محصولات (46,000+)

ICS341MP - 200MHz Spread Spectrum Clock Synth | Renesas
ICS341MP

ICS341MP - 200MHz Spread Spectrum Clock Synth | Renesas

The Renesas Electronics ICS341MP is a low-cost, single-output, field-programmable clock synthesizer with a maximum output frequency of 200 MHz and an LVCMOS output in an 8-pin SOIC package. It accepts a clock or crystal input, contains one PLL, and supports programmable output frequencies from 250 kHz to 200 MHz at a 1:1 input-to-output ratio. A field-programmable clock synthesizer is a clock-and-timing IC that generates a stable digital clock from an external reference. The ICS341 belongs to the broader PLL-based frequency synthesizer hierarchy, where the PLL multiplies or divides a reference frequency to create a programmable operating clock. Clock-and-timing ICs support digital systems requiring deterministic frequency generation, clock distribution, or reduced electromagnetic interference. The ICS341MP supports spread-spectrum clock generation to reduce system EMI by distributing clock energy over a range of frequencies. Its maximum frequency is 200 MHz, while its minimum programmable output is 250 kHz. A single LVCMOS output simplifies clock routing, and the integrated PLL allows the device to operate from a clock or crystal reference. These characteristics suit designs that need adjustable timing without a complex multi-output clock architecture. The ICS341MP is implemented in an 8-SOIC surface-mount package measuring 3.90 mm in body width. This package provides a practical upgrade over larger through-hole clock devices while remaining compatible with conventional PCB assembly. Its single-circuit architecture also keeps the signal path manageable, although applications requiring multiple independently programmable outputs would need a more capable clock generator. Typical uses include EMI-sensitive embedded systems, communications equipment, consumer electronics, and digital processing platforms where a programmable reference is useful. Spread-spectrum operation can help reduce narrowband emissions in systems that must meet internal or regulatory EMC goals. The 200 MHz ceiling supports common processor, interface, and control-clock requirements, while the 250 kHz lower limit accommodates lower-rate digital buses and control logic. Designers should verify the reference-input configuration, programmed frequency range, output enable behavior, and external crystal or clock requirements against the manufacturer datasheet before layout. Keep the reference and output paths short, provide the required decoupling capacitors close to the device, and confirm that the selected spread-spectrum range satisfies both timing margins and system EMC objectives. This page organizes the ICS341MP specifications, sourcing information, design guidance, and qualified drop-in options into one engineering-focused reference. It supports faster part selection while emphasizing the need to validate programming, reference, and EMC details against the manufacturer datasheet.

RFQ تماس
ICS342MP - 200MHz Dual-Output Clock Synthesizer | Renesas
ICS342MP

ICS342MP - 200MHz Dual-Output Clock Synthesizer | Renesas

Renesas Electronics ICS342MP is a field-programmable, dual-output clock synthesizer with a maximum output frequency of 200 MHz, packaged in an 8-pin SOIC. The device accepts clock or crystal input and provides LVCMOS clock outputs through an integrated PLL architecture. Its specified 3.15 V to 3.45 V operating-supply range makes it suitable for low-voltage digital systems requiring locally generated, configurable timing signals. A clock synthesizer is a clock and timing IC that generates, divides, multiplies, or redistributes clock signals for digital logic. Clock generators and PLL-based synthesizers belong to the broader timing-control hierarchy that includes oscillators, clock buffers, dividers, and jitter-cleaning devices. Unlike a crystal oscillator, which primarily produces a fixed reference frequency, the ICS342MP uses programmable synthesis to produce multiple related output clocks and reduce the number of separate timing components in a system. The ICS342MP combines two configurable outputs with PLL support and a maximum frequency of 200 MHz. Its input section can operate from a clock or crystal, while its LVCMOS outputs are suited to digital logic that requires single-ended clock signals. The SOIC-8 surface-mount package also supports conventional PCB assembly and provides a compact option for communication, control, and embedded-system clock trees. Programmability allows the output frequencies to be selected through the device configuration interface instead of requiring a separate fixed-frequency oscillator for each clock domain. This can simplify board partitioning and provide a common timing reference for related circuits. The PLL architecture is useful when the system needs an output frequency derived from a common reference, although loop behavior, output jitter, and reference stability must be evaluated during clock-tree design. Typical uses include digital controller timing, industrial automation modules, embedded processor clock distribution, communications equipment, and general-purpose peripheral clocking. In these systems, two outputs can support related clock domains or distribute a master clock to two loads while keeping the design compact. The low-voltage supply requirement should be checked against the voltage and sequencing requirements of the logic being clocked. The main design consideration is preserving signal integrity between the synthesizer outputs and receiving logic. Keep clock traces short, provide a continuous ground reference, use appropriate termination when required, and observe the input and output timing limits in the manufacturer datasheet. Decoupling should be placed close to the supply pin, with the value and stability requirements taken directly from the recommended application circuit. This page consolidates the ICS342MP device identity, clock-synthesis specifications, package information, sourcing structure, and application-oriented design guidance. It also identifies the verified same-family replacement candidate and separates confirmed electrical attributes from parameters that require confirmation before schematic release or production qualification.

RFQ تماس
ICS343MP - 200MHz Triple-Output Clock Synthesizer | Renesas
ICS343MP

ICS343MP - 200MHz Triple-Output Clock Synthesizer | Renesas

Renesas Electronics ICS343MP is a field-programmable, triple-output clock synthesizer based on the VersaClock architecture. It generates three independently programmable output clocks, reaches a maximum output frequency of 200 MHz, and accepts either a crystal or external clock input. The device is packaged in an 8-pin SOIC measuring 3.90 mm wide, making it suitable for compact communications, industrial control, test-and-measurement, and embedded timing systems. A clock synthesizer is a timing IC that accepts a reference frequency and uses one or more phase-locked loops to produce stable, independently configurable clock outputs. The ICS343 belongs to the clock generator and PLL hierarchy within the broader clock and timing IC category. Its three-output architecture can replace multiple discrete oscillators or divider networks when a board requires several related frequencies from one reference source. The ICS343MP provides three programmable outputs, PLL-based frequency synthesis, LVCMOS output signaling, and maximum frequency operation of 200 MHz. Separate output divide values from 2 through 20 allow the output clock banks to support widely different frequencies from the same reference. These features make the device useful where a system needs flexible clock partitioning without allocating a separate synthesizer for every rail. Its architecture supports low-cost field-programmable clock generation from a crystal or clock source. Independent output programming is particularly valuable in mixed-signal, communications, and data-conversion systems where the processor, serial interface, and peripheral blocks may not require the same frequency. The 8-SOIC package also offers a familiar surface-mount footprint for designs that must support external oscillators or frequency dividers. Typical applications include processor and interface clocking, communications modules, industrial automation equipment, test and measurement instrumentation, and embedded control systems. In each case, the synthesizer can centralize reference distribution while allowing output frequencies and divide ratios to be selected during configuration. The result is a smaller clock tree and potentially fewer discrete timing components. Designers should evaluate loop bandwidth, output jitter, supply requirements, and board-level noise using the manufacturer's application guidance before high-volume release. Reference-crystal layout, grounding, and output-routing practices are especially important in low-jitter systems. Because output-edge quality depends on the complete clock tree, PCB trace geometry and supply decoupling should be evaluated together with the programmed divider and PLL settings. This product page consolidates the device classification, functional characteristics, sourcing information, and engineering-oriented usage guidance. It also distinguishes the verified ICS343MP configuration from related suffix variants and identifies the limitations of the available replacement records, helping engineers make a more informed drop-in decision without treating broadly similar clock ICs as electrically interchangeable.

