MCP659-E/ML - 50MHz Quad Rail-to-Rail Op Amp | Microchip
MPN: MCP659-E/ML ✓ فعالMCP659-E/ML نمای کلی
Operational amplifiers are active semiconductor devices that amplify the difference between two input voltages. They are used within analog signal chains, including sensor interfaces, filtering, instrumentation, buffering, and control systems. The MCP659-E/ML belongs to the MCP65x family of low-offset operational amplifiers and combines four amplifiers in one quad package. Its rail-to-rail input and output structure allows operation near the supply rails, while the 50 MHz bandwidth supports higher-frequency signal paths than low-bandwidth precision amplifiers.
Key characteristics include a typical gain-bandwidth product of 50 MHz, typical slew rate of 30 V/us, typical short-circuit current of 100 mA, and typical voltage-noise density of 7.5 nV/sqrt(Hz) at 1 MHz. The calibrated input offset is specified at a maximum of ±200 uV. The operating temperature range is -40 C to +125 C. The MCP659-E/ML is supplied in a 16-QFN package, with an exposed-pad package designation associated with the -ML ordering code.
The mCal function is particularly relevant to precision dc applications because it performs an offset-calibration sequence at power-up. The manufacturer datasheet also notes that some MCP65x package options include a calibration/chip-select pin for low-power operation and offset calibration. Designers should review the exact pin configuration, timing requirements, and calibration behavior for the selected package before laying out the PCB.
Typical uses include industrial sensor conditioning, portable measurement systems, low-noise analog front ends, instrumentation, and multi-channel signal acquisition. When designing around the MCP659-E/ML, provide stable bypassing close to the supply pins, account for amplifier stability with the selected feedback network and load capacitance, and verify that the operating voltage and temperature remain within the device ratings.
This product page organizes the manufacturer information, datasheet references, package details, application guidance, and qualification questions for engineers evaluating the MCP659-E/ML. The MCP659 family is presented as a general-purpose, four-circuit rail-to-rail operational-amplifier solution with mCal-enabled offset calibration.
جایگزین‌های drop-in برای MCP659-E/ML — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
MCP659T-E/ML
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MCP659-E/ML حداکثر مقادیر مجاز و مشخصات الکتریکی
| Amplifier Number | 4 circuits |
| Device Type | General-purpose operational amplifier |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| ولتاژ تغذیه | 2.5 V minimum per specification listing |
| Gain-Bandwidth Product | 50 MHz typical |
| Slew Rate | 30 V/us typical |
| Short-Circuit Current | 100 mA typical |
| Voltage Noise Density | 7.5 nV/sqrt(Hz) typical at 1 MHz |
| Calibrated Input Offset Voltage | ±200 uV maximum |
| Input Bias Current | 5 nA typical |
| Common-Mode Rejection Ratio | 81 dB |
| محدوده دمای کاری | -40 C to +125 C |
| بسته‌بندی | 16-QFN, 4 x 4 mm |
| Calibration Technology | mCal self-calibration at power-up |
راهنمای پیکربندی پین MCP659-E/ML 16-qfn, 4 x 4 mm
پیکربندی پین برای MCP659-E/ML (پکیج 16-qfn, 4 x 4 mm). این قطعه آنالوگ دارای پین‌های ورودی، خروجی و تغذیه است. برای پیکربندی‌های پین offset null، جبران‌سازی و فعال‌سازی به دیتاشیت سازنده مراجعه کنید. ایده‌آل برای مدارهای شرطی‌سازی سیگنال و تقویت‌کننده.
داده پین‌آوت تفصیلی موجود نیست برای MCP659-E/ML.
به دیتاشیت برای پیکربندی کامل پین‌ها.
کاربردهای معمول
MCP659-E/ML مناسب است برای 6 کاربردs: Industrial Sensor Signal Conditioning, Portable Measurement Systems, Precision Instrumentation Front Ends, Analog Filtering and Buffering, Data Acquisition Signal Chains, General-Purpose Analog Control.
Industrial Sensor Signal Conditioning
The MCP659-E/ML is suitable for conditioning outputs from industrial sensors that operate near the available supply rails. Its rail-to-rail input and output behavior preserves usable signal range in low-voltage systems, while the calibrated input offset of ±200 uV maximum helps reduce dc error in instrumentation paths. The 50 MHz typical gain-bandwidth product also allows the amplifier to handle moderate-bandwidth sensor signals when paired with appropriate filtering. Use stable supply bypassing, verify input and output limits under load, and select external resistor values that do not reduce practical accuracy through excessive noise or mismatch.
