WM8983GEFL/V - 24-Bit Stereo Audio Codec | Cirrus Logic
N.º de pieza: WM8983GEFL/V ✓ ActivoWM8983GEFL/V Descripción general
A multimedia CODEC is a mixed-signal semiconductor that converts between digital audio streams and analog microphone, headphone, line, or speaker signals. Its functional hierarchy places the WM8983 among audio interface ICs, within audio codecs and ultimately the broader category of interface ICs. Integrating conversion, analog mixing, and speaker amplification reduces the number of discrete components required in portable audio designs.
The WM8983 provides 24-bit stereo ADCs and 24-bit stereo DACs, with I2S and PCM digital interfaces for connection to a host processor or digital audio bus. Its flexible analog mixing block supports combined playback and voice communication paths. The integrated 1 W speaker drive output allows the codec to drive a small loudspeaker directly, making it useful where a separate headphone amplifier is not required.
The device is supplied in a compact 32-QFN (5x5 mm) package suited to space-constrained handsets, portable media players, personal audio products, and embedded multimedia systems. Its low-power design targets battery-operated equipment where converter efficiency, standby behavior, and analog signal integrity influence both system heat and playback quality.
Typical uses include portable music players, mobile media devices, voice-capable portable electronics, compact speakers, and multifunction personal-audio products. The stereo recording path can capture analog microphone or line-level inputs, while the DAC path and analog mixer provide digital playback, voice monitoring, and direct speaker output within one device.
When laying out a WM8983GEFL/V board, place decoupling capacitors at the supply pins and route analog and digital return currents carefully to prevent codec noise from coupling into microphone or speaker signals. Confirm the exact clocking, digital-interface mode, and exposed-pad connection against the manufacturer datasheet before release.
This page organizes the confirmed WM8983GEFL/V capabilities, package information, sourcing path, and engineering trade-offs for engineers evaluating stereo audio codec implementations. It also distinguishes the documented order-code variants and identifies where a genuine pin-to-pin substitute must be validated rather than assumed.
Alternativas directas para WM8983GEFL/V — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con WM8983GEFL/V (mismo factor de forma y huella) — difiere en Digital Audio Interface, Package, Product Type.
WM8983GEFL/RV
✅ Sustitución directaConsulte el precio
Ver hoja de datos →WM8983GEFL
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
WM8983GEFL/V Valores máximos y características eléctricas
| Product Type | Stereo audio codec with integrated 1 W speaker driver |
| ADC Resolution | 24 bit |
| DAC Resolution | 24 bit |
| ADC Configuration | 2 ADC |
| DAC Configuration | 2 DAC |
| Digital Audio Interface | I2S, PCM |
| Speaker Drive Output | 1 W |
| Channel Configuration | Stereo |
| Encapsulado | 32-QFN (5x5 mm) |
| Tipo de montaje | Surface mount |
| Product Description | Low-power, high-quality stereo codec for portable multimedia applications |
| Analog Mixing | Flexible analog mixing functions for audio playback and voice communication |
| Digital Interface Format | I2S, PCM |
Guía de configuración de pines de WM8983GEFL/V 32-qfn (5x5 mm)
Configuración de pines para WM8983GEFL/V (encapsulado 32-qfn (5x5 mm)). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para WM8983GEFL/V.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
WM8983GEFL/V es adecuado para 6 aplicacións: Portable Digital Music Player, Voice-Enabled Mobile Media Device, Compact Bluetooth Speaker Module, Personal Audio Recorder, Digital Photo and Video Camera, Embedded Multimedia Control Panel.
Portable Digital Music Player
The WM8983GEFL/V fits a compact music player that records through two 24-bit ADCs and plays back through two 24-bit DACs. Its I2S and PCM interfaces connect the codec to an application processor, while the analog mixer supports input selection and volume control. The integrated 1 W speaker drive can feed a small internal loudspeaker, reducing the need for a separate output amplifier. Its low-power multimedia positioning is appropriate for battery-operated products, and the 32-QFN (5x5 mm) package preserves board area. Confirm supply-voltage and thermal limits against the manufacturer datasheet before selecting the speaker impedance and enclosure output level.
Recomendado
Voice-Enabled Mobile Media Device
The WM8983GEFL/V supports portable products that mix music playback with voice communication. Two 24-bit ADCs capture microphone or line-level input, while the flexible analog mixing functions combine the communication and playback paths. Digital audio is transferred through I2S or PCM to a host processor, and the 1 W speaker output provides direct small-speaker drive. This arrangement can reduce external mixed-signal components in a mobile media design. Signal-routing quality depends on correct mixer configuration, microphone preamplifier settings, and analog return grounding, so use the manufacturer register map and reference circuit during firmware bring-up.
