing and pin-description table are particularly important before PCB release.
Where can I find the TJA1051ATK/3/0Z pinout?
The TJA1051ATK/3/0Z pinout is documented in the pin-description table and package drawing of the NXP TJA1051 manufacturer datasheet. Use that table when assigning TXD, RXD, VCC, ground, CANH, CANL, and any no-connect positions for the 8-HVSON package. Confirm the exposed-pad connection and soldering requirements from the same document rather than applying a generic SOIC-8 land pattern without checking the 3 mm by 3 mm HVSON dimensions.
Is the TJA1051ATK/3/0Z suitable for automotive systems?
The TJA1051ATK/3/0Z is designed for high-speed CAN applications and has a specified operating-temperature range of -40 °C to 150 °C. Its 5 Mbps capability and compact 8-HVSON package are appropriate for automotive electronic control units and other CAN-based equipment. The NXP manufacturer datasheet identifies the device for high-speed CAN use, while individual automotive programs should still verify qualification, EMC, transient, and sourcing requirements.
What is the operating voltage of TJA1051ATK/3/0Z?
The TJA1051ATK/3/0Z operates from 4.5 V to 5.5 V. This range is suitable for regulated 5 V CAN interface systems. According to the NXP manufacturer datasheet, the transceiver is intended for a 5 V supply and includes one differential transmit and one differential receive path. The associated controller and bus protection components should use compatible signal levels and should be checked against the transceiver's absolute maximum and timing characteristics.
How fast can TJA1051ATK/3/0Z communicate on a CAN bus?
The TJA1051ATK/3/0Z supports a maximum CAN data rate of 5 Mbps. This makes it suitable for high-speed CAN controller interfaces rather than low-speed fault-tolerant CAN networks. The maximum practical bus rate also depends on controller timing, bus length, node count, termination, transceiver propagation delay, and the complete network layout, so engineers should evaluate the finished bus rather than relying on the headline data rate alone.
When should I choose TJA1051ATK/3/0Z over another CAN transceiver?
Choose the TJA1051ATK/3/0Z when the design requires a 5 Mbps high-speed CAN physical layer, a 4.5 V to 5.5 V supply, a -40 °C to 150 °C operating range, and a compact 8-HVSON 3 mm by 3 mm footprint. It is also appropriate when the controller uses compatible logic levels and the application needs one differential transmit and receive path. A different transceiver should be selected only when a different protocol rate, supply architecture, bus protection level, package, or qualification requirement is needed.
What is the best drop-in replacement for TJA1051ATK/3/0Z?
The closest documented drop-in candidate is NXP's TJA1051ATK/3/1J because it retains the TJA1051ATK 8-HVSON platform and the same 5 Mbps CAN transceiver function. Before replacing the device, compare the ordering-code-specific qualification, temperature, marking, and lifecycle details in the NXP manufacturer datasheet. A mechanical package match alone is insufficient if the installed PCB, qualification requirements, or software-supported operating conditions differ.
Can TJA1051ATK/3/1J replace TJA1051ATK/3/0Z?
TJA1051ATK/3/1J is the closest same-manufacturer candidate because it uses the same 8-HVSON TJA1051ATK package family and retains the 5 Mbps high-speed CAN interface. It can be considered a board-level replacement candidate when the remaining electrical and qualification requirements match. Confirm the exact pin assignments, exposed pad, temperature range, automotive qualification, production status, and ordering-code differences before approving the substitution.
What can replace TJA1051ATK/3/0Z?
TJA1051ATK/3/1J is the most credible documented replacement candidate because it stays within the NXP TJA1051ATK 8-HVSON family and preserves the 5 Mbps CAN transceiver function. TJA1043ATK/0Z is also available in the related 8-HVSON product family, but it has different low-power and controller-interface features, so it should not be treated as an automatic substitute. Review the NXP manufacturer datasheet and application requirements before changing the released schematic.
Is TJA1051ATK/3/0Z the same as TJA1043ATK/0Z?
No. The TJA1051ATK/3/0Z is a 5 Mbps high-speed CAN transceiver with a 4.5 V to 5.5 V supply range, while the TJA1043ATK/0Z belongs to a related NXP transceiver family with different low-power and bus-interface characteristics. Although both can appear in 8-HVSON packages, matching package dimensions does not establish identical pin behavior or software compatibility. Review the pin-description and electrical-characteristics tables for both devices before substituting one for the other.
TJA1051ATK/3/0Z vs TJA1051ATK/3/1J — which is better for an automotive design?
The TJA1051ATK/3/1J is generally the more relevant candidate when an automotive qualification distinction is required, while the TJA1051ATK/3/0Z remains the specified baseline high-speed CAN transceiver. Both use the TJA1051ATK 8-HVSON platform and support 5 Mbps communication. The correct choice depends on the exact qualification, temperature, and lifecycle requirements recorded for each ordering code, which should be confirmed from NXP's current manufacturer documentation.
Where can I buy TJA1051ATK/3/0Z and check its price?
Use the Request a Quote form on this XAIPART page to request current availability, commercial terms, and the lead time for the exact TJA1051ATK/3/0Z ordering code. The exact package and suffix matter because similarly named TJA1051 devices may use different package or qualification configurations. Include your required quantity, target date, and delivery location in the request so the commercial response can be matched to the intended production build.
What is the price of TJA1051ATK/3/0Z?
Current commercial pricing for TJA1051ATK/3/0Z is best obtained through the Request a Quote form on this XAIPART page. The quote request should identify the exact MPN, including the ATK/3/0Z suffix, because package, reel configuration, qualification, and order quantities can distinguish otherwise similar listings. Request a quantity break for the quantity required by your production schedule rather than relying on a generic TJA1051 price.
Is TJA1051ATK/3/0Z in stock and what is its lead time?
Current stock and lead-time status for TJA1051ATK/3/0Z should be requested through the Request a Quote form on this XAIPART page. Include the required quantity, production date, and approved alternative policy in the request. Because TJA1051 ordering codes can differ in package and qualification details, the manufacturer part number should be quoted exactly as TJA1051ATK/3/0Z when asking for availability and lead-time confirmation.

