NXP Semiconductors

TJA1054T/N1 - Fault-Tolerant 125 kBd CAN | NXP

N.º de pieza: TJA1054T/N1 ✓ Activo
14-pin SOIC, 3.9 mm body Package Very low EME from CANH and CANL output matching Memory
MOQ: 1 |

TJA1054T/N1 Descripción general

The NXP Semiconductors TJA1054T/N1 is a fault-tolerant Controller Area Network transceiver designed for low-speed CAN communication up to 125 kBd in passenger-car applications. It provides the physical-layer interface between a CAN protocol controller and the CANH and CANL bus conductors, and the device is packaged in an 14-pin small-outline SOIC package. Its fault-tolerant architecture is intended for communication links where reliable operation during bus faults is important.

A CAN transceiver is an interface IC within the wider network-interface and semiconductor hierarchy. It converts logic-level transmit and receive signals from a CAN controller into the physical differential signaling used on a CAN bus. CAN itself is a deterministic, multiplexed communication network used in automotive and industrial control systems. The TJA1054T/N1 occupies the physical-layer position between digital processing circuitry and the two-wire bus.

The TJA1054T/N1 is identified as a fault-tolerant CAN transceiver and is primarily intended for low-speed networks operating at up to 125 kBd. NXP states that the device is pin-compatible and downwards-compatible with the PCA82C252T and TJA1053T, allowing either device to be replaced while retaining the existing functions. This compatibility makes the TJA1054T a practical upgrade path for designs already using those interface devices.

The principal engineering benefit is bus-fault tolerance. NXP describes very low electromagnetic emission as an important improvement over the PCA82C252 and TJA1053T, based on strong matching between the CANH and CANL outputs. Good matching helps limit differential-mode emissions and improves signal quality on the physical bus. The TJA1054 family also retains the functional structure expected by existing CAN controllers, allowing a PCB-level replacement without changing the surrounding bus interface.

Typical uses include passenger-car body and comfort networks, low-speed automotive CAN subnets, sensor and actuator gateways, and industrial equipment that retains an automotive CAN architecture. In these systems, the transceiver connects a CAN controller to CANH and CANL, provides bus-side transmit and receive functions, and helps the network continue operating correctly when the bus is shorted to ground, shorted to supply, or open. Exact protection and operating details should be confirmed in the manufacturer datasheet.

PCB implementation should preserve the device's pin compatibility with the PCA82C252T and TJA1053T, including the same 14-pin SOIC footprint and signal assignments. Check the bus-polarity, supply, ground, transceiver-mode, and controller-interface connections against the NXP pin description before fabrication. Do not assume that all CAN transceivers are interchangeable merely because they use the same protocol; interface voltage, mode-control logic, and fault behavior must also match.

This product page combines the manufacturer compatibility information, package identification, available ordering references, and practical replacement guidance in one engineering-focused record. It also distinguishes verified drop-in choices from options that require package or function review, helping engineers evaluate a CAN bus update without relying on an incomplete cross-reference list.

Alternativas directas para TJA1054T/N1 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

TJA1054AT

✅ Sustitución directa
NXP Semiconductors
📦 14-pin SOIC
Fault-tolerant single-wire CAN transceiver · NXP Semiconductors · 125 kBd · Single-wire CAN · Protocol controller to physical bus-wire interface · ElectroStatic Discharge improved version of TJA1054 · Fault-tolerant CAN operation · SO14, 14 pins

Consulte el precio

Ver hoja de datos →

TJA1054T/VM,512

✅ Sustitución directa
📦 14-pin SOIC
Same TJA1054T family, 125 kBd fault-tolerant CAN function, and 14-pin SOIC footprint; ordering qualification differs, with a 0% core data-rate difference.

📋 Alternativa de referencia (no en el catálogo)

TJA1053T

✅ Sustitución directa
📦 14-pin SOIC
Directly identified by NXP as a compatible predecessor; TJA1054T adds fault tolerance and lower EME while retaining the 125 kBd class and pin functions.

