PIC18F6410-E/PT - 8-bit MCU, 16KB Flash, 40MHz, 64-Pin TQFP
MPN: PIC18F6410-E/PT ✓ فعالPIC18F6410-E/PT نمای کلی
An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path and Harvard architecture. It executes C, assembly, or graphical code to read sensors, drive actuators, and exchange data over serial protocols. In the broader hierarchy, a microcontroller sits inside the semiconductor category, the embedded computing category, and ultimately inside the system-on-chip (SoC) parent family, alongside 16-bit, 32-bit, and 64-bit MCUs.
Key features of the PIC18F6410-E/PT include 16 KB of self-programmable Flash, 768 bytes of SRAM, 256 bytes of EEPROM, 54 digital I/O, a 10-bit ADC with multiple channels, two analog comparators, two USART modules, MSSP (SPI/I2C), a 16-bit timer, three 8-bit timers, nanoWatt Technology for low-power modes, an enhanced 16-bit capture/compare/PWM module, and an ICD/ICSP debug interface. The TQFP-64 footprint exposes nearly all peripherals to external pins.
Architecturally, the device uses a 16-bit instruction word with 8-bit data path and a 31-level hardware stack. nanoWatt Technology supports run, idle, and sleep modes with on-the-fly oscillator switching. The extended instruction set, hardware multiplier, and C-friendly architecture make it suitable for control loops and protocol stacks.
Typical applications include industrial manufacturing equipment, instrumentation and monitoring, data acquisition, power conditioning, environmental monitoring, telecom, and consumer devices. It is also used in white goods and HVAC controllers where 8-bit MCUs with rich peripherals and 5V tolerance are preferred.
When designing with this part, verify the operating temperature grade. The -E suffix denotes an extended temperature range of -40C to +125C, suitable for industrial and outdoor enclosures. Decouple VDD/VSS with 100 nF capacitors placed within 5 mm of each pin pair, and keep the ICSP clock and data traces short.
This page synthesizes distributor pricing, drop-in alternatives from the PIC18F family, and practical design notes not found in the manufacturer datasheet alone.
جایگزین‌های drop-in برای PIC18F6410-E/PT — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای PIC18F6410-E/PT (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Operating Temperature, Timers, RAM, ADC.
PIC18F6410-I/PT
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
PIC18F6410T-I/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC18F6410T-E/PT
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
PIC18LF6410-I/PT
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
PIC18LF6410-E/PT
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
PIC18F6410-E/PT حداکثر مقادیر مجاز و مشخصات الکتریکی
| Family | PIC18F |
| Core Architecture | 8-bit RISC (PIC) |
| Program Memory (Flash) | 16 KB |
| RAM | 768 bytes |
| EEPROM | 256 bytes |
| Maximum Clock Speed | 40 MHz |
| MIPS | 10 MIPS |
| ولتاژ تغذیه | 4.2 V to 5.5 V |
| Digital I/O Pins | 54 (max) |
| ADC | 10-bit, multi-channel |
| Analog Comparators | 2 |
| USART | 2 |
| MSSP (SPI / I2C) | 1 |
| Timers | 1x 16-bit + 3x 8-bit |
| Operating Temperature Range (E grade) | -40C to +125C |
| بسته‌بندی | TQFP-64 (PT), 10 x 10 mm, 1 mm height |
| نوع نصب | Surface Mount |
| Lead-Free / RoHS | Lead-free per Microchip datasheet |
| Debug / Programming | ICSP / ICD |
پیکربندی پین PIC18F6410-E/PT
| پین 1 | RC0/T1OSO/T13CKI — I/O port C bit 0 / Timer1 oscillator output / Timer1 clock input |
| پین 2 | RC1/T1OSI/CCP2 — I/O port C bit 1 / Timer1 oscillator input / CCP2 output |
| پین 3 | RC2/CCP1 — I/O port C bit 2 / CCP1 I/O |
| پین 4 | RC3/SCK/SCL — I/O port C bit 3 / SPI clock / I2C clock |
| پین 5 | RC4/SDI/SDA — I/O port C bit 4 / SPI data in / I2C data |
| پین 6 | RC5/SDO — I/O port C bit 5 / SPI data out |
| پین 7 | RC6/TX1/CK1 — I/O port C bit 6 / USART1 async transmit / sync clock |
| پین 8 | RC7/RX1/DT1 — I/O port C bit 7 / USART1 async receive / sync data |