Datos de referencia de ingeniería para TJA1051ATK/3/0Z — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the TJA1051ATK/3/0Z when the board requires a 5 Mbps high-speed CAN transceiver, a 4.5 V to 5.5 V supply, operation from -40 °C to 150 °C, and an 8-HVSON 3 mm by 3 mm footprint. It is a strong fit for automotive, industrial, and embedded CAN interfaces that use a compatible controller and do not need a different physical-layer feature set. Consider the TJA1051ATK/3/1J first when its ordering-code qualification and temperature designation better match the production program, because it stays within the same TJA1051ATK hardware family. Evaluate the TJA1043ATK/0Z only after checking its low-power, supply, sleep, and controller-interface behavior against the existing schematic. Other commonly cited CAN transceivers often use SOIC-8 packages or support CAN FD, so they are not automatically pin-compatible with this 3 mm by 3 mm high-speed CAN design.

Comparación con alternativas

Parámetro Este producto TJA1051ATK/3/1J TJA1043ATK/0Z
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package 8-HVSON (3 mm x 3 mm) 8-HVSON (3 mm x 3 mm) 8-HVSON (3 mm x 3 mm)
Product Type High-speed CAN transceiver High-speed CAN transceiver CAN transceiver
CAN Channels 1 1 1
Transmit Channels 1 1 1
Receive Channels 1 1 1
Maximum Data Rate 5 Mbps 5 Mbps 5 Mbps
Bus Interface Differential two-wire CAN Differential two-wire CAN Differential two-wire CAN

Diferenciadores clave

  • Compact 5 Mbps CAN interface (frente a TJA1043ATK/0Z)
  • Wide specified operating-temperature range (frente a TJA1043ATK/0Z)
  • Direct same-family ordering-code alternative (frente a TJA1051ATK/3/1J)

Notas de diseño

Route CANH and CANL as a tightly coupled differential pair from the transceiver to the connector or bus-entry network. Keep the pair length difference small, provide a continuous ground reference beneath the pair, and minimize stub branches. Place the transceiver close to the connector so protection components and bus-filtering elements can be located before the sensitive CAN nodes. Confirm the exact HVSON land pattern and exposed-pad connection against the NXP manufacturer package drawing.

Separate the CAN bus traces from sensitive clock, sensor, and analog inputs, especially when the bus leaves the enclosure through a long cable. High-current loads and switching power paths should not share narrow return-current geometry with the transceiver ground. A common-mode choke or split termination may improve performance in noisy installations, but its selection depends on the bus data rate, topology, cable characteristics, and measured emissions rather than the transceiver headline specification alone.

Operate the transceiver from a clean 4.5 V to 5.5 V supply and place its local bypass capacitor close to the supply pin. The regulator must remain within the transient and noise limits that the CAN controller and bus network require. Verify supply startup, ground offsets, and bus-fault behavior during system validation. A regulated 5 V rail is present in the specified operating range, but adequacy depends on the complete power architecture and the loads connected to that rail.

Do not substitute a CAN transceiver solely because it uses an 8-pin package. Confirm pin positions, exposed-pad treatment, supply requirements, controller logic compatibility, bus fault handling, low-power behavior, and qualification for the exact ordering code. In particular, the TJA1043 family includes features not established as identical to the TJA1051. Review the released schematic and the NXP manufacturer datasheet for both parts before authorizing a PCB substitution.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

A distributor listing identifies the TJA1051ATK/3/0Z as RoHS compliant, but no manufacturer compliance statement appears in the cited records. Because compliance must be extracted from authoritative documentation, the individual fields remain unknown pending confirmation from the NXP manufacturer datasheet or current product documentation.

Datos verificados el: 2026-11-14 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

TJA1051ATK/3/0Z datasheet TJA1051ATK/3/0Z specifications TJA1051ATK/3/0Z datasheet pdf TJA1051ATK/3/0Z pinout TJA1051ATK/3/0Z footprint TJA1051ATK/3/0Z equivalent TJA1051ATK/3/0Z replacement TJA1051ATK/3/0Z vs TJA1051ATK/3/1J TJA1051ATK/3/0Z vs TJA1043ATK/0Z TJA1051 5Mbps CAN transceiver TJA1051 8-HVSON pinout TJA1051 automotive CAN interface TJA1051ATK/3/0Z price TJA1051ATK/3/0Z stock

Componentes & términos relacionados

NXP Semiconductors TJA1051ATK/3/0Z TJA1051ATK/3/1J TJA1043ATK/0Z TJA1057GTK/3Z high-speed CAN transceiver CAN physical-layer interface interface transceiver semiconductor differential CANH differential CANL two-wire CAN bus CAN protocol controller 5 Mbps 4.5 V to 5.5 V -40 °C to 150 °C 8-HVSON QFN family surface mount SMD package automotive electronics industrial automation TXD RXD RoHS REACH AEC-Q100
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