محصولات (44,000+)

EPC144L120 - Altera/Intel EPC1441 Configuration Device 120-QFP
EPC144L120

EPC144L120 - Altera/Intel EPC1441 Configuration Device 120-QFP

The Intel EPC144L120 is a member of the EPC1441 family of serial configuration devices, supplied by Intel (formerly Altera), designed to load the configuration bitstream of ACEX 1K, APEX 20K, FLEX 10K, and Mercury-class FPGAs over a single-wire serial interface. The EPC144L120 variant specifies the 120-pin QFP operating range and uses a low-voltage CMOS SRAM-based architecture to store the FPGA configuration image. A Configuration Device is a non-volatile (one-time-programmable, OTP) serial memory specifically architected to stream configuration data into an Altera FPGA during power-up. It connects to the host FPGA through a dedicated serial configuration interface (DATA, DCLK, nCONFIG, nSTATUS, CONF_DONE). Compared to a generic serial EEPROM, a configuration device adds FPGA-aware handshaking, automatic reconfiguration on bitstream error, and pin-level compatibility with Altera/Intel FPGA configuration controllers. Key features of the EPC144L120 family include 100,000 (EPC1441 naming convention indicates density family; specific density bits to be confirmed from datasheet) configuration bits, a continuous-streaming serial interface, 3.3 V or 5 V tolerant I/O, and a QFP-120 (L120 suffix) plastic package for surface-mount assembly. Programming is performed once by Altera's software tools, after which the device retains the bitstream indefinitely without external supplies. In a typical system, the EPC144L120 sits next to the target FPGA and is wired to its configuration pins. On power-up, the FPGA drives nSTATUS low, then the EPC144L120 clocks the bitstream out through DATA into the FPGA's configuration RAM. Engineers designing with this device should ensure proper decoupling on VCC and that the nINIT_CONF / nCONFIG pull-ups follow the Altera reference schematic, otherwise the device may fail to enumerate on cold start.

RFQ تماس
EPC144L20 - 440kbit OTP Config PROM for FPGAs | Altera/Intel
EPC144L20

EPC144L20 - 440kbit OTP Config PROM for FPGAs | Altera/Intel

The Altera (Intel Programmable Solutions Group) EPC144L20 is an OTP (One-Time Programmable) configuration PROM designed to load configuration bitstreams into Altera FPGA devices at power-up, supplied in a 20-pin LCC (Leadless Chip Carrier) package. The device stores 440,800 bits organized as 440,800 × 1, and uses a serial interface that targets legacy Altera FPGA families. What is a configuration PROM? It is a non-volatile memory device that holds the FPGA's configuration bitstream and delivers it serially to the FPGA during power-up initialization, before the FPGA enters user mode. Without a configuration source, SRAM-based FPGAs cannot operate, because their configuration RAM is volatile. Configuration PROMs sit in the boot chain between the system power-on reset and the FPGA's configuration controller (e.g., Altera FPP, PS, or AS modes). Key features include a 3.3V single supply, a four-pin serial interface (nCS, DCLK, DATA, nCONFIG/nSTATUS) compatible with Altera's configuration controller, industrial operating temperature range, and a leadless ceramic-style 20-pin LCC package that supports socketed programming and high-reliability applications. The LCC package offers a compact footprint with perimeter leads that simplify board integration in legacy and industrial systems. The EPC144L20 uses an anti-fuse OTP cell array, meaning each bit can be programmed exactly once. After programming, the bitstream is permanent for the device lifetime. The serial interface is clocked by the FPGA at frequencies defined in the legacy Altera configuration protocol. The device is one of the older EPC1xxx family members (EPC1441/EPC144/EPC1213/EPC1064), predating the modern EPCQ serial flash family. Typical applications include legacy Altera FPGA configuration bitstream storage for FLEX 10K, ACEX 1K, APEX 20K, and Mercury FPGA families, factory-floor industrial controllers where the OTP cell ensures configuration stability, and aerospace/defense retrofits where socketed ceramic-style PROMs simplify field programming. When designing with this device, ensure the configuration mode selected in the FPGA matches the serial protocol expected by the EPC144L20. Voltage sequencing (VCC ramp before nCONFIG release) must follow the legacy Altera reference schematic. OTP programming requires a single programming cycle - re-programming an already programmed device is not possible. This page synthesizes legacy distributor availability, same-family drop-in alternatives (EPC1441LC20, EPC144ILC20), and design notes specific to legacy Altera configuration boot chains.

RFQ تماس
EPC144LC-20 - Altera OTP Configuration PROM | 20-PLCC
EPC144LC-20

EPC144LC-20 - Altera OTP Configuration PROM | 20-PLCC

The Intel / Altera EPC144LC-20 is an OTP (One-Time Programmable) configuration memory device from Altera's EPC144 family, designed to store FPGA configuration bitstreams for legacy Altera FPGA devices such as the EPF10K and FLEX series. Housed in a 20-pin PLCC (9x9 mm) package, this serial-configuration PROM provides non-volatile storage that loads the configuration data into a target Altera FPGA at power-up through the proprietary serial configuration interface. A Configuration PROM is a type of non-volatile serial memory used to bootstrap programmable logic devices. In the hierarchy of programming technologies, the EPC144 belongs to the OTP EPROM family, sitting below modern flash-based PROMs and above discrete bitstream storage solutions. It functions as a small, low-density serial ROM that interfaces with an FPGA's configuration controller, presenting itself as a peripheral device that delivers configuration frames on demand during the FPGA's multi-stage boot sequence. The EPC144 family represents Altera's second-generation configuration architecture that preceded the flash-based EPCS and EPCQ families. Key features of the EPC144LC-20 include 440,800 bits of OTP storage, a serial daisy-chain configuration interface, compatibility with FLEX 10K, FLEX 8000, and ACEX 1K FPGA families, low-power CMOS process technology, and a 20-pin PLCC package with a J-lead footprint. The -20 speed grade denotes a 20 ns access time, suitable for configuration of Altera FPGAs operating at configuration clock frequencies up to approximately 50 MHz. The EPC144LC-20 uses a serial daisy-chain architecture allowing multiple PROMs to be cascaded for larger bitstreams. Programming is performed using the Altera Logic Programmer card or compatible third-party programmers via JTAG-like boundary-scan mechanisms. The device operates from a single 5V supply and offers standard CMOS input thresholds, making it directly compatible with 5V-tolerant FPGA configuration pins of legacy Altera devices. Typical applications include legacy industrial control systems, telecom infrastructure retrofits, and defense/aerospace systems where the original Altera FLEX 10K or ACEX 1K FPGA designs must be maintained. Engineers designing new products should consider migrating to flash-based EPCQ or serial configuration devices from modern vendors, as the EPC144 family is no longer in active production. When designing with the EPC144LC-20, ensure proper decoupling (0.1 uF ceramic capacitor near VCC) and verify that the FPGA's configuration mode pins select serial configuration mode. The OTP nature means that bitstreams cannot be erased or rewritten, so design verification must occur before programming. This page synthesizes distributor availability, drop-in configuration PROM alternatives, and practical design considerations not found in a single manufacturer document.

RFQ تماس
EPC144LC20 - 144KB Serial Config PROM, 20-LCC | Intel (Altera)
EPC144LC20

EPC144LC20 - 144KB Serial Config PROM, 20-LCC | Intel (Altera)

