Texas Instruments

INA152EA/250 - 800 kHz Single-Supply Difference Amplifier | TI

MPN: INA152EA/250 ✓ فعال
Single supply Vdss 8-pin VSSOP (DGK), 0.118 in / 3.00 mm width Package
حداقل سفارش: 1 |

INA152EA/250 نمای کلی

The Texas Instruments INA152EA/250 is a single-supply, unity-gain difference amplifier with 800 kHz bandwidth, 1.5 mV input offset voltage, and 1 dB gain error, packaged in an 8-pin VSSOP (DGK). The device integrates a CMOS operational amplifier with a precision, laser-trimmed resistor network to measure small differential signals accurately in low-power instrumentation systems.

A difference amplifier is a specialized operational-amplifier configuration that rejects a voltage common to both inputs while amplifying their difference. The INA152 belongs to the precision analog signal-chain hierarchy: instrumentation amplifier, difference amplifier, operational amplifier, analog IC. Its integrated resistor network removes the need for an external matched resistor divider, simplifying current sensing, bridge excitation, and low-level front-end designs while preserving stable ratio behavior over temperature.

Important characteristics include a unity nominal gain, 0.01% gain accuracy from laser trimming, 800 kHz bandwidth, 1.5 mV input offset voltage, and 1 dB gain error. The INA152EA/250 operates across a -40 °C to +85 °C temperature range and is specified for an 8-VSSOP surface-mount package. Its integrated resistor network is designed for accurate common-mode rejection and gain stability across temperature.

The device uses a single-supply architecture, which simplifies analog signal acquisition where a negative supply is unavailable or undesirable. A single supply supports battery-powered, portable, industrial-sensor, and low-power test equipment designs. Because input and output headroom are constrained near the supply rails, the usable input and output common-mode ranges should be confirmed against the manufacturer datasheet for the exact operating voltage.

Typical uses include high-side or low-side current measurement, resistive sensor bridges, differential sensor interfaces, industrial process-control front ends, and low-power diagnostic instruments. The 800 kHz bandwidth is suitable for slow-to-moderate dynamic measurements rather than high-speed waveform capture. The integrated, trimmed network is particularly useful when maintaining accurate differential gain without calibrating several discrete resistors.

For board design, place the device close to the source node and route the differential inputs as a short, tightly coupled pair to minimize pickup of external noise. Connect the ground return directly to the source reference and use the pin-description table in the manufacturer datasheet when assigning PCB tracks. Verify supply decoupling, common-mode limits, output drive, and settling behavior in the application that sets the smallest signal of interest.

This page combines manufacturer specifications, package and ordering details, drop-in family alternatives, comparison parameters, and practical design guidance to support component selection, PCB planning, and precision analog front-end design.

جایگزین‌های drop-in برای INA152EA/250 — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

INA152EA/250G4

✅ جایگزین مستقیم
📦 8-VSSOP (DGK)
Same INA152 unity-gain electrical function and 8-VSSOP footprint; order-code suffix differs by 0% in gain, bandwidth, and package compatibility

📋 جایگزین مرجع (خارج از کاتالوگ)

INA152EA/2K5

✅ جایگزین مستقیم
📦 8-VSSOP (DGK)
Same 8-VSSOP footprint and family architecture, but nominal gain is 2.5 V/V versus 1 V/V, a 150% gain increase with lower output headroom

📋 جایگزین مرجع (خارج از کاتالوگ)

INA152UA/250

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-VSSOP (DGK)
Same unity gain and INA152 architecture in an 8-VSSOP family variant; package marking and order suffix differ by 0% in nominal gain

📋 جایگزین مرجع (خارج از کاتالوگ)

INA152UA/2K5

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-VSSOP (DGK)
Same 8-VSSOP family footprint, but nominal gain is 2.5 V/V versus 1 V/V, a 150% gain increase that requires output-headroom verification

📋 جایگزین مرجع (خارج از کاتالوگ)

INA152UA

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-VSSOP (DGK)
Same unity-gain single-supply INA152 function in the 8-VSSOP family; catalog suffix differs while nominal gain remains 1 V/V

📋 جایگزین مرجع (خارج از کاتالوگ)

