Analog Devices

ADM489ABRMZ - 5V Full-Duplex RS-485 Transceiver | ADI

MPN: ADM489ABRMZ ✓ فعال
4.5 V to 5.5 V Vdss EIA RS-422 and EIA RS-485 Rds(on) 10-pin MSOP Package
حداقل سفارش: 1 |

ADM489ABRMZ نمای کلی

Analog Devices ADM489ABRMZ is a 5 V, full-duplex differential line transceiver for balanced RS-422 and RS-485 communication, operating from a 4.5 V to 5.5 V supply at up to 250 kbps in a 10-pin MSOP package. It combines one differential line driver and one differential receiver in a low-power interface suitable for multipoint bus transmission lines.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and receives differential signals from the bus. The differential signaling method supports noise immunity and reliable communication over longer cable runs. Within the interface IC hierarchy, the ADM489ABRMZ is a physical-layer line transceiver designed for industrial data links, instrumentation, factory equipment, and embedded control networks.

The principal operating characteristics are a 4.5 V to 5.5 V supply range, 250 kbps maximum signaling rate, full-duplex operation, and support for both EIA RS-422 and EIA RS-485. The device is described by Analog Devices as a low-power, slew-rate-limited transceiver. Slew-rate limitation reduces the high-frequency energy imposed on the bus, helping reduce electromagnetic interference and unwanted reflections on correctly terminated networks.

The ADM489A family uses a mixed BiCMOS process that combines low-power CMOS circuitry with fast-switching bipolar technology. Its single driver and receiver arrangement provides separate transmit and receive paths, allowing simultaneous two-way communication. Because it is a full-duplex device, the associated bus implementation normally uses a dedicated differential pair for transmission and another pair for reception rather than sharing one half-duplex pair.

Typical uses include industrial control links, remote sensor interfaces, building automation equipment, test and measurement systems, and factory automation networks. The 250 kbps rate is appropriate for moderate-speed control and monitoring traffic rather than high-speed Ethernet or other protocols requiring much greater bandwidth. Its 10-pin MSOP format supports compact, surface-mount PCB layouts.

Designers should verify the supply rails, driver and receiver enable functions, bus topology, cable length, and termination requirements against the ADM489A datasheet. A 120-ohm termination resistor is commonly placed at each physical end of a correctly terminated RS-485 bus, while unused driver and receiver paths must be configured according to the device instructions. Decoupling and differential-routing practices are also important for reliable operation.

This page combines the ADM489A product information with interface selection guidance, comparison parameters, and application-focused design notes. It is intended to help engineers determine whether the 5 V, 250 kbps, full-duplex MSOP transceiver fits a specific balanced communication link before beginning PCB implementation.

جایگزین‌های drop-in برای ADM489ABRMZ — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

هیچ جایگزین مستقیمی برای این محصول موجود نیست.

درخواست جایگزین

ADM489ABRMZ مشخصات

Product Type Full-duplex differential line transceiver
Supported Standards EIA RS-422 and EIA RS-485
Supply Voltage Range 4.5 V to 5.5 V
Nominal Supply Voltage 5 V
Maximum Data Rate 250 kbps
Driver Configuration 1 differential line driver
Receiver Configuration 1 differential line receiver
Communication Mode Full duplex
بسته‌بندی 10-pin MSOP
نوع نصب Surface mount
Slew Rate Limited
Power Class Low power
Process Technology BiCMOS
Bus Application Multipoint balanced data transmission

راهنمای پیکربندی پین ADM489ABRMZ 10-pin msop

پیکربندی پین برای ADM489ABRMZ (پکیج 10-pin msop). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 10-pin msop برای ADM489ABRMZ

داده پین‌آوت تفصیلی موجود نیست برای ADM489ABRMZ.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

ADM489ABRMZ مناسب است برای 6 کاربردs: Industrial PLC and Factory Automation Links, Remote Sensor and Instrumentation Networks, Building Automation and Environmental Control, Test and Measurement Equipment, Security and Surveillance Systems, Embedded Control and Communications Modules.

🏭

Industrial PLC and Factory Automation Links

The ADM489ABRMZ fits industrial control networks that need reliable balanced communication between a controller and remote I/O, drives, sensors, or operator panels. Its 4.5 V to 5.5 V supply integrates with conventional 5 V control electronics, while full-duplex operation allows transmit and receive traffic to proceed independently. The 250 kbps rate is suitable for supervisory and control traffic rather than high-bandwidth factory data. A full-duplex implementation should provide separate driver and receiver pairs, use short branches, and apply bus termination only at the physical endpoints. Industrial cabling and protection requirements should also be considered because the transceiver itself is the interface between logic-level circuitry and externally accessible wiring.