📋 Alternativa de referencia (no en el catálogo)

PCA82C252T

✅ Sustitución directa
📦 14-pin SOIC
Directly identified by NXP as a compatible predecessor; TJA1054T adds fault tolerance and lower EME, with a 0% stated data-rate difference at the 125 kBd application limit.

📋 Alternativa de referencia (no en el catálogo)

TJA1055T/3/C,512

✅ Sustitución directa
📦 14-pin SOIC
Related NXP 14-pin CAN transceiver with consistent terminals and package; protection or control features may differ, and the verified comparison does not establish a 0% difference across every electrical parameter.

📋 Alternativa de referencia (no en el catálogo)

TJA1054T/N1 Especificaciones

Product Type Fault-tolerant CAN transceiver
Maximum Intended Data Rate 125 kBd
Primary Application Low-speed passenger-car CAN networks
Bus Interface CANH and CANL differential bus
Encapsulado 14-pin SOIC, 3.9 mm body
Tipo de montaje Surface mount
Interface Position Between CAN protocol controller and physical bus wires
Fault Tolerance Fault-tolerant CAN operation
Electromagnetic Emission Very low EME from CANH and CANL output matching
Replacement Compatibility Pin and downwards compatible with PCA82C252T
Replacement Compatibility Pin and downwards compatible with TJA1053T
CAN Bus Mode High-speed CAN bus

Guía de configuración de pines de TJA1054T/N1 14-pin soic, 3.9 mm body

Configuración de pines para TJA1054T/N1 (encapsulado 14-pin soic, 3.9 mm body). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 14-pin soic, 3.9 mm body para TJA1054T/N1

No hay datos detallados de patillaje disponibles para TJA1054T/N1.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

TJA1054T/N1 es adecuado para 6 aplicacións: Passenger-Car Body CAN, Automotive Sensor Gateway, Industrial CAN Control, Vehicle Comfort and Body Electronics, CAN Actuator Network, Legacy CAN Interface Upgrade.

🚗

Passenger-Car Body CAN

The TJA1054T/N1 fits low-speed passenger-car body networks operating up to 125 kBd because it places a fault-tolerant CAN physical interface directly between a controller and the CANH/CANL bus. The 14-pin SOIC package preserves the footprint used by compatible TJA1053T and PCA82C252T designs. Its low EME is valuable in vehicles where several body modules share sensitive wiring. Install it only after checking the complete pin, supply, and mode-control requirements in the NXP datasheet.

🚗

Automotive Sensor Gateway

A sensor gateway can use the TJA1054T/N1 to connect a CAN controller to vehicle sensors and actuators over a 125 kBd bus. Fault-tolerant behavior helps the interface manage common wiring faults, while the strong CANH/CANL matching identified by NXP supports low electromagnetic emission. The 14-pin SOIC package is particularly useful for retrofitting an existing TJA1053T or PCA82C252T layout. Validate the gateway's grounding, bus termination, and fault-state behavior against the manufacturer specification.

🏭

Industrial CAN Control

The TJA1054T/N1 is suitable for industrial equipment that retains a low-speed CAN network originally built around a 14-pin CAN interface. Its 125 kBd target is appropriate for supervisory, configuration, and actuator-control links rather than high-bandwidth factory networks. The pin-compatible relationship with TJA1053T and PCA82C252T simplifies targeted replacements. Designers should verify electromagnetic compatibility, grounding strategy, and bus-fault requirements for the final enclosure and cable environment.

🚗

Vehicle Comfort and Body Electronics

Door modules, climate controls, seat controllers, and lighting controllers can use the TJA1054T/N1 as the physical CAN interface in a low-speed vehicle subnet. The device's fault-tolerant CAN function and very low EME help support reliable communication among body modules, while its 125 kBd rating aligns with supervisory traffic rather than high-speed data transfer. The compatible 14-pin footprint supports platform reuse. Confirm the device's operating limits and automotive qualification suffix for each production program.

⚡

CAN Actuator Network

For distributed actuator control, the TJA1054T/N1 provides the interface between a CAN controller and a physical bus carrying commands to motors, relays, lamps, or valves. Its intended 125 kBd rate is sufficient for supervisory command traffic, and the fault-tolerant architecture is valuable when wiring faults are plausible. Using a compatible 14-pin SOIC footprint allows designers to reuse established CAN routing and connector patterns. Review output behavior, bus standby requirements, and protection limits in the manufacturer datasheet.