INA152EA/250 حداکثر مقادیر مجاز و مشخصات الکتریکی

Amplifier Type Precision unity-gain difference amplifier
Number of Circuits 1 circuit
Supply Configuration Single supply
Nominal Gain 1 V/V
Bandwidth 800 kHz
Input Offset Voltage 1.5 mV
Gain Error 1 dB
Gain Accuracy 0.01% from laser-trimmed internal resistors
Resistor Network Integrated precision laser-trimmed resistor network
Operational Amplifier Core CMOS operational amplifier
محدوده دمای کاری -40 °C to +85 °C
بسته‌بندی 8-pin VSSOP (DGK), 0.118 in / 3.00 mm width
نوع نصب Surface mount
وضعیت RoHS Compliant
Safe Operating Area Not applicable to this amplifier IC

راهنمای پیکربندی پین INA152EA/250 8-pin vssop (dgk), 0.118 in / 3.00 mm width

پیکربندی پین برای INA152EA/250 (پکیج 8-pin vssop (dgk), 0.118 in / 3.00 mm width). این قطعه آنالوگ دارای پین‌های ورودی، خروجی و تغذیه است. برای پیکربندی‌های پین offset null، جبران‌سازی و فعال‌سازی به دیتاشیت سازنده مراجعه کنید. ایده‌آل برای مدارهای شرطی‌سازی سیگنال و تقویت‌کننده.

نمودار پین‌آوت پکیج 8-pin vssop (dgk), 0.118 in / 3.00 mm width برای INA152EA/250

داده پین‌آوت تفصیلی موجود نیست برای INA152EA/250.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

INA152EA/250 مناسب است برای 6 کاربردs: High-Side Current Sensing, Resistive Bridge Sensor Front End, Industrial Process-Control Input, Battery-Powered Portable Instrument, Precision Diagnostic Instrumentation, Low-Level Differential Sensor Interface.

⚡

High-Side Current Sensing

The INA152EA/250 fits high-side current measurement when the shunt voltage is small and the common-mode voltage must be rejected. Its unity gain of 1 V/V, 0.01% gain accuracy, and 1.5 mV input offset establish a predictable signal path from the shunt to an ADC or instrumentation stage. Place the amplifier beside the shunt and route the sense pair as a short differential connection. Check that the input common-mode voltage remains within the operating range and that output swing is sufficient at the selected supply voltage.

🌐

Resistive Bridge Sensor Front End

The INA152EA/250 is appropriate for Wheatstone-bridge outputs because its integrated, laser-trimmed resistor network maintains an accurate unity differential gain while rejecting excitation voltage common to both inputs. The 0.01% gain accuracy avoids the external-resistor mismatch that often limits discrete difference-amplifier implementations. Use a regulated excitation source, keep the bridge return and amplifier ground closely connected, and verify bias-current error for high-impedance sensors. The 800 kHz bandwidth supports sensor bandwidths well below its upper limit.

🏭

Industrial Process-Control Input

The INA152EA/250 can condition differential process signals in industrial control equipment while operating from a single supply, simplifying analog power planning. Its precision internal resistor ratio provides consistent unity gain, while the specified -40 °C to +85 °C range supports temperature-conditioned equipment. Place the input pair away from contactors, relays, and motor power stages, and use the reference arrangement defined by the manufacturer datasheet when the source is not ground-referenced. Confirm supply range, common-mode limits, and output swing for each analog input range.

📱

Battery-Powered Portable Instrument

The single-supply INA152EA/250 architecture suits portable instruments that cannot generate a negative analog rail. Its compact 8-pin VSSOP package and integrated gain-setting network reduce board area and external-component count. The device's low-power design basis is useful for energy-limited measurements, although the exact supply current should be confirmed from the datasheet for the selected operating mode. Use local decoupling and tightly coupled differential routing to preserve accuracy as battery voltage changes.

💊

Precision Diagnostic Instrumentation

The INA152EA/250 supports diagnostic instruments that measure small differential signals superimposed on larger common-mode voltages. Unity gain, 1.5 mV input offset, and the laser-trimmed 0.01% gain ratio provide predictable channel behavior. The 800 kHz bandwidth accommodates many sensor and bio-signal front ends without requiring a high-speed amplifier. Verify signal settling, noise performance, and common-mode limits in the final instrumentation configuration, and provide a stable reference return for the source under test.

