Analog Devices

LT1037CJ8 - Low-Noise 60MHz Precision Op Amp | Analog Devices

MPN: LT1037CJ8 ✓ فعال
10 µV Vdss 8-pin CERDIP, 0.300 inch (7.62 mm) Package 2 Hz Speed
حداقل سفارش: 1 |

LT1037CJ8 نمای کلی

Analog Devices LT1037CJ8 is a single-circuit, low-noise precision operational amplifier with 2.5 nV/√Hz wideband noise, 130 dB common-mode and power-supply rejection, and 60 MHz gain-bandwidth product in an 8-pin CERDIP package. It also provides 10 µV offset voltage and 0.2 µV/°C offset drift, making it suitable for precision signal-chain applications requiring low noise, high rejection, and wide bandwidth.

An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. Within the broader hierarchy of integrated circuits, the LT1037 belongs to the amplifier class and specifically serves as a precision, low-noise voltage-feedback operational amplifier. Its voltage-feedback architecture supports closed-loop signal conditioning, instrumentation, filtering, and buffering while balancing bandwidth, offset performance, and noise.

The LT1037 combines several demanding precision specifications in one device. Its 2.5 nV/√Hz wideband noise is below the thermal noise of a 400 Ω resistor, while the 1/f corner frequency is 2 Hz. The 60 nV peak-to-peak noise over 0.1 Hz to 10 Hz addresses low-frequency interference in sensitive measurements. Offset voltage is specified at 10 µV, and offset drift is 0.2 µV/°C, helping maintain accuracy as temperature changes.

The 130 dB common-mode and power-supply rejection ratios are especially useful when the amplifier operates near ground or receives interference from a changing supply rail. The 60 MHz gain-bandwidth product provides useful speed for wideband instrumentation and signal-processing stages. The decompensated LT1037 configuration is stable for closed-loop gains of 5 or greater, so gain planning must begin at the required system noise gain rather than assuming unity-gain stability.

Typical uses include low-level sensor amplification, precision instrumentation, audio and communications interfaces, photodiode signal chains, and active filtering. In each case, the low-noise input stage can improve the signal-to-noise ratio before further amplification, while high rejection helps isolate the circuit from common-mode and supply-related disturbances.

The principal design consideration is stability. Because the decompensated amplifier requires a closed-loop gain of at least 5, the feedback network and source impedance must provide adequate noise gain across the complete signal bandwidth. Decoupling, grounding, and careful routing of sensitive input and feedback nodes are equally important in low-noise precision designs.

This page combines manufacturer specifications, package and pin information, sourcing guidance, drop-in alternatives, comparison parameters, and practical circuit-design notes. It helps engineers evaluate the LT1037CJ8 for noise-sensitive instrumentation while accounting for its gain stability, offset behavior, supply rejection, and package constraints.

جایگزین‌های drop-in برای LT1037CJ8 — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای LT1037CJ8 (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Amplifier Type, Package.

Analog Devices
Amplifier Type: Single operational amplifier
Package: 8-pin CERDIP
مقایسه با LT1037CJ8 →

LT1007CN8

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-pin CERDIP
Minimum stable closed-loop gain is 5 versus unity-gain-stable operation for LT1037CJ8, a 4-gain-stage stability difference

📋 جایگزین مرجع (خارج از کاتالوگ)

LT1037CJ8 حداکثر مقادیر مجاز و مشخصات الکتریکی

Amplifier Type Precision operational amplifier
Number of Circuits 1 circuit
Gain-Bandwidth Product 60 MHz
Wideband Input Noise Density 2.5 nV/√Hz
Guaranteed 10 Hz Noise Density 4.5 nV/√Hz
Guaranteed 1 kHz Noise Density 3.8 nV/√Hz
0.1 Hz to 10 Hz Peak-to-Peak Noise 60 nV peak-to-peak
1/f Corner Frequency 2 Hz
Offset Voltage 10 µV
Offset Voltage Drift 0.2 µV/°C
Common-Mode Rejection Ratio 130 dB
Power-Supply Rejection Ratio 130 dB
Minimum Stable Closed-Loop Gain 5
بسته‌بندی 8-pin CERDIP, 0.300 inch (7.62 mm)
Terminals 8 terminals
نوع نصب Through-hole
Temperature Grade Commercial