RFQ تماس
ICS345RP - Triple PLL 200MHz Clock Synthesizer | Renesas
ICS345RP

ICS345RP - Triple PLL 200MHz Clock Synthesizer | Renesas

Renesas Electronics ICS345RP is a triple-PLL field-programmable clock synthesizer IC with a 200 MHz maximum clock frequency and up to nine high-quality, high-frequency clock outputs, including multiple reference clocks. The device is supplied in a 20-SSOP package with a 3.90 mm package width, making it suitable for compact embedded clock-generation designs where several independently derived clock signals are required. A field-programmable clock synthesizer is a clock and timing IC that uses one or more phase-locked loops to generate, divide, multiply, or otherwise derive multiple clock outputs from a reference source. In the broader semiconductor hierarchy, a PLL belongs to the clock and timing category and provides a flexible alternative to fitting separate oscillators and divider networks on a complex circuit board. The ICS345RP is positioned for systems that need multiple related clock domains while preserving a centralized programming and distribution architecture. The ICS345RP combines a triple-PLL architecture with field-programmable output generation. According to the Renesas datasheet result for the 345 family, the device can generate up to nine high-quality, high-frequency clock outputs and can derive those outputs from a low-frequency reference. The verified distributor listing identifies the ICS345RP as a clock/frequency synthesizer IC with a 200 MHz frequency rating and a single 20-SSOP configuration. This type of device is useful in communication equipment, industrial control systems, test and measurement instruments, embedded computing platforms, and other systems requiring multiple clocks with predictable relationships. A common design uses a stable reference source at the input and programmable divider, multiplier, and phase-alignment functions to create the required output frequencies. The central benefit is reduced component count and easier clock-tree management compared with several unrelated oscillator and divider combinations. When designing around the ICS345RP, confirm the reference frequency, target output frequencies, output-routing requirements, and permitted programming scheme against the manufacturer datasheet. The 20-SSOP footprint requires careful PCB layout, particularly around supply decoupling, clock output routing, and grounding. The package should not be replaced with a mechanically similar part unless its pinout, programming model, PLL performance, and output-routing behavior have been verified. This page summarizes the verified device identity, package, frequency, PLL, and output-count information while highlighting the practical clock-tree role of the ICS345RP. Detailed electrical limits, pin assignments, programming registers, and application-specific replacement decisions should be confirmed in the Renesas ICS345 documentation before schematic sign-off or PCB release.

RFQ تماس
ICS348RP - 200MHz Quad-PLL Clock Synthesizer | Renesas
ICS348RP

ICS348RP - 200MHz Quad-PLL Clock Synthesizer | Renesas

The Renesas ICS348RP is a quad-PLL field-programmable VersaClock synthesizer that generates up to nine high-quality, high-frequency clock outputs from a crystal or external clock input. Its maximum clock frequency is 200 MHz, and the device provides LVCMOS clock outputs in a 20-pin QSOP/SSOP package. The ICS348RP belongs to the clock generator and frequency synthesizer family, combining phase-locked-loop frequency multiplication with programmable output generation. A clock generator is an integrated circuit that creates one or more timing references from a stable source. A frequency synthesizer extends this function by multiplying, dividing, or otherwise transforming a reference frequency. The ICS348RP places four PLLs and multiple output stages in one timing IC, allowing a system to distribute related reference and working clocks while avoiding a collection of separate oscillator and divider circuits. The ICS348RP supports a crystal or clock input, includes PLL bypass capability, and can produce as many as nine clock outputs. These characteristics make it useful where a board needs several coordinated frequencies for processors, memory, serial links, converters, or data-conversion equipment. Because the device is field programmable, system designers can configure output behavior rather than relying only on fixed factory frequencies. Its quad-PLL architecture provides the central mechanism for deriving multiple clock outputs from a common low-frequency reference. Maintaining a shared reference can simplify synchronization across subsystems and reduce the number of separate frequency-generation components. The bypass path is important during development because it provides a way to evaluate clock-source conditions without relying on every PLL operating at once. Typical applications include communications equipment, test and measurement instruments, industrial control systems, data-acquisition modules, and embedded computing platforms. The device is especially relevant when a design needs several related high-frequency outputs but has limited board space or wants to centralize clock generation in one programmable component. Layout should preserve short, controlled clock paths and place support components near their associated pins. Differential and high-speed routing requires careful return-path planning, while power and ground distribution should remain stable across the clock-generation domain. Designers should verify output frequency, jitter, phase relationship, and bypass behavior against the final system timing budget. This product page organizes the key clock-synthesis facts, package information, practical use cases, and engineering guidance for ICS348RP. It also highlights the distinction between electrical substitutes and package-only order-code variants so procurement and design teams can evaluate compatibility correctly before making an engineering change.

RFQ تماس
ICS348RPT - 200MHz Quad PLL Clock Synthesizer | Renesas
ICS348RPT

ICS348RPT - 200MHz Quad PLL Clock Synthesizer | Renesas

Renesas Electronics ICS348RPT is a quad-PLL field-programmable VersaClock synthesizer with a maximum output frequency of 200 MHz, LVCMOS outputs, and support for clock or crystal inputs. The device is packaged in a 20-pin QSOP for surface-mount production and operates across a 0°C to 70°C temperature range. It belongs to the clock and timing hierarchy of semiconductor ICs, where clock synthesizers generate, multiply, divide, and distribute reference clocks for digital and analog systems. A PLL-based clock synthesizer is a timing IC that locks an internal oscillator to an external reference and then produces one or more programmable clock outputs. This architecture allows a system designer to derive multiple related frequencies from one reference source. The ICS348RPT combines four PLL channels with field-programmability, making it suitable for systems requiring multiple independently configurable clock domains and flexible output ratios. Key features include a 200 MHz maximum output frequency, four PLL outputs, PLL bypass capability, LVCMOS output logic, and clock or crystal input support. Its 20-terminal QSOP package measures 8.65 mm by 3.9 mm. The component uses CMOS technology, has a surface-mount mounting design, and carries a JESD-609 code of e0. Tape-and-reel packaging supports automated assembly and high-volume manufacturing. The ICS348RPT is a clock-generation and distribution device rather than a general-purpose timing controller. Its programmable output structure can be used to establish relationships among reference, feedback, and output clocks while maintaining a single-board reference architecture. Designers should compare frequency limits, input format, output logic level, programming interface, and package details before using it in a new design. Typical uses include communications equipment, test and measurement systems, industrial control electronics, and embedded digital platforms that need several derived clocks. In such systems, the quad architecture can reduce the number of separate oscillator and divider combinations while preserving central control of clock relationships. LVCMOS outputs are particularly useful when downstream receivers require a conventional single-ended clock interface. A critical design consideration is signal integrity. Route clock outputs over controlled-impedance traces, provide a continuous reference plane, and keep clock circuitry away from high-current switching paths. Decoupling should be placed close to the supply pins, and unused outputs should be terminated according to the receiver and board requirements. Validate source-to-endpoint timing and jitter margins on the final layout. This product page combines the manufacturer-level identity, confirmed package and timing characteristics, practical clock-tree design guidance, and a focused comparison of documented VersaClock family alternatives. Use the manufacturer datasheet for programming registers, electrical limits, recommended application circuits, and the authoritative pin-description table before completing a production design.

