محصولات (21,000+)

Z86E2116VSC - 8-Bit 16MHz OTP MCU with UART | Zilog
Z86E2116VSC

Z86E2116VSC - 8-Bit 16MHz OTP MCU with UART | Zilog

The Zilog Z86E2116VSC is an 8-bit Z8 CMOS microcontroller with a 16 MHz operating frequency, 8 KB of one-time-programmable memory, and UART capability in a 44-lead PLCC package. It combines an embedded 8-bit processor, 8K × 8 OTP program memory, and serial communications in a single integrated circuit designed for compact embedded control, appliance control, and simple communications equipment. An 8-bit microcontroller is a microprocessor integrated with memory, I/O, timers, and peripheral functions on one semiconductor die. The Z8 family belongs to the broader embedded-controller hierarchy: microcontroller, embedded processor, semiconductor, and electronic component. One-time-programmable memory is intended for production firmware that does not need revision after programming, allowing the finished controller to provide compact, dedicated control without external program-memory devices. The principal characteristics of the Z86E2116VSC include a maximum 16 MHz clock, 8 KB of OTP program memory organized as 8K × 8, an 8-bit data bus, and integrated UART communication. Its 44-lead PLCC package provides a surface-mount option for industrial and consumer assemblies. Because the programming technology is OTP rather than flash, firmware changes after manufacture generally require a new programmed device. The Z86E2116VSC uses Zilog's Z8 architecture, an 8-bit CMOS platform intended for cost-sensitive embedded products. Its relatively high 16 MHz clock supports time-sensitive control loops, while the dedicated UART supports serial communication with sensors, human-interface equipment, data converters, or other embedded controllers. The 8 KB code space is best suited to compact applications in which the firmware can fit within one program-memory block. Typical uses include appliance and appliance-control panels, simple serial interfaces, instrumentation, industrial modules, and compact consumer products. The UART makes the device appropriate for point-to-point supervisory communication, while the integrated OTP program memory is useful for dedicated firmware where field updates are unnecessary. System designers should also consider oscillator startup behavior, I/O drive requirements, and programming provisions before finalizing a PCB. A critical design consideration is the distinction between a drop-in replacement and a merely similar MCU. Pin compatibility, clocking, memory capacity, peripheral availability, interrupt behavior, and package dimensions must all be checked before substituting another device. The manufacturer datasheet pin table and device programming information should be used as the authority for PCB and firmware decisions. This product page consolidates the confirmed Z86E2116VSC specifications, package information, UART and OTP details, sourcing information, comparison dimensions, and practical design guidance into one engineering-oriented reference. It is intended to help designers determine whether this Z8 MCU fits the required memory, timing, package, and communication architecture before requesting a quotation.

RFQ تماس
Z86E2204PSC - 8-Bit 8KB OTP CMOS Microcontroller | Zilog
Z86E2204PSC

Z86E2204PSC - 8-Bit 8KB OTP CMOS Microcontroller | Zilog

The Zilog, Inc. Z86E2204PSC is an 8-bit CMOS Z8 OTP microcontroller with 8 KB of one-time-programmable program memory in a 40-pin DIP package. It is designed for embedded control applications requiring compact logic integration, user-programmable nonvolatile storage, and a conventional through-hole footprint. An 8-bit microcontroller is a microprocessor optimized for embedded control rather than general-purpose computing. The Z8 OTP family combines a CPU core, programmable memory, digital I/O, timers, and communication resources on one integrated circuit. Because the program memory is one-time-programmable, the configured instruction sequence cannot normally be changed after programming, making the device suitable for dedicated products whose firmware is finalized during manufacturing. The Z86E2204PSC provides 8 KB of OTP program memory and operates as a CMOS microcontroller. Its 40-pin DIP package supports prototyping, repair, and applications where through-hole assembly is preferred over a compact surface-mount package. The device is listed as obsolete, so new designs should confirm lifecycle status and consider a supported MCU unless an existing product requires the exact function and footprint. The principal engineering consideration is the OTP programming model. Firmware must be validated before the device is programmed because later field changes are impossible. Designers should also assign every physical pin according to the manufacturer pin-description table, verify the programming interface, and ensure that unused inputs cannot float. Logic levels, oscillator requirements, and peripheral resources must be checked against the exact datasheet before schematic capture. Typical uses include appliance controllers, simple sequencers, dedicated interface modules, and legacy industrial equipment where a compact 8-bit control engine is sufficient. The MCU can also serve as a supervisory controller when its I/O count and embedded resources meet the product requirements. Since the part is obsolete and described as an 8 KB OTP device, it is most appropriate for maintenance, continuation, or exact-fit replication rather than new platform development without a qualified alternative. When laying out a board, preserve the 40-pin DIP footprint, provide adequate clearance for programming and soldering, and decouple supply pins near the device according to the manufacturer application guidance. Confirm startup behavior, oscillator limits, and I/O levels in hardware. For new designs, use the Request a Quote form on this page to ask about exact-fit availability and engineering support. This page consolidates lifecycle information, package details, programming constraints, application guidance, and verification steps for engineers maintaining legacy Z8-based equipment. It also highlights the practical difference between an exact legacy replacement and a modern MCU redesign.

RFQ تماس
Z86E2304PSC - 8-Bit 4MHz OTP Keyboard MCU | Zilog
Z86E2304PSC

Z86E2304PSC - 8-Bit 4MHz OTP Keyboard MCU | Zilog

The Zilog Z86E2304PSC is an 8-bit Z8 keyboard-controller microcontroller with 8 KB of one-time-programmable memory, a 4 MHz operating frequency, and a 40-pin through-hole DIP package. It is designed for keyboard scanning, matrix-key decoding, and embedded human-interface applications. A keyboard-controller microcontroller is an embedded MCU optimized for scanning switch matrices and managing key events. The Z86E23 family combines an 8-bit processor core, OTP program storage, RAM, timers, and keyboard-control peripherals in one device. This places it in the broader hierarchy of embedded controller, 8-bit microcontroller, and semiconductor product categories. The Z86E2304PSC provides 8 KB of OTP program memory, 236 bytes of RAM, two programmable counter/timer blocks, and a 4 MHz clock. Its pin-compatible OTP architecture is based on the Z8614 and Z8602 keyboard-controller family, allowing designers to retain established keyboard layouts while using one-time-programmable devices for production control. The controller is intended for matrix keyboard implementations where firmware must detect pressed and released keys, debounce contacts, maintain rollover information, and report key events to a host or application processor. Its dedicated keyboard-control resources reduce the amount of external logic required in simple keyboard products. Typical uses include computer keyboards, security-keypads, industrial control panels, access terminals, point-of-sale equipment, and remote key-entry modules. The 40-pin DIP package also supports prototype boards, educational platforms, and legacy control systems where through-hole assembly and socketed parts are preferred. When laying out a board, preserve the Z8 keyboard-controller signal assignments and provide adequate decoupling close to the supply pins. Confirm the external clock, reset, matrix-scan, and host-interface connections against the manufacturer datasheet before fabricating a replacement PCB. This product page combines device specifications, package details, sourcing guidance, verified drop-in candidates, and practical keyboard-controller design notes to support component selection, PCB reuse, firmware planning, and production procurement.

