TJA1054T/N1 - Fault-Tolerant 125 kBd CAN | NXP
MPN: TJA1054T/N1 ✓ AktifTJA1054T/N1 Ringkasan
A CAN transceiver is an interface IC within the wider network-interface and semiconductor hierarchy. It converts logic-level transmit and receive signals from a CAN controller into the physical differential signaling used on a CAN bus. CAN itself is a deterministic, multiplexed communication network used in automotive and industrial control systems. The TJA1054T/N1 occupies the physical-layer position between digital processing circuitry and the two-wire bus.
The TJA1054T/N1 is identified as a fault-tolerant CAN transceiver and is primarily intended for low-speed networks operating at up to 125 kBd. NXP states that the device is pin-compatible and downwards-compatible with the PCA82C252T and TJA1053T, allowing either device to be replaced while retaining the existing functions. This compatibility makes the TJA1054T a practical upgrade path for designs already using those interface devices.
The principal engineering benefit is bus-fault tolerance. NXP describes very low electromagnetic emission as an important improvement over the PCA82C252 and TJA1053T, based on strong matching between the CANH and CANL outputs. Good matching helps limit differential-mode emissions and improves signal quality on the physical bus. The TJA1054 family also retains the functional structure expected by existing CAN controllers, allowing a PCB-level replacement without changing the surrounding bus interface.
Typical uses include passenger-car body and comfort networks, low-speed automotive CAN subnets, sensor and actuator gateways, and industrial equipment that retains an automotive CAN architecture. In these systems, the transceiver connects a CAN controller to CANH and CANL, provides bus-side transmit and receive functions, and helps the network continue operating correctly when the bus is shorted to ground, shorted to supply, or open. Exact protection and operating details should be confirmed in the manufacturer datasheet.
PCB implementation should preserve the device's pin compatibility with the PCA82C252T and TJA1053T, including the same 14-pin SOIC footprint and signal assignments. Check the bus-polarity, supply, ground, transceiver-mode, and controller-interface connections against the NXP pin description before fabrication. Do not assume that all CAN transceivers are interchangeable merely because they use the same protocol; interface voltage, mode-control logic, and fault behavior must also match.
This product page combines the manufacturer compatibility information, package identification, available ordering references, and practical replacement guidance in one engineering-focused record. It also distinguishes verified drop-in choices from options that require package or function review, helping engineers evaluate a CAN bus update without relying on an incomplete cross-reference list.
Pilihan pengganti yang segera untuk TJA1054T/N1 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
TJA1054AT
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →TJA1054T/VM,512
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TJA1053T
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
PCA82C252T
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TJA1055T/3/C,512
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TJA1054T/N1 Spesifikasi
| Product Type | Fault-tolerant CAN transceiver |
| Maximum Intended Data Rate | 125 kBd |
| Primary Application | Low-speed passenger-car CAN networks |
| Bus Interface | CANH and CANL differential bus |
| Kemasan | 14-pin SOIC, 3.9 mm body |
| Jenis Pemasangan | Surface mount |
| Interface Position | Between CAN protocol controller and physical bus wires |
| Fault Tolerance | Fault-tolerant CAN operation |
| Electromagnetic Emission | Very low EME from CANH and CANL output matching |
| Replacement Compatibility | Pin and downwards compatible with PCA82C252T |
| Replacement Compatibility | Pin and downwards compatible with TJA1053T |
| CAN Bus Mode | High-speed CAN bus |
Panduan Konfigurasi Pin TJA1054T/N1 14-pin soic, 3.9 mm body
Konfigurasi pin untuk TJA1054T/N1 (14-pin soic, 3.9 mm body pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk TJA1054T/N1.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
TJA1054T/N1 patut untuk 6 aplikasis: Passenger-Car Body CAN, Automotive Sensor Gateway, Industrial CAN Control, Vehicle Comfort and Body Electronics, CAN Actuator Network, Legacy CAN Interface Upgrade.
Passenger-Car Body CAN
The TJA1054T/N1 fits low-speed passenger-car body networks operating up to 125 kBd because it places a fault-tolerant CAN physical interface directly between a controller and the CANH/CANL bus. The 14-pin SOIC package preserves the footprint used by compatible TJA1053T and PCA82C252T designs. Its low EME is valuable in vehicles where several body modules share sensitive wiring. Install it only after checking the complete pin, supply, and mode-control requirements in the NXP datasheet.
Disebarkan
Automotive Sensor Gateway
A sensor gateway can use the TJA1054T/N1 to connect a CAN controller to vehicle sensors and actuators over a 125 kBd bus. Fault-tolerant behavior helps the interface manage common wiring faults, while the strong CANH/CANL matching identified by NXP supports low electromagnetic emission. The 14-pin SOIC package is particularly useful for retrofitting an existing TJA1053T or PCA82C252T layout. Validate the gateway's grounding, bus termination, and fault-state behavior against the manufacturer specification.
