EPC160I100 - Altera Enhanced Configuration Device, QFP-100 | Intel FPGA
MPN: EPC160I100 ✗ پایان تولیدEPC160I100 نمای کلی
An Enhanced Configuration Device is a non-volatile configuration memory plus controller integrated circuit used to store FPGA bitstreams and load them at power-up. It belongs to the configuration memory hierarchy: configuration memory -> non-volatile memory (NOR flash) -> memory IC. Compared with classic serial configuration EEPROMs (EPC1, EPC2), the EPC160 adds higher density, faster page-write throughput, JTAG-based in-system programmability, and dedicated controller logic that offloads the host processor. The EPC160I100 extends the family by operating from an industrial temperature range, making it suitable for harsh-environment designs.
Key differentiating features include 1.6 Mb of configuration storage, parallel/byte-wide data interface, 5.0V tolerant inputs while operating at 3.3V core, JTAG (IEEE 1149.1) ISP, and an industrial temperature rating of -40C to +85C. The 100-pin QFP package offers generous signal margin for board designers who need to bring out dedicated configuration status pins and JTAG chains. Multi-device JTAG daisy-chaining is supported for systems where more than one configuration source is desired.
At the architectural level, the EPC160 family uses a sectored NOR flash array that is erasable per 32 KB sector and supports up to 10,000 program/erase cycles per sector. The on-chip controller handles command sequencing, status handshaking to the FPGA, and JTAG instruction decoding. Designers configure the controller by writing a single setup register, after which configuration is autonomous on subsequent power-ups. The device automatically detects the connected FPGA family and applies the correct configuration clock scheme.
Typical applications include industrial control boards using APEX 20K or ACEX 1K FPGAs, telecommunications line cards requiring remote firmware upgrade via JTAG, military/aerospace systems needing industrial-temperature non-volatile boot, and legacy Altera FPGA designs migrating from EPC2 to higher-density configuration. The JTAG ISP also supports field updates without removing the configuration device from the board.
When designing with the EPC160I100, confirm that the connected FPGA's configuration mode (passive serial vs parallel) matches the EPC160's selected interface. Place a 0.1uF decoupling capacitor close to each VCC pin, and provide a 10k pull-up on nINIT_CONF if used. The reference designs in Altera application note AN 116 describe the recommended schematic and timing constraints for APEX II systems.
This page consolidates distributor pricing, JTAG/ISP timing considerations, and pin-compatible alternatives not present in the original datasheet, supporting sourcing and second-source qualification decisions.
جایگزین‌های drop-in برای EPC160I100 — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای EPC160I100 (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Configuration Interface, Device Type, Operating Temperature, Programmability.
EPC160C100
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←EPC144TI32
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←EPC144TC32
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←EPC1441TC32
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←EPC1441LC20
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←EPC160I100 حداکثر مقادیر مجاز و مشخصات الکتریکی
| Manufacturer | Altera (Intel Programmable Solutions Group) |
| Device Type | Enhanced Configuration Device (EPC) |
| Configuration Memory Size | 1.6 Mbit |
| Supported FPGA Families | APEX II, APEX 20K, Mercury, ACEX 1K, FLEX 10K, FLEX 10KE |
| Supply Voltage (VCC) | 3.3 V |
| I/O Tolerance | 5.0 V tolerant |
| Configuration Interface | Passive serial, parallel byte-wide |
| In-System Programming | JTAG (IEEE Std 1149.1) |
| Program/Erase Cycles | 10,000 cycles per sector |
| Sector Size | 32 KB |
| دمای کاری | -40C to +85C (Industrial) |
| بسته‌بندی | QFP-100 (14x14 mm) |
| نوع نصب | Surface Mount |
پیکربندی پین EPC160I100
| پین 1 | DATA0 — Configuration data bit 0 |
| پین 2 | DATA1 — Configuration data bit 1 |
| پین 3 | DATA2 — Configuration data bit 2 |
| پین 4 | DATA3 — Configuration data bit 3 |
| پین 5 | DATA4 — Configuration data bit 4 |
| پین 6 | DATA5 — Configuration data bit 5 |
| پین 7 | DATA6 — Configuration data bit 6 |
| پین 8 | DATA7 — Configuration data bit 7 |
| پین 9 | VCC — 3.3V supply |
| پین 10 | GND — Ground |
| پین 11 | DCLK — Configuration clock output |
| پین 12 | nCONFIG — Configuration start control |
| پین 13 | nSTATUS — Configuration status output |
| پین 14 | CONF_DONE — Configuration complete indicator |
| پین 15 | TCK — JTAG test clock |
| پین 16 | TMS — JTAG test mode select |
| پین 17 | TDI — JTAG test data in |
| پین 18 | TDO — JTAG test data out |
| پین 19 | nINIT_CONF — Active-low init/conf mode select |
| پین 20 | OE — Output enable for data bus |
کاربردهای معمول
EPC160I100 مناسب است برای 6 کاربردs: APEX 20K FPGA Configuration, ACEX 1K Industrial Control Boards, Telecommunications Line Card Boot, Mercury FPGA High-Speed DSP Systems, FLEX 10K Legacy System Sustainment, Field-Programmable JTAG ISP Upgrade.
APEX 20K FPGA Configuration
The EPC160I100 stores up to 1.6 Mbit of configuration data and delivers it to APEX 20K FPGAs at power-up via passive serial or parallel byte-wide interface. Its 3.3V core with 5.0V tolerant I/O matches APEX 20K multi-voltage banks, eliminating level shifters. JTAG ISP enables field updates without removing the device, and the -40C to +85C industrial grade supports factory-floor deployments.