🧩

Remote Sensor and Instrumentation Networks

The ADM489ABRMZ can connect a controller to distributed sensors, measurement modules, analyzers, and remote data-acquisition units over a balanced RS-485 bus. Differential signaling improves tolerance of common-mode noise compared with single-ended transmission, making the interface appropriate for instrumentation distributed across a machine or facility. The 250 kbps maximum rate supports moderate polling and monitoring traffic while the 10-pin MSOP package preserves board area. Designers should base cable length and baud rate on the ADM489A application guidance, use twisted differential wiring, and ensure that grounding and isolation strategy are compatible with the installation. Any exposed cable also requires appropriately selected surge and ESD protection.

🏠

Building Automation and Environmental Control

The ADM489ABRMZ is applicable to building-automation controllers communicating with distributed HVAC, lighting, access-control, and environmental monitoring modules. Its low-power 5 V interface can support full-duplex balanced links without requiring a high-speed transceiver architecture, and the 250 kbps rate is adequate for supervisory commands and status updates. The compact MSOP package supports dense controller boards. In installations spanning buildings or power zones, verify ground-potential differences, add suitable isolation or protection where required, and avoid allowing transient surges on external wiring to reach the transceiver. Firmware should also manage driver enable timing so that only the intended node transmits on the bus.

🖥️

Test and Measurement Equipment

The ADM489ABRMZ can link laboratory instruments, remote test heads, automated test equipment, and data-acquisition modules through a balanced RS-485 or RS-422 connection. Full-duplex operation allows control traffic and measured responses to use separate differential paths, reducing the need to time-share a half-duplex bus. The 250 kbps rate is suitable for many low- and moderate-speed instrument-control protocols. Because test systems may expose the bus to long cables or laboratory ground differences, the design should carefully evaluate common-mode range, isolation, connector pin assignments, and surge protection. A controlled reference plane and closely routed differential pair remain important even when cable lengths are short.

🎥

Security and Surveillance Systems

The ADM489ABRMZ is suitable for wired supervisory links between surveillance controllers, access-control panels, and remote field devices. Balanced differential communication helps maintain data integrity where cables run near switching equipment, motors, or other potential noise sources. The 250 kbps rate is more than adequate for command, status, and event traffic, while the 10-pin MSOP package supports compact peripheral boards. Security installations frequently use long exterior cable runs, so designers should specify transient protection, grounding or isolation appropriate to the site, and connector shielding. The bus must also be configured to prevent multiple transmitters from driving the line simultaneously.

🔧

Embedded Control and Communications Modules

The ADM489ABRMZ can serve as the field-bus interface for an embedded controller, data logger, motor controller, or compact communications module. The 5 V supply range supports common embedded rails, and the 250 kbps limit aligns with many proprietary control protocols, configuration links, and remote command interfaces. Full-duplex operation is useful when continuous status feedback and command traffic must coexist. Because the 10-pin MSOP package is compact, placement still requires careful attention to thermal conditions and exposed-pin layout. Designers should follow the manufacturer guidance for bypassing, driver enable state, receiver output behavior, and bus termination, particularly when the module is designed for field replacement across installations with unknown cabling.