Disebarkan
Industrial CAN Control
The TJA1054T/N1 is suitable for industrial equipment that retains a low-speed CAN network originally built around a 14-pin CAN interface. Its 125 kBd target is appropriate for supervisory, configuration, and actuator-control links rather than high-bandwidth factory networks. The pin-compatible relationship with TJA1053T and PCA82C252T simplifies targeted replacements. Designers should verify electromagnetic compatibility, grounding strategy, and bus-fault requirements for the final enclosure and cable environment.
Disebarkan
Vehicle Comfort and Body Electronics
Door modules, climate controls, seat controllers, and lighting controllers can use the TJA1054T/N1 as the physical CAN interface in a low-speed vehicle subnet. The device's fault-tolerant CAN function and very low EME help support reliable communication among body modules, while its 125 kBd rating aligns with supervisory traffic rather than high-speed data transfer. The compatible 14-pin footprint supports platform reuse. Confirm the device's operating limits and automotive qualification suffix for each production program.
Disebarkan
CAN Actuator Network
For distributed actuator control, the TJA1054T/N1 provides the interface between a CAN controller and a physical bus carrying commands to motors, relays, lamps, or valves. Its intended 125 kBd rate is sufficient for supervisory command traffic, and the fault-tolerant architecture is valuable when wiring faults are plausible. Using a compatible 14-pin SOIC footprint allows designers to reuse established CAN routing and connector patterns. Review output behavior, bus standby requirements, and protection limits in the manufacturer datasheet.
Disebarkan
Legacy CAN Interface Upgrade
The TJA1054T/N1 is a direct modernization option for equipment using the PCA82C252T or TJA1053T because NXP states that both can be replaced while retaining all functions. The 14-pin SOIC interface and 125 kBd low-speed application class preserve the original system architecture while adding fault-tolerant behavior and very low EME. This is valuable when production support for an older transceiver becomes difficult. Before replacement, compare every power, mode, and signal connection and retest system-level bus faults.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk TJA1054T/N1 — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | TJA1054AT | TJA1054T/VM,512 | TJA1053T | PCA82C252T | TJA1055T/3/C,512 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 14-pin SOIC | 14-pin SOIC - same | 14-pin SOIC - same | 14-pin SOIC - same | 14-pin SOIC - same | 14-pin SOIC - same |
| Product Type | Fault-tolerant CAN transceiver | Fault-tolerant CAN transceiver | Fault-tolerant CAN transceiver | CAN transceiver | CAN interface | CAN transceiver |
| Primary Application | Low-speed passenger-car CAN networks up to 125 kBd | Low-speed passenger-car CAN networks up to 125 kBd | Low-speed passenger-car CAN networks up to 125 kBd | Low-speed CAN networks | CAN interface | CAN interface |
Penyeberangsung Jelas
- Fault-tolerant CAN operation (vsTJA1053T)
- Very low electromagnetic emission (vsPCA82C252T)
- Direct PCB migration from two legacy interfaces (vsTJA1054AT)
- Low-speed network specialization (vsTJA1055T/3/C,512)
Catatan Desain
Treat the TJA1054T/N1 as a pin-compatible 14-pin SOIC update to TJA1053T and PCA82C252T layouts, but still compare every connection against the NXP datasheet. Preserve the original CANH, CANL, controller-interface, mode-control, supply, and ground routing whenever possible. Avoid changing connector polarity or bus topology during a replacement because software expectations and physical-layer behavior may remain tied to the original design.
Place the transceiver close to the CANH and CANL connector or bus-routing region to minimize trace area and susceptibility to external electromagnetic fields. Keep the CANH and CANL paths adjacent and symmetrical where practical because their matching is central to the device's very low EME behavior. Provide a low-impedance ground connection and keep high-current switching paths away from the bus-side pins and controller-interface traces.
Do not infer electrical equivalence solely from the shared 14-pin footprint. The TJA1054T/N1 is intended for low-speed CAN operation up to 125 kBd, so it should not be assumed to meet the requirements of a high-speed CAN link. Before substitution, verify supply limits, controller-interface voltage, mode-control polarity, standby behavior, bus-fault response, and the exact ordering-temperature or qualification suffix.
Use the manufacturer's application information to implement bus termination correctly and keep the termination network physically close to the relevant bus nodes rather than at the transceiver. The TJA1054 family's low EME depends on good CANH/CANL matching, but that benefit cannot compensate for a poorly terminated bus or long unbalanced stub. Validate radiated and conducted emissions at the complete product level because enclosure and cable behavior also affect compliance.
Decouple the transceiver supply locally and follow the manufacturer recommendation for capacitor placement and value. Check startup, standby, and fault-mode current in the electrical characteristics before sizing the supply because system power budget calculations must include all operating states. A local ground-plane connection should provide a short return path for bus-driver currents and reduce coupling between the transceiver and adjacent controller circuitry.
Maklumat Kesediaan
The automotive qualification suffix and environmental compliance declarations must be confirmed for the exact ordering code. The TJA1054/N1 designation is an interface IC rather than a discrete power semiconductor.