محصولات (46,000+)

INA149N - ±275V High Common-Mode Difference Amplifier | TI
INA149N

INA149N - ±275V High Common-Mode Difference Amplifier | TI

The Texas Instruments INA149N is a precision unity-gain difference amplifier with a very high input common-mode voltage range of up to ±275 V, housed in an 8-pin SOIC package and specified over the extended industrial temperature range of -40C to +125C. A difference amplifier is a type of analog signal-conditioning amplifier that measures only the voltage difference between two input nodes while rejecting any voltage common to both. Within the signal-chain hierarchy, it sits between a raw sensor or power-rail node and an ADC, providing level shifting and common-mode rejection. The difference amplifier category belongs to the broader family of instrumentation amplifiers and amplifier ICs in precision analog front ends. The INA149 is a single, monolithic device consisting of a precision op amp and an integrated, laser-trimmed thin-film resistor network. This integration is the key differentiator: the resistor matching on-chip yields a CMRR and gain accuracy that discrete resistor-op-amp solutions cannot economically match. According to the TI datasheet, the part accurately measures small differential voltages in the presence of common-mode signals up to ±275 V, and its inputs are protected from momentary voltage surges, which matters when probing motor drives, inverters, and industrial power buses. Architecturally, the thin-film network divides the high common-mode input down into the operating range of the internal precision op amp, allowing safe measurement of shunt voltages and bus voltages that sit hundreds of volts above or below the amplifier supply rails. The unity-gain configuration means the output directly reproduces the differential input, simplifying scaling math in firmware. Typical applications include high-side and low-side current sensing in motor drives, DC bus voltage monitoring in industrial inverters, battery-management systems, and data-acquisition front ends where measurement nodes must swing far beyond the ADC range. Design-wise, ensure the reference pin is driven from a low-impedance source, since reference-pin impedance directly degrades CMRR. Layout symmetry of the resistor network inputs preserves accuracy at high common-mode. This page synthesizes verified distributor data, drop-in alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet alone.

RFQ تماس
INA152EA/250 - 800 kHz Single-Supply Difference Amplifier | TI
INA152EA/250

INA152EA/250 - 800 kHz Single-Supply Difference Amplifier | TI

The Texas Instruments INA152EA/250 is a single-supply, unity-gain difference amplifier with 800 kHz bandwidth, 1.5 mV input offset voltage, and 1 dB gain error, packaged in an 8-pin VSSOP (DGK). The device integrates a CMOS operational amplifier with a precision, laser-trimmed resistor network to measure small differential signals accurately in low-power instrumentation systems. A difference amplifier is a specialized operational-amplifier configuration that rejects a voltage common to both inputs while amplifying their difference. The INA152 belongs to the precision analog signal-chain hierarchy: instrumentation amplifier, difference amplifier, operational amplifier, analog IC. Its integrated resistor network removes the need for an external matched resistor divider, simplifying current sensing, bridge excitation, and low-level front-end designs while preserving stable ratio behavior over temperature. Important characteristics include a unity nominal gain, 0.01% gain accuracy from laser trimming, 800 kHz bandwidth, 1.5 mV input offset voltage, and 1 dB gain error. The INA152EA/250 operates across a -40 °C to +85 °C temperature range and is specified for an 8-VSSOP surface-mount package. Its integrated resistor network is designed for accurate common-mode rejection and gain stability across temperature. The device uses a single-supply architecture, which simplifies analog signal acquisition where a negative supply is unavailable or undesirable. A single supply supports battery-powered, portable, industrial-sensor, and low-power test equipment designs. Because input and output headroom are constrained near the supply rails, the usable input and output common-mode ranges should be confirmed against the manufacturer datasheet for the exact operating voltage. Typical uses include high-side or low-side current measurement, resistive sensor bridges, differential sensor interfaces, industrial process-control front ends, and low-power diagnostic instruments. The 800 kHz bandwidth is suitable for slow-to-moderate dynamic measurements rather than high-speed waveform capture. The integrated, trimmed network is particularly useful when maintaining accurate differential gain without calibrating several discrete resistors. For board design, place the device close to the source node and route the differential inputs as a short, tightly coupled pair to minimize pickup of external noise. Connect the ground return directly to the source reference and use the pin-description table in the manufacturer datasheet when assigning PCB tracks. Verify supply decoupling, common-mode limits, output drive, and settling behavior in the application that sets the smallest signal of interest. This page combines manufacturer specifications, package and ordering details, drop-in family alternatives, comparison parameters, and practical design guidance to support component selection, PCB planning, and precision analog front-end design.

RFQ تماس
INA154U - 3MHz High-Speed Difference Amplifier | Texas Instruments
INA154U

INA154U - 3MHz High-Speed Difference Amplifier | Texas Instruments

The Texas Instruments INA154U is a high-speed, precision difference amplifier with a fixed gain of 1, 3 MHz bandwidth, and an 8-pin SOIC package. It is designed for low-cost applications requiring accurate subtraction of two input voltages. Verified manufacturer data identifies the device as a single-circuit differential amplifier specified for operation from -40°C to +85°C. A difference amplifier is a specialized operational-amplifier circuit that subtracts one input voltage from another while rejecting common-mode voltage. In signal-chain terms, the INA154U belongs to the instrumentation-amplifier and differential-input amplifier hierarchy: differential amplifier -> precision analog amplifier -> analog signal-conditioning IC -> semiconductor. Its integrated precision resistor network provides the fixed difference function without requiring four external matched resistors. Verified features include a maximum input offset voltage of ±750 µV, maximum offset drift of ±2 µV/°C, maximum gain error of ±0.05%, and wide bandwidth of 3 MHz. These parameters make the device suitable where differential signal extraction, bridge measurement, current measurement, or sensing of small voltage differences is required. The manufacturer describes the amplifier as high-speed and precision, while the verified search results identify an 8-SOIC package and one amplifier circuit per device. The INA154U is intended for low-cost designs rather than being described as an ultra-low-noise or high-voltage instrumentation amplifier. Its performance should be evaluated against the actual signal amplitude, source impedance, common-mode range, supply voltage, bandwidth, and required accuracy. The reference pin and input common-mode limits are important when selecting external protection, filtering, and bias circuitry. The verified manufacturer datasheet is the authoritative source for electrical limits and pin functions. Typical uses include differential sensor interfaces, balanced audio and communications signal paths, bridge amplifiers, ADC input conditioning, and precision current-shunt measurements. In a typical application, the two inputs are connected to the sensed differential pair and the output presents the scaled difference. Input and output filtering can be added to control bandwidth, suppress switching noise, and protect the amplifier from transients. When laying out the circuit, keep the differential input traces short and matched, connect the reference pin to a low-impedance bias reference when required, and place input filtering close to the amplifier pins. The integrated resistor network's tolerance and temperature drift should be included in the system error budget. This page combines verified manufacturer specifications, source traceability, application guidance, and replacement constraints for practical design review.

