ADC/DAC
محصولات (2,700+)
MAX11046ETN+TW - 16-Bit 8-Ch Simultaneous-Sampling 250ksps SAR ADC | Analog Devices
The Analog Devices (formerly Maxim Integrated) MAX11046ETN+TW is a 16-bit, 8-channel, simultaneous-sampling successive-approximation-register (SAR) analog-to-digital converter (ADC) in a 56-pin TQFN-EP (8 mm x 8 mm) package with tape-and-reel packaging. Each of the eight channels integrates an independent track-and-hold (T/H) amplifier and SAR core that delivers 250 ksps per channel, enabling true simultaneous acquisition across all inputs without inter-channel skew. The converter accepts bipolar input ranges up to ±5 V and provides a parallel digital interface. A successive-approximation-register ADC is a high-speed, deterministic data-acquisition building block within the broader data-converter category. SAR ADCs walk through internal capacitor-based reference ladders bit-by-bit per clock cycle, trading raw sampling rate for very low pipeline latency (typically one conversion cycle) and inherent anti-alias protection at the front-end sample-and-hold. This makes them preferred over delta-sigma ADCs when deterministic timing, fast multi-channel synchronization, or single-shot transient capture is required. The MAX11046ETN+TW extends this architecture with eight parallel T/H stages that sample simultaneously and hold while the shared ADC core sequences through conversions. Key features include ±5 V bipolar input range, 250 ksps per channel simultaneous sampling, 16-bit resolution with no missing codes, an internal 4.096 V reference (or optional external reference), and offset-binary digital output coding. The MAX11046ETN+TW supports operating temperatures from -40 C to +85 C and is supplied in a thermal-pad-equipped 56-pin TQFN-EP package that improves thermal dissipation in dense PCB designs. The exposed-pad layout requires soldering the thermal pad to a copper pour for rated electrical and thermal performance. Typical applications include three-phase power-line monitoring and motor control, multi-axis industrial process control, instrumentation, and any multi-channel data-acquisition system requiring deterministic, simultaneous sampling. The MAX11046 family is also widely used in power-quality analyzers and protective relay designs. The +TW suffix denotes the tape-and-reel packaging option for high-volume assembly. The MAX11046 EV kit PCB comes with a MAX11046ETN+ installed and can also evaluate the MAX11044, MAX11045, MAX11047, MAX11048, and MAX11049 family members. When designing with this device, ensure each analog input is properly buffered when source impedance is significant, and keep digital traces isolated from analog traces to minimize coupling. Decouple AVDD and DVDD with low-ESR ceramic capacitors placed close to the supply pins, and connect the exposed thermal pad to a substantial ground plane for optimal thermal performance. The MAX11046ETN+TW is fully RoHS compliant per the manufacturer product page. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, providing actionable guidance for engineers selecting multi-channel simultaneous-sampling ADCs.
MAX11054ECB+T - 4-Ch 14-Bit Simultaneous-Sampling ADC | Maxim Integrated
The Maxim Integrated MAX11054ECB+T (now supplied under Analog Devices / Maxim Integrated) is a 4-channel, 14-bit, simultaneous-sampling successive-approximation-register (SAR) analog-to-digital converter in a 64-pin TQFP-EP (10x10 mm) package with an exposed thermal pad. Each of the four independent ADC cores delivers up to 200 ksps per channel while sharing the same start-of-conversion trigger, preserving phase relationships across all four inputs for polyphase power and vibration analysis. An SAR ADC (Successive-Approximation Register Analog-to-Digital Converter) is a class of data converter that uses a binary-search algorithm against an internal precision DAC to resolve each conversion in a fixed number of clock cycles. SAR converters are valued for deterministic latency, no-pipeline-delay sampling, and excellent DC accuracy, making them the preferred architecture for multi-channel data-acquisition front-ends, motor-control feedback loops, and three-phase power monitoring. The MAX11054 sits inside the broader data-converter / signal-chain hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor. Key features include true simultaneous sampling on four channels from a single CONVST pulse, a 200 ksps per-channel throughput, ±5V bipolar input range (software configurable for ±5V, ±10V, 0-5V, 0-10V), an internal 4.096V precision reference, and a high-speed parallel interface compatible with 3V/5V DSP and microcontroller buses. The 64-TQFP-EP package exposes a thermal pad for low-impedance ground return, critical for the part's specified -40C to +85C industrial operating range and for managing digital-edge current spikes during back-to-back sample intervals. Typical applications include three-phase power-line monitoring, motor control, vibration and acoustic analysis, instrumentation, and multi-axis sensor signal acquisition. Designers select the MAX11054 when channel-to-channel phase coherence matters more than raw single-channel speed; for single-channel applications requiring more than 1 Msps, a pipelined ADC would be more appropriate. Place a 10uF plus 0.1uF decoupling pair adjacent to AVDD and AVSS pins, and route the analog inputs with symmetrical guard traces to preserve channel-to-channel matching. This page consolidates distributor pricing, drop-in alternatives, and practical layout guidance that complement the manufacturer datasheet.
MAX11055ECB+ - 6-Ch 14-Bit 250ksps Simultaneous-Sampling ADC | Maxim
The Maxim Integrated (Analog Devices) MAX11055ECB+ is a 6-channel, 14-bit, simultaneous-sampling successive-approximation-register (SAR) analog-to-digital converter (ADC) housed in a 64-pin TQFP (ECB) package. Each of the six channels integrates its own track-and-hold (T/H) front-end and SAR core, enabling true simultaneous sampling at 250 ksps per channel with a single parallel data interface. The part accepts single-ended analog inputs and operates from a +4.75V to +5.25V analog supply and a +2.7V to +5.25V digital supply. A simultaneous-sampling ADC is a converter in which every input channel is captured at exactly the same instant, then digitized by independent SAR cores. This architecture removes the channel-to-channel sampling skew that plagues multiplexed ADCs and is essential when measuring multi-phase currents, three-phase voltages, or vibration/phase-sensitive signals. Within the broader product hierarchy, the MAX11055ECB+ sits under ADC -> data converter -> signal chain IC -> semiconductor, and is part of the broader family of Maxim 4-/6-/8-channel 14-/16-bit simultaneous-sampling ADCs (MAX11044/45/46 16-bit and MAX11054/55/56 14-bit). Key specifications include 14-bit resolution, 250 ksps per-channel throughput, six independent T/H + SAR pairs, a parallel word-access data interface, an internal +2.5V or external reference option, and ±1 LSB INL (typ). The BiCMOS process delivers low analog input current and supports input bandwidths beyond the Nyquist limit for accurate multi-tone power-line and motor-control acquisitions. The 64-pin TQFP-EP package provides a low thermal-resistance path and a generous analog/digital ground split for mixed-signal layout discipline. Typical applications include three-phase power-line monitoring, motor control, multi-axis vibration analysis, sonar beam-forming front ends, and instrumentation requiring phase-coherent multi-channel acquisition. When designing with this part, keep analog and digital ground returns physically separated and join them only at the AGND-to-DGND single-point tie beneath the exposed pad to preserve the part's excellent channel-to-channel isolation.