پیکربندی پین LT1037CJ8

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
پین 1 OFFSET NULL — Offset null connection
پین 2 IN- — Inverting input
پین 3 IN+ — Noninverting input
پین 4 V- — Negative supply connection
پین 5 OFFSET NULL — Offset null connection
پین 6 OUT — Output connection
پین 7 V+ — Positive supply connection
پین 8 NC — Not connected

کاربردهای معمول

LT1037CJ8 مناسب است برای 6 کاربردs: Precision Sensor Signal Conditioning, Low-Level Audio Amplification, Instrumentation and Measurement Front Ends, Photodiode and Optical Signal Detection, Active Filters and Signal Conditioning, Industrial Communications Interfaces.

🏭

Precision Sensor Signal Conditioning

The LT1037CJ8 is appropriate for amplifying weak sensor outputs where low input noise, low offset, and high common-mode rejection determine the useful signal level. Its 2.5 nV/√Hz wideband noise and 10 µV offset voltage help preserve small signals close to the measurement floor, while 130 dB common-mode rejection reduces errors from ground shifts or coupled industrial noise. The circuit must maintain a closed-loop noise gain of at least 5 because the decompensated amplifier is not unity-gain stable. Use short input routes, local decoupling, and a clean reference ground to preserve the benefit of the 0.2 µV/°C offset-drift specification.

🎧

Low-Level Audio Amplification

The LT1037CJ8 can serve as a low-noise input amplifier in high-fidelity audio equipment, microphone preamplifiers, and line-level processing stages. Its 2.5 nV/√Hz wideband noise and 60 nV peak-to-peak noise from 0.1 Hz to 10 Hz are particularly valuable when the input source has a low impedance and the signal chain contains substantial gain. The 60 MHz gain-bandwidth product permits wider-band operation than a purely audio-optimized part. Because the amplifier is decompensated, the feedback ratio must establish a noise gain of at least 5, and the input bias-return network should be selected with source impedance and bias-current error in mind.

🔧

Instrumentation and Measurement Front Ends

The LT1037CJ8 is useful in instrumentation front ends that combine signal amplification with high rejection of common-mode and supply disturbances. The 130 dB common-mode and power-supply rejection ratios help isolate small signals in systems with long sensor cables, shared supply rails, or imperfect grounding. Low noise supports measurements where source resistance is low, while 10 µV offset and 0.2 µV/°C drift limit input-referred inaccuracies. Use the decompensated configuration with a closed-loop gain of at least 5, check input and output common-mode limits against the application, and keep feedback components close to the package to minimize parasitic feedback and oscillation risk.

📷

Photodiode and Optical Signal Detection

The LT1037CJ8 can amplify weak photodiode or optical-detector currents when converted into a voltage by a suitable feedback impedance. Its low voltage noise reduces the input-referred contribution from the amplifier itself, and the 130 dB common-mode rejection helps reject coupling from surrounding electronics. The 60 MHz gain-bandwidth product provides bandwidth for transients and moderate-speed detection rather than only static measurements. Designers should account for photodiode capacitance, feedback stability, and the minimum gain of 5 required by the decompensated architecture. A low-capacitance layout and controlled feedback loop are especially important when increasing transimpedance gain.

📡

Active Filters and Signal Conditioning

The LT1037CJ8 supports active-filter and signal-conditioning designs where both noise and frequency response matter. Its 60 MHz gain-bandwidth product provides useful open-loop bandwidth for filters operating well above audio frequencies, while 130 dB power-supply rejection can reduce supply ripple entering the signal path. The 2.5 nV/√Hz input noise is useful when filter gain is applied close to the source. Because this decompensated version requires a closed-loop gain of at least 5, filter topology must provide sufficient noise gain at every frequency. Maintain low parasitic capacitance around the input and feedback nodes and verify phase margin with the actual source impedance and component tolerances.

🌐

Industrial Communications Interfaces

The LT1037CJ8 can be used in receiver and signal-recovery sections of industrial communications equipment where low-level lines are exposed to noise and supply variation. Its 130 dB common-mode rejection is valuable for long, unbalanced interconnects, while the 60 MHz bandwidth supports faster signal transitions than a conventional precision-only amplifier. The 2.5 nV/√Hz noise specification limits the amplifier's own contribution in low-impedance receiver paths. The circuit should use a closed-loop gain of at least 5, provide local supply bypassing, and separate sensitive input routing from digital return currents. Termination and protection components should be selected independently because the amplifier does not replace input clamping or surge handling.

