MKE04Z8VFK4 - 48MHz Cortex-M0+ 8KB Flash MCU, 24-QFN | NXP
MPN: MKE04Z8VFK4 ✓ فعالMKE04Z8VFK4 نمای کلی
A microcontroller is the programmable control core of an embedded system, sitting between raw sensors and power stages on one side and actuators, communications links and human interfaces on the other. The Kinetis KE04 family extends the NXP Kinetis E series concept into a cost-sensitive, 5 V-capable tier with enhanced ESD and EMC behaviour, positioning it as a rugged general-purpose MCU (microcontroller unit) for electrically noisy environments.
Key characteristics of the MKE04Z8VFK4 include a 48 MHz Cortex-M0+ core with 8 KB of flash (8K x 8) for firmware, 1 KB of SRAM for working data, 6-bit and 12-bit analog conversion capability, and operation from a single 3.3 V or 5 V supply rail. The 24-QFN (4x4 mm) footprint keeps the board area small while exposing a thermal pad for improved heat spreading.
Architecturally the device belongs to the Kinetis E series, a low-cost branch of the Kinetis portfolio built on the ARM Cortex-M0+ instruction set. The M0+ core adds a small set of DSP-like instructions and an improved NMI path over the original Cortex-M0, while the modest flash budget of 8 KB makes the part a natural fit for tightly scoped control tasks rather than protocol stacks or graphical user interfaces.
Typical applications include industrial control and monitoring nodes, small appliance control boards, LED lighting control, automotive accessory controllers, and smart sensor hubs that must survive electrically aggressive surroundings. The 4x4 mm package and low-power modes also suit battery-backed utility and metering peripherals.
When designing around this device, plan the printed circuit board for the exposed pad thermal connection, keep decoupling close to the supply pins, and confirm the exact ADC and I/O pin assignment from the manufacturer pin description table before committing the layout. Firmware budgets should respect the 8 KB flash ceiling, which usually means using the on-chip peripherals rather than large protocol middleware.
This page consolidates manufacturer part data, drop-in alternatives in the same footprint, a parameter-by-parameter comparison, and practical PCB and firmware design notes that a distributor catalogue listing alone does not provide.
جایگزین‌های drop-in برای MKE04Z8VFK4 — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای MKE04Z8VFK4 (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package.
MKE04Z8VFG4
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MKE04Z64VFK4
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
MKE04Z4VFK4
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
MKE02Z8VFK4
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
MKE04Z8VFK4 حداکثر مقادیر مجاز و مشخصات الکتریکی
| Core / Architecture | ARM Cortex-M0+, 32-bit RISC |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 8 KB (8K x 8) |
| SRAM | 1 KB |
| Product Family | Kinetis KE04 (Kinetis E series) |
| بسته‌بندی | 24-QFN (4x4 mm), exposed pad |
| تعداد پین‌ها | 24 |
| ولتاژ تغذیه کاری | 3.3 V / 5 V |
| ADC Resolution | 6-bit and 12-bit |
| ESD / EMC Robustness | Enhanced ESD/EMC performance for high electrical noise environments |
| نوع نصب | Surface mount |
| Shipping Method | Tray |
| Datasheet Document Length | 33 pages |
راهنمای پیکربندی پین MKE04Z8VFK4 24-qfn (4x4 mm), exposed pad
پیکربندی پین برای MKE04Z8VFK4 (پکیج 24-qfn (4x4 mm), exposed pad). این IC دیجیتال شامل GPIO، رابط‌های ارتباطی (UART، SPI، I2C) و پین‌های تغذیه است. برای عملکردهای جایگزین پین و گزینه‌های پیکربندی به دیتاشیت سازنده مراجعه کنید. ضروری برای طراحی سیستم‌های نهفته و چیدمان PCB.
داده پین‌آوت تفصیلی موجود نیست برای MKE04Z8VFK4.
به دیتاشیت برای پیکربندی کامل پین‌ها.