پیشنهادی
Portable Measurement Systems
MCP659-E/ML fits portable measurement systems that need several amplifier channels in a compact package. Rail-to-rail inputs and outputs improve headroom when the system operates from a constrained supply, and the four circuits allow designers to combine signal conditioning, filtering, and buffering without using four separate packages. The 50 MHz typical bandwidth provides margin for signal paths that are faster than low-frequency sensor-only circuits. Battery-powered designs should still evaluate supply current, noise, startup calibration behavior, and the effect of the power source on analog accuracy.
پیشنهادی
Precision Instrumentation Front Ends
The MCP659-E/ML is useful in instrumentation front ends where several low-frequency-to-moderate-bandwidth channels require accurate amplification and buffering. Its 81 dB CMRR helps reject common-mode disturbance, and the mCal power-up self-calibration supports low-offset operation. The 50 MHz gain-bandwidth product provides sufficient speed for filtering and gain stages, while rail-to-rail outputs increase usable signal swing. Designers should confirm noise performance over the required measurement bandwidth, account for resistor and reference tolerances, and use the exact MCP659-E/ML pin configuration from the manufacturer datasheet.
پیشنهادی
Analog Filtering and Buffering
With four amplifiers in one 16-QFN package, the MCP659-E/ML can implement active filters, gain stages, and buffers around sensors or converters. Its 30 V/us typical slew rate and 50 MHz typical gain-bandwidth product make it appropriate for many signal-conditioning tasks where low offset is also desirable. Stable operation depends on the selected feedback topology, noise gain, source impedance, and capacitive loading. Check the datasheet stability guidance and include output isolation when driving long cables or capacitive loads.
پیشنهادی
Data Acquisition Signal Chains
MCP659-E/ML can provide analog conditioning immediately before an ADC in a multi-channel data-acquisition system. Four amplifiers in one package reduce board-area requirements compared with four single-amplifier packages, while the 50 MHz bandwidth can support sampling paths above very low-frequency instrumentation rates. The rail-to-rail input characteristic supports wide common-mode coverage, and mCal helps reduce offset error after startup. Confirm the ADC input range, acquisition settling requirements, antialiasing filter design, and whether channel-to-channel matching is sufficient for the measurement architecture.
پیشنهادی
General-Purpose Analog Control
The MCP659-E/ML is appropriate for general-purpose analog control and feedback loops that need rail-to-rail operation and low offset. The self-calibrating architecture can improve startup behavior in systems that depend on precise amplifier output around the zero point. Its 50 MHz bandwidth and 30 V/us slew rate are useful for driving moderate loads and implementing active compensation, but stability must be verified for each feedback network. Pay attention to output-current limits, capacitive-load behavior, power-supply noise, and temperature effects across the intended operating range.
پیشنهادی
داده‌های مرجع مهندسی برای MCP659-E/ML — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | MCP659T-E/ML |
|---|---|---|
| Package | 16-QFN (4x4) | 16-QFN (4x4) |
| Brand | Microchip Technology | Microchip Technology |
| Amplifier Number | 4 circuits | 4 circuits |
تفاوت‌های کلیدی
- Four amplifier channels in one compact package (در مقابلMCP659T-E/ML)
- Power-up offset self-calibration (در مقابلMCP659T-E/ML)
- Wide signal range for compact analog systems (در مقابلMCP659T-E/ML)
یادداشت‌های طراحی
The MCP659-E/ML requires a supply within the device limits and should be decoupled with the capacitor network recommended in the MCP65x datasheet. Place the bypass capacitors close to the supply pins, keep the high-current return path short, and account for the power-up sequence required by mCal. In systems with a noisy upstream converter, verify the amplifier’s power-supply rejection at the frequencies present on the rail rather than assuming the supply is clean.
Use the 16-QFN package drawing and exposed-pad guidance from the manufacturer datasheet when designing the land pattern. Route the four amplifier channels with short, symmetric traces where channel matching matters, and keep the power and ground connections low-inductance. Avoid placing sensitive signal routes beneath the exposed pad unless the PCB stackup and thermal design explicitly support that arrangement. Check assembly tolerances and the manufacturer’s soldering profile for the selected package.
Do not assume that the generic 16-QFN pin arrangement is identical to the MCP659-E/ML pinout. The available product information identifies the package and amplifier count but does not reproduce the numbered pin descriptions, so use the MCP65x datasheet pin table before assigning tracks. Also check the CAL/CS timing behavior for the applicable package and confirm that the mCal startup sequence is compatible with the system power architecture.
Estimate dissipation from the actual supply voltage, output swing, load current, and operating duty cycle rather than using a generic regulator-style calculation. The 16-QFN package’s exposed pad should be tied to the appropriate ground plane and connected with adequate thermal vias to spread heat into the PCB. Use the manufacturer’s power-rating and package thermal information when defining the maximum ambient temperature and deciding whether additional copper or thermal management is required.
اطلاعات انطباق
The manufacturer datasheet and product information in the verified material do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements. Compliance status must be confirmed on the manufacturer product page or ordering documentation before qualification.