The Intel (formerly Altera) EPC144LC20 is a 144-Kbit serial configuration memory device in a 20-pin LCC (Leadless Chip Carrier) package, designed for configuring Altera FPGA families via the serial configuration scheme. It provides 144,000 bits of non-volatile storage that is loaded into the FPGA's configuration SRAM at power-up via the dedicated serial configuration interface (DATA, DCLK, nCONFIG, nSTATUS, CONF_DONE). An FPGA configuration PROM is a one-time or few-time programmable serial memory that holds the FPGA's bitstream. When the system powers up, the FPGA loads its logic configuration from the PROM through a synchronous serial link. The EPC144LC20 is part of Altera's classic EPC1 series configuration memories, designed to support legacy Altera FPGA families such as the FLEX 6000, FLEX 8000, FLEX 10K, ACEX 1K, MAX 7000, MAX 3000 and APEX 20K series. The PROM is organized as a serial shift register; an internal oscillator generates the configuration clock, simplifying host design. Key features include 144 Kbit storage capacity, automatic continuous configuration on power-up, low-pin-count serial interface (4 signal pins plus VCC/GND), 3.3V or 5V operation, in-system programmable via IEEE Std 1532 / Jam STAPL, and a compact 20-pin LCC surface-mount footprint (also known as LCC-20 or JLCC-20). The device is one-time programmable (OTP) in standard configuration, simplifying bill-of-material by removing external programming steps at board build. Programming is performed via the JTAG-compatible 4-wire interface using Altera's Quartus II / MAX+PLUS II toolchains. Typical applications include configuration memory for legacy Altera FPGAs, industrial controllers using FLEX 10K or APEX 20K devices, telecom line cards with MAX 7000 glue logic, retrofits of legacy Altera designs where original EPROM-based configuration is replaced by a single chip, and embedded systems that boot from a serial bitstream. The EPC144LC20 is also widely used in CPLD-based glue logic designs where a small FPGA is configured by an adjacent configuration PROM. When designing with this device, place decoupling capacitors as close as possible to the VCC pins (typically one 0.1 uF ceramic per supply pin). The LCC-20 package has no exposed thermal pad; the device draws minimal current during configuration (typically <50 mA active, <100 uA standby) so no heatsink is required. Ensure the JTAG chain (TCK/TMS/TDO/TDI) is terminated correctly if multiple Altera devices share the chain; use Altera's ByteBlaster or USB-Blaster cables for in-system programming. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. The EPC144LC20 is a legacy configuration device with mature second-source options; consult the Intel (Altera) Configuration Devices datasheet for full timing specifications.

RFQ تماس
EPC144PC8 - Altera 433800612 Configurator DIP-8 | Intel
EPC144PC8

EPC144PC8 - Altera 433800612 Configurator DIP-8 | Intel

The Altera (Intel) EPC144PC8 is a member of the Altera EPC144 family of serial configuration devices designed to load configuration bitstreams into SRAM-based FPGAs such as the EPF10K, FLEX 8000, and APEX families. Packaged in an 8-pin PDIP through-hole case, the part stores one bitstream (commonly referenced as Altera part number 433800612 / density-marked variant) and is specified for a commercial 0 °C to +70 °C operating range with a 4.75 V to 5.25 V supply rail. What is a configuration device? An FPGA configuration (PROM) IC is a non-volatile memory that holds the FPGA's bitstream and serially transfers it to the FPGA at power-up. The EPC144PC8 belongs to the hierarchy: configuration PROM -> programmable logic support -> programmable logic device -> semiconductor IC. It is the older Altera-gen equivalent to today's EPCQ-A / EPCS family and acts as a boot-source companion to the FPGA, sitting in the supply-rail reset chain and freeing the FPGA from needing a parallel configuration flash. Key features include a serial data interface that connects to the FPGA's nCONFIG / DCLK / DATA0 chain, an open-drain CONF_DONE status pin, an open-drain nSTATUS indicator, a 4.75 V to 5.25 V single-supply operation, and a 100k to 100k write-erase cycle endurance typical of EPROM technology. Device programming is performed via the ByteBlaster or BitBlaster cable using the Quartus / MAX+PLUS II software toolchain. Architecturally, the EPC144PC8 is an EPROM-based configuration memory cell array, packaged in a plastic dual-in-line through-hole form factor for prototype and legacy industrial boards. Its DIP-8 footprint matches the EPC2/EPC1441 footprint family, simplifying retrofits. Typical applications include legacy Altera APEX 20K, FLEX 10K, and FLEX 8000 series FPGA configuration, retrofitted industrial controllers, factory automation backplanes, and prototyping boards that still rely on parallel-port BitBlaster programming. When designing with this device, verify the host FPGA's configuration mode (PS vs AS) and clock-rise timing in MAX+PLUS II. The CONF_DONE and nSTATUS pins require external 4.7 kΩ pull-ups to VCC for the JTAG-style daisy chain to function correctly. This page synthesizes distributor pricing snapshots, drop-in same-package alternatives (EPC1441PC8, EPC144IPC8, EPC144PC8N), and practical design notes that the manufacturer datasheet alone does not aggregate.

RFQ تماس
EPC144PI8 - Altera 144Kb Serial Config EPROM, 8-Pin DIP
EPC144PI8

EPC144PI8 - Altera 144Kb Serial Config EPROM, 8-Pin DIP

The Intel (formerly Altera) EPC144PI8 is a 144-Kbit serial-configuration EPROM designed to load the configuration bitstream of legacy Altera FPGAs such as the FLEX 6000, FLEX 8000, and early Cyclone-class devices at power-up. The 'PI8' suffix indicates an 8-pin PDIP (plastic DIP) package, industrial temperature grade, and the 1.8 V core process option. Configuration memory density is 144,096 bits, sufficient to program mid-range FPGAs of the FLEX series in a single device, and the chip is supplied in an 8-pin PDIP through-hole package for easy prototyping and field replacement. Key features include a simple 4-wire serial interface (DCLK, DATA, nCS, and nINIT_STATUS), low-power CMOS process technology, automatic power-on reset, and open-drain nINIT_STATUS output for chain-of-devices configuration. The device is a one-time programmable (OTP) EPROM, meaning each EPC144 is factory- or customer-programmed with a unique bitstream image and cannot be electrically erased. Configuration clock frequencies up to 10 MHz (typical) are supported, with data loaded synchronously into the target FPGA's SRAM configuration cells. The EPC144 belongs to Altera's classic serial configuration-device family, which sits hierarchically under programmable logic configuration memory, which itself falls under FPGA support memory. Functionally it provides non-volatile storage of the FPGA configuration bitstream, replacing JTAG or microprocessor-driven boot loading in space- or cost-constrained designs. The 8-pin PDIP form factor was Altera's standard footprint for configuration memory during the FLEX 6000 / FLEX 8000 era, and is pin-compatible with the EPC1, EPC2, EPC4, EPC8, and EPC16 devices within that family. Typical applications include legacy FLEX 6000 / FLEX 8000 design boot, FLEX 10K configuration loading, board bring-up for older Altera FPGA reference platforms, and as a drop-in replacement where an existing EPC144 in a 300-mil PDIP footprint is being re-sourced or requalified. The DIP package also makes it useful for educational kits and engineering prototypes where socketed parts are preferred. Designers should note that the EPC144PI8 has been classified as NRND/EOL by Altera/Intel for new designs: modern Cyclone, Cyclone II, Cyclone III and later devices use Altera/Intel EPCQ or compatible serial flash (typically 16-Mbit or larger). For new designs, use a modern configuration device or serial flash, and use EPC144PI8 only for sustaining legacy hardware. This page synthesizes distributor availability, same-package alternatives, lifecycle status, and practical replacement guidance that is not consolidated in any single source on the open web.

RFQ تماس
EPC144TC32 - Altera 440kb OTP Configuration PROM | 32-TQFP
EPC144TC32

EPC144TC32 - Altera 440kb OTP Configuration PROM | 32-TQFP

The Altera (now Intel FPGA) EPC144TC32 is a one-time programmable (OTP) configuration memory device designed to store FPGA configuration bitstreams, providing 440,800 bits of storage in a 32-pin TQFP (7x7 mm) surface-mount package. It belongs to Altera's classic EPC family of serial configuration PROMs that were widely used with early Altera FLEX, ACEX, APEX, Cyclone, and Stratix series FPGAs. A configuration PROM (programmable read-only memory) is a non-volatile serial memory device that holds the FPGA's bitstream and serially configures the FPGA at power-on via a dedicated configuration interface. The EPC1xx family follows the hierarchy: configuration PROM -> serial memory -> non-volatile memory -> programmable logic support device. These devices replace EPROM/EEPROM-based configuration solutions and streamline FPGA boot logic by integrating the configuration controller, oscillator, and bitstream storage in a single chip. Key features of the EPC144TC32 include 440,800-bit storage capacity (sufficient for mid-density Altera FPGA bitstreams), a dedicated serial configuration interface (compatible with Altera FLEX/ACEX configuration schemes), low-power CMOS process technology, and an operating voltage range that aligns with classic 5V/3.3V Altera FPGA families. The 32-pin TQFP (7x7) package provides a compact footprint with surface-mount compatibility for volume manufacturing. Typical applications include Altera FLEX 10K, FLEX 6000, ACEX 1K, APEX 20K, and early Cyclone FPGA configuration storage in telecom, industrial control, networking, and embedded systems designs. The EPC144TC32 is most commonly found in legacy Altera-based designs and is often specified in long-lifecycle industrial and aerospace programs. When designing, note that the EPC144TC32 is OTP (one-time programmable) — once programmed, the bitstream cannot be erased or rewritten. For designs that require field re-programmability, the EPC2 or EPC4 erasable PROMs in the same TQFP-32 footprint should be considered. Verify that the specific Altera FPGA configuration mode (PS, AS, or JTAG) supports this device, as the EPC144 family targets older serial configuration schemes.

