VSC8530XMW-03 Single-Port Copper Ethernet PHY | Microchip
N.º de pieza: VSC8530XMW-03 ✗ Fin de vidaVSC8530XMW-03 Descripción general
An Ethernet physical-layer transceiver, commonly called a copper PHY, converts logical data transmitted by a host controller into signals that can travel over twisted-pair Ethernet cabling. Within the network hierarchy, the VSC8530XMW-03 connects an Ethernet media system to an RGMII- or RMII-based digital controller. Its single-port design suits one copper Ethernet link while its 6 mm x 6 mm package supports compact industrial, communications, and embedded-network designs.
The principal features of this device include support for RGMII and RMII host interfaces, IEEE 802.3az Energy Efficient Ethernet, Wake-on-LAN, and a broad selection of LVCMOS I/O levels. The combination of a compact 48-QFN package and low-power, small-form-factor design is particularly useful where board area, energy use, and standardized copper connectivity are important design constraints.
The VSC8530 belongs to the VSC85xx family of industrial-grade single-port Fast Ethernet copper PHYs. The -03 device is associated with the 6 mm x 6 mm package variant of that family. Host-interface selection is a central design decision because RGMII and RMII provide different data widths and signaling arrangements. PCB layout must also preserve the high-speed digital signal integrity required between the PHY and host controller.
Typical uses include industrial Ethernet controllers, communications equipment, embedded routers, single-port network appliances, and copper network interfaces operating in compact enclosures. The device can be used where one Ethernet port is sufficient and energy-efficient link operation helps reduce power consumption during inactive periods. Its Wake-on-LAN function supports remote activation and network-maintenance workflows.
For implementation, follow the manufacturer pin-description table and recommended layout guidance when assigning all 48 package connections and decoupling capacitors. The exposed pad and thermal path require careful PCB design, while RGMII or RMII routing requires short, controlled-impedance connections. Confirm the exact interface mode, clocking arrangement, and termination requirements before releasing the PCB.
This product page combines package identification, interface-focused engineering guidance, lifecycle information, and structured comparisons with the closest documented same-family alternatives. It is intended to help hardware engineers verify footprint compatibility, select the correct -03 revision, and plan an industrial copper Ethernet implementation with fewer board-level integration errors.
Alternativas directas para VSC8530XMW-03 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con VSC8530XMW-03 (mismo factor de forma y huella) — difiere en Energy Efficient Ethernet, Host Interface.
VSC8530XMW-04
✅ Sustitución directaConsulte el precio
Ver hoja de datos →VSC8530XMW-05
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
VSC8530XMW-03 Especificaciones
| Product Type | Single-port copper Ethernet PHY |
| Ethernet Port Count | 1 port |
| Copper PHY Classification | Fast Ethernet copper PHY |
| Host Interface | RGMII or RMII |
| Energy Efficient Ethernet | IEEE 802.3az supported |
| Wake-on-LAN | Supported |
| I/O Logic Standard | LVCMOS |
| Package Type | 48-QFN |
| Package Dimensions | 6 mm x 6 mm |
| Package Construction | Single-row QFN |
| Tipo de montaje | Surface mount |
| Industrial Grade | Yes |
| Rango de temperatura de funcionamiento | -40°C to +125°C |
| Estado RoHS | RoHS3 compliant |
| Recuento de pines | 48 pins |
Guía de configuración de pines de VSC8530XMW-03 single-row qfn
Configuración de pines para VSC8530XMW-03 (encapsulado single-row qfn). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para VSC8530XMW-03.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
VSC8530XMW-03 es adecuado para 6 aplicacións: Industrial Ethernet Controller, Embedded Router Network Port, Communications Gateway, Test and Measurement Instrument, Industrial Sensor Gateway, Network Appliance Management Port.
Industrial Ethernet Controller
The VSC8530XMW-03 fits a compact industrial controller that needs one copper Ethernet link and either an RGMII or RMII connection to its network processor. Its industrial-grade designation and documented -40°C to +125°C temperature range suit equipment operating across demanding ambient conditions. The 48-QFN, 6 mm x 6 mm package preserves board area compared with larger Ethernet PHYs, while IEEE 802.3az support can reduce link activity during light traffic. The implementation should include the manufacturer-recommended magnetics, supply filtering, reference circuitry, exposed-pad layout, and controlled-impedance routing between the PHY and host controller.
Recomendado
Embedded Router Network Port
A single VSC8530XMW-03 can provide the copper Ethernet physical layer for an embedded router, gateway, or network appliance. RGMII is useful when the host controller benefits from a wider parallel data path, while RMII can reduce interface pin demand on host devices with more constrained I/O. The PHY's Wake-on-LAN capability supports remote maintenance, and Energy Efficient Ethernet can reduce activity on lightly used links. Board planning should account for clock timing, impedance-controlled host traces, isolation requirements, magnetics, and the package exposed-pad thermal path.