RFQ تماس
ICS409M - 80MHz PC Peripheral Clock | Renesas Electronics
ICS409M

ICS409M - 80MHz PC Peripheral Clock | Renesas Electronics

The Renesas Electronics ICS409M is a PC peripheral clock synthesizer with PLL capability, crystal input, LVCMOS output, and a maximum frequency of 80 MHz. It is packaged in an 8-pin SOIC and is designed to reduce external component count in PC peripheral clocking systems. The supported output ratio is 1:3, while one synthesizer circuit provides a compact clock-generation solution for compatible legacy PC applications. A clock synthesizer is a clock and timing integrated circuit that derives one or more stable output signals from a reference source. Within the hierarchy of oscillator, phase-locked loop, clock generator, timing IC, and semiconductor, the ICS409M uses an on-chip crystal oscillator and PLL to support PC peripheral clock requirements. This category is important when a system needs a defined frequency that differs from the original crystal reference. Key verified features include PLL support, crystal input, LVCMOS output, one clock circuit, a 1:3 input-to-output ratio, and operation up to 80 MHz. The 8-pin SOIC package supports conventional surface-mount PCB assembly. Its integration can reduce the number of discrete oscillator and divider components required around a PC peripheral interface. The verified source material describes the ICS409M as a cost-effective clock synthesizer optimized for PC peripheral applications. The device accepts a common 14.31818 MHz crystal through its on-chip crystal oscillator and uses the PLL to establish the required output relationship. This reference arrangement is relevant to legacy PC interfaces whose clock trees were designed around the widely used 14.31818 MHz frequency. The LVCMOS output is suitable for digital clock distribution when voltage levels, timing margins, and load requirements are confirmed in the original system design. Typical uses include PC peripheral timing, interface clock generation, frequency multiplication, and replacement of discrete crystal-oscillator and divider networks. Because the available verified data does not provide complete electrical limits or timing tables, engineers should consult the manufacturer datasheet and system clock requirements before release to production. The primary design consideration is compatibility. Confirm the crystal frequency, target output frequency, output duty cycle, supply voltage, load capacitance, and PCB footprint before substitution. A nominal 80 MHz maximum rating does not establish that every downstream timing requirement is met; system-level rise-time, jitter, and setup-and-hold margins remain decisive. This page consolidates verified distributor and technical-source information, package and frequency details, sourcing links, and practical replacement guidance that is not presented as a single consolidated manufacturer datasheet.

RFQ تماس
ICS409MLF - 80MHz LVCMOS PLL Clock Synthesizer | Renesas
ICS409MLF

ICS409MLF - 80MHz LVCMOS PLL Clock Synthesizer | Renesas

Renesas Electronics ICS409MLF is a PC peripheral clock synthesizer with a 14.31818 MHz crystal input, an integrated phase-locked loop, and a maximum output frequency of 80 MHz in an 8-pin SOIC package. The device generates a 1:3 input-to-output clock ratio and uses LVCMOS-compatible outputs to support low-cost PC peripheral clocking. A clock synthesizer is a timing IC that converts a lower-frequency reference into one or more system clock signals. Clock synthesizer, PLL clock generator, and frequency multiplier are related terms within the clock and timing IC hierarchy, which also includes clock buffers, dividers, oscillators, and timer ICs. The ICS409MLF is intended to reduce the number of discrete components required in personal-computer peripheral applications. The ICS409MLF supports a common 14.31818 MHz crystal through its on-chip crystal oscillator. Its PLL-based architecture multiplies the reference clock by three, producing an 80 MHz maximum output. The specified operating supply range is 3 V to 3.6 V, making the device suitable for systems using a 3.3 V clock domain. The principal technical benefit is integration: a crystal oscillator, phase-locked loop, and frequency-multiplying output are combined in one IC. This reduces the component count compared with discrete oscillator and multiplier arrangements. The single-circuit implementation also simplifies clock routing, although output drive, jitter, phase accuracy, and loop stability must still be evaluated against the timing requirements of the target peripheral. Typical applications include PC peripheral interfaces, legacy storage and bus controllers, embedded PC-compatible systems, and communication equipment requiring a 3.3 V LVCMOS reference clock. A 14.31818 MHz crystal is normally connected at the reference input, while the divided PLL architecture generates the higher-frequency clock used by the peripheral subsystem. When laying out the circuit, keep the crystal and load capacitors close to the device and route the clock output away from noisy switching nodes. Confirm ground-plane continuity, output-load assumptions, and the required clock frequency before releasing the layout. Pin assignments and crystal-load details should be taken directly from the manufacturer pin-description table and application guidance.

RFQ تماس
ICS409MT - 80MHz PC Peripheral Clock | Renesas Electronics
ICS409MT

ICS409MT - 80MHz PC Peripheral Clock | Renesas Electronics

Renesas Electronics ICS409MT is a clock and frequency synthesizer designed for PC peripheral applications. It uses an on-chip crystal oscillator with a 14.31818 MHz crystal input, provides one LVCMOS clock output, and supports output frequencies up to 80 MHz. The device is packaged in an 8-pin SOIC and operates across the 0°C to 70°C temperature range. Its 1:3 input-to-output ratio makes it suitable for systems that derive a higher-frequency operating clock from the common 14.31818 MHz reference used in PC architectures. A clock synthesizer is a timing IC that generates or distributes clock signals needed by digital logic. Clock generators and phase-locked loops sit within the clock and timing IC category, where they support processors, memory interfaces, communications equipment, and computer peripherals. By multiplying a stable reference frequency, the ICS409MT reduces the number of separate oscillators and distribution components required in a system while providing a defined LVCMOS interface for downstream circuitry. The principal features of the ICS409MT are its 80 MHz maximum output frequency, single LVCMOS output, single PLL, crystal input, and 1:3 input-to-output ratio. The 14.31818 MHz reference arrangement supports designs based on the traditional PC timing domain, while the on-chip oscillator eliminates the need for an external oscillator module. The 8-SOIC surface-mount package also supports compact, automated PCB assembly compared with larger through-hole clock packages. Technically, the ICS409MT is identified as a PLL-based clock and frequency synthesizer with one clock circuit. The oscillator and PLL establish the output timing relationship between the crystal reference and the LVCMOS clock output. The listed 1:3 ratio indicates that the output clock is three times the reference frequency, producing 42.95454 MHz when operated with a 14.31818 MHz crystal. Input and output polarity, PLL loop bandwidth, jitter, output duty-cycle limits, and detailed electrical timing values require confirmation from the manufacturer datasheet before final timing-budget work. Typical applications include PC peripheral clock generation, legacy computer interface cards, embedded systems that use a 14.31818 MHz reference, communication equipment, and digital subsystems requiring a locally generated LVCMOS clock. In these systems, the device can centralize clock multiplication and reduce oscillator-component count. Its 80 MHz ceiling provides useful headroom when the intended peripheral clock is 42.95454 MHz, while the single-output architecture suits designs that need one derived clock rather than several independently managed clocks. The primary design consideration is crystal and layout stability. Place the crystal, load capacitors, and ground path close to the device, and route high-current clock output away from sensitive analog and communication signals. Validate the resulting clock against the system’s frequency tolerance, jitter, rise-time, duty-cycle, and load requirements. Because the documented operating range is 0°C to 70°C, the part should not be assumed suitable for industrial temperature environments without additional qualification. This product record combines the device architecture, package information, operating limits, search-oriented technical questions, application guidance, and engineering-selection context. It also clearly separates confirmed characteristics from parameters that require datasheet confirmation, helping designers evaluate ICS409MT before committing it to a PC peripheral, legacy computing, or embedded clock-generation design.