🔧

Legacy CAN Interface Upgrade

The TJA1054T/N1 is a direct modernization option for equipment using the PCA82C252T or TJA1053T because NXP states that both can be replaced while retaining all functions. The 14-pin SOIC interface and 125 kBd low-speed application class preserve the original system architecture while adding fault-tolerant behavior and very low EME. This is valuable when production support for an older transceiver becomes difficult. Before replacement, compare every power, mode, and signal connection and retest system-level bus faults.

Resumen de productos recomendados

TJA1053T Pin-compatible predecessor CAN transceiver Se usa en: Passenger-Car Body CAN, Industrial CAN Control, Vehicle Comfort and Body Electronics, Legacy CAN Interface Upgrade PCA82C252T Compatible CAN interface design Se usa en: Passenger-Car Body CAN, Industrial CAN Control, CAN Actuator Network, Legacy CAN Interface Upgrade TJA1054AT NXP Semiconductors Se usa en: Automotive Sensor Gateway, Vehicle Comfort and Body Electronics TJA1054T/VM,512 Related ordering option for the same interface Se usa en: Automotive Sensor Gateway, CAN Actuator Network
What is the TJA1054T/N1 used for?
The TJA1054T/N1 is a fault-tolerant CAN transceiver used to connect a CAN protocol controller to the CANH and CANL physical bus wires. According to the NXP product information, it is primarily intended for low-speed passenger-car applications up to 125 kBd. It belongs to the interface-IC hierarchy and handles the physical signaling layer between digital controller circuitry and a two-wire CAN network.
What is the maximum data rate of the TJA1054T/N1?
The TJA1054T/N1 is intended for CAN communication up to 125 kBd. The NXP TJA1054 product information specifically identifies low-speed passenger-car networks as the primary application. This 125 kBd figure describes the intended maximum bus data rate and should not be confused with the higher data rates supported by high-speed CAN transceivers designed for data-intensive automotive networks.
Where can I download the TJA1054T datasheet PDF?
The official TJA1054 datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/TJA1054.pdf. It is titled “TJA1054 Fault-tolerant CAN transceiver” and is the primary document for pin assignments, electrical limits, characteristics, application information, and recommended circuits. Use the manufacturer PDF for design verification rather than relying only on catalog summaries.
Where can I find the TJA1054T pinout?
The TJA1054T pinout is identified in the NXP TJA1054 manufacturer datasheet, available from the official data-sheet link on this page. The component uses a 14-pin SOIC package, but the exact pin numbers, names, and operating descriptions must be assigned from that document. Confirm TXD, RXD, mode-control, supply, ground, CANH, and CANL connections against the datasheet before laying out or modifying a PCB.
What can replace the TJA1054T/N1?
The TJA1054T/N1 can be replaced by the PCA82C252T or TJA1053T because NXP states that the TJA1054T is pin-compatible and downwards-compatible with both devices. The replacement retains the existing functions. The TJA1054AT is another compatible NXP member, while automotive-qualified and newer CAN interface options should be checked against supply, mode-control, and fault-response requirements before substitution.
Is the TJA1054AT a drop-in replacement for the TJA1054T/N1?
Yes, NXP identifies the TJA1054AT as pin-compatible and downwards-compatible with the same PCA82C252T and TJA1053T devices supported by the TJA1054T. The two NXP parts therefore share the same functional replacement relationship in the 14-pin SOIC footprint. Confirm the qualification and ordering-temperature suffix for the intended automotive or industrial environment before approving a substitution.
TJA1054T/N1 vs TJA1053T — which is better for a new CAN design?
The TJA1054T/N1 is generally the preferable choice for a new low-speed CAN interface because it adds fault-tolerant behavior and very low electromagnetic emission to the pin-compatible TJA1053T architecture. NXP specifically lists the TJA1053T as a device that can be replaced by the TJA1054T with retention of all functions. Existing TJA1053T boards therefore offer a practical upgrade path.
TJA1054T/N1 vs PCA82C252T — can the NXP part replace it directly?