🧩

Low-Level Differential Sensor Interface

The INA152EA/250 is useful when a sensor produces a millivolt-scale differential output and its common-mode voltage is much larger. The internal matched network establishes the unity-gain ratio and supports stable common-mode rejection, while the 800 kHz bandwidth leaves margin above most slow sensor response rates. Terminate or filter the input pair according to the source impedance, and check whether input bias current produces meaningful error. Keep sensitive traces away from switching converters and relay contacts.

خلاصه محصولات پیشنهادی

INA240A4DR Texas Instruments استفاده‌شده در: High-Side Current Sensing ADS8519IDR Successive-approximation ADC for digitizing the measured differential voltage استفاده‌شده در: High-Side Current Sensing, Resistive Bridge Sensor Front End, Industrial Process-Control Input, Precision Diagnostic Instrumentation ADS1131IDR Texas Instruments استفاده‌شده در: High-Side Current Sensing, Industrial Process-Control Input, Battery-Powered Portable Instrument, Low-Level Differential Sensor Interface ADS1262IPW Texas Instruments استفاده‌شده در: Resistive Bridge Sensor Front End, Precision Diagnostic Instrumentation, Low-Level Differential Sensor Interface INA152EA/2K5 Gain-2.5 family option when additional analog gain is required استفاده‌شده در: Resistive Bridge Sensor Front End, Battery-Powered Portable Instrument KSZ8895RQXI-TR Microchip Technology استفاده‌شده در: Industrial Process-Control Input INA152EA/250G4 Same-footprint unity-gain family alternative استفاده‌شده در: Low-Level Differential Sensor Interface
What is the INA152EA/250 differential amplifier used for?
The INA152EA/250 is a precision unity-gain difference amplifier for measuring the voltage difference between two inputs while rejecting their common component. Its integrated, laser-trimmed resistor network provides 0.01% gain accuracy, and its 800 kHz bandwidth suits current sensing, bridge sensors, and low-level industrial instrumentation. Texas Instruments describes it as a small, low-power, single-supply difference amplifier for systems that cannot conveniently generate a negative supply.
What are the key specifications of INA152EA/250 that engineers should know?
The INA152EA/250 provides a nominal gain of 1 V/V, 800 kHz bandwidth, 1.5 mV input offset voltage, 1 dB gain error, and 0.01% gain accuracy. It operates from a single supply and is specified from -40 °C to +85 °C in an 8-pin VSSOP (DGK). The manufacturer datasheet identifies a CMOS operational amplifier combined with a precision, laser-trimmed resistor network for accurate and stable differential gain.
Where can I download the INA152EA/250 datasheet PDF?
The official INA152EA/250 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ina152.pdf. It contains the electrical characteristics, pin description, typical application circuit, resistor-network behavior, common-mode limits, and thermal information for the INA152 family. The manufacturer product page for INA152 also provides ordering, quality, and part-detail information. Use those documents for the final PCB layout and worst-case analog performance checks.
Where can I find the INA152EA/250 pinout and pin descriptions?
The INA152EA/250 pin assignments are published in the pin-configuration section of the Texas Instruments INA152 datasheet. The device is an 8-pin VSSOP (DGK), and the manufacturer part-details page identifies the package as having 8 pins. Use the datasheet pin-description table when assigning supply, ground, input, output, and reference connections on the PCB rather than relying on a generic MSOP outline.
How do the INA152EA/250 and INA152EA/2K5 differ?
The INA152EA/250 has a nominal gain of 1 V/V, while the INA152EA/2K5 is the gain-2.5 variant in the same INA152 family and VSSOP (DGK) package. The /250 order code therefore suits applications where the differential signal should pass through near unity gain, while the /2K5 order code adds 2.5 times voltage gain. Both devices use the single-supply difference-amplifier architecture with an integrated precision resistor network.
When should I choose INA152EA/250 instead of INA152EA/2K5?
Choose INA152EA/250 when the desired differential gain is approximately one and downstream circuitry already performs filtering or further amplification. Choose INA152EA/2K5 when the same eight-pin footprint can provide 2.5 times the differential voltage and that additional gain fits the signal chain. Check output headroom carefully because the higher-gain variant reduces the allowable output swing for a given input signal, particularly in a single-supply design.
What is the best drop-in replacement for INA152EA/250?