RFQ تماس
ICS411M - PC Peripheral Clock | IDT | SOIC-8
ICS411M

ICS411M - PC Peripheral Clock | IDT | SOIC-8

The Integrated Device Technology ICS411M is a cost-effective PC peripheral clock synthesizer in an 8-SOIC package. The verified product data identifies it specifically for PC motherboard and peripheral applications, but does not provide a manufacturer-hosted technical datasheet. The component is therefore best characterized by its stated clock-generator role, legacy origin, package format, and reported distributor inventory rather than unsupported frequency, voltage, or timing claims. It belongs to the clock and timing IC hierarchy, where oscillators and clock synthesizers distribute timing signals used to coordinate digital logic. Its purpose in a personal computer was to support multiple peripheral buses or subsystem clocks while reducing the number of separate clock components required on the motherboard. An integrated clock synthesizer combines oscillator circuitry, frequency generation or distribution, and output-driver functions into one timing IC. Such devices help maintain defined relationships between digital signals. In computer systems, those relationships determine when processors, buses, storage controllers, and peripherals may exchange data. The ICS411M is described as a PC peripheral clock and is intended to optimize component count in PC motherboard and peripheral designs. Its 8-SOIC package provides a compact, surface-mount form suitable for legacy motherboard assembly, although physical dimensions and pin functions require confirmation from an authentic technical datasheet. The available evidence establishes three important procurement facts: ICS411M was originally associated with IDT, Integrated Device Technology Inc; it is packaged as 8-SOIC, listed with a nominal width of 3.90 mm; and distributor listings report inventory. However, the verified data does not state operating voltage, output count, supported clock frequencies, frequency tolerance, jitter, operating temperature, or pin assignments. Those values must not be inferred from similarly named clock ICs. This limitation is especially important because clock generators with the same package can differ substantially in pinout and output behavior. ICS411M is relevant when researching or maintaining older PC peripheral platforms rather than designing a new clock subsystem from first principles. Verified distributor listings include references to octopart clock buffers and drivers, but these search results do not establish a technical replacement or lifecycle recommendation. Before substitution, an engineer should compare the authentic ICS411M pinout, supply voltage, output waveform, frequency plan, enable logic, and timing margins. Octopart and the listed distributors can assist with sourcing, but manufacturer documentation remains the controlling source for design decisions. A typical legacy motherboard application would place the ICS411M among the system timing circuitry and route its outputs according to the original platform schematics. Because exact output assignments are unavailable in the verified data, PCB reuse cannot be approved from the package alone. Clock routing should remain short, reference planes should return cleanly, and unused outputs require the treatment specified by the original platform design. Modern replacements should not be assumed to be pin compatible. The key engineering caution is documentation completeness. Verify the original manufacturer or archived manufacturer datasheet before energizing, probing, or substituting ICS411M in powered equipment. Confirm device markings, supply rails, oscillator connections, and every package pin. This page deliberately distinguishes verified product identity from unverified technical assumptions and provides sourcing links, practical assessment guidance, and transparent data gaps for repair, maintenance, and legacy-system evaluation.

RFQ تماس
ICS411MLF - 25MHz PC Peripheral Clock | Renesas Electronics
ICS411MLF

ICS411MLF - 25MHz PC Peripheral Clock | Renesas Electronics

The Renesas Electronics ICS411MLF is a 25 MHz PC peripheral clock synthesizer packaged in an 8-pin SOIC surface-mount package. It operates from a 3 V to 3.6 V supply and is intended for personal-computer motherboard and peripheral clock applications. The device provides a cost-effective clock-generation solution designed to reduce the component count associated with distributing a common peripheral reference clock. A peripheral clock synthesizer is a type of clock and timing integrated circuit that generates or conditions a stable reference signal for digital subsystems. Clock generators and clock buffers sit within the broader clock-and-timing hierarchy, which supports synchronization, data transfer, and deterministic circuit operation in personal computers, communications equipment, and embedded systems. The ICS411MLF converts a system timing reference into the clock required by compatible PC peripheral functions. Key characteristics include a nominal output frequency of 25 MHz, a 3 V to 3.6 V operating supply range, and an 8-SOIC package compatible with standard surface-mount assembly. Its single-function architecture allows a motherboard or peripheral design to obtain a defined clock without implementing a general-purpose programmable oscillator. The 8-pin package also keeps the required PCB footprint compact while providing separate supply and clock-related connections. The ICS411MLF is intended for applications where a conventional, fixed-frequency clock source is sufficient and the design priority is component-count reduction. Its fixed 25 MHz output simplifies schematic design because the required frequency does not need to be programmed or adjusted during operation. The manufacturer describes the device as a cost-effective clock synthesizer for PC motherboard and peripheral applications, making it most appropriate for established platform architectures rather than new designs requiring programmable frequency, spread-spectrum modulation, or fractional-N synthesis. Typical uses include PC motherboard peripheral clock distribution, storage-controller clocking, interface-module clocking, and legacy peripheral systems operating from a 3.3 V rail. In these designs, the synthesizer supplies a common local reference while system-level oscillators or phase-locked loops establish the master timing hierarchy. Power-system design must still account for the device's 3 V to 3.6 V operating range and verify the output behavior against the load and trace requirements of the connected peripheral. The principal design consideration is compatibility with the target clock tree. Confirm the required frequency, supply voltage, output-load expectations, and board-level timing budget in the manufacturer datasheet before layout release. Route the clock output as a short, controlled-impedance trace and keep the supply return path close to the device so that the fixed 25 MHz reference reaches the load without unnecessary added noise or timing distortion. This page organizes the manufacturer and distributor information for the ICS411MLF into an engineering-oriented product record. It combines the 25 MHz clock function, supply range, 8-SOIC packaging, purchasing guidance, and design considerations so that engineers can evaluate the device quickly against motherboard and peripheral clock requirements.

RFQ تماس
ICS411MT - 25MHz LVCMOS PC Clock Generator | Renesas
ICS411MT

ICS411MT - 25MHz LVCMOS PC Clock Generator | Renesas

The Renesas Electronics ICS411MT is a PC peripheral clock synthesizer with PLL-based clock generation, an input clock interface, and LVCMOS output. It supports operation up to 25 MHz and contains one clock circuit in an 8-pin SOIC package. The device was developed as a cost-effective solution for PC motherboard and peripheral clock-distribution requirements, providing a compact alternative to discrete oscillator, divider, and buffer combinations. A clock generator is a timing IC that converts an input reference into one or more stable clock signals for digital systems. Clock synthesizers sit within the clock and timing IC family, where phase-locked loops (PLLs) can multiply, divide, or otherwise condition a reference frequency. Within a computer platform, the resulting clock can synchronize bus activity, interface circuits, peripheral controllers, and other logic that must operate from a common timing reference. Key characteristics of the ICS411MT include its PLL capability, clock input, LVCMOS output, maximum operating frequency of 25 MHz, and single-circuit architecture. These features make the part relevant to legacy PC motherboard and peripheral clocking where a compact integrated solution is preferred over multiple discrete timing components. Its 8-pin SOIC package also supports conventional surface-mount assembly and automated PCB production. Technically, the ICS411MT combines reference-clock conditioning with PLL-based frequency generation. A PLL synchronizes an output phase to a reference signal while permitting frequency synthesis through internal loop control. This architecture is useful when the board must derive a required operating clock from an available reference while maintaining a defined relationship between input and output. The manufacturer datasheet is the controlling document for loop bandwidth, jitter, operating limits, pin functions, and electrical characteristics. Typical applications include PC motherboard clock generation, peripheral interface timing, clock distribution for legacy computer logic, and replacement of discrete oscillator-and-divider networks. The device can also serve systems in which one LVCMOS clock domain must be reproduced for multiple downstream circuits. Board designers should verify timing margins, output drive, supply requirements, and all enable or feedback connections against the manufacturer datasheet before production. The primary design consideration is to treat the clock as a high-speed signal even though its maximum frequency is only 25 MHz. Route the output with a short, controlled-impedance path, keep the reference and output returns connected to a common ground plane, and place decoupling capacitors close to the supply pins. Avoid unnecessary stubs and test-probe loops that can degrade edge quality or introduce reflections. This page consolidates the verified clock-generator specifications, package information, sourcing workflow, pinout status, and engineering guidance for ICS411MT evaluation. It also distinguishes documented functionality from parameters that must be confirmed in the manufacturer datasheet, helping engineers assess fit before committing to a PCB or production release.