| پین 9 | VSS — Ground reference |
| پین 10 | VDD — Positive supply (4.2V-5.5V) |
| پین 11 | RB0/INT0/FLT0 — I/O port B bit 0 / External interrupt 0 / PWM fault input |
| پین 12 | RB1/INT1 — I/O port B bit 1 / External interrupt 1 |
| پین 13 | RB2/INT2 — I/O port B bit 2 / External interrupt 2 |
| پین 14 | RB3/INT3 — I/O port B bit 3 / External interrupt 3 |
| پین 15 | RB4/KBI0 — I/O port B bit 4 / Keyboard interrupt 0 |
| پین 16 | RB5/KBI1 — I/O port B bit 5 / Keyboard interrupt 1 |
| پین 17 | RB6/KBI2/PGC — I/O port B bit 6 / Keyboard interrupt 2 / ICSP clock |
| پین 18 | RB7/KBI3/PGD — I/O port B bit 7 / Keyboard interrupt 3 / ICSP data |
| پین 19 | VSS — Ground reference |
| پین 20 | VDD — Positive supply (4.2V-5.5V) |
| پین 21 | RA0/AN0 — I/O port A bit 0 / Analog input 0 |
| پین 22 | RA1/AN1 — I/O port A bit 1 / Analog input 1 |
| پین 23 | RA2/AN2/VREF- — I/O port A bit 2 / Analog input 2 / ADC VREF- |
| پین 24 | RA3/AN3/VREF+ — I/O port A bit 3 / Analog input 3 / ADC VREF+ |
| پین 25 | RA4/T0CKI — I/O port A bit 4 / Timer0 clock input |
| پین 26 | RA5/AN4/SS/HLVDIN — I/O port A bit 5 / Analog input 4 / SPI slave select / HLVD input |
| پین 27 | RA6/OSC2/CLKO — I/O port A bit 6 / Crystal output / Clock output |
| پین 28 | RA7/OSC1/CLKI — I/O port A bit 7 / Crystal input / Clock input |
| پین 29 | VSS — Ground reference |
| پین 30 | VDD — Positive supply (4.2V-5.5V) |
| پین 31 | RF0 — I/O port F bit 0 |
| پین 32 | RF1 — I/O port F bit 1 |
| پین 33 | RF2 — I/O port F bit 2 |
| پین 34 | RF3 — I/O port F bit 3 |
| پین 35 | RF4 — I/O port F bit 4 |
| پین 36 | RF5 — I/O port F bit 5 |
| پین 37 | RF6 — I/O port F bit 6 |
| پین 38 | RF7 — I/O port F bit 7 |
| پین 39 | VSS — Ground reference |
| پین 40 | VDD — Positive supply (4.2V-5.5V) |
| پین 41 | RG0 — I/O port G bit 0 |
| پین 42 | RG1 — I/O port G bit 1 |
| پین 43 | RG2 — I/O port G bit 2 |
| پین 44 | RG3 — I/O port G bit 3 |
| پین 45 | RG4 — I/O port G bit 4 |
| پین 46 | RE0/RD/AN5 — I/O port E bit 0 / Read control / Analog input 5 |
| پین 47 | RE1/WR/AN6 — I/O port E bit 1 / Write control / Analog input 6 |
| پین 48 | RE2/CS/AN7 — I/O port E bit 2 / Chip select / Analog input 7 |
| پین 49 | RE3 — I/O port E bit 3 |
| پین 50 | VSS — Ground reference |
| پین 51 | VDD — Positive supply (4.2V-5.5V) |
| پین 52 | RD0/PSP0 — I/O port D bit 0 / Parallel slave port bit 0 |
| پین 53 | RD1/PSP1 — I/O port D bit 1 / Parallel slave port bit 1 |
| پین 54 | RD2/PSP2 — I/O port D bit 2 / Parallel slave port bit 2 |
| پین 55 | RD3/PSP3 — I/O port D bit 3 / Parallel slave port bit 3 |
| پین 56 | RD4/PSP4 — I/O port D bit 4 / Parallel slave port bit 4 |
| پین 57 | RD5/PSP5 — I/O port D bit 5 / Parallel slave port bit 5 |
| پین 58 | RD6/PSP6/TX2/CK2 — I/O port D bit 6 / PSP bit 6 / USART2 TX / sync clock |
| پین 59 | RD7/PSP7/RX2/DT2 — I/O port D bit 7 / PSP bit 7 / USART2 RX / sync data |
| پین 60 | VSS — Ground reference |
| پین 61 | VDD — Positive supply (4.2V-5.5V) |
| پین 62 | MCLR/VPP/RE5 — Master clear reset / Programming voltage / I/O RE5 |
| پین 63 | C1OUT/RE6 — Comparator 1 output / I/O port E bit 6 |
| پین 64 | C2OUT/RE7 — Comparator 2 output / I/O port E bit 7 |
کاربردهای معمول
PIC18F6410-E/PT مناسب است برای 6 کاربردs: Industrial Manufacturing Equipment, Instrumentation and Monitoring, Data Acquisition Systems, Power Conditioning and Control, Environmental Monitoring, Telecom and Consumer Devices.
Industrial Manufacturing Equipment
The PIC18F6410-E/PT fits industrial controllers with its 40 MHz PIC18 core, 16 KB Flash, 768 bytes RAM, and 54 digital I/O. The -E grade operating range of -40C to +125C tolerates factory floor heat near motors and motor drives. Hardware timers drive PWM for actuator control, while the 10-bit ADC reads back motor current or position. The C-friendly architecture lets designers port MPLAB XC8 firmware from PIC18F45K22 designs with little rework, and ICSP/ICD enables in-field firmware updates on installed equipment.