RFQ تماس
INA154UA - 3.1MHz Precision Difference Amplifier | Texas Instruments
INA154UA

INA154UA - 3.1MHz Precision Difference Amplifier | Texas Instruments

Texas Instruments INA154UA is a high-speed, precision difference amplifier with a fixed gain of 1 V/V, 3.1 MHz bandwidth, and 14 V/µs slew rate. The device is supplied in an 8-pin SOIC package and is specified for operation from -40°C to +85°C. It is designed for measuring small differential signals in the presence of larger common-mode voltages. A difference amplifier is an amplifier type that subtracts two input voltages and amplifies the resulting differential signal. The INA154 integrates a precision operational amplifier with a laser-trimmed resistor network, implementing the differential function without requiring an external precision resistor network. It belongs to the broader instrumentation-amplifier and differential-amplifier category within analog signal-chain integrated circuits. Key features include a fixed gain of 1 V/V, maximum input offset voltage of ±750 µV, maximum offset drift of ±2 µV/°C, maximum gain error of ±0.05%, and wide bandwidth of approximately 3 MHz. The device is intended for low-cost, precision differential signal conditioning where the input signal is small relative to the common-mode voltage. The INA154 combines an internal precision amplifier with an integrated, laser-trimmed resistor network. Its high-speed architecture supports signals extending to megahertz frequencies, while the fixed unity gain simplifies system design. Common-mode rejection is valuable in sensor interfaces, industrial measurement systems, and instrumentation applications where unwanted common-mode noise could otherwise obscure the desired differential signal. Typical applications include current sensing, sensor signal conditioning, bridge amplifier inputs, industrial process measurement, and differential communication interfaces. The 8-pin SOIC package makes the device suitable for compact analog boards, provided the designer follows the manufacturer’s recommended input network, supply bypassing, and grounding guidance. The primary design consideration is common-mode voltage and input range. The amplifier’s differential output responds to the difference between the two inputs, but the applied voltages must remain within the device’s permitted operating and common-mode limits. Decoupling capacitors should be placed close to the supply pins, and sensitive analog routing should minimize differential pickup between the input traces. This page consolidates the verified manufacturer and distributor information, distinguishes the fixed-gain INA154UA from general-purpose op-amp alternatives, and highlights package, temperature, offset, bandwidth, and sourcing details useful during component selection.

RFQ تماس
INA155U - 5.5V 550kHz CMOS INA | Texas Instruments
INA155U

INA155U - 5.5V 550kHz CMOS INA | Texas Instruments

The Texas Instruments INA155U is a single-supply, rail-to-rail-output CMOS instrumentation amplifier with a 5.5 V maximum supply, 550 kHz bandwidth, and 1 mV offset specification, housed in an 8-pin SOIC package. It is designed for low-voltage sensor and measurement circuits where a differential input must be amplified accurately while operating from one supply. The rail-to-rail output architecture supports signal chains that operate close to the positive supply rail, while the CMOS implementation targets low-power analog signal conditioning. An instrumentation amplifier is a specialized analog IC that amplifies the difference between two input signals while rejecting common-mode noise. INA155U belongs to the broader hierarchy of analog signal-conditioning devices: instrumentation amplifier, differential amplifier, analog amplifier, and semiconductor. This device is particularly useful when a sensor output is small, noisy, or referenced to a changing common-mode voltage and the next stage requires a larger single-ended signal. The manufacturer identifies the INA155 family as a 5.5 V single-supply, 550 kHz, rail-to-rail-output CMOS instrumentation amplifier. The verified distributor data identifies INA155U as a one-circuit, rail-to-rail-output device in an 8-pin SOIC package. The 550 kHz bandwidth makes it appropriate for signal paths that require response beyond static precision measurements, provided the application does not require high-frequency instrumentation-amplifier performance. The INA155U is intended for low-voltage sensor interfaces, portable measurement systems, industrial signal conditioning, and analog-to-digital converter front ends. Its rail-to-rail output can simplify designs using a 3.3 V or 5 V supply because the output can swing close to the upper rail under suitable load conditions. The exact input common-mode range, gain settings, output swing, noise, and current specifications were not included in the verified data and must be checked in the manufacturer datasheet before final design release. For PCB implementation, use a low-noise ground reference, place input and feedback components close to the device, and keep sensitive differential traces short and symmetric. Decoupling capacitors should be placed at the supply pins according to the manufacturer recommendations. Verify the complete signal chain against the datasheet limits, especially when the source impedance, gain, output load, supply voltage, or common-mode input level differs from the nominal application conditions. This page combines the verified INA155U product identity and distributor links with structured application, comparison, and design guidance. It does not infer electrical values that were not explicitly supplied in the retrieved data, and it identifies missing parameters for engineering confirmation.

RFQ تماس
INA155UA - 550 kHz Single-Supply CMOS Instrumentation Amp | TI
INA155UA

INA155UA - 550 kHz Single-Supply CMOS Instrumentation Amp | TI

The Texas Instruments INA155UA is a single-supply, rail-to-rail-output CMOS instrumentation amplifier designed for low-voltage signal conditioning. It operates from a 2.5 V to 6 V supply, provides 550 kHz bandwidth, has a 1 mV input offset voltage, and is available in an 8-pin SOIC package. The device is intended for applications requiring differential input measurement, current sensing, sensor interfaces, and low-voltage analog signal conditioning. An instrumentation amplifier is a differential-input analog amplifier that combines high input impedance, accurate gain setting, and common-mode rejection into one integrated device. The INA155UA belongs to the instrumentation amplifier category, which is part of the broader amplifier IC and analog signal-processing hierarchy. Its rail-to-rail output allows the output to approach the supply rails, while its CMOS construction supports low-voltage operation and compact analog designs. The INA155UA provides adjustable gain through external resistors, with the manufacturer describing the device as a 1 mV-offset, 550 kHz rail-to-rail CMOS instrumentation amplifier. The 550 kHz bandwidth is particularly useful for signals that require more bandwidth than a precision-only instrumentation amplifier but do not require the bandwidth of a high-speed differential ADC frontend. The 6.5 V/us slew rate listed in distributor search data helps characterize its ability to respond to changing input conditions. The device is suited to low-voltage sensor conditioning, including bridge and strain-gauge signals, because its differential input architecture rejects common-mode noise when the common-mode voltage remains within the specified input range. It can also be used with current-shunt measurements, where the instrumentation amplifier converts a small differential voltage across a shunt into a larger single-ended signal. The rail-to-rail output is useful in systems where the available output headroom is limited. Typical applications include industrial process measurement, portable instrumentation, battery-powered sensor interfaces, current monitoring, and low-voltage data acquisition. When designing around the INA155UA, confirm the complete input common-mode range, output swing, gain resistor values, supply decoupling, and operating temperature limits against the manufacturer datasheet. Pay particular attention to the distinction between rail-to-rail output operation and rail-to-rail input operation, because only the output characteristic is explicitly identified in the provided verified data. This product record combines verified manufacturer and distributor information, package details, pricing references, replacement guidance, and application-oriented engineering notes. The provided search results confirm the INA155UA's 5.5 V single-supply classification, 550 kHz bandwidth, 1 mV offset specification, rail-to-rail output, CMOS construction, 2.5 V to 6 V supply range, and 8-pin SOIC package.

