PIC16F627T-04/SS - 8-bit Flash MCU, 4MHz, SSOP-20 | Microchip
MPN: PIC16F627T-04/SS ✓ فعالPIC16F627T-04/SS نمای کلی
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data RAM, non-volatile EEPROM, and peripheral blocks such as timers, comparators, and I/O ports into one package. Microcontrollers sit within the broader semiconductor hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. The PIC16F62X family uses a Harvard architecture in which program and data buses are separated, allowing instruction fetch and operand read to occur in a single 200 ns instruction cycle at 20 MHz.
Key features include 16 I/O pins with individually programmable direction, two analog comparators with programmable on-chip voltage reference, a Watchdog Timer with its own on-chip RC oscillator for reliable operation, Brown-out Detect (BOD), Power-on Reset (POR), Power-up Timer (PWRT) and Oscillator Start-up Timer (OST). Multiplexed MCLR and programmable weak pull-ups on PORTB further reduce external component count, while an internal 4 MHz RC oscillator enables designs without an external crystal.
Architecturally, the device combines a RISC instruction set with only 35 single-word instructions, an 8-level deep hardware stack, and direct, indirect, and relative addressing modes. The CMOS process delivers low power consumption suitable for battery-friendly applications while maintaining the noise immunity needed for industrial environments.
Typical applications include appliance control, automotive subsystems, industrial monitoring, remote controls, and low-end consumer products. The wide operating voltage and built-in peripherals also support sensor interfacing and simple closed-loop control. The device is well-suited as a replacement for legacy 8-bit designs that require flash re-programmability rather than one-time programmable (OTP) memory.
When designing with this part, ensure decoupling capacitors are placed close to VDD/VSS and that the configuration bits for oscillator selection and watchdog are reviewed before code release. The 'T' suffix in the part number indicates tape-and-reel packaging, and the '04' suffix specifies the 4 MHz maximum operating frequency.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet to help engineers shorten the component selection cycle.
جایگزین‌های drop-in برای PIC16F627T-04/SS — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای PIC16F627T-04/SS (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Operating Temperature, Analog Comparators, Timers, I/O Pins.
PIC16F627-04/SS
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC16F627-04I/SS
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC16F627-04E/SS
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC16F627A-I/SS
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC16F627AT-I/SS
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC16F627-20I/P
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC16F627-20E/SS
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC16F628-04I/SS
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
PIC16F627T-04/SS حداکثر مقادیر مجاز و مشخصات الکتریکی
| Core Architecture | 8-bit PIC16 RISC (Harvard) |
| Instruction Set Width | 14-bit |
| Program Memory Type | Flash |
| Program Memory Size | 1.75 KB |
| Data SRAM | 224 bytes |
| Data EEPROM | 128 bytes |
| حداکثر فرکانس کلاک | 4 MHz |
| Instruction Cycle Time | 1 us at 4 MHz |
| Supply Voltage (VDD) | 4.5 V to 5.5 V |
| I/O Pins | 16 |
| Timers | 3 (Timer0, Timer1, Timer2) |
| Analog Comparators | 2 with programmable VREF |
| PWM Modules | 1 (CCP) |
| Watchdog Timer | Yes, with dedicated on-chip RC oscillator |
| Brown-out Detect (BOD) | Yes |
| بسته‌بندی | SSOP-20 (5.30 mm body width) |
| نوع نصب | Surface Mount |
| دمای کاری | -40C to +85C (commercial/industrial) |
| سطح MSL | 1 |
| وضعیت RoHS | Compliant |
پیکربندی پین PIC16F627T-04/SS
| پین 1 | RA2/AN2 — GPIO RA2 / analog input AN2 |
| پین 2 | RA3/AN3/CMP1 — GPIO RA3 / analog input AN3 / comparator 1 output |
| پین 3 | RA4/AN4/T0CKI — GPIO RA4 / analog input AN4 / Timer0 clock input |
| پین 4 | RA5/MCLR/VPP — GPIO RA5 / master clear reset / programming voltage input |
| پین 5 | VSS — Ground reference |
