PIC16C62AT-20I/SS - 8-Bit OTP MCU, 3.5KB, 20MHz | Microchip
MPN: PIC16C62AT-20I/SS ⚠ آخرین فرصت خریدPIC16C62AT-20I/SS نمای کلی
What is a PIC microcontroller? A PIC (Peripheral Interface Controller) microcontroller is a small, low-power embedded computer on a single integrated circuit, combining a CPU, RAM, non-volatile program memory, and peripherals such as timers, ADC, comparators, and serial communication blocks. PIC microcontrollers sit within the broader category of microcontrollers (MCU) and 8-bit embedded processors, and they are widely used in industrial control, appliance, automotive, and consumer applications where deterministic behaviour and low cost matter more than raw compute.
Key features of the PIC16C62AT-20I/SS include 22 I/O pins, two 8-bit timers plus one 16-bit timer with capture/compare/PWM capability, a 5-channel 8-bit analog-to-digital converter (ADC), a USART/SCI serial port, an I2C/SPI-compatible Synchronous Serial Port (SSP), and a watchdog timer with its own on-chip RC oscillator for maximum reliability. The 14-bit instruction set provides 35 single-word instructions, and the device supports interrupt-driven operation with up to 10 interrupt sources.
The PIC16C62AT-20I/SS is built on a fully-static CMOS technology and uses a Harvard architecture with separate program and data buses, enabling simultaneous instruction fetch and data access. Power management includes power-on reset (POR), brown-out reset (BOR), power-saving SLEEP mode, and a wide operating voltage range. The 'T' suffix denotes tape-and-reel packaging, '-20' denotes 20MHz maximum clock, 'I' indicates the industrial temperature grade (-40C to +85C), and 'SS' specifies the SSOP-28 package.
Typical applications include industrial control and automation, sensor interfacing, motor control, small home appliances, automotive body electronics, instrumentation, low-power remote-control units, and embedded control subsystems in larger equipment.
When designing with this OTP part, remember that the program memory can be written only once; for prototyping or in-field updates consider the flash-memory PIC16F62x family, which is pin-compatible and provides migration headroom.
This page synthesises distributor pricing, drop-in PIC16C family alternatives from the same SSOP-28 footprint, and engineering design notes not found in the manufacturer datasheet alone.
جایگزین‌های drop-in برای PIC16C62AT-20I/SS — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای PIC16C62AT-20I/SS (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Timers, RoHS Status, Program Memory Type, Core Architecture.
PIC16C62A-20I/SS
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC16C62AT-20I/SO
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC16C62B-20I/SS
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
PIC16C622A-20I/SS
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
PIC16F628A-I/SS
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC16F88-I/SS
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC16C622AT-20I/SS
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC16C62AT-20I/SS حداکثر مقادیر مجاز و مشخصات الکتریکی
| Core | 8-bit PIC16 (Harvard) |
| Instruction Set | 14-bit, 35 instructions |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 3.5 KB (2K x 14) |
| RAM | 128 bytes |
| Data EEPROM | Not present |
| Maximum CPU Frequency | 20 MHz |
| Supply Voltage (Vdd) | 2.5 V to 6.0 V |
| I/O Pins | 22 |
| Timers | 2 x 8-bit + 1 x 16-bit (CCP) |
| ADC | 5 channels, 8-bit |
| Serial Interfaces | USART/SCI + SSP (I2C/SPI) |
| Watchdog Timer | Yes (with on-chip RC) |
| دمای کاری | -40C to +85C (Industrial) |
| بسته‌بندی | 28-SSOP (0.209", 5.30mm width) |
| نوع نصب | Surface Mount |
| وضعیت RoHS | Non-compliant (contains Pb, OTP legacy family) |
پیکربندی پین PIC16C62AT-20I/SS
| پین 1 | RA2/AN2/VREF- — Port A bit 2 / ADC input 2 / ADC negative reference |
| پین 2 | RA3/AN3/VREF+ — Port A bit 3 / ADC input 3 / ADC positive reference |
| پین 3 | RA4/T0CKI — Port A bit 4 / Timer0 clock input (open-drain output) |
| پین 4 | RA5/AN4/SS — Port A bit 5 / ADC input 4 / SPI slave select |
| پین 5 | Vss — Ground reference |
| پین 6 | OSC1/CLKIN — Oscillator crystal input / external clock in |
| پین 7 | OSC2/CLKOUT — Oscillator crystal output / clock out |
| پین 8 | RC0/T1OSO/T1CKI — Port C bit 0 / Timer1 oscillator output / Timer1 clock in |