RFQ تماس
INA155UG4 - 550 kHz R-R CMOS INA | Texas Instruments
INA155UG4

INA155UG4 - 550 kHz R-R CMOS INA | Texas Instruments

The Texas Instruments INA155UG4 is a single-supply, rail-to-rail-output CMOS instrumentation amplifier with 200 uV input offset voltage, 6.5 V/ms slew rate, and 550 kHz bandwidth, packaged in an 8-pin SOIC. Designed for low-voltage signal acquisition, it amplifies differential sensor signals while operating from a 2.7 V to 5.5 V supply. An instrumentation amplifier is a precision analog amplifier category designed for differential measurement systems. Its internal topology provides input common-mode rejection and gain-setting functions in a compact package. The INA155 belongs to the broader CMOS analog amplifier, signal-conditioning IC, and power-management-aware semiconductor hierarchy, making it suitable for sensor interfaces, current measurement, and compact data-acquisition systems. The INA155UG4 provides rail-to-rail output swing, allowing the amplified signal to approach the supply limits. Its 550 kHz bandwidth supports moderate-frequency measurement signals, while the 6.5 V/ms slew rate helps preserve large-signal response. The low 200 uV input offset specification is important when measuring small differential voltages because offset error directly shifts the amplified result. A single 2.7 V to 5.5 V supply simplifies integration with low-voltage sensors and mixed-signal systems. The CMOS implementation is optimized for low-voltage, single-supply operation. Rail-to-rail output operation improves usable output range without requiring a bipolar supply, although input and output headroom still depends on gain, load, supply voltage, and operating conditions. The INA155 family is intended for general-purpose differential amplification and for driving sampling analog-to-digital converters when signal bandwidth and settling behavior satisfy the converter requirements. Typical uses include bridge-transducer interfaces, low-voltage current sensing, portable instrumentation, industrial measurement, medical monitoring, and general sensor conditioning. In these applications, the INA155UG4 converts a small differential input into a larger single-ended voltage suitable for an ADC, comparator, or downstream measurement circuit. Its 550 kHz bandwidth is appropriate for sensors whose useful signal content remains well below that frequency. A key design consideration is to verify the selected gain against the device’s gain bandwidth and output-swing limits. Keep the input and return paths short, use a clean low-noise supply, and connect the reference or return input to the appropriate analog-ground point. Check the external gain-setting implementation against the manufacturer’s recommended resistance and layout guidance before sampling fast or low-amplitude signals.

RFQ تماس
INA157U - 3MHz Precision Difference Amplifier | Texas Instruments
INA157U

INA157U - 3MHz Precision Difference Amplifier | Texas Instruments

The Texas Instruments INA157U is a high-speed, precision difference amplifier with a 3 MHz bandwidth, ±500 µV maximum offset voltage, ±2 µV/°C maximum offset drift, and ±0.05% maximum gain error. The device is supplied in an 8-pin SOIC surface-mount package and is specified for operation from -40°C to +85°C. A difference amplifier is a specialized amplifier IC that measures the voltage between two input terminals while rejecting signals common to both inputs. Positioned within the hierarchy of difference amplifier, instrumentation amplifier, operational amplifier, and analog signal-conditioning IC, it is used where accurate subtraction, current-sense measurement, or rejection of common-mode interference is required. The INA157U integrates a precision operational amplifier with a laser-trimmed resistor network. According to the Texas Instruments manufacturer datasheet, the internal resistors are ratio matched, although their absolute values may vary by ±20%. This ratio matching supports accurate gain and common-mode rejection. The listed low offset voltage, low thermal drift, low gain error, and 3 MHz bandwidth make the device useful where both dc accuracy and signal bandwidth matter. Typical applications include differential voltage measurement, current-shunt amplification, industrial sensor interfaces, bridge-sensor signal conditioning, and communication-circuit gain stages. A compact SOIC package supports conventional surface-mount assembly, while the extended industrial temperature range supports equipment operating across temperature extremes. The 3 MHz bandwidth also allows the amplifier to process signals beyond low-frequency precision-only applications. Designers should preserve adequate input and output voltage headroom, verify common-mode and output-swing limits against their actual signal, and route sensitive differential inputs using short, symmetric paths. Because the internal resistor network contributes noise and absolute resistance tolerance, board-level calibration should use ratio accuracy rather than assuming a nominal resistor value. This page combines the verified manufacturer specifications, distributor availability references, practical application guidance, and drop-in comparison information for engineers evaluating the INA157U.

RFQ تماس
INA157UA - 4MHz Difference Amplifier | Texas Instruments
INA157UA

INA157UA - 4MHz Difference Amplifier | Texas Instruments

Texas Instruments INA157UA is a high-speed, precision difference amplifier with 4 MHz bandwidth, one amplifier channel, and an 8-pin SOIC package. The device integrates a precision operational amplifier with a laser-trimmed resistor network, providing a fixed differential gain of 1 and rejecting common-mode signals without requiring an external matched resistor divider. A difference amplifier is a specialized instrumentation amplifier building block that measures the voltage difference between two inputs rather than amplifying either input relative to ground. In the broader semiconductor hierarchy, the INA157UA belongs to the amplifier IC family, specifically the difference-amplifier and instrumentation-signal-chain categories used for current sensing, bridge sensing, and measurement systems. Key features include a 4 MHz bandwidth, low maximum offset voltage of ±500 µV, low offset drift of ±2 µV/°C, and low maximum gain error of ±0.05%. The integrated resistor network eliminates the component-matching and resistor-ratio errors normally associated with discrete difference amplifiers. The INA157UA is available in the 8-pin SOIC surface-mount package. The internal architecture combines a precision operational amplifier with a precision, laser-trimmed resistor network. Its differential input arrangement supports accurate measurement of small voltage differences in the presence of substantially larger common-mode voltages. The 4 MHz bandwidth makes the device suitable for signal chains that require faster response than a conventional precision instrumentation amplifier while retaining integrated gain accuracy. Typical applications include low-side and high-side current sensing, bridge and strain-gauge signal conditioning, industrial process measurement, and differential sensor interfaces. In these systems, the INA157UA converts a small differential sensor voltage into a single-ended output while suppressing common-mode noise. It is particularly useful where an eight-pin surface-mount footprint and integrated resistor network simplify board design. When designing with the INA157UA, verify the input and output voltage limits, supply headroom, common-mode range, and operating-temperature grade against the manufacturer datasheet. Input and output layout should minimize parasitic capacitance and feedback-loop area, while a clean analog ground return is important for precision measurement. Bypass placement and trace routing should follow the datasheet recommendations rather than generic high-frequency layouts. This page combines verified manufacturer and distributor information, same-package substitution analysis, practical design guidance, and specification-by-specification comparison. It is intended to help engineers identify the INA157UA, evaluate genuine drop-in alternatives, and implement the device correctly in precision analog signal chains.

RFQ تماس
INA163UA - Low-Noise Instrumentation Amplifier | Texas Instruments
INA163UA

INA163UA - Low-Noise Instrumentation Amplifier | Texas Instruments

Texas Instruments INA163UA is a monolithic, low-noise, low-distortion instrumentation amplifier in a 14-pin SOIC package. The device uses current-feedback circuitry to provide wide bandwidth and strong dynamic response across its gain range. Its instrumentation-amplifier architecture supports differential input measurement while preserving low-noise and low-distortion performance for precision signal conditioning. The INA163UA is designed for low-level audio signals, including balanced low-impedance microphones, as well as industrial, instrumentation, and medical applications where signal integrity and measurement accuracy are important. An instrumentation amplifier is a specialized analog amplifier that provides differential gain, high input impedance, and accurate common-mode rejection. The INA163UA combines these functions in a single IC, simplifying signal-chain design when a sensor or balanced source must be amplified before measurement, conversion, or audio processing. Its current-feedback approach differentiates it from voltage-feedback amplifiers and is particularly useful where bandwidth and dynamic response need to remain strong over multiple gain settings. The principal benefit of the INA163UA is low-noise signal conditioning in demanding analog systems. Low noise preserves small-signal information and can improve the usable dynamic range of downstream converters, audio equipment, and laboratory instruments. Low distortion helps maintain signal integrity when the input contains high-quality content and the amplifier operates at practical signal levels. The device is also suitable for applications that require a compact solution rather than a discrete three-amplifier instrumentation-amplifier implementation. Typical uses include balanced microphone preamplification, audio signal conditioning, industrial measurement systems, medical instrumentation, and low-level sensor interfaces. The 14-pin SOIC package supports conventional surface-mount assembly and provides a practical upgrade path when a design requires low noise and low distortion in a compact analog IC. Designers should use the manufacturer datasheet for the complete electrical limits, gain configuration, pin assignments, recommended operating conditions, and application circuit. PCB layout should keep input and feedback connections short, maintain a clean ground reference, and place compensation or filtering components close to their associated pins. This page combines manufacturer information, distributor references, package details, practical design guidance, and drop-in alternative evaluation for faster component selection.