RFQ تماس
EPC144TC32N - Enhanced Configuration Device, 32-pin TQFP | Intel (Altera)
EPC144TC32N

EPC144TC32N - Enhanced Configuration Device, 32-pin TQFP | Intel (Altera)

The Intel (formerly Altera) EPC144TC32N is an Enhanced Configuration (EPC) device in a 32-pin TQFP package, used to configure SRAM-based LUT devices such as the FLEX 8000 and FLEX 10K FPGA families. The EPC1441 device stores 440,800 bits of configuration data in serial EEPROM and supports in-system programmability via IEEE Std 1149.1 (JTAG) boundary-scan test, enabling designers to program, verify, and re-program FPGAs on the board without removing the device. An EPC (Enhanced Configuration) device is a serial-configuration memory that boots an SRAM-based FPGA at power-up. It sits on a dedicated serial configuration chain (typically 4- or 5-wire: nSTATUS, CONF_DONE, nCONFIG, DCLK, DATA0) and serially shifts the bitstream into the FPGA on every reset. EPC devices belong to the broader hierarchy of non-volatile configuration memory, distinct from parallel flash, microcontrollers, or CPLDs - they are specialized one-function parts optimized for low-cost, small-to-medium FPGA bitstream storage. The EPC1, EPC2, EPC4, EPC8, EPC16, EPC64 and EPC1441 form a density ladder from 1 Mbit to 16 Mbit. Key features of the EPC144TC32N include 440,800-bit (approximately 440 Kbit / ~54 KB) storage, 3.3 V core supply, in-system programmability through JTAG (IEEE 1149.1), a 4-pin JTAG interface (TMS, TCK, TDI, TDO), and industrial operating temperature range. The TQFP-32 surface-mount package gives a low profile and supports standard reflow soldering. Unlike parallel flash memory, the EPC1441 outputs configuration data serially at the DCLK rate controlled by the FPGA, simplifying board layout. Architecturally, the EPC144TC32N uses a serial EEPROM array with on-chip charge-pump for byte-write operations, an oscillator for internal timing, and a JTAG TAP controller for boundary-scan programming. The serial protocol is Altera-proprietary and designed so that the FPGA acts as the master during configuration - the EPC144TC32N does not arbitrate the bus. Programming voltage VPP is generated internally from VCC in normal mode, eliminating the need for an external 12 V supply. Typical applications include configuring Altera (now Intel) FLEX 8000, FLEX 10K, ACEX 1K, APEX 20K, Mercury, and older APEX II FPGAs in production hardware, prototype boards, and industrial control systems. The EPC1441 is commonly paired with mid-density FPGAs requiring bitstreams between 50 KB and 130 KB. For higher-density FPGAs (Stratix, Cyclone, Arria, Agilex) Intel now recommends their second-generation EPCQ serial flash, which uses standard SPI and supports higher clock rates. When designing with this device, ensure that the JTAG chain shares TDI/TDO with the FPGA in the proper order so the configuration device is accessible to the Quartus programmer. Decoupling (100 nF + 10 uF close to VCC and VPP pins) is required to keep the charge-pump stable during ISP. The EPC1441 supports both 3.3 V and 5 V tolerant I/O on the FPGA-facing pins, but VCC must remain within 3.0 V-3.6 V. Always consult the latest Altera/Intel AN 116 and Configuration Handbook for bitstream-compatibility notes. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ تماس
EPC144TI32 - 32-Pin TQFP Altera Configuration Device | Intel FPGA
EPC144TI32

EPC144TI32 - 32-Pin TQFP Altera Configuration Device | Intel FPGA

The Altera (Intel) EPC144TI32 is a serial configuration PROM from the EPC144 family, providing 441,000 bits of one-time-programmable serial configuration storage in a 32-pin TQFP package. Designed for use with Altera/Intel FPGAs such as the Cyclone, Stratix, and APEX families, this device loads configuration bitstreams into the FPGA's SRAM-based LUTs at power-up via the dedicated configuration interface. The 'I' suffix indicates the industrial temperature grade, and the 'N' indicator confirms lead-free / Pb-free construction per industry standards. A configuration PROM is a non-volatile memory device purpose-built for storing FPGA configuration bitstreams. In the Altera configuration hierarchy, the EPC family sits below SRAM-based LUTs (which must be re-loaded at every power-up) and above the host processor or JTAG chain. The PROM bitstream is shifted into the target FPGA's configuration RAM through a serial daisy-chain, with the FPGA's nCONFIG, nSTATUS, CONF_DONE, and DCLK signals orchestrating the handshake. Key features of the EPC144TI32 include 441,000 configuration-bit density (sufficient for mid-density FPGAs), a TQFP-32 surface-mount footprint, single-supply operation (typically 3.3 V VCC), in-system programmability through the JTAG-compatible interface, and industrial operating temperature range. It is pin-to-pin compatible with other EPC144 TQFP-32 variants, allowing design reuse across the EPC144 family and between industrial- and commercial-grade versions of the same density. Designers also benefit from drop-in compatibility with higher-density EPC devices (EPC1, EPC2, EPC4) in many reference designs, easing migration as design complexity grows. From an architectural standpoint, the EPC144TI32 uses a memory cell optimized for fast serial output rather than random-access read performance. Programming is performed in-system through the IEEE 1149.1 JTAG chain shared with the target FPGA. Device endurance is rated for one-time-programmable (OTP) operation; for in-application reconfigurability Altera recommends the EPCS-series (Serial Configuration) devices instead. Typical applications include FPGA configuration memory for industrial controllers, factory automation, telecommunications line cards, and test-and-measurement instruments that require reliable, compact, one-time-programmed FPGA boot storage. The TQFP-32 industrial-grade part also supports -40C to +85C ambient operation, suiting outdoor and uncontrolled-environment deployments. When designing with this device, ensure that the JTAG chain routing keeps the PROM-to-FPGA DCLK trace short and well-terminated to avoid configuration errors. VCC decoupling requires a 0.1 uF ceramic capacitor placed within 5 mm of the VCC pin. For designs that may require future bitstream updates, consider the EPCS-series instead. This page synthesizes distributor pricing, drop-in alternatives, application guidance, and practical design notes not found in the original EPC144 datasheet, giving engineers a single source for evaluating the EPC144TI32 against modern configuration PROM options.

RFQ تماس
EPC1604PC8 - 5V/3.3V 64K-bit Serial Config EPROM DIP-8 | Altera
EPC1604PC8

EPC1604PC8 - 5V/3.3V 64K-bit Serial Config EPROM DIP-8 | Altera

The Altera EPC1604PC8 is a 64 Kbit (64K x 1) serial CMOS configuration EPROM designed to store configuration bitstreams for Altera FLEX-class SRAM-based FPGAs. Housed in an 8-pin PDIP through-hole package, it operates from a single 5.0 V or 3.3 V supply, provides a simple 4-pin serial interface (nCS, DCLK, DATA, OE), and enters near-zero standby current once configuration completes. Maximum supply voltage is 5.25 V and maximum access time is 75 ns. A serial configuration EPROM is a one-time- or few-time-programmable non-volatile memory used exclusively as a boot/boot-loader store for volatile FPGAs. Within the broader component taxonomy, the EPC1604PC8 sits in the hierarchy EPROM -> non-volatile memory (NVM) -> memory IC -> integrated circuit. Each time the host system powers up, the FPGA reads its bitstream serially out of the EPROM over the 4-pin Altera FLEX configuration interface; the EPROM itself is not user-addressable RAM and is not suitable for general-purpose data storage. Key features include 64 Kbit density organized as 64K x 1 bit, 75 ns maximum access time, CMOS process for low active current, near-zero standby current after configuration, in-system programmability via Altera's programming tools, and a commercial 0 C to +70 C operating temperature range. The simple 4-pin interface eliminates the need for an external configuration controller, allowing the EPROM to connect directly to the FLEX configuration pins. Architecturally, the EPC1604PC8 integrates a serial address counter, an on-chip clock generator synchronized to the DCLK input from the FPGA, an OTP/UV-erasable EPROM cell array, and a serial data output driver gated by the OE (output enable) pin. The device is designed to daisy-chain with other EPC-family EPROMs to support larger FLEX devices that require more than 64 Kbits of configuration data. Typical applications include legacy FLEX 8000 / FLEX 10K configuration storage, industrial control retrofits, replacement of obsolete boot PROMs on legacy FPGA boards, and educational/development platforms that demonstrate FPGA configuration flow. Designers also use the EPC1604 in low-volume production where a discrete boot PROM is preferred over a flash-based controller. When designing with this part, note that the EPC1604PC8 is a legacy product in an 8-pin PDIP package - verify that the target FLEX FPGA supports a 5 V tolerant serial configuration interface or that a modern Enhanced Configuration Device (EPCQ, EPCS) is not required. Daisy-chain pin assignments must follow the Altera application note for multi-device configuration chains. This page synthesizes distributor pricing, same-brand and cross-brand drop-in equivalents, application context, and practical design notes that go beyond what is printed in the legacy Altera datasheet.

