LPC1112JHN33/203E - 50MHz 16KB Flash MCU | NXP
MPN: LPC1112JHN33/203E ✓ فعالLPC1112JHN33/203E نمای کلی
A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, volatile data memory, and peripherals into one package. The Cortex-M0 core uses a compact instruction set intended to replace conventional 8-bit and 16-bit controllers in cost-sensitive embedded products. In the LPC11xx family hierarchy, this device belongs to the ARM Cortex-M0 microcontroller, embedded-controller, and semiconductor categories.
Key features include a maximum CPU frequency of 50 MHz, 16 KB of Flash program memory, and 4 KB of SRAM. The integrated peripheral set includes an 8-channel 10-bit ADC, I2C, SPI, UART/USART, brown-out detection, and timer resources. These functions allow the LPC1112JHN33/203E to control sensors, communicate with external converters, and manage digital actuators without requiring several discrete interface components.
The 32-bit Cortex-M0 architecture supports efficient exception handling and structured firmware development while maintaining a compact software footprint. Its 3.3 V to 3.6 V operating supply range suits conventional industrial, consumer, and embedded-control systems that use a regulated 3.3 V rail. The HVQFN-32 surface-mount package also supports compact PCB construction, although its exposed thermal pad and fine lead pitch require careful assembly planning.
Typical uses include building automation controllers, portable instrumentation, compact sensor hubs, motor and relay control, and industrial serial gateways. The device is particularly useful when a design needs several communication interfaces, mixed-signal measurement, and moderate processing performance without the memory demands of a larger microcontroller.
PCB design should preserve thermal and electrical access to the exposed pad, place decoupling capacitors close to the supply pins, and route sensitive analog inputs away from switching nodes. Firmware must also account for the limited 4 KB SRAM and 16 KB Flash budgets when scheduling interrupts, buffering samples, and maintaining protocol stacks.
جایگزینهای drop-in برای LPC1112JHN33/203E — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
LPC1111JHN33/203E
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
LPC1113JHN33/203E
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
LPC1114JHN33/203E
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
LPC1112JHN33/203E حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | 32-bit ARM Cortex-M0 microcontroller |
| CPU Core | ARM Cortex-M0 |
| Maximum CPU Frequency | 50 MHz |
| Flash Program Memory | 16 KB |
| SRAM | 4 KB |
| ولتاژ تغذیه کاری | 3.3 V to 3.6 V |
| ADC Resolution | 10 bits |
| ADC Channels | 8 channels |
| Serial Interfaces | I2C, SPI, and UART/USART |
| Brown-Out Detection | Yes |
| Architecture | 32-bit RISC |
| بستهبندی | 32-HVQFN, 7 mm x 7 mm |
| نوع نصب | Surface mount |
| تعداد پینها | 32 pins |
راهنمای پیکربندی پین LPC1112JHN33/203E 32-hvqfn, 7 mm x 7 mm
پیکربندی پین برای LPC1112JHN33/203E (پکیج 32-hvqfn, 7 mm x 7 mm). این IC دیجیتال شامل GPIO، رابطهای ارتباطی (UART، SPI، I2C) و پینهای تغذیه است. برای عملکردهای جایگزین پین و گزینههای پیکربندی به دیتاشیت سازنده مراجعه کنید. ضروری برای طراحی سیستمهای نهفته و چیدمان PCB.
داده پینآوت تفصیلی موجود نیست برای LPC1112JHN33/203E.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
LPC1112JHN33/203E مناسب است برای 6 کاربردs: Industrial Sensor Hub, Building Automation Controller, Portable Instrumentation, Motor and Relay Control, Compact Serial Gateway, Embedded Data Acquisition.
Industrial Sensor Hub
The LPC1112JHN33/203E fits compact sensor-hub designs that combine analog measurements with local serial processing. Its 8-channel 10-bit ADC provides a practical interface for pressure, temperature, and level sensors, while the 50 MHz Cortex-M0 core can filter samples and format data for a host controller. I2C and SPI support temperature sensors, flash devices, and digital sensor modules, while UART/USART provides a simple industrial service interface. The main constraint is the 4 KB SRAM, which requires bounded sample buffers and careful allocation by the firmware.