| پین 6 | RB0/INT — GPIO RB0 / external interrupt input |
| پین 7 | RB1/RX/DT — GPIO RB1 / USART RX / data line |
| پین 8 | RB2/TX/CK — GPIO RB2 / USART TX / clock line |
| پین 9 | RB3/CCP1 — GPIO RB3 / Capture-Compare-PWM 1 output |
| پین 10 | RB4/PGM — GPIO RB4 / low-voltage programming input |
| پین 11 | RB5 — GPIO RB5 |
| پین 12 | RB6/PGC — GPIO RB6 / ICSP clock input |
| پین 13 | RB7/PGD — GPIO RB7 / ICSP data I/O |
| پین 14 | VDD — Positive supply voltage (4.5 V to 5.5 V) |
| پین 15 | OSC2/CLKOUT — Crystal oscillator output / clock output |
| پین 16 | OSC1/CLKIN — Crystal oscillator input / external clock input |
| پین 17 | RA7/OSC1 — GPIO RA7 / alternate crystal oscillator input (LP/HS mode) |
| پین 18 | RA6/OSC2 — GPIO RA6 / alternate crystal oscillator output |
| پین 19 | RA1/AN1 — GPIO RA1 / analog input AN1 |
| پین 20 | RA0/AN0 — GPIO RA0 / analog input AN0 |
کاربردهای معمول
PIC16F627T-04/SS مناسب است برای 7 کاربردs: Appliance Control, Remote Control and IR Transmitters, Industrial Sensor Monitoring, Automotive Body Electronics, Battery Charger Control, Security and Access Control Panels, LED Lighting Drivers.
Appliance Control
The PIC16F627T-04/SS fits appliance control designs requiring low-cost 8-bit processing with on-chip EEPROM for storing user settings. Its 16 I/O pins handle keypad scanning, relay drive, and seven-segment display multiplexing without external logic. The CCP/PWM module drives motor speed control or heating element proportional control, while the dual comparators implement over-temperature or over-current protection with the programmable VREF setting the trip threshold. Brown-out Detect and Watchdog Timer are critical for white-goods safety certification.
پیشنهادی
Remote Control and IR Transmitters
The PIC16F627T-04/SS is well-matched to consumer remote controls where low cost, low power, and 4 MHz operation are sufficient. The internal 4 MHz RC oscillator eliminates the external crystal, reducing BOM cost on space-constrained PCB layouts. The 1.75 KB flash holds IR protocol firmware (RC5, NEC, SIRC), 224 B SRAM holds buffer state, and 128 B EEPROM retains paired-device codes across battery swaps. Sleep current in the nanoampere range supports coin-cell operation for years.
پیشنهادی
Industrial Sensor Monitoring
The PIC16F627T-04/SS fits industrial sensor monitoring applications such as 4-20 mA loop signal conditioning or thermistor readout where dual analog comparators set thresholds without an ADC. Its programmable VREF module calibrates the comparator trip at up to 8 discrete levels, supporting temperature window alarms or pressure switch replacements. The 5 V supply rails and SSOP-20 footprint suit densely packed control boards in factory automation equipment.
پیشنهادی
Automotive Body Electronics
The PIC16F627T-04/SS supports non-safety automotive body modules such as interior lighting, mirror control, and HVAC damper actuation. The 16 I/O pins drive multiple LED strings directly through MOSFET gates, and the CCP/PWM provides smooth dimming without flicker. Brown-out Detect rides through automotive cranking transients while the Watchdog Timer recovers from firmware lockups. Designers should pair this part with external load-dump TVS protection on VDD.
پیشنهادی
Battery Charger Control
The PIC16F627T-04/SS implements CC/CV charge profiles for sealed lead-acid, NiMH, or Li-ion packs in low-power chargers. The internal VREF module and dual comparators measure battery voltage and charge current without an ADC, while the CCP/PWM modulates a switching FET for current regulation. The 128 B EEPROM stores charge-cycle counters and battery-capacity logs across power cycles, supporting smart-charging features at minimal BOM cost.
پیشنهادی
Security and Access Control Panels
The PIC16F627T-04/SS is a fit for keypad entry panels, simple alarm control units, and RFID reader front-ends. Its 16 I/O pins scan a 4x4 matrix keypad, drive status LEDs, and interface to an external UART radio or GSM module. The 128 B EEPROM holds up to 50 user codes, while flash stores modular firmware. Brown-out Detect and Watchdog Timer ensure the panel recovers cleanly from power glitches or RF interference.