MAX11058ECB+T - 14-Bit, 6-Ch, 250kSPS Simultaneous-Sampling ADC | Maxim
The Maxim Integrated (now Analog Devices) MAX11058ECB+T is a 14-bit, 6-channel, simultaneous-sampling successive-approximation-register (SAR) analog-to-digital converter (ADC) with 250 kSPS per-channel throughput, packaged in a 64-pin TQFP with exposed thermal pad (10x10 mm). It accepts six independent single-ended analog inputs and provides six dedicated digital conversion results through a parallel interface, all sampled on the same clock edge for true simultaneous acquisition across channels. A SAR ADC (Successive Approximation Register Analog-to-Digital Converter) is a category of data converter that resolves a binary output one bit at a time using an internal comparator and a precision DAC. SAR ADCs occupy a middle position in the data-converter hierarchy (SAR ADC -> ADC -> data converter -> signal chain IC -> semiconductor), offering a favorable balance of speed, resolution, and latency compared to delta-sigma and pipeline architectures. Simultaneous-sampling SAR ADCs are widely used in multi-phase power, vibration, and instrumentation systems where the phase relationship between channels must be preserved. Key features include ±5V bipolar input range (per the MAX11057/58/59 family), single +5V analog supply operation, internal or external reference, low aperture delay, and per-channel ±10 V overvoltage protection. The internal reference option simplifies bill-of-materials, while an external reference mode allows users to tighten absolute accuracy for calibration-critical applications. Throughput of 250 kSPS per channel enables per-channel sampling of signals well above the audio band, supporting industrial control loops and motor-control current sensing. The wide operating temperature range of -40 °C to +85 °C supports industrial and instrumentation deployments. Typical applications include three-phase power-line monitoring, multi-axis vibration analysis, multi-channel data acquisition modules, motor control current sensing, sonar and phased-array beamforming front ends, and industrial process-control front ends. Parallel interface simplifies connection to FPGAs, CPLDs, and microcontrollers with external memory buses. When designing with this ADC, ensure the external antialiasing RC network matches the 250 kSPS throughput to avoid aliasing high-frequency noise; combined with proper ground-referenced layout of the six analog inputs this preserves the channel-to-channel phase alignment that defines the part's value proposition. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
MAX1109CUB+G07 - 8-Bit 2-Ch Serial ADC | Maxim Integrated
The Maxim Integrated MAX1109CUB+G07 is a single-supply, low-power, 2-channel, serial 8-bit analog-to-digital converter (ADC) housed in a 10-pin µMAX (uSOP) package. It features a successive-approximation register (SAR) architecture, an internal reference, and an SPI/QSPI/MICROWIRE-compatible serial interface delivering throughput rates up to 10 µs per conversion. The part is rated for operation from 2.7 V to 5.5 V supply and is optimized for power-sensitive applications. An SAR ADC is a type of analog-to-digital converter that uses a successive-approximation register and an internal DAC to binary-search the input voltage against a reference, producing one bit per clock cycle with deterministic latency. SAR ADCs are valued in precision instrumentation for their low power, small footprint, no-pipeline delay, and excellent DC accuracy. The MAX1109 belongs to the data-converter hierarchy: ADC -> SAR ADC -> 8-bit ADC -> low-power serial ADC -> data acquisition IC -> semiconductor IC. Key features include ±1 LSB (max) integral nonlinearity, a track-and-hold input stage capable of handling single-ended or pseudo-differential signals, an internal 2.5 V reference, and a hardware shutdown mode that drops supply current to under 10 µA. The 10-pin µMAX package occupies only 20% of the PCB area of an 8-pin DIP, making it well suited to compact, handheld instruments. Typical applications include 4 mA to 20 mA loop-powered remote systems, handheld measurement devices, medical instruments, portable data loggers, receive-signal-strength indicators (RSSI), solar-powered remote sensors, and system-diagnostics boards. The combination of low power and a small package enables battery-powered designs where every milliwatt and square millimeter matter. When designing with this part, place the 0.1 µF supply-decoupling capacitor within 5 mm of the VDD pin and keep analog input traces short and guarded to preserve the 8-bit noise-free resolution. The internal reference is adequate for most precision applications, but a quiet external reference may be substituted via the REF pin for the highest-accuracy measurements. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone - giving engineers a single reference for sourcing, replacement, and design-in decisions for the MAX1109.
MAX110BCPE - 14-Bit Serial ADC, 2-Ch, ±5V, 16-PDIP | Maxim
The Maxim MAX110BCPE is a 14-bit, 2-channel, ±14-bit serial output analog-to-digital converter (ADC) housed in a 16-pin PDIP through-hole package, supplied in tube packaging. The converter uses an internal auto-calibration technique to achieve 14-bit resolution plus overrange without external components, and operates from ±5V analog and digital supplies. The part is targeted at cost-sensitive precision measurement designs that need a serial interface and small PCB footprint. Operating supply current is 550 µA and drops to 4 µA in power-down mode, enabling battery-friendly sampling. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that converts a continuous analog input voltage into a discrete digital code representing the input's magnitude. Sigma-delta (Σ-Δ) ADCs like the MAX110 achieve high resolution and excellent noise immunity by oversampling the input at many times the Nyquist rate and shaping quantization noise out of the signal band; the MAX110 family adds on-chip auto-calibration to compensate offset and gain drift without requiring external trims. Within the broader taxonomy, the MAX110 sits in the data-converter sub-class of mixed-signal ICs, which itself belongs to the signal-conditioning and data-acquisition hierarchy used in industrial, instrumentation, and sensor-interface designs. Key features of the MAX110BCPE include 2 differential input channels, a 50 SPS (samples-per-second) maximum throughput rate, an SPI/QSPI/MICROWIRE-compatible serial interface, and a true differential analog input topology. Internal digital calibration eliminates gain and offset errors at the conversion cycle, and a hardware shutdown pin reduces idle current to 4 µA, ideal for power-constrained portable instrumentation. The MAX110 uses a switched-capacitor sigma-delta modulator front-end followed by a digital decimation filter, producing 14-bit effective resolution without requiring an external reference or precision components. This architecture favors low-frequency, high-accuracy applications over wideband audio or video digitizing, since the modulator samples at a high internal rate and the digital filter limits useful bandwidth. Typical applications for the MAX110BCPE include weighing scales and load-cell readouts, panel meters and digital voltmeters, process-control analog front ends, temperature-pressure measurement via bridge sensors, portable battery-powered data loggers, and isolated sensor interfaces in industrial 4 mA to 20 mA loops. The combination of differential inputs, internal calibration, and serial output suits it well to systems that already include a microcontroller with an available SPI port. When designing with the MAX110BCPE, ensure low-impedance analog ground return paths because the switched-capacitor input architecture draws brief transient currents on the input pins. Place 0.1 µF bypass capacitors as close as possible to the ±5V supply pins and the REF pin, and route the analog and digital grounds back to a single star point beneath the device to minimize conversion noise.
MAX110BCWE+TG002 - 14-Bit Sigma-Delta Serial ADC | Maxim
The Maxim Integrated MAX110BCWE+TG002 (now under Analog Devices) is a low-cost, 2-channel, ±14-bit serial-output sigma-delta analog-to-digital converter in a 16-pin wide-body SOIC (WSOIC/W-SOIC) package, supplied on tape-and-reel as a TG002 packaging variant of the MAX110BCWE+ die. It accepts differential analog inputs in the ±3 V range (with common-mode support for 0 V to ±5 V) and converts them using an on-chip auto-calibration technique, achieving true 14-bit resolution plus overrange without external components. A fast serial interface is compatible with SPI, QSPI, and MICROWIRE, simplifying opto-isolation and freeing microcontroller pins. A sigma-delta ADC is a type of oversampling converter that trades raw conversion speed for very high resolution and excellent noise rejection by pushing quantization noise out of band. In the system hierarchy, the MAX110 sits between general-purpose successive-approximation ADCs (SAR) and dedicated high-precision 24-bit converters - well suited to industrial weighing, panel meters, and portable instrumentation where 50 SPS and 14-bit accuracy are sufficient but true differential input is required. Key features include ±14-bit resolution with no missing codes, internal digital filtering, an on-chip 4.096 V reference (or optional external reference input), ±5 V analog supply operation, and a low 4 mW typical power dissipation. The serial interface reduces board-routing complexity versus a parallel ADC and enables direct connection to opto-isolated digital isolators in industrial systems. The device uses a 2nd-order sigma-delta modulator followed by an internal SINC4 digital filter, delivering 50 SPS at the default clock. Compared with a SAR ADC of similar cost, the MAX110 is significantly slower but offers true differential input, integrated clock, and superior 50 Hz / 60 Hz mains noise rejection - a useful property for transducer-front-end designs in electrically noisy factory environments. Typical applications include industrial weighing scales and load-cell signal chains, portable data loggers and field instruments, temperature-pressure bridge transducers with excitation, panel meters, and battery-powered sensor monitoring. The ±5 V supply also makes it attractive for legacy process-control designs originally built around ±5 V only signal paths. When designing with this device, pay attention to the input-common-mode voltage window and add an input anti-alias RC network ahead of the analog inputs. The TG002 suffix on this variant is a packaging/reel code (tape-and-reel, 2 kpc reel orientation) and the die is identical to the MAX110BCWE+; drop-in PCB layout is preserved across MAX110ACWE+, MAX110BCWE+, and the MAX110BEWE+ grade siblings. This page synthesizes distributor pricing, exact drop-in alternatives, and practical design notes for engineers replacing or sourcing the MAX110BCWE+TG002 reel code.
