میکروکنترلرها

محصولات (20,000+)

ATSAM4N8AA-AU - 100MHz Cortex-M4 MCU, 512KB Flash | Microchip
ATSAM4N8AA-AU

ATSAM4N8AA-AU - 100MHz Cortex-M4 MCU, 512KB Flash | Microchip

The Microchip Technology ATSAM4N8AA-AU is a 32-bit ARM Cortex-M4 flash microcontroller running at up to 100 MHz with 512 KB of embedded flash memory and 64 KB of SRAM, housed in a 48-pin LQFP (7x7 mm) surface-mount package. It operates from 1.62 V to 3.6 V across the industrial temperature range. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest layer of the embedded-system hierarchy (MCU -> SoC -> application processor -> computer). The ARM Cortex-M4 core used here executes the Thumb-2 instruction set and includes DSP instructions for efficient digital signal processing plus a Memory Protection Unit (MPU) for robust RTOS deployments. Key differentiating features of the ATSAM4N8AA-AU include five USARTs, two SPI interfaces, and three I2C (TWI) controllers for fast serial communication, an 8-channel 12-bit ADC for analog sensing, PWM outputs, multiple timers, and a real-time clock (RTC). The 100 MHz Cortex-M4 with single-cycle MAC delivers roughly 125 DMIPS, providing DSP-class throughput in a low-power general-purpose MCU. Architecturally, the device belongs to Microchip's (formerly Atmel) SAM4N entry-point family within the broader SAM4 ARM Flash MCU portfolio. The flash-based program memory supports in-system programming via the Serial Wire Debug (SWD) or JTAG interface, and the MPU enables safe memory partitioning for FreeRTOS or Zephyr-class operating systems. Typical applications include industrial control panels, motor-adjacent sensing nodes, building automation controllers, and consumer appliances where multiple serial buses, ADC channels, and PWM channels must run concurrently under a single 3.3 V rail. Design consideration: supply the device from a clean 3.3 V rail (1.62 V to 3.6 V absolute range) and decouple each VDD pin with 100 nF ceramics; the ADC accuracy degrades with noisy supplies, so segregate analog grounding when using all 8 channels. This page synthesizes distributor pricing, drop-in family alternatives, pin-availability guidance, and practical design notes not found in the manufacturer datasheet alone. Pricing references are as of 2026-09-20.

RFQ تماس
ATSAM4N8AA-AUR - 100MHz Cortex-M4 MCU, 512KB Flash | Microchip (Tape & Reel)
ATSAM4N8AA-AUR

ATSAM4N8AA-AUR - 100MHz Cortex-M4 MCU, 512KB Flash | Microchip (Tape & Reel)

The Microchip Technology ATSAM4N8AA-AUR is a 32-bit ARM Cortex-M4 flash microcontroller running at up to 100 MHz with 512 KB of embedded flash memory and 64 KB of SRAM, housed in a 48-pin LQFP (7x7 mm) surface-mount package. It operates from 1.62 V to 3.6 V across the industrial temperature range. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest layer of the embedded-system hierarchy (MCU -> SoC -> application processor -> computer). The ARM Cortex-M4 core used here executes the Thumb-2 instruction set and includes DSP instructions for efficient digital signal processing plus a Memory Protection Unit (MPU) for robust RTOS deployments. Key differentiating features of the ATSAM4N8AA-AUR include five USARTs, two SPI interfaces, and three I2C (TWI) controllers for fast serial communication, an 8-channel 12-bit ADC for analog sensing, PWM outputs, multiple timers, and a real-time clock (RTC). The 100 MHz Cortex-M4 with single-cycle MAC delivers roughly 125 DMIPS, providing DSP-class throughput in a low-power general-purpose MCU. Architecturally, the device belongs to Microchip's (formerly Atmel) SAM4N entry-point family within the broader SAM4 ARM Flash MCU portfolio. The flash-based program memory supports in-system programming via the Serial Wire Debug (SWD) or JTAG interface, and the MPU enables safe memory partitioning for FreeRTOS or Zephyr-class operating systems. Typical applications include industrial control panels, motor-adjacent sensing nodes, building automation controllers, and consumer appliances where multiple serial buses, ADC channels, and PWM channels must run concurrently under a single 3.3 V rail. Design consideration: supply the device from a clean 3.3 V rail (1.62 V to 3.6 V absolute range) and decouple each VDD pin with 100 nF ceramics; the ADC accuracy degrades with noisy supplies, so segregate analog grounding when using all 8 channels. This page synthesizes distributor pricing, drop-in family alternatives, pin-availability guidance, and practical design notes not found in the manufacturer datasheet alone. Pricing references are as of 2026-09-20.

RFQ تماس
ATSAM4N8AA-MU - 100MHz Cortex-M4 MCU | Microchip | Industrial
ATSAM4N8AA-MU

ATSAM4N8AA-MU - 100MHz Cortex-M4 MCU | Microchip | Industrial

Microchip Technology ATSAM4N8AA-MU is a 32-bit ARM Cortex-M4 microcontroller with a maximum operating frequency of 100 MHz, 512 KB of embedded Flash memory, 64 KB of SRAM, and a 48-QFN 7 mm × 7 mm package. It integrates five USARTs, two SPI interfaces, three I²C interfaces, and an 8-channel 12-bit ADC for connected industrial, consumer, appliance, and energy-metering systems. An ARM Cortex-M4 microcontroller belongs to the microcontroller hierarchy of embedded semiconductors. The Cortex-M4 core combines a 32-bit processing architecture, DSP instructions, a Memory Protection Unit, and the Thumb-2 instruction set. These features support efficient real-time control while providing basic digital signal-processing capability without requiring a separate DSP or higher-cost application processor. Key device features include 512 KB of embedded Flash for firmware and data storage, 64 KB of SRAM for working memory, and a 100 MHz maximum clock frequency. The communication peripherals include five USARTs for serial links, two SPI controllers for synchronous buses, and three I²C controllers for low-pin-count peripheral connections. The integrated ADC provides eight channels with 12-bit resolution for analog measurement and control. The SAM4N family is positioned for applications that need a capable Cortex-M4 core together with multiple serial interfaces and mixed signal inputs. Its combination of five USARTs, two SPI interfaces, and three I²C interfaces can consolidate communication tasks that would otherwise require several discrete interface controllers. The 512 KB Flash capacity also provides more room for embedded application code than many entry-level microcontrollers. Typical uses include industrial automation equipment, appliance controllers, energy meters, consumer products, and connected embedded systems. The 48-QFN 7 mm × 7 mm package supports compact board layouts, while the assortment of serial peripherals is useful for sensor networks, actuator interfaces, display peripherals, external data storage, and service ports. The exact peripheral-sharing and electrical limits should be confirmed in the manufacturer datasheet for the selected board configuration. Designers should follow the manufacturer guidance for power, decoupling, clock, and exposed-pad layout. The QFN thermal pad must be connected according to the package drawing, and the board must provide low-impedance return paths for high-frequency signals. Firmware should also allocate SRAM carefully and verify which timers, DMA channels, serial interfaces, and analog inputs can operate simultaneously at 100 MHz. This page consolidates verified manufacturer and distributor information, documented communication resources, package information, sourcing data, and practical migration guidance. It also identifies where pin-level details, lifecycle metadata, or true drop-in alternatives must be verified directly with Microchip before a production design is released.