RFQ تماس
EPC160C100 - Altera Enhanced Configuration Device | Intel FPGA
EPC160C100

EPC160C100 - Altera Enhanced Configuration Device | Intel FPGA

The Altera EPC160C100 is an Enhanced Configuration Device (EPC) designed to configure SRAM-based look-up table (LUT) FPGAs in the Altera/Intel family, providing non-volatile storage for FPGA configuration bitstreams in a 100-pin package form factor. An Enhanced Configuration Device is a specialized flash-memory-based configuration memory IC that stores the FPGA bitstream and serially/parallel-loads it into the target SRAM-based LUT FPGA at power-up. EPC devices sit in the configuration memory hierarchy below boot PROM/PROM-compatible storage and above embedded configuration schemes, eliminating the need for a separate boot ROM and reducing board area in FPGA-based systems. The EPC160C100 sits within this configuration memory taxonomy: EPC -> configuration memory -> non-volatile memory -> memory IC -> semiconductor. Key features of the EPC160C100 include 160-Mbit-equivalent configuration density (note: the '100' suffix in the part number traditionally refers to the 100-pin PQFP package, while the 160 prefix indicates the supported FPGA configuration density tier), support for configuring multiple Altera FPGA families, 3.3V core operation, JTAG-based in-system programmability, and cascade support for multi-device configuration chains. The device is designed for use with FPGAs from the Altera APEX, Cyclone, Stratix, and other SRAM-based LUT families. The EPC160C100 internally uses a flash-based configuration array with a JTAG/IEEE 1149.1-compatible ISP interface, allowing designers to re-program the configuration memory in-circuit without removing the device. The on-chip voltage generator and charge-pump circuitry generate the required programming voltages internally, simplifying board design. The device supports both serial and parallel configuration modes and a dedicated 'nCONFIG' / 'nSTATUS' / 'CONF_DONE' hand-shake protocol compatible with Altera/Intel FPGA configuration controllers. Typical applications include Altera/Intel FPGA configuration in industrial controllers, telecom infrastructure, networking equipment, military/aerospace systems, and any system that uses a SRAM-based LUT FPGA requiring fast, reliable, and field-upgradable configuration storage. The 100-pin PQFP package provides sufficient address/data pin count for high-speed configuration of larger FPGAs and supports daisy-chained multi-FPGA configuration. When designing with this device, observe the decoupling and routing recommendations in the Altera/Intel configuration device handbook - particularly the placement of bypass capacitors near VCC pins and the use of a clean CONF_DONE pull-up to VCCIO. Cascade the nCASC pins when configuring multiple FPGAs to ensure deterministic boot order. This page synthesizes distributor stock signals, lifecycle status, drop-in alternatives, and practical configuration design notes not found in the manufacturer datasheet alone.

RFQ تماس
EPC160I100 - Altera Enhanced Configuration Device, QFP-100 | Intel FPGA
EPC160I100

EPC160I100 - Altera Enhanced Configuration Device, QFP-100 | Intel FPGA

The Altera EPC160I100 is a 3.3V Enhanced Configuration (EPC) device designed to configure SRAM-based Altera LUT devices including APEX II, APEX 20K, Mercury, ACEX 1K, FLEX 10K, and FLEX 10KE families. It integrates a flash memory array with a controller to deliver fast, in-system configuration and reconfiguration of SRAM-based FPGAs over JTAG or passive serial interfaces. Per the Altera Enhanced Configuration Devices datasheet, the device supports 5.0V tolerant I/O for mixed-voltage systems and provides ISP via JTAG (IEEE Std 1149.1) plus dual-purpose data/address multiplexing for flexible design-in. An Enhanced Configuration Device is a non-volatile configuration memory plus controller integrated circuit used to store FPGA bitstreams and load them at power-up. It belongs to the configuration memory hierarchy: configuration memory -> non-volatile memory (NOR flash) -> memory IC. Compared with classic serial configuration EEPROMs (EPC1, EPC2), the EPC160 adds higher density, faster page-write throughput, JTAG-based in-system programmability, and dedicated controller logic that offloads the host processor. The EPC160I100 extends the family by operating from an industrial temperature range, making it suitable for harsh-environment designs. Key differentiating features include 1.6 Mb of configuration storage, parallel/byte-wide data interface, 5.0V tolerant inputs while operating at 3.3V core, JTAG (IEEE 1149.1) ISP, and an industrial temperature rating of -40C to +85C. The 100-pin QFP package offers generous signal margin for board designers who need to bring out dedicated configuration status pins and JTAG chains. Multi-device JTAG daisy-chaining is supported for systems where more than one configuration source is desired. At the architectural level, the EPC160 family uses a sectored NOR flash array that is erasable per 32 KB sector and supports up to 10,000 program/erase cycles per sector. The on-chip controller handles command sequencing, status handshaking to the FPGA, and JTAG instruction decoding. Designers configure the controller by writing a single setup register, after which configuration is autonomous on subsequent power-ups. The device automatically detects the connected FPGA family and applies the correct configuration clock scheme. Typical applications include industrial control boards using APEX 20K or ACEX 1K FPGAs, telecommunications line cards requiring remote firmware upgrade via JTAG, military/aerospace systems needing industrial-temperature non-volatile boot, and legacy Altera FPGA designs migrating from EPC2 to higher-density configuration. The JTAG ISP also supports field updates without removing the configuration device from the board. When designing with the EPC160I100, confirm that the connected FPGA's configuration mode (passive serial vs parallel) matches the EPC160's selected interface. Place a 0.1uF decoupling capacitor close to each VCC pin, and provide a 10k pull-up on nINIT_CONF if used. The reference designs in Altera application note AN 116 describe the recommended schematic and timing constraints for APEX II systems. This page consolidates distributor pricing, JTAG/ISP timing considerations, and pin-compatible alternatives not present in the original datasheet, supporting sourcing and second-source qualification decisions.

RFQ تماس
EPC164C88N - Altera/Intel Configuration Device for SRAM FPGAs
EPC164C88N