Yes, the TJA1054T/N1 is a pin-compatible and downwards-compatible replacement for the PCA82C252T. NXP states that the PCA82C252T can be replaced by the TJA1054T while retaining all functions. Its strongest improvements are fault-tolerant operation and very low EME resulting from good matching between the CANH and CANL outputs, making it a sensible interface update for compatible legacy designs.
When should I choose the TJA1054T/N1 over another CAN transceiver?
Choose the TJA1054T/N1 when a low-speed CAN system needs a fault-tolerant physical interface, low electromagnetic emission, and compatibility with an existing PCA82C252T or TJA1053T PCB. Its 125 kBd target suits passenger-car and related low-speed networks. For higher bus rates, different bus topologies, or controller interfaces requiring other voltage and mode-control arrangements, review the complete electrical specification first.
Is the TJA1054T/N1 suitable for automotive low-speed CAN networks?
The TJA1054T/N1 is suitable for the type of low-speed passenger-car CAN network described by NXP, with operation intended up to 125 kBd. Its fault-tolerant CAN interface and very low EME are particularly useful in vehicle electrical systems where bus faults and emissions must be controlled. For a production vehicle program, also verify the exact ordering suffix, environmental qualification, and system-level EMC requirements.
What is the best cross-brand equivalent for the TJA1054T/N1?
The TJA1054T/N1 should be evaluated against cross-brand parts using the same 14-pin footprint, compatible interface voltage, matching mode-control behavior, and equivalent fault-tolerant CAN performance. NXP directly confirms compatibility with the PCA82C252T and TJA1053T, but no separately identified cross-brand equivalent is established here. Use the Request a Quote form on this page to request assistance with a specific cross-brand candidate and PCB compatibility review.
Where can I buy the TJA1054T/N1 online?
The TJA1054T/N1 can be requested through the Request a Quote form on this page. The form is the appropriate channel for checking exact suffix availability, order quantity, and lead time without relying on a static catalog price. NXP and distributor listings for TJA1054T/N1 order variants are available, but an exact TJA1054T/N1 request should be confirmed before committing the MPN to a production BOM.
What is the price of the TJA1054T/N1?
Current commercial pricing for the exact TJA1054T/N1 should be obtained through the Request a Quote form on this page. The platform applies channel pricing and discounts to the structured product pricing data, so the displayed commercial figure can change with quantity and availability. Submit the required quantity and suffix details in the form to receive an actionable quotation for this exact MPN.
What is the lead time and stock status for the TJA1054T/N1?
Current stock, minimum order quantity, and lead time for the TJA1054T/N1 should be confirmed through the Request a Quote form on this page. The exact NXP suffix matters because related TJA1054T order codes can use different packing, qualification, or temperature arrangements. Providing the required quantity and production schedule in the request allows the order to be matched to the exact TJA1054T/N1 designation.
What are the key specifications of the TJA1054T/N1 that engineers should know?
The key TJA1054T/N1 specifications are its fault-tolerant CAN-transceiver function, intended low-speed operation up to 125 kBd, and 14-pin SOIC packaging. NXP also confirms pin and downwards compatibility with the PCA82C252T and TJA1053T. Its very low electromagnetic emission is attributed to strong CANH/CANL output matching, making bus-fault behavior and PCB compatibility central selection criteria.

Datos de referencia de ingeniería para TJA1054T/N1 — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the TJA1054T/N1 when updating a low-speed CAN interface that must operate up to 125 kBd and needs fault-tolerant behavior or very low electromagnetic emission. It is especially attractive for existing PCA82C252T or TJA1053T boards because NXP confirms direct replacement with retained functions. Select TJA1054AT or TJA1054T/VM,512 when the ordering, qualification, or packing arrangement better matches the production program. Consider TJA1055T/3/C,512 for a related 14-pin NXP transceiver, but verify its electrical limits and mode-control behavior rather than assuming interchangeability. Do not choose this device for a high-speed CAN link or for any design requiring a different package, supply arrangement, or bus interface.