| پین 9 | RC1/T1OSI/CCP2 — Port C bit 1 / Timer1 oscillator input / CCP2 output |
| پین 10 | RC2/CCP1 — Port C bit 2 / CCP1 PWM/capture input or output |
| پین 11 | RC3/SCK/SCL — Port C bit 3 / SPI clock / I2C clock |
| پین 12 | RC4/SDI/SDA — Port C bit 4 / SPI data in / I2C data |
| پین 13 | RC5/SDO — Port C bit 5 / SPI data out |
| پین 14 | RC6/TX/CK — Port C bit 6 / USART TX / USART clock |
| پین 15 | RC7/RX/DT — Port C bit 7 / USART RX / USART data |
| پین 16 | RB0/INT — Port B bit 0 / external interrupt |
| پین 17 | RB1 — Port B bit 1 |
| پین 18 | RB2 — Port B bit 2 |
| پین 19 | RB3 — Port B bit 3 |
| پین 20 | RB4 — Port B bit 4 |
| پین 21 | RB5 — Port B bit 5 |
| پین 22 | RB6/PGC — Port B bit 6 / ICSP clock |
| پین 23 | RB7/PGD — Port B bit 7 / ICSP data |
| پین 24 | Vdd — Positive supply |
| پین 25 | Vss — Ground reference |
| پین 26 | RA0/AN0 — Port A bit 0 / ADC input 0 |
| پین 27 | RA1/AN1 — Port A bit 1 / ADC input 1 |
| پین 28 | MCLR/Vpp — Master clear reset (active low) / programming voltage |
کاربردهای معمول
PIC16C62AT-20I/SS مناسب است برای 6 کاربردs: Industrial Sensor Conditioning, Home Appliance Control, Automotive Body Electronics (Cabin), Instrumentation and Metering, Motor Control Subsystems, Embedded Control and I/O Expansion.
Industrial Sensor Conditioning
The PIC16C62AT-20I/SS fits industrial sensor conditioning boards where a deterministic 8-bit core plus on-chip ADC and USART simplify 4-20 mA or RS-485 sensor front-ends. Its 5-channel 8-bit ADC samples thermocouple, RTD-bridge, or pressure-sensor signals without an external analogue front end, and the integrated USART talks to a host PLC or industrial gateway. Operating from 2.5 V to 6.0 V and -40C to +85C, the part is tolerant of factory-supply noise and wide temperature swings; 128 bytes RAM accommodates small linearisation tables and a moving-average filter. Use the watchdog timer and brown-out reset blocks to recover from EMI-induced hangs on long sensor cables.
پیشنهادی
Home Appliance Control
In small home appliances such as microwave ovens, washing-machine sub-modules, induction cookers, and air-conditioner remotes, the PIC16C62AT-20I/SS drives relays, triacs, LEDs, and keypads while running simple state machines in OTP memory. Its 22 I/O pins cover multi-digit seven-segment displays and a keypad matrix without external logic; the 16-bit CCP timer generates PWM for fan-speed or triac phase-angle control. The industrial temperature range and wide 2.5-6.0 V supply accommodate rectified mains-derived rails, while the 20 MHz instruction rate delivers 5 MIPS for de-bounce and timing logic.
پیشنهادی
Automotive Body Electronics (Cabin)
For non-safety cabin modules such as interior lighting controllers, seat-position memories, mirror adjusters, and HVAC flaps, the PIC16C62AT-20I/SS operates across the automotive 12 V regulated rail via a 5 V LDO and provides the USART link to a body-control network. The 5-channel ADC reads multi-position switch inputs and potentiometers for trim and mirror position, while the SSP block drives SPI-controlled LED drivers. Designers pair it with the PIC16C62AT-20E/SS extended-temperature grade for higher-thermal zones; for AEC-Q100 qualified builds migrate to the automotive-qualified PIC16F family.
پیشنهادی
Instrumentation and Metering
Digital panel meters, hand-held multimeters, and process-control indicators use the PIC16C62AT-20I/SS to drive LCD segments or LED displays, sample a 4-20 mA or 0-10 V transducer signal, and run a calibration menu on a few buttons. The on-chip ADC handles the transducer with software linearisation, while the SSP block connects to an external EEPROM for calibration constants. The PIC16C62A's low power-down current and SLEEP mode extend battery life in portable instruments, and the SSOP-28 footprint keeps the BOM small inside compact housings.
پیشنهادی
Motor Control Subsystems
Small DC, brushless, or stepper motor controllers for pumps, fans, and small appliances leverage the PIC16C62AT-20I/SS's 16-bit CCP/PWM block to generate a precision PWM drive, while the 8-bit timers time the commutation events for sensored BLDC operation. The USART enables a service-port or wired remote control link for diagnostics or speed-set commands. With 5 MIPS at 20 MHz, the part implements PI loops, soft-start ramps, and stall-detection firmware in firmware, all within 3.5 KB of OTP. Industrial-grade temperature handling supports enclosed motor housings.