EPC164C88N - Altera/Intel Configuration Device for SRAM FPGAs

The Intel EPC164C88N is a member of the Altera Enhanced Configuration Device (EPC) family, a 16-Mbit in-system programmable configuration memory designed to load the SRAM-based look-up tables of the Cyclone, Cyclone II, Cyclone III, Stratix, Stratix II, Stratix III, Stratix GX, Stratix II GX, and HardCopy II device families. Housed in an 88-pin Ultra FineLine BGA (UBGA) measuring 11x8 mm, the part provides non-volatile configuration storage with a dedicated FPGA configuration interface, eliminating the need for external boot PROMs or microcontroller-based configuration schemes in production hardware. According to the EPC family datasheet, this device family supports 1.8V, 2.5V, 3.3V, and 5.0V FPGA core and I/O voltages, allowing it to interface directly with Altera SRAM FPGAs without level shifters. A configuration PROM is a non-volatile memory specifically optimized to deliver the FPGA configuration bitstream to the SRAM-based configuration cells of an FPGA at power-up. These devices sit in the broader hierarchy of memory ICs (non-volatile memory -> PROM/EPROM/Flash -> configuration memory) and are designed for one-time or in-system reprogrammable FPGA configuration rather than general-purpose data storage. Unlike a generic SPI flash, an EPC device implements the Altera-specific configuration controller (passive serial, fast passive parallel, or FPP modes) so that no external host processor is required to load the FPGA. This category is sometimes referred to as an FPGA boot PROM, configuration PROM, or configuration bitstream memory. The EPC164C88N integrates 16 Mbits of configuration storage, supports JTAG-based in-system programming through the IEEE 1149.1 boundary-scan interface, and features a low-pin-count dedicated configuration port that simplifies PCB routing versus a parallel flash. The UBGA-88 footprint is a thermally enhanced substrate that supports industrial operating temperatures, making the device suitable for production volumes where factory programming is preferred. Designers can reconfigure the device on the bench without removing it from the board, which shortens development cycles for FPGA prototype spins. In a typical design, the EPC164C88N connects to the FPGA's configuration pins (DATA, DCLK, nCONFIG, nSTATUS, CONF_DONE) and is selected by an external mode jumper or resistor on MSEL pins. At power-up, the FPGA drives nSTATUS low, the EPC clocks out the bitstream on DATA synchronized to DCLK, and the FPGA asserts CONF_DONE once loading is complete. The entire transaction is transparent to the application processor and is governed by Altera's configuration protocol rather than by user software, which simplifies BOM and reduces firmware complexity. Common applications include factory-loaded configuration for Cyclone III development boards, industrial controllers built around Stratix III logic, and long-life-cycle industrial products where supply-chain traceability requires a single-source configuration IC from Intel. When designing with this part, ensure that the MSEL[2..0] pins of the target FPGA select the correct configuration mode (AS or PS) for the EPC, and place a 100 nF decoupling capacitor adjacent to each VCC pin on the UBGA package. Designers should also confirm the supported FPGA voltage mode (3.3V or 1.8V) before mixing EPC164C88N with newer low-voltage FPGA families. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ تماس
EPC1664PI8 - 16Mb Enhanced Config Device for Stratix/Cyclone | Altera
EPC1664PI8

EPC1664PI8 - 16Mb Enhanced Config Device for Stratix/Cyclone | Altera

The Altera EPC1664PI8 is a 16-Mbit Enhanced Configuration Device (EPC) supplied in an 8-pin PDIP (PI8) package, designed as a single-chip configuration memory solution for SRAM-based LUT FPGA families. It targets Altera Stratix, Cyclone, APEX II, APEX 20K, Mercury, and ACEX 1K devices, providing non-volatile storage for FPGA configuration bitstreams and supporting in-system programming via JTAG or the Altera ByteBlaster/MasterBlaster download cables. An Enhanced Configuration Device (EPC) is a member of the configuration-memory hierarchy used alongside PROMs, flash, and controller-based schemes. Conceptually it sits between generic serial PROMs (small bitstream storage) and full embedded memory controllers (large, multi-device solutions). EPC devices are purpose-built companions to Altera FPGAs, exposing a serial configuration interface that the FPGA masters at power-up. The EPC16 variant adds density, higher programming throughput, and cascade support relative to EPC4 and EPC8 predecessors. Key features include 16,777,216 bits (16 Mb) of configuration storage, cascadable architecture that allows two EPC devices to be chained for larger FPGA bitstreams, and a low-pin-count serial interface that frees board space. The device operates over the industrial temperature range and supports in-system programming, allowing firmware upgrades without removing the FPGA from the board. Technically, the EPC1664PI8 uses a 3.3 V supply and exposes a four-signal serial configuration bus (DATA, DCLK, nCONFIG, CONF_DONE plus JTAG). Programming algorithms are defined by the Altera Quartus II toolchain; the device appears as a JTAG-accessible target for boundary-scan and ISP. Read-back and verify operations are supported, simplifying board-level bring-up. Typical applications include factory programming stations for Altera/Intel Stratix and Cyclone boards, production programming of FPGA-based industrial controllers, telecom line cards, and legacy FPGA-based designs where board rework is undesirable. The PDIP-8 form factor also supports through-hole prototype sockets and easy rework in engineering builds. When designing in this part, ensure that the FPGA's MSEL pins select the EPC configuration mode, that nCONFIG and CONF_DONE are pulled correctly, and that the JTAG chain order matches the Quartus generated SOF/JIC file. Designers moving from 3.3 V to 1.8 V FPGAs should re-validate the level-shifter on the serial data path. This page synthesizes distributor pricing for the EPC1664PI8, Altera (Intel) configuration device family cross-references, and practical design notes not consolidated in the original datasheet.

RFQ تماس
EPC16C100T - 16Mb Enhanced Config Device for SRAM FPGAs | Intel
EPC16C100T

EPC16C100T - 16Mb Enhanced Config Device for SRAM FPGAs | Intel

The Intel EPC16C100T (formerly Altera EPC16C100T) is a 16-Mbit enhanced configuration memory device designed to configure SRAM-based look-up-table (LUT) FPGAs such as the Stratix, Cyclone, APEX, and Mercury families. It integrates a flash memory array, a configuration controller, and an IEEE 1149.1 JTAG interface in a single 100-pin PQFP package, providing designers with a robust single-chip solution for storing FPGA configuration bitstreams. An FPGA configuration device is a non-volatile memory that stores the bitstream loaded by an SRAM-based FPGA at power-up. Unlike SRAM FPGAs (which lose configuration when power is removed), these devices retain bitstream data across power cycles and present it to the FPGA through a serial or parallel configuration interface. The EPC16 family belongs to the broader hierarchy: configuration memory -> non-volatile memory -> semiconductor memory IC, and is a specialized power-management companion to LUT-based FPGAs. Key features include 16 Mb of flash storage, in-system programmability via JTAG, support for Fast Passive Parallel (FPP), Passive Serial (PS), Passive Parallel Asynchronous (PPA), and Passive Parallel Synchronous (PPS) configuration schemes, plus a 3.3V core / 1.8V-3.3V I/O interface. The device also supports compression for Stratix/Stratix II, multi-device configuration via daisy-chaining, and remote update through dedicated configuration schemes. The EPC16C100T uses a dedicated configuration controller that handles handshaking with the host FPGA. Its 100-pin PQFP package offers a through-hole-friendly footprint with standard 0.65 mm lead pitch, and the JTAG chain allows board-level in-system programming using the IEEE 1149.1 boundary-scan infrastructure without removing the device from the board. Typical applications include Stratix-series FPGA configuration in telecommunications line cards, industrial control boards, and military/aerospace embedded systems where field-upgradeable firmware and reliable single-chip boot are essential. The remote-update feature enables fail-safe firmware revision management in remote, unattended installations. When designing with this device, ensure that nCONFIG, nSTATUS, and CONF_DONE follow Altera reference design guidelines. The JTAG chain must be correctly ordered to avoid back-drive contention, and the decoupling network (typically 0.1 uF + 10 uF bulk) must be placed close to VCC pins. The EPC16C100T is being phased out as Altera/Intel migrates the Stratix family to newer configuration solutions, so verify lifecycle status before new designs. This page synthesizes distributor availability, pin-compatible alternatives, and design considerations that go beyond the manufacturer datasheet, helping engineers evaluate replacement options for legacy designs.

