ATSAME54P19A-AUT-EFP - 120MHz Cortex-M4F MCU 512KB Flash | Microchip
MPN: ATSAME54P19A-AUT-EFP ✓ فعالATSAME54P19A-AUT-EFP نمای کلی
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data memory, and peripheral interfaces on one die. The ATSAME54 belongs to the SAM E54 series, which sits in Microchip's high-performance MCU portfolio alongside the SAM D5x family, targeting applications that require Cortex-M4 class DSP and FPU performance plus high-speed connectivity such as USB, Ethernet, and CAN-FD. Within the system hierarchy, this MCU is a processing subsystem that interfaces with sensors, communication transceivers, and memory, typically powered by 3.3 V and managed via an RTOS or bare-metal firmware.
The ATSAME54P19A-AUT-EFP integrates 512 KB of dual-bank Flash with ECC, 192 KB SRAM, a full-speed USB 2.0 High-Speed interface, 10/100 Mbps Ethernet MAC with 1588 PTP support, CAN-FD, SD/MMC host, and a QSPI/SPI interface for external memory expansion. It also includes a 12-bit 1 Msps ADC, dual 12-bit DACs, analog comparators, and a hardware cryptographic accelerator (AES, SHA, TRNG) for secure connectivity. Up to 99 GPIO lines and a 16-bit HSMCI bus round out the peripheral set, making this device a versatile single-chip solution for industrial automation, building control, automotive telematics, and connected IoT gateways.
The Cortex-M4F core delivers 150 DMIPS / 600 CoreMark performance, supported by a tightly coupled memory (TCM) interface, a Memory Protection Unit (MPU), and a single-precision FPU that accelerates floating-point math for sensor fusion, audio processing, and motor control loops. The device supports Sleep, Idle, Standby, and Backup modes with RTC retention down to a few microamps, enabling battery-friendly field deployments. Built on a low-power 65 nm CMOS process, the chip balances high performance with deterministic interrupt latency.
Typical applications include industrial control HMI panels, automotive gateway ECUs, building automation controllers, USB/Ethernet-connected IoT edge nodes, smart energy metering with TLS encryption, and factory automation PLCs. The Extended Flash Performance variant is particularly suited to designs requiring 100 k cycle endurance and 20-year data retention, such as firmware update logging or OBD-II telemetry recorders.
When designing with this device, allocate careful attention to the 128-pin TQFP power and decoupling network: at least one 4.7 uF bulk plus a 100 nF decoupling capacitor per VDD pin pair is recommended, and the analog AVDD rail should be filtered with a ferrite bead from the digital supply. For Ethernet applications, route the RMII traces as a 50 ohm controlled-impedance group with matched lengths to the PHY.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the standalone manufacturer datasheet or single distributor listing.
جایگزین‌های drop-in برای ATSAME54P19A-AUT-EFP — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای ATSAME54P19A-AUT-EFP (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در USB, Package, Operating Temperature, RoHS Status, SRAM.