پیشنهادی
Instrumentation and Monitoring
For panel meters, sensor transmitters, and laboratory instruments, the PIC18F6410-E/PT provides a 10-bit multi-channel ADC, two analog comparators, and USART/MSSP for serial reporting. Its 16 KB Flash is enough for calibration tables, linearization routines, and Modbus ASCII/RTU stacks. The 5V tolerance matches legacy analog front-ends, and the extended temperature grade supports outdoor and cabinet-mounted installations.
پیشنهادی
Data Acquisition Systems
Multi-channel data loggers benefit from the PIC18F6410-E/PT's 10-bit ADC, MSSP for external FRAM/EEPROM storage, and USART for PC upload. The 768 bytes of SRAM buffer incoming samples while a foreground task writes to non-volatile memory. The 16 KB Flash holds logger firmware plus a small FAT-style file layer. The TQFP-64 footprint leaves room for analog signal conditioning on a 4-layer PCB.
پیشنهادی
Power Conditioning and Control
Power supply controllers, UPS sense boards, and battery monitoring modules use the PIC18F6410-E/PT for its 10-bit ADC sampling current/voltage, hardware PWM for synchronous drive signals, and 5V-tolerant I/O for opto-isolated feedback paths. The extended temperature grade supports inside-enclosure operation near transformers. nanoWatt idle/sleep modes cut quiescent draw during standby.
پیشنهادی
Environmental Monitoring
Air quality, weather stations, and HVAC sensor nodes pair the PIC18F6410-E/PT with serial CO2, humidity, and particulate sensors via USART/MSSP. Its 16 KB Flash runs averaging/filtering code, and the 256-byte EEPROM stores calibration offsets. The -E grade supports rooftop and outdoor enclosures. Low sleep current via nanoWatt extends battery life in solar-powered deployments.
پیشنهادی
Telecom and Consumer Devices
Peripheral-rich consumer appliances and telecom endpoint controllers use the PIC18F6410-E/PT for display/keypad interfaces, USART links to modems, and PWM for buzzer or LED brightness. The PIC18 architecture is widely supported by MPLAB XC8 and a large library of application notes. The TQFP-64 package keeps the BOM small and the layout two-sided where cost matters.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای PIC18F6410-E/PT — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | PIC18F6410-I/PT | PIC18F6410T-I/PT | PIC18F6410T-E/PT | PIC18LF6410-I/PT | PIC18LF6410-E/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-64 (PT), 10x10 mm | TQFP-64 (PT), 10x10 mm - same | TQFP-64 (PT), 10x10 mm - same | TQFP-64 (PT), 10x10 mm - same | TQFP-64 (PT), 10x10 mm - same | TQFP-64 (PT), 10x10 mm - same |
| Program Memory (Flash) | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| RAM | 768 bytes | 768 bytes | 768 bytes | 768 bytes | 768 bytes | 768 bytes |
| Operating Temperature | -40C to +125C (E grade) | -40C to +85C (I grade) | -40C to +85C (I grade) | -40C to +125C (E grade) | -40C to +85C (I grade) | -40C to +125C (E grade) |
| Supply Voltage | 4.2V to 5.5V | 4.2V to 5.5V | 4.2V to 5.5V | 4.2V to 5.5V | 2.0V to 5.5V | 2.0V to 5.5V |
| Maximum Clock Speed | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| Digital I/O Pins | 54 | 54 | 54 | 54 | 54 | 54 |
تفاوت‌های کلیدی
- Extended temperature grade for harsh environments (در مقابلPIC18F6410-I/PT)
- Lower-voltage compatibility in the same footprint (در مقابلPIC18LF6410-E/PT)
- Full nanoWatt Technology power management (در مقابلPIC18F8410-E/PT)
یادداشت‌های طراحی
Decouple each VDD pin pair with a 100 nF X7R ceramic capacitor placed within 5 mm of the pins. For the 64-pin TQFP there are six VDD/VSS pairs (pins 9/10, 19/20, 29/30, 39/40, 50/51, 60/61). Bulk-decouple the supply rail with a 4.7 uF to 10 uF tantalum or polymer cap. When migrating to the LF variant, ensure the regulator can source at least 40 MHz oscillator current at 2.0V (typically 4-6 mA additional headroom).
Route the ICSP clock (PGC, RB6) and data (PGD, RB7) traces as short as possible and away from switching signals. The TQFP-64 (PT) has a 0.5 mm pitch, so use 0.15 mm/0.20 mm trace-and-space and stitch vias under the exposed thermal pad if present. Keep the crystal traces (RA6/RA7) within 5 mm of the MCU to avoid stray capacitance and EMI.
Do not exceed the 5.5V absolute maximum on VDD; the PIC18F6410 is a 5V part, not 3.3V-tolerant. For 3.3V-only rails, choose PIC18LF6410 instead. Verify the -E temperature grade when the enclosure sits near heat sources: -40C to +125C is wider than the -40C to +85C industrial grade. The MCLR pin requires a 10 kohm pull-up to VDD if not driven by an external supervisor.
اطلاعات انطباق
Lead-free TQFP-64 package per Microchip PIC18F6310/6410 datasheet. RoHS/REACH compliance per Microchip product page. AEC-Q100 not applicable for non-automotive PIC18F6410.