RFQ تماس
ATSAM4N8AA-MUR - 100MHz Cortex-M4 MCU | Microchip | Industrial (Tape & Reel)
ATSAM4N8AA-MUR

ATSAM4N8AA-MUR - 100MHz Cortex-M4 MCU | Microchip | Industrial (Tape & Reel)

Microchip Technology ATSAM4N8AA-MUR is a 32-bit ARM Cortex-M4 microcontroller with a maximum operating frequency of 100 MHz, 512 KB of embedded Flash memory, 64 KB of SRAM, and a 48-QFN 7 mm × 7 mm package. It integrates five USARTs, two SPI interfaces, three I²C interfaces, and an 8-channel 12-bit ADC for connected industrial, consumer, appliance, and energy-metering systems. An ARM Cortex-M4 microcontroller belongs to the microcontroller hierarchy of embedded semiconductors. The Cortex-M4 core combines a 32-bit processing architecture, DSP instructions, a Memory Protection Unit, and the Thumb-2 instruction set. These features support efficient real-time control while providing basic digital signal-processing capability without requiring a separate DSP or higher-cost application processor. Key device features include 512 KB of embedded Flash for firmware and data storage, 64 KB of SRAM for working memory, and a 100 MHz maximum clock frequency. The communication peripherals include five USARTs for serial links, two SPI controllers for synchronous buses, and three I²C controllers for low-pin-count peripheral connections. The integrated ADC provides eight channels with 12-bit resolution for analog measurement and control. The SAM4N family is positioned for applications that need a capable Cortex-M4 core together with multiple serial interfaces and mixed signal inputs. Its combination of five USARTs, two SPI interfaces, and three I²C interfaces can consolidate communication tasks that would otherwise require several discrete interface controllers. The 512 KB Flash capacity also provides more room for embedded application code than many entry-level microcontrollers. Typical uses include industrial automation equipment, appliance controllers, energy meters, consumer products, and connected embedded systems. The 48-QFN 7 mm × 7 mm package supports compact board layouts, while the assortment of serial peripherals is useful for sensor networks, actuator interfaces, display peripherals, external data storage, and service ports. The exact peripheral-sharing and electrical limits should be confirmed in the manufacturer datasheet for the selected board configuration. Designers should follow the manufacturer guidance for power, decoupling, clock, and exposed-pad layout. The QFN thermal pad must be connected according to the package drawing, and the board must provide low-impedance return paths for high-frequency signals. Firmware should also allocate SRAM carefully and verify which timers, DMA channels, serial interfaces, and analog inputs can operate simultaneously at 100 MHz. This page consolidates verified manufacturer and distributor information, documented communication resources, package information, sourcing data, and practical migration guidance. It also identifies where pin-level details, lifecycle metadata, or true drop-in alternatives must be verified directly with Microchip before a production design is released.

RFQ تماس
ATSAM4N8BA-AU - 100MHz Cortex-M4 MCU, 512KB Flash | Microchip
ATSAM4N8BA-AU

ATSAM4N8BA-AU - 100MHz Cortex-M4 MCU, 512KB Flash | Microchip

The Microchip Technology ATSAM4N8BA-AU is a 32-bit ARM Cortex-M4 microcontroller running at 100 MHz with 512 KB flash memory and 64 KB SRAM, housed in a 64-pin LQFP (10 x 10 mm) surface-mount package. It operates from a 1.62V to 3.6V supply and integrates six USARTs, three SPIs, and three I2C interfaces for high-speed serial communication. A microcontroller (MCU) is a single-chip embedded computer that combines a processor core, program memory, data memory, and peripherals on one die. Within the embedded hierarchy, the ATSAM4N8BA-AU belongs to the SAM4N family of ARM Cortex-M4-based microcontrollers, which sit under the broader categories of 32-bit MCUs, embedded processors, and system-on-chip devices used in industrial automation, consumer appliances, and energy metering. Key features include a 10-channel 12-bit ADC for accurate analog acquisition, a 10-bit DAC for waveform generation, PWM channels for motor and power control, general-purpose timers, and a real-time clock (RTC) for timekeeping in battery-backed systems. The Cortex-M4 core delivers single-cycle multiply-accumulate DSP instructions and hardware floating-point capability, allowing digital filtering and control-loop math to run efficiently at 100 MHz without an external DSP. Architecturally, the SAM4N series balances performance and low power consumption, making it well suited for always-on metering and automation nodes. According to the Microchip SAM4N family datasheet (60001422B), the series offers pin-to-pin compatibility with SAM4S, SAM3S, SAM3N, and SAM7S devices, enabling straightforward migration within the portfolio as memory or performance requirements change. Typical applications include industrial automation controllers, energy meters, consumer appliances, IoT sensor nodes, and motor control boards, where the combination of multiple USART/SPI/I2C buses, a 12-bit ADC, and PWM outputs covers most sensing and actuation needs from a single chip. A key design consideration is supply filtering: with a 1.62V to 3.6V operating range, decouple each VDD pin with 100 nF ceramics placed close to the package, and keep the analog supply pin fed through an RC filter from the main 3.3V rail to preserve ADC accuracy. This page synthesizes verified distributor pricing, pin-compatible drop-in alternatives across the SAM4N, SAM4S, and SAM3S families, and practical design notes not found in the manufacturer datasheet alone.

RFQ تماس
ATSAM4N8BA-AUR - 100MHz Cortex-M4 MCU 512KB Flash | Microchip
ATSAM4N8BA-AUR

ATSAM4N8BA-AUR - 100MHz Cortex-M4 MCU 512KB Flash | Microchip

The Microchip Technology ATSAM4N8BA-AUR is a 32-bit ARM Cortex-M4 microcontroller running at 100 MHz with 512 KB flash and 64 KB SRAM, housed in a 64-pin LQFP (10x10 mm) surface-mount package rated for industrial temperature ranges. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and peripherals into one chip, forming the lowest layer of the embedded-computing hierarchy: semiconductor -> microcontroller (MCU) -> embedded system. The ARM Cortex-M4 core used here is a 32-bit RISC processor optimized for deterministic real-time control, placing the ATSAM4N8B within Microchip's SAM4N family of general-purpose flash MCUs. Key features of the ATSAM4N8BA-AUR include 512 KB (512K x 8) of embedded flash memory for code and data storage, 64 KB of SRAM for runtime variables, and a rich peripheral set for communication: six USARTs, three SPIs, and three I2C interfaces. These serial resources make the device well suited to designs that must talk to multiple external ICs simultaneously. Technical depth comes from the Cortex-M4 architecture, which provides single-cycle multiply-accumulate DSP instructions and fast interrupt handling, allowing the 100 MHz core to handle both control loops and moderate signal processing without an external DSP. One integrated 10-channel 1 Msps-class ADC (per Microchip product data) offloads analog-to-digital conversion from external components. Typical applications include industrial automation nodes, motor control and sensor-hub boards, consumer appliance controllers, and multi-bus communication gateways that exploit the six USARTs and three SPI ports. A key design consideration is the industrial temperature rating (-40C to +85C per distributor data): confirm your worst-case ambient and self-heating stay within this window, and verify supply requirements in the manufacturer datasheet before finalizing power-tree design. This page synthesizes distributor pricing, drop-in family alternatives, comparison tables, and practical design notes not found in the standard manufacturer datasheet, providing engineers with a decision-ready product profile.