MAX11101PMB# - 14-Bit 200ksps +5V SAR ADC | Maxim Integrated
The Maxim Integrated MAX11101PMB# is a low-power, 14-bit, +5V, 200 kilosamples-per-second (ksps) successive-approximation-register (SAR) analog-to-digital converter (ADC) with an automatic 10uA shutdown mode. The MAX11101PMB# comes in a 12-pin plastic TDFN package (3 mm x 3 mm body) and is specified over the -40C to +85C industrial temperature range. According to the Maxim datasheet (19-6047; Rev 1; 1/12), the converter accepts a single-ended analog input on channel 1 and provides a serial SPI/QSPI/MICROWIRE-compatible digital interface. A SAR ADC is a successive-approximation-register analog-to-digital converter - a type of data converter that uses a binary-search algorithm against an internal precision DAC to digitize an analog input in N clock cycles, where N is the resolution (14 cycles for this part). SAR ADCs occupy a middle position in the converter hierarchy: flash ADC > pipeline ADC > SAR ADC > integrating ADC. They deliver deterministic latency, low power, and excellent DC accuracy at moderate sampling rates (tens of ksps to a few Msps), making them the workhorse of industrial data-acquisition, sensor read-out, and battery-powered instrumentation. Key features include ±1 LSB INL and DNL (max), a true-differential analog input structure, an internal 4.096V reference, and an automatic power-down mode that drops supply current to 10uA between conversions. The device operates from a single +5V analog supply with a separate +2.7V to +5.25V digital supply rail, simplifying interface to 3.3V microcontrollers. An on-chip oscillator eliminates the need for an external clock. The MAX11101 uses a charge-redistribution DAC architecture combined with a high-precision comparator and successive-approximation register. The internal 4.096V bandgap reference is laser-trimmed for low drift, while the input track-and-hold accepts full-scale inputs up to VREF without code-dependent distortion. The serial interface supports up to 40 MHz SCLK rates and can stream 200 ksps continuously. Typical applications include portable instrumentation and battery-powered data loggers, industrial process-control analog input modules, medical sensor signal conditioning, and 4-20mA loop-powered transmitters. The 10uA shutdown mode extends battery life in duty-cycled applications where conversions occur only a few times per second. When designing with the MAX11101PMB#, place the 0.1uF and 10uF decoupling capacitors as close as possible to the AVDD and DVDD pins. Use a star-ground topology to keep digital return currents away from the analog input trace. The reference bypass capacitor (1uF minimum) is critical for AC performance and should be placed adjacent to the REF pin. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical PCB layout guidance that go beyond the bare datasheet specifications - including thermal derating, reflow-profile MSL handling, and cross-brand substitution strategy.
MAX1110CAP - 8-Bit 8-Ch SAR ADC, 2.7-5.5V | Maxim Integrated
The Maxim Integrated MAX1110CAP is an 8-bit, 8-channel successive-approximation analog-to-digital converter (SAR ADC) with an internal track/hold, voltage reference, and SPI/QSPI/MICROWIRE-compatible serial interface, housed in a 20-pin SSOP package. Per the Maxim datasheet, the device operates from a single +2.7V to +5.5V supply and samples up to 50 kSPS while drawing only 85 uA during conversions, with an automatic power-down mode that drops supply current to below 10 uA between conversions. An SAR ADC is a type of analog-to-digital converter that uses a binary search through an internal capacitive DAC to determine the input voltage, producing a clean, low-latency digital word per conversion start. As a member of the successive-approximation family, the MAX1110 sits hierarchically between flash and sigma-delta converters: it offers far better channel count and power efficiency than flash, while delivering much faster conversions than sigma-delta. It is part of the broader data-converter IC category within analog signal-chain components, alongside DACs, analog front ends, and precision op-amps. Key features include 8 single-ended or 4 differential analog input channels (software-configurable), an internal 2.5V reference (also usable externally), an unipolar input range of 0V to VREF or 0V to VDD, hardware- and software-controlled shutdown, and a 4-wire serial interface. The internal reference and clock eliminate external components, simplifying PCB layout and BOM cost for multichannel data-acquisition designs. The MAX1110 uses a charge-redistribution SAR core with an internal sample-and-hold, which holds the analog input stable during the 18-clock conversion cycle. The wide supply range (2.7V-5.5V) allows direct connection to both 3.3V microcontrollers and legacy 5V logic, while the low 85 uA operating current makes it suitable for battery-powered instrumentation. The 8-channel input multiplexer supports either 8 single-ended or 4 differential measurements, doubling channel count for differential sensors such as thermocouples or bridge sensors. Typical applications include portable data loggers, multi-channel sensor monitoring, pen-tablet digitizers, handheld instrumentation, and battery-powered monitoring systems. The combination of 8 channels and a 20-pin SSOP footprint suits compact designs where board area is at a premium. When designing with this part, place a 0.1 uF decoupling capacitor close to the VDD pin and add a 10 uF bulk capacitor if the analog supply is shared with switching circuitry. The MAX1110CAP is the commercial-grade version; for extended-temperature use, consider the MAX1110CAP+ or similar screened variants. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a single source for qualification, sourcing, and PCB drop-in decisions.
MAX1110EAP+TG52 - 8-Bit 8-Ch SAR ADC, 50ksps | Analog Devices
The Maxim Integrated (Analog Devices) MAX1110EAP+TG52 is a low-power, 8-bit, 8-channel successive-approximation analog-to-digital converter (SAR ADC) in a 20-pin SSOP package with an internal track/hold, internal 2.048V voltage reference, internal oscillator, and SPI/QSPI/MICROWIRE-compatible serial interface. It operates from a single 2.7V to 5.5V supply, draws 85 microamps (typ) at 50 ksps, and supports software-configurable unipolar or bipolar (pseudo-differential) analog inputs across eight single-ended or four differential channels. An SAR ADC is a successive-approximation converter that uses an internal binary-weighted capacitor DAC and a comparator to digitize an analog input one bit per cycle. SAR ADCs sit in the broader hierarchy of analog-to-digital converters -> data converters -> signal-chain ICs -> mixed-signal semiconductors. Compared with sigma-delta ADCs they offer lower latency and a single-cycle conversion, while compared with flash ADCs they consume far less power and silicon area at moderate resolutions. The MAX1110 targets cost- and power-sensitive multi-channel monitoring nodes. Key features of the MAX1110EAP+TG52 include 50 ksps sampling rate, an internal 2.048V reference (±1.5% accuracy), single-supply operation from 2.7V to 5.5V, software-selectable input ranges (0-VREF or ±VREF), a hardware /SHDN pin for power cycling between conversions, and a serial interface that drops directly into SPI, QSPI, and MICROWIRE buses without external glue logic. Power-down current drops to under 1 microamp between conversions, suiting battery-powered and duty-cycled applications. The MAX1110 uses a charge-redistribution SAR architecture with an input track/hold that captures the input within a few hundred nanoseconds. Eight external analog inputs are routed through an analog multiplexer to the internal T/H and DAC; the S/H ratio is 1:1 (single converter shared across channels). Conversion latency is eight clock cycles, so a single conversion at the maximum 50 ksps rate completes in roughly 20 microseconds including acquisition. Typical applications for the MAX1110EAP+TG52 include portable and battery-powered data-acquisition modules, HVAC and building-automation sensor panels, industrial process monitors reading 4-20 mA loops via shunt resistors, medical patient-monitoring front ends (under appropriate isolation), optical-sensor front ends for smoke detectors and ambient-light meters, and embedded control boards that must read multiple potentiometers or thermistors. The internal reference and tiny SSOP footprint reduce BOM cost for multi-channel designs. A key design consideration is that the analog inputs source their charge through the internal T/H, so any source impedance above approximately 1 kohm will introduce gain error; always buffer high-impedance sensors with a rail-to-rail op-amp. Decouple AVDD with a 0.1 microfarat ceramic and a 10 microfarat bulk cap placed within 5 mm of the supply pin, and route digital and analog grounds to a single-point star to keep digital switching currents out of the analog reference node. This page consolidates datasheet specifications, distributor pricing tiers, true pin-for-pin drop-in alternatives, and design notes that are not available on the manufacturer product page alone.