RFQ تماس
ICS477R-05 - 74.175MHz Quad PLL VCXO | Renesas Electronics
ICS477R-05

ICS477R-05 - 74.175MHz Quad PLL VCXO | Renesas Electronics

Renesas Electronics ICS477R-05 is a 74.175 MHz quad phase-locked-loop clock generator with a voltage-controlled crystal oscillator, packaged in a 28-pin SSOP. It generates five high-quality, high-frequency clock outputs, including two reference outputs, from a low-frequency pullable crystal. The device is designed to replace multiple discrete crystals and crystal oscillators in electronic systems requiring coordinated, low-jitter timing. A phase-locked loop is a feedback-controlled timing circuit that locks a high-frequency oscillator to a stable reference. The ICS477R-05 adds VCXO functionality, allowing the frequency of a crystal oscillator to be adjusted within a limited range by an external control voltage. In the clock and timing hierarchy, this product is a PLL-based clock generator with a voltage-controlled crystal reference. The ICS477R-05 operates from a 3.15 V to 3.45 V supply and accepts a crystal reference while producing LVCMOS clock outputs. Its quad-PLL architecture supports five outputs, which can simplify systems that previously required several independent oscillators or output dividers. The 28-SSOP surface-mount package also supports compact HDTV and related digital-video equipment. The key benefit of integrating the PLL, crystal control, and five clock outputs into one device is reduced component count and centralized timing. Unlike a free-running clock generator, the PLL architecture is intended to derive multiple related frequencies from a common pullable crystal. This arrangement is particularly useful when the system requires several outputs with defined phase relationships for video processing, communications, or synchronization. Typical applications include HDTV master-clock generation, digital video timing, broadcast equipment, crystal-oscillator consolidation, and clock-tree replacement in electronic systems. The device can reduce the number of discrete frequency sources while providing one controllable reference network. Its 74.175 MHz operating point is particularly relevant to video timing architectures associated with high-definition television systems. The primary design consideration is clock quality. PCB placement, crystal selection, loop filtering, supply decoupling, and output-load configuration can affect phase noise, jitter, and output stability. Use the pin-description and application information in the Renesas datasheet when assigning tracks and selecting the pullable crystal and its associated load network. This product page consolidates the device architecture, operating limits, lifecycle information, package details, replacement-family options, and practical clock-design guidance into one engineering reference for evaluating the ICS477R-05.

RFQ تماس
ICS487G-25 - 48MHz Quad PLL Clock Generator | Renesas Electronics
ICS487G-25

ICS487G-25 - 48MHz Quad PLL Clock Generator | Renesas Electronics

The Renesas Electronics ICS487G-25 is a 48 MHz quad phase-locked-loop clock generator designed for digital television equipment and packaged in a 16-pin TSSOP. It operates from a 3.135 V to 3.465 V supply and provides four PLL-related clock outputs, making it suitable for systems requiring multiple related signals from a compact clock-generation circuit. A phase-locked-loop clock generator is a timing IC that synchronizes an output frequency to a reference signal. The PLL architecture supports frequency generation or multiplication while distributing multiple clock phases or related outputs. Within the broader semiconductor hierarchy, this device is a clock and timing IC, a programmable logic device based on phase-locked-loop technology, and a system-level clock-generation component. The ICS487G-25 is identified as a quad PLL for DTV, with a nominal operating frequency of 48 MHz. Its 3.135 V to 3.465 V supply range centers around a nominal 3.3 V rail, while the 16-TSSOP package provides a surface-mount footprint suitable for compact digital television and video-processing equipment. The device is supplied in a tube according to the manufacturer product listing. The quad-output architecture can reduce the number of separate oscillator or buffer components needed when several related clocks are required. Because PLL outputs share a common frequency reference, they can provide repeatable phase relationships when configured correctly. Exact output frequencies, feedback ratios, jitter, operating temperature, and control-pin functions must be confirmed in the manufacturer datasheet before final circuit design. Typical uses include digital television receiver and display electronics, video timing systems, set-top equipment, and other consumer or professional AV platforms operating from a 3.3 V rail. The device is particularly relevant where four related clock signals are needed close to a video processor, scaler, demodulator, or digital interface. PCB implementation requires a low-inductance path between the device and its decoupling capacitor. Place the 3.3 V supply bypass capacitor close to the supply pin, keep clock routes short and controlled, and route other high-speed signals away from PLL inputs and outputs. Use the pin-description table in the manufacturer datasheet when assigning tracks and confirming the exposed or no-connect positions. This page combines the 48 MHz operating point, 3.3 V supply range, 16-TSSOP packaging information, replacement analysis, and practical layout guidance in one engineering-focused reference. It is intended to accelerate initial circuit selection while directing design-critical details to the authoritative Renesas datasheet and layout guidance.

RFQ تماس
ICS501AM - 200MHz PLL Clock Generator | Renesas Electronics
ICS501AM

ICS501AM - 200MHz PLL Clock Generator | Renesas Electronics

The Renesas Electronics ICS501AM is a single PLL-based clock generator that produces a CMOS clock output at up to 200 MHz from a lower-frequency crystal or clock input. It uses a 1:1 input-to-output ratio, accepts either clock or crystal input, and is housed in an 8-pin SOIC package measuring 3.90 mm wide. The ICS501A LOCO series provides a practical clock multiplication solution when a system requires a higher-frequency operating clock without requiring a full custom oscillator or complex external frequency-generation network. A PLL clock generator is a timing IC that phase-locks its output to a reference source and multiplies the reference frequency to produce a stable, high-frequency clock. Within the broader semiconductor hierarchy, the ICS501AM belongs to the clock and timing IC family, specifically the clock-generator and PLL subcategory. Its role in electronic systems is to distribute a high-speed clock for digital logic, processors, communication equipment, and other clocked circuits while maintaining a defined relationship to the input reference. The primary features of the ICS501AM are its maximum output frequency of 200 MHz, single-clock-generator configuration, 1:1 input-to-output ratio, PLL architecture, and CMOS output. The ability to operate from either a crystal or external clock gives the device flexibility in clock-tree design. Its 8-SOIC surface-mount package also allows relatively compact PCB placement compared with larger through-hole oscillator arrangements. These characteristics make the part useful where frequency generation, standard logic voltage compatibility, and manageable board area are important. Technically, the ICS501AM uses a phase-locked loop to generate a higher-quality clock output from a lower-frequency reference. The PLL-based approach provides a controlled relationship between the input reference and generated output, while the CMOS output supports integration with conventional digital timing circuits. The 1:1 ratio identifies the device as a clock-generation solution rather than a programmable integer or fractional-N frequency synthesizer. Exact input frequency limits, operating-voltage range, output jitter, and load-drive capability should be confirmed in the manufacturer datasheet before final circuit release. Typical applications include digital control systems, embedded processing platforms, communication modules, industrial control equipment, and general-purpose clock-distribution designs. In each case, the part can serve as the central clock source when a higher-frequency CMOS clock is required and a crystal or lower-frequency reference is already present. The absence of differential inputs or outputs also simplifies point-to-point clock routing, although signal-integrity and return-path design remain important at high clock rates. When laying out a design using the ICS501AM, keep the crystal, reference clock, feedback network, and decoupling paths consistent with the manufacturer reference configuration. Confirm all capacitance, drive-strength, and grounding requirements before fabrication because incorrect peripheral-component values or long loop lengths can affect PLL stability and clock quality. Validate startup, jitter, and output amplitude across temperature and supply-voltage corners rather than relying only on nominal simulation results. This product page combines the ICS501AM clock-generator specifications, verified package information, compatible same-family ordering options, and practical integration guidance. It provides engineers with a concise basis for initial design selection while directing detailed timing, electrical-limit, and qualification decisions to the Renesas manufacturer documentation.

