Renesas Electronics

ICS581G-01 - 200MHz PLL Zero-Delay Clock Multiplexer | Renesas

MPN: ICS581G-01 ✓ فعال
16-TSSOP, 4.40 mm width, 0.65 mm pitch Package 200 MHz Speed
حداقل سفارش: 1 |

ICS581G-01 نمای کلی

The Renesas Electronics ICS581G-01 is a glitch-free, phase-locked-loop clock multiplexer with a maximum operating frequency of 200 MHz, two clock inputs, four true outputs, and zero input-to-output delay in a 16-pin TSSOP package. The device gives designers a zero-delay clock fanout function with user-controlled selection between the two input clocks.

A PLL-based clock multiplexer is a clock-and-timing integrated circuit that combines phase-locked-loop technology with clock selection or distribution. It belongs to the hierarchy of clock-and-timing ICs, where it serves as a specialized input-to-output clock distribution device. Unlike a conventional multiplexer that introduces propagation delay through logic gates, the ICS581G-01 uses a PLL to align its output phase with the selected reference clock.

The principal features include operation up to 200 MHz, four non-inverted clock outputs, and the ability to configure those outputs as one, three, or four active outputs. User-controlled mux switching distinguishes the ICS581G-01 from the automatically switching ICS581-02. According to the manufacturer datasheet, the architecture is designed to suppress output glitches while providing zero delay from input to output.

The PLL-based implementation supports predictable clock phase relationships across multiple loads when board layout, power distribution, and output configuration are handled correctly. Each of the four outputs can be enabled as part of a one-output, three-output, or four-output arrangement. This flexibility allows the same device to serve as a one-to-four clock fanout element, a two-input clock selector, or a redundant-clock transition component.

Typical uses include processor and FPGA clock distribution, memory-clock fanout, network-interface clocking, telecommunications equipment, industrial control systems, and test-and-measurement platforms. The 200 MHz upper operating frequency makes the device suitable for systems whose clock architecture benefits from phase-aligned outputs rather than conventional buffered propagation delay.

PCB implementation should use short, impedance-controlled clock traces, solid ground-plane continuity, and decoupling close to the supply pins. The TSSOP-16 package requires careful fanout because four outputs must reach separate destinations without introducing avoidable skew. Input and output timing should be evaluated together with loading, trace length, and the switching method used by the downstream logic.

This page consolidates the device function, verified electrical and package characteristics, practical clock-tree design notes, and qualified drop-in alternatives. It also distinguishes the user-controlled ICS581G-01 from related suffix variants so engineers can assess timing, temperature, packaging, and lifecycle requirements before approving a substitution.

جایگزین‌های drop-in برای ICS581G-01 — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

ICS581G-01IT

✅ جایگزین مستقیم
📦 TSSOP-16
Same 200 MHz function and 16-TSSOP footprint; the -IT ordering suffix differs in temperature or ordering treatment by 0% in the listed core frequency and function.

📋 جایگزین مرجع (خارج از کاتالوگ)

ICS581G-01LF

✅ جایگزین مستقیم
📦 TSSOP-16
Same 200 MHz zero-delay clock-multiplexer function and 16-TSSOP footprint; the -LF suffix differs in lead-free ordering treatment with 0% listed core-parameter difference.

📋 جایگزین مرجع (خارج از کاتالوگ)

581G-01I

✅ جایگزین مستقیم
📦 TSSOP-16
Same 581-series 200 MHz PLL-based, four-true-output TSSOP-16 architecture; the -I suffix differs by 0% in the listed core frequency and output configuration.