خلاصه محصولات پیشنهادی

LT1037CJ8 Analog Devices استفاده‌شده در: Precision Sensor Signal Conditioning, Low-Level Audio Amplification, Instrumentation and Measurement Front Ends, Photodiode and Optical Signal Detection, Active Filters and Signal Conditioning, Industrial Communications Interfaces LT1007CN8 Same-family amplifier for gain-5-or-higher circuits استفاده‌شده در: Precision Sensor Signal Conditioning, Low-Level Audio Amplification, Instrumentation and Measurement Front Ends, Photodiode and Optical Signal Detection, Active Filters and Signal Conditioning, Industrial Communications Interfaces
What is the LT1037CJ8?
The LT1037CJ8 is a single, low-noise precision operational amplifier manufactured by Analog Devices and offered in an 8-pin CERDIP package. According to the Analog Devices product page, it combines 2.5 nV/√Hz wideband input noise, 60 MHz gain-bandwidth product, 10 µV offset voltage, 0.2 µV/°C drift, and 130 dB common-mode and power-supply rejection. It is intended for instrumentation, filtering, buffering, and other precision analog signal chains.
What are the key specifications of LT1037CJ8 that engineers should know?
The LT1037CJ8 is specified for 2.5 nV/√Hz wideband noise, 60 MHz gain-bandwidth product, 10 µV offset voltage, 0.2 µV/°C offset drift, and 130 dB common-mode and power-supply rejection. According to the Analog Devices product page, its 1/f corner frequency is 2 Hz and its 0.1 Hz to 10 Hz noise is 60 nV peak-to-peak. The decompensated device is stable for closed-loop gains of 5 or greater.
What is the noise performance of LT1037CJ8?
The LT1037CJ8 provides 2.5 nV/√Hz wideband noise, with guaranteed values of 4.5 nV/√Hz at 10 Hz and 3.8 nV/√Hz at 1 kHz. Analog Devices states that this wideband noise is lower than the noise of a 400 Ω resistor. Its 0.1 Hz to 10 Hz peak-to-peak noise is 60 nV, and its 1/f corner frequency is 2 Hz, making it suitable for low-level precision measurements.
Is LT1037CJ8 stable at unity gain?
No. The LT1037CJ8 is a decompensated amplifier that is stable for closed-loop gains of 5 or greater, according to the Analog Devices product page. Its feedback network must therefore establish a noise gain of at least 5 at all frequencies relevant to the signal. A noninverting gain of 5 or more is suitable, while a lower-gain noninverting stage needs added resistor gain because the inverting configuration alone does not create sufficient noise gain.
Where can I download the LT1037CJ8 datasheet PDF?
The official Analog Devices LT1037 product page at https://www.analog.com/en/products/lt1037.html is the authoritative starting point for the LT1037CJ8 datasheet, electrical characteristics, ordering information, and package documentation. Use its document links to select the current manufacturer PDF. The LT1037CJ8 ordering code identifies the commercial-temperature, 8-pin CERDIP configuration, while the family datasheet also covers related LT1007 and LT1037 options.
Where can I find the LT1037CJ8 pinout?
The LT1037CJ8 pinout is documented in the pin-configuration section of the manufacturer datasheet linked from the Analog Devices LT1037 product page. The device uses an 8-pin CERDIP outline with through-hole terminals and a standard dual-inline pin sequence. Use the manufacturer pin-description table when assigning supply, ground, input, output, and unconnected terminals, especially because the decompensated version has different gain-stability requirements from unity-gain-stable family members.
LT1037CJ8 vs LT1007CN8 - which is better for low-noise amplification?
The LT1037CJ8 is the better choice when the design requires unity-gain-stable operation and the lowest wideband noise, while the LT1007CN8 is a decompensated alternative intended for higher closed-loop gains. According to the Analog Devices LT1037 family information, the decompensated configuration is stable for closed-loop gains of 5 or greater. Both use the same 8-pin through-hole family architecture, but the minimum-gain requirement is the decisive selection criterion.