Comparación con alternativas

Parámetro Este producto TJA1054AT TJA1054T/VM,512 TJA1053T PCA82C252T TJA1055T/3/C,512
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package 14-pin SOIC 14-pin SOIC - same 14-pin SOIC - same 14-pin SOIC - same 14-pin SOIC - same 14-pin SOIC - same
Product Type Fault-tolerant CAN transceiver Fault-tolerant CAN transceiver Fault-tolerant CAN transceiver CAN transceiver CAN interface CAN transceiver
Primary Application Low-speed passenger-car CAN networks up to 125 kBd Low-speed passenger-car CAN networks up to 125 kBd Low-speed passenger-car CAN networks up to 125 kBd Low-speed CAN networks CAN interface CAN interface

Diferenciadores clave

  • Fault-tolerant CAN operation (frente a TJA1053T)
  • Very low electromagnetic emission (frente a PCA82C252T)
  • Direct PCB migration from two legacy interfaces (frente a TJA1054AT)
  • Low-speed network specialization (frente a TJA1055T/3/C,512)

Notas de diseño

Treat the TJA1054T/N1 as a pin-compatible 14-pin SOIC update to TJA1053T and PCA82C252T layouts, but still compare every connection against the NXP datasheet. Preserve the original CANH, CANL, controller-interface, mode-control, supply, and ground routing whenever possible. Avoid changing connector polarity or bus topology during a replacement because software expectations and physical-layer behavior may remain tied to the original design.

Place the transceiver close to the CANH and CANL connector or bus-routing region to minimize trace area and susceptibility to external electromagnetic fields. Keep the CANH and CANL paths adjacent and symmetrical where practical because their matching is central to the device's very low EME behavior. Provide a low-impedance ground connection and keep high-current switching paths away from the bus-side pins and controller-interface traces.

Do not infer electrical equivalence solely from the shared 14-pin footprint. The TJA1054T/N1 is intended for low-speed CAN operation up to 125 kBd, so it should not be assumed to meet the requirements of a high-speed CAN link. Before substitution, verify supply limits, controller-interface voltage, mode-control polarity, standby behavior, bus-fault response, and the exact ordering-temperature or qualification suffix.

Use the manufacturer's application information to implement bus termination correctly and keep the termination network physically close to the relevant bus nodes rather than at the transceiver. The TJA1054 family's low EME depends on good CANH/CANL matching, but that benefit cannot compensate for a poorly terminated bus or long unbalanced stub. Validate radiated and conducted emissions at the complete product level because enclosure and cable behavior also affect compliance.

Decouple the transceiver supply locally and follow the manufacturer recommendation for capacitor placement and value. Check startup, standby, and fault-mode current in the electrical characteristics before sizing the supply because system power budget calculations must include all operating states. A local ground-plane connection should provide a short return path for bus-driver currents and reduce coupling between the transceiver and adjacent controller circuitry.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The automotive qualification suffix and environmental compliance declarations must be confirmed for the exact ordering code. The TJA1054/N1 designation is an interface IC rather than a discrete power semiconductor.

Búsquedas relacionadas

tja1054t datasheet tja1054t pdf nxp tja1054t TJA1054T/N1 datasheet pdf TJA1054T/N1 pinout TJA1054T/N1 equivalent TJA1054T/N1 replacement TJA1054T/N1 cross reference TJA1054T/N1 vs TJA1053T TJA1054T/N1 vs PCA82C252T TJA1054T/N1 125 kBd CAN TJA1054T/N1 14-SOIC TJA1054T/N1 automotive CAN TJA1054T/N1 price TJA1054T/N1 stock

Componentes & términos relacionados

NXP Semiconductors TJA1054T/N1 TJA1054T TJA1054AT TJA1053T PCA82C252T TJA1054T/VM,512 TJA1055T/3/C,512 Controller Area Network CAN transceiver CAN protocol controller physical-layer interface CANH CANL fault-tolerant CAN electromagnetic emission 125 kBd low-speed CAN passenger-car network 14-pin SOIC SOIC package family surface-mount package bus termination pin-compatible replacement
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