📋 جایگزین مرجع (خارج از کاتالوگ)

ICS581G-01 مشخصات

Device Type Fanout Distribution, Multiplexer, Zero Delay Buffer IC
Maximum Frequency 200 MHz
Number of Circuits 1 circuit
Input-to-Output Ratio 2 inputs to 4 outputs
PLL Yes, phase-locked-loop based
Clock Input Type Clock
Clock Output Type Clock
Input Delay 0 ns
Output Count 4 true outputs
Inverted Output Count 0 inverted outputs
پیکربندی خروجی 1, 3, or 4 outputs
Mux Switching User controlled
Switching Behavior Glitch free
بسته‌بندی 16-TSSOP, 4.40 mm width, 0.65 mm pitch
وضعیت RoHS Compliant

راهنمای پیکربندی پین ICS581G-01 16-tssop, 4.40 mm width, 0.65 mm pitch

پیکربندی پین برای ICS581G-01 (پکیج 16-tssop, 4.40 mm width, 0.65 mm pitch). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 16-tssop, 4.40 mm width, 0.65 mm pitch برای ICS581G-01

داده پین‌آوت تفصیلی موجود نیست برای ICS581G-01.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

ICS581G-01 مناسب است برای 6 کاربردs: FPGA Clock Fanout, Processor Clock Distribution, Telecommunications Equipment, Industrial Control Systems, Test and Measurement Instrumentation, Memory and Interface Clocking.

🖥️

FPGA Clock Fanout

The ICS581G-01 fits FPGA clock trees requiring one of two reference clocks to be distributed to as many as four destinations. Its PLL-based architecture provides zero nominal input-to-output delay, while the four true outputs can be configured individually for one-, three-, or four-output operation. According to the manufacturer datasheet, maximum operating frequency is 200 MHz, making source selection and output-enable behavior suitable for FPGA migration and redundant-clock systems. The primary design consideration is board-level skew: route each output over a continuous reference plane, match lengths where timing closure requires it, and avoid test pads or stubs near the clock nets.

⚡

Processor Clock Distribution

The ICS581G-01 can distribute a selected processor reference clock to multiple clock domains without the nominal propagation delay of gate-based fanout logic. It supports two clock inputs and four true outputs up to 200 MHz, allowing a system to switch between a primary oscillator and an alternate reference under controlled conditions. According to the manufacturer datasheet, the PLL-based multiplexer is designed for glitch-free operation and zero input-to-output delay. Use it where source selection is deliberate rather than automatic, and validate output enable timing, package skew, and power-return continuity in the final processor clock domain.

🌐

Telecommunications Equipment

ICS581G-01 is applicable to telecommunications and network equipment that needs phase-aligned clocks delivered to several functional blocks. The two input channels permit deliberate selection between reference sources, while four low-skew outputs support a one-to-four fanout arrangement. According to the Renesas Electronics manufacturer datasheet, the PLL-based multiplexer operates up to 200 MHz and provides glitch-free, zero-delay transfer from the selected input. In a line-card design, keep clock routing away from noisy switching-converter regions, use a continuous ground reference, and confirm that each enabled output maintains the intended phase relationship at its destination.

🏭

Industrial Control Systems

The ICS581G-01 can provide synchronized clock distribution for industrial controllers, data-conversion equipment, and multi-channel measurement systems. Its four configurable true outputs let one selected reference feed several subsystems, while the maximum 200 MHz operating frequency covers communication and control-clock requirements. According to the manufacturer datasheet, the device supports user-controlled selection between two clocks and maintains a zero-delay PLL-based path. Engineers should account for temperature-grade suffix requirements, provide stable local decoupling, and use output-enable sequencing appropriate to the controlled system rather than relying on uncontrolled source changes during operation.

🔧

Test and Measurement Instrumentation

The ICS581G-01 is suitable for laboratory and test systems requiring a selectable reference clock distributed with consistent phase relationships. Four low-skew outputs can feed ADC, DAC, counter, or capture sections, and the zero-delay architecture helps simplify timing relationships around the selected source. According to the manufacturer datasheet, the device supports 200 MHz operation, two inputs, and four true outputs. Place the multiplexer close to the common clock origin, use matched routing where multiple instrument channels must remain synchronized, and verify source-switch commands against the downstream acquisition timing budget.