RFQ تماس
ATSAM4N8BA-MU - 100MHz Cortex-M4 512KB Flash MCU | Microchip
ATSAM4N8BA-MU

ATSAM4N8BA-MU - 100MHz Cortex-M4 512KB Flash MCU | Microchip

The Microchip Technology ATSAM4N8BA-MU is a 32-bit ARM Cortex-M4 flash microcontroller running at 100 MHz with 512KB of flash memory and 64KB of SRAM, housed in a 64-pin QFN (9x9 mm) package with exposed pad. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest level of the embedded computing hierarchy: MCU -> embedded processor -> microprocessor system. The SAM4N family sits within Microchip (formerly Atmel) ARM-based flash MCU portfolio as its entry point to the Cortex-M4 class, and is pin-to-pin compatible with the SAM4S, SAM3S, SAM3N and SAM7S families, which enables straightforward migration within the portfolio. Key features include six USARTs, three SPI interfaces and three I2C interfaces for high-speed serial communication, a 10-channel 12-bit ADC, a 10-bit DAC, PWM outputs, timers and an RTC. The device operates from a single 1.62V to 3.6V supply and is rated for industrial temperature ranges, with a green, RoHS-compliant package. Technically, the ARM Cortex-M4 core delivers efficient 32-bit computation with deterministic interrupt handling, while the generous serial connectivity (six USARTs plus three SPI plus three I2C) makes the device well suited to multi-protocol designs that would otherwise require external communication controllers. The 10-channel, 12-bit ADC supports multi-sensor front ends, and the complementary 10-bit DAC enables closed-loop analog control without external conversion ICs. Typical applications include industrial automation, consumer and appliance control, energy metering, and smart-home IoT nodes - all domains where the SAM4N family's balance of 100 MHz performance, low power consumption, and rich peripherals fits directly, according to the Microchip SAM4N family datasheet (document 60001422B). When designing with this device, keep the 1.62V to 3.6V supply range in mind for battery-powered designs, and use the exposed pad of the 64-QFN package as the ground return to improve thermal and signal-integrity performance. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ تماس
ATSAM4N8BA-MUR - 100MHz Cortex-M4 MCU 512KB Flash | Microchip
ATSAM4N8BA-MUR

ATSAM4N8BA-MUR - 100MHz Cortex-M4 MCU 512KB Flash | Microchip

The Microchip Technology ATSAM4N8BA-MUR is a 32-bit ARM Cortex-M4 microcontroller running at 100 MHz with 512KB of flash memory and 64KB of SRAM, housed in a 64-pin QFN (9x9 mm) package with exposed pad. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and peripherals into one chip, forming the lowest level of the embedded processing hierarchy: microcontroller unit (MCU) -> embedded processor -> microprocessor -> computing system. The SAM4N family belongs to Microchip's (formerly Atmel) SAM4 line of ARM Cortex-M4-based flash MCUs, targeting cost-sensitive embedded control applications that need 32-bit performance without floating-point heavy workloads. Key features of the ATSAM4N8B device include six USARTs, three SPI interfaces, and three I2C/TWI interfaces for fast serial communication, plus a 10-channel 12-bit ADC, a 10-bit DAC, PWM channels, timers, and a real-time clock (RTC). The supply range of 1.62V to 3.6V allows direct battery operation from single-cell lithium chemistry or 3.3V industrial rails. Architecturally, the ARM Cortex-M4 core at 100 MHz delivers approximately 125 DMIPS with single-cycle multiply and hardware division, while the 512KB single-cycle flash and 64KB SRAM support large protocol stacks and data buffers typical of industrial gateways and sensing nodes. Typical applications include industrial automation nodes, motor control and PWM-driven power stages, sensor hubs using the 12-bit ADC, and building/HVAC controllers that rely on the RTC and multiple serial ports. Design consideration: the QFN exposed pad is the main ground/thermal path and must be soldered to a solid ground pour; also budget supply decoupling across all VDD/VDDIO pairs given the multi-rail 1.62V to 3.6V architecture. This page synthesizes distributor pricing (as of 2026-09-20), drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ تماس
ATSAM4N8CA-AU - 100MHz Cortex-M4 MCU 512KB Flash | Microchip
ATSAM4N8CA-AU

ATSAM4N8CA-AU - 100MHz Cortex-M4 MCU 512KB Flash | Microchip

The Microchip Technology ATSAM4N8CA-AU is a 32-bit ARM Cortex-M4 microcontroller running at up to 100 MHz with 512 KB of embedded Flash and 64 KB of SRAM, housed in a 100-pin LQFP (14x14 mm) package. A microcontroller (MCU) is a single-chip computer integrating a processor core, program memory, data memory, and peripherals on one die. Within the power-management hierarchy of embedded systems, an MCU sits at the application layer, replacing multi-chip processor-plus-peripheral designs. The SAM4N family belongs to Microchip's (formerly Atmel's) ARM-based 32-bit Flash MCU portfolio, positioned as the reduced-BOM-cost entry point to the Cortex-M4 line. Key features include the ARM Cortex-M4 core with DSP instructions and Thumb-2 instruction set, a Memory Protection Unit (MPU), and pin-to-pin compatibility with the SAM4S, SAM3S, SAM3N, and SAM7S families for easy migration. According to the SAM4N family datasheet, this pin-compatibility makes ATSAM4N8CA-AU an ideal migration path from SAM4S designs that require lower cost. Technically, the device combines a Harvard-architecture Cortex-M4 running Thumb-2 code with single-cycle DSP multiply-accumulate instructions, delivering DSP-class throughput without a separate DSP. Embedded Flash allows in-system reprogramming, while the MPU supports robust, partitioned firmware. The 100-LQFP package provides generous GPIO and peripheral access for industrial designs. Typical applications include industrial automation, consumer and appliance control, and energy metering, markets explicitly targeted by the SAM4N series because of its low power consumption and peripheral integration. Design consideration: the device operates from 2.5 V to 3.3 V supply; verify supply rails and decoupling against the SAM4N datasheet electrical characteristics before layout. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ تماس
ATSAM4N8CA-AUR - 100MHz Cortex-M4 MCU 512KB Flash | Microchip
ATSAM4N8CA-AUR