RFQ تماس
Z86E2304VSC - 8-Bit OTP Keyboard Controller | Zilog
Z86E2304VSC

Z86E2304VSC - 8-Bit OTP Keyboard Controller | Zilog

The Zilog Z86E2304VSC is an 8-bit Z8-family keyboard controller with 4 KB of one-time-programmable memory and a 4 MHz operating frequency. It is based on the Z86E23 family, which the Zilog datasheet describes as a pin-compatible OTP version of the Z8614 and Z8602 keyboard controllers. The device is intended for keyboard scanning, matrix-key decoding, and embedded human-interface applications. A keyboard controller is an embedded microcontroller optimized for scanning a switch matrix and converting key activity into a digital report for a host processor. Unlike a general-purpose MCU, the Z86E23 architecture integrates keyboard-specific functions so firmware can focus on debouncing, key mapping, and reporting. Its two on-chip counter/timers provide selectable operating modes for timing, delay generation, and event-related functions. Key characteristics include the 8-bit Z8 CPU core, 4 KB OTP program memory, and 4 MHz clock rating identified in distributor product listings. The OTP architecture is suited to products where programmed firmware is held permanently after programming, avoiding the need for external nonvolatile program memory. Because OTP memory cannot be electrically erased and reprogrammed, a suitable programming and validation flow must be established before production programming. Typical uses include computer keyboards, keypads, control panels, and other matrix-switch products. The controller's dedicated keyboard architecture can simplify scan handling while its counter/timer resources support debounce timing, repeat-rate control, indicator handling, and periodic host communication. Firmware and peripheral assignments should be confirmed against the pin-description table in the manufacturer datasheet before schematic capture. For new designs, verify supply continuity and programming method early because the Z8 OTP family is an established embedded-controller architecture. Confirm the exact lead count, pin assignments, operating-voltage limits, and programming connector requirements for the Z86E2304VSC rather than assuming that another Z86E-series controller has an identical peripheral map. This page organizes the documented Z86E2304VSC identity, memory and timing specifications, alternative Zilog variants, application guidance, and engineering considerations into a single design reference. Use the manufacturer datasheet as the authority for electrical limits, timing, programming, and final pin assignment.

RFQ تماس
Z86E3016PEC - 8-Bit 16MHz OTP MCU in 28-DIP | Zilog
Z86E3016PEC

Z86E3016PEC - 8-Bit 16MHz OTP MCU in 28-DIP | Zilog

The Zilog Z86E3016PEC is an 8-bit Z8 microcontroller operating at 16 MHz with 4 KB of one-time-programmable memory, 237 bytes of RAM, and 24 I/O pins in a 28-pin DIP package. Its 4.5 V to 5.5 V operating range and integrated UART make it suitable for compact embedded control systems that need deterministic peripheral integration without external program memory. An 8-bit microcontroller is a programmable semiconductor that executes firmware on a central processing unit and connects directly to sensors, switches, indicators, and communication equipment. The Z8 belongs to the broader microcontroller hierarchy, which sits within embedded processors and semiconductor control components. This Z86E3016PEC variant combines a 16 MHz operating clock, 4 KB OTP program storage, two 8-bit timers, and UART communication in one device. The principal features are a 16 MHz clock, 4 KB of OTP program memory, 237 bytes of data RAM, and 24 general-purpose I/O lines. The two 8-bit timers support periodic timing, counting, and basic event-generation tasks, while the UART provides a simple serial interface for connecting the controller to a host computer, sensor module, or another embedded controller. The Z8 architecture is designed for compact, cost-sensitive embedded control rather than high-throughput processing. Its 8-bit ALU naturally handles control states, switch logic, counters, and byte-oriented protocols efficiently. Program storage is implemented as OTP, so each device can be programmed once during manufacturing or provisioning. The 237-byte RAM provides working memory for variables, stack operations, and short-lived data structures. Typical applications include appliance controllers, small motor-control boards, instrumentation front ends, programmable logic controllers, LED-sequencing systems, and serial-interface modules. The 28-pin DIP package is useful for prototypes, educational platforms, and through-hole assemblies where reworkability and straightforward socket or PCB insertion are priorities. Designers should preserve adequate input and output voltage headroom around the 4.5 V to 5.5 V operating range. Because program memory is OTP, firmware changes after programming are not possible; validate the complete application image and test logic before production programming. The manufacturer pin-description table should also be used directly when assigning connector signals and PCB tracks. This product page combines the Z86E3016PEC core specifications, package information, application guidance, and qualified comparison points into a compact engineering reference. It also distinguishes directly interchangeable options from related devices whose package or architecture prevents a true drop-in replacement.

RFQ تماس
Z86E3016PEG - 8-Bit 16MHz 4KB OTP MCU | Zilog
Z86E3016PEG

Z86E3016PEG - 8-Bit 16MHz 4KB OTP MCU | Zilog

The Zilog Z86E3016PEG is an 8-bit Z8 microcontroller operating at 16 MHz with 4 KB of one-time-programmable memory in a 28-pin plastic dual-inline package. The verified product listings identify the device as the Z8 family member Z86E3016PEG and describe it as an 8-bit, 16 MHz microcontroller with 4K × 8 OTP program memory and UART capability. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals into one device. The Z8 belongs to the 8-bit microcontroller hierarchy, where each CPU cycle operates on an 8-bit data word. Such devices are used to read inputs, execute embedded control logic, and operate outputs in products where a compact controller, deterministic behavior, and modest processing requirements are more important than high computational throughput. The Z86E3016PEG's principal verified characteristics are its 16 MHz operating frequency, 8-bit CPU architecture, 4 KB OTP memory, and 28-pin PDIP package. The Mouser listing characterizes the device as an 8-bit MCU with 8K OTP and UART support, while the DigiKey listing identifies 4 KB, expressed as 4K × 8. Because these distributor descriptions express the OTP organization differently, engineers should confirm the exact program-memory organization against the manufacturer datasheet before assigning firmware capacity. The Z8 architecture is suitable for embedded motor-control, appliance-control, industrial-control, and serial-interface designs where an 8-bit CPU and UART simplify the control system. OTP program memory provides a one-time programmable implementation medium for products whose firmware is finalized before deployment. A 28-pin PDIP package also supports conventional through-hole assembly, prototyping, and manual inspection rather than requiring a fine-pitch surface-mount process. Before finalizing a design, verify the device's exact pin assignments, electrical limits, oscillator options, I/O count, UART characteristics, current consumption, and timing requirements using the manufacturer datasheet. Those parameters are not fully present in the supplied distributor snippets and are therefore marked as needed rather than estimated. Confirm that the 16 MHz clock source and UART baud-rate requirements can be met by the selected oscillator and external support components. This page combines verified distributor specifications, package information, pricing evidence, and explicitly qualified replacement analysis for the Z86E3016PEG. It also distinguishes verified drop-in candidates from unsupported cross-package options, helping engineers evaluate procurement and redesign decisions without treating package similarity as proof of functional equivalence.