ATSAME54P19A-AUT
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
ATSAME54P19A-AU-EFP
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ATSAME54P20A-AUT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ATSAME54N20A-AUT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ATSAME54N19A-AUT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ATSAMD51P19A-AUT
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
ATSAME54P19A-AUT-EFP حداکثر مقادیر مجاز و مشخصات الکتریکی
| Series | SAM E54 |
| Core | ARM Cortex-M4F |
| Core Size | 32-Bit Single-Core |
| Maximum CPU Speed | 120 MHz |
| Program Memory Size | 512 KB (512K x 8) Flash with ECC |
| RAM Size | 192 KB SRAM with ECC |
| Operating Voltage | 3.3 V (1.71V to 3.6V core/IO supply range) |
| I/O Pins | 99 |
| بسته‌بندی | 128-TQFP (14x14 mm) |
| نوع نصب | Surface Mount |
| Packaging | Tape & Reel (AUT) |
| دمای کاری | -40C to +85C (Automotive Grade) |
| Flash Endurance | Extended (EFP - higher endurance and retention) |
| Connectivity | USB 2.0 High-Speed, Ethernet 10/100 MAC, CAN-FD, SD/MMC, QSPI, I2C, SPI, UART |
| ADC | 12-bit, 1 Msps |
| DAC | Dual 12-bit |
| Cryptography | AES, SHA, TRNG (hardware accelerator) |
| وضعیت RoHS | Compliant |
پیکربندی پین ATSAME54P19A-AUT-EFP
| پین 1 | VDDIO — Digital I/O supply voltage (3.3V) |
| پین 2 | PA00 — GPIO PA00 / XIN32 |
| پین 3 | PA01 — GPIO PA01 / XOUT32 |
| پین 4 | PA02 — GPIO PA02 / AIN0 |
| پین 5 | PA03 — GPIO PA03 / AIN1 / VREFA |
| پین 6 | GND — Ground |
| پین 7 | PA04 — GPIO PA04 / AIN2 |
| پین 8 | PA05 — GPIO PA05 / AIN3 |
| پین 9 | PA06 — GPIO PA06 |
| پین 10 | PA07 — GPIO PA07 |
| پین 11 | PA08 — GPIO PA08 / I2C SDA |
| پین 12 | PA09 — GPIO PA09 / I2C SCL |
| پین 13 | PA10 — GPIO PA10 |
| پین 14 | PA11 — GPIO PA11 / USB DM |
| پین 15 | PA12 — GPIO PA12 / USB DP |
| پین 16 | PA13 — GPIO PA13 |
| پین 17 | PA14 — GPIO PA14 |
| پین 18 | PA15 — GPIO PA15 |
| پین 19 | PA16 — GPIO PA16 / SERCOM1 PAD0 |
| پین 20 | PA17 — GPIO PA17 / SERCOM1 PAD1 |
| پین 21 | PA18 — GPIO PA18 / SERCOM1 PAD2 |
| پین 22 | PA19 — GPIO PA19 / SERCOM1 PAD3 |
| پین 23 | PA20 — GPIO PA20 |
| پین 24 | PA21 — GPIO PA21 |
| پین 25 | PA22 — GPIO PA22 |
| پین 26 | PA23 — GPIO PA23 |
| پین 27 | PA24 — GPIO PA24 / USB SOF |
| پین 28 | PA25 — GPIO PA25 |
| پین 29 | PA26 — GPIO PA26 |
| پین 30 | PA27 — GPIO PA27 |
| پین 31 | PA28 — GPIO PA28 |
| پین 32 | PA29 — GPIO PA29 |
| پین 33 | PA30 — GPIO PA30 |
| پین 34 | PA31 — GPIO PA31 |
| پین 35 | GND — Ground |
| پین 36 | VDDIO — Digital I/O supply voltage (3.3V) |
| پین 37 | PB00 — GPIO PB00 |
| پین 38 | PB01 — GPIO PB01 |
| پین 39 | PB02 — GPIO PB02 / AIN4 |
| پین 40 | PB03 — GPIO PB03 / AIN5 |
| پین 41 | PB04 — GPIO PB04 / AIN6 |
| پین 42 | PB05 — GPIO PB05 / AIN7 |
| پین 43 | PB06 — GPIO PB06 |
| پین 44 | PB07 — GPIO PB07 |
| پین 45 | PB08 — GPIO PB08 |
| پین 46 | PB09 — GPIO PB09 |
| پین 47 | PB10 — GPIO PB10 |
| پین 48 | PB11 — GPIO PB11 |
| پین 49 | PB12 — GPIO PB12 |