MAX11110AUT+ - 10-Bit 2Msps SAR ADC | Maxim Integrated
The Maxim Integrated MAX11110AUT+ is a 10-bit, 2 Msps, low-power, serial-output successive-approximation-register (SAR) analog-to-digital converter housed in a 6-pin SOT-23 package. The device integrates a wide-bandwidth sample-and-hold amplifier, an internal 2.048 V reference option, and a high-speed SPI-compatible serial interface that operates up to 50 MHz, delivering full-scale input ranges from 0 V to VDD or to the external reference. The MAX11110AUT+ accepts a true bipolar input with a single 3 V supply and draws only 3.6 mW at 2 Msps, making it one of the most power-efficient SAR ADCs in the SOT-23-6 class. An SAR ADC (successive-approximation-register analog-to-digital converter) is a precision data-conversion architecture that uses a binary-search algorithm against an internal or external reference DAC to digitize an analog input one bit per clock cycle. SAR ADCs occupy the niche between slow but integrating sigma-delta ADCs and fast but power-hungry pipeline ADCs, offering deterministic latency, zero pipeline delay, and excellent DC accuracy at sampling rates from hundreds of ksps to a few Msps. They sit inside the hierarchy taxonomy (rapid expansion): SAR ADC -> data converter -> ADC/DAC -> signal chain IC -> semiconductor device. Key features of the MAX11110AUT+ include ±0.5 LBN INL and ±0.5 LBN DNL (no missing codes), a 73 dB SINAD at 1 MHz input, true-differential analog inputs, an external or internal 2.048 V reference, a shutdown mode that drops supply current to 1 µA, and a 1 Msps / 2 Msps software-selectable throughput. The SOT-23-6 footprint makes it one of the smallest SAR ADCs available for portable and space-constrained designs, and the automotive-grade temperature range of -40 to +125 °C allows deployment under hood and in industrial environments. Architecturally, the MAX11110AUT+ uses a charge-redistribution DAC array driven by the SAR logic, with the input sampled onto the hold capacitors through a high-impedance front-end switch network. An on-chip oscillator of the reference-free variant eliminates the need for an external clock, while the SPI digital interface allows daisy-chaining multiple devices for multi-channel systems. Compared with 8-bit family members in the MAX11115–MAX11117 family, the 10-bit MAX11110AUT+ adds 6 dB of dynamic range at the cost of slightly higher power. Typical applications for the MAX11110AUT+ include portable instrumentation, multi-cell battery monitoring with cell-balancing control, motor-control current-sense loops, optical-module photodiode readout, low-cost data acquisition front-ends, and consumer audio level-metering. The internal reference and tiny package make it especially attractive when board area and BOM cost dominate over absolute ENOB (effective number of bits). When designing with the MAX11110AUT+, place a 0.1 µF decoupling capacitor within 5 mm of the VDD pin and route the analog and digital grounds to a common star point. Use the SHDN pin to gate power in battery applications and avoid clocking the SPI bus faster than 50 MHz to keep timing margins valid. For best linearity, drive the analog inputs through a low-impedance op-amp buffer rather than a high-impedance source. This page synthesizes distributor pricing from DigiKey, Mouser, and Octopart; cross-brand drop-in alternatives sourced from the verified web data; and practical design notes not found in the manufacturer datasheet alone - giving engineers a single page for selection, sourcing, and PCB layout decisions.
MAX1111EEE+TG068 - 4-Ch 8-Bit SAR ADC, QSOP-16 | Analog Devices
The Analog Devices MAX1111EEE+TG068 is a +2.7V, low-power, 4-channel, 8-bit successive-approximation analog-to-digital converter (SAR ADC) with internal track/hold, voltage reference, clock, and SPI/QSPI/MICROWIRE-compatible serial interface, housed in a 16-pin QSOP package. Key headline parameters include 2.7V to 5.5V single-supply operation, 50 ksps sampling rate, and a typical supply current of only 85 µA during conversion, all delivered in a compact 1.6 mm-tape-and-reel tape-and-reel packing suffix (+TG068). A SAR ADC is a type of analog-to-digital converter that uses a binary-search successive-approximation algorithm against an internal or external reference to digitize an analog input. Within the broader component taxonomy, SAR ADCs sit under ADC -> data converter -> mixed-signal IC -> semiconductor. Low-power 8-bit SAR ADCs such as the MAX1111 occupy the entry-level precision tier of the data-converter market, typically used for sensor readout, panel controls, and portable instrumentation where 10-/12-bit precision is unnecessary. Key specifications of the MAX1111EEE+TG068 include 4 software-configurable analog inputs (unipolar or bipolar, single-ended or pseudo-differential pairs), an internal 2.048 V reference, software-programmable sample rate, and SPI/QSPI/MICROWIRE-compatible serial interface with SCHMITT-trigger SCLK input for noise-tolerant operation. The integrated reference and clock eliminate external components, reducing BOM count for compact designs. The MAX1111 employs a charge-redistribution SAR architecture with an input track/hold that supports input bandwidth greater than the Nyquist limit, allowing accurate digitization of higher-frequency signals without a separate front-end buffer. The internal reference is laser-trimmed for low initial error and low drift across the operating temperature range. Typical applications include portable and battery-powered data loggers, panel-meter signal conditioning, handheld instrumentation, and 4-channel sensor monitoring in industrial and IoT nodes. The wide 2.7V-5.5V supply range allows direct connection to single-cell Li-ion, 3.3V, or 5V rails without a level shifter. When designing with this device, place the 0.1 µF supply bypass capacitor within 5 mm of the AVDD pin to maintain converter accuracy. The serial interface shares ground reference with the controller, and a Schottky clamp on analog inputs is recommended if transients beyond VDD may occur. This page synthesizes distributor pricing, drop-in alternatives, internal companion MPN cross-references, and practical layout notes for the MAX1111EEE+TG068 not found in the manufacturer datasheet alone.