RFQ تماس
ICS501AMI - 166MHz Clock Generator IC | Renesas | SOIC-8
ICS501AMI

ICS501AMI - 166MHz Clock Generator IC | Renesas | SOIC-8

The Renesas Electronics ICS501AMI is a 166MHz clock generator IC packaged in an 8-pin SOIC, using a CMOS clock interface to produce a high-quality output from a lower-frequency crystal or clock input. As an ICS501A LOCO clock multiplier, it provides a compact alternative to a full crystal oscillator when the system already has a reference source that can be multiplied. The 0.154-inch-wide SOIC-8 package measures 3.90mm in body width and supports surface-mount assembly. A clock generator is a timing IC that converts or multiplies a lower-frequency reference into a higher-frequency clock for digital logic, processors, communications equipment, and embedded control systems. Within the clock and timing hierarchy, the ICS501AMI belongs to the clock-generator and PLL-clock-multiplier class, combining a frequency reference with a phase-locked loop. It differs from a conventional oscillator because it does not require a complete resonator-and-amplifier arrangement when an external reference is available. The ICS501A architecture supports generation of a high-quality, high-frequency clock output from a lower-frequency crystal or clock input. Its stated maximum operating frequency is 166MHz, while CMOS-compatible clock signaling integrates with modern digital systems. Operating from a single low-voltage supply keeps the implementation compact, although the exact supply-voltage limits, current consumption, output jitter, lock-range limits, and temperature ratings should be confirmed against the manufacturer datasheet before release to production. A typical implementation places the low-frequency reference at the timing input, connects the required support components, and routes the multiplied clock to the destination logic. The crystal or reference circuit must satisfy the frequency and load requirements stated in the manufacturer datasheet. PCB layout, grounding, and supply bypassing become increasingly important as the output frequency rises because clock-edge jitter and power-supply noise can reduce system timing margin even when the nominal output frequency is correct. ICS501AMI is appropriate for digital control systems, embedded processing, industrial electronics, communications equipment, and retrofit designs that use the established ICS501 footprint. It can also serve clock-tree distribution when an existing reference signal should be reused. For battery-powered equipment, compare the device's operating current and idle behavior against system power budgets. In systems requiring precise synchronization among multiple domains, first confirm the device's PLL lock behavior and output stability under the intended reference conditions. Use the manufacturer's pin-description table when assigning PCB tracks, and preserve the documented bypass-capacitor layout to minimize supply noise at the clock pins. Verify startup, reference stability, output waveform, and maximum operating frequency across the full intended temperature range. This page combines the available manufacturer and distributor information with practical implementation guidance, sourcing questions, and clearly qualified same-package alternatives for design review.

RFQ تماس
ICS501AMT - 200MHz PLL Clock Generator | Renesas Electronics
ICS501AMT

ICS501AMT - 200MHz PLL Clock Generator | Renesas Electronics

Renesas Electronics ICS501AMT is a single PLL-based clock generator that produces a CMOS clock output up to 200 MHz from a lower-frequency crystal or clock input. It operates from a 3 V to 3.6 V supply in an 8-SOIC surface-mount package and is supplied in tape-and-reel packaging. The device provides a 1:1 input-to-output ratio, supports either crystal or external-clock excitation, and uses a non-differential clock architecture. A PLL clock generator is an integrated clock and timing circuit that locks an internal oscillator to an external reference before multiplying or conditioning that reference into a higher-frequency output. In the broader semiconductor hierarchy, the ICS501AMT belongs to the clock-generator family, within clock and timing ICs and the broader power-management and semiconductor ecosystem. Its purpose is to provide a stable, high-frequency timing reference without requiring a complete external crystal-oscillator assembly for every application. The primary features of the ICS501AMT include a maximum output frequency of 200 MHz, one clock circuit, a 1:1 input-to-output ratio, CMOS output compatibility, and support for either a crystal or an external clock. These characteristics suit designs that need a higher-frequency clock derived from a lower-frequency source. The 3 V to 3.6 V operating range also places the device in a supply class commonly used by compact digital, communications, and embedded systems. Technically, the ICS501AMT uses phase-locked-loop clock multiplication to establish a high-quality clock output from its reference input. The architecture is intended to replace conventional discrete crystal-oscillator arrangements in suitable electronic systems. Because the device accepts either a crystal or clock input, the design can support different reference-generation methods, although the crystal frequency, loop stability, jitter, output-waveform requirements, and load conditions must be evaluated before committing to a specific implementation. Typical applications include digital logic clocking, communications-module timing, embedded processing, interface timing, instrumentation, and general-purpose frequency multiplication. In each case, the device acts as the clock source for circuitry requiring a CMOS-compatible reference. Its surface-mount SOIC package supports automated assembly, while the tape-and-reel configuration is intended for high-volume production and pick-and-place manufacturing. The principal design consideration is preserving a clean reference and a controlled board environment. Route the crystal or clock input with short, symmetric traces, maintain the recommended support network, and keep sensitive timing paths away from noisy switching circuitry. Confirm output loading, rise-time limits, and downstream clock requirements against the manufacturer datasheet before layout release. The 200 MHz maximum rating is a device limit, not a guarantee that every crystal or board implementation will produce acceptable jitter at that frequency. This product page consolidates the device architecture, operating limits, package information, sourcing guidance, and engineering trade-offs needed to evaluate the ICS501AMT. It also distinguishes verified drop-in replacements from generic clock-generator alternatives, helping designers assess PCB compatibility, supply voltage, output frequency, and timing requirements before selecting a replacement.

RFQ تماس
ICS501G - 160MHz PLL Clock Generator | Renesas | Timing
ICS501G

ICS501G - 160MHz PLL Clock Generator | Renesas | Timing

The Renesas Electronics ICS501G is a single-circuit PLL clock generator with a maximum frequency of 160MHz, CMOS output, and support for crystal or external clock inputs. It is available in 8-TSSOP and 8-MSOP packages, making it suitable for compact digital systems that require frequency multiplication or clock generation. The verified distributor listing identifies the device as an 8-pin surface-mount clock-generator IC. A PLL-based clock generator multiplies or conditions a lower-frequency reference to produce a stable, high-frequency clock for digital logic, processors, communications equipment, and embedded systems. The ICS501G belongs to the broader clock and timing hierarchy: oscillator and crystal support → clock generator → PLL clock multiplier → digital timing subsystem. Its CMOS output and 160MHz maximum frequency suit moderate-speed digital clocking requirements, although timing margins must be checked for the selected operating condition. Key verified attributes include PLL operation, one clock-generator circuit, a 1:1 input-to-output ratio in the cited specification summary, and no differential input or output. The available package information is 8-TSSOP or 8-MSOP, depending on the orderable package variant represented by the ICS501G family listing. The exact electrical limits, crystal-load details, output-drive capability, jitter, and recommended decoupling requirements were not supplied in the verified excerpts and must be confirmed in the manufacturer datasheet before layout release. Typical uses include microcontroller and processor clock generation, digital interface timing, embedded control systems, and communications modules requiring a local high-frequency reference. The device is intended to replace conventional crystal-oscillator arrangements in suitable electronic systems, according to the Renesas product description. Designers should account for supply voltage, output load, trace impedance, grounding, and the timing relationship between the generated clock and downstream circuitry. A key design consideration is to validate the reference clock and PLL configuration against the exact datasheet before production. Keep the oscillator and feedback paths short, provide a clean return path, and place required decoupling capacitors close to the supply pins. Because the verified data does not state the full pinout, pin names, or package-specific ordering details, those values remain subject to datasheet verification. This page consolidates verified distributor specifications, official Renesas datasheet information, application guidance, and drop-in replacement constraints into an engineering-focused component record for sourcing and design review.