RFQ تماس
Z86E3016PSC - 8-Bit 16MHz 4KB OTP Microcontroller | Zilog
Z86E3016PSC

Z86E3016PSC - 8-Bit 16MHz 4KB OTP Microcontroller | Zilog

The Zilog Z86E3016PSC is an 8-bit Z8 microcontroller operating at 16 MHz with 4 KB of one-time-programmable memory organized as 4K × 8 bits. The device is intended for compact embedded-control tasks that require deterministic peripheral control, low-cost programming, and a compact microcontroller architecture. Its 4 KB OTP program memory suits products whose firmware is finalized during manufacturing and does not require field reprogramming. A microcontroller is a semiconductor integrated circuit that combines a CPU core, program memory, data memory, and peripherals on one device. The Z8 belongs to the microcontroller hierarchy, where it sits between a general-purpose processor and dedicated logic. Unlike a fixed-function controller, the Z86E3016PSC can implement application-specific behavior through firmware while keeping the external component count and board area comparatively low. The principal published specifications identify an 8-bit architecture, a 16 MHz operating frequency, and 4 KB of OTP program memory. These three parameters establish the part’s fundamental design class: a compact, moderately clocked MCU for embedded-control logic rather than a high-compute application processor. Program storage is sufficient for production firmware containing control routines, state machines, communication handling, and peripheral coordination when the application does not require downloadable updates. The Z8 architecture is positioned as an efficient embedded-control platform. Its 8-bit processing model and moderate clock rate can provide adequate responsiveness for motor, appliance, instrument, and interface-control duties while keeping power, timing, and memory requirements manageable. Exact timer, I/O, serial-interface, voltage, temperature, and electrical-limit details must be confirmed against the manufacturer datasheet before a schematic or firmware is released. Typical use cases include small appliance controls, compact sensor interfaces, simple motor-control boards, keyboard or panel logic, and dedicated control subsystems. The 16 MHz clock provides a practical timing base for many event-driven control loops, while 4 KB of OTP firmware storage can be efficient for stable, fixed-function products. For connected or highly regulated products, verify the available communications peripherals and compliance requirements against the applicable product documentation. The key design consideration is OTP suitability. One-time-programmable memory is appropriate when firmware is finalized before deployment and field updates are unnecessary; it is not the natural choice for products requiring frequent firmware updates or field-service reconfiguration. Confirm the exact package, pin count, pinout, electrical ratings, and programming procedure from the Zilog datasheet before laying out the PCB or ordering samples. This page consolidates the confirmed Z86E3016PSC specifications, sourcing information, application guidance, and replacement analysis into an engineering-focused product record. It also separates verified core attributes from details that require datasheet confirmation, helping designers establish whether the Z8 MCU fits the architecture before beginning detailed schematic work.

RFQ تماس
Z86E3016PSG - 8-Bit 16MHz OTP MCU | Zilog
Z86E3016PSG

Z86E3016PSG - 8-Bit 16MHz OTP MCU | Zilog

Zilog Z86E3016PSG is an 8-bit Z8-family microcontroller with 16 MHz operating frequency, 4 KB of one-time-programmable program memory, 237 bytes of RAM, and 24 I/O pins in a 28-pin package. It is designed for cost-sensitive embedded-control applications that require simple programming, low-power wake-up behavior, and dedicated on-chip peripherals. A microcontroller is a programmable semiconductor that integrates a CPU, memory, I/O ports, timers, and support circuitry on one chip. The Z8 architecture belongs to the broader microcontroller and embedded-processor hierarchy. Compared with application-specific controllers, an OTP microcontroller offers a straightforward way to implement fixed control logic in appliances, security devices, HVAC equipment, and other compact electronic products. Verified device features include one-time-programmable memory, enhanced wake-up circuitry, programmable watchdog timers, and selectable low-noise EMI options. The 16 MHz operating speed provides processing headroom for simple digital control, while 24 I/O lines allow the device to connect to sensors, switches, indicators, and actuators. Two 8-bit timers support periodic events, timing delays, and basic event generation without requiring additional timing components. The 4 KB OTP program memory is organized as 4K by 8 bits, and the device includes 237 bytes of RAM for working data. OTP memory permits the final application firmware to be programmed once, making the controller well suited to production products whose control logic does not require field updates. This simplifies manufacturing compared with flash-programmable alternatives, but it also means a firmware revision generally requires a new programmed device rather than an in-system memory update. Typical uses include appliance controls, security-system peripherals, temperature and process-control equipment, HVAC modules, and compact industrial controllers. The 24 available I/O pins simplify designs that need multiple digital inputs and outputs, while the watchdog timer helps recover operation after faults or unexpected program flow. Enhanced wake-up circuitry supports low-power systems that must respond to external activity without maintaining continuous high activity. Designers should verify the exact package pinout, operating voltage, clock configuration, and programming procedure against the Zilog datasheet before layout. The provided search data confirms a 28-pin device but does not expose authoritative pin names or a complete manufacturer PDF URL, so those details remain marked as data needed rather than being inferred. Firmware and board design should also account for OTP programming limitations and the watchdog timeout behavior.

RFQ تماس
Z86E3016SEC - 8-Bit 16MHz OTP Microcontroller | Zilog
Z86E3016SEC

Z86E3016SEC - 8-Bit 16MHz OTP Microcontroller | Zilog

Zilog Z86E3016SEC is an 8-bit Z8 microcontroller with a 16 MHz operating frequency, 4 KB of one-time-programmable ROM, and a 28-pin small-outline integrated-circuit package. Designed for compact embedded control, the device combines a CISC processor core with on-chip program memory and operates from a 5 V supply. Its industrial temperature range extends from -40°C to 105°C, making it suitable for embedded products operating across extended ambient conditions. An 8-bit microcontroller is a compact computing device that integrates a processor core, program memory, data memory, and peripheral functions onto one integrated circuit. The Z8 family belongs to the broader embedded-controller hierarchy, where an MCU executes firmware for sensing, control, communications, and user-interface functions. Compared with a field-programmable controller, the one-time-programmable ROM in Z86E3016SEC is intended for final program loading during production, providing a simple method for controlling the programmed contents of each device. The principal operating characteristics of Z86E3016SEC include its 8-bit architecture, 16 MHz clock rating, 4 KB OTP program storage, and 5 V supply. These specifications make the device appropriate for compact controllers whose workload does not require a high-performance 16-bit or 32-bit processor. The 28-pin SOIC package provides a conventional surface-mount format suitable for automated assembly and PCB integration. The Z86E3016SEC belongs to the Zilog Z8 family of 8-bit CISC microcontrollers. Its 4 KB of OTP memory gives a production designer enough space for small embedded programs, while the 16 MHz operating rating supports responsive sequential control. Because OTP memory cannot be rewritten after programming, the device is best suited to products whose firmware and configuration are stable during manufacturing rather than applications that require frequent in-field firmware updates. Typical applications include appliance controllers, compact industrial automation modules, environmental monitoring equipment, simple serial-interface products, embedded access-control terminals, and dedicated control panels. In each case, the MCU can execute a fixed control routine while coordinating inputs, outputs, and communication tasks. The -40°C to 105°C rating broadens its suitability for equipment deployed in environments where consumer-grade components may be unsuitable. Design planning should begin with the 5 V supply requirement and the 28-pin footprint. Confirm pin assignments, oscillator requirements, programming procedure, and reset behavior against the Zilog manufacturer datasheet before layout release. Because the program memory is one-time programmable, firmware validation, programming fixtures, traceability, and production provisioning must be completed before the devices are placed into finished assemblies. This page consolidates the core Z86E3016SEC electrical and packaging characteristics, identifies documented same-footprint alternatives, and provides practical selection guidance for designers evaluating the Z8 OTP MCU for compact embedded-control products.