ATSAM4N8CA-AUR - 100MHz Cortex-M4 MCU 512KB Flash | Microchip

The Microchip Technology ATSAM4N8CA-AUR is a 32-bit ARM Cortex-M4 microcontroller running at 100 MHz with 512 KB embedded Flash and 64 KB SRAM, housed in a 100-pin LQFP (14 x 14 mm) package delivered on tape and reel. A microcontroller (MCU) is a single-chip computer that integrates a processor core, memory, and peripherals on one die, forming the lowest layer of the embedded-system hierarchy: MCU -> embedded processor -> system-on-chip -> computing platform. The SAM4N family belongs to Microchip (formerly Atmel) SMART ARM-based MCU portfolio and targets cost-optimized industrial and consumer designs that still need 32-bit processing headroom. Key features include DSP instructions and a Thumb-2 instruction set on the Cortex-M4 core, a Memory Protection Unit (MPU) for robust firmware partitioning, and rich serial connectivity: seven USARTs, four SPIs, and three I2C (TWI) interfaces for fast peripheral communication. Analog capability covers a 16-channel 12-bit ADC and a 10-bit DAC, complemented by PWM channels, timers, and an RTC for real-time clocked applications. The device operates from a 1.62V to 3.6V supply, supporting both 1.8V and 3.3V systems. Architecturally, the SAM4N is the ideal migration path from the SAM4S for applications requiring reduced BOM cost, and it offers pin-to-pin compatibility with Atmel SAM3S, SAM3N, and SAM7S devices in the same packages, which simplifies in-portfolio upgrades without PCB redesign. Typical applications include industrial control panels, sensor hubs and data loggers exploiting the 16-channel ADC, motor and lighting control using PWM and timers, and building automation nodes that leverage the multiple USART/SPI/I2C ports. Design consideration: run the core at 100 MHz from a 3.3V rail and budget decoupling on all VDD/VDDIO pairs; the LQFP-100 footprint also leaves room to drop in higher-memory SAM4N16C variants later. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ تماس
ATSAM4N8CA-CFU - 100MHz Cortex-M4 512KB MCU | Microchip
ATSAM4N8CA-CFU

ATSAM4N8CA-CFU - 100MHz Cortex-M4 512KB MCU | Microchip

The Microchip Technology ATSAM4N8CA-CFU is a 32-bit ARM Cortex-M4 flash microcontroller running at 100 MHz with 512KB (512K x 8) of embedded Flash and 64KB (64K x 8) of SRAM, housed in a 100-ball VFBGA (7x7 mm) package for industrial temperature ranges. A microcontroller unit (MCU) is a single-chip embedded computer that integrates a processor core, non-volatile program memory, RAM, and a rich set of peripherals onto one die. Within the power-management hierarchy of embedded systems, the SAM4N family sits in Atmel/Microchip's entry-point segment of the Cortex-M4-based Flash MCU portfolio, positioning itself below the SAM4S while remaining pin-to-pin compatible with the SAM3S, SAM3N and SAM7S families. Key features include the ARM Cortex-M4 core with DSP-capable instructions, a supply voltage window of 1.62V to 3.6V (with an internal 1.2V core regulator), 100 MHz maximum core speed, 512KB of on-chip Flash for firmware, and a reduced-BOM-cost peripheral set tailored for cost-sensitive industrial designs. The -C temperature suffix denotes an industrial temperature grade, and the package is lead-free, green (halogen concern free) with MRL compliance per Microchip's product pages. Technically, the device leverages the Cortex-M4 3-stage pipeline Harvard architecture with a nested vectored interrupt controller (NVIC), single-cycle multiply, and Thumb-2 instruction set. Compared with the SAM4S family, the SAM4N removes USB and some analog blocks to reduce cost, making it the ideal migration path when a SAM4S design does not need those features. Typical applications include industrial control nodes, consumer appliances, metering front-ends, and general-purpose embedded control where 512KB Flash and the compact 7x7 mm VFBGA footprint support space-constrained PCB designs. A key design consideration: the VFBGA ball grid array requires controlled-impedance, fine-pitch PCB fabrication and X-ray inspection capability; verify your contract manufacturer supports 0.8 mm pitch BGA assembly before committing to this package. This page synthesizes distributor pricing links, drop-in cross-references within the SAM4N/SAM3S/SAM4S families, and practical packaging and assembly notes not consolidated in the manufacturer datasheet.

RFQ تماس
ATSAM4N8CA-CU - 100MHz Cortex-M4 512KB MCU | Microchip
ATSAM4N8CA-CU

ATSAM4N8CA-CU - 100MHz Cortex-M4 512KB MCU | Microchip

The Microchip Technology ATSAM4N8CA-CU is a 32-bit ARM Cortex-M4 microcontroller running at up to 100 MHz with 512 KB of embedded Flash and 64 KB of SRAM, housed in a 100-ball TFBGA (9x9 mm) package. An ARM Cortex-M4-based flash microcontroller is a compact system-on-chip that combines a 32-bit RISC processor core with non-volatile program memory, static RAM, and a rich set of peripherals on a single die. Within the power-management hierarchy of embedded systems, it occupies the general-purpose MCU tier, sitting between entry-level Cortex-M0/M0+ MCUs and higher-performance Cortex-M7 devices. The Cortex-M4 core adds a hardware FPU-class DSP instruction set, single-cycle MAC, and a Memory Protection Unit (MPU), executing the Thumb-2 instruction set. Key differentiating features include the 512 KB zero-wait-state-capable embedded Flash, 64 KB SRAM for buffers and stacks, a multi-layer bus matrix, and cost-optimized peripheral set aimed at the SAM4N family position as the entry point to Microchip's Cortex-M4 flash MCU portfolio. The industrial temperature rating and green, MSL-controlled TFBGA package support demanding assembly flows. Technically, the SAM4N implements the ARMv7E-M architecture with DSP extension instructions that accelerate filter loops and control algorithms common in embedded sensing. The on-chip ADC, multiple serial interfaces (USART, SPI, TWI), timers, and PWM channels allow single-chip designs that previously required external analog and communication components, reducing BOM cost. According to the manufacturer documentation, the SAM4N series offers pin-to-pin compatibility with Atmel SAM3S, SAM3N, and SAM7S devices, easing migration within the portfolio and serving as a cost-reduced migration path from the SAM4S. Typical applications include industrial control and automation nodes, consumer appliance control panels, metering front ends, and embedded sensing systems that need DSP-class math at 100 MHz without the cost of the SAM4S family. A key design consideration is power distribution: the device uses a 1.2V core with 3.3V I/O, so core supply regulation and decoupling per the datasheet ball map must be followed carefully. Verify Flash wait-state settings against the 100 MHz maximum clock. This page synthesizes distributor pricing, drop-in family alternatives, and practical design guidance not found in a single manufacturer document.