کاربردهای معمول
MKE04Z8VFK4 مناسب است برای 6 کاربردs: Industrial Monitoring and Control Node, Small Appliance Control Board, LED Lighting Control and Driver Board, Automotive and 12 V Accessory Controller, IoT Sensor Hub and Smart Home Node, Utility Metering and Energy Measurement Front End.
Industrial Monitoring and Control Node
The MKE04Z8VFK4 fits factory monitoring nodes because the Kinetis KE04 family is characterised by enhanced ESD and EMC performance for high electrical noise environments, and the 3.3 V or 5 V single-rail operation simplifies factory power trees. Its 48 MHz Cortex-M0+ core handles sensor polling, filtering and a Modbus-style register map well within the 8 KB flash budget, while 1 KB of SRAM is adequate for buffered samples. In practice the device is placed between a resistive or current-sense input stage and a differential output driver, keeping the analog path short. The 4x4 mm 24-QFN footprint leaves room for the optocouplers and protection components typically required on an industrial node, and a companion I/O expander such as the PCA9554ADBR can add digital lines without enlarging the board.
پیشنهادی
Small Appliance Control Board
Household and kitchen appliances need a controller that survives motor and heater switching noise while keeping the bill of materials low. The MKE04Z8VFK4 delivers that combination through 3.3 V or 5 V operation, enhanced ESD and EMC behaviour, and an 8 KB flash budget that is ample for a state machine, timer and a small display or keypad driver. The 24-QFN (4x4 mm) package is small enough to sit next to a triac or relay driver stage, shortening the high-current traces. A practical arrangement places the MCU on the neutral side of the mains stage with a series resistor network feeding the ADC channels, and uses an optically isolated interface such as the SP3232EET-L/TR family member for external service communication.
پیشنهادی
LED Lighting Control and Driver Board
LED lighting modules need accurate current control, dimming and fault reporting in a compact board. The MKE04Z8VFK4 handles this with 6-bit and 12-bit analog conversion channels for monitoring the LED string voltage, and its 48 MHz Cortex-M0+ core is fast enough to run PWM dimming with high resolution. The 8 KB flash limit favors a focused firmware design: a closed-loop dimming algorithm plus a small fault log rather than a large application framework. In a typical implementation the MCU sits beside the LED driver IC and periodically corrects the duty cycle, and the exposed pad of the 24-QFN package keeps the thermal path short on tightly packed modules.
پیشنهادی
Automotive and 12 V Accessory Controller
Body accessory modules in 12 V vehicles need a controller that tolerates load dump, reverse battery and cranking transients while staying inexpensive. The MKE04Z8VFK4 offers 3.3 V or 5 V single-rail operation and enhanced ESD and EMC performance, which suits rugged accessory control for pumps, wipers or seat modules; a front-end network interface such as the KSZ9131RNXC transceiver covers body-network communication where required. Because the device is not an AEC-Q100-qualified automotive part, use it in non-safety-critical accessory positions or verify the specific ordering code for automotive temperature and qualification levels. Firmware typically handles relay or MOSFET drive, current sensing through the ADC channels and diagnostic reporting over a low-speed serial link.
پیشنهادی
IoT Sensor Hub and Smart Home Node
A smart home sensor node needs to gather readings, apply simple local logic and forward data over a low-power link, all from a minimal bill of materials. The MKE04Z8VFK4 suits this role through its 48 MHz Cortex-M0+ core, low-power modes and 3.3 V operation, which fits coin-cell or USB powered nodes running a thin protocol stack inside the 8 KB flash allowance. The 24-QFN (4x4 mm) footprint fits inside compact enclosures where a larger plastic package would not. A typical design pairs the MCU with a small wireless or ethernet transceiver such as the KSZ8721BL-TR and a sensor front end, and the microcontroller performs debouncing, calibration and OTA-flag handling before handing data to the network controller.