🔧

Memory and Interface Clocking

ICS581G-01 can serve memory or high-speed interface subsystems that require a selected clock to reach multiple loads with low added delay. The device supports two source inputs and four true outputs up to 200 MHz, making it useful where one source must feed parallel interface blocks or where a controlled transition between clock domains is required. According to the manufacturer datasheet, the PLL-based design provides zero nominal input-to-output delay and glitch-free switching. Layout should minimize output-to-load distance, preserve a continuous reference plane, and account for the datasheet timing budget across every enabled output and package transition.

خلاصه محصولات پیشنهادی

ICS581G-01IT Suffix-specific 16-TSSOP drop-in candidate for FPGA clock trees استفاده‌شده در: FPGA Clock Fanout, Processor Clock Distribution, Telecommunications Equipment, Industrial Control Systems, Test and Measurement Instrumentation, Memory and Interface Clocking ICS581G-01LF Lead-free-ordering 16-TSSOP candidate for the same clock architecture استفاده‌شده در: FPGA Clock Fanout, Telecommunications Equipment, Test and Measurement Instrumentation 581G-01I Same-family TSSOP-16 clock distribution candidate استفاده‌شده در: Processor Clock Distribution, Industrial Control Systems, Memory and Interface Clocking
What is the ICS581G-01?
The ICS581G-01 is a glitch-free, PLL-based zero-delay clock multiplexer rated to 200 MHz. According to the Renesas Electronics manufacturer datasheet, it accepts two clock inputs, provides four true outputs, and supports user-controlled mux switching. The device is packaged in a 16-TSSOP package and can be configured for one, three, or four active outputs.
What are the key specifications of ICS581G-01 that engineers should know?
The ICS581G-01 combines a 200 MHz maximum operating frequency, two clock inputs, four true outputs, and zero input-to-output delay. According to the Renesas Electronics manufacturer datasheet, the PLL-based circuit is designed for glitch-free operation, while user-controlled switching allows selection between the two reference clocks. Its 16-TSSOP package uses a 4.40 mm body width and 0.65 mm pitch.
How many inputs and outputs does ICS581G-01 have?
The ICS581G-01 has two clock inputs and four true clock outputs, with no inverted outputs. According to the Renesas Electronics manufacturer datasheet, the four outputs may be configured as a single output, three outputs, or four outputs. This provides a configurable one-to-four fanout arrangement while preserving a zero-delay PLL-based signal path.
Is ICS581G-01 suitable for FPGA clock distribution?
Yes, the ICS581G-01 is suitable for FPGA clock distribution when phase alignment and low added delay are important. Its PLL-based architecture provides zero nominal input-to-output delay, and its four outputs can feed multiple destinations from one selected reference clock. According to the manufacturer datasheet, maximum operating frequency is 200 MHz, making system-level trace, load, and timing analysis essential.
What is the difference between ICS581G-01 and ICS581-02?
The primary difference is switching control: ICS581G-01 allows the user to control mux switching, while ICS581-02 automatically switches between its two clock inputs. According to the Renesas Electronics manufacturer datasheet, both are glitch-free, PLL-based clock multiplexers with four low-skew outputs and zero input-to-output delay. The selection therefore depends on whether manual clock selection or automatic transition is required.
Can ICS581G-01IT replace ICS581G-01?
ICS581G-01IT can be a candidate replacement because it is listed with the same 200 MHz fanout, multiplexing, zero-delay-buffer function and 16-TSSOP package. However, the -IT suffix may identify a different ordering or temperature treatment, so procurement and qualification records must be compared before installation. According to the Renesas Electronics manufacturer datasheet, the base ICS581-01 supports user-controlled switching.
What is the best drop-in replacement for ICS581G-01?
ICS581G-01IT is the closest documented drop-in candidate because it retains the same 200 MHz PLL clock-multiplexer function and 16-TSSOP footprint. The manufacturer datasheet should be used to verify temperature grade, ordering suffix, enable logic, and lifecycle status before substitution. Use the Request a Quote form on this page to confirm the exact suffix and current sourcing conditions.