RFQ تماس
INA163UA/2K5 - 2.5x Low-Noise Instrumentation Amp | TI
INA163UA/2K5

INA163UA/2K5 - 2.5x Low-Noise Instrumentation Amp | TI

The Texas Instruments INA163UA/2K5 is a single-circuit, low-noise, low-distortion instrumentation amplifier with a fixed gain of 2.5, housed in a 14-pin SOIC package. It accepts dual supply voltages from ±4.5 V to ±18 V, with ±15 V identified as the typical dual-supply condition. Its current-feedback architecture provides wide bandwidth and dynamic response across a range of gain settings, making it suitable for precision low-level signal conditioning. An instrumentation amplifier is a specialized analog amplifier that measures the voltage difference between two inputs while rejecting common-mode interference. The INA163 belongs to the broader hierarchy of instrumentation amplifier, differential amplifier, analog amplifier, and semiconductor. Its internal current-feedback circuitry is particularly useful where the input signal is small, source impedance is low, and cable or grounding noise could obscure the measurement. The fixed 2.5-times gain of INA163UA/2K5 provides a practical compromise between signal amplification and bandwidth. It can amplify differential sensor, microphone, or balanced-line signals without requiring an external gain-setting network. Its low-noise, low-distortion design also helps preserve signal integrity when the amplified output is measured by an ADC, audio converter, or precision analog front end. Texas Instruments describes the INA163 as a monolithic instrumentation amplifier using current-feedback circuitry. This architecture supports wide bandwidth and excellent dynamic response over a wide range of gain. The device operates from dual supplies, allowing output signals centered around ground when equal positive and negative rails are used. Its SOIC-14 package is suitable for conventional surface-mount PCB assembly. Typical uses include low-level balanced microphone amplification, industrial bridge-sensor interfaces, medical instrumentation, audio signal conditioning, and precision data-acquisition front ends. The component is particularly appropriate when a differential source must be amplified while rejecting common-mode voltage present on both input lines. For implementation, follow the manufacturer pin-description table when connecting inputs, feedback-network connections, reference voltage, and supplies. Maintain suitable input common-mode range and output swing at the selected supply voltage. Decoupling capacitors should be placed close to the supply pins, while the amplifier should be positioned away from noisy switching nodes and high-current return paths. This page combines the manufacturer device description, ordering information, package details, technical constraints, and practical replacement guidance. It also identifies where an exact drop-in substitute cannot be confirmed without causing a change in gain, pin function, electrical performance, or board-level compatibility.

RFQ تماس
INA1650IPWR - 91dB CMRR Dual Audio Receiver | TI
INA1650IPWR

INA1650IPWR - 91dB CMRR Dual Audio Receiver | TI

The Texas Instruments INA1650IPWR is a dual-channel differential audio line receiver with 91 dB common-mode rejection ratio, -120 dB total harmonic distortion plus noise at 1 kHz for 22-dBu signals, and operation from 4.5 V to 36 V. It is packaged in a 14-pin TSSOP (PW) package for industrial surface-mount assemblies. A differential audio line receiver is an interface IC that extracts the wanted signal from a pair of conductors while rejecting voltage common to both inputs. It belongs to the receiver path in a broader signal-chain hierarchy of audio source, balanced line interface, converter, amplification, and loudspeaker stages. Precision matching of the integrated resistors helps preserve the audio signal when substantial unwanted voltage is present on both input lines. The INA1650 provides two receiver channels, allowing one device to handle a stereo balanced audio connection. Its headline performance is 91 dB CMRR, which improves rejection of common-mode interference, and -120 dB THD+N under the stated 1 kHz, 22-dBu test condition. These figures make the device relevant to professional audio, industrial audio, and other balanced-line systems where low distortion and noise immunity are important. Its wide 4.5 V to 36 V supply range accommodates conventional analog audio rails as well as higher-voltage industrial interfaces. The operating-temperature range extends from -40 °C to +125 °C, supporting applications across consumer, industrial, and temperature-controlled equipment. The 14-pin TSSOP package also has a small board footprint while remaining compatible with standard surface-mount assembly methods. Typical uses include stereo balanced-line input stages, professional mixing equipment, studio monitor interfaces, industrial audio links, and instrumentation that receives differential signals through long cables. Because the receiver rejects common-mode voltage rather than improving it at the source, it should be paired with properly shielded or twisted-pair wiring and a low-impedance reference for the opposite input. A key implementation consideration is input and reference arrangement. The manufacturer datasheet should be used to assign each of the 14 pins, connect the signal and reference returns, decouple the supply, and preserve the recommended input network. PCB layout should keep sensitive audio traces away from switching nodes and high-current return paths so that the receiver's intrinsic 91 dB CMRR is not undermined by board-level coupling. This product record combines manufacturer specifications, package information, sourcing fields, and application-focused engineering guidance. It also distinguishes verified drop-in replacements from functionally related receiver or current-measurement devices, helping engineers avoid selecting a same-size package that is not actually pin-compatible.

RFQ تماس
INA1651IPWR - 91dB CMRR Audio Receiver | Texas Instruments
INA1651IPWR

INA1651IPWR - 91dB CMRR Audio Receiver | Texas Instruments

The Texas Instruments INA1651IPWR is a SoundPlus high common-mode-rejection differential audio line receiver with 91 dB CMRR, -120 dB THD+N at 1 kHz, and a 14-pin TSSOP (PW) package. It is designed for professional audio, instrumentation, and balanced-signal applications where common-mode interference and distortion must be tightly controlled. The INA1651 is a single-channel differential line receiver in the amplifier and signal-conditioning hierarchy. A differential receiver extracts the voltage difference between two signal conductors, while its CMRR specification indicates how effectively it rejects voltage shared equally by both inputs. The SoundPlus family is optimized for high-fidelity audio paths in which low total harmonic distortion plus noise is more valuable than simply minimizing quiescent current. Three headline operating characteristics define the device: 91 dB common-mode rejection, -120 dB total harmonic distortion plus noise at a 1 kHz test condition, and operation across a -40°C to +125°C temperature range. The exact 22-dBu signal level used for the published THD+N characterization and the wide ±18 V or 36 V total supply capability make the part relevant to balanced professional-audio equipment. Precision matching of the integrated resistors is central to maintaining CMRR performance. The INA1651 family uses matched on-chip resistors to improve common-mode rejection beyond what a conventional resistor-network differential receiver commonly achieves. The single-channel INA1651 is intended for balanced audio inputs, while the related dual-channel INA1650 serves systems requiring two receiver channels. This architecture makes the device useful in mixers, preamplifiers, recording equipment, instrument interfaces, and other systems that carry balanced signals over cables or through grounding-prone environments. Typical installations place the receiver at the input of an audio analog front end, followed by gain and conversion stages. In a mixer input, for example, the INA1651 can reject common-mode noise picked up by a balanced cable before the signal is amplified. Its -120 dB THD+N characteristic helps preserve low-level program material, while 91 dB CMRR helps prevent hum, ground-potential differences, and other shared-mode disturbances from being converted into differential signal errors. Designers should follow the manufacturer pin-description table when assigning input, output, supply, and enable functions. Keep sensitive audio traces short and use a ground-return arrangement that does not force signal current through the same impedance as the receiver reference. Confirm the selected package variant, supply limits, input and output voltage limits, and decoupling requirements in the manufacturer datasheet before releasing a PCB. This product page combines the INA1651's core audio-performance figures with application guidance, verified source links, package information, and practical selection context. It also highlights why CMRR, THD+N, supply range, and pin compatibility must be considered together when choosing a differential audio receiver for a new design.