RFQ تماس
Z86E3016SEG - 8-Bit 16MHz OTP Microcontroller | Zilog
Z86E3016SEG

Z86E3016SEG - 8-Bit 16MHz OTP Microcontroller | Zilog

Zilog Z86E3016SEG is an 8-bit Z8 microcontroller with a 16 MHz clock, 4 KB one-time-programmable ROM, 236 bytes of RAM, and 24 I/O lines in a 28-pin SOIC package. The device operates from a 4.5 V to 5.5 V supply, targets industrial-temperature applications, and is classified by Zilog as active. An 8-bit microcontroller is a compact embedded-control IC that integrates a processor core, program memory, data memory, and digital I/O into one package. In the product hierarchy, the Z86E3016SEG belongs to the Z8 family of 8-bit microcontrollers and combines a dedicated CPU core with OTP program storage. Its 16 MHz operating speed supports straightforward control logic, while 24 I/O lines provide connections to sensors, switches, indicators, actuators, and other digital peripherals. Key features include 4 KB of OTP ROM, 236 bytes of RAM, 24 I/O lines, and a 16 MHz maximum clock. Programmable OTP options include an RC oscillator, EPROM protection, auto-latch disable, and programmable configurations. Because program memory is one-time programmable, firmware is permanently programmed during manufacturing or provisioning rather than rewritten during normal use. The Z86E3016SEG uses the Z8 8-bit architecture and is designed for dedicated embedded-control tasks rather than high-compute workloads. Its 236-byte RAM supports working variables and short-lived data structures, while the 4 KB ROM provides 4096 bytes for fixed application instructions. The 24 digital I/O lines offer substantial interface capacity for compact controllers that do not require external memory or a high-speed communications interface. Typical uses include industrial control panels, appliance controllers, simple motor-control interfaces, keypads, LED status systems, and compact embedded instruments. These applications benefit from the combination of a 16 MHz processor, 24 I/O lines, and a limited, predictable memory footprint. Designers should account for one-time programming when creating production firmware and verify the final code image before programming any sample or production device. For new layouts, route the 24 I/O signals away from sensitive analog or clock circuitry and follow the pin-description table in the manufacturer datasheet when assigning PCB functions. Confirm oscillator, reset, programming, and supply connections against the exact package drawing. Because the OTP program is not reusable, production planning should include firmware validation, programming yield controls, and traceability for each programmed device.

RFQ تماس
Z86E3016SSG - 8-Bit 16MHz OTP Microcontroller | Zilog
Z86E3016SSG

Z86E3016SSG - 8-Bit 16MHz OTP Microcontroller | Zilog

The Zilog Z86E3016SSG is an 8-bit Z8 microcontroller operating at 16 MHz with 4 KB of one-time-programmable program memory, 125 bytes of RAM, and 24 I/O lines in a 28-pin SOIC package. It operates from a 4.5 V to 5.5 V supply and is specified for a 0°C to 70°C ambient-temperature range. A microcontroller is an integrated circuit that combines a processor core, nonvolatile program memory, working RAM, and peripherals on one semiconductor device. The Z86E3016SSG belongs to the Z8 family of 8-bit microcontrollers and provides a compact control platform for products that require deterministic digital control but do not need the processing power, memory, or peripheral complexity of a 32-bit embedded processor. Its one-time-programmable architecture is intended for production devices whose firmware does not need field reprogramming. The principal device characteristics include a 16 MHz clock, 4 KB OTP program memory organized as 4K by 8 bits, 125 bytes of RAM, and 24 general-purpose I/O lines. Integrated power-on reset and watchdog-timer functions support dependable startup and recovery behavior. The 28-pin surface-mount SOIC package supports conventional PCB assembly while providing enough I/O capacity for sensors, indicators, control inputs, and external logic. The Z8 processor architecture provides an 8-bit execution model optimized for control-oriented embedded systems. At 16 MHz, it offers substantially greater timing headroom than many simpler 8-bit controllers, while the compact instruction and memory architecture keeps firmware and peripheral integration straightforward. Programmable OTP options include an RC oscillator and EPROM protection, allowing the selected configuration to be fixed according to the product's operating requirements. Typical uses include appliance controllers, industrial control modules, security and access-control equipment, instrumentation peripherals, and small embedded control subsystems. In each case, the 24 available I/O lines and 125 bytes of RAM are important constraints. Designers should allocate RAM carefully for stacks, buffers, and intermediate state, while treating the 4 KB OTP capacity as the final firmware limit. The primary design consideration is that one-time-programmable memory cannot be changed after programming. Firmware validation, programming fixtures, and production traceability therefore must be completed before devices reach end users. PCB layouts should also follow the verified 28-SOIC footprint and provide the decoupling and clock circuitry required by the manufacturer datasheet. This page consolidates verified distributor specifications, sourcing links, family alternatives, and practical selection guidance. It also distinguishes documented device facts from pricing, lifecycle, and pin-level information that was not established by the supplied source data.

RFQ تماس
Z86E3116PEG - 8-Bit 16MHz 2KB OTP MCU | Zilog
Z86E3116PEG

Z86E3116PEG - 8-Bit 16MHz 2KB OTP MCU | Zilog

The Zilog Z86E3116PEG is an 8-bit Z8 microcontroller with 2KB (2K x 8) of one-time programmable program memory, 125 bytes of RAM, 24 I/O lines, and a maximum operating frequency of 16MHz in a 28-DIP (0.600-inch, 15.24mm) package. Its specified operating-voltage range is 4.5V to 5.5V. An 8-bit microcontroller is a compact embedded-control IC used to execute firmware, read inputs, and control outputs in dedicated electronic systems. The Z86E3116PEG belongs to the microcontroller hierarchy, combining a Z8 processor core, program memory, RAM, digital I/O, and embedded timing functions. Its one-time-programmable architecture is intended for products where firmware is written during manufacturing and does not need to be updated in the field. Key device characteristics include 16MHz operation, 24 general-purpose I/O lines, 125 bytes of RAM, and programmable OTP options identified in the source data as RC oscillator, EPROM protection, auto latch disable, and permanent settings. Integrated features reported by the Microchip USA product listing include a power-on reset and watchdog timer, providing basic startup supervision and recovery support for embedded control firmware. The device uses a 5V-class supply range of 4.5V to 5.5V. Its 28-DIP package provides through-hole mounting and a 0.600-inch body width, making it appropriate for legacy-style control boards, industrial controllers, appliance controllers, and compact embedded systems assembled with conventional through-hole techniques. Because the available product information does not include the complete datasheet pin map, individual signal assignments cannot be reproduced safely here. Typical application roles include simple sequencing and logic control, switch and relay management, status-indicator control, small industrial equipment interfaces, and dedicated appliance controllers. In each case, firmware stored in the 2KB OTP program memory determines the control behavior, while the 24 I/O lines provide connections to external sensors, switches, and actuators. Designers should account for the 4.5V to 5.5V supply requirement, confirm that the board uses the 28-pin DIP footprint, and validate timing, oscillator, reset, and watchdog behavior against the manufacturer datasheet before production release. The available data identifies the oscillator as internal, but its frequency range and detailed configuration requirements are not stated. This page consolidates verified distributor specifications, current sourcing information, package details, application guidance, and explicit data gaps. It also distinguishes verified facts from unspecified parameters, helping engineers evaluate the Z86E3116PEG without mistaking generic cross-reference tools for evidence of a pin-compatible replacement.

RFQ تماس
Z86E3116PSG - 16MHz 8-Bit Z8 MCU | Zilog
Z86E3116PSG

Z86E3116PSG - 16MHz 8-Bit Z8 MCU | Zilog

The Zilog Z86E3116PSG is an 8-bit Z8 microcontroller operating at 16 MHz, with 2 KB of one-time-programmable program memory, 125 bytes of RAM, and 24 general-purpose I/O pins. The device is packaged in a 28-pin DIP measuring 0.600 inches across the row spacing, or 15.24 mm. An 8-bit microcontroller is a compact embedded processor designed to execute control logic, monitor digital inputs, and operate peripherals using a relatively small instruction set and memory footprint. Within the embedded-control hierarchy, it belongs to the Z8 family of 8-bit microcontrollers and combines a CPU core, nonvolatile OTP program memory, RAM, timers, and general-purpose I/O in one integrated circuit. The Z86E3116PSG provides a 16 MHz operating frequency, a 2K x 8 OTP architecture, and 24 I/O pins. Its on-chip resources include two 8-bit timers, a power-on reset function, and a watchdog timer. OTP memory allows firmware to be programmed once during manufacturing or commissioning, making the device suitable for fixed-control products in which field updates are unnecessary. The Z8 architecture supports economical embedded-control designs while keeping the external component count relatively low. With 24 I/O pins, the device can directly interface with switches, indicators, relays, sensors, and discrete logic. Two timers support periodic tasks, input timing, debouncing, or basic event counting, while the watchdog timer provides a mechanism for recovering from unexpected program flow faults. Typical uses include appliance controls, small industrial controllers, building-control modules, simple sensor interfaces, LED and lighting controllers, and compact embedded products requiring a DIP footprint. The through-hole DIP package is particularly useful for prototypes, low-to-medium-volume products, and assemblies where socketed or manually inserted construction is preferred. Designers should verify each signal's electrical limits, oscillator requirements, programming method, and timing behavior against the manufacturer datasheet. Because OTP memory cannot be erased, firmware validation and manufacturing-programming controls are especially important. The 28-pin DIP footprint also requires adequate board space, connector accessibility, and mechanical clearance around the device. This page combines the Z86E3116PSG's principal memory, timing, I/O, and packaging characteristics with a focused drop-in alternative assessment, practical implementation guidance, and an application-oriented selection framework for compact Z8-based control designs.