RFQ تماس
ATSAM4N8CA-CUR - 100MHz Cortex-M4 512KB Flash MCU | Microchip
ATSAM4N8CA-CUR

ATSAM4N8CA-CUR - 100MHz Cortex-M4 512KB Flash MCU | Microchip

The Microchip Technology ATSAM4N8CA-CUR is a 32-bit ARM Cortex-M4 microcontroller running at up to 100 MHz with 512 KB of embedded Flash and 64 KB of SRAM, housed in a 100-ball TFBGA (9x9 mm) package for industrial temperature ranges. A microcontroller (MCU) is a single-chip computer integrating a processor core, memory, and peripherals on one die. The ATSAM4N8CA belongs to the SAM4N family of ARM Cortex-M4-based MCUs, which sits within the broader hierarchy of 32-bit microcontrollers -> ARM embedded processors -> semiconductor integrated circuits. The SAM4N series is positioned as a reduced-BOM-cost migration path from the SAM4S family for cost-sensitive embedded designs. Key features include the ARM Cortex-M4 core with DSP instructions and Thumb-2 instruction set, a Memory Protection Unit (MPU), and 512 Kbytes of on-chip Flash with 64 Kbytes of SRAM. These DSP extensions accelerate filtering and control math, while the MPU supports functional-safety-oriented software partitioning. The 100 MHz clock delivers roughly 125 DMIPS-class performance for real-time embedded control. Architecturally, the device leverages Atmel/Microchip's SAM4 platform with an advanced interrupt controller, multi-layer bus matrix, and low-power modes typical of the SAM4 family, enabling efficient peripheral servicing and reduced active power consumption in battery-aware or always-on industrial nodes. Typical applications include industrial automation and control nodes, consumer and building-control systems, and data-logging or sensor-hub designs where 512 KB of code space and a 9x9 mm BGA footprint justify a high-integration MCU. When designing with this part, note that the fine-pitch TFBGA balls demand controlled-impedance, high-density PCB fabrication; confirm your assembly house supports 0.8 mm-pitch BGA placement before layout. This page synthesizes distributor pricing, drop-in alternatives, pin-count guidance, and practical design notes not consolidated in the manufacturer datasheet.

RFQ تماس
ATSAM4S16BA-AN - 120MHz Cortex-M4, 1MB Flash MCU | Microchip
ATSAM4S16BA-AN

ATSAM4S16BA-AN - 120MHz Cortex-M4, 1MB Flash MCU | Microchip

The Microchip Technology ATSAM4S16BA-AN is a 32-bit ARM Cortex-M4 microcontroller running at up to 120 MHz with 1 MB of dual-bank embedded Flash, 128 KB of SRAM, and 47 GPIO, packaged in a 64-pin LQFP (10 x 10 mm) surface-mount package. A microcontroller (MCU) is a single-chip computer integrating a processor core, program memory, data memory, and peripherals into one package, sitting at the device level of the embedded-systems hierarchy below system-on-chip and above discrete logic. The SAM4S family belongs to Microchip's ARM-based SAM portfolio, using the 32-bit ARM Cortex-M4 RISC processor with DSP instructions and a Thumb-2 instruction set, plus a Memory Protection Unit (MPU) for robust software partitioning. Key features include a 1.62 V to 3.6 V operating supply, 1 MB of ECC-protected dual-bank Flash with Security Bit and lock regions, and rich connectivity: I2C, SPI, UART/USART, SSC (I2S), IrDA, memory-card interfaces, and USB. Peripheral set covers DMA, PWM, watchdog timer, brown-out detect/reset, and power-on reset, enabling compact single-chip designs. Architecture highlights include the Cortex-M4 DSP extension set for single-cycle MAC operations, fast Flash with prefetch for zero-wait-state execution at lower frequencies, and efficient power consumption of roughly 200 uA/MHz as published on the Microchip SAM4S16 product page. The dual-bank Flash architecture supports safe in-application programming and firmware update schemes. Typical applications include industrial control and automation nodes, consumer and portable devices, motor control with PWM peripherals, and USB-connected instrumentation. The 47 I/O count and 64-LQFP footprint suit compact, moderately pin-count-limited boards. Design consideration: keep decoupling capacitors close to all VDD/VDDIO pins and respect the 1.62 V to 3.6 V I/O range; the plastic LQFP 10 x 10 body needs no heatsink but benefits from solid ground pours. This page adds value beyond the manufacturer datasheet by synthesizing distributor pricing tiers, verified drop-in alternatives, and practical design notes in one place.

RFQ تماس
ATSAM4S16BA-AU - 120MHz Cortex-M4 MCU | Microchip
ATSAM4S16BA-AU

ATSAM4S16BA-AU - 120MHz Cortex-M4 MCU | Microchip

Microchip Technology ATSAM4S16BA-AU is a 32-bit ARM Cortex-M4 microcontroller operating up to 120 MHz, with 1 MB of dual-bank embedded Flash, 128 KB of SRAM, and a 64-LQFP 10 mm × 10 mm package. The device belongs to the SAM4S family of embedded microcontrollers and combines a high-performance processor core with extensive programmable peripherals for control-oriented embedded systems. An ARM Cortex-M4 microcontroller is a 32-bit reduced-instruction-set processor designed for embedded control, and the ATSAM4S16BA-AU adds Flash memory, SRAM, clock management, communication peripherals, and GPIO around that core. Its 2 KB cache improves instruction-fetch performance, while the Memory Protection Unit, DSP instruction set, and Thumb-2 instruction set support efficient real-time and signal-processing workloads. This places the device in the hierarchy of Cortex-M processor, embedded microcontroller, semiconductor, and programmable control system. Key features include a maximum operating frequency of 120 MHz, 1 MB of Flash organized as 1M × 8 bits, 128 KB of SRAM, and a 1.62 V to 3.6 V operating-supply range. The dual-bank Flash includes ECC, a security bit, and lock features. The integrated DSP instruction set accelerates common arithmetic operations, while the 2 KB cache supports higher instruction throughput from embedded Flash. The SAM4S architecture provides a Memory Protection Unit for isolating memory regions, supporting both performance and software reliability. Its pin compatibility with the SAM3N, SAM3S, SAM4N, and 64-pin SAM7S families simplifies migration within the Microchip portfolio. The 64-LQFP package exposes a substantial pin count for general-purpose I/O and peripheral connections while remaining compatible with surface-mount manufacturing and inspection processes. Typical applications include industrial control panels, sensor-hub and condition-monitoring equipment, building automation controllers, data-acquisition systems, embedded gateways, and industrial communication equipment. The combination of 120 MHz processing, 1 MB Flash, and 128 KB SRAM supports moderate real-time workloads, protocol stacks, local data buffering, and control logic without an external memory interface. Designers should verify the exact peripheral map, pin multiplexing, clock limits, and operating-temperature grade against the manufacturer datasheet before schematic release. The 1.62 V minimum supply and 3.6 V maximum supply define the operating range, while correct decoupling, clock configuration, programming access, and unused-pin handling are essential for reliable operation. This product page combines the manufacturer-family specifications, package and memory details, lifecycle information, drop-in alternatives, comparison parameters, and practical design guidance into one engineering-focused reference for selecting and implementing the ATSAM4S16BA-AU.