RFQ تماس
INA166UA - G=2000 Low-Noise Instrumentation Amplifier | TI
INA166UA

INA166UA - G=2000 Low-Noise Instrumentation Amplifier | TI

The Texas Instruments INA166UA is a single-circuit, internally set G=2000 instrumentation amplifier with a 450 kHz -3 dB bandwidth, 15 V/µs slew rate, 50 µV input offset voltage, and 2.5 µA input bias current in a 14-pin SOIC (D) package. The device uses current-feedback circuitry to provide low noise, low distortion, wide bandwidth, and strong dynamic response when amplifying very small differential signals. An instrumentation amplifier is a differential-input amplifier optimized for precision signal conditioning. It combines high input impedance, accurate differential gain, and common-mode rejection into one device, reducing the need for several precision operational amplifiers and matched resistors. The INA166 belongs to the broader amplifier IC hierarchy and is commonly used where sensors and transducers produce small outputs that must be measured accurately in the presence of larger common-mode voltages. The INA166's fixed gain of 2000 increases a small differential input by a factor of 2000, making it useful for low-level microphone, hydrophone, industrial transducer, and medical-instrumentation signals. Its 450 kHz -3 dB bandwidth provides substantially more bandwidth than a traditional low-noise precision amplifier with a narrow frequency response. The 15 V/µs slew rate supports rapid signal transitions, while the 2.5 µA input bias current helps preserve accuracy with high-impedance sources. The current-feedback architecture differentiates the INA166 from voltage-feedback instrumentation amplifiers that depend on a closed-loop gain resistor. Because its gain is internally set, the circuit does not require an external gain-setting resistor, reducing component count and avoiding sensitivity to external gain-resistor tolerance. The manufacturer describes the device as a very low-noise, low-distortion monolithic instrumentation amplifier intended for low-level signals. Typical uses include precision microphone preamplification, hydrophone signal chains, industrial process-control inputs, bridge-sensor interfaces, and medical monitoring equipment. In each case, the differential input can reject common-mode interference while the fixed high gain converts a millivolt-level sensor output into a range suitable for an ADC or subsequent signal-processing stage. Designers should verify the signal bandwidth and output swing against the datasheet limits, place input and feedback connections for low noise, and provide stable bypassing on the supply pins. The wide bandwidth and slew rate can excite output-stage distortion if the output signal approaches the available output-voltage range, so the gain and sensor bandwidth should be considered together rather than independently. This product record combines the verified manufacturer and distributor data for the INA166UA with lifecycle information, pricing context, package details, application guidance, and a conservative replacement analysis. It distinguishes verified drop-in candidates from related ordering variants so engineers can assess PCB and supply-chain decisions without confusing a different gain option with an exact functional replacement.

RFQ تماس
INA181A1QDBVRQ1 - 26V AEC-Q100 Bidirectional Current Sense Amp | TI
INA181A1QDBVRQ1

INA181A1QDBVRQ1 - 26V AEC-Q100 Bidirectional Current Sense Amp | TI

The Texas Instruments INA181A1QDBVRQ1 is an AEC-Q100-qualified, 26V bidirectional, low- and high-side voltage-output current-sense amplifier with a fixed gain of 20 V/V, housed in a 6-pin SOT-23 (DBV) package. It operates across a -0.2V to 26V common-mode input range, supports a 350 kHz bandwidth, and draws 195 uA typical quiescent current. The A1 gain variant delivers 20 V/V output scaling, making it suitable for low-current shunt monitoring in tight PCB areas. A current-sense amplifier is an analog IC that measures voltage drop across a shunt resistor placed in series with a load, producing a ground-referenced output proportional to load current. Current-sense amplifiers sit in the broader hierarchy of signal-chain ICs -> amplifiers -> instrumentation amplifiers -> current-sense amplifiers, and they are essential building blocks of any power-management system that requires accurate real-time current telemetry for protection, regulation, or efficiency optimization. Key features include bidirectional sensing (single part supports both charge and discharge current on battery rails), 350 kHz bandwidth for fast transient response, rail-to-rail output swing for maximum dynamic range with low supply headroom, and AEC-Q100 Grade 1 qualification with an operating temperature range of -40C to +125C for under-hood automotive deployment. The device integrates a precision thin-film gain resistor network that eliminates external gain-setting components. Internally, the INA181A1QDBVRQ1 uses a chopped-input bipolar front-end with delta-sigma offset correction, achieving 100 uV maximum offset and 1 uV/C typical drift. This architecture rejects 50/60 Hz line-coupled noise and PSRR-induced errors from upstream switching converters, enabling accurate measurement on noisy automotive buses such as 12V battery feeds. Typical applications include automotive body electronics (lighting load monitoring, seat heater current sense), USB Type-C VBUS current monitoring, motor drive H-bridge phase current feedback, battery management systems for e-bikes and power tools, and solar MPPT input-side current sensing. The wide common-mode range handles inductive load transients and load-dump pulses found in 12V/24V automotive systems. When designing with this device, ensure the input pins remain within the absolute maximum ratings even during transients; a small differential RC filter between the shunt and the IN+/IN- pins limits input-stage overdrive. Use a 4-layer PCB with a low-impedance ground pour to avoid ground bounce corrupting the high-side measurement. This page synthesizes distributor pricing, drop-in SOT-23-6 alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ تماس
INA186A3IDCKR - 40V Bidirectional Current Sense Amp | TI
INA186A3IDCKR

INA186A3IDCKR - 40V Bidirectional Current Sense Amp | TI

The Texas Instruments INA186A3IDCKR is a 40 V, bidirectional, high-precision, low-power, zero-drift current-sense amplifier in a 6-pin SC-70 (DCK) package. The A3 gain variant sets the fixed internal gain to 100 V/V, and the device accepts common-mode voltages from -0.2 V to +40 V independently of the supply rail. A current-sense amplifier (CSA, also called a current-shunt monitor) is an analog IC that measures the small differential voltage developed across a shunt resistor in series with a load, and converts it to a ground-referenced output voltage proportional to load current. CSAs sit in the signal-chain hierarchy: shunt resistor -> current-sense amplifier -> ADC / MCU / comparator, and they are essential building blocks in the power-management sub-system for accurate telemetry and protection. Key features include a low offset voltage enabled by the zero-drift chopper architecture, picoamp-level input bias current that supports large shunt values for microamp measurements, a low quiescent current (typically tens of microamps) suitable for always-on battery monitoring, an integrated ENABLE pin for power gating, and rail-to-rail output swing for full-scale ADC input utilization. The A3 fixed gain of 100 V/V provides 20 mV/V sensitivity. The architecture combines a precision chopper-stabilized input stage with an internal gain-setting resistor network, eliminating the external gain resistors required by discrete difference-amplifier implementations. The high common-mode rejection and picoamp bias allow designers to use larger sense resistors for better signal-to-noise without measurable loading error. Typical applications include battery-cell monitoring in battery management systems (BMS), USB-C current advertisement and overcurrent protection, motor-phase current sensing in BLDC drivers, solar MPPT input-current telemetry, and precision 24 V industrial-sensor rails. Design tip: pick the A1/A2/A3/A4/A5 gain variant by matching your full-scale shunt voltage to the ADC input range; keep the shunt Kelvin-connected to the IN+/IN- pins and use a 4-wire layout to preserve CMRR at high dV/dt. This page consolidates authorized-distributor pricing for the INA186A3IDCKR, true drop-in alternatives in the same SC-70-6 footprint, and PCB design guidance that goes beyond the manufacturer datasheet.