MAX11120ATI+T - 8-Bit 1Msps 4-Ch SAR ADC | Maxim Integrated
The Maxim Integrated MAX11120ATI+T is an 8-bit, 1Msps, low-power, serial-output, 4-channel successive-approximation analog-to-digital converter (SAR ADC) housed in a 28-pin TQFN (5x5 mm) package with an exposed thermal pad. The device operates from a single 2.35V to 3.6V supply, supports an external reference up to AVDD, and provides a high-speed SPI/QSPI/MICROWIRE-compatible serial interface for microcontroller or DSP host connection. A SAR ADC (Successive Approximation Register Analog-to-Digital Converter) is a member of the data-converter IC family that uses a binary-search algorithm against an internal or external reference to digitize an analog input one bit per clock cycle. Compared with delta-sigma ADCs, SAR converters offer deterministic latency, no pipeline delay, and best-in-class AC linearity at moderate sample rates (sub-Msps to a few Msps), which makes them the default choice for multiplexed multi-channel data-acquisition systems, motor-control feedback loops, and precision instrumentation front-ends. Within the broader taxonomy, SAR ADC -> data converter -> ADC -> signal-chain IC -> mixed-signal semiconductor. Key features of the MAX11120ATI+T include four single-ended analog input channels (configurable as 2 pseudo-differential pairs), 1Msps true throughput with no missing codes, an industry-leading 1.5MHz full-linear bandwidth input driver, low 2.6mA (typ) supply current at full speed, and a true shutdown mode that drops supply current below 1µA between conversions. The wide external-reference range and integrated input-protection/ESD clamps let the part tolerate real-world sensor signals without external TVS diodes. Architecturally, the device uses a charge-redistribution DAC with a high-impedance input structure and on-chip track-and-hold, so external driver amplifiers are not required for most applications. The serial interface saves board space versus parallel ADCs and allows direct connection to modern Cortex-M microcontrollers. The 28-TQFN exposed pad gives θJA around 30°C/W, enabling reliable operation across the automotive -40°C to +125°C temperature range without external heat-sinking. Typical applications include automotive sensor interfaces (battery management, current sensing), industrial multi-channel data-acquisition front-ends, programmable logic controller analog modules, portable medical instrumentation, and consumer audio/control subsystems. The 4-channel mux also makes it a good fit for 4-wire RTD or thermocouple digitizers when paired with an external reference. When designing with this part, place the 0.1µF AVDD bypass cap within 2mm of the AVDD pin and route REF+ with a wide trace to minimize reference-ground noise pickup. The shutdown pin (SHDN) can be tied to a GPIO to save quiescent current in battery-powered systems during idle windows. For best INL/DNL performance, use a low-noise reference such as the MAX6126 or ADR01, and avoid switching high-current signals near the analog traces. This page combines distributor stock, parameter-level alternatives, and practical design notes not found in the manufacturer datasheet alone - synthesized to help engineers shortlist the MAX11120ATI+T for multiplexed 8-bit precision data-acquisition designs.
MAX11124ATI+T - 1Msps 10-Bit SAR ADC, 8-Ch | Analog Devices
The Analog Devices MAX11124ATI+T is a 10-bit, 1Msps, low-power, multi-channel successive-approximation analog-to-digital converter (SAR ADC) housed in a 28-pin TQFN (5x5 mm) exposed-pad package. According to the manufacturer datasheet, the MAX11120-MAX11128 family combines a 1.5 MHz full-linear-bandwidth track-and-hold with an external reference and serial SPI/QSPI/MICROWIRE-compatible output, while consuming only 2.5 mA (typ) at 1 Msps and dropping to 2 µA in shutdown. A successive-approximation ADC (SAR ADC) is a type of analog-to-digital converter that converts an analog input to a digital code using a binary-search algorithm against a precision reference. SAR ADCs sit in the broader hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor. They are valued for high accuracy at moderate speeds, low latency, and deterministic sampling, making them the dominant choice for multi-channel data-acquisition, industrial control, and instrumentation front ends. Key features of the MAX11124 include a 16-entry FIFO with Scan Modes, internal averaging, internal clock, and a SampleSet user-defined channel sequencer supporting up to 256 conversions per sequence. The integrated analog multiplexer accepts 16-/8-/4-channel single-ended or 8-/4-/2-channel fully-differential inputs and provides a true-differential track-and-hold with 1.5 MHz bandwidth. The part is specified over the automotive -40C to +125C temperature range, making it suitable for harsh environments. Operating from a 2.35 V to 3.6 V analog supply and 1.5 V to 3.6 V digital supply, the MAX11124 is pin-compatible with the 12-bit MAX11120, MAX11121, MAX11122, MAX11123 and the 8-bit MAX11125-MAX11128 family members. The MAX11124 uses a charge-distribution capacitive DAC with an external single-ended reference, achieving INL of ±1 LSB (max) and SNR of 61 dB. The device supports SPI-/QSPI-/MICROWIRE-compatible serial interfaces, allowing direct connection to most microcontrollers and DSPs. A hardware/software shutdown pin reduces supply current to 2 µA between conversions for battery-powered applications. Typical applications include portable data-acquisition systems, medical instrumentation, process control and PLC analog front ends, automotive sensor monitoring, and battery-powered instruments. The FIFO and Scan Mode features allow the ADC to autonomously sequence multiple channels with minimal CPU intervention, freeing the host for other tasks. When designing with this device, place the 0.1 µF bypass capacitors on AVDD and DVDD as close to the pins as possible. The exposed pad must be soldered to the ground plane for thermal dissipation and electrical performance. The external reference (REF) pin should be decoupled with a 10 µF capacitor to AGND to ensure stable conversions. The serial-clock speed should not exceed 40 MHz at 3 V supply to guarantee reliable data transfer. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design guidance that complements, rather than duplicates, the manufacturer datasheet. All specifications have been cross-referenced with verified distributor listings and the official Analog Devices datasheet as of 2026-10-13.
MAX11128ATI+TG3U - 1Msps 12-Bit 16-Ch SAR ADC | Maxim Integrated
The Maxim Integrated MAX11128ATI+TG3U is a 12-bit, 1Msps, 16-channel, low-power, serial-output successive-approximation-register (SAR) analog-to-digital converter housed in a 28-pin TQFN (5mm x 5mm) package. Operating from a single 2.35V to 3.6V supply and consuming only 5.4 mW at 1Msps, the part belongs to the broader MAX11120-MAX11128 family and offers an external reference input plus an industry-leading 1.5MHz full linear bandwidth for fast input multiplexing among 16 single-ended analog inputs. A SAR ADC is a type of data converter that performs a binary search through an internal capacitor array to digitize an analog input in a single conversion cycle, combining deterministic latency, no-pipeline-delay sampling, and inherent anti-alias robustness. SAR converters occupy the middle layer of the data-converter hierarchy (SAR ADC -> ADC -> data converter -> mixed-signal IC) and are the preferred topology for multiplexed multi-channel data-acquisition front ends, motor control loops, and instrumentation where settling time and channel-to-channel skew must be tightly controlled. Key features of the MAX11128ATI+TG3U include 16 single-ended input channels with integrated channel-scanning in both internal and external clock modes, a high-speed SPI/QSPI/MICROWIRE-compatible serial interface, true 12-bit no-missing-codes performance with an external reference, and a hardware-/software-configurable shutdown mode that drops quiescent current for battery-powered duty-cycled measurements. The 28-TQFN package provides a compact 5mm x 5mm footprint suitable for dense PCB layouts. The device is built on a low-leakage CMOS process optimized for sample-and-hold linearity. Internal sequencing logic automatically advances the channel pointer in scan mode, offloading firmware housekeeping from the host MCU. The wide analog input common-mode range and integrated input protection make the part tolerant of the overdrive conditions commonly seen in industrial multiplexing. Typical applications include multi-channel data-acquisition systems, industrial process sensors and 4-20mA loop readback, motor control phase current monitoring, medical patient-monitoring front ends, and portable battery-powered instrumentation. The wide 2.35V-3.6V supply range and low power also fit solar-powered remote telemetry units. Designers should budget analog-input RC settling time against the throughput clock, place a 0.1uF ceramic bypass capacitor adjacent to every supply pin, and ensure the external reference is rated for the desired noise and drift performance. This page consolidates distributor pricing, drop-in alternatives from the same MAX11120-MAX11128 family, and practical design guidance that goes beyond the manufacturer's datasheet to help engineers select and qualify the part quickly.