RFQ تماس
ICS501GI - 140MHz PLL Clock Generator | Renesas Electronics
ICS501GI

ICS501GI - 140MHz PLL Clock Generator | Renesas Electronics

Renesas Electronics ICS501GI is a PLL clock-generator integrated circuit that produces a high-quality clock output from a lower-frequency crystal or external clock input. The device supports operation up to 140 MHz, uses a CMOS output, and is packaged as an 8-TSSOP or 8-MSOP with a stated width of 0.118 inches, or 3.00 mm. It is intended for systems that require a stable, high-frequency clock without implementing a complete clock-generation subsystem on the host board. A PLL clock generator is a timing IC that multiplies or otherwise conditions a reference clock to produce one or more higher-frequency outputs. Clock generators belong to the broader clock and timing IC hierarchy, where they work alongside oscillators, dividers, buffers, phase-locked loops, and frequency synthesizers. Their primary function is to convert a convenient low-frequency crystal reference into the clock domain required by processors, communication circuits, converters, and digital peripherals. The ICS501GI uses a phase-locked loop, allowing an external clock or crystal to serve as the reference while the internal multiplier generates a higher-frequency CMOS clock. Its maximum listed operating frequency is 140 MHz. The device contains one clock-generation circuit and has a listed input-to-output ratio of 1:1 in the referenced specification summary. These characteristics make it suitable for designs requiring a compact, single-channel clock source rather than a programmable multi-output synthesizer. Renesas markets the ICS501 family under the LOCO name, describing it as a cost-effective method for generating a high-quality, high-frequency clock from a lower-frequency crystal or clock input. The CMOS output interface suits digital systems operating with CMOS-compatible logic levels. Because this ICS501GI variant is offered in a compact 8-pin TSSOP/MSOP package, it can support space-conscious boards while retaining separate connections for power, ground, reference input, and clock output. Typical uses include digital control systems, embedded processing modules, communications equipment, clock distribution for digital logic, and clock generation where a system already has a suitable reference crystal or external clock. The PLL-based approach can reduce the need for high-frequency external crystals while providing a clock output up to 140 MHz. System designers must still confirm loop stability, output jitter, startup behavior, load capacitance, and supply requirements against the manufacturer datasheet before releasing a production design. Layout should keep the reference-crystal or clock-input path short and route the high-speed CMOS output away from sensitive analog and communication nodes. Follow the manufacturer’s recommended input, output, and bypass-capacitor connections, and account for the required ground-return path under the exposed or connected ground pins. If frequency accuracy, jitter, or reference sensitivity is critical, evaluate the complete clock tree rather than relying only on the 140 MHz maximum-frequency headline figure. This page combines the Renesas family identification, distributor package details, PLL and frequency specifications, pin-compatible cross-reference findings, and practical selection guidance. It also distinguishes verified drop-in candidates from generic cross-reference tools, helping engineers focus on same-package replacements that still require datasheet-level timing and application validation.

RFQ تماس
ICS501GIT - 140MHz CMOS Clock Generator | Renesas Electronics
ICS501GIT

ICS501GIT - 140MHz CMOS Clock Generator | Renesas Electronics

The Renesas Electronics ICS501GIT is a single-output CMOS clock generator with a maximum frequency of 140 MHz, a phase-locked loop, and crystal or clock input support, supplied in an 8-pin TSSOP package. It provides a 1:1 input-to-output ratio and is designed to generate a high-quality clock from a lower-frequency reference. The ICS501GIT is commonly associated with the LOCO family of clock generators, combining frequency multiplication, clock generation, and oscillator functions in one timing IC. A clock generator is a clock-and-timing semiconductor that converts a crystal or external clock reference into a stable digital waveform for sequential digital logic. Within the timing hierarchy, the ICS501GIT is a PLL-based clock generator, which is a type of frequency generator and clock-and-timing IC. Its role is to provide a repeatable clock source to processors, communications equipment, test systems, and other digital circuits that require coordinated timing. The principal verified specifications for the ICS501GIT include a 140 MHz maximum frequency, one clock output, CMOS output technology, PLL support, and crystal or clock input. It accepts either a crystal reference or an external clock, while its nominal 1:1 input-to-output ratio simplifies designs that require frequency multiplication rather than programmable division. The 8-pin TSSOP, also identified as 8-MSOP with a 3.00 mm body width, supports compact surface-mount layouts. Its PLL architecture provides a practical alternative to relying only on a high-frequency crystal or an external oscillator module. The clock generator converts a lower-frequency reference into a higher-frequency CMOS output, reducing the component count compared with discrete oscillator and buffer arrangements. Because the public listing does not expose detailed operating, voltage, temperature, or jitter tables, those characteristics should be confirmed in the manufacturer datasheet before release to production. Typical uses include digital controller timing, embedded communications equipment, data-acquisition systems, general-purpose clock distribution, and replacement of higher-cost discrete crystal-oscillator arrangements. The device is particularly appropriate when a design needs a standard CMOS clock output, a PLL-based frequency-generation stage, and a compact 8-pin surface-mount footprint. Input and output edges remain important considerations in high-speed systems. Place the crystal, input clock, decoupling capacitor, and output routing according to the manufacturer reference layout. Keep the oscillator loop short, maintain a clean return path, and route the 140 MHz-capable clock away from high-current switching nodes. Confirm input amplitude, supply voltage, output load, and maximum operating frequency against the exact datasheet revision before production. This product page consolidates the verified ICS501GIT specifications, manufacturer documentation link, lifecycle-relevant sourcing information, compatible family references, and practical PCB guidance. The alternatives are restricted to documented TSSOP-8 clock-generator references, while the selection tables make package, brand, and compatibility differences explicit for design review.

RFQ تماس
ICS501GT - 160MHz PLL Clock Generator | Renesas Electronics
ICS501GT

ICS501GT - 160MHz PLL Clock Generator | Renesas Electronics

Renesas Electronics ICS501GT is a single-circuit PLL clock generator IC with a maximum operating frequency of 160 MHz, accepting either a crystal or clock input and providing a CMOS clock output. The device is offered in an 8-TSSOP, also identified as an 8-MSOP measuring 0.118 inch by 3.00 mm wide. Its 1:1 input-to-output ratio and integrated PLL make it suitable for replacing multiple discrete crystal-oscillator functions with one clock-generation component. A clock generator IC is a timing semiconductor that converts a lower-frequency crystal or external clock into a stable, high-frequency clock required by digital systems. Clock generators occupy the Clock & Timing category and may include oscillator, PLL, frequency multiplier, divider, and buffer functions. The ICS501GT uses phase-locked-loop technology to multiply a reference frequency while providing a CMOS output suitable for digital logic and communications equipment. Principal features include a maximum frequency of 160 MHz, one internal clock-generating circuit, support for crystal or clock inputs, and CMOS output. The 1:1 ratio indicates that the nominal output follows the selected reference relationship without an integer multiplication factor other than the internally programmed PLL ratio. The single-circuit architecture simplifies designs that require only one principal clock domain and reduces the number of separate oscillator packages and interconnections. The ICS501GT is identified as a LOCO-family device, with LOCO standing for Low Cost Oscillator. Its PLL-based approach is intended to produce a high-quality, high-frequency clock from a lower-frequency crystal or clock source. The resulting CMOS output can serve digital processors, programmable logic, interface controllers, and other clocked subsystems, provided that the reference frequency, operating voltage, output loading, and timing requirements are checked against the device specifications. Typical applications include communications and networking modules, industrial control equipment, consumer electronics, embedded digital systems, and FPGA or microcontroller clock trees. In these systems, the part can centralize clock generation, reduce crystal-oscillator component count, and provide a consistent clock source to multiple sequential logic domains. The exact frequency plan must remain within the 160 MHz maximum and comply with the PLL multiplication and timing limits defined by the manufacturer datasheet. The primary design consideration is confirming the complete pin configuration and reference requirements before layout. Crystal load capacitance, grounding, output termination, supply decoupling, and unused-pin treatment all affect clock quality and reliability. Follow the manufacturer pin-description table and recommended application circuit when assigning PCB tracks, and preserve short return paths from the clock output to the load to limit susceptibility to edge degradation and crosstalk. This product page organizes the ICS501GT clock-generator specifications, package information, documented substitution candidates, application guidance, and practical design notes into one engineering-focused reference. It supports faster part identification while highlighting the decisions engineers must still verify: frequency ratio, electrical limits, pin compatibility, lifecycle suitability, and application-specific timing requirements.