پیشنهادی
LED Lighting Drivers
The PIC16F627T-04/SS drives multi-channel LED fixtures in architectural and accent lighting. The CCP/PWM module provides smooth 10-bit dimming, while additional I/O pins operate as GPIO drivers for additional channels via external MOSFETs. The internal 4 MHz oscillator keeps BOM cost low, and the SSOP-20 footprint allows compact driver PCBs. EEPROM stores calibrated brightness curves per zone, recalled via user input or DMX-like serial protocol.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای PIC16F627T-04/SS — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | PIC16F627-04/SS | PIC16F627-04I/SS | PIC16F627A-I/SS | PIC16F627AT-I/SS | PIC16F628-04I/SS |
|---|---|---|---|---|---|---|
| Package | SSOP-20 | SSOP-20 - same | SSOP-20 - same | SSOP-20 - same | SSOP-20 - same | SSOP-20 - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Maximum Clock Frequency | 4 MHz | 4 MHz | 4 MHz | 20 MHz | 20 MHz | 4 MHz |
| Program Memory | 1.75 KB | 1.75 KB | 1.75 KB | 1.75 KB | 1.75 KB | 3.5 KB |
| Data SRAM | 224 bytes | 224 bytes | 224 bytes | 224 bytes | 224 bytes | 224 bytes |
| Data EEPROM | 128 bytes | 128 bytes | 128 bytes | 128 bytes | 128 bytes | 128 bytes |
| I/O Pins | 16 | 16 | 16 | 16 | 16 | 16 |
| Operating Temperature | Commercial | Commercial | Industrial -40C to +85C | Industrial -40C to +85C | Industrial -40C to +85C | Industrial -40C to +85C |
| RoHS Compliance | Compliant | Compliant | Compliant | Compliant | Compliant | Compliant |
تفاوت‌های کلیدی
- Tape-and-reel factory packaging for SMT production (در مقابلPIC16F627-04/SS)
- Commercial temperature grade at lowest cost (در مقابلPIC16F627-04I/SS)
- Dual analog comparators with programmable VREF (در مقابلPIC16F628-04I/SS)
یادداشت‌های طراحی
Place a 100 nF decoupling capacitor as close as possible to the VDD pin (pin 14) with a short, wide ground return to the VSS pin (pin 5). Add a bulk 10 uF tantalum or aluminum electrolytic capacitor on the same supply rail if the design sources current from a switching regulator. The PIC16F627T-04/SS has no internal POR slope requirements, but rapid VDD rise times below 50 mV/us may trigger BOD on some lots. Source: Microchip PIC16F62X family datasheet, section 'Oscillator Configurations'.
Route the OSC1 and OSC2 traces short and symmetric when using an external crystal, and keep them away from high-current switching traces to avoid capacitive coupling. For the multiplexed MCLR/VPP pin, do not place a capacitor larger than 100 nF on the reset line; otherwise in-circuit serial programming (ICSP) may fail. The ICSP PGC and PGD pins (RB6 and RB7) should have no series resistors above 10 kohm in production PCB layouts. Source: Microchip PIC16F62X datasheet ICSP section.
Do not connect analog inputs above VDD or below VSS, even by 0.3 V, on the PIC16F627 - the analog multiplexer does not include clamping diodes on all channels. Set the CMCON register to disable comparators on unused pins if analog inputs are used as digital GPIO. Estimated: power consumption at 4 MHz and 5 V is approximately 2 mA active and 1 uA in Sleep, but verify against the latest datasheet electrical characteristics table for your temperature grade.
When using the internal 4 MHz RC oscillator, calibration drift over temperature is approximately +/- 2 percent across the commercial range. For UART communication, this limits reliable baud rates to 9600 baud or below at extreme temperatures without periodic recalibration via the OSCTUNE register. If UART stability is critical, use an external crystal or resonator. Source: Microchip PIC16F627 datasheet 'Oscillator Calibration' section.
اطلاعات انطباق
RoHS compliance per Microchip product page. The PIC16F627 family is not AEC-Q100 qualified; automotive designs requiring Q100 should use PIC16F18323 or similar newer AEC-Q100 parts. Halogen-free status not explicitly confirmed in web data.