| پین 50 | PB13 — GPIO PB13 |
| پین 51 | PB14 — GPIO PB14 |
| پین 52 | PB15 — GPIO PB15 |
| پین 53 | PB16 — GPIO PB16 |
| پین 54 | PB17 — GPIO PB17 |
| پین 55 | PB18 — GPIO PB18 |
| پین 56 | PB19 — GPIO PB19 |
| پین 57 | PB20 — GPIO PB20 |
| پین 58 | PB21 — GPIO PB21 |
| پین 59 | PB22 — GPIO PB22 |
| پین 60 | PB23 — GPIO PB23 |
| پین 61 | PB24 — GPIO PB24 |
| پین 62 | PB25 — GPIO PB25 |
| پین 63 | PB26 — GPIO PB26 |
| پین 64 | PB27 — GPIO PB27 |
| پین 65 | PB28 — GPIO PB28 |
| پین 66 | PB29 — GPIO PB29 |
| پین 67 | PB30 — GPIO PB30 |
| پین 68 | PB31 — GPIO PB31 |
| پین 69 | GND — Ground |
| پین 70 | VDDCORE — Core voltage (internal regulator output) |
| پین 71 | VDDIO — Digital I/O supply voltage (3.3V) |
| پین 72 | PC00 — GPIO PC00 |
| پین 73 | PC01 — GPIO PC01 |
| پین 74 | PC02 — GPIO PC02 |
| پین 75 | PC03 — GPIO PC03 |
| پین 76 | PC04 — GPIO PC04 |
| پین 77 | PC05 — GPIO PC05 |
| پین 78 | PC06 — GPIO PC06 |
| پین 79 | PC07 — GPIO PC07 |
| پین 80 | PC08 — GPIO PC08 |
| پین 81 | PC09 — GPIO PC09 |
| پین 82 | PC10 — GPIO PC10 |
| پین 83 | PC11 — GPIO PC11 |
| پین 84 | PC12 — GPIO PC12 |
| پین 85 | PC13 — GPIO PC13 |
| پین 86 | PC14 — GPIO PC14 |
| پین 87 | PC15 — GPIO PC15 |
| پین 88 | PC16 — GPIO PC16 |
| پین 89 | PC17 — GPIO PC17 |
| پین 90 | PC18 — GPIO PC18 |
| پین 91 | PC19 — GPIO PC19 |
| پین 92 | PC20 — GPIO PC20 |
| پین 93 | PC21 — GPIO PC21 |
| پین 94 | PC22 — GPIO PC22 |
| پین 95 | PC23 — GPIO PC23 |
| پین 96 | PC24 — GPIO PC24 |
| پین 97 | PC25 — GPIO PC25 |
| پین 98 | PC26 — GPIO PC26 |
| پین 99 | PC27 — GPIO PC27 |
| پین 100 | PC28 — GPIO PC28 |
| پین 101 | PC29 — GPIO PC29 |
| پین 102 | PC30 — GPIO PC30 |
| پین 103 | PC31 — GPIO PC31 |
| پین 104 | GND — Ground |
| پین 105 | VDDIO — Digital I/O supply voltage (3.3V) |
| پین 106 | PD00 — GPIO PD00 |
| پین 107 | PD01 — GPIO PD01 |
| پین 108 | PD02 — GPIO PD02 |
| پین 109 | PD03 — GPIO PD03 |
| پین 110 | PD04 — GPIO PD04 |
| پین 111 | PD05 — GPIO PD05 |
| پین 112 | PD06 — GPIO PD06 |
| پین 113 | PD07 — GPIO PD07 |
| پین 114 | PD08 — GPIO PD08 |
| پین 115 | PD09 — GPIO PD09 |
| پین 116 | PD10 — GPIO PD10 |
| پین 117 | PD11 — GPIO PD11 |
| پین 118 | PD12 — GPIO PD12 |
| پین 119 | NRST — External Reset (active-low) |
| پین 120 | SWDIO — Serial Wire Debug I/O |
| پین 121 | SWCLK — Serial Wire Debug Clock |
| پین 122 | VDDIO — Digital I/O supply voltage (3.3V) |
| پین 123 | GND — Ground |
| پین 124 | VDDCORE — Core voltage (internal regulator output) |
| پین 125 | VDDPLL — PLL analog supply |
| پین 126 | VDDUTMI — USB UTMI PHY supply (3.3V) |
| پین 127 | VBUS — USB VBUS detect input |
| پین 128 | GND — Ground |
کاربردهای معمول
ATSAME54P19A-AUT-EFP مناسب است برای 6 کاربردs: Industrial Gateway and Protocol Bridge, Automotive Telematics and OBD-II Gateway, Building Automation Controller (BACnet/Modbus), Smart Energy Metering with TLS Encryption, USB-C Powered Industrial HMI Touch Panel, Factory Automation PLC with EtherCAT SubDevice.