RFQ تماس
INA188ID - 36V Zero-Drift Instrumentation Amplifier | Texas Instruments
INA188ID

INA188ID - 36V Zero-Drift Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA188ID is a single-channel, 36 V zero-drift instrumentation amplifier with rail-to-rail output, selectable gain from 1 to 1000, and an 8-pin SOIC package. It provides a gain of 1 + (50 kΩ/RG), allowing one external resistor to set the gain while preserving the established instrumentation-amplifier connection. According to the Texas Instruments product page, the INA188ID is intended for precision signal measurement and sensor conditioning, including temperature sensing and bridge-based measurements, and is specified over a -40°C to +125°C temperature range. An instrumentation amplifier is a specialized differential amplifier that measures a small voltage difference between two inputs while offering high input impedance, common-mode rejection, and gain accuracy. The INA188 belongs to the zero-drift instrumentation-amplifier family, a subtype of precision analog amplifiers used for sensor interfaces, current measurement, biomedical instrumentation, and industrial process control. Its internal auto-zeroing techniques reduce offset voltage and offset drift, making it more suitable for slowly varying precision signals than a conventional amplifier whose offset moves with temperature. Key features include a 36 V maximum supply voltage, rail-to-rail output operation, gains from 1 to 1000, and a maximum input offset voltage of 55 µV as reported by the comparative distributor data. The reference pin supports output level shifting in single-supply systems and offset calibration. A single gain-setting resistor simplifies design-in, while the zero-drift architecture addresses offset stability in temperature, bridge, and slow-current-measurement systems. The 8-pin SOIC package also supports conventional surface-mount assembly. The gain relationship G = 1 + (50 kΩ/RG) allows the sensor interface to be scaled without an active gain network. For example, a 1 kΩ gain resistor produces a nominal gain of 51, while a 50 Ω resistor produces a nominal gain of 1001 before rounding and standard gain-error considerations are applied. The reference input provides an additional analog node for systems that cannot shift their output entirely in the analog domain. Designers should preserve the instrumentation-amplifier grounding and input-common-mode requirements when evaluating usable signal range. Typical uses include strain-gauge and load-cell bridges, RTD and thermocouple signal conditioning, precision current-shunt measurements, battery monitoring, and low-level sensor acquisition. The INA188ID is particularly appropriate when low offset and low drift matter more than wideband response. In bridge systems, its differential input arrangement and adjustable gain can amplify the small bridge imbalance while limiting sensitivity to common-mode voltage. In battery-powered equipment, the reference pin can place the output within the usable range of a single-supply analog-to-digital converter. The primary design consideration is ensuring that input and output common-mode voltages remain inside the device's operating limits at every gain and supply condition. Gain-set resistor tolerance contributes directly to gain accuracy, so precision resistors may be required for calibrated measurements. Input filtering, source impedance, reference-pin routing, and exposed-area thermal management should also be evaluated before production release. This product page consolidates manufacturer specifications, verified distributor pricing, package details, comparison data, and practical design guidance. It also distinguishes verified drop-in candidates from broader functional alternatives so engineers can assess footprint, gain-setting, voltage-range, and precision differences before changing a production design.

RFQ تماس
INA188IDR - 36V Zero-Drift Instrumentation Amplifier | Texas Instruments (Tape & Reel)
INA188IDR

INA188IDR - 36V Zero-Drift Instrumentation Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments INA188IDR is a single-channel, 36 V zero-drift instrumentation amplifier with rail-to-rail output, selectable gain from 1 to 1000, and an 8-pin SOIC package. It provides a gain of 1 + (50 kΩ/RG), allowing one external resistor to set the gain while preserving the established instrumentation-amplifier connection. According to the Texas Instruments product page, the INA188IDR is intended for precision signal measurement and sensor conditioning, including temperature sensing and bridge-based measurements, and is specified over a -40°C to +125°C temperature range. An instrumentation amplifier is a specialized differential amplifier that measures a small voltage difference between two inputs while offering high input impedance, common-mode rejection, and gain accuracy. The INA188 belongs to the zero-drift instrumentation-amplifier family, a subtype of precision analog amplifiers used for sensor interfaces, current measurement, biomedical instrumentation, and industrial process control. Its internal auto-zeroing techniques reduce offset voltage and offset drift, making it more suitable for slowly varying precision signals than a conventional amplifier whose offset moves with temperature. Key features include a 36 V maximum supply voltage, rail-to-rail output operation, gains from 1 to 1000, and a maximum input offset voltage of 55 µV as reported by the comparative distributor data. The reference pin supports output level shifting in single-supply systems and offset calibration. A single gain-setting resistor simplifies design-in, while the zero-drift architecture addresses offset stability in temperature, bridge, and slow-current-measurement systems. The 8-pin SOIC package also supports conventional surface-mount assembly. The gain relationship G = 1 + (50 kΩ/RG) allows the sensor interface to be scaled without an active gain network. For example, a 1 kΩ gain resistor produces a nominal gain of 51, while a 50 Ω resistor produces a nominal gain of 1001 before rounding and standard gain-error considerations are applied. The reference input provides an additional analog node for systems that cannot shift their output entirely in the analog domain. Designers should preserve the instrumentation-amplifier grounding and input-common-mode requirements when evaluating usable signal range. Typical uses include strain-gauge and load-cell bridges, RTD and thermocouple signal conditioning, precision current-shunt measurements, battery monitoring, and low-level sensor acquisition. The INA188IDR is particularly appropriate when low offset and low drift matter more than wideband response. In bridge systems, its differential input arrangement and adjustable gain can amplify the small bridge imbalance while limiting sensitivity to common-mode voltage. In battery-powered equipment, the reference pin can place the output within the usable range of a single-supply analog-to-digital converter. The primary design consideration is ensuring that input and output common-mode voltages remain inside the device's operating limits at every gain and supply condition. Gain-set resistor tolerance contributes directly to gain accuracy, so precision resistors may be required for calibrated measurements. Input filtering, source impedance, reference-pin routing, and exposed-area thermal management should also be evaluated before production release. This product page consolidates manufacturer specifications, verified distributor pricing, package details, comparison data, and practical design guidance. It also distinguishes verified drop-in candidates from broader functional alternatives so engineers can assess footprint, gain-setting, voltage-range, and precision differences before changing a production design.