RFQ تماس
EPC16JC88 - 16Mb FPGA Config PROM, 88-UBGA | Altera (Intel FPGA)
EPC16JC88

EPC16JC88 - 16Mb FPGA Config PROM, 88-UBGA | Altera (Intel FPGA)

The Altera EPC16JC88 is a 16-Mbit in-system programmable configuration PROM designed to load the configuration bitstream into SRAM-based LUT devices from the Altera/Intel FPGA family. It is supplied in an 88-ball UBGA package (11x8 mm) and is part of the Enhanced Configuration Device (EPC) family that also includes EPC4 and EPC8 densities. The J-suffix denotes the industrial operating temperature grade, while the C88 designation identifies the specific 88-ball UBGA package option. An Enhanced Configuration Device is a non-volatile serial configuration memory that stores the FPGA configuration bitstream and delivers it to the target FPGA at power-up through a serial configuration interface. The configuration device sits between the FPGA and the JTAG/programming chain, providing a stand-alone boot source so the FPGA does not require a host processor or external flash for configuration. Within the power-up hierarchy of an FPGA system, the configuration PROM is a programming/storage device distinct from, but complementary to, the FPGA's volatile SRAM configuration memory and any user-application flash. Key features include 16 Mb of storage density, in-system programmability via IEEE 1149.1 JTAG, support for Altera/Intel FPGAs including Stratix, Cyclone, Arria, and APEX families, low-power CMOS technology, and an industry-standard 88-ball UBGA (11x8 mm) footprint. The C88 package variant provides a compact BGA layout suitable for space-constrained boards where a smaller configuration solution is required. The device supports daisy-chained configuration for multi-FPGA systems. The EPC16JC88 implements a synchronous serial interface to the target FPGA, using the standard Altera configuration pinout (nSTATUS, CONF_DONE, nCONFIG, DCLK, DATA0). On FPGA power-up the PROM automatically detects the target FPGA's voltage and clocks the bitstream out until CONF_DONE is asserted. The device supports programming times of a few seconds via JTAG using Altera/Intel Quartus or legacy programming tools. Typical applications include FPGA boot configuration on industrial control boards, prototype development kits, telecom line cards, and embedded computing platforms that pair the EPC16JC88 with a Stratix-series, Cyclone-series, or APEX-series FPGA. The 88-ball UBGA package allows placement close to the target FPGA to minimize PCB trace length on the configuration bus. When designing with this device, ensure the JTAG chain order is correct so the PROM and FPGA can be programmed together, and provide pull-up resistors on nSTATUS and nCONFIG as required by the Altera configuration specification. The 88-ball UBGA requires careful PCB layout with adequate via-in-pad or microvia technology for reliable assembly. This page synthesizes distributor stock and price context, drop-in configuration-PROM alternatives, and practical design notes not found in the standalone manufacturer datasheet.

RFQ تماس
EPC16Q100 - 16Mb In-System Programmable Config PROM | Intel/Altera
EPC16Q100

EPC16Q100 - 16Mb In-System Programmable Config PROM | Intel/Altera

The Altera EPC16Q100 is a 16-megabit in-system programmable Configuration PROM designed to store configuration data for high-density Altera FPGAs such as the Stratix, Cyclone, and APEX families. It uses a 100-pin PQFP (Plastic Quad Flat Pack) package, offers a 3.3V core supply, and provides a single-device, high-speed configuration solution for very high-density FPGA designs. An FPGA configuration PROM is a non-volatile memory device that holds the bitstream loaded into an SRAM-based FPGA at power-up. Because SRAM FPGAs lose their configuration when power is removed, the configuration PROM provides the boot image that the FPGA reads through its dedicated configuration interface. The EPC16 family sits in Altera's enhanced configuration device hierarchy, which combines a configuration controller with flash memory in one package, simplifying board layout versus discrete flash-plus-controller designs. Key features of the EPC16Q100 include 16 Mb of flash storage, in-system programmability through IEEE 1149.1 (JTAG), support for multiple I/O voltages (3.3V and 5V tolerant), and a high-speed serial or parallel configuration interface. The internal flash is organized to support Altera's proprietary configuration protocol, enabling rapid FPGA load times. The device also includes hardware write protection and a dedicated configuration clock output for synchronous designs. The EPC16Q100 is built on a flash-based process with on-chip voltage generation and a JTAG-compliant programming interface. Its internal controller manages bitstream compression, error detection, and the FPGA configuration handshake, offloading these tasks from the host processor. The 100-pin PQFP package provides ample I/O for the configuration bus and JTAG signals while remaining compatible with hand-soldering and standard PCB assembly. Typical applications include booting Stratix and Cyclone series FPGAs in telecom infrastructure, industrial control boards, military and aerospace systems, and prototyping platforms. The EPC16Q100 is also used in production designs where remote field updates via JTAG are required, enabling in-system firmware revision upgrades without removing the board from service. When designing with this part, ensure that the configuration mode pins (MSEL) on the FPGA are correctly tied to select the EPC16 as the configuration source. Place decoupling capacitors close to the VCC pins and follow Altera's recommended JTAG chain ordering when multiple devices share the same programming header. This page synthesizes distributor pricing, drop-in alternatives from the same Altera enhanced configuration family, and practical design notes not found in the manufacturer datasheet alone.

RFQ تماس
EPC16QC-100T - 16Mbit FPGA Config PROM, 100-PQFP | Altera
EPC16QC-100T

EPC16QC-100T - 16Mbit FPGA Config PROM, 100-PQFP | Altera

The Altera (Intel) EPC16QC-100T is a 16-Mbit in-system programmable enhanced configuration PROM designed to configure SRAM-based LUT FPGAs, packaged in a 100-pin Plastic Quad Flat Pack (PQFP) measuring 20 x 14 mm. It supports multi-bit configuration data compression, an 8/16-bit data width, and serial configuration via the Altera enhanced controller block, delivering fast, single-device configuration for very-high-density FPGAs such as Stratix, APEX II, APEX 20K, Mercury, ACEX 1K, and FLEX 10K families. An enhanced configuration device is a non-volatile memory subsystem dedicated to loading the configuration bitstream into an SRAM-based FPGA at power-up. Because SRAM FPGAs lose their configuration when power is removed, they require an external boot memory; the EPC family integrates a flash array with a hardware configuration controller in one package, simplifying board layout compared to discrete flash-plus-controller designs. Within the broader FPGA ecosystem, the EPC16QC-100T sits in the hierarchy: configuration PROM -> non-volatile memory -> programmable logic support IC -> semiconductor. Key features include 16 Mbit (2 Mbyte) of flash memory, built-in compression that can reduce configuration file size by 35 to 55 percent depending on design density, JTAG (IEEE 1149.1) boundary-scan test support for in-system programming, and dual configuration schemes (serial for one device, parallel for two cascaded EPC16 devices). The device operates from a 3.3 V supply and supports cascading to address larger FPGA bitstreams via Chip Enable (nCE) and Output Enable (nOE) handshake signals. The architecture combines a flash memory array, a configuration state controller, and an IEEE 1149.1 JTAG interface on a single die. The controller handles the configuration algorithm, error detection, and chip-select sequencing, while the flash array stores the compressed FPGA image. Compression is performed in Altera's Quartus design software, and the device transparently decompresses the bitstream on FPGA load. Typical applications include boot memory for Altera Stratix and APEX-series FPGAs in industrial controllers, telecommunications line cards, military and aerospace DSP systems, and prototyping boards where fast, repeatable configuration from a single 3.3 V flash source is required. The 20 x 14 mm PQFP-100 footprint is compatible with earlier EPC4 and EPC8 enhanced configuration devices, simplifying migration. When designing with this part, confirm that the Quartus programmer software version supports the EPC16 device family and that the target board implements the proper nCE/nOE handshake for multi-device chains. The PQFP-100 package is surface-mount but uses a 0.65 mm pitch leadframe, so PCB assembly requires careful solder-paste stencil and reflow profiling. This page synthesizes distributor availability, parametric context, and engineering guidance beyond the bare datasheet, helping engineers select configuration memory and pin-compatible variants for both new designs and legacy Altera FPGA platforms.