RFQ تماس
ATSAM4S16BA-MU - 120MHz Cortex-M4 MCU 1MB Flash | Microchip
ATSAM4S16BA-MU

ATSAM4S16BA-MU - 120MHz Cortex-M4 MCU 1MB Flash | Microchip

The Microchip Technology ATSAM4S16BA-MU is a 32-bit ARM Cortex-M4 flash microcontroller running at up to 120 MHz, with 1 MB of dual-bank embedded Flash with ECC and 128 KB of SRAM, housed in a 64-pin QFN (9x9 mm) surface-mount package. It operates from a single 1.62V to 3.6V supply and achieves approximately 200 uA/MHz active power consumption. A flash microcontroller (MCU) integrates a processor core, program memory, data memory, and peripherals on a single die, forming the complete control engine of an embedded system. Within the power management hierarchy of embedded design, an MCU sits above discrete logic and below application processors: it executes deterministic real-time control loops, manages communication peripherals, and handles signal processing workloads such as those enabled by the Cortex-M4 DSP instruction set. Key differentiating features of the ATSAM4S16BA-MU include a 2 Kbytes instruction cache that sustains near-zero-wait-state execution from Flash at 120 MHz, a Memory Protection Unit (MPU) for robust task isolation, a DSP instruction set with Thumb-2 encoding for efficient signal processing, and dual-bank Flash with ECC, Security Bit, and lock regions enabling safe in-application firmware updates. The multi-layer bus matrix and multi-channel DMA support high data-rate communication without CPU bottlenecking. Architecturally, the device is built on the high-performance ARM Cortex-M4 core and integrates Atmel/Microchip Flash read accelerator technology. The dual-bank memory organization allows one bank to execute code while the other is erased or programmed, a critical capability for field-upgradable industrial products that cannot tolerate downtime. ECC on Flash protects against single-bit errors in noisy environments. Typical applications include industrial control and automation nodes, consumer appliances, PC peripherals, and portable data-acquisition instruments. The 200 uA/MHz efficiency and wide 1.62V to 3.6V supply range also suit battery-powered designs that still need DSP-grade throughput. When designing with this MCU, budget the power architecture around the 1.62V to 3.6V supply window and exploit the pin-to-pin compatibility with SAM3N/SAM3S/SAM4N/SAM7S (64- and 100-pin versions) to simplify migration; verify USB and peripheral count differences before swapping families. This page synthesizes distributor pricing, drop-in alternatives within the SAM4S family, and practical design notes not found in the manufacturer datasheet, as of 2026-09-20.

RFQ تماس
ATSAM4S16BA-UUR - 120MHz Cortex-M4 MCU 1MB Flash | Microchip
ATSAM4S16BA-UUR

ATSAM4S16BA-UUR - 120MHz Cortex-M4 MCU 1MB Flash | Microchip

The Microchip ATSAM4S16BA-UUR is a 32-bit ARM Cortex-M4 microcontroller running at up to 120 MHz, with 1 MB dual-bank embedded Flash, 128 KB SRAM, and a compact 64-ball WLCSP package measuring 4.42 x 3.42 mm. A microcontroller (MCU) integrates a processor core, memory, and peripherals on a single chip, forming the compute backbone of embedded systems within the wider hierarchy of semiconductor devices (MCU -> processor -> integrated circuit -> semiconductor). The SAM4S family, based on the ARM Cortex-M4 RISC core, adds a Memory Protection Unit (MPU), DSP instructions, and the Thumb-2 instruction set, making it a mid-range workhorse between simpler Cortex-M0+ parts and higher-end Cortex-M7 devices. Key features include the 120 MHz Cortex-M4 core with hardware DSP support, 1024 KB dual-bank Flash with ECC, Security Bit and lock functionality, and a multi-layer bus matrix with multi-channel DMA for high data-rate communication. Atmel's Flash read accelerator with optional cache memory boosts effective execution speed, while power consumption is approximately 200 uA/MHz, and supply operation spans 1.62 V to 3.6 V for battery-friendly designs. Technically, the dual-bank Flash architecture enables safe in-application firmware updates (bank swap without an external bootloader), while ECC protects against single-bit Flash errors. The MPU supports functional-safety and RTOS memory partitioning. The SAM4S series is pin-to-pin and software compatible with SAM3N, SAM3S, SAM4N, and SAM7S legacy series in matching pin counts, providing a smooth migration path from Cortex-M3 designs. Typical applications include industrial control and automation nodes, portable and wearable devices where the 4.42 x 3.42 mm WLCSP footprint saves board space, and IoT sensor endpoints requiring DSP capability for signal processing. The industrial temperature rating supports harsh environments. Design consideration: WLCSP packages require precise PCB land-pattern design and reflow control; a via-in-pad or fanout strategy is needed to route 64 balls on two or more signal layers. Verify Flash wait-state settings at 120 MHz per the SAM4S family datasheet (document 60001419). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, combining verified web data from Mouser, DigiKey, LCSC, and Octopart as of 2026-09-20.

RFQ تماس
ATSAM4S16BB-AN - 120MHz Cortex-M4 MCU 1MB Flash | Microchip (Tape & Reel)
ATSAM4S16BB-AN

ATSAM4S16BB-AN - 120MHz Cortex-M4 MCU 1MB Flash | Microchip (Tape & Reel)

The Microchip Technology ATSAM4S16BB-AN is a 32-bit ARM Cortex-M4 flash microcontroller in the SAM4S series, operating at up to 120 MHz with 1 MB (1M x 8) of embedded Flash and housed in a 64-pin LQFP (10 x 10 mm) surface-mount package. A microcontroller unit (MCU) integrates a processor core, program memory, data memory, and peripherals on a single chip, sitting at the heart of embedded systems as the central element of the power-management and control hierarchy. The ARM Cortex-M4 architecture targets mid-range embedded control, combining 32-bit processing performance with deterministic real-time behavior and low interrupt latency. Key features of the ATSAM4S16BB-AN include the high-performance Cortex-M4 RISC core at 120 MHz, 1 MB of embedded Flash with optional dual-bank implementation and cache memory, and very low power consumption of approximately 200 uA/MHz as stated on the Microchip product page. The supply range of 1.62 V to 3.6 V supports both 1.8 V and 3.3 V systems, and the peripheral set includes a full-speed USB Device port per the SAM4S family datasheet. The SAM4S series architecture adds a hardware integer multiplier-accumulator (MAC), optional floating-point-style DSP instructions from the Cortex-M4 core, and an embedded 16 KB ROM containing boot loader routines (UART, USB) and IAP (In-Application Programming) routines, simplifying field firmware updates without external programming hardware. Typical applications include industrial automation and control nodes, consumer appliances, and USB-connected embedded devices, where the combination of 1 MB Flash, 120 MHz throughput, and a USB Device port covers data logging, HMI, and bridging roles. The 64-pin LQFP makes it a natural upgrade or consolidation path within legacy boards. A key design consideration: the ATSAM4S16BB-AN is pin-to-pin compatible with the SAM3N, SAM3S, SAM4N, and SAM7S legacy series in the 64-pin version, allowing designers to migrate older designs with a footprint-preserving swap, though software must be recompiled for the Cortex-M4. This page synthesizes distributor pricing, drop-in alternatives within the SAM4S family, and practical design notes not found in the manufacturer datasheet alone.

