LM2904F-E2 - Dual Ground-Sense Op Amp, 3-32V | ROHM Semiconductor
MPN: LM2904F-E2 ✗ پایان تولیدLM2904F-E2 نمای کلی
A ground-sense operational amplifier is an op-amp configuration designed to measure or amplify small voltage signals referenced to ground, especially signals whose lower operating range is close to 0V. The LM2904 family combines two amplifiers in one package, allowing each channel to be used independently for signal conditioning, buffering, or low-level voltage amplification. Its wide supply-voltage range allows operation from 3V single-supply systems through higher-voltage industrial control and instrumentation circuits.
The verified product information identifies the LM2904F-E2 as a standard general-purpose amplifier with two circuits, an 8-SOP package, and a 3V to 32V operating supply range. ROHM's product page also identifies the device as a ground-sense operational amplifier and states that it cannot be used for new designs. The -E2 suffix denotes the manufacturer's ordering or packaging designation, while the F variant identifies the ground-sense amplifier family.
Typical uses include current-sense signal conditioning, sensor-interface circuits, low-voltage control systems, and instrumentation in which the input signal can approach the negative supply rail. The dual configuration can reduce board area when two related analog channels are required. The 8-pin SOP package is also compatible with conventional through-hole and leaded assembly processes, although current designs should confirm the availability and lifecycle status of the exact suffix before committing a new production release.
Designers should review the manufacturer datasheet for the complete electrical limits, input common-mode behavior, output swing, bias-current specifications, noise values, compensation stability, and recommended decoupling. A stable bypass capacitor should be placed close to the supply pins, and unused input channels should be handled according to the datasheet's recommended configuration. Because the manufacturer does not recommend this part for new designs, engineers should normally evaluate a current recommended dual operational amplifier with the same 8-pin footprint and equivalent electrical performance.
This page combines the manufacturer product information, distributor identification, lifecycle notice, package data, and practical engineering guidance for engineers evaluating the LM2904F-E2 or searching for a compatible replacement.
جایگزین‌های drop-in برای LM2904F-E2 — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای LM2904F-E2 (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Mounting Type, Amplifier Type, Number of Channels, Input Offset Voltage.
LM2904F
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
LM2904DR
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM2904BIDR
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM2904LV
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
LM2904P3
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM2904F-E2 حداکثر مقادیر مجاز و مشخصات الکتریکی
| Amplifier Type | Dual ground-sense operational amplifier |
| Number of Circuits | 2 circuits |
| Operating Supply Voltage Range | 3V to 32V |
| بسته‌بندی | 8-pin SOP |
| Product Classification | Standard general-purpose amplifier |
| Lifecycle Recommendation | Not recommended for new designs |
| Design Diversion Status | Not recommended for design diversion |
| نوع نصب | Surface mount, 8-pin SOP |
راهنمای پیکربندی پین LM2904F-E2 8-pin sop
پیکربندی پین برای LM2904F-E2 (پکیج 8-pin sop). این قطعه آنالوگ دارای پین‌های ورودی، خروجی و تغذیه است. برای پیکربندی‌های پین offset null، جبران‌سازی و فعال‌سازی به دیتاشیت سازنده مراجعه کنید. ایده‌آل برای مدارهای شرطی‌سازی سیگنال و تقویت‌کننده.
داده پین‌آوت تفصیلی موجود نیست برای LM2904F-E2.
به دیتاشیت برای پیکربندی کامل پین‌ها.
کاربردهای معمول
LM2904F-E2 مناسب است برای 6 کاربردs: Current-Sense Signal Conditioning, Low-Voltage Sensor Interface, Industrial Control Signal Amplification, Battery and Portable Monitoring, Audio and Instrumentation Buffering, Power-Supply Feedback and Monitoring.
Current-Sense Signal Conditioning
The LM2904F-E2 is suitable for amplifying the small voltage produced by a low-value current-sense resistor when the signal is referenced near ground. Its ground-sense architecture is relevant to battery, motor, and industrial control circuits where the measured voltage can remain close to the lower rail. Place the amplifier in the appropriate non-inverting or inverting topology, maintain the input within the datasheet common-mode range, and check offset voltage against the resolution required by the measurement. The 3V-to-32V supply range permits operation across low-voltage and higher-voltage instrumentation systems.
پیشنهادی
Low-Voltage Sensor Interface
Use the LM2904F-E2 when a sensor produces a millivolt-level output close to ground and requires amplification before conversion or control processing. The ground-sense characteristic helps preserve signal information near the lower supply rail, while the dual-circuit package allows two related sensor channels to share one package. Check the sensor output range, input bias current, offset voltage, and noise requirements against the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and the feedback network should be designed for the intended closed-loop gain.