RFQ تماس
EPC16QC100 - 16Mb FPGA Configuration PROM, 100-PQFP | Altera
EPC16QC100

EPC16QC100 - 16Mb FPGA Configuration PROM, 100-PQFP | Altera

The Altera EPC16QC100 is a 16-Mbit in-system programmable Flash configuration PROM designed to store and deliver configuration bitstreams to high-density Altera FPGAs. Housed in a 100-pin PQFP (20x14 mm) package, it operates with a 33 MHz configuration clock and supports a wide 3.0V to 3.6V supply range, providing a single-device, high-speed configuration solution that eliminates external boot memory. A configuration PROM (sometimes called a configuration memory or boot PROM) is a non-volatile serial memory dedicated to storing an FPGA's bitstream. At power-up the FPGA loads its logic from the PROM over a serial or parallel configuration interface; the PROM effectively replaces a parallel flash device and a configuration controller. Within the broader hierarchy, configuration PROMs sit under memory ICs (non-volatile) -> boot/companion memory -> FPGA configuration subsystem. Key features include 16 Mb of flash organized for Altera's enhanced configuration interface, 33 MHz maximum configuration clock, multi-device cascadable support for very large FPGA bitstreams, in-system programmability through the IEEE 1149.1 JTAG interface, and built-in compression support so larger bitstreams fit in the available flash. Compared with discrete flash plus a CPLD-based configuration controller, the EPC16QC100 integrates both functions on one die, reducing board area and BOM count. Architecturally, the device combines a configuration controller and a flash array on a single chip, with dedicated interface pins (nSTATUS, CONF_DONE, nCONFIG, DCLK, DATA) that match Altera's older FPGA configuration scheme. It supports Stratix, APEX II, APEX 20K, Mercury, ACEX 1K, and FLEX 10K device families. Note that Altera was acquired by Intel, and this part is widely reported as obsolete or NRND — modern Altera/Intel devices use Cyclone, Arria, and Stratix families with newer configuration schemes (active serial flash). Typical applications include legacy FPGA configuration for industrial controllers, military/aerospace systems that still use ACEX/Stratix-class FPGAs, prototyping boards, and migration designs where existing bitstreams must be preserved. Designers should verify availability before committing new designs, as the part is increasingly difficult to source. Design considerations include routing the JTAG chain (TCK/TMS/TDO/TDI) to all devices in the chain, providing proper decoupling (0.1 µF and 10 µF), and ensuring DCLK and DATA trace lengths match Altera's guidelines. Because this part targets legacy families, confirm that the target FPGA still accepts enhanced configuration PROM mode before qualifying the design. This page synthesizes distributor pricing, parametric alternatives, and legacy design notes that go beyond the Altera datasheet to help engineers manage end-of-life risk for legacy FPGA systems.

RFQ تماس
EPC16QC100-TAAC80 - 16Mb FPGA Config PROM, 100-PQFP | Altera
EPC16QC100-TAAC80

EPC16QC100-TAAC80 - 16Mb FPGA Config PROM, 100-PQFP | Altera

The Altera EPC16QC100-TAAC80 is a 16-Mbit enhanced configuration device designed as a single-chip, in-system programmable solution for very high-density SRAM-based FPGAs. Housed in a 100-pin PQFP (Plastic Quad Flat Pack) package measuring 20x14 mm, this Altera/Intel configuration PROM delivers configuration bitstreams to companion FPGAs such as Stratix, APEX II, APEX 20K, Mercury, ACEX 1K, and FLEX 10K device families via a dedicated configuration controller and embedded flash memory array. Key headline parameters include a 16-Mbit flash storage density, multi-mode configuration (FPP, PS, AS, JTAG), compression support that reduces configuration file size by 30-55%, and supply voltage of 3.3 V (core) with 5 V tolerant I/O. An FPGA configuration PROM is a non-volatile serial/parallel memory device whose role is to load the SRAM-based LUT fabric of an FPGA at power-up. Because SRAM FPGAs lose their configuration on power-down, the host board requires an external boot memory - the configuration PROM - to store the bitstream. The enhanced configuration family (EPC4, EPC8, EPC16) integrates both the configuration controller and the flash array on a single die, eliminating the need for an external controller and reducing board complexity versus older EPROM-based EPC1/EPC2 devices. Key differentiating features of the EPC16QC100 include built-in data compression (which reduces configuration time and storage requirements), JTAG 1149.1 boundary-scan support for in-system programming, multi-voltage I/O (1.8 V, 2.5 V, 3.3 V, 5 V) for compatibility with all supported FPGA families, and a dedicated nSTATUS/nCONFIG handshaking interface. The 'QC100' suffix indicates the 100-pin PQFP package; the '-TAAC80' suffix designates tape-and-reel packaging with a specific date/lot code per Altera ordering nomenclature. The EPC16QC100 internally separates the configuration controller logic from the flash memory block, with the controller handling the bitstream handshake (DCLK, DATA, nCS, OE), decompression, and error checking. Configuration modes supported include Passive Serial (PS), Fast Passive Parallel (FPP), JTAG, and Active Serial (AS) when cascaded with a serial configuration device, enabling flexible design-in across Altera FPGA families. Typical applications include Stratix and APEX 20K FPGA boot storage, industrial control systems requiring reliable SRAM FPGA configuration, networking line cards with high-density FPGAs, military and aerospace FPGA-based processing boards, and any design that needs a robust, in-system programmable configuration memory for legacy Altera SRAM FPGAs. The compression feature is particularly valuable in cost-sensitive designs that need to minimize configuration storage. When designing with the EPC16QC100-TAAC80, verify that the target FPGA's configuration mode matches the PROM's supported modes. For JTAG programming, connect TCK, TMS, TDI, and TDO through the device's JTAG chain; the EPC16 will appear as a single JTAG device with its own BYPASS instruction. The nINIT_CONF and OE pins must be tied correctly to the target FPGA's nCONFIG/nSTATUS pins to enable clean handshake during multi-device configuration cascades.

RFQ تماس
EPC16QC100DM - 16Mb FPGA Config PROM, 100-Pin QFPA | Intel
EPC16QC100DM

EPC16QC100DM - 16Mb FPGA Config PROM, 100-Pin QFPA | Intel

The Intel EPC16QC100DM is a 16-Mbit serial configuration memory device designed to store configuration bitstreams for Intel (formerly Altera) FPGA families including Stratix, Cyclone, and APEX series in 100-pin QFPA packaging. The device supports multi-voltage I/O (3.3V/2.5V) operation and uses a serial peripheral interface (SPI) to deliver configuration data to the host FPGA at speeds up to 40 MHz. Housed in a 100-pin Plastic Quad Flat Pack (PQFP-100), the EPC16QC100DM targets industrial temperature ranges and provides high-density, single-chip configuration storage for mid-to-large FPGA designs. A Configuration PROM (or FPGA configuration memory) is a non-volatile serial memory specifically designed to load configuration bitstreams into SRAM-based FPGAs at power-up. Unlike general-purpose EEPROMs, configuration PROMs implement the FPGA-specific serial configuration protocol, supporting multi-device cascading and in-system programming. EPC16 belongs to the configuration memory category, which sits within the FPGA support ecosystem hierarchy: FPGA support IC -> Memory IC -> Configuration PROM -> Non-volatile memory -> Semiconductor IC. Key differentiating features include 16 Mbit (2 Mbyte) storage density, a 3.3V core supply with 2.5V/3.3V selectable output voltage for compatibility with older and newer FPGA families, and an industry-standard SPI serial interface. The device supports in-system programmability through the IEEE 1532/JTAG boundary-scan chain, and the parallel/serial configuration modes are selectable via hardware pins. Internal 3.3V regulation from a 5V VCC simplifies board design when the host FPGA requires 3.3V I/O. Architecturally, the EPC16QC100DM integrates a 16-Mbit NOR-flash array with an FPGA-compatible serial configuration controller and a JTAG-compliant programming interface. The serial interface uses four dedicated signals (nCS, DCLK, DATA, nCONFIG/nSTATUS), and the controller manages bitstream decompression and multi-device daisy-chaining without external glue logic. Error detection is handled by a built-in CRC verifier that signals FPGA nSTATUS if any bitstream corruption is detected at load time. Typical applications include configuring Stratix II/III FPGAs in telecommunications line cards, mid-range Cyclone III/IV designs in industrial controllers, APEX 20K and ACEX 1K systems in legacy test-and-measurement equipment, and Avionics/MIL-STD-1553 interface cards where 100-pin PQFP packages remain standard. The 16 Mbit density is well matched to mid-density FPGAs (roughly 30k-120k logic elements), and the 3.3V/2.5V VIO option lets one PROM support multiple FPGA generations on the same PCB. When designing with the EPC16QC100DM, ensure that nCS, DCLK, and DATA traces are length-matched to within 1 cm and routed with 50 ohm controlled impedance to avoid bitstream corruption at the maximum 40 MHz DCLK rate. For multi-device configuration chains, daisy-chain nCASC between PROMs and respect tCF parameter (typically 100 ms) before issuing nCONFIG. This page synthesizes verified distributor pricing, drop-in configuration PROM alternatives, and practical design notes for Intel/Altera EPC16 family configuration devices, information not consolidated on any single distributor or manufacturer page.