پیشنهادی
Building Automation Controller
The LPC1112JHN33/203E is well suited to compact building-automation nodes that monitor environmental inputs and operate relays or actuators. Its Cortex-M0 processor provides enough control capability for scheduling and protocol handling, while the ADC can read resistive sensing elements through an appropriate conditioning circuit. UART/USART supports a local service console, and I2C or SPI can connect display, memory, or sensor modules. Firmware should use timer-based scheduling and event-driven peripheral access to preserve CPU time and SRAM availability.
پیشنهادی
Portable Instrumentation
The LPC1112JHN33/203E supports portable measurement instruments where component count, package area, and power efficiency are important. A 50 MHz ARM Cortex-M0 core can execute measurement control, calibration logic, and display updates, while the integrated 10-bit ADC handles suitable low-frequency or moderate-resolution analog channels. The 3.3 V to 3.6 V operating range integrates with common low-voltage analog sections. Brown-out detection improves behavior during battery or supply transitions, although the complete design must include a regulator suitable for the instrument's current demand.
پیشنهادی
Motor and Relay Control
The LPC1112JHN33/203E can act as the low-voltage controller in a motor, relay, or solenoid management module. Its timer resources support deterministic switching sequences, and its GPIO can operate driver-enable inputs, fault signals, and status indicators. The 32-HVQFN package preserves PCB area in compact control modules, while I2C and SPI permit connection to position sensors, power monitors, or driver ICs. A 10-bit ADC can supervise supply or current feedback when the external analog front end provides a suitable voltage range.
پیشنهادی
Compact Serial Gateway
The LPC1112JHN33/203E can bridge local serial devices through a compact industrial gateway or protocol-conversion node. UART/USART, I2C, and SPI provide several communication paths, and the 50 MHz Cortex-M0 core is sufficient for framing, buffering, and basic protocol translation. Brown-out detection supports more predictable recovery during rail disturbances. Designers should avoid simultaneously enabling high-throughput interfaces if the 4 KB SRAM cannot accommodate the required buffers, and should use a time-based scheduler rather than blocking routines for serial traffic.
پیشنهادی
Embedded Data Acquisition
The LPC1112JHN33/203E is appropriate for small data-acquisition systems that sample several analog channels and transfer results through a serial link. Its 8-channel 10-bit ADC supports monitoring applications, and the 16 KB Flash provides space for control code, calibration tables, and a compact bootloader. The core can handle filtering and timestamp management at up to 50 MHz. Practical designs should establish acquisition timing with a hardware timer, use double buffering when possible, and verify that peak processing and communication rates do not exceed the available SRAM.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای LPC1112JHN33/203E — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | LPC1111JHN33/203E | LPC1113JHN33/203E | LPC1114JHN33/203E |
|---|---|---|---|---|
| Package | 32-HVQFN, 7 mm x 7 mm | 32-HVQFN, 7 mm x 7 mm | 32-HVQFN, 7 mm x 7 mm | 32-HVQFN, 7 mm x 7 mm |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| CPU Core | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 | ARM Cortex-M0 |
| Maximum CPU Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
تفاوتهای کلیدی
- Provides 16 KB of Flash for a larger firmware working set (در مقابلLPC1111JHN33/203E)
- Maintains the same core speed and package as larger family members (در مقابلLPC1114JHN33/203E)
- Combines mixed-signal measurement with multiple serial interfaces (در مقابلLPC1113JHN33/203E)
یادداشتهای طراحی
Treat the HVQFN-32 footprint as a fine-pitch assembly constraint. Follow the exact NXP land pattern, including the exposed thermal pad, and confirm the PCB pad dimensions and solder-mask opening against the package drawing. Route every ground connection to the exposed pad and ground pins according to the recommended layout, while keeping analog inputs and crystal or clock traces away from high-current switching paths.
Place the required bypass capacitors close to the device supply and ground pins, with short return paths that do not share high-current switching loops with sensitive signals. The LPC1112JHN33/203E operates from 3.3 V to 3.6 V, so the regulator must maintain this range during transient loading. Brown-out detection can flag an undervoltage condition, but it does not replace correct power-supply design or local decoupling.
Do not treat a same-footprint LPC11xx device as a firmware-identical substitution. Flash and SRAM capacities can differ across the family, and a migration can require linker, startup, boot, and peripheral-configuration changes. Confirm the complete ordering suffix, pin table, memory sizes, clock limits, and brown-out behavior against the official datasheet for each candidate before approving a drop-in replacement.
اطلاعات انطباق
No explicit compliance declarations were identified for the complete LPC1112JHN33/203E ordering code.