RFQ تماس
ATSAM4S16BB-ANR - 120MHz Cortex-M4 MCU 1MB Flash | Microchip
ATSAM4S16BB-ANR

ATSAM4S16BB-ANR - 120MHz Cortex-M4 MCU 1MB Flash | Microchip

The Microchip Technology ATSAM4S16BB-ANR is a 32-bit ARM Cortex-M4 flash microcontroller in the SAM4S series, operating at up to 120 MHz with 1 MB (1M x 8) of embedded Flash and housed in a 64-pin LQFP (10 x 10 mm) surface-mount package. A microcontroller unit (MCU) integrates a processor core, program memory, data memory, and peripherals on a single chip, sitting at the heart of embedded systems as the central element of the power-management and control hierarchy. The ARM Cortex-M4 architecture targets mid-range embedded control, combining 32-bit processing performance with deterministic real-time behavior and low interrupt latency. Key features of the ATSAM4S16BB-ANR include the high-performance Cortex-M4 RISC core at 120 MHz, 1 MB of embedded Flash with optional dual-bank implementation and cache memory, and very low power consumption of approximately 200 uA/MHz as stated on the Microchip product page. The supply range of 1.62 V to 3.6 V supports both 1.8 V and 3.3 V systems, and the peripheral set includes a full-speed USB Device port per the SAM4S family datasheet. The SAM4S series architecture adds a hardware integer multiplier-accumulator (MAC), optional floating-point-style DSP instructions from the Cortex-M4 core, and an embedded 16 KB ROM containing boot loader routines (UART, USB) and IAP (In-Application Programming) routines, simplifying field firmware updates without external programming hardware. Typical applications include industrial automation and control nodes, consumer appliances, and USB-connected embedded devices, where the combination of 1 MB Flash, 120 MHz throughput, and a USB Device port covers data logging, HMI, and bridging roles. The 64-pin LQFP makes it a natural upgrade or consolidation path within legacy boards. A key design consideration: the ATSAM4S16BB-ANR is pin-to-pin compatible with the SAM3N, SAM3S, SAM4N, and SAM7S legacy series in the 64-pin version, allowing designers to migrate older designs with a footprint-preserving swap, though software must be recompiled for the Cortex-M4. This page synthesizes distributor pricing, drop-in alternatives within the SAM4S family, and practical design notes not found in the manufacturer datasheet alone.

RFQ تماس
ATSAM4S16CA-AN - Cortex-M4 120MHz 1MB Flash MCU | Microchip
ATSAM4S16CA-AN

ATSAM4S16CA-AN - Cortex-M4 120MHz 1MB Flash MCU | Microchip

The Microchip Technology ATSAM4S16CA-AN is a 32-bit ARM Cortex-M4 microcontroller running at up to 120 MHz, with 1024 Kbytes dual-bank embedded Flash and 128 Kbytes SRAM, housed in a 100-pin LQFP Green (AN) package. A microcontroller (MCU) integrates a processor core, memory, and peripherals onto a single chip, sitting at the device level of the embedded-systems hierarchy between discrete logic and full application processors. The SAM4S series belongs to the ARM Cortex-M4 family of 32-bit microcontrollers, which combine general-purpose MCU control capability with DSP instructions and Thumb-2 technology for efficient signal processing. Key features include the Cortex-M4 core with a Memory Protection Unit (MPU), DSP instruction support, dual-bank Flash with ECC, Security Bit and Flash lock protection, plus rich connectivity: EBI/EMI external bus, I2C, IrDA, memory card interface, SPI, SSC, UART/USART, and USB. Peripheral support covers brown-out detect/reset, DMA, POR, PWM, and a watchdog timer, with 79 general-purpose I/O lines. The dual-bank Flash architecture enables safe in-field firmware updates: the device can execute from one bank while erasing or programming the other, reducing boot-loader downtime risk. ECC on Flash improves reliability in electrically noisy industrial environments. The SAM4S series operates from 1.62V to 3.6V and is pin-to-pin compatible with the SAM7S, SAM3N, SAM3S, and SAM4N families, providing a clear migration path from legacy designs. Typical applications include industrial control, consumer products, and PC peripherals, as well as USB-equipped field devices, motor-control systems using PWM outputs, and data-acquisition nodes using the SSC and memory card interfaces. Design considerations: operate within the 1.62V to 3.6V supply range, budget the 79 available I/O against the EBI external memory bus requirements, and plan the dual-bank Flash layout early to take full advantage of ECC and safe update capability. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with data verified as of 2026-09-20.

RFQ تماس
ATSAM4S16CA-ANR - Cortex-M4 MCU 120MHz 1MB Flash | Microchip
ATSAM4S16CA-ANR

ATSAM4S16CA-ANR - Cortex-M4 MCU 120MHz 1MB Flash | Microchip

The Microchip Technology ATSAM4S16CA-ANR is a 32-bit ARM Cortex-M4 microcontroller with a maximum operating frequency of 120 MHz, 1 MB (1024 KB) dual-bank embedded Flash with ECC, and 128 KB of SRAM, housed in a 100-pin LQFP (14x14 mm) package. A microcontroller (MCU) is a single-chip embedded computer that integrates a processor core, program memory, data memory, and peripherals on one die. Within the power-management hierarchy of embedded systems, general-purpose MCUs like the SAM4S family form the central control layer, executing application firmware while driving communication, sensing, and actuation peripherals. Key features include the Cortex-M4 core with DSP instructions and Thumb-2 instruction set, a Memory Protection Unit (MPU), dual-bank Flash supporting safe in-application programming, and a Security Bit plus Flash lock for IP protection. According to Microchip, power consumption is 200 uA/MHz, and the supply range of 1.62V to 3.6V enables battery and 3.3V industrial designs. The SAM4S16 architecture pairs the Cortex-M4 with a multi-layer bus matrix, DMA-capable peripherals such as UART, USART, SPI, I2C/TWI, and a 12-bit ADC, sustaining deterministic real-time behavior for control loops while DSP instructions accelerate filtering and math-intensive routines. The parallel input/output (PIO) data-capture mode supports high-throughput digital acquisition. Typical applications include industrial automation controllers, smart energy metering, portable/battery-powered devices, and consumer/POS equipment, where the combination of 120 MHz performance, low power, and rich connectivity fits cost-sensitive designs. Design consideration: the SAM4S series is pin-to-pin compatible with SAM3N, SAM3S, SAM4N, and legacy SAM7S (64-pin versions), so layouts can be upgraded without PCB rework; validate VDDIO levels when migrating from 5V-tolerant legacy parts. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ تماس
ATSAM4S16CA-AU - Cortex-M4 120MHz 1MB Flash MCU | Microchip
ATSAM4S16CA-AU