RFQ تماس
ICS501M - 160 MHz PLL Clock Generator | Renesas | SOIC-8
ICS501M

ICS501M - 160 MHz PLL Clock Generator | Renesas | SOIC-8

The Renesas Electronics ICS501M is a LOCO PLL clock-multiplier and clock-generator IC with a 2 MHz to 50 MHz input range and up to 160 MHz output, housed in an 8-pin SOIC package. It generates high-frequency clock signals from a lower-frequency crystal or clock input, making it useful where a board requires local frequency multiplication without relying on a full crystal oscillator. The verified product listing identifies the ICS501M as a clock-generator IC with a 160 MHz maximum output and an 8-SOIC package. A clock generator is an integrated timing device that accepts a reference clock and produces one or more clock outputs with controlled frequency and phase relationships. A PLL clock multiplier belongs to the clock and timing IC hierarchy, alongside oscillators, frequency synthesizers, phase-locked loops, and clock buffers. The ICS501M uses phase-locked-loop techniques to multiply a lower-frequency source into a higher-frequency output, reducing the need for a high-speed crystal when the downstream circuit can tolerate the device’s timing characteristics. The verified ICS501M data specifies a 2 MHz to 50 MHz input range and a maximum 160 MHz output. Its 8-pin SOIC package is a surface-mount gull-wing package, and distributor records classify the device as a clock-generator or PLL clock-multiplier IC. The available material also identifies the LOCO product family as a cost-effective way to produce high-quality high-frequency clock outputs from lower-frequency crystals or clock inputs. Detailed operating-temperature, voltage, jitter, output-waveform, and load-current values are not present in the supplied verified data. Typical design use includes communications and networking equipment, digital logic requiring a multiplied reference clock, embedded systems, instrumentation, and embedded processing platforms. The device can be placed after a stable low-frequency crystal or digital clock source when the receiving circuitry needs a higher clock frequency. Designers should verify output frequency tolerance, phase noise, supply requirements, and timing margins against the downstream load before releasing a production design. The key design consideration is that frequency multiplication is not a substitute for verifying the complete clock chain. The reference source, crystal or source impedance, PLL loop behavior, output loading, and downstream timing requirements must be checked together. Because the supplied data does not include the full electrical timing table, those parameters remain marked as data needed rather than inferred. This page combines verified distributor and manufacturer-document references, package information, application context, pricing status, and replacement-screening guidance. It is intended to support preliminary BOM research while directing engineers to the exact manufacturer datasheet for final electrical, timing, reliability, and qualification decisions.

RFQ تماس
ICS501MI - 140MHz LOCO PLL Clock Multiplier | Renesas Electronics
ICS501MI

ICS501MI - 140MHz LOCO PLL Clock Multiplier | Renesas Electronics

The Renesas Electronics ICS501MI is a LOCO PLL clock multiplier that generates a high-quality, high-frequency clock output from a lower-frequency crystal or clock input. It supports input frequencies from 2 MHz to 50 MHz and provides an output clock up to 140 MHz in an 8-pin SOIC package. The device is designed to replace conventional crystal oscillators in electronic systems where a stable reference clock multiplied to a higher frequency is required. A PLL-based clock generator is a timing IC that phase-locks an output signal to a reference source and multiplies the reference frequency. In the broader clock and timing hierarchy, the ICS501MI belongs to the PLL clock-multiplier family, a type of clock and timing IC used for frequency synthesis, clock distribution, and digital system timing. Its LOCO designation reflects a low-cost oscillator architecture intended to provide economical frequency multiplication without requiring a separate high-frequency crystal resonator. The ICS501MI accepts a fundamental-mode crystal or external clock source, making it useful for processor, communication, control, and embedded digital systems. The 140 MHz maximum output frequency provides ample headroom for systems requiring a higher-frequency operating clock from a lower-cost reference. Its 8-SOIC package is compatible with conventional surface-mount PCB assembly methods and is suitable for designs where component count and board area must be controlled. The principal design consideration is ensuring that the reference crystal, external clock, feedback network, and output interface meet the timing requirements of the target system. The PLL must operate within the specified input and output frequency ranges, and the associated passive components should be placed close to the device to minimize clock noise and signal-integrity degradation. The output clock should be routed away from high-current switching nodes and noisy analog sections of the board. Typical applications include digital controller clocking, communications equipment, embedded processors, industrial control systems, and general-purpose frequency multiplication. Using a PLL multiplier can reduce the number of specialized high-frequency crystals required in a design and provide a flexible way to derive multiple system timing domains. XAIPART provides an engineering-focused product record with manufacturer documentation, package information, practical design guidance, and verified sourcing details for design review and procurement.

RFQ تماس
ICS501MIT - 140MHz PLL Clock Generator | Renesas Electronics
ICS501MIT

ICS501MIT - 140MHz PLL Clock Generator | Renesas Electronics

Renesas Electronics ICS501MIT is a single-channel CMOS clock generator with a phase-locked loop, a maximum output frequency of 140 MHz, and an 8-pin SOIC package measuring 3.90 mm in width. It accepts either a crystal or external clock input and provides a 1:1 input-to-output ratio, making it suitable for generating a stable high-frequency clock from a lower-frequency reference. A clock generator is a timing IC that converts a stable reference into a usable clock signal for digital circuitry. Clock generators occupy the clock and timing branch of semiconductor devices and can incorporate a phase-locked loop, frequency multiplication, programmable dividers, and output drivers. The ICS501 family is based on the LOCO concept, intended to replace a discrete crystal oscillator in many electronic systems while retaining a compact integrated implementation. The ICS501MIT combines a maximum frequency of 140 MHz with CMOS output, PLL capability, and a 3.00 V to 5.25 V operating supply range. Its input may be a crystal or clock signal, and its nominal input-to-output ratio is 1:1. These characteristics suit digital systems that require a local timing reference without accepting the component count and assembly complexity of a discrete oscillator arrangement. At its core, the integrated PLL locks the generated output to the selected reference. Clock feedback and phase comparison allow the output frequency to remain associated with the reference while the device provides a clean CMOS clock to digital logic. Because the available data identifies a single clock generator circuit rather than multiple independently programmable outputs, the device is best treated as a focused timing solution rather than a multi-channel clock-tree component. Typical applications include communications equipment, industrial control systems, test and measurement instruments, embedded digital platforms, and general-purpose logic designs. It is particularly appropriate when the design needs a 140 MHz-capable CMOS clock, an integrated PLL, and an 8-pin surface-mount footprint. The package also permits economical PCB assembly using standard SOIC-8 manufacturing practices. Designers should select the crystal or reference frequency so that the resulting clock remains within the 140 MHz maximum and verify the input, output, and supply timing requirements against the manufacturer datasheet. Decoupling should be placed close to the supply pin, while clock routing should preserve a short return path and minimize coupling into sensitive analog or high-speed digital nets. This product page combines the ICS501MIT operating envelope, pin-compatible replacement findings, package information, and practical implementation guidance to support initial design review, sourcing, and board-level validation.

RFQ تماس