پیشنهادی
Embedded Control and I/O Expansion
Designers use the PIC16C62AT-20I/SS as a low-cost I/O expander and supervisory co-processor alongside a more powerful host processor or SoC, offloading keypad scanning, LED driving, watchdog supervision, and discrete GPIO expansion over I2C or SPI. The on-board USART/SSP block makes a clean protocol bridge to the host, and 22 I/O lines add meaningful peripheral count without consuming host pins. With its industrial temperature grade and proven PIC16C reliability, the part serves as a robust housekeeping MCU in POS terminals, vending machines, and industrial HMIs.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای PIC16C62AT-20I/SS — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | PIC16C62A-20I/SS | PIC16C62B-20I/SS | PIC16C622A-20I/SS | PIC16F628A-I/SS | PIC16F88-I/SS |
|---|---|---|---|---|---|---|
| Package | SSOP-28 (5.30mm) | SSOP-28 (5.30mm) - same | SSOP-28 (5.30mm) - same | SSOP-28 (5.30mm) - same | SSOP-28 (5.30mm) - same | SSOP-28 (5.30mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB OTP | 3.5 KB Flash | 4 KB Flash |
| Maximum CPU Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| RAM | 128 bytes | 128 bytes | 128 bytes | 128 bytes | 224 bytes | 368 bytes |
| EEPROM | Not present | Not present | Not present | Not present | 128 bytes | 256 bytes |
| ADC | 5-ch x 8-bit | 5-ch x 8-bit | 5-ch x 8-bit | 5-ch x 8-bit | None (comparators only) | 7-ch x 10-bit |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) |
| RoHS / Lead-Free | Non-RoHS (legacy Pb) | Non-RoHS (legacy Pb) | Non-RoHS (legacy Pb) | Non-RoHS (legacy Pb) | RoHS compliant (Pb-free) | RoHS compliant (Pb-free) |
| Reprogrammable | No (OTP) | No (OTP) | No (OTP) | No (OTP) | Yes (Flash, 100k cycles) | Yes (Flash, 100k cycles) |
تفاوت‌های کلیدی
- Industrial temperature grade (-40C to +85C) as standard (در مقابلPIC16C62AT-20I/SO)
- On-chip ADC and USART integrate analog and comms (در مقابلPIC16F628A-I/SS)
- Wider supply voltage range than flash successors (در مقابلPIC16F628A-I/SS)
یادداشت‌های طراحی
PIC16C62AT-20I/SS draws roughly 2 mA at 5 V / 20 MHz with all peripherals enabled and falls to under 1 uA in SLEEP mode. Decouple Vdd with a 100 nF ceramic placed within 5 mm of the Vdd/Vss pins and bulk the rail with at least 10 uF; add an RC low-pass on Vpp/MCLR (typical 10 kohm + 100 nF) to ensure a clean power-on-reset. For battery-backed designs, the brown-out reset block should be enabled with a BOR voltage below the minimum Vdd of 2.5 V to avoid spurious resets during sleep.
Place the decoupling capacitor as close as possible to pins 24 (Vdd) and 25 (Vss), and route the MCLR/Vpp pin through a 10 kohm pull-up to Vdd with a 100 nF to ground for the ICSP programming interface. The OSC1/OSC2 traces should be short and guarded by a ground ring; for crystal operation select a fundamental-mode XTAL with 15-33 pF load capacitors matched to the crystal ESR. Avoid routing the analog inputs RA0-RA5 near the OSC2 trace to minimise ADC clock-coupling noise; if used, shield the analog tracks with a ground pour.
Estimated: writing the OTP program memory of the PIC16C62AT-20I/SS consumes approximately 30 seconds per device at production programming time, and OTP cannot be erased - so always burn a 'final' golden build after validation. Ensure configuration bits (fuses) are explicitly set rather than left at default, especially the watchdog enable (default off), BOR voltage, and oscillator mode. Reserve RB6/RB7 for ICSP - if the application drives them as outputs, disable the LVP bit and use HVP, otherwise the part will enter programming mode unexpectedly at power-up.
اطلاعات انطباق
PIC16C family OTP parts are generally non-RoHS (legacy Pb terminal finish) and not AEC-Q100 qualified; Microchip flags the family as last-time-buy for many SKUs. Industrial temperature grade is supported (-40C to +85C) but automotive-grade temperature and EMI qualification require migration to the PIC16F flash family.