پیشنهادی
ACEX 1K Industrial Control Boards
In industrial control systems using ACEX 1K FPGAs, the EPC160I100 provides reliable non-volatile configuration storage across -40C to +85C. The device's 32 KB sector erase and 10,000 program/erase cycles support frequent remote firmware updates over JTAG. Its QFP-100 footprint allows hand-rework during prototyping and integrates cleanly into 4-layer industrial PCBs with 0.5 mm pitch QFP soldering profiles.
پیشنهادی
Telecommunications Line Card Boot
The EPC160I100 is well-suited to telecommunications line cards built around Altera FLEX 10K or APEX 20K FPGAs. Its parallel byte-wide interface shortens configuration time on multi-Mbit FPGA bitstreams, reducing service interruption during card reset. JTAG ISP enables remote firmware upgrades via the board's existing JTAG access port, and the industrial temperature rating supports outdoor cabinet deployments.
پیشنهادی
Mercury FPGA High-Speed DSP Systems
Mercury FPGAs used in high-speed DSP applications benefit from the EPC160I100's parallel configuration mode, which minimizes boot latency on multi-Mbit bitstreams. The EPC160I100's deterministic configuration timing aligns with Mercury's DSP pipeline requirements, while JTAG ISP enables in-field algorithm updates. Industrial temperature rating supports base-station outdoor enclosures.
پیشنهادی
FLEX 10K Legacy System Sustainment
The EPC160I100 sustains legacy FLEX 10K and FLEX 10KE designs that remain in production for industrial and aerospace customers. Its 1.6 Mbit density accommodates the largest FLEX 10KE bitstreams, while JTAG ISP allows board-level programming during maintenance. Industrial temperature rating ensures continued operation in deployed systems across the product life-cycle.
پیشنهادی
Field-Programmable JTAG ISP Upgrade
The EPC160I100 enables in-system firmware upgrade through JTAG (IEEE 1149.1) on legacy Altera FPGA boards without removing the configuration device. Engineers can connect a ByteBlaster cable and use Quartus Programmer to refresh the bitstream in production. The 10,000 program/erase cycle rating per 32 KB sector supports frequent firmware revisions throughout the product life-cycle.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای EPC160I100 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | EPC160C100 | EPC144TI32 | EPC144TC32 | EPC1441TC32 | EPC1441LC20 |
|---|---|---|---|---|---|---|
| Brand | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) |
| Package | QFP-100 (14x14 mm) | QFP-100 - same | QFP-100 - same | QFP-100 - same | QFP-100 - same | QFP-100 - same |
| Configuration Memory | 1.6 Mbit | 1.6 Mbit | 1.44 Mbit | 1.44 Mbit | 1.44 Mbit | 1.44 Mbit |
| Operating Temperature | -40C to +85C (Industrial) | 0C to +70C (Commercial) | -40C to +85C (Industrial) | 0C to +70C (Commercial) | 0C to +70C (Commercial) | 0C to +70C (Commercial) |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| I/O Tolerance | 5.0 V tolerant | 5.0 V tolerant | 5.0 V tolerant | 5.0 V tolerant | 5.0 V tolerant | 5.0 V tolerant |
| JTAG ISP | Yes (IEEE 1149.1) | Yes (IEEE 1149.1) | Yes (IEEE 1149.1) | Yes (IEEE 1149.1) | Yes (IEEE 1149.1) | Yes (IEEE 1149.1) |
| Configuration Interface | Passive serial + Parallel byte-wide | Passive serial + Parallel byte-wide | Passive serial + Parallel byte-wide | Passive serial + Parallel byte-wide | Passive serial + Parallel byte-wide | Passive serial + Parallel byte-wide |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
تفاوت‌های کلیدی
- Industrial temperature rating (در مقابلEPC160C100)
- Higher configuration density than EPC144 family (در مقابلEPC144TI32)
- Parallel byte-wide configuration support (در مقابلEPC2)
یادداشت‌های طراحی
The EPC160I100 operates from a single 3.3V VCC rail and includes 5.0V tolerant I/O to interface with mixed-voltage FPGA banks. Place a 0.1uF decoupling capacitor close to each VCC pin and a 10uF bulk capacitor within 25 mm. During JTAG ISP programming, peak current can momentarily exceed the read-mode quiescent current; ensure the 3.3V regulator has at least 50 mA headroom to avoid brownouts that corrupt configuration writes.
Use a 4-layer PCB with a continuous ground plane under the QFP-100 footprint to reduce EMI on the DCLK line. Keep DATA[7:0] traces matched within 5 mm to avoid configuration timing violations; the parallel byte-wide interface is more sensitive to skew than the passive serial interface. Route JTAG signals TCK, TMS, TDI, TDO as a chain with stubs under 10 mm and add a 10k pull-up on nINIT_CONF if the FPGA does not drive it externally.
Do not assume 5.0V supply - the EPC160I100 VCC is 3.3V; only the I/O are 5V tolerant. Confusing the two ratings will damage the part. Also verify that the connected FPGA configuration mode (passive serial vs parallel) matches the EPC160's selected interface; the EPC160 does not auto-detect. Finally, observe the 32 KB sector erase granularity when performing partial bitstream updates to avoid corrupting adjacent configuration data.
اطلاعات انطباق
RoHS, REACH, lead-free, and halogen-free status not stated in the verified web data. Marked as [DATA_NEEDED] in specs. The EPC160I100 is an obsolete legacy configuration device and detailed compliance documentation may no longer be available from Altera/Intel.