What is the ADM489ABRMZ used for?
The ADM489ABRMZ is a 5 V, full-duplex differential transceiver used for balanced RS-422 and RS-485 data links. It contains one differential line driver and one differential receiver, supports communication rates up to 250 kbps, and operates from a 4.5 V to 5.5 V supply. Analog Devices describes the ADM489A family as low-power devices intended for multipoint bus transmission lines.
What is the operating voltage of ADM489ABRMZ?
The ADM489ABRMZ operates from 4.5 V to 5.5 V, making it a 5 V interface device. According to the Analog Devices ADM489A product information, the device is intended for RS-422 and RS-485 balanced communication. The 5 V supply requirement should be checked against the logic levels of the host controller and the system power architecture before PCB implementation.
What is the maximum data rate of ADM489ABRMZ?
The ADM489ABRMZ supports a maximum signaling rate of 250 kbps. This rate is appropriate for industrial control, sensor monitoring, and other moderate-speed differential communication links. The Analog Devices ADM489A datasheet identifies the part as a low-power, slew-rate-limited EIA RS-485 transceiver; the actual usable link rate can also depend on cable length, topology, termination, and system timing.
Is ADM489ABRMZ half-duplex or full-duplex?
The ADM489ABRMZ is a full-duplex transceiver. It includes a differential driver for transmitting data and a differential receiver for receiving data, allowing the two directions to operate independently. The Analog Devices product description identifies the ADM489A as a full-duplex line transceiver. A full-duplex implementation normally requires separate differential pairs for transmit and receive.
Where can I download the ADM489ABRMZ datasheet PDF?
The official Analog Devices ADM489A product page provides access to the manufacturer documentation for the ADM489A family, including the ADM489ABRMZ. The page is available at https://www.analog.com/en/products/adm489a.html. Use the manufacturer's pin-description table, electrical characteristics, and application guidance when assigning pins and planning the RS-422 or RS-485 interface circuit.
Where can I find the ADM489ABRMZ pinout?
The ADM489ABRMZ pin assignment is documented in the Analog Devices ADM489A datasheet on the official product page at https://www.analog.com/en/products/adm489a.html. The component uses a 10-pin MSOP package. Use the datasheet pin-description table for exact driver, receiver, enable, supply, and ground connections because package drawings alone do not identify the functional pin names.
What can replace the ADM489ABRMZ?
The closest listed same-footprint choice is the ADM489ABRMZ-REEL7, which is the reel-packaging form of the ADM489ABRMZ and retains the same 10-pin MSOP device characteristics. It can serve as a procurement or assembly substitute when its reel format is acceptable, although it is not a distinct pinout alternative. Use the Analog Devices ADM489A documentation to confirm electrical compatibility before substitution.
Is ADM489ABRMZ the same as ADM489ABRMZ-REEL7?
The ADM489ABRMZ and ADM489ABRMZ-REEL7 are the same 10-pin MSOP transceiver offered with different order packaging. Both are identified as full-duplex RS-422/RS-485 5 V transceivers, while the target is also specified for operation at up to 250 kbps. The practical distinction is the reel-packaging designation, so confirm the required ordering format before substitution.
When should I choose ADM489ABRMZ for an RS-485 interface?
Choose the ADM489ABRMZ when the design needs a 5 V, full-duplex RS-485 or RS-422 interface operating at 250 kbps or less in a compact 10-pin MSOP package. Its separate differential driver and receiver support simultaneous two-way communication. Confirm that the required bus voltage, common-mode range, logic thresholds, and cable length fall within the limits published in the ADM489A datasheet.
Is ADM489ABRMZ suitable for industrial automation and factory networks?
The ADM489ABRMZ is suitable for industrial automation links that operate at moderate speed and use balanced differential wiring. Its 4.5 V to 5.5 V supply, full-duplex RS-485/RS-422 operation, and 250 kbps maximum rate fit control, monitoring, and remote-sensor communications. The linked components, connectors, surge protection, grounding, and cable construction must be selected for the installation environment.
What is the best cross-brand equivalent for ADM489ABRMZ?
No cross-brand drop-in equivalent can be identified with sufficient pin-level and parametric support from the available cross-reference information. A valid replacement must match the 10-pin MSOP footprint, provide compatible RS-422/RS-485 driver and receiver functions, operate from 4.5 V to 5.5 V, and support the required data rate. Use the Request a Quote form to request help qualifying a specific cross-brand candidate.
What is the ADM489ABRMZ versus ADM489ABRMZ-REEL7 difference?
The electrical role of the ADM489ABRMZ and ADM489ABRMZ-REEL7 is the same: both are 10-pin MSOP, full-duplex RS-422/RS-485 transceivers for 5 V systems. The meaningful documented difference is order packaging, with the REEL7 designation identifying the reel format. The target operates from 4.5 V to 5.5 V and supports signaling up to 250 kbps.
How should termination and routing be handled for ADM489ABRMZ?
Use a correctly terminated RS-485 bus with 120-ohm termination resistors at the two physical ends, while avoiding unnecessary termination on intermediate nodes. Route the differential pair as a tightly coupled pair over a continuous reference plane and keep stubs short. The Analog Devices ADM489A datasheet should guide driver enable control, unused-line handling, grounding, and protection selection.
How much power does the ADM489ABRMZ interface require?
The ADM489ABRMZ is designed as a low-power 5 V interface IC, but its exact supply-current behavior depends on operating mode, bus loading, driver state, and the selected supply voltage. The manufacturer lists a 4.5 V to 5.5 V operating range. Use the Analog Devices ADM489A electrical-characteristics table for load-specific supply current and quiescent-current values when calculating power consumption.
What are the key specifications of ADM489ABRMZ that engineers should know?
The key ADM489ABRMZ specifications are a 4.5 V to 5.5 V supply, operation up to 250 kbps, full-duplex communication, one differential driver, one differential receiver, and a 10-pin MSOP package. Analog Devices also identifies the device as compliant with EIA RS-422 and RS-485 requirements and suitable for multipoint balanced transmission. Exact common-mode limits and logic thresholds should be taken from the manufacturer datasheet.
Where can I buy ADM489ABRMZ and what is the lead time?
The ADM489ABRMZ can be requested through the Request a Quote form on this page. Current commercial terms, including quantity availability, lead time, and order processing, should be confirmed when submitting the request. The device is identified as a 10-pin MSOP, 5 V, full-duplex RS-422/RS-485 transceiver, so the requested suffix and package should remain unchanged.