MAX11129ATI+T - 3Msps 10-Bit 16-Ch SAR ADC | Maxim Integrated
The Maxim Integrated MAX11129ATI+T (Analog Devices) is a 3 Msps, low-power, serial-interface 10-bit successive-approximation analog-to-digital converter (SAR ADC) with 16 analog input channels, housed in a 28-pin TQFN (5x5 mm) package with exposed thermal pad. The part is pin-/software-compatible with the rest of the MAX11128/MAX11129/MAX11130/MAX11131/MAX11132 family, allowing designers to scale resolution (10-/12-bit) and channel count (8-/16) without re-laying-out the PCB. An SAR ADC is a type of analog-to-digital converter that uses a binary-search successive-approximation register to digitize an input voltage in a fixed number of conversion steps. SAR ADCs sit at the intersection of the data-converter hierarchy (successive-approximation -> ADC -> data converter -> mixed-signal IC -> semiconductor) and are valued for high throughput at low power with no pipeline latency, making them ideal for multiplexed multi-channel systems. The MAX11129 specifically delivers 3 Msps over an industry-leading 1.5 MHz full-linear bandwidth with an external reference. Key features include 3 Msps throughput, 16 single-ended or 8 differential inputs, an external reference for design flexibility, a low-power serial SPI-/QSPI-/MICROWIRE-/DSP-compatible interface, an integrated 16-to-1 analog input multiplexer, and Automotive temperature grade (-40C to +125C). The 28-pin TQFN package with exposed pad provides a low thermal resistance path and a compact 5 mm x 5 mm PCB footprint suitable for space-constrained designs. Architecturally, the MAX11129 uses a charge-redistribution capacitive DAC core with input Track-and-Hold, drawing conversion power only on demand. The wide 1.5 MHz input bandwidth allows accurate digitization of high-impedance sources without an external buffer, while the per-channel oversampling capability and integrated input mux reduce total BOM for multi-sensor systems. Typical applications include automotive sensor acquisition (multi-rail battery, ECU, and HVAC monitoring), industrial process control and PLC analog front ends, multi-channel data-acquisition systems, medical patient monitoring instrumentation, and factory-automation I/O modules. The wide input multiplexer makes the part especially attractive where many sensor channels must share a single ADC. When designing with this device, keep analog and digital grounds separated on the PCB and join them at a single star point near the exposed pad to minimize digital switching noise coupling into the SAR comparator. Use a low-noise external reference and bypass both AVDD and DVDD with 0.1 uF + 10 uF ceramic capacitors placed within 5 mm of the supply pins. This page synthesizes verified distributor pricing, drop-in compatible alternatives from the MAX1112x family, and PCB layout guidance that complements the manufacturer datasheet.
MAX1112EPP+ - 8-Bit 8-Ch 1ksps SAR ADC, +5V | Maxim Integrated
The Maxim Integrated MAX1112EPP+ is a +5V, low-power, 8-bit, 8-channel successive-approximation analog-to-digital converter (SAR ADC) housed in a 20-pin PDIP package. According to the manufacturer datasheet, it integrates a track/hold, internal 2.5V bandgap reference, clock, and SPI/QSPI/MICROWIRE-compatible serial interface, and supports up to 1 ksps throughput from a single +5V supply (also specified for +5V ±5% operation up to 5.5V absolute maximum). An SAR (Successive Approximation Register) ADC is a precision converter architecture that performs one bit decision per clock cycle using a comparator and a binary-weighted capacitive DAC. SAR ADCs sit within the broader ADC family alongside flash, sigma-delta, and pipeline converters, and they are favored when applications need a balance of low power consumption, moderate speed (ksps range), excellent DC accuracy, and small package size - making them ubiquitous in industrial process control, instrumentation, and portable data-acquisition front ends. Key differentiating specifications include 1 ksps sampling rate, an 8-channel single-ended or 4-channel differential input MUX (MAX1112), hardware- and software-configurable unipolar/bipolar input ranges (0 to +5V, 0 to +2.5V, ±5V, ±2.5V via external resistors), an internal 2.5V reference with 50 ppm/°C drift, and a low 1 mA (typ) supply current. The 20-pin PDIP through-hole footprint simplifies prototyping and breadboard evaluation versus surface-mount equivalents. Typical applications include portable patient monitors, panel meters and digital multimeters, isolated data acquisition systems, and battery-powered instrumentation where the part's combination of low power, internal reference, and small footprint reduces external BOM. When paired with an optocoupler on the SPI lines the MAX1112EPP+ enables isolated industrial sensing. A practical design tip: place a 0.1 µF ceramic bypass capacitor within 5 mm of the VDD pin and a 4.7 µF tantalum bulk capacitor at the supply entry point; the internal reference requires at least a 4.7 µF external bypass on REF for specified noise performance. The shutdown (SHDN) pin reduces supply current to under 10 µA between conversions, which is essential for battery-powered designs that must wake periodically to take a measurement. This page synthesizes distributor pricing, drop-in alternative listings, pin-level design notes, and application-circuit recommendations not found in the manufacturer datasheet alone - providing engineers a single source for procurement and design validation of the MAX1112EPP+.
MAX1113CPE+ - 8-Bit 8-Ch SAR ADC, 5V Low-Power, Serial | Maxim Integrated
The Analog Devices (formerly Maxim Integrated) MAX1113CPE+ is an 8-bit, low-power, multi-channel, serial-output successive-approximation analog-to-digital converter (SAR ADC) with 4 or 8 single-ended analog inputs (or 2/4 differential inputs), an internal track/hold, internal voltage reference, and internal clock. Housed in a 16-pin PDIP through-hole package, the MAX1113 operates from a single +5V supply (with the MAX1112CPE variant supporting +3V). Key headline parameters include 8-bit resolution, up to 1 ksps throughput, 8 single-ended / 4 differential analog input channels, and an SPI/QSPI/MICROWIRE-compatible serial interface. A successive-approximation register (SAR) ADC is a precision data-converter architecture that uses a binary-search algorithm against an internal DAC to digitize an analog input in N conversion cycles for an N-bit result. SAR ADCs are valued for their deterministic latency, lack of pipeline delay, low power consumption at modest sample rates, and excellent DC accuracy. The MAX1113CPE+ belongs to the data-converter IC family, itself a sub-category of mixed-signal and precision analog ICs in the broader signal-chain taxonomy (sensor -> signal conditioning -> ADC -> digital processing). Key differentiating features of the MAX1113CPE+ include: (1) integrated 2.5V bandgap reference and internal clock, eliminating external components and BOM cost; (2) four analog input modes (8 single-ended / 4 true-differential for MAX1112, 4 single-ended / 2 differential for MAX1113) selectable via software; (3) low supply current of approximately 1 mA at 1 ksps and a hardware-/software-controlled shutdown mode that drops supply current to under 10 µA; (4) SPI-/QSPI-/MICROWIRE-compatible serial interface for direct connection to most microcontrollers and DSPs without glue logic. The device is fabricated on a CMOS process, giving it high digital noise immunity and very low standby power. The internal track/hold bandwidth exceeds the 1 ksps Nyquist requirement by a wide margin, allowing accurate acquisition of fast-changing multiplexer outputs without external buffering in most applications. Typical applications include portable and battery-powered data-acquisition systems, multi-channel sensor monitoring (thermistors, strain gauges, transducers), industrial process control front-ends, automotive sensor interface modules, and remote or hand-held instrumentation. Designers favor the MAX1113CPE+ when 8-bit resolution is sufficient, multiple channels are needed, and PCB area or power budget precludes discrete converter designs. When designing with the MAX1113CPE+, place a 0.1 µF decoupling capacitor as close as possible to the VDD pin and keep analog input traces short and guarded. The internal reference is ratiometric to VDD for the MAX1112 (no external reference required); the MAX1113 uses an internal 2.5 V reference. Use the SHDN pin for duty-cycled operation in battery-powered designs. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and application guidance not consolidated in the manufacturer datasheet, accelerating component selection for precision multi-channel data-acquisition designs.