When should I choose LT1037CJ8 over LT1007CN8?
Choose the LT1037CJ8 when the signal path requires unity-gain-stable buffering or signal gain below 5 and low-noise precision is more important than cost or availability of another grade. According to the Analog Devices family description, the decompensated LT1007 configuration requires a closed-loop gain of at least 5. The LT1037 therefore simplifies feedback design for precision buffers, sensor interfaces, and filters whose noise gain cannot easily be forced above 5.
What is the best drop-in replacement for LT1037CJ8?
The LT1007CN8 is the closest same-family drop-in candidate for an existing LT1037CJ8 footprint because it belongs to the same precision, low-noise amplifier family and uses an 8-pin through-hole package. However, it is decompensated and requires a closed-loop gain of at least 5, so it is not a functional substitute when the original circuit operates at unity gain. Confirm stability, offset, noise, and supply requirements against the manufacturer datasheet before replacement.
Can LT1007CN8 replace LT1037CJ8?
The LT1007CN8 can replace the LT1037CJ8 only in circuits whose total noise gain remains at least 5 across the operating bandwidth. Its decompensated architecture does not support unity-gain-stable operation, although it retains the 8-pin through-hole package and low-noise precision positioning. According to the Analog Devices family description, the LT1007/LT1037 series provides 2.5 nV/√Hz wideband noise and 60 MHz gain-bandwidth product.
Is LT1037CJ8 suitable for precision instrumentation?
Yes, the LT1037CJ8 is well suited to precision instrumentation because it combines 10 µV offset voltage, 0.2 µV/°C drift, 130 dB common-mode rejection, and 130 dB power-supply rejection with low input noise. According to the Analog Devices product page, its 60 MHz bandwidth also allows reasonably fast instrumentation channels. The circuit must still provide a closed-loop noise gain of at least 5 and maintain careful grounding around the sensitive input nodes.
How should I design a low-noise LT1037CJ8 circuit?
Design the LT1037CJ8 so its feedback network produces a noise gain of at least 5 and keep the input and feedback traces short. Place input compensation and bypass capacitors close to the device, use a clean ground return for the signal reference, and avoid routing high-current paths near the input pins. Because offset drift is 0.2 µV/°C, thermal gradients near the amplifier can matter even though the common-mode and power-supply rejection ratios are both 130 dB.
What is the lead time for LT1037CJ8?
The current lead time for LT1037CJ8 should be requested through the Request a Quote form on this page. Manufacturer and distributor lifecycle information can change, so the quote team should confirm production status, package allocation, and the requested quantity before committing a build schedule. The part is identified as a commercial-grade, 8-pin CERDIP device, which should be included in the sourcing request to avoid ambiguity with other package or temperature options.
Is LT1037CJ8 in stock?
Stock for LT1037CJ8 should be confirmed through the Request a Quote form on this page. A distributor listing may show immediate shipment for a limited quantity while longer-term supply remains subject to allocation and lifecycle changes. Provide the required quantity, target date, and acceptable package condition in the request so the current factory and channel position can be evaluated against the production plan.
Where can I buy LT1037CJ8 online?
Use the Request a Quote form on this page to request LT1037CJ8 pricing, stock, lead time, and shipment options from XAIPART. Include the exact MPN LT1037CJ8, the required quantity, and any date-sensitive manufacturing requirements. The part is an 8-pin CERDIP commercial-grade operational amplifier, so the quote request should confirm that the ceramic dual-inline package is acceptable for the target assembly process.