Recomendado
Compact Bluetooth Speaker Module
A compact wireless speaker can use the WM8983GEFL/V when the module needs local microphone capture and analog audio conditioning in addition to digital playback. The 24-bit stereo DAC path receives I2S or PCM audio from a wireless audio SoC, while the analog mixer supports voice injection and level adjustment. The integrated 1 W output stage can drive a small enclosure speaker when the verified load, supply voltage, and thermal conditions permit it. Its 32-QFN (5x5 mm) package is well suited to densely populated portable modules. Decouple each supply rail at the pins and keep the exposed pad tied to the prescribed ground layout.
Recomendado
Personal Audio Recorder
The WM8983GEFL/V can serve as the audio front end in a portable recorder that captures stereo microphone or line-level signals at 24-bit resolution. Two ADCs provide the stereo inputs, and the flexible analog mixer allows monitoring and gain routing between capture and playback paths. A host processor can configure the codec over its digital control interface and exchange audio using I2S or PCM. Using the same codec for recording and monitoring can simplify signal routing, although the analog mixer still requires careful gain staging to avoid clipping. Validate microphone biasing, input impedance, clocking, and grounding against the manufacturer datasheet.
Recomendado
Digital Photo and Video Camera
The WM8983GEFL/V can support audio capture and playback in a compact camera when the product includes a small speaker and microphone. Two 24-bit ADCs handle stereo capture, two 24-bit DACs provide digital-to-analog conversion, and the I2S interface connects to a camera application processor. The analog mixer enables microphone monitoring or voice-insertion paths, while the integrated 1 W driver supplies a small onboard-speaker output. The codec's compact QFN package helps conserve camera-board area. Keep the microphone input away from display and power-converter noise sources, and verify the audio clocking scheme with the host processor design team.
Recomendado
Embedded Multimedia Control Panel
An embedded control panel with audio prompts can use the WM8983GEFL/V for playback, recording, and spoken-status feedback. The 24-bit DAC path accepts digital audio from the panel processor over I2S or PCM, while the mixer combines system sounds with voice communication. A 1 W speaker driver supports a compact internal transducer without requiring a separate amplifier in space-constrained hardware. The codec also provides analog inputs for gooseneck microphones or line sources. Because embedded panels often share power with switching regulators and displays, analog ground partitioning and local supply bypassing are essential for maintaining a low-noise audio path.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para WM8983GEFL/V — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | WM8983GEFL/RV | WM8983GEFL |
|---|---|---|---|
| Package | 32-QFN (5x5 mm) | 32-QFN (5x5 mm) | 32-QFN (5x5 mm) |
| Brand | Cirrus Logic | Cirrus Logic | Cirrus Logic |
| ADC Resolution | 24 bit | 24 bit | 24 bit |
| DAC Resolution | 24 bit | 24 bit | 24 bit |
| Digital Audio Interface | I2S, PCM | I2S, PCM | I2S, PCM |
| ADC Configuration | 2 ADC | 2 ADC | 2 ADC |
| DAC Configuration | 2 DAC | 2 DAC | 2 DAC |
| Speaker Drive Output | 1 W | 1 W | 1 W |
| Analog Mixing | Flexible analog mixing for playback and voice communication | Flexible analog mixing | Flexible analog mixing |
| Target Application | Portable multimedia | Portable multimedia | Portable multimedia |
Diferenciadores clave
- Combines stereo conversion, analog mixing, and speaker drive (frente a WM8983GEFL/RV)
- Supports both I2S and PCM host interfaces (frente a WM8983GEFL)
- Integrated two-channel ADC and two-channel DAC architecture (frente a WM8983GEFL/RV)
Notas de diseño
Follow the manufacturer application circuit for supply bypassing and place the required capacitors immediately beside the relevant WM8983GEFL/V pins. Route analog input and speaker-output signals away from digital clock lines and switching-node copper. The 32-QFN package requires careful escape routing between closely spaced pads, so review the datasheet land pattern and exposed-pad grounding instructions before releasing artwork.
Keep the digital audio bus short, use continuous reference planes beneath clock and data routes, and avoid passing microphone traces beneath or beside high-current switching paths. Apply the manufacturer's clocking scheme consistently across the host processor and codec. A stable master clock and correctly configured I2S word alignment reduce jitter, clicks, and channel-timing errors in the 24-bit data stream.
Do not select the speaker impedance, output power, or analog gain settings without checking the electrical limits in the manufacturer datasheet. Verify the /V and /RV order-code qualifiers before treating either variant as interchangeable, and confirm the exposed-pad connection, supply sequencing, and pin multiplexing in the device documentation. A matching package name alone does not establish a safe functional substitution.
Información de cumplimiento
Formal RoHS, REACH, halogen-free, and conflict-minerals declarations were not identified in the accessible product summaries. Confirm the exact orderable MPN with the manufacturer before making a compliance claim.