TJA1051ATK/3/0Z - 5Mbps CAN Transceiver | NXP | Automotive
MPN: TJA1051ATK/3/0ZTJA1051ATK/3/0Z Tóm tắt
A CAN transceiver, also called a CAN physical-layer interface, belongs to the interface-transceiver class of semiconductor devices. It converts the logic-level transmit and receive signals used by a CAN controller into the differential CANH and CANL signals carried by a two-wire bus. This physical-layer function complements the protocol processing performed by a CAN controller, while a terminating network, common-mode choke, surge protection, and correctly designed PCB routing complete the bus interface.
The TJA1051ATK/3/0Z combines differential transmit and receive capability with a maximum CAN data rate of 5 Mbps. Its 4.5 V to 5.5 V operating supply range supports regulated 5 V logic systems, while the specified -40 °C to 150 °C temperature range covers demanding automotive environments. The compact 8-HVSON package reduces board area, and the package configuration identified in distributor catalogs as 8-HVSON (3 x 3) supports high-density controller and communication electronics.
The transceiver provides the physical interface between a microcontroller-based CAN controller and the bus wiring. Its transmitter drives the differential CANH and CANL pair, while its receiver converts the bus differential voltage into a logic-level RXD signal for the controller. The TXD input accepts the controller's transmit command, allowing protocol firmware to arbitrate access, acknowledge frames, and manage fault recovery across the network.
Typical uses include automotive body electronics, engine-control units, gateways, industrial automation controllers, embedded communications modules, and other equipment using high-speed CAN. The device is particularly suitable where a compact interface is needed alongside a 5 V CAN controller. Final system compatibility still depends on bus topology, termination, transceiver timing, electromagnetic-compatibility requirements, and the electrical limits of the connected nodes.
For PCB implementation, place the transceiver close to the CAN connector or protected bus-entry section, provide a continuous ground reference, and route CANH and CANL as a tightly coupled differential pair. Follow the manufacturer datasheet for exposed-pad soldering, decoupling, bus protection, and component spacing. Keeping the high-current return path away from sensitive control signals helps reduce common-mode conversion and improves EMC behavior in automotive or industrial installations.
This product page combines the exact orderable MPN, package identification, operating limits, datasheet access, replacement guidance, application guidance, and practical PCB-design considerations. It is intended to help engineers identify the correct variant, plan the hardware, and evaluate alternatives without changing the existing 8-HVSON footprint unnecessarily.
Bộ thay thế dễ dàng lắp đặt cho TJA1051ATK/3/0Z — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
TJA1051ATK/3/1J
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TJA1043ATK/0Z
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TJA1051ATK/3/0Z Thông số kỹ thuật
| Product Type | High-speed CAN transceiver |
| CAN Channels | 1 channel |
| Transmit Channels | 1 |
| Receive Channels | 1 |
| Maximum Data Rate | 5 Mbps |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Khoảng nhiệt độ hoạt động | -40 °C to 150 °C |
| Hộp | 8-HVSON (3 mm x 3 mm) |
| Kiểu lắp đặt | Surface mount |
| Bus Interface | Differential two-wire CAN |
| Transmit Function | Differential CAN transmit |
| Receive Function | Differential CAN receive |
| Primary Application | Automotive high-speed CAN |
| Logic Interface | CAN controller TXD and RXD interface |
Cấu hình chân TJA1051ATK/3/0Z
| Chân 1 | TXD — Transmit data input from the CAN controller |
| Chân 2 | GND — Ground connection |
| Chân 3 | CANH — CAN high-side bus connection |
| Chân 4 | CANL — CAN low-side bus connection |
| Chân 5 | GND — Ground connection |
| Chân 6 | VCC — Transceiver supply connection |
| Chân 7 | RXD — Receive data output to the CAN controller |
| Chân 8 | NC — Not connected; use the manufacturer pin-description table when assigning the PCB |
Ứng dụng tiêu biểu
TJA1051ATK/3/0Z phù hợp cho 6 Áp dụngs: Automotive Body Control Module, Industrial Automation Controller, Automotive Gateway ECU, Embedded CAN Communication Module, Engine Control Unit, CAN Bus Test and Measurement Equipment.
Automotive Body Control Module
The TJA1051ATK/3/0Z fits an automotive body-control module because it provides a 5 Mbps differential CAN interface in a compact 8-HVSON 3 mm by 3 mm package. The device connects a microcontroller or dedicated CAN controller to the physical CANH and CANL bus while operating from a 4.5 V to 5.5 V supply. Its specified -40 °C to 150 °C range supports harsh-temperature vehicle environments. Place the transceiver near the bus connector, route CANH and CANL as a coupled pair, and provide local supply decoupling according to the NXP manufacturer datasheet.
Được đề xuất
Industrial Automation Controller
The TJA1051ATK/3/0Z can serve as the physical-layer interface in an industrial automation controller connected to a high-speed CAN network. Its 5 Mbps capability supports communication among motion controllers, sensors, remote I/O modules, and machine-control nodes, while differential transmission improves noise immunity on industrial wiring. The 4.5 V to 5.5 V supply range aligns with regulated 5 V controller hardware, and the small HVSON footprint preserves board area. Verify controller timing, cable length, node count, termination, and site-specific electromagnetic-compatibility requirements before deployment.