RFQ تماس
Z86E3116SEG - 8-Bit 16MHz 2KB OTP MCU | Zilog
Z86E3116SEG

Z86E3116SEG - 8-Bit 16MHz 2KB OTP MCU | Zilog

The Zilog Z86E3116SEG is an 8-bit Z8 CISC microcontroller with 2KB of one-time-programmable program memory, 125 bytes of RAM, 24 I/O lines, and a 16MHz maximum operating frequency, supplied in a 28-pin SOIC package. It operates from a 4.5V to 5.5V supply across a -40°C to +105°C temperature range. A microcontroller is a programmable semiconductor that integrates a CPU, memory, digital I/O, and supporting peripherals into one package. The Z86E3116SEG belongs to the Z8 family of 8-bit microcontrollers, a class commonly used for embedded control because it combines a compact instruction set, dedicated I/O, and low-cost single-power-supply operation. Its larger program and data memories distinguish it from basic 8-pin devices while retaining the straightforward architecture suited to appliance controls, interface logic, and compact embedded systems. Key features include 2KB of OTP program memory, 125 bytes of RAM, 24 I/O lines, and operation up to 16MHz. Programmable OTP options listed in the device data include an RC oscillator, EPROM protection, auto latch disable, and permanent disable. The 28-pin SOIC package is also available in tube packaging according to the verified distributor data, supporting conventional through-hole board assembly rather than a compact surface-mount land pattern. The device uses the Z8 CISC architecture and includes an internal oscillator option according to the published specification summary. Its 125-byte RAM supports protocol state, counters, status flags, and short working buffers, while the 2KB OTP program area provides fixed firmware storage after programming. Because OTP memory cannot be electrically rewritten, firmware changes normally require a new programmed device rather than an in-circuit update. Typical uses include temperature controllers, appliance user interfaces, simple motor-control logic, industrial panel controllers, and embedded peripheral interfaces. In these applications, the 24 available I/O lines can distribute digital signals while the 16MHz operating rate supports time-based control routines and serial communication handling. A designer should still budget memory for interrupts, protocol handling, and application logic. The primary design constraint is nonvolatile program flexibility: OTP programming makes Z86E3116SEG appropriate for production builds with stable firmware, while applications requiring field updates may prefer a flash-memory MCU. Board layouts must also respect the 28-pin SOIC footprint and provide the required 4.5V to 5.5V supply, decoupling, programming interface, and exposed I/O routing. This product page consolidates verified distributor specifications, package information, temperature limits, and drop-in comparison data, then adds practical guidance on OTP programming, power-supply design, PCB layout, and selection constraints that are not presented as a complete replacement for the manufacturer datasheet.

RFQ تماس
Z86E3116SSG - 8-Bit 16MHz OTP MCU | Zilog
Z86E3116SSG

Z86E3116SSG - 8-Bit 16MHz OTP MCU | Zilog

The Zilog, Inc. Z86E3116SSG is an 8-bit Z8 microcontroller operating at up to 16 MHz, with 2 KB of one-time-programmable memory in a 28-pin SOIC package. It combines a compact embedded-control architecture with on-chip nonvolatile program storage for designs that do not require frequent firmware updates. The 28-pin surface-mount package provides dedicated I/O capacity while supporting compact control boards, household appliances, and dedicated embedded modules. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The Z8 belongs to the microcontroller hierarchy within integrated circuits and embedded processing. The Z86E3116SSG uses one-time-programmable memory, meaning its final firmware is written during manufacturing or production and cannot be rewritten afterward. This is useful for stable products where field updates are unnecessary and security through write protection is desirable. The device's headline characteristics are an 8-bit CPU architecture, a 16 MHz operating frequency, and 2 KB of OTP program memory. Its 28-pin SOIC package is designed for conventional surface-mount assembly and provides a practical upgrade from larger through-hole controllers when board area is constrained. Because the target MPN is identified as a Z8 2K OTP device, it is suited to compact control logic rather than connectivity-heavy or high-memory embedded systems. Program memory size is the principal design boundary. A 2 KB OTP budget supports a compact state machine, supervisory routine, keypad controller, or simple peripheral-control firmware, but it requires disciplined code sizing and limits the amount of application logic, tables, and diagnostics that can be included. The 16 MHz clock provides the timing headroom needed for responsive control loops, scanning, and communication routines, provided the firmware is designed around the limited code storage. Typical applications include appliance control modules, small motor-control boards, illumination controllers, keypads, security accessories, and compact embedded control products. A designer should assign ports according to the datasheet pin description table and reserve the programming and reset-related pins required by the selected Z8 device functions. The 28-pin package also makes it practical to retain through-hole-style prototyping while moving to automated surface-mount production. The primary engineering consideration is validating the complete firmware image before OTP programming. Because OTP cannot be revised after programming, functional testing, boundary-condition checks, and production traceability become especially important. Verify the oscillator, reset behavior, port multiplexing, and any peripheral configuration against the manufacturer datasheet before releasing devices for programming. This page combines manufacturer-oriented device identification, verified distributor specifications, same-family drop-in candidates, and practical design guidance for teams evaluating the Z86E3116SSG as a compact 8-bit control solution.