Recomendado
Communications Gateway
The VSC8530XMW-03 is appropriate for a communications gateway that exposes one copper Ethernet connection to a host processor. Its low-power, small-form-factor copper PHY design is useful in gateways constrained by enclosure size, and the RGMII/RMII choice lets the hardware designer balance throughput, host pin count, and layout complexity. Wake-on-LAN provides a useful path for remote equipment administration, while IEEE 802.3az assists power reduction during low-utilization periods. Validate thermal performance, copper-pair routing, magnetics layout, and host-interface timing at the system level.
Recomendado
Test and Measurement Instrument
A VSC8530XMW-03 can add a single copper Ethernet management or communication port to a compact test instrument. The 6 mm x 6 mm package allows the PHY to be placed near the board edge and network magnetics, while RGMII or RMII can connect to the instrument's control processor. Wake-on-LAN may assist remote monitoring and service access, while Energy Efficient Ethernet can reduce consumption when the instrument is connected but not transferring continuous traffic. Keep the host clocking deterministic, route high-speed interfaces with controlled impedance, and provide a thermal path from the exposed pad.
Recomendado
Industrial Sensor Gateway
The VSC8530XMW-03 can supply a single wired Ethernet connection for an industrial sensor gateway that collects data from local sensors and forwards it to an upper-level network. Its industrial-grade positioning and broad operating-temperature range align with equipment intended for factory environments. The compact QFN package supports dense board layouts, while IEEE 802.3az reduces unnecessary link activity when traffic is intermittent. The gateway must still account for Ethernet magnetics, surge and isolation requirements, cable routing, thermal conditions, and the timing margins required by the selected RGMII or RMII host interface.
Recomendado
Network Appliance Management Port
The VSC8530XMW-03 can implement a dedicated management Ethernet port on a network appliance where the primary data path uses another interface. This allows technicians to retain access to configuration, diagnostics, and remote-management functions even when the appliance's main communication link is unavailable. The single-port PHY supports both RGMII and RMII, enabling adaptation to different controller resources, and its small 48-QFN package simplifies placement near an edge connector. Wake-on-LAN supports remote recovery workflows, while the physical implementation must preserve magnetics placement, isolation, thermal-pad soldering, and high-speed host signal integrity.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para VSC8530XMW-03 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | VSC8530XMW-04 | VSC8530XMW-05 |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 48-QFN (6x6 mm) | 48-QFN (6x6 mm) | 48-QFN (6x6 mm) |
| Device Type | Single-port copper Ethernet PHY | VSC8530 copper Ethernet PHY | Single-port copper Ethernet PHY |
| Ethernet Port Count | 1 port | 1 port | 1 port |
Diferenciadores clave
- Compact single-port copper PHY integration (frente a VSC8530XMW-05)
- Industrial copper networking in a small footprint (frente a VSC8530XMW-04)
- Both host-interface options on one PHY (frente a VSC8530XMW-05)
Notas de diseño
Place the PHY close to the Ethernet magnetics and physical-layer isolation network to minimize copper-pair trace length and susceptibility to EMI. Keep the RGMII or RMII host interface free of unnecessary stubs, use the recommended solid reference plane, and route clocks with short symmetric paths. The exposed thermal pad must use the manufacturer land pattern and a thermal-via strategy compatible with the assembly process.
Select RGMII or RMII before schematic capture and preserve the associated clock, enable, and data-direction functions required by the chosen host controller. Review every pin against the -03 datasheet rather than assuming that another VSC8530 suffix has identical connections. Maintain the required input and output capacitance values because timing margin depends on host edge rate, board delay, and the physical interface selected.
Use the supply rails, decoupling network, and reference requirements specified by Microchip for the -03 configuration. Place required ceramic capacitors adjacent to their assigned power pins with short current paths and low loop area. Confirm startup sequencing, power-supply tolerance, and analog-signal grounding against the manufacturer schematic so the PHY operates correctly across input-voltage and temperature conditions.
Treat RGMII as a source-synchronous high-speed interface and RMII as a clock-referenced parallel interface with its own edge-rate requirements. Use the datasheet-recommended terminations, provide a continuous reference plane, avoid split planes beneath the PHY, and verify the exposed-pad connection through the full stack-up. Perform post-layout timing and return-path checks before fabrication.
Información de cumplimiento
A distributor technical listing identifies the VSC8530XMW-03 as RoHS3 compliant. No REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration is stated in the available information.