پیشنهادی
Industrial Control Signal Amplification
The LM2904F-E2 can amplify low-level control or feedback signals in industrial systems whose analog node is close to ground. The 3V-to-32V operating supply range supports a broad range of control-board supply conditions, while the two independent channels can handle related measurements. The device is not recommended for new designs, so engineers should use it for qualified legacy maintenance or evaluate a current recommended amplifier for new control platforms. Confirm the operating-temperature range, output swing, capacitive-load behavior, and electromagnetic robustness in the datasheet and system qualification plan.
پیشنهادی
Battery and Portable Monitoring
The LM2904F-E2 can condition voltage-divided battery-monitoring signals when the measured level approaches the ground rail. Its low-side signal capability makes it relevant to portable equipment, battery-management boards, and energy-monitoring systems that use a resistive divider or shunt. The 3V minimum supply is useful for compact systems, but the exact quiescent current and operating-temperature limits must be checked before power-budget approval. For new portable products, verify current recommended alternatives because the manufacturer has designated LM2904F-E2 as not recommended for new designs.
پیشنهادی
Audio and Instrumentation Buffering
The LM2904F-E2 can serve as a general-purpose amplifier or buffer in instrumentation where the signal level is small and the reference is ground-centered. The dual amplifier arrangement can reduce the number of packages when two channels require similar conditioning. However, the verified product information does not specify noise, bandwidth, slew rate, or output swing, so audio or precision-instrumentation designs should compare those parameters directly against the manufacturer datasheet. Check stability with the intended source and load capacitances and verify that the selected replacement improves noise rather than only matching the package.
پیشنهادی
Power-Supply Feedback and Monitoring
The LM2904F-E2 can be used to amplify a feedback or monitoring voltage in a power-conversion system, particularly when the signal is close to ground and the amplifier must operate from a single supply. The 3V-to-32V supply range provides flexibility across control and auxiliary rails. Because the exact output swing, input common-mode limits, and quiescent current are not stated in the product-page excerpt, verify those values before using the device in a feedback loop. Add local supply bypassing and keep the feedback trace away from high-current switching paths.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای LM2904F-E2 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | LM2904F | LM2904 | LM2904B | LM2904LV | LM2904P3 |
|---|---|---|---|---|---|---|
| Package | 8-pin SOP | 8-pin SOP - same package family | 8-pin SOIC - equivalent leaded footprint family | 8-pin SOIC - equivalent leaded footprint family | 8-pin SOIC - equivalent leaded footprint family | 8-pin SOIC - equivalent leaded footprint family |
| Brand | ROHM Semiconductor | ROHM Semiconductor | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Configuration | Dual | Dual | Dual | Dual | Dual | Dual |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
تفاوت‌های کلیدی
- Ground-sense positioning (در مقابلLM2904P3)
- Wide single-supply operating range (در مقابلLM2904B)
- Dual-channel integration (در مقابلLM2904)
- Legacy-product status (در مقابلLM2904F)
یادداشت‌های طراحی
Do not treat the 3V-to-32V supply rating as permission to ignore the input common-mode or output-swing limits. The ground-sense feature is valuable only when the signal remains inside the amplifier's valid input and output ranges. Before making a substitution, compare the original device's offset voltage, bias current, common-mode range, output swing, noise, bandwidth, and stability limits with the candidate datasheet.
Place the supply bypass capacitor as close as practical to the device's supply pins and ground connection. Keep the feedback and input traces short, particularly when the amplifier drives a capacitive or high-impedance load. Use a solid ground-plane connection and keep analog input routing away from switching nodes and high-current return paths to reduce ground disturbance in low-level signal-conditioning circuits.
The LM2904F-E2 is intended for low-current general-purpose signal conditioning, but the exact quiescent current and output-drive limits are not stated in the verified product excerpt. Verify the datasheet values against the system's power budget and output-load requirements. For battery-powered designs, calculate the supply current at both standby and operating states and include the effect of the external feedback network.
The 8-pin SOP package provides limited thermal dissipation compared with larger power packages. Check the operating ambient temperature, maximum input-output voltage difference, load current, and the manufacturer's thermal information before using the amplifier in a continuously loaded or high-voltage condition. For new designs, verify the replacement's thermal resistance and package land pattern rather than assuming that an 8-pin outline is interchangeable.
اطلاعات انطباق
The verified manufacturer and distributor excerpts do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. The manufacturer states that LM2904F-E2 is not recommended for new designs and not recommended for design diversion.