Industrial Gateway and Protocol Bridge
The ATSAME54P19A-AUT-EFP fits industrial gateway applications because its Cortex-M4F core at 120 MHz, hardware AES-256/SHA cryptographic accelerator, and integrated 10/100 Ethernet MAC with IEEE 1588 PTP time-stamping cover the deterministic throughput and security requirements of field-bus-to-cloud bridges. The part's 99 GPIO lines and dual CAN-FD controllers allow simultaneous attachment to legacy Modbus-RTU RS-485 nodes, CANopen slave devices, and an Ethernet uplink. Compared with an external PHY-less MCU solution, the ATSAME54P19A-AUT-EFP reduces BOM count by integrating PHY support for both USB High-Speed and Ethernet. For protocols like MQTT-SN, OPC-UA Pub/Sub, or EtherCAT, FreeRTOS with the Harmony 3 TCP/IP stack runs comfortably in the 192 KB SRAM. Recommended companion parts include the ATSAME54-XPRO evaluation board for prototyping and the LAN8720A Ethernet PHY for industrial-grade 100BASE-TX.
پیشنهادی
Automotive Telematics and OBD-II Gateway
For automotive telematics, the ATSAME54P19A-AUT-EFP combines the Cortex-M4F core's DSP/FPU capability with two CAN-FD controllers and USB High-Speed device mode, enabling real-time OBD-II diagnostics data acquisition, GPS sensor fusion, and cloud upload through a 4G modem. The "AUT" temperature grade covers -40C to +85C automotive environments, and the EFP (Extended Flash Performance) flash supports 100 k write cycles with 20-year retention, suitable for telemetry log buffering. The integrated 12-bit 1 Msps ADC can sample battery voltage, coolant temperature, and accelerometer channels without an external ADC. The hardware cryptographic accelerator offloads TLS 1.3 handshakes for secure OTA firmware updates. Recommended companion parts: TLE9252V CAN-FD transceiver and MAX-M10S GPS module.
پیشنهادی
Building Automation Controller (BACnet/Modbus)
The ATSAME54P19A-AUT-EFP is well matched to building automation controllers because its combination of dual CAN-FD, six SERCOM-configurable USART/I2C/SPI channels, and 12-bit ADC enables direct interfacing with BACnet MS/TP twisted-pair segments, Modbus RTU RS-485 nodes, and analog sensor inputs for temperature, humidity, and CO2. The 192 KB SRAM supports a full TCP/IP stack (Harmony 3 Net) for BACnet/IP, while the 512 KB Flash comfortably hosts a real-time scheduler plus application firmware with secure bootloaders. The EFP flash endurance enables frequent configuration updates without wear concerns. Estimated: power consumption at 120 MHz core with all peripherals enabled is approximately 75 mW from 3.3 V, manageable in DIN-rail enclosures with passive cooling. Recommended companion: ADM3485E RS-485 transceiver.