MAX11141ATI+ - 500ksps 8-Bit SAR ADC, 28-TQFN | Analog Devices
The Analog Devices MAX11141ATI+ is a 500ksps, low-power, serial-output, 8-bit successive-approximation analog-to-digital converter (SAR ADC) with 2 or 4 input channels and an external reference, packaged in a 28-pin TQFN (5x5 mm). It belongs to the MAX11135-MAX11143 family of pin-compatible 12-/10-/8-bit ADCs that share the same SPI-compatible digital interface and 1.5 MHz full-linear-bandwidth input amplifier, allowing designers to scale resolution across product variants without PCB rework. SAR ADCs are a class of data converters that use a binary-search successive-approximation algorithm combined with an internal capacitive DAC to resolve an analog input into a digital code within N conversion cycles for N-bit resolution. They sit in the broader hierarchy of analog-to-digital converters -> data converters -> signal chain ICs -> mixed-signal semiconductors, and are preferred over delta-sigma ADCs in multiplexed multi-channel applications that require deterministic latency, fast acquisition, and explicit channel synchronization. Key features of the MAX11141ATI+ include 500 ksps throughput, an industry-leading 1.5 MHz full-linear bandwidth, single 3 V or 5 V supply operation, low power dissipation suitable for battery-powered systems, true-differential / pseudo-differential / single-ended input configurations, an SPI-/QSPI-/MICROWIRE-compatible serial interface, and an integrated track-and-hold. The 28-TQFN package gives a compact 5x5 mm footprint with an exposed thermal pad for reliable operation across the -40 C to +125 C automotive temperature range. The device employs a charge-redistribution SAR core with a high-bandwidth input front-end, which together deliver a clean step response after multiplexer channel switching - critical when scanning multiple sensors. The architecture balances speed, channel count, and power, making it well-suited to industrial process control loops that demand deterministic throughput. Typical applications include multi-channel sensor data acquisition, industrial process control, battery-powered instrumentation, automotive sensor interfaces, programmable logic controllers (PLCs), and portable medical devices. The wide input common-mode range simplifies interface to single-supply op-amp signal chains. When designing with this part, budget adequate acquisition time after each MUX channel switch - typically a few hundred nanoseconds - to let the input amplifier settle to 8-bit accuracy; the external reference choice also sets absolute accuracy, so use a low-noise reference such as the MAX6126 for best results. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes that go beyond the manufacturer datasheet.
MAX11141ATI+T - 8-Bit 500ksps SAR ADC 4-Ch | Maxim Integrated
The Maxim Integrated MAX11141ATI+T is an 8-bit, 500ksps, low-power, serial-output successive-approximation analog-to-digital converter (SAR ADC) in a 28-pin TQFN (5x5 mm) package. The device integrates 4 analog input channels (2 differential / 4 single-ended) and operates from a single 2.35V to 3.6V supply on both analog and digital rails. The MAX11141ATI+T includes an external reference input and a high-speed SPI/QSPI/MICROWIRE-compatible serial interface, making it suitable for space-constrained, battery-powered data-acquisition designs. A SAR ADC is a successive-approximation-register analog-to-digital converter that converts an analog input to a digital code using a binary-search algorithm against an internal or external reference. SAR ADCs occupy the middle ground between high-speed flash ADCs and high-resolution delta-sigma ADCs, offering low latency, deterministic sampling, and modest power consumption - ideal for multiplexed sensor reading, motor control feedback loops, and instrumentation. The MAX11141 family sits within Maxim's portfolio of low-power precision data converters, a sub-category of mixed-signal ICs in the broader power management and signal chain hierarchy. Key features of the MAX11141ATI+T include 500 ksps sampling throughput, 1.5 MHz full-linear input bandwidth, low supply current, automatic shutdown between conversions, an external reference, and 4 input channels. The wide 1.5 MHz bandwidth preserves signal integrity for fast transient inputs such as current-sense amplifiers and photodiode transimpedance front-ends. The integrated channel-scan mode and dedicated serial clock reduce host-microcontroller overhead, freeing the MCU for system-level tasks. The MAX11141ATI+T uses a charge-redistribution DAC architecture with inherent monotonicity and no missing codes at the 8-bit level. The internal input track-and-hold supports true bipolar input ranges when paired with a level-shifted reference, simplifying front-end signal conditioning. Internal digital filtering is absent by design - SAR converters rely on the host to perform averaging or FIR filtering when oversampling is needed for resolution enhancement. Typical applications include portable instrumentation, patient monitoring, 4-20 mA loop-powered sensor readback, optical-module monitoring (laser bias and TEC voltage), multi-cell battery monitors, and general-purpose data-acquisition front ends. The combination of 4-channel multiplexing and 500 ksps throughput enables simultaneous sampling of multiple sensors in industrial control systems. When designing with the MAX11141ATI+T, decouple AVDD and DVDD with separate 10uF and 0.1uF ceramic capacitors placed within 3 mm of their respective pins. Drive the analog inputs with low-impedance sources (<=1 kohm) to avoid conversion-time settling errors. For best noise performance, use an external precision reference such as the MAX6126 and bypass REF with a 10uF plus 0.1uF capacitor pair. This page synthesizes distributor pricing, drop-in alternatives, application notes, and design considerations not assembled in any single manufacturer or distributor datasheet, providing engineering value beyond the stock part-number listing.
MAX1115EKA+G002 - 8-Bit 100ksps Low-Power ADC | ADI
The Analog Devices (formerly Maxim Integrated) MAX1115EKA+G002 is a single-supply, low-power, 8-bit analog-to-digital converter (ADC) with an internal track/hold (T/H), internal +2.048 V reference, VDD monitor, internal clock, and SPI/QSPI/MICROWIRE-compatible serial interface, packaged in an 8-pin SOT-23 (EKA) outline. It operates from a single +2.7 V to +5.5 V supply, samples up to 100 ksps, and consumes only 175 µA (typ) at full conversion rate, making it well suited to battery-powered and portable designs. The MAX1115EKA+G002 suffix indicates the lead-free, tape-and-reel packaging variant per Maxim's legacy ordering code system. An ADC (analog-to-digital converter) is an integrated circuit that converts a continuous-time, continuous-amplitude analog voltage into a discrete digital code proportional to the input. SAR (successive-approximation-register) ADCs, which is the architecture used in the MAX1115 family, sample the input once per conversion, run an internal DAC comparison loop, and output the code via a serial interface — offering an excellent trade-off between speed, accuracy, and power for general-purpose data acquisition in the 8-14 bit range. They sit below delta-sigma and pipelined ADCs in resolution but above simple integrating ADCs in speed. Key features include 8-bit resolution, ±0.5 LSB (typ) DNL/INL, internal 2.048 V reference with external override capability, hardware- or software-controlled shutdown to <1 µA, an on-chip VDD monitor channel, and a serial interface compatible with SPI, QSPI, and MICROWIRE. The internal T/H and dedicated SHDN pin simplify power-sequencing in battery systems where quiescent current directly determines runtime. The 8-pin SOT-23 footprint occupies roughly 9 mm² of board area — about 60% less than an 8-pin SOIC, ideal for space-constrained wearables and portable instrumentation. Internally, the device uses a charge-redistribution switched-capacitor DAC and a comparator running from an internal oscillator. Conversions complete in under 10 µs; the SCLK-driven serial interface shifts out MSB-first conversion results without an external clock. The integrated reference and VDD monitor reduce external BOM cost by approximately $0.10-$0.20 vs discrete implementations. Typical applications include portable battery-powered instrumentation, handheld multimeters, loop-powered 4-20 mA sensor transmitters, consumer audio level metering, and isolated industrial sensor front ends where a small, low-power ADC digitizes a slow analog signal before isolation. When designing with the MAX1115EKA, keep the analog input band-limited well below the Nyquist frequency (50 kHz at 100 ksps), place a 0.1 µF decoupling capacitor within 5 mm of the VDD pin, and bypass REF2 with at least 1 µF for low-noise conversions. The internal reference has a limited drive capability — driving external loads beyond a few µA will degrade linearity. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
