XC3S2000-5FG676C - 2M Gate Spartan-3 FPGA, 676-BGA | AMD
N.º de pieza: XC3S2000-5FG676C ✓ ActivoXC3S2000-5FG676C Descripción general
What is an FPGA? A field-programmable gate array is a reconfigurable digital integrated circuit whose logic and interconnect are configured by a bitstream rather than fixed in silicon. A device such as the XC3S2000 sits in the hierarchy of programmable logic devices: FPGA as the core category, then programmable logic, then digital logic ICs, then semiconductors. Because the configuration is stored in static CMOS latch memory, the same board can be re-programmed in the field to change functionality, shorten NRE, and consolidate several discrete CPLD and glue-logic parts into one device.
Key features of this device include the -5 speed grade, a 1.2 V core supply, 489 user I/O in the FG676 package, and a commercial (C) temperature grade. The Spartan-3 architecture combines configurable logic blocks (CLBs) with embedded distributed RAM, dedicated block RAM for on-chip storage, and a programmable interconnect with dedicated routing resources such as RAM16 and DSP48E1 arithmetic slices. Multipliers, FIFOs, and small state machines can therefore be consolidated into a single silicon device.
The FG676 package is a 27 x 27 mm flip-chip BGA with a 1.0 mm ball pitch, and the device is offered in both tin-lead (FG) and lead-free (FGG) ball finishes within the same Spartan-3 family. Spartan-3 devices are supported by the ISE and ISE Design Suite-style tool flows, so existing Spartan-3 bitstreams, constraints, and board-level footprints remain reusable across the family.
Typical applications include industrial control and instrumentation, video and image processing pipelines, communications and network interface line cards, test and measurement equipment, and embedded system glue logic around microprocessors. The large I/O count and block RAM make the XC3S2000 well suited to multi-channel data acquisition and protocol bridging designs.
When laying out a board around the FG676 package, route power planes with careful via stitching, keep the configuration pins accessible for multi-boot or JTAG use, and provide clean, terminated clock inputs with low jitter because most high-speed designs depend on PLL quality. Note that the Spartan-3 family is a mature, legacy platform: verify current tool and availability status before starting a new production design.
This page consolidates package, pin-count, and I/O details, drop-in package-compatible alternatives, and practical design notes that are not gathered in one place in the manufacturer datasheet, helping engineers evaluate a migration path quickly.
Alternativas directas para XC3S2000-5FG676C — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
XC3S2000-5FGG676C
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
XC3S2000-5FG676I
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
XC3S2000-4FG676I
✅ Sustitución directaConsulte el precio
Ver hoja de datos →XC3S2000-4FGG676I
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
XC3S2000-5FG676C Valores máximos y características eléctricas
| Device Type | FPGA - Spartan-3 Field Programmable Gate Array |
| Logic Families | Spartan-3 |
| System Gates | 2,000,000 gates |
| User I/O | 489 I/O |
| Package Type | 676-ball FCBGA (FG676), 27 x 27 mm |
| Ball Pitch | 1.0 mm |
| Number of Terminals | 676 balls |
| Core Supply Voltage | 1.2 V |
| Speed Grade | -5 |
| Temperature Grade | Commercial (C), 0 C to +85 C |
| Process Technology | 90 nm CMOS |
| Terminal / Pitch Type | Ball / 1.0 mm FCBGA |
| Package Body Size | 27 x 27 mm |
| Tipo de montaje | Surface Mount |
| Lead-Free Status | Lead-free variant available as XC3S2000-5FGG676C |
| Configuration | SRAM-based, re-programmable |
| Rango de temperatura de funcionamiento | 0 C to +85 C (commercial) |
Guía de configuración de pines de XC3S2000-5FG676C 27 x 27 mm
Configuración de pines para XC3S2000-5FG676C (encapsulado 27 x 27 mm). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para XC3S2000-5FG676C.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
XC3S2000-5FG676C es adecuado para 6 aplicacións: Industrial Control and Data Acquisition, Video and Image Processing Pipelines, Communications Line Cards and Protocol Bridging, Test and Measurement Instrumentation, Embedded System Glue Logic, Automotive and Transportation Auxiliary Electronics.
Industrial Control and Data Acquisition
The XC3S2000-5FG676C suits multi-channel industrial control and data acquisition front ends where channel count, not raw gate count, drives the design. Its 489 user I/O in a single 676-ball FCBGA lets one device absorb encoder, limit switch, and analog-front-end digital connections that would otherwise need several CPLDs and glue logic. Embedded block and distributed RAM hold acquisition buffers and filter coefficients without external memory, while the 1.2 V core and 90 nm process keep power and cost predictable in 24 V rack-mounted equipment. The commercial 0 C to +85 C rating suits controlled indoor cabinets; for colder sites choose the industrial XC3S2000-5FG676I.