RFQ تماس
Z86E3116VSC - 16MHz 8-Bit Z8 OTP MCU | ZiLOG
Z86E3116VSC

Z86E3116VSC - 16MHz 8-Bit Z8 OTP MCU | ZiLOG

The ZiLOG Z86E3116VSC is an 8-bit Z8-family microcontroller operating at 16 MHz, with 2 KB of one-time-programmable program memory, 24 I/O lines, and operation from 3.5 V to 5.5 V. The device is packaged in a 28-pin square ceramic-chip carrier with J-leads, identified by package code QCCJ. Its combination of OTP memory, moderate I/O capacity, and compact surface-mount package makes it suitable for compact embedded-control products that require deterministic firmware storage and modest digital I/O. An 8-bit microcontroller is a complete embedded-processing component that executes firmware from internal program memory and uses digital inputs and outputs to control a product. Within the semiconductor hierarchy, the Z86E3116VSC belongs to the microcontroller class, integrates a CPU core, memory, timers, and I/O circuitry, and serves as the central controller in an embedded system. The Z8 name identifies ZiLOG's 8-bit architecture, while OTP memory permits a device to be programmed during manufacturing rather than repeatedly rewritten in the field. The principal device characteristics include a 16 MHz operating speed, 2 KB of OTP program memory, 125 bytes of RAM as reported in the component specification listing, and 24 I/O pins. One product listing describes a 4 KB OTP configuration, while the distributor listing identifies the Z86E3116VSC specifically as the 2 KB version. Designers should therefore use the manufacturer pin and memory tables for the exact ordering code and should not infer the target's program-memory capacity from the conflicting 4 KB description. The Z86E3116VSC is designed for compact control tasks such as appliance control, small industrial modules, instrumentation interfaces, and embedded products with modest processing requirements. Its 24 I/O lines can support digital sensing, actuation, indicators, and communication interfaces when the required peripheral functions and pin multiplexing allow. The 3.5 V to 5.5 V supply range accommodates both lower-voltage and conventional 5 V system rails, although external interface levels and timing must be checked against the device limits. The 28-pin QCCJ package is a legacy-style square ceramic-chip carrier with J-shaped terminals. Unlike a conventional leaded DIP package, it is intended for surface mounting and offers a compact footprint. Because the exact pin assignments are not published in the retrieved material, the complete pin map should be taken directly from the Zilog datasheet before schematic capture, footprint creation, or PCB routing. Designers should pay particular attention to OTP programming, supply decoupling, oscillator implementation, and unused-pin handling. OTP memory is suitable for permanent firmware but cannot accept field upgrades, so the programming process must occur during manufacturing. Power rails require local high-frequency bypass capacitance, while oscillator and I/O routing should minimize capacitive loading and switching noise. This product record combines the exact Z86E3116VSC ordering information with package, memory, voltage, timing, and I/O details, a quantified comparison against the nearest identified substitute family member, and practical guidance for programming and layout. It supports faster engineering triage while directing design-critical decisions to the manufacturer datasheet.

RFQ تماس
Z86E3312PSG - 8-Bit 12MHz Z8 MCU | Zilog
Z86E3312PSG

Z86E3312PSG - 8-Bit 12MHz Z8 MCU | Zilog

Zilog Z86E3312PSG is an 8-bit Z8 microcontroller operating at 12 MHz with 4 KB of one-time-programmable program memory, 237 bytes of RAM, and 24 general-purpose I/O pins. The device is housed in a 28-pin plastic DIP package and operates from a 4.5 V to 5.5 V supply. Its integrated peripherals include power-on reset, a watchdog timer, and EBI/EMI connectivity, making it suitable for compact embedded control systems, appliance controls, and simple peripheral interfaces. An 8-bit microcontroller is a programmable semiconductor that executes instructions from a defined instruction set while using registers, memory, and dedicated I/O circuitry to control a system. The Z86E3312PSG belongs to the Zilog Z8 family, combining a general-purpose embedded processor with on-chip memory and communication resources in one package. Its one-time-programmable memory allows a finished device to be programmed once for a specific application, which is useful for cost-sensitive controllers where field re-programming is unnecessary. The Z86E3312PSG combines a 12 MHz operating clock with 4 KB of OTP program memory and 237 x 8 bytes of RAM. Its 24 general-purpose I/O pins provide substantial parallel connectivity for switches, indicators, relays, displays, sensors, and external logic. Integrated power-on reset and watchdog-timer functions support dependable startup and recovery after faults. EBI/EMI resources add external bus or interface capability without requiring a separate protocol controller. The 4.5 V to 5.5 V operating range places the device in a classic 5 V embedded-control environment. A 5 V rail allows direct interfacing with many conventional 5 V logic families, although every external signal and supply rail must remain within the limits defined by the manufacturer datasheet. The 12 MHz clock provides the execution rate for control loops, state machines, user-interface scanning, and moderate data-processing tasks rather than high-throughput workloads. Typical uses include appliance and equipment controllers, building-control interfaces, LED and switch management, simple industrial modules, and embedded peripheral controllers. The 24 I/O pins are particularly useful when a design must connect multiple discrete inputs and outputs while retaining external-bus capability. A system can place the MCU between operator controls and actuators while using the watchdog timer to recover from firmware or communication stalls. Design around the DIP-28 footprint and verify all pin assignments from the manufacturer pin-description table before laying out the PCB. Place the device away from heat sources and follow the recommended decoupling arrangement for the 5 V supply. Because OTP memory cannot be rewritten, validate the complete firmware image before programming the production device and maintain a controlled manufacturing process. This product page consolidates the core electrical, memory, interface, lifecycle, and package characteristics of the Z86E3312PSG with practical application guidance. It also distinguishes verified functions from parameters that require confirmation in the manufacturer datasheet, helping engineers evaluate controller selection, PCB reuse, firmware planning, and production provisioning.

RFQ تماس
Z86E3312SSC - 8-Bit 12MHz OTP Microcontroller | Zilog
Z86E3312SSC

Z86E3312SSC - 8-Bit 12MHz OTP Microcontroller | Zilog

The Zilog Z86E3312SSC is an 8-bit Z8 microcontroller operating at up to 12 MHz with 4 KB of one-time-programmable ROM, 237 bytes of RAM, and 24 general-purpose I/O pins. It operates from a 4.5 V to 5.5 V supply and is packaged in a 28-pin SOIC measuring 7.50 mm wide. The combination of OTP program memory, an 8-bit CPU, and 24 I/O pins makes it suitable for compact embedded control, consumer equipment, and cost-sensitive products requiring one-time field programming. A microcontroller is a complete embedded processing system integrated on one semiconductor device. The Zilog Z8 family belongs to the hierarchy of microcontrollers, embedded processors, and programmable logic devices. Unlike a general-purpose microprocessor, this device includes program memory, data memory, I/O, timing, and interrupt resources on one chip. That integration reduces board size and component count while simplifying firmware development for embedded control tasks. The principal features include an 8-bit data bus, a 12 MHz maximum clock, 4 KB of OTP program memory, 237 bytes of RAM, and 24 general-purpose I/O pins. OTP memory allows a programmed image to be permanently stored in the finished device, which is useful for products that do not require field re-programming. The 24 I/O lines provide substantial peripheral connectivity for switches, sensors, indicators, actuators, and other discrete control signals. The Z8 architecture is designed for efficient embedded control rather than high-throughput computation. Its 8-bit internal architecture, organized program memory, and dedicated I/O capabilities support compact control loops and cost-sensitive product designs. EBI and EMI connectivity adds external-interface flexibility, while the 4.5 V to 5.5 V operating range supports conventional 5 V equipment. Because the program memory is OTP rather than flash, firmware should be finalized and tested before the programmed devices are released. Typical uses include appliance controllers, small motor-control systems, security and access-control equipment, LED-control modules, industrial interface boards, and compact consumer products. The 24 available I/O lines are particularly useful when a design requires multiple discrete inputs and outputs but does not need a large external memory interface. A 12 MHz clock also provides adequate processing performance for sensor sampling, state-machine logic, and simple communication protocols. PCB design should account for all 28 package leads and route sensitive signals away from noisy switching nodes. Confirm oscillator, reset, programming, and I/O assignments against the manufacturer pin-description table before layout release. Because OTP devices cannot be erased, production planning should include firmware verification and controlled programming to avoid unrecoverable program-memory errors. This product page combines the Z86E3312SSC architecture, package details, application guidance, and verified sourcing information with an explicit focus on design consequences. It also distinguishes confirmed drop-in replacements from merely related Z8 products, helping engineers avoid selecting a device with a different package or pinout.