داده‌های مرجع مهندسی برای ADM489ABRMZ — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the ADM489ABRMZ when a design requires a compact, 5 V, full-duplex interface for balanced RS-422 or RS-485 communication at 250 kbps or less. Its one-driver, one-receiver arrangement is appropriate when transmit and receive traffic must operate independently, and the 10-pin MSOP package simplifies space-constrained board layouts. The ADM489ABRMZ-REEL7 offers the same device in a reel-packaging order format and is appropriate when that delivery format matches the assembly process. Do not treat a differently packaged or differently pinned transceiver as a drop-in substitute without verifying every pin, enable state, supply threshold, and bus specification. For new cross-brand sourcing, the qualified replacement must match the 10-pin MSOP footprint, 4.5 V to 5.5 V supply, RS-422/RS-485 functions, and required data rate. When the design exceeds 250 kbps, requires automatic fail-safe behavior not established for this device, or needs integrated isolation, choose an interface whose published electrical characteristics directly satisfy those requirements.

مقایسه با جایگزین‌ها

پارامتر این محصول
Package 10-pin MSOP
Brand Analog Devices
Product Type Full-duplex differential line transceiver
Supported Standards EIA RS-422 and EIA RS-485
Supply Voltage Range 4.5 V to 5.5 V
Maximum Data Rate 250 kbps
Driver Count 1 differential line driver
Receiver Count 1 differential line receiver
Slew Rate Limited
Process Technology BiCMOS

تفاوت‌های کلیدی

  • Full-duplex operation with separate differential paths (در مقابلADM489ABRMZ-REEL7)
  • Compact 10-pin MSOP implementation (در مقابلADM489ABRMZ-REEL7)
  • Supports both RS-422 and RS-485 balanced links (در مقابلADM489ABRMZ-REEL7)

یادداشت‌های طراحی

Route the ADM489ABRMZ differential driver and receiver conductors as tightly coupled pairs over a continuous ground reference. Keep the transceiver, bypass capacitor, and protection components close to their corresponding pins. Minimize stub branches and avoid sharing differential routing with unrelated digital signals, because discontinuities and mismatched traces can increase reflections and reduce communication margin.

Configure unused driver and receiver paths exactly as directed in the ADM489A datasheet, and ensure that only one node enables its transmitter at a time. On an RS-485 bus, place 120-ohm termination resistors at the two physical ends rather than at every connected device. Incorrect termination, excessive stub length, or simultaneous active drivers can prevent reliable reception even when the local transmitter is operating correctly.

The ADM489ABRMZ uses slew-rate-limited signaling, but good EMC performance still depends on the complete interface. Use a controlled cable impedance, keep the differential pair together, provide a solid reference plane, and place common-mode or surge-protection components at the connector or board entry point. Confirm protection-device capacitance and clamping behavior so the added loading does not impair communication at the selected line rate.

The device operates from a 4.5 V to 5.5 V supply. Place the recommended bypass capacitor close to the supply pins and keep supply-current return paths compact. When calculating the interface power budget, include not only quiescent consumption but also driver load-dependent current and the current drawn by attached protection devices. Use the manufacturer electrical-characteristics table for operating-mode current because bus loading changes the total demand.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The Analog Devices product information identifies EIA RS-422 and EIA RS-485 compliance. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated in the available product information.

تاریخ تأیید داده‌ها: 2026-11-19 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

ADM489ABRMZ datasheet ADM489ABRMZ pinout ADM489ABRMZ datasheet pdf Analog Devices ADM489ABRMZ ADM489ABRMZ equivalent ADM489ABRMZ replacement ADM489ABRMZ cross reference ADM489ABRMZ vs ADM489ABRMZ-REEL7 ADM489ABRMZ MSOP-10 footprint ADM489ABRMZ 250kbps RS-485 ADM489ABRMZ application circuit ADM489ABRMZ price ADM489ABRMZ stock what can replace ADM489ABRMZ

قطعات و اصطلاحات مرتبط

Analog Devices ADM489ABRMZ ADM489A ADM489ABRMZ-REEL7 RS-485 RS-422 differential line transceiver full-duplex transceiver interface IC balanced data transmission multipoint bus differential driver differential receiver slew-rate-limited signaling BiCMOS 250 kbps 4.5 V to 5.5 V 10-pin MSOP surface mount industrial automation building automation test and measurement 120-ohm termination EIA standards
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