Được đề xuất
Automotive Gateway ECU
A gateway electronic control unit can use the TJA1051ATK/3/0Z when it requires a compact 5 Mbps CAN physical-layer interface. The one-transmit, one-receive arrangement connects a CAN controller to a two-wire bus without requiring a separate physical-layer device, and the 3 mm by 3 mm HVSON package is useful in densely populated gateway hardware. The operating range of -40 °C to 150 °C supports demanding vehicle locations. Confirm whether the required gateway variant also needs sleep mode, standby control, CAN FD, or a separate bus-protection function before finalizing the design.
Được đề xuất
Embedded CAN Communication Module
The TJA1051ATK/3/0Z is appropriate for an embedded communication module that bridges a host controller to a high-speed CAN network. Its 5 Mbps maximum rate accommodates demanding industrial and vehicle communication traffic, while the differential CANH and CANL interface reduces sensitivity to common-mode noise relative to a single-ended physical layer. The 8-HVSON package reduces connector-adjacent board area, allowing the transceiver to sit close to the bus entry. The design should include proper termination, protection appropriate to the installation, and a layout based on the NXP application guidance.
Được đề xuất
Engine Control Unit
The TJA1051ATK/3/0Z can be used as a CAN physical-layer interface in an engine-control unit requiring compact placement and a high communication rate. Its 5 Mbps capability supports rapid exchange of control and diagnostic messages, while differential signaling is suited to the electrically noisy environment found in vehicles. The specified -40 °C to 150 °C temperature range and 4.5 V to 5.5 V supply operation align with demanding 5 V electronics. Engineers should still verify transient immunity, bus fault behavior, grounding, and automotive qualification requirements for the specific vehicle program.
Được đề xuất
CAN Bus Test and Measurement Equipment
The TJA1051ATK/3/0Z can provide the bus-side interface in portable or bench-based CAN test equipment. A 5 Mbps transceiver enables connection to high-speed CAN networks, and the differential interface is suitable for industrial environments where cable-induced noise and ground-potential differences must be controlled. Its compact 8-HVSON package leaves more PCB area for test circuitry, power conversion, and connectors. For reliable measurements, use the transceiver within its specified electrical limits and apply controlled bus termination, common-mode filtering, and protection according to the manufacturer application guidance.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TJA1051ATK/3/0Z — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TJA1051ATK/3/1J | TJA1043ATK/0Z |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 8-HVSON (3 mm x 3 mm) | 8-HVSON (3 mm x 3 mm) | 8-HVSON (3 mm x 3 mm) |
| Product Type | High-speed CAN transceiver | High-speed CAN transceiver | CAN transceiver |
| CAN Channels | 1 | 1 | 1 |
| Transmit Channels | 1 | 1 | 1 |
| Receive Channels | 1 | 1 | 1 |
| Maximum Data Rate | 5 Mbps | 5 Mbps | 5 Mbps |
| Bus Interface | Differential two-wire CAN | Differential two-wire CAN | Differential two-wire CAN |
Bảo phân biệt quan trọng
- Compact 5 Mbps CAN interface (vsTJA1043ATK/0Z)
- Wide specified operating-temperature range (vsTJA1043ATK/0Z)
- Direct same-family ordering-code alternative (vsTJA1051ATK/3/1J)
Ghi chú thiết kế
Route CANH and CANL as a tightly coupled differential pair from the transceiver to the connector or bus-entry network. Keep the pair length difference small, provide a continuous ground reference beneath the pair, and minimize stub branches. Place the transceiver close to the connector so protection components and bus-filtering elements can be located before the sensitive CAN nodes. Confirm the exact HVSON land pattern and exposed-pad connection against the NXP manufacturer package drawing.
Separate the CAN bus traces from sensitive clock, sensor, and analog inputs, especially when the bus leaves the enclosure through a long cable. High-current loads and switching power paths should not share narrow return-current geometry with the transceiver ground. A common-mode choke or split termination may improve performance in noisy installations, but its selection depends on the bus data rate, topology, cable characteristics, and measured emissions rather than the transceiver headline specification alone.
Operate the transceiver from a clean 4.5 V to 5.5 V supply and place its local bypass capacitor close to the supply pin. The regulator must remain within the transient and noise limits that the CAN controller and bus network require. Verify supply startup, ground offsets, and bus-fault behavior during system validation. A regulated 5 V rail is present in the specified operating range, but adequacy depends on the complete power architecture and the loads connected to that rail.
Do not substitute a CAN transceiver solely because it uses an 8-pin package. Confirm pin positions, exposed-pad treatment, supply requirements, controller logic compatibility, bus fault handling, low-power behavior, and qualification for the exact ordering code. In particular, the TJA1043 family includes features not established as identical to the TJA1051. Review the released schematic and the NXP manufacturer datasheet for both parts before authorizing a PCB substitution.
Thông tin tuân thủ
A distributor listing identifies the TJA1051ATK/3/0Z as RoHS compliant, but no manufacturer compliance statement appears in the cited records. Because compliance must be extracted from authoritative documentation, the individual fields remain unknown pending confirmation from the NXP manufacturer datasheet or current product documentation.