RFQ تماس
INA188IDRJR - 36V Zero-Drift Instrumentation Amplifier | Texas Instruments
INA188IDRJR

INA188IDRJR - 36V Zero-Drift Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA188IDRJR is a precision, zero-drift, rail-to-rail output, high-voltage instrumentation amplifier housed in an 8-pin SON (4x4 mm) package with an exposed thermal pad. It delivers 55 uV (max) input offset voltage, 0.2 uV/°C (max) input offset drift, and 104 dB (min) CMRR at gains of 10 or higher. The part operates from a wide 4 V to 36 V single supply (or ±2 V to ±18 V dual supply), accepting input signals up to the rails while swinging its output rail-to-rail. An instrumentation amplifier (INA) is a specialized differential amplifier designed for precise amplification of small differential signals in the presence of large common-mode voltages. Compared to a general-purpose op-amp built from three discrete amplifiers, an INA integrates the input buffer, gain stage, and difference amplifier into one laser-trimmed silicon block, achieving far higher common-mode rejection ratio (CMRR), lower offset drift, and far simpler single-resistor gain setting. INAs sit hierarchically inside the sensor signal-chain / analog front-end / mixed-signal IC family and are the building block of choice for bridge sensors, thermocouples, RTDs, and biomedical instrumentation. Key features include 12 nV/√Hz input voltage noise density at 1 kHz, 0.25 uVPP (0.1 Hz to 10 Hz) low-frequency noise, an industry-standard gain equation G = 1 + (50 kΩ / RG) settable from 1 V/V to 1000 V/V with a single external resistor, and a reference pin for level-shifting in single-supply operation or for offset calibration. The integrated zero-drift (chopper-stabilized) topology continuously nulls its own 1/f noise and offset, eliminating the need for periodic user calibration. The INA188 uses TI's proprietary auto-zero / chopper-stabilized architecture combined with thin-film resistor networks for the gain-setting feedback. This delivers near-ideal DC accuracy without the discrete capacitor or clock-noise artifacts of older chopper designs, while the 4 mm x 4 mm SON package exposes its complementary efficiency rating to standard SOIC-8 boards through its thermal pad. Typical applications include weigh scales and bridge sensor signal conditioning, thermocouple and RTD temperature measurement, medical instrumentation (ECG, EEG front ends), industrial process controls, and strain-gauge amplifier chains. The wide 4 V to 36 V supply range makes it a direct fit for industrial 24 V bus systems. When designing, place the gain-setting resistor close to the RG pins and add a 0.1 uF supply bypass capacitor on each supply pin; the exposed thermal pad must be soldered to a copper pad for rated thermal performance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ تماس
INA190A1IRSWR - 40V Picoamp Current Sense Amp | TI
INA190A1IRSWR

INA190A1IRSWR - 40V Picoamp Current Sense Amp | TI

The Texas Instruments INA190A1IRSWR is a 40V bidirectional, zero-drift current sense amplifier (current-shunt monitor) with picoampere input bias current and an enable pin, housed in a 10-pin UQFN (RSV, 1.8 mm x 1.4 mm) package. It senses voltage drops across shunt resistors at common-mode voltages from -0.2 V to +40 V, independent of its 1.8 V-class low supply. A current sense amplifier is a specialized difference amplifier that measures the small voltage generated across a shunt resistor and converts it into a ground-referenced output signal. Within the power-management hierarchy, it sits between the shunt and an ADC or comparator, enabling precise current measurement for feedback, protection, and telemetry in systems from battery packs to industrial drives. Key features of the INA190 family include a very wide input common-mode range (-0.2 V to 40 V) that tolerates inductive kickback and reverse-battery events, ultra-low input bias current in the picoampere range that permits very small shunt resistors, and zero-drift architecture for near-DC accuracy. The INA190A1IRSWR offers an ENABLE pin for power-cycling in battery-powered designs and operates across -40C to +125C. Technically, the device uses a zero-drift (auto-zeroing) topology that eliminates offset drift over time and temperature, achieving precision far beyond conventional CMOS amplifiers. The low bias current allows shunts in the milliohm range without significant self-heating error, while the wide common-mode range permits high-side, low-side, and bidirectional sensing with a single supply. The voltage-output interface connects directly to ADCs without external conditioning. Typical applications include overcurrent protection in USB and battery-powered systems, precision current telemetry in notebooks and IoT devices, and closed-loop current feedback in industrial controls, where low shunt losses and accuracy at low supply voltages are essential. Design consideration: because the part supports a 1.8 V supply domain, verify the output swing and reference pin drive against your ADC input range to avoid clipping near the rails. This page synthesizes distributor pricing, drop-in alternatives, pinout guidance, and practical design notes not found in the manufacturer datasheet.

RFQ تماس
INA190A2IDDFR - 40V Bidirectional Current Sense Amp | TI
INA190A2IDDFR

INA190A2IDDFR - 40V Bidirectional Current Sense Amp | TI

The Texas Instruments INA190A2IDDFR is a 40-V bidirectional, ultra-precise current-sense amplifier with picoamp-level input bias current and an integrated ENABLE pin, offered in an 8-pin TSOT-23 (DDF) package. The A2 gain option delivers a fixed 50 V/V transimpedance, supporting common-mode voltages from -0.2 V to +40 V independent of the supply rail. The zero-drift chopper-stabilized architecture keeps input offset voltage below 15 uV (typical 5 uV) and offset drift below 0.1 uV/C, which translates directly into accurate microamp-range current measurements when paired with a small shunt. A current-sense amplifier is an analog building block that converts a small differential voltage developed across a shunt resistor into a ground-referenced output voltage proportional to load current. The INA190 family belongs to the current-sense amplifier / instrumentation amplifier / signal-chain IC / analog IC taxonomy, sitting one level below general-purpose op-amps because it integrates a precision gain network and reference-stable input stage optimized for high common-mode rejection at high voltages. This category plays a central role in modern power management, where system optimization, telemetry, and closed-loop feedback demand accurate, low-latency current data. Key features include a 1.8-V to 5.5-V supply range, 65 uA typical quiescent current, 60 V common-mode transient immunity, and 40 kHz small-signal bandwidth. Output swings rail-to-rail and the device supports low-side, high-side, and bidirectional topologies, eliminating external protection circuitry in 12-V, 24-V, and 48-V industrial buses. The picoamp input bias current allows sense resistors up to tens of kilo-ohms, which is critical for monitoring sleep-mode current in battery-powered products without degrading accuracy. The zero-drift chopper architecture continuously nulls 1/f noise and thermal drift, yielding effectively DC-stable output over the full -40C to +125C operating range. The internal EN pin lets a microcontroller gate the supply current down to a sub-microamp leakage level, which is essential for always-on battery systems that must periodically wake to perform current sampling. Combined, these characteristics make the INA190A2 one of the lowest-noise, lowest-drift current-sense amplifiers in its class. Typical applications include USB-PD and Type-C cable-compensation, motor-control current loops, solar MPPT input monitors, battery-pack gas-gauging, and point-of-load telemetry in servers and telecom rectifiers. The fixed 50 V/V gain optimizes the part for low-current (sub-amp) measurements where the A1 (25 V/V) is too noisy and the A3 (100 V/V) or A4 (200 V/V) variants sacrifice dynamic range. A key design consideration is the trade-off between shunt resistance and dissipated power: choose a 50 V/V part when the load is typically below 1 A and milliohm shunts are preferred, and place the input capacitor network as close as possible to the IN+ and IN- pins to reject high-frequency transients on the common-mode bus. This page synthesizes distributor pricing, drop-in alternatives in the same TSOT-23-8 footprint, and practical design notes that go beyond the manufacturer datasheet to help engineers select, source, and qualify the INA190A2IDDFR for their next precision current-monitoring design.