Recomendado
Video and Image Processing Pipelines
Video capture and pixel-processing boards benefit from the XC3S2000-5FG676C because 489 I/O allow wide parallel buses to be driven directly into the fabric without external transceivers, and dedicated DSP48E1 arithmetic slices support filter and pixel arithmetic functions. A typical pipeline maps a parallel sensor interface, a colour-processing stage, and a memory frame buffer through block RAM, with the large I/O budget removing the need for a separate I/O expansion device. The 27 x 27 mm FG676 footprint keeps board area reasonable for multi-channel camera cards. Designs at higher pixel rates should confirm the DSP48E1 and block RAM counts for XC3S2000 in the family data sheet before committing resources.
Recomendado
Communications Line Cards and Protocol Bridging
Line card and protocol-bridge designs use the XC3S2000-5FG676C where many concurrent serial channels must terminate and retime data. With 489 user I/O, a single Spartan-3 can host multiple transceiver interfaces, framing logic, and a shared buffer structure, replacing several discrete logic devices and their associated level shifters. Block RAM supports deep FIFO structures for receive buffering, and the fabric tolerates the clock domain crossings common in multi-rate backplane designs. The 1.2 V core with 1.8 V or 2.5 V I/O options supports mixed-voltage board ecosystems. For designs requiring faster line rates or hardware protocol cores, evaluate the Virtex-4 and Kintex-7 families as the migration path.
Recomendado
Test and Measurement Instrumentation
Instrumentation front ends typically need many digital control and capture signals alongside deterministic timing, and the XC3S2000-5FG676C provides that I/O density in one low-cost device. A single FPGA can implement sequencers, trigger logic, and acquisition control for a bench-top analyser, replacing multiple CPLDs and microcontroller glue while keeping the design fully reconfigurable as instrument firmware evolves. The commercial temperature rating is appropriate for laboratory equipment, and the large FG676 ball array permits a generous ground plane that helps measurement integrity. Designers requiring very high sample rates or precision timing should check the global clock and PLL resources for the device in the datasheet tables, since those figures are device-specific.
Recomendado
Embedded System Glue Logic
The XC3S2000-5FG676C is frequently used as glue logic around a microprocessor or DSP, absorbing bus arbitration, peripheral interfacing, watchdog supervision, and legacy port expansion that would otherwise burden the host processor. Its 489 I/O lets one Spartan-3 replace a processor bridge, a bank of GPIO expanders, and several PAL devices, which shortens board design time and reduces part count. The large on-chip memory can be used for FIFO and register banks shared with the host bus, and the mature, low-cost platform keeps bill-of-materials expense low for volume consumer and appliance products. Because Spartan-3 is a 90 nm design, new designs should check toolchain support and consider an Artix-7 or Kintex-7 part when long-term availability matters more than unit cost.
Recomendado
Automotive and Transportation Auxiliary Electronics
Auxiliary electronic modules in transportation equipment, such as door controllers, body control sub-assemblies, and diagnostic gateways, need a compact, deterministic logic device with enough I/O to avoid multiple packages. The 676-ball FCBGA package of the XC3S2000-5FG676C keeps such modules compact, and the 489 I/O cover switch inputs, lamp drivers, and bus transceivers in a single device. Its 90 nm CMOS process is well characterised for industrial environments, and the commercial temperature range covers most cabin-mounted or sheltered electronics. Vehicle-rated designs requiring -40 C to +85 C operation or AEC-Q100 qualification should use the industrial XC3S2000-5FG676I ordering code or a current automotive-qualified family, since the C suffix part is not automotive qualified.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para XC3S2000-5FG676C — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | XC3S2000-5FGG676C | XC3S2000-5FG676I | XC3S2000-4FG676I | XC3S2000-4FGG676I |
|---|---|---|---|---|---|
| Package | 676-ball FCBGA (FG676), 27 x 27 mm | 676-ball FCBGA (FG676), 27 x 27 mm - same | 676-ball FCBGA (FG676), 27 x 27 mm - same | 676-ball FCBGA (FG676), 27 x 27 mm - same | 676-ball FCBGA (FG676), 27 x 27 mm - same |