What Renesas equivalent can replace ICS581G-01?
ICS581G-01IT is the closest listed Renesas equivalent because it uses the same 16-TSSOP package and retains the 200 MHz zero-delay clock-multiplexer function. No cross-brand pin-to-pin equivalent is established by the available technical records. According to the manufacturer datasheet, engineers should also verify the suffix-specific temperature and ordering requirements before approving a replacement.
Where can I download the ICS581G-01 datasheet PDF?
The ICS581G-01 datasheet PDF is available through the product-document link on this page, with the original manufacturer document also indexed by the ICS581-01 family. According to the Renesas Electronics manufacturer datasheet, the document describes the glitch-free PLL-based multiplexer, four configurable outputs, zero delay, and user-controlled switching. Use the document’s pin-description table when assigning PCB tracks.
Where can I find the ICS581G-01 pinout?
Use the pin-description table in the ICS581-01 family manufacturer datasheet to locate every TSSOP-16 connection and verify the exposed power and ground pins. The verified product record identifies a 16-TSSOP package but does not reproduce the complete pin-name table. According to the manufacturer datasheet, the device has two clock inputs and four true outputs, with configuration logic controlling the available output arrangement.
How should clock traces be routed for ICS581G-01?
Route clock inputs and outputs on short, continuous paths with a solid reference plane and avoid introducing stubs or unnecessary layer changes. The four outputs should be length-matched when their destinations require minimized skew. According to the Renesas Electronics manufacturer datasheet, the device provides low-skew true outputs, but package and PCB propagation effects remain part of the final system timing budget.
Does ICS581G-01 need external clock multiplexing logic?
No separate logic multiplexer is required when the system can use the ICS581G-01’s integrated PLL-based clock selection function. According to the Renesas Electronics manufacturer datasheet, the device includes two clock inputs, four low-skew outputs, zero delay, and user-controlled switching. External control logic is still needed to issue switching commands if the host system requires software-managed source selection.
Is ICS581G-01 in stock and what is its lead time?
Current stock and lead time should be requested through the Request a Quote form on this page so the exact ordering suffix, quantity, and delivery requirements can be confirmed. According to the Renesas Electronics manufacturer datasheet, the ICS581G-01 is the standard 16-TSSOP user-switching version, while suffix-specific conditions such as temperature grade may affect availability.
What is the price of ICS581G-01?
Use the Request a Quote form on this page for current pricing, quantity availability, and lead-time confirmation for the exact ICS581G-01 ordering suffix. According to the Renesas Electronics manufacturer datasheet, the device is a 200 MHz PLL-based zero-delay clock multiplexer in a 16-TSSOP package, so its price must be matched to the package and suffix required by the design.
How does ICS581G-01 affect board-level clock skew?
The ICS581G-01 provides four low-skew true outputs from its PLL-based architecture, helping maintain controlled relationships between distributed clocks. According to the Renesas Electronics manufacturer datasheet, the device has zero input-to-output delay and supports four-output operation. Actual board skew still depends on trace length, loading, output enable state, reference-clock quality, and power-return paths.
When should I choose ICS581G-01 over an automatic-switching clock multiplexer?
Choose ICS581G-01 when system firmware or hardware control must explicitly select one of two clock sources. According to the Renesas Electronics manufacturer datasheet, the ICS581G-01 provides user-controlled switching, whereas ICS581-02 performs automatic switching. ICS581G-01 is therefore better for deliberate source arbitration, while automatic switching is preferable when continuity must transition without a host command.