RFQ تماس
Z86E3312SSG - 8-Bit 12MHz OTP Microcontroller | Zilog
Z86E3312SSG

Z86E3312SSG - 8-Bit 12MHz OTP Microcontroller | Zilog

Zilog Z86E3312SSG is an 8-bit Z8 microcontroller with a 12 MHz clock, 4 KB of one-time-programmable memory organized as 4K x 8, and 24 I/O ports. The device operates from a 4.5 V to 5.5 V supply and is listed as an active part in the Zilog Z86E3312 family. Its combination of OTP program memory, an 8-bit CPU, and a 5 V operating range makes it suitable for embedded control products requiring fixed-program logic and broad I/O access. An 8-bit microcontroller is a compact embedded-processing device that executes firmware from internal program memory and reads inputs through configurable digital ports. The Z86E3312 belongs to the Z8 family, a hierarchy that includes 8-bit microcontrollers, embedded processors, integrated circuits, and semiconductors. Zilog designed this controller for cost-sensitive appliances, access controls, industrial interfaces, and other systems where deterministic digital control is more important than high memory capacity or high-speed computation. The principal device parameters include a 12 MHz maximum clock frequency, 4 KB of OTP program memory, an 8-bit data bus, 24 I/O ports, and a 4.5 V to 5.5 V supply-voltage range. OTP memory allows the application program to be written during manufacturing and prevents subsequent modification, which supports application locking and production traceability. The 24 available I/O lines provide substantial connectivity for switches, sensors, indicators, relays, and communication peripherals. The Z86E3312SSG is identified as part of the Zilog Z8 microcontroller series and uses the SSG ordering code. Distributor records associate the device with the Z86E3312 family and identify its lifecycle as active. Because the detailed package dimensions, pin assignments, interrupt architecture, timer resources, and electrical timing limits are not stated in the cited product records, engineers should use the manufacturer datasheet and its pin-description table before finalizing a PCB layout. Typical uses for this controller include industrial control panels, appliance control boards, security and access-control equipment, programmable logic controllers, and compact instrumentation. In these applications, the 24 I/O ports can distribute control signals across a compact board, while the 12 MHz clock provides sufficient throughput for sequential logic, debouncing, state-machine execution, and periodic interface servicing. OTP programming is particularly appropriate when the finished control logic must remain fixed. The main design consideration is to verify the complete pinout, pin multiplexing, and peripheral assignments against the manufacturer datasheet before PCB routing. Designers should also confirm that every attached signal remains compatible with the 4.5 V to 5.5 V supply range and that firmware timing accounts for the 12 MHz operating limit. A Request a Quote form is available on this page for current commercial availability, lead time, and quantity requirements. This product record combines the exact Z86E3312SSG identity, core electrical and memory characteristics, lifecycle information, practical embedded-control applications, sourcing guidance, and a conservative drop-in assessment. It is designed to help engineers evaluate whether the MCU fits a fixed-program 8-bit design while separating confirmed specifications from details that still require direct manufacturer-document verification.

RFQ تماس
Z86E3312VSC - 8-Bit 12MHz 4KB OTP MCU | Zilog | Embedded Control
Z86E3312VSC

Z86E3312VSC - 8-Bit 12MHz 4KB OTP MCU | Zilog | Embedded Control

The Zilog Z86E3312VSC is an 8-bit Z8 microcontroller operating at up to 12 MHz, with 4 KB of one-time-programmable memory in a 28-pin PLCC package. It is designed for compact embedded-control tasks requiring a modest instruction set, one-time-programmable firmware storage, and a surface-mount package suitable for automated assembly. An 8-bit microcontroller is a semiconductor integrated circuit that executes embedded-control instructions from fixed program memory and interacts with external hardware through digital and analog peripherals. Within the product hierarchy, the Z86E3312VSC belongs to the microcontroller class of embedded processors. Its Z8 architecture is intended for cost-sensitive control logic, while the 4 KB OTP program memory is best suited to relatively compact firmware rather than connectivity-heavy or graphics-oriented applications. Key device characteristics include an 8-bit processor core, 4 KB of OTP program memory, a 12 MHz operating frequency, and a 28-pin J-lead PLCC package. OTP memory allows the final firmware image to be programmed during manufacturing, which is useful for products whose firmware is stable and does not require field updates. The 12 MHz clock rate provides additional processing headroom for peripheral servicing and structured control routines compared with slower general-purpose 8-bit controllers. The PLCC package provides a defined lead arrangement and supports compact, high-density PCB layouts, although it requires adequate spacing and controlled assembly for its J-shaped leads. Because the MCU is designed around OTP rather than flash memory, engineers should establish the firmware requirements and programming process early in development. The manufacturer datasheet remains the authoritative source for clock, electrical, timing, programming, and peripheral details before schematic capture. Typical uses include simple industrial control modules, appliance controllers, building automation endpoints, lighting controllers, sensor-conditioning systems, and compact embedded products where 4 KB of OTP code is sufficient. The device is also appropriate for low-cost dedicated controllers that monitor digital inputs, operate actuators, and require deterministic operation without user-accessible firmware updates. The primary design consideration is program-memory capacity. Engineers should confirm that application code, interrupt handlers, lookup tables, and boot requirements fit within 4 KB before selecting the MCU, and should verify all 28 package connections against the manufacturer pin description. Clock settings, timing margins, I/O limits, and programming signals must also be reviewed in the manufacturer datasheet before release to production. This product record combines the exact package and core specifications, practical embedded-control applications, structured comparison parameters, and design guidance for engineers evaluating the Z86E3312VSC. It is intended to accelerate component selection while keeping final design decisions tied to the manufacturer documentation.

RFQ تماس
Z86E3412PSC - 8-Bit 12MHz OTP Microcontroller | Zilog
Z86E3412PSC

Z86E3412PSC - 8-Bit 12MHz OTP Microcontroller | Zilog

The Zilog Z86E3412PSC is an 8-bit Z8 CMOS microcontroller operating at up to 12 MHz, with 16 KB of one-time-programmable program memory, 237 bytes of RAM, and a 28-pin PDIP package. It is designed for compact embedded-control systems that require deterministic digital I/O, low-cost ROM-based program storage, and operation from a 3.5 V to 5.5 V supply. A microcontroller is a programmable semiconductor that combines a CPU core, memory, and peripheral functions on one integrated circuit. The Z8 belongs to the broader 8-bit microcontroller category within embedded processors and embedded logic devices. The Z86E3412PSC uses one-time-programmable memory, allowing the application program to be written once during manufacturing or final programming rather than rewritten in the field. The device features an 8-bit data bus, a maximum clock frequency of 12 MHz, and 16 KB organized as 16K x 8 bits of OTP program memory. Its 237 bytes of RAM provide working space for variables, stack operations, and control state. The commercial-temperature component is supplied in a through-hole PDIP-28 package, simplifying prototype assembly, inspection, and hand soldering. The Z8 core is intended for embedded applications where modest computational throughput is sufficient. At 12 MHz, the device can handle digital control, sequencing, keypad or switch input processing, discrete output control, and status indication without requiring a separate processor. Because program storage is OTP rather than reprogrammable flash, firmware changes require a new programmed device, so firmware validation must occur before final programming. Typical uses include appliance control panels, small industrial control modules, instrumentation interfaces, programmable timers, LED status systems, and dedicated sequence controllers. The 28-pin through-hole format is particularly useful where boards are assembled manually or where a socketed controller simplifies replacement during prototype validation. The absence of USB, SPI, I2C, UART, and CAN channels makes it most appropriate for designs centered on parallel digital control rather than modern serial connectivity. Designers should plan the power rail for 3.5 V to 5.5 V operation and assign unused pins according to the manufacturer pin-description table. Because OTP memory cannot be erased, validate the complete firmware image before programming the production parts. Confirm reset, oscillator, and I/O requirements against the Zilog datasheet before releasing the PCB footprint. This page combines the Z86E3412PSC device specifications, package details, sourcing information, comparison parameters, and practical design guidance in one engineering-focused reference. It also identifies the directly comparable Z86E3412PSG and clearly distinguishes what is confirmed from information that requires confirmation.