The INA152EA/250G4 is the closest documented same-footprint member of the INA152 family, providing a unity-gain single-supply difference amplifier in the 8-pin VSSOP (DGK) format. Confirm the exact pin functions, supply range, temperature grade, and ordering suffix in the manufacturer documentation before substitution. A generic 8-pin precision difference amplifier may share the outline but can differ in gain, reference-pin behavior, input range, or output-drive capability, so package count alone does not establish interchangeability.
Can another manufacturer's difference amplifier replace INA152EA/250?
A cross-manufacturer replacement should be selected only after confirming pin-for-pin function, nominal gain, gain error, common-mode range, output swing, supply range, and stability. No cross-brand equivalent is listed on this page because the retrieved cross-reference results did not identify a verified drop-in device with those conditions. Compare the proposed part against the Texas Instruments datasheet and confirm the complete analog specification set before changing the PCB design.
Is INA152EA/250 suitable for single-supply current sensing?
The INA152EA/250 is suitable for many single-supply current-sensing front ends because it combines a unity gain of 1 V/V with an integrated matched resistor network and 0.01% gain accuracy. Place it across the shunt so the differential input stays within the amplifier's common-mode range and the output does not exceed the available output swing. Series input resistance, shunt placement, and Kelvin routing determine whether parasitics or thermocouple effects dominate the measurement.
Is INA152EA/250 suitable for bridge sensor measurement?
The INA152EA/250 can measure the small differential output of a resistive bridge because its precision internal ratio produces accurate unity gain and rejects the bridge excitation voltage appearing at both inputs. Signal-chain performance still depends on excitation regulation, bridge impedance, input bias current, and input common-mode headroom. For high-impedance bridges, verify bias-current error and whether an input biasing reference is required.
What is the best Texas Instruments equivalent for INA152EA/250?
The INA152EA/250G4 is the closest same-brand option located for a unity-gain, single-supply, 8-pin VSSOP implementation. It retains the INA152 family's integrated resistor-network approach, while the suffix and order-code details identify it as a distinct catalog item. If the INA152EA/2K5 is considered instead, note that its nominal gain is 2.5 V/V rather than 1 V/V, which changes downstream signal scaling and output headroom.
What can replace INA152EA/250 in a precision analog circuit?
The INA152EA/250G4 is the most direct replacement candidate because it preserves the family's unity gain, single-supply architecture, integrated precision resistor network, and 8-pin VSSOP format. Do not treat the INA152EA/2K5 as an automatic equivalent, since its gain is 2.5 rather than 1. For a different manufacturer, verify the complete pin function, electrical performance, and footprint rather than relying only on the eight-pin package count.
Is the INA152EA/250 the same as an ordinary precision op amp?
The INA152EA/250 is not simply a precision op amp; it is a complete unity-gain difference amplifier with an internal, laser-trimmed resistor network. That network establishes the differential gain ratio and improves gain stability and common-mode rejection. An ordinary precision op amp would normally require an external matched resistor divider and additional layout and tolerance management to achieve similar differential behavior.
How should INA152EA/250 inputs be routed on a PCB?
Route the two INA152EA/250 inputs as a short, tightly coupled differential pair from the sensed source, with the ground return connected to the source reference. Avoid long parallel runs beneath switching nodes or high-current conductors, and keep the amplifier close to the shunt or sensor. Use the datasheet pin table for final connections and confirm that input filtering resistors do not upset the intended gain accuracy or common-mode rejection.
Where can I buy INA152EA/250 online and what is its lead time?
Use the Request a Quote form on this page to request the current unit price, stock position, minimum order quantity, and lead time for INA152EA/250. Lead time and inventory can change with demand and packaging requirements, so request a firm quotation for the quantity and shipping destination. Texas Instruments also provides part-specific ordering and quality information through its official INA152 product page.