داده‌های مرجع مهندسی برای ICS581G-01 — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose ICS581G-01 when the design needs explicit, user-controlled selection between two clock sources and a zero-delay, PLL-based path with four true outputs. It is particularly useful in FPGA, processor, telecommunications, industrial-control, and instrumentation clock trees operating up to 200 MHz. Select ICS581G-01IT when its documented ordering and temperature treatment satisfy the production requirements; select ICS581G-01LF when its lead-free ordering designation is required; consider 581G-01I when that specific suffix matches the qualified BOM configuration. Before any substitution, compare pin names, enable polarity, temperature range, output configuration, lifecycle status, and ordering code against the manufacturer datasheet. For systems that must switch sources automatically, the ICS581-02 family is functionally more appropriate, but it is not listed here as a drop-in alternative because automatic and user-controlled switching are distinct operating requirements.

مقایسه با جایگزین‌ها

پارامتر این محصول ICS581G-01IT ICS581G-01LF 581G-01I
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Package TSSOP-16 TSSOP-16 TSSOP-16 TSSOP-16
Device Type Fanout Distribution, Multiplexer, Zero Delay Buffer IC Fanout Distribution, Multiplexer, Zero Delay Buffer IC Zero-Delay Glitch-Free Clock Multiplexer PLL Based Clock Driver
PLL Based Yes Yes Yes Yes
True Outputs 4 4 4 4
Inverted Outputs 0 0 0 0
Input-to-Output Delay 0 ns 0 ns 0 ns 0 ns

تفاوت‌های کلیدی

  • Manual source selection (در مقابلICS581-02)
  • Four configurable true outputs (در مقابلICS581G-01IT)
  • Zero-delay PLL clock path (در مقابلICS581G-01LF)

یادداشت‌های طراحی

Place ICS581G-01 close to the common clock origin and route each output over a continuous ground or power reference plane. Avoid stubs, test pads, and unnecessary layer transitions on high-speed clock nets. When all four outputs must have closely matched arrival times, use the pin-description table in the manufacturer datasheet and PCB propagation data to establish acceptable trace-length differences.

Evaluate input slew rate, source impedance, output loading, and the enabled-output configuration as one timing system. The device's stated zero-delay architecture refers to its nominal input-to-output path and does not remove package or PCB propagation effects. Keep clock sources and destinations on quiet layers, and verify the complete timing budget at each load rather than relying on frequency capability alone.

Use a quiet supply path with local decoupling placed as close as practical to the device power and ground pins. Separate or shape clock-return current so switching currents from external loads do not modulate the reference used by the PLL. Confirm the operating voltage, supply-current limits, and decoupling recommendations directly in the manufacturer datasheet before releasing the PCB layout.

Do not treat the ICS581G-01 and automatic-switching ICS581-02 as interchangeable control functions, even though both share the PLL-based clock-multiplexer concept. The ICS581G-01 uses user-controlled mux switching, so firmware or external logic must issue the intended selection command. Also confirm the ordering suffix and temperature grade when replacing ICS581G-01 with ICS581G-01IT, ICS581G-01LF, or 581G-01I.

اطلاعات انطباق

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The verified technical record identifies the ICS581G-01 as RoHS compliant. Additional environmental and material-compliance declarations are not established by the cited records.

تاریخ تأیید داده‌ها: 2026-11-16 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

ICS581G-01 datasheet ICS581G-01 pinout ICS581G-01 datasheet pdf ICS581G-01 200MHz clock multiplexer ICS581G-01 TSSOP-16 ICS581G-01 zero delay buffer ICS581G-01 FPGA clock fanout ICS581G-01 equivalent ICS581G-01 replacement ICS581G-01 cross reference ICS581G-01 vs ICS581G-01IT ICS581G-01 price ICS581G-01 stock Renesas ICS581G-01

قطعات و اصطلاحات مرتبط

Renesas Electronics ICS581G-01 ICS581G-01IT ICS581G-01LF 581G-01I ICS581-02 PLL-based clock multiplexer zero-delay buffer clock fanout clock distribution phase-locked loop integrated circuit clock and timing IC semiconductor TSSOP-16 surface-mount package RoHS glitch-free switching input-to-output delay true output low-skew clock FPGA clock tree industrial control
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