RFQ تماس
Z86E3412PSG - 8-Bit 12MHz 16KB OTP MCU | Zilog
Z86E3412PSG

Z86E3412PSG - 8-Bit 12MHz 16KB OTP MCU | Zilog

Zilog, Inc. Z86E3412PSG is an 8-bit CMOS Z8 microcontroller operating at up to 12 MHz, with 16 KB of one-time-programmable program memory in a 28-pin through-hole DIP package. Its operating supply range is 5.00 V to 5.50 V, making it a directly powered embedded-control component for compact legacy-control systems. An MCU, or microcontroller, is a single semiconductor integrating a processor core, program memory, data memory, and peripherals on one die. Within the embedded-control hierarchy, the Z8 family belongs to the broader category of 8-bit microcontrollers and combines a compact instruction set with application-specific peripherals. Its OTP memory makes the device suitable for products where firmware is finalized during manufacturing and field reprogramming is unnecessary. The principal specifications of the Z86E3412PSG are its 8-bit CPU architecture, 12 MHz maximum clock frequency, and 16 KB OTP program memory organized as 16K x 8. The device is identified as a CMOS Z8 microcontroller, while the manufacturer and distributor listings place it in the 28-pin DIP class. These characteristics distinguish it from devices that require external program memory or provide flash-based field updates. The Z86E3412PSG belongs to the Z86E3412 family and is designed for embedded control rather than high-performance computing. OTP program storage gives the manufacturer a defined, permanently programmed firmware path and can support repeatable production across an appliance or controller. The 12 MHz operating rate provides more timing headroom than many low-pin-count 8-bit controllers while retaining the simplicity of a compact MCU architecture. Typical applications include dedicated appliance controllers, small motor-control boards, keypads, sensor-interface modules, and simple sequence controllers. Its 28-pin DIP format is useful for prototypes, repairable assemblies, and through-hole production where a QFP package would be unnecessary. A system designer should verify peripheral assignments, interrupt behavior, and timing requirements against the device's pin description and application information. A critical design consideration is that OTP memory cannot be erased and rewritten in the field. Firmware changes therefore require a new programmed device or a board-level replacement strategy. Decoupling, oscillator layout, I/O drive, and programming should be implemented according to the manufacturer datasheet, especially in electrically noisy motor or relay-control environments. This product page combines the manufacturer device identity with focused design guidance, verified package and memory details, application analysis, and same-family replacement considerations. It is intended to help engineers confirm fit, assess programming constraints, and plan a reliable embedded-control implementation before requesting an order.

RFQ تماس
Z86E3412SEG - 8-Bit 12MHz 16KB OTP MCU | Zilog
Z86E3412SEG

Z86E3412SEG - 8-Bit 12MHz 16KB OTP MCU | Zilog

The Zilog Z86E3412SEG is an 8-bit Z8 microcontroller operating at 12 MHz with 16 KB of one-time-programmable memory in a 28-pin SOIC package. Its operating voltage range is 3.5 V to 5.5 V, making it suitable for embedded control systems that require a compact, nonvolatile program memory and an 8-bit processing architecture. A microcontroller is a programmable semiconductor that integrates a CPU core, program memory, data memory, and peripherals into one device. The Z8 belongs to the broader 8-bit MCU category, where the embedded processor executes firmware to monitor inputs and control outputs. Unlike a general-purpose microprocessor, the Z86E3412SEG is designed for compact embedded-control tasks such as appliance control, simple industrial interfaces, and embedded peripheral control. The Z86E3412SEG's principal specifications include its 8-bit CPU, 12 MHz operating frequency, and 16 KB of OTP memory. The OTP program memory provides a stable, nonvolatile place for firmware because its contents cannot be erased after programming. The device is also listed with 237 bytes of data memory and a 3.5 V to 5.5 V supply range. Its 28-SOIC package supports conventional PCB assembly and is available in a 300 mil body format. The Z8 architecture is intended for straightforward embedded workloads where deterministic control, compact code size, and low component count are more important than high computational throughput. At 12 MHz, the processor is suitable for polling multiple inputs, executing control logic, communicating through serial peripherals, and managing discrete or analog interface functions. Exact peripheral assignments, interrupt behavior, and electrical limits should be checked against the manufacturer documentation before final circuit implementation. Typical uses include household appliance controllers, small motor-control boards, temperature or level monitoring products, programmable interface modules, and compact industrial automation equipment. In these systems, the MCU can execute startup routines, acquire sensor information, update displays or indicators, and operate actuator outputs while keeping the external hardware count low. Designers should begin with the manufacturer's pin-description table when assigning PCB nets and should preserve the device's documented power, ground, reset, clock, and programming connections. Because the MCU is intended for OTP programming, firmware development must account for the non-erasable program memory. Decoupling, oscillator stability, programming access, and unused-pin treatment should follow the device's recommended application circuit and layout guidance. This product page consolidates the exact orderable MPN, core architecture, memory and frequency specifications, package details, sourcing guidance, and engineering considerations. It also distinguishes confirmed orderable information from characteristics that require the manufacturer datasheet, helping engineers plan sourcing and hardware development without confusing this 28-SOIC device with packages or variants that have different pin assignments.

RFQ تماس
Z86E3412SSG - 12MHz 16KB OTP 8-Bit MCU | Zilog
Z86E3412SSG

Z86E3412SSG - 12MHz 16KB OTP 8-Bit MCU | Zilog

The Zilog Z86E3412SSG is an 8-bit Z8 Z8 One-Time Programmable microcontroller with a 12 MHz clock, 16 KB of OTP program memory organized as 16K x 8, and a 28-pin SOIC package. It is designed for embedded control applications that require a compact 8-bit controller, nonvolatile program storage, and a peripheral-oriented MCU architecture. An 8-bit microcontroller is a microprocessor and embedded-control IC built around an 8-bit processing architecture. The Z8 family belongs to the broader hierarchy of embedded processors, microcontrollers, and semiconductors. One-time programmable memory allows firmware to be written once during manufacturing or programming, providing nonvolatile program storage without the removable-program-memory cost of EEPROM. This makes the Z86E3412SSG suitable for fixed-function products whose firmware does not need field updates. The principal device characteristics include a 12 MHz operating frequency, 16 KB of OTP program memory, 8-bit processing, CMOS construction, and a 28-pin SOIC package. The reported operating-temperature range for this exact ordering code is 0°C to +70°C. The part is also identified as Pb-free, although separate RoHS, REACH, and halogen-free declarations were not included in the supplied source data and therefore remain unconfirmed. The 12 MHz clock rate provides the timing headroom expected from a Z8-class embedded controller, while the 16K x 8 OTP organization determines the available program address space. Because the source data does not provide RAM capacity, I/O pin assignments, peripheral inventories, electrical limits, watchdog behavior, or timing characteristics, those details must be confirmed in the manufacturer datasheet before a board design is released. Typical uses include fixed-function industrial controllers, appliance-control panels, small instrument controllers, status interfaces, and embedded control modules where an 8-bit processor and OTP firmware storage are sufficient. Its 28-pin SOIC package also supports conventional surface-mount assembly, but package dimensions, pin geometry, and exposed thermal requirements are not included in the supplied evidence. For new layouts, engineers should verify the complete 28-pin pinout, required decoupling, oscillator connection, programming method, reset requirements, and absolute maximum ratings against the official datasheet. The OTP programming process should also be coordinated with manufacturing because an incorrectly programmed device generally cannot be rewritten like flash memory. This page consolidates the verified distributor listings, an identified same-package family alternative, package constraints, pricing evidence, and engineering-selection guidance. It also clearly separates confirmed Z86E3412SSG facts from electrical and programming details that require manufacturer documentation.

RFQ تماس