ATSAM4S16CA-AU - Cortex-M4 120MHz 1MB Flash MCU | Microchip

The Microchip Technology ATSAM4S16CA-AU is a 32-bit ARM Cortex-M4 flash microcontroller running at up to 120 MHz, with 1 MB (1024 KB) of embedded flash memory and 128 KB of SRAM, housed in a 100-pin LQFP (14 x 14 mm) surface-mount package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, program memory, data memory, and a rich set of peripherals into one chip, forming the brain of an embedded system. The ATSAM4S16CA-AU belongs to the SAM4S family within the broader hierarchy of ARM-based flash MCUs: Cortex-M4 core -> 32-bit RISC microcontroller -> SAM4S series -> Microchip (formerly Atmel) AT91/SAM portfolio. Key features include an ARM Cortex-M4 core with a 2 Kbyte cache and Memory Protection Unit (MPU), a hardware DSP instruction set, and the Thumb-2 instruction set for high code density. The 120 MHz operating frequency combined with DSP instructions makes it significantly faster than the Cortex-M3-based SAM3S parts it can replace. Peripherals cover EBI/EMI external bus, I2C (TWI), IrDA, MMC/SD, SPI, SSC, and UART/USART serial connectivity, enabling flexible interfacing to displays, sensors, and storage. A major engineering advantage is pin-to-pin compatibility with the SAM4N, SAM3S, SAM3N (48-, 64- and 100-pin versions) and legacy SAM7S (64-pin) families, allowing designers to migrate designs or respond to shortages without PCB respins. The 1.2 V/3.3 V supply options and industrial temperature range suit harsh environments. Typical applications include industrial control and automation, consumer products with human-machine interfaces, metering systems, and IoT sensor nodes that benefit from DSP capability and large 1 MB flash for complex firmware. When designing, plan flash bank usage and take advantage of the parallel input/output (PIO) data capture mode for high-speed data acquisition tasks. This page synthesizes distributor availability data, family cross-references, and practical migration guidance not found in the manufacturer datasheet alone.

RFQ تماس
ATSAM4S16CA-AUR - 120MHz Cortex-M4 MCU 1MB Flash | Microchip
ATSAM4S16CA-AUR

ATSAM4S16CA-AUR - 120MHz Cortex-M4 MCU 1MB Flash | Microchip

The Microchip Technology ATSAM4S16CA-AUR is a 32-bit ARM Cortex-M4 flash microcontroller running at up to 120 MHz with 1 MB of embedded flash and 128 KB of SRAM, housed in a 100-pin LQFP (14x14 mm) surface-mount package supplied on tape and reel. A microcontroller unit (MCU) is a single-chip computer that integrates a processor core, memory, and peripherals onto one die, sitting at the lowest level of the embedded-system hierarchy above discrete logic but below application processors. The SAM4S family belongs to Microchip's (formerly Atmel's) SMART ARM-based MCU portfolio and offers pin-to-pin compatibility with SAM4N, SAM3S, SAM3N, and SAM7S devices, enabling easy migration within the portfolio. Key features of the ATSAM4S16CA-AUR include the high-performance Cortex-M4 RISC core with DSP extensions and single-cycle multiply-accumulate, 120 MHz maximum core speed, 1 MB (1M x 8) of flash program memory, and operation from 1.2 V, 1.8 V, 2.5 V, or 3.3 V supply rails. The device integrates fast Flash memory with dual instruction/data access paths, multiple serial communication peripherals, and rich analog and timer resources typical of the SAM4S family. Technically, the SAM4S series implements the ARMv7E-M architecture with hardware FPU-class DSP instructions, multi-layer bus matrix for parallel peripheral access, and a parallel input/output (PIO) data-capture mode. This architecture sustains deterministic real-time behavior at high clock rates while keeping interrupt latency low, making the part well-suited to control-loop intensive designs that also perform digital signal processing. Typical applications include industrial automation and motor control, consumer and portable devices, PC peripherals, and networking or connectivity nodes. The combination of 1 MB flash and 120 MHz throughput supports protocol stacks, graphics-lite HMI, and digital filtering without an external processor. A key design consideration is supply-rail selection: the device supports multiple voltage operating points, so confirm the required 1.2 V/1.8 V/2.5 V/3.3 V domain configuration against the SAM4S datasheet early in the power-tree design, and verify the industrial temperature range (-40C to +85C) of the AUR suffix against your environmental requirements. This page synthesizes distributor pricing, drop-in alternatives within the same 100-LQFP footprint, and practical design notes not found in the manufacturer datasheet.

RFQ تماس
ATSAM4S16CA-CFN - 120MHz Cortex-M4 1MB Flash MCU | Microchip
ATSAM4S16CA-CFN

ATSAM4S16CA-CFN - 120MHz Cortex-M4 1MB Flash MCU | Microchip

The Microchip Technology ATSAM4S16CA-CFN is a 32-bit ARM Cortex-M4 flash microcontroller running at up to 120 MHz with 1024 Kbytes of dual-bank embedded Flash and a 100-ball VFBGA (GREEN, EXT) package. A 32-bit microcontroller (MCU) is a single-chip computing device that integrates a processor core, memory, and peripherals on one die, forming the lowest layer of the embedded-system hierarchy (microcontroller -> embedded processor -> system-on-chip -> semiconductor device). The SAM4S family belongs to Microchip's (formerly Atmel) ARM-based SAM portfolio and executes the Thumb-2 instruction set with DSP instructions and a Memory Protection Unit (MPU), positioning it between entry-level Cortex-M0+/M3 parts and high-performance Cortex-M7 devices. Key features include the 120 MHz Cortex-M4 core with hardware MAC and DSP instructions, 1024 KB dual-bank Flash with ECC, Security Bit and lock bits, and pin-to-pin compatibility with the legacy SAM7S, SAM3N and SAM3S series in the 100-pin footprint. Parallel Input/Output (PIO) data capture mode and a full-speed USB Device port round out the peripheral set. Architecturally, the dual-bank Flash implementation enables safe in-application programming and firmware updates, while the ECC protects stored code against bit corruption. The ARM Cortex-M4 pipeline with single-cycle MAC accelerates digital signal processing such as filtering and FFT-based algorithms common in industrial control. Typical applications include industrial automation control nodes, consumer and industrial HMI/USB peripherals, and data-acquisition systems that leverage the PIO capture mode and DSP capability. Design consideration: the VFBGA package demands controlled-impedance PCB layout and proper ball-map fan-out planning; verify power-domain sequencing per the manufacturer datasheet before first power-up. This page synthesizes distributor pricing from seven sources, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ تماس