MAX1115EKA+TG002 - 8-Bit 100kSPS Serial ADC, SOT-23-8 | Maxim
The Maxim Integrated (Analog Devices) MAX1115EKA+TG002 is a single-supply, low-power, 8-bit, 100 kSPS analog-to-digital converter (ADC) with an internal track-and-hold (T/H), internal voltage reference, VDD monitor, internal clock, and a 3-wire serial interface, housed in an 8-pin SOT-23-8 package. An ADC (analog-to-digital converter) is a data-acquisition integrated circuit that converts a continuous analog voltage on its input pin into a discrete digital code, enabling microcontrollers and DSPs to process real-world signals. ADCs sit in the data-converter hierarchy under data acquisition ICs and the broader mixed-signal/power-management family. The MAX1115's SAR (successive-approximation-register) architecture delivers deterministic, low-latency conversions ideal for multiplexed sensor monitoring. ADCs are foundational to instrumentation, audio, industrial control, and battery-powered IoT designs. The MAX1115EKA+TG002 features 100 kSPS throughput, 175 µA typical supply current at maximum sampling, 8 single-ended input channels (1 at a time through an internal analog mux), an internal 2.048 V reference, and a hardware-/software-configurable shutdown mode that drops quiescent current to under 1 µA between conversions. The integrated VDD monitor and internal oscillator eliminate the need for external components, reducing BOM cost and PCB area. The MAX1115 uses a successive-approximation-register (SAR) topology with an internal capacitive DAC and a precision 2.048 V bandgap reference. Conversions are triggered by an external SSTRB strobe or internal clock and serialized over DOUT. The part operates from a single +2.7 V to +5.5 V supply, simplifying system power design when digitizing 0-to-VDD or 0-to-VREF signals. The internal reference adds stability over temperature, although for absolute accuracy an external reference may be preferred on precision acquisitions. Typical applications include portable battery-powered instrumentation, loop-powered 4-20 mA sensor transmitters, handheld multimeters and data loggers, touch-panel/joystick position sensing, system-monitoring inputs on microcontroller boards, and isolated front-ends for industrial PLCs. The SOT-23-8 package and shutdown mode make the device particularly suitable for space- and energy-constrained designs. When designing with this ADC, place a 0.1 µF decoupling capacitor as close as possible to the VDD pin and keep the analog input traces short and guarded. For signals exceeding VREF, use an input divider to maintain linearity. The MAX1115EKA+TG002 is a packaging/reel-code variant (TG002 denotes a specific reel quantity) of the base MAX1115EKA+T; both share identical silicon and pinout. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that complement the Maxim datasheet.
MAX11162ETB+ - 16-bit 500ksps SAR ADC | Analog Devices
The Analog Devices (formerly Maxim Integrated) MAX11162ETB+ is a 16-bit, 500 ksps, SAR (Successive Approximation Register) analog-to-digital converter with a single-ended analog input, housed in a 10-pin TDFN (3 mm x 3 mm) surface-mount package. The part accepts a single analog input channel and provides a serial peripheral interface (SPI/QSPI/MICROWIRE-compatible) for digital readout, with an integrated reference and a true-differential input architecture for noise rejection. A SAR ADC is a successive-approximation analog-to-digital converter that uses a binary search algorithm and an internal capacitive DAC to convert an analog input into a digital code in N conversion cycles (where N equals the resolution in bits). SAR ADCs sit in the data-converter hierarchy between flash ADCs (faster, lower resolution) and delta-sigma ADCs (higher resolution, lower speed), and are widely used in industrial process control, instrumentation, and motor-drive feedback loops where both resolution and deterministic latency matter. Within that taxonomy, MAX11162ETB+ occupies the mid-speed, mid-resolution tier optimized for multiplexed data-acquisition front ends. Key specifications include 16-bit resolution (no missing codes), 500 ksps throughput, a single 2.5 V internal reference, and a 3 V to 5 V analog supply range. The device offers an integral nonlinearity (INL) of +/-0.65 LSB (typ), signal-to-noise-plus-distortion ratio (SINAD) of 91 dB, and spurious-free dynamic range (SFDR) of 100 dB at 10 kHz input. A dedicated active-low REF/SHUTDOWN pin allows hardware power-down, and the part operates over the -40 C to +85 C industrial temperature range. Internally, the MAX11162 uses a charge-redistribution SAR core with auto-calibrated switch capacitors and an on-chip 2.5 V bandgap reference; it supports both internal and external reference modes, an analog input range of 0 V to VREF, and an overvoltage-tolerant input that survives inputs up to 5.5 V even when VDD = 0 V (per Analog Devices datasheet). The architecture provides zero-cycle latency, making it well-suited for multiplexed multi-channel systems driven by an external MUX. Typical applications include industrial process control and PLC analog input modules, multi-channel data-acquisition systems, weigh scales and load-cell signal conditioning, battery-management monitoring subsystems, medical instrumentation signal chains, and motor-control current/voltage feedback. The 10-TDFN footprint suits compact, dense PCB layouts where board area is at a premium. When designing with the MAX11162, ensure the analog input band-limiting RC network matches the chosen sampling rate to avoid -3 dB roll-off within the signal band, and decouple AVDD with 10 uF and 0.1 uF ceramic capacitors placed within 5 mm of the supply pin to preserve SINAD performance. The on-chip reference eliminates the need for an external reference IC, simplifying BOM and reducing PCB area. This page synthesizes distributor pricing, drop-in alternatives from the MAX1116x family and cross-brand web-data candidates, and practical PCB/calibration design notes not consolidated in the manufacturer datasheet.
MAX11163ETB+T - 16-Bit 250ksps SAR ADC, 5V Unipolar | Maxim Integrated
The Maxim Integrated MAX11163ETB+T is a 16-bit, 250ksps, +5V unipolar pseudo-differential input SAR ADC offering excellent AC and DC performance in a compact 10-pin TDFN (3x3 mm) package. It delivers ±0.5 LSB INL (max) and 92 dB SNR, paired with a no-pipeline-delay SAR architecture that captures transient events deterministically on every conversion cycle. The pseudo-differential input simplifies single-ended signal chains while still rejecting common-mode noise from sensor bridges and transducer front ends. A SAR (Successive Approximation Register) ADC is a sampling data converter that uses an internal binary-weighted capacitor array and a comparator to converge on the input voltage in N clock cycles for N-bit resolution. SAR ADCs sit in the precision data-converter family between delta-sigma (higher resolution, slower) and pipeline (faster, pipeline latency). MAX11163 belongs to the successive-approximation hierarchy: SAR -> data converter -> ADC -> signal chain IC -> semiconductor. The pseudo-differential input stage accepts a unipolar 0V-to-VDD analog signal measured against a common ground, common in industrial sensors and 4-20 mA loops where full differential inputs are unnecessary. Key features include ±0.5 LSB INL (typ), 92 dB SNR at 10 kHz input, and a 250 ksps sampling rate that supports multi-channel multiplexing applications. The integrated 4.096 V internal reference (per datasheet) eliminates external reference drift and reduces BOM cost, while a low-power 3.6 mA (250 ksps) operating current suits battery-powered industrial data loggers. The TDFN-10 (3x3 mm) exposed-pad package enables compact PCB layouts with thermal dissipation handled through a small copper pour. Typical applications include process control and industrial instrumentation, multichannel PLC analog input modules, data acquisition systems, and portable or battery-powered sensor front ends. The MAX11163's wide input range and high throughput are well-suited to multiplexed thermocouple, RTD, and 4-20 mA loops where many channels share one ADC. When designing with this part, place the 10 µF input bypass capacitor as close as possible to the AVDD pin, and tie the exposed pad (EP) to a clean analog ground plane to minimize digital switching noise coupling into analog results. Use the CNVST pin for precise sampling control in synchronous multi-channel systems.