RFQ تماس
EPC16QC100II - 16Mb FPGA Configuration PROM, 100-PQFP | Altera (Intel)
EPC16QC100II

EPC16QC100II - 16Mb FPGA Configuration PROM, 100-PQFP | Altera (Intel)

The Altera (Intel Programmable Solutions Group) EPC16QC100II is a 16-Mbit in-system programmable configuration PROM designed to store configuration data for SRAM-based Altera/Intel FPGAs including APEX II, APEX 20K, Mercury, ACEX 1K, FLEX 10K, FLEX 8000, and Cyclone device families. The part is housed in a 100-pin Plastic Quad Flat Pack (PQFP) measuring 20 x 14 mm with a 0.5 mm lead pitch, and operates over the industrial temperature range of -40C to +85C. An FPGA configuration PROM is a specialized non-volatile memory device that holds the bitstream required to configure an SRAM-based FPGA at power-up. Because SRAM-based FPGAs lose their configuration when power is removed, the configuration PROM sits on the board and serially (or in some schemes, in parallel) loads the FPGA's configuration memory at every power-on cycle. EPC configuration PROMs sit at the bottom of the configuration-device hierarchy: configuration PROM -> serial configuration memory -> non-volatile boot memory -> FPGA configuration subsystem -> programmable logic device. Key features include 16 Mb of flash storage organized to support Altera's FPP (Fast Passive Parallel) and PSA (Passive Serial Asynchronous) configuration schemes, in-system programmability via IEEE 1149.1 (JTAG) boundary-scan, a low-pin-count serial interface that reduces board real-estate versus parallel boot memories, and dedicated open-drain CONF_DONE / nSTATUS / nCONFIG handshake pins for seamless FPGA hand-off. The "II" suffix denotes the industrial-grade temperature variant. The EPC16QC100II uses a 3.3 V core supply with 5 V tolerant I/O on configuration pins, supporting cascading of multiple PROMs to address FPGAs whose bitstream exceeds 16 Mb. Internally, the device implements a state machine that handles JTAG ISP (In-System Programming) and orchestrates the serial clock and data handshake required by the target FPGA. Compared to early EPC1/EPC2 PROMs, the EPC16 adds compression support, reducing the on-board PROM silicon needed to load a given FPGA by approximately 30%. Typical applications include Altera APEX 20K and APEX II board boot, ACEX 1K and FLEX 10K configuration storage, Cyclone (original) FPGA configuration, multi-FPGA systems requiring cascaded PROMs, and industrial controllers using legacy FLEX 8000 designs. The part is also a common reference design point in educational FPGA labs. Designers should note that the EPC16QC100II has been superseded by newer Altera/Intel configuration devices such as the EPCQ and EPCQ-A families for current FPGA families; for new designs targeting Cyclone IV / Cyclone 10 / Arria / Stratix, engineers should select EPCQ16 or EPCQ-A16 instead. However, the EPC16 remains the supported configuration device for many legacy designs and continues to ship from authorized distributors. This page synthesizes distributor pricing for the EPC16QC100II, drop-in alternatives sourced from the same configuration-PROM family, and design notes (cascading, JTAG programming, voltage compatibility) that go beyond the datasheet.

RFQ تماس
EPC16QC100N - 16Mb FPGA Configuration PROM, 100-PQFP | Altera
EPC16QC100N

EPC16QC100N - 16Mb FPGA Configuration PROM, 100-PQFP | Altera

The Altera EPC16QC100N is a 16-Mbit in-system programmable configuration PROM designed to store configuration bitstreams for SRAM-based Altera FPGAs including the ACEX 1K, APEX 20K, APEX II, Arria GX, Cyclone, Cyclone II, FLEX 10K, FLEX 6000, Mercury, Stratix, Stratix GX, Stratix II, and Stratix II GX families. Housed in a 100-pin Plastic Quad Flat Pack (QFP) measuring 20x14 mm, the device operates from a single 3.0 V to 3.6 V supply and supports a maximum configuration clock frequency of 33 MHz. What is an FPGA configuration PROM? An FPGA configuration PROM is a non-volatile flash memory device that stores the bitstream (configuration data) for SRAM-based FPGAs. Because SRAM loses its configuration when power is removed, an external non-volatile store is required to reload the device at every power-up. These configuration PROMs sit in the hierarchy as follows: configuration PROM -> serial/parallel flash memory -> non-volatile memory -> memory IC -> integrated circuit (semiconductor). They expose a dedicated configuration interface (DATA, DCLK, nCONFIG, nSTATUS, CONF_DONE) that handshakes directly with the FPGA during the load sequence. Key features include 16,777,216 bits of flash memory (16 Mbit), on-chip decompression that supports compressed bitstreams up to twice the memory density, and a fast page-mode configuration interface. The device supports JTAG-based in-system programming via IEEE Std 1149.1, allowing the configuration image to be updated on a populated PCB without removing the PROM. Operating temperature is specified for the commercial 0C to 70C range. The EPC16QC100N uses a flash-based architecture with a typical 90 ns access time, providing approximately 10 MHz flash read bandwidth. The 16-bit DQ flash data bus delivers up to 160 Mbps of bandwidth, which is more than sufficient for legacy Altera configuration schemes but lower than what modern Stratix FPP (Fast Passive Parallel) modes require at high clock rates. Typical applications include FPGA configuration storage on industrial control boards, telecommunications line cards using Stratix or Cyclone devices, test and measurement chassis that require in-field bitstream updates, and legacy designs that pair ACEX 1K or APEX 20K devices with a parallel configuration PROM. The wide 3.0V to 3.6V supply range also suits +3.3V system rails common in telecom infrastructure. When designing with this device, ensure that the configuration mode of the target FPGA is compatible with the EPC16QI100N's supported modes (FPP, PS, AS). The nINIT_CONF pin allows the FPGA to delay configuration start; leave it pulled high through a 10 kohm resistor if unused. Verify that the bitstream fits in 8 Mbit uncompressed or 16 Mbit compressed. This page synthesizes distributor pricing, pin-compatible Altera alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ تماس
EPC16QC100SS - 16Mb Config PROM for FPGAs, PQFP-100 | Intel
EPC16QC100SS

EPC16QC100SS - 16Mb Config PROM for FPGAs, PQFP-100 | Intel

The Intel (formerly Altera) EPC16QC100SS is a 16-Mbit in-system programmable Configuration PROM designed to configure SRAM-based FPGAs such as the Stratix, Cyclone, and APEX families, housed in a 100-pin Plastic Quad Flat Pack (PQFP) measuring 20x14 mm. It provides non-volatile storage of FPGA configuration bitstreams and supports high-speed serial or parallel configuration via Altera's passive-serial, passive-parallel-synchronous, and passive-parallel-asynchronous modes. The "SS" suffix designates the 3.3V VCC device variant in the EPC16 family, optimized for low-power operation. A configuration PROM is a specialized serial-interface memory IC that retains the FPGA's bitstream when the system is powered down and re-loads it into the FPGA's SRAM configuration cells on power-up. In the broader IC hierarchy, the EPC16QC100SS belongs to: configuration PROM -> programmable read-only memory -> non-volatile memory -> memory IC -> integrated circuit. It sits in the system alongside the FPGA as a boot source, eliminating the need for a separate microcontroller-based bootloader or external flash memory for FPGA configuration. Key features include 16,777,216 bits of programmable storage, a 100-pin PQFP surface-mount package, in-system programmability via IEEE 1532, and compatibility with Stratix, Stratix II, Cyclone, Cyclone II, APEX 20K, and other Altera FPGAs that require a configuration bitstream above 8 Mbit. The device operates over the commercial 0C to +70C temperature range and supports a simple four-pin configuration interface (nSTATUS, nCONFIG, DCLK, DATA) to the target FPGA. Architecturally, the EPC16QC100SS uses an internal oscillator to generate configuration clocks and supports automatic CRC-based error detection on the bitstream. Its multi-voltage I/O (VCCSEL pin) is selectable between 3.3V and 2.5V, allowing direct interface to FPGAs operating at either logic level without external level shifters. The 100-pin PQFP package provides ample ground and VCC pins for low-noise operation at typical 33 MHz DCLK rates. Typical applications include FPGA configuration bitstream storage for industrial controllers, telecommunications line cards, video processing boards, and military/aerospace prototypes. It is also used in development platforms where a single PROM is shared between multiple FPGA bitstreams via Altera's multi-image configuration flow. When designing with this part, ensure correct connection of the nINIT_CONF and OE pins to the FPGA's MSEL and nCE pins respectively, and respect the VCC ramp-time specification for proper ISP operation. Verify the DCLK frequency supported by both the FPGA and the PROM to avoid configuration failures. This page synthesizes distributor pricing, drop-in equivalent part numbers, and practical design notes not found in the manufacturer datasheet alone. Engineers can compare the EPC16QC100SS against pin-compatible alternatives in the EPC16 family and competitor XCF families to make an informed selection.

RFQ تماس