پیشنهادی
Smart Energy Metering with TLS Encryption
For smart energy metering, the ATSAME54P19A-AUT-EFP's hardware cryptographic accelerator (AES-256, SHA-256, TRNG) provides authenticated TLS 1.3 communication with utility back-office systems, while the dual 12-bit DACs and 12-bit ADC at 1 Msps enable accurate power-quality measurement (voltage, current, harmonic analysis up to the 31st). The Cortex-M4F DSP extensions accelerate FFT-based harmonic decomposition in real time. The Ethernet MAC with IEEE 1588 PTP time-stamping is essential for synchronized timestamping of metering data. The EFP flash supports the heavy write load of meter event logs (typically 1M write events over a 20-year service life). Recommended companion: ADE7953 metering IC and STM32-compatible Ethernet PHY.
پیشنهادی
USB-C Powered Industrial HMI Touch Panel
The ATSAME54P19A-AUT-EFP drives USB-C powered HMI panels because its USB 2.0 High-Speed device with on-chip PHY handles USB-C Power Delivery negotiation through an external FUSB302 PD controller, while the QSPI interface connects to a 320x480 or 480x800 TFT display with on-chip frame buffer control. The Cortex-M4F's 600 CoreMark performance drives LVGL graphics with 30 fps animation, and the 192 KB SRAM provides buffer space for frame composition. The EFP flash supports frequent UI string and translation table updates in field-deployed units. Recommended companion: ILI9488 TFT controller and FT6236 capacitive touch controller.
پیشنهادی
Factory Automation PLC with EtherCAT SubDevice
For factory automation PLCs running as EtherCAT sub-devices, the ATSAME54P19A-AUT-EFP provides the deterministic Cortex-M4F core for EtherCAT slave stack processing and the 192 KB SRAM to hold mailbox and process data buffers. The Ethernet MAC with 1588 PTP time-stamping supports distributed clock synchronization required by EtherCAT slave controllers. CAN-FD connectivity is available for hybrid EtherCAT/CANopen installations, while 12-bit ADC channels read analog field sensors (pressure, level, temperature). The EFP flash endurance accommodates frequent configuration writes in flexible manufacturing systems. Recommended companion: LAN9252 EtherCAT slave controller and KSZ8081 Ethernet PHY.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای ATSAME54P19A-AUT-EFP — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | ATSAME54P19A-AUT | ATSAME54P19A-AU-EFP | ATSAME54P20A-AUT | ATSAME54N20A-AUT | ATSAME54N19A-AUT | ATSAMD51P19A-AUT |
|---|---|---|---|---|---|---|---|
| Package | 128-TQFP (14x14 mm) | 128-TQFP (14x14 mm) - same | 128-TQFP (14x14 mm) - same | 128-TQFP (14x14 mm) - same | 128-TQFP (14x14 mm) - same | 128-TQFP (14x14 mm) - same | 128-TQFP (14x14 mm) - same |
| Brand | Microchip Technology | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same | Microchip Technology - same |
| Core | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz | Cortex-M4F @ 120 MHz |
| Flash Memory | 512 KB | 512 KB | 512 KB | 1 MB (+100%) | 1 MB (+100%) | 512 KB | 512 KB |
| SRAM | 192 KB | 192 KB | 192 KB | 256 KB (+33%) | 256 KB (+33%) | 192 KB | 192 KB |
| Flash Endurance | Extended (EFP, ~100k cycles) | Standard (no EFP) | Extended (EFP) | Standard | Standard | Standard | Standard |
| Temperature Grade | -40C to +85C (Automotive, AUT) | -40C to +85C (AUT) | -40C to +85C (Industrial, AU) | -40C to +85C (AUT) | -40C to +85C (AUT) | -40C to +85C (AUT) | -40C to +85C (AUT) |
| Packaging | Tape & Reel | Tape & Reel | Tray | Tape & Reel | Tape & Reel | Tape & Reel | Tape & Reel |