RFQ تماس
INA210BQDCKRQ1 - AEC-Q100 26V Bi-Directional Current Sense Amp | TI
INA210BQDCKRQ1

INA210BQDCKRQ1 - AEC-Q100 26V Bi-Directional Current Sense Amp | TI

The Texas Instruments INA210BQDCKRQ1 is an AEC-Q100 qualified, 26 V, bi-directional, high-precision current sense amplifier (also called a current-shunt monitor) housed in a 6-pin SOT-SC70 (DCK) package. It senses voltage drops across shunt resistors at common-mode voltages from -0.3 V to 26 V, independent of the supply voltage, and delivers an analog output proportional to the sensed current with a fixed gain of 200 V/V. A current sense amplifier is a specialized analog building block that converts a small differential voltage developed across a current-sense (shunt) resistor into a ground-referenced, amplified output voltage. It sits in the signal chain between the shunt resistor (placed in series with the load) and the downstream ADC, microcontroller, or comparator, and belongs to the broader hierarchy of instrumentation amplifiers -> operational amplifiers -> analog ICs. Zero-drift chopper-stabilized topology enables the INA210 family to achieve microvolt-level offset and excellent common-mode rejection. Key features include a maximum offset voltage of 35 uV, a gain error of only 0.5 percent (max), and 40 kV/us slew rate, plus a 2.7 V to 26 V supply range with 65 uA typical quiescent current. The device offers bidirectional sensing (REF input allows positive or negative current measurement), operates from -40C to +125C, and integrates EMI filtering plus thermal shutdown. The SC70-6 package occupies roughly 2.1 mm x 1.45 mm of PCB area, ideal for compact automotive modules. The INA210 uses a chopper-stabilized input stage and precision thin-film resistors to achieve gain accuracy and ultra-low offset drift over temperature. Its high common-mode rejection ratio (CMRR) of 140 dB and the ability to operate with the input common-mode above V+ make it tolerant of inductive loads, motor inrush, and 12 V/24 V automotive transients such as load-dump. Typical applications include automotive body electronics (battery management, ECU power monitoring), motor control current loops, solenoid and valve actuation feedback, USB Type-C current advertisement (BC 1.2), and precision 48 V telecom/industrial rails. The combination of AEC-Q100 qualification, wide common-mode range, and small package makes it especially well-suited for safety-relevant automotive systems. When designing with this device, place the shunt resistor close to the input pins to minimize parasitic resistance, use Kelvin connection to the shunt, and add a small RC filter at the output to limit noise bandwidth. Choose the shunt value so that the maximum differential input (Vshunt_max = VSENSE_max / 200) does not exceed the linear input range, accounting for transient overloads. This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ تماس
INA2126E/250 - Dual 36V Micropower Instrumentation Amplifier
INA2126E/250

INA2126E/250 - Dual 36V Micropower Instrumentation Amplifier

Texas Instruments INA2126E/250 is a dual-channel, micropower precision instrumentation amplifier with 36 V maximum supply, 175 µA quiescent current per channel, and 250 µV maximum offset. The device is offered in a 16-pin SSOP package and is designed for low-noise differential-signal acquisition. It accepts operating supply voltages from ±1.35 V to ±18 V. An instrumentation amplifier is a specialized analog amplifier that measures the voltage difference between two input signals while rejecting common-mode interference. The INA2126 family uses a two-op-amp architecture to provide differential input, high input impedance, and straightforward gain selection with an external resistor. Within the signal-chain hierarchy, it belongs to the instrumentation-amplifier class, amplifier IC category, analog signal-conditioning family, and broader semiconductor category. The INA2126E/250 combines a 36 V supply range with low quiescent current, making it useful in portable instrumentation, battery-powered measurement systems, and industrial data-acquisition equipment. Its two amplifier channels can acquire independent differential signals, while the differential topology helps suppress common-mode voltage present on both inputs. Gain is established with an external resistor, allowing the circuit designer to select the required signal gain without changing the internal amplifier architecture. According to the Texas Instruments INAx126 family datasheet, the device uses a two-op-amp design and consumes 175 µA per channel. The low input bias current and high input impedance help prevent the source sensor from being heavily loaded. This is particularly important for high-impedance transducers, resistive sensors, and bridge-based measurements where input loading can otherwise change the detected voltage and degrade accuracy. Typical uses include low-voltage current sensing, portable medical instrumentation, industrial pressure and temperature acquisition, sensor-interface circuits, and precision differential measurement systems. The dual-channel configuration is useful when a design must monitor two related signals, such as a differential sensor output and a reference or diagnostic channel, while preserving independent gain-setting resistors for each amplifier. For stable operation, place supply-decoupling capacitors close to the supply pins and route each differential input as a compact pair to minimize noise pickup. Select the external gain resistor with suitable tolerance and low temperature coefficient, verify input and output common-mode limits at the intended supply voltage, and ensure the reference pin is driven with a low-impedance source when a nonzero midpoint voltage is required. This product page consolidates the device function, operating limits, package information, sourcing paths, drop-in family alternatives, comparison parameters, and practical circuit-design guidance. It supports faster engineering selection by connecting the INA2126E/250’s low-power precision characteristics with the signal-chain requirements of portable instrumentation and low-level differential-sensor designs.

RFQ تماس
INA2126P - Dual 36V Micropower Instrumentation Amplifier | Texas Instruments
INA2126P

INA2126P - Dual 36V Micropower Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2126P is a dual-channel, micropower precision instrumentation amplifier designed for accurate differential-signal acquisition. Each channel uses a two-op-amp architecture and consumes 175 µA of quiescent current, while the device operates from ±1.35 V to ±18 V, equivalent to a 36 V maximum total supply range. The INA2126P provides 250 µV offset performance and is supplied in a 16-pin PDIP package for through-hole PCB designs. An instrumentation amplifier is a specialized analog signal-conditioning IC that amplifies the voltage difference between two inputs while rejecting common-mode interference. The INA2126 family belongs to the instrumentation amplifier hierarchy, which includes differential amplifiers, low-noise analog amplifiers, and broader analog signal-chain ICs. Its differential-input architecture makes it suitable for sensor signals, bridge outputs, and other small-signal measurements where the wanted signal is small relative to an imposed common-mode voltage. The principal features of the INA2126P are its dual-channel configuration, 175 µA per channel quiescent current, 250 µV offset specification, and wide ±1.35 V to ±18 V operating range. Micropower consumption reduces the burden on portable and battery-powered systems, while the wide supply range supports both low-voltage portable instrumentation and higher-voltage industrial measurement systems. The differential architecture also helps preserve signal integrity when the input common-mode voltage is substantially larger than the differential signal being measured. The INA2126 family uses a two-op-amp instrumentation-amplifier topology to provide differential amplification with high input impedance and common-mode rejection. Because the device is intended for precision acquisition rather than high-bandwidth signal processing, designers should use the manufacturer-recommended gain-setting resistor and follow the datasheet layout guidance to minimize gain error and offset contributions. The 16-pin PDIP package favors through-hole prototyping, laboratory instrumentation, and industrial control boards where a surface-mount package is not required. Typical applications include portable sensor acquisition, strain-gauge and bridge excitation systems, battery-powered measurement equipment, industrial process monitoring, medical instrumentation, and low-power data-acquisition systems. In each case, the INA2126P provides a practical way to amplify a differential sensor signal while keeping channel quiescent current at 175 µA. Designers should confirm that input common-mode voltage, output swing, gain, bandwidth, and supply limits satisfy the specific measurement requirements. The primary design consideration is ensuring adequate output headroom and checking the gain-dependent bandwidth and input range. The 250 µV offset specification supports precise measurements, but resistor matching and layout still influence overall system accuracy. Input filtering and guarding can reduce high-frequency interference, while stable reference and excitation arrangements are important for bridge-based sensors. This product page combines the verified Texas Instruments product information, distributor availability references, pricing context, package details, and engineering selection guidance to provide a practical comparison point for engineers evaluating the INA2126P.

RFQ تماس