پیشنهادی
Utility Metering and Energy Measurement Front End
Energy meters and utility data concentrators need deterministic measurement, tamper detection and long product lifetimes in compact enclosures. The MKE04Z8VFK4 contributes a 12-bit conversion path for current and voltage sensing, a 48 MHz core for energy accumulation and a 3.3 V or 5 V rail that matches cost-sensitive metering designs. Its enhanced ESD and EMC performance is valuable in DIN-rail and outdoor cabinets where surge and switching noise are common. Because the 8 KB flash budget restricts the firmware, the metering algorithm is usually kept minimal while a communications co-processor, for example a KSZ9893RNXC-class ethernet device or an SP485-series transceiver, handles protocol traffic.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای MKE04Z8VFK4 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | MKE04Z8VFG4 | MKE04Z64VFK4 | MKE04Z4VFK4 | MKE02Z8VFK4 |
|---|---|---|---|---|---|
| Package | 24-QFN (4x4 mm) | 24-QFN (4x4 mm) - same footprint | 24-QFN (4x4 mm) - same footprint | 24-QFN (4x4 mm) - same footprint | 24-QFN (4x4 mm) - same footprint |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core / Architecture | ARM Cortex-M0+, 32-bit | ARM Cortex-M0+, 32-bit | ARM Cortex-M0+, 32-bit | ARM Cortex-M0+, 32-bit | ARM Cortex-M0+, 32-bit |
| Flash Memory | 8 KB (8K x 8) | 8 KB | 64 KB (+700%) | 4 KB (-50%) | 8 KB |
| Operating Supply Voltage | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V | 3.3 V / 5 V |
تفاوت‌های کلیدی
- 48 MHz Cortex-M0+ with 8 KB flash in a 4x4 mm footprint (در مقابلMKE02Z8VFK4)
- Same memory size and pinout as the closest ordering variant (در مقابلMKE04Z8VFG4)
- Balanced flash size for cost versus future growth (در مقابلMKE04Z64VFK4)
- Analog conversion without an external ADC (در مقابلMKE04Z4VFK4)
یادداشت‌های طراحی
The MKE04Z8VFK4 is a 24-QFN (4x4 mm) device with an exposed pad. Give the pad a dedicated ground pour and connect it with multiple vias to the ground plane, and keep the pad copper free of the high-current switching return path of a relay or triac stage. Place the bulk input capacitor and the decoupling capacitor directly between the supply pin and the exposed pad on the component side, and route the supply trace on the top layer so its return current does not cross the sensitive analog inputs.
Because the Kinetis KE04 family targets high electrical noise environments, treat analog and digital returns separately. Keep the 12-bit and 6-bit converter inputs on the quiet side of the board, away from relay contacts, motor windings and inductor switching nodes, and terminate unused converter channels to a defined potential rather than leaving them floating. If the board mixes mains-derived and low-voltage domains, route the isolation barrier so no copper or ground pour bridges the two, and keep the MCU-side ground reference a single continuous pour.
The most common design failure with this device is running out of flash. The 8 KB (8K x 8) program memory must hold the bootloader, the application, calibration data and any protocol handler, so build with a linker map that reserves the top flash addresses for configuration and check the image size at every release. A second common mistake is assuming 5 V tolerance on every I/O pin; check the pin description table in the manufacturer datasheet for the pins that are 3.3 V only when the rail is shared.
Plan the 3.3 V or 5 V rail with a margin that covers input transients. Estimated: with a 5 V nominal rail, a 1 A peak load on a resistive actuator branch and roughly 20 percent regulator efficiency, the supply must sustain about 1.25 A continuous to avoid brownout during switching. Confirm the supply tolerance and the MCU current consumption figures from the datasheet electrical characteristics table before fixing the input capacitance, and verify the clock trimming tolerance if the design relies on the internal oscillator for timing.
اطلاعات انطباق
The part is listed as active by NXP. No RoHS, REACH or halogen-free declaration was captured for this ordering code, so these fields remain unknown. The KE04 family is not an AEC-Q100 automotive-qualified range; confirm automotive requirements on the specific ordering code before use in vehicle applications.