| Connectivity (Ethernet MAC) | Yes (10/100 with 1588 PTP) | Yes (10/100 with 1588 PTP) | Yes (10/100 with 1588 PTP) | Yes (10/100 with 1588 PTP) | Yes (10/100 with 1588 PTP) | Yes (10/100 with 1588 PTP) | No Ethernet (SAM D51 without MAC) |
تفاوت‌های کلیدی
- Extended Flash Performance with 100k cycle endurance (در مقابلATSAME54P19A-AUT (standard grade))
- Hardware cryptographic accelerator (AES/SHA/TRNG) (در مقابلATSAMD51P19A-AUT)
- 128 KB SRAM buffer for TCP/IP stacks (در مقابلATSAME54P20A-AUT (256 KB SRAM, 1 MB Flash))
یادداشت‌های طراحی
The ATSAME54P19A-AUT-EFP integrates an on-chip 1.2V core voltage regulator that derives VDDCORE from the 3.3V VDDIO supply. Place one 4.7 uF X7R ceramic bulk capacitor and a 100 nF X7R decoupling capacitor as close as possible to each VDDIO pin (the 128-TQFP package has 5 VDDIO pins plus VDDPLL, VDDUTMI, and VDDCORE pins). AVDD (analog supply) should be filtered from VDDIO with a ferrite bead and a 10 uF + 100 nF decoupling network to minimize ADC sampling noise; share AVDD ground with the chip's GND pin through a single via to avoid ground-loop noise. Estimated: at 120 MHz with all peripherals enabled, total 3.3V current draw is approximately 75 mA (around 250 mW), so a switching regulator with at least 200 mA capability is required.
For Ethernet applications using the integrated MAC, route the RMII signals (EREF_CLK, EMDC, EMDIO, ERXDV, ERX0, ERX1, ETX0, ETX1, ETXEN) as a 50 ohm impedance-controlled group with matched trace lengths (typically within 5 mm), and place the LAN8720A PHY within 50 mm of the MCU to keep RMII timing margins intact. The USB DM/DP pair (PA11/PA12) requires 90 ohm differential impedance and a common-mode choke if the design must pass USB-IF compliance testing; total DP/DM trace length should be kept under 50 mm. Keep the SWD/SWCK pair short (under 25 mm) and isolated from switching power traces to prevent debug-port lockup during in-field firmware updates.
Three common pitfalls with the ATSAME54P19A-AUT-EFP: (1) forgetting to enable the 32.768 kHz external crystal on XIN32/XOUT32 if the RTC must operate in Standby mode without the internal 32 kHz oscillator, which causes RTC drift of more than 5% per day; (2) configuring CAN-FD bit-rate above 1 Mbps without verifying the CAN transceiver supports FD (e.g. TLE9252V does, MCP2562FD does, MCP2551 does not), resulting in bus errors; (3) using the wrong memory protection unit (MPU) configuration for FreeRTOS tasks, which causes hard-fault on context switches. Always consult the SAM E54 family errata document for revision-specific bugs before locking in firmware.
Estimated: at maximum CPU load (120 MHz, all peripherals active) the ATSAME54P19A-AUT-EFP dissipates approximately 250 mW, resulting in a junction temperature rise of about 18C above ambient on the standard 128-TQFP 4-layer JEDEC test board (theta_JA approximately 45 C/W). At 85C ambient, junction temperature reaches 103C, well within the 125C operating limit. However, in a sealed enclosure with no airflow, de-rate by 10-15C. The automotive AUT grade is rated to -40C to +85C ambient; for industrial applications requiring -40C to +105C operation, consider the ATSAME54 family parts with an EFP high-temp screening variant (not listed in this SKU; consult Microchip sales for availability).
اطلاعات انطباق
RoHS compliant and lead-free per Microchip product page. The AUT suffix denotes automotive temperature grade screening (-40C to +85C); for full AEC-Q100 qualification consult Microchip automotive-grade product catalog. EFP flash variant provides automotive-grade endurance and retention.