| Brand | AMD | AMD | AMD | AMD | AMD |
| System Gates | 2,000,000 gates | 2,000,000 gates | 2,000,000 gates | 2,000,000 gates | 2,000,000 gates |
| User I/O | 489 I/O | 489 I/O | 489 I/O | 489 I/O | 489 I/O |
| Speed Grade | -5 | -5 (same) | -5 (same) | -4 (approx. 15-20% slower) | -4 (approx. 15-20% slower) |
| Temperature Grade | Commercial, 0 C to +85 C | Commercial, 0 C to +85 C | Industrial, -40 C to +85 C | Industrial, -40 C to +85 C | Industrial, -40 C to +85 C |
| Ball Finish | Standard | Lead-free (RoHS) | Standard | Standard | Lead-free (RoHS) |
| Core Supply Voltage | 1.2 V | 1.2 V | 1.2 V | 1.2 V | 1.2 V |
| Process Technology | 90 nm CMOS | 90 nm CMOS | 90 nm CMOS | 90 nm CMOS | 90 nm CMOS |
| Device Type | Spartan-3 FPGA | Spartan-3 FPGA | Spartan-3 FPGA | Spartan-3 FPGA | Spartan-3 FPGA |
Diferenciadores clave
- Direct lead-free path with no design change (frente a XC3S2000-5FGG676C)
- Wider guaranteed temperature range at identical speed (frente a XC3S2000-5FG676I)
- Full 489 I/O in one device instead of multiple logic packages (frente a XC3S2000-5FG676I)
- Timing margin retained over the -4 speed grade (frente a XC3S2000-4FG676I)
- Single silicon package versus multi-part glue logic (frente a XC3S2000-4FGG676I)
Notas de diseño
The FG676 is a 676-ball FCBGA on a 1.0 mm pitch in a 27 x 27 mm body, so the escape strategy must be fixed before routing. Use a dog-bone or via-in-pad fanout onto a 0.5 mm or 0.8 mm grid, keep the ball array outline free of test-point clutter, and reserve continuous plane areas under the array for ground and each supply rail. Place the decoupling network along the array perimeter in the same order as the supply pin groups rather than scattering it, because most of these devices fail electrically from current-sharing problems at the array edge rather than from insufficient capacitance.
The core runs from 1.2 V while I/O banks can run at other supported levels, and separating those rails on a 676-ball part requires careful plane partitioning to avoid coupling core switching noise into sensitive I/O. Estimated: with a 1.2 V core at 0.4 A plus I/O activity, core dissipation is about 0.48 W, so a 1.2 V plane with dense via stitching and a local 10 uF bulk capacitor per bank is a reasonable starting point, to be validated against the datasheet current tables. Sequence rails using the dedicated configuration pins so the device never sees an out-of-order supply.
Keep configuration pins, DONE, INIT, and PROG reachable and unobstructed by decoupling parts or test pads, because JTAG or multi-boot loading depends on clean access to these balls during board bring-up and field updates. Route clock inputs as short, differentially terminated traces on a solid reference plane and avoid running them adjacent to the ball array edge, where supply transitions are fastest. Confirm the pin constraints file for the exact ordering code so that any dedicated clock, differential, or data-capable balls are assigned as intended rather than left as general-purpose I/O.
The most frequent failure in this family is a package mismatch rather than an electrical fault: FG676 and FG900, or FG456 and FG676, are different ball maps and will not interchange despite identical device names. Second, substituting the -4 speed grade for the -5 part can break a timing-closed design that was signed off at -5, so re-run static timing after any speed-grade change. Third, lead-free and standard ball finishes are separate order codes, and a footprint that assumes one will not assemble with the other.
Estimated: in a 90 nm Spartan-3 implementation with a heavily utilized fabric and I/O, total device dissipation can approach 1 W for a fully loaded XC3S2000 at moderate switching activity. With an exposed-area thermal resistance on the order of 20 to 30 C/W on a four-layer board with modest copper, that implies a junction temperature rise of roughly 20 C to 30 C above ambient, less than the rise seen on low-copper implementations. Provide a full ground plane under the array, use thermal vias in the power pads, and confirm the junction temperature budget against the -5 speed grade timing requirements in the datasheet.
Información de cumplimiento
The RoHS-compliant, lead-free ordering code for this device is XC3S2000-5FGG676C, while XC3S2000-5FG676C uses standard balls. The commercial-grade part is not automotive qualified, so the AEC-Q100 field is not applicable; use the industrial XC3S2000-5FG676I or a current automotive-qualified family for vehicle applications.