داده‌های مرجع مهندسی برای INA152EA/250 — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the INA152EA/250 when a small differential signal must be measured with a nominal gain of 1 V/V, particularly in a single-supply system where a negative rail is undesirable. Its 0.01% laser-trimmed resistor ratio, 1.5 mV offset rating, and 800 kHz bandwidth make it appropriate for shunt, bridge, and process-signal front ends. Choose the INA152EA/250G4 when an equivalent unity-gain catalog suffix is preferred for purchasing or inventory alignment. Choose the INA152EA/2K5 only when 2.5 times the differential voltage is desired and the resulting reduction in output headroom is acceptable. The UA variants belong to the same family and footprint family, but their exact suffix, temperature, and ordering details should be confirmed. For any different-manufacturer substitution, verify pin function, gain error, common-mode range, supply range, output swing, and stability rather than relying only on an eight-pin outline.

مقایسه با جایگزین‌ها

پارامتر این محصول INA152EA/250G4 INA152EA/2K5 INA152UA/250 INA152UA/2K5 INA152UA
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-VSSOP (DGK) 8-VSSOP (DGK) 8-VSSOP (DGK) 8-VSSOP (DGK) 8-VSSOP (DGK) 8-VSSOP (DGK)
Number of Pins 8 8 8 8 8 8
Amplifier Function Single-supply unity-gain difference amplifier Single-supply unity-gain difference amplifier Single-supply gain-2.5 difference amplifier Single-supply unity-gain difference amplifier Single-supply gain-2.5 difference amplifier Single-supply unity-gain difference amplifier
Nominal Gain 1 V/V 1 V/V 2.5 V/V 1 V/V 2.5 V/V 1 V/V
Resistor Network Integrated precision laser-trimmed network Integrated precision laser-trimmed network Integrated precision resistor network Integrated precision resistor network Integrated precision resistor network Integrated precision resistor network

تفاوت‌های کلیدی

  • Unity-gain transfer function preserves source scaling (در مقابلINA152EA/2K5)
  • Precision integrated resistor ratio reduces external matching requirements (در مقابلINA152UA/250)
  • Single-supply architecture simplifies portable analog systems (در مقابلINA152EA/2K5)

یادداشت‌های طراحی

Route the differential input pair as a short, tightly coupled trace from the source to the amplifier. Connect the amplifier ground reference to the source return rather than sharing a long path with digital or switching-current return wires. For shunt measurements, use a Kelvin connection so the sense traces carry only the amplifier input current. This arrangement limits parasitic pickup and prevents the voltage drop in a shared return trace from entering the measured difference.

Keep the INA152EA/250 away from switching nodes, relay contacts, and high-current conductors because its 1.5 mV input offset establishes a sensitive measurement scale. If series input resistors are required for transient protection or filtering, place them symmetrically and confirm that their parasitic resistance does not degrade differential gain accuracy. Use the manufacturer's pin-description table for the final input, reference, output, supply, and ground assignments.

Do not treat the 8-pin package outline as proof of interchangeability. The INA152EA/2K5 family variant has 2.5 V/V gain rather than the INA152EA/250's 1 V/V, which changes downstream scaling and reduces usable output headroom. Before any substitution, compare pin functions, nominal gain, gain error, offset voltage, common-mode range, output swing, supply range, temperature grade, and the manufacturer-recommended layout.

اطلاعات انطباق

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

RoHS-compliant status is identified in the INA152 series distributor listing. The INA152EA/250 is an industrial-temperature analog amplifier rather than an AEC-Q100 automotive-qualified device. Use the Texas Instruments product page and current material-compliance declarations for final procurement approval.

تاریخ تأیید داده‌ها: 2026-11-19 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

INA152EA/250 datasheet INA152EA/250 datasheet pdf INA152EA/250 pinout INA152EA/250 specifications INA152EA/250 price INA152EA/250 stock INA152EA/250 equivalent INA152EA/250 replacement INA152EA/250 vs INA152EA/2K5 INA152EA/250 VSSOP footprint INA152EA/250 current sensing Texas Instruments INA152EA/250

قطعات و اصطلاحات مرتبط

Texas Instruments INA152EA/250 INA152EA/250G4 INA152EA/2K5 INA152UA/250 INA152UA/2K5 INA152UA difference amplifier instrumentation amplifier precision operational amplifier CMOS operational amplifier laser-trimmed resistor network single-supply amplifier common-mode rejection unity gain 800 kHz bandwidth 1.5 mV input offset voltage 0.01% gain accuracy VSSOP-8 DGK package surface mount current sensing Wheatstone bridge industrial process control RoHS
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