داده‌های مرجع مهندسی برای LT1037CJ8 — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the LT1037CJ8 for precision, low-noise amplifier stages that need 60 MHz bandwidth, 10 µV offset voltage, 130 dB rejection, and unity-gain-stable operation. It is particularly suitable for sensor interfaces, active filters, audio inputs, and instrumentation where the source impedance is low enough for the amplifier's noise to matter. Choose LT1007CN8 only when the complete feedback network maintains a noise gain of at least 5 and the decompensated architecture is acceptable. Because fewer than five verified drop-in equivalents exist for the exact 8-pin CERDIP ordering code, engineers should treat that alternative as a family-level option rather than a blanket substitute. Before replacing the LT1037CJ8, verify offset, drift, noise, common-mode range, supply range, stability, and package dimensions against the manufacturer datasheet.

مقایسه با جایگزین‌ها

پارامتر این محصول LT1007CN8
Brand Analog Devices Analog Devices
Package 8-pin CERDIP 8-pin CERDIP
Amplifier Type Precision operational amplifier Precision operational amplifier
Gain-Bandwidth Product 60 MHz 60 MHz
Wideband Input Noise Density 2.5 nV/√Hz 2.5 nV/√Hz
Offset Voltage 10 µV 10 µV
Offset Voltage Drift 0.2 µV/°C 0.2 µV/°C
Common-Mode Rejection Ratio 130 dB 130 dB
Power-Supply Rejection Ratio 130 dB 130 dB
Minimum Stable Closed-Loop Gain 1 5
Mounting Type Through-hole Through-hole

تفاوت‌های کلیدی

  • Unity-gain-stable operation simplifies precision buffer layouts (در مقابلLT1007CN8)
  • Low wideband noise supports high-gain analog front ends (در مقابلLT1007CN8)
  • High rejection reduces errors from common-mode and supply disturbances (در مقابلLT1007CN8)
  • Low offset drift supports temperature-dependent precision measurements (در مقابلLT1007CN8)

یادداشت‌های طراحی

The most important LT1037CJ8 design constraint is its decompensated stability requirement. The feedback network must create a noise gain of at least 5 across the relevant bandwidth; otherwise the amplifier may oscillate or have unexpectedly poor phase margin. In a noninverting amplifier, set the closed-loop gain to 5 or higher. In an inverting amplifier, add sufficient resistor gain because a unity-gain inverting stage still presents approximately unity noise gain at the inverting input.

Route the LT1037CJ8 input, feedback, and offset-null connections as short as practical, and place compensation or bypass capacitors near their associated pins. Keep high-current supply and return paths away from the input reference to avoid converting supply current into differential input noise. Because the amplifier offers 130 dB power-supply rejection, good supply decoupling remains necessary rather than being replaced by that specification. Confirm the final stability and phase margin with actual source impedance and component tolerances.

The 0.2 µV/°C offset-drift specification makes thermal gradients relevant in precision circuits. Place the amplifier away from heat sources, avoid forced air crossing that creates unequal temperatures across the package, and use symmetrical board placement when possible. Estimated offset change for a uniform 25 °C temperature rise is 5 µV using the specified 0.2 µV/°C drift; this is a design calculation rather than a guaranteed application error because gradients and bias effects can add further error.

Use the input protection and bias-return network carefully because both can add noise or compromise the LT1037CJ8's low-noise performance. Avoid excessive capacitance at the input, use low-noise feedback resistors when resistor thermal noise dominates, and check that protection leakage remains small relative to the source current. For photodiode, electrochemical, or high-impedance sensors, the input bias current and leakage of surrounding components may matter more than the amplifier's voltage noise.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The LT1037CJ8 is a commercial-grade precision operational amplifier. No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified in the cited manufacturer and distributor pages.

تاریخ تأیید داده‌ها: 2026-11-14 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

LT1037CJ8 datasheet LT1037CJ8 pinout LT1037CJ8 datasheet pdf LT1037CJ8 equivalent LT1037CJ8 replacement LT1037CJ8 vs LT1007CN8 LT1037CJ8 footprint LT1037CJ8 application circuit Analog Devices LT1037CJ8 LT1037CJ8 price LT1037CJ8 stock LT1037 8 pin CERDIP pinout LT1037 60MHz low noise op amp LT1037CJ8 precision instrumentation amplifier

قطعات و اصطلاحات مرتبط

Analog Devices Linear Technology LT1037CJ8 LT1037 LT1007 LT1007CN8 precision operational amplifier low-noise amplifier voltage-feedback amplifier amplifier IC integrated circuit semiconductor 2.5 nV/√Hz noise density 60 MHz gain-bandwidth product 130 dB common-mode rejection 130 dB power-supply rejection 10 µV offset voltage 0.2 µV/°C offset drift decompensated amplifier closed-loop gain of 5 8-pin CERDIP dual-inline package through-hole package precision instrumentation
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