PIC18F65J50T-I/PT - 48MHz 8-bit USB MCU 32KB Flash | Microchip
MPN: PIC18F65J50T-I/PT ✓ فعالPIC18F65J50T-I/PT نمای کلی
What is an 8-bit microcontroller? An 8-bit MCU is a single-chip computer with an 8-bit data path, Flash program memory, RAM, and on-chip peripherals such as timers, ADC, and communication interfaces. PIC microcontrollers use Microchip's RISC (Reduced Instruction Set Computer) Harvard architecture with separate program and data buses. Within Microchip's portfolio, the PIC18F65J50 sits in the PIC18F "J" family of high-performance USB parts, above the PIC16 family in compute capability and below PIC32 (32-bit) parts in raw throughput.
Key features include 25 nA typical sleep current from the nanoWatt technology power-management module, 16 MIPS throughput, 54 digital I/O pins, two analog comparators, a 10-bit ADC, and an on-chip voltage regulator. The wide supply range of 2.0-3.6 V (core from internal regulator; I/O 4.2-5.5 V per package rating) allows single-rail 3.3 V operation. Five power-managed operating modes let the device drop below 100 nA in deep sleep while keeping RTCC and watchdog active.
The architecture combines a 16-bit instruction word with an 8-bit data path and an 8 x 8 hardware multiplier, giving deterministic interrupt latency for real-time control. Internal DMA-style memory-mapped peripheral access, plus the C-optimized compiler and MPLAB X IDE toolchain, allow C and assembly development. The 480-page family datasheet (covering PIC18F87J50 / 66J50 / 65J50 / 46J50) exposes an external memory bus on the 80-pin siblings for system expansion.
Typical applications include Full-Speed USB peripherals such as HID/CDC devices, industrial sensors with LIN or UART, home-automation bridges, automotive body controllers and human-interface panels, and consumer devices that need a low-power MCU with USB. Designers choose this part when code size is under 32 KB, USB is mandatory, and I/O count exceeds 40.
When designing, note that the J-series parts run core from an internal 2.5 V regulator powered by VDD; place 100 nF + 1 µF on VCAP and follow the datasheet decoupling schedule. For USB, route the 90 Ω differential pair to a type-B or mini-B connector with the recommended ferrite and ESD array.
This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping procurement and firmware engineers evaluate the PIC18F65J50T-I/PT against modern USB MCU requirements.
جایگزین‌های drop-in برای PIC18F65J50T-I/PT — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای PIC18F65J50T-I/PT (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Timers, ADC, Operating Temperature, I/O Pins.
PIC18F65J50-I/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC18F66J55-I/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC18F66J50-I/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC18F67J50-I/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC18F65J11-I/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC18F65J10-I/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC18F65J50T-I/PT حداکثر مقادیر مجاز و مشخصات الکتریکی
| Core | PIC18 RISC, 8-bit data path, 16-bit instruction word |
| Family | PIC18F "J" Series (PIC18F6xJ50 / 8xJ50) |
| Maximum CPU Speed | 48 MHz (16 MIPS) |
| Program Memory (Flash) | 32 KB (16K x 16) |
| Data RAM | 3.8 KB |
| USB Peripheral | USB 2.0 Full-Speed (12 Mbit/s), device mode |
| I/O Pins | 54 |
| ولتاژ تغذیه | 4.2 V to 5.5 V (I/O); 2.0 V to 3.6 V (VDDCORE from internal regulator) |
| دمای کاری | -40 °C to +85 °C (industrial, "I") |
| بسته‌بندی | 64-pin TQFP (PT), 10x10 mm, 0.5 mm pitch |
| نوع نصب | Surface Mount |
| ADC | 10-bit, multiple channels |
| Analog Comparators | 2 |
| Timers | Multiple 8-bit and 16-bit timers (per family datasheet) |
| Communication Interfaces | USB FS, MI²C, SPI up to 10 Mbit/s, 2x EUSART (LIN-capable) |
| Power-Saving Modes | nanoWatt: Run, Idle, Sleep, Deep Sleep, RC_RUN; ~25 nA typical sleep |
| سطح MSL | 3 (per JEDEC J-STD-020) |
| وضعیت RoHS | Compliant |
پیکربندی پین PIC18F65J50T-I/PT
| پین 1 | RC1 — Digital I/O port C bit 1 / ECCP PWM output |
| پین 2 | RC2 — Digital I/O port C bit 2 / ECCP PWM output |
| پین 3 | RC3 — Digital I/O port C bit 3 / SPI SCK |
| پین 4 | RC4 — Digital I/O port C bit 4 / SPI SDI |
| پین 5 | RC5 — Digital I/O port C bit 5 / SPI SDO |
| پین 6 | VSS — Ground reference (digital) |
| پین 7 | VDD — Positive supply for I/O and USB (2.0-3.6 V) |
| پین 8 | RB0 — Digital I/O port B bit 0 / INT0 |
| پین 9 | RB1 — Digital I/O port B bit 1 / INT1 |
| پین 10 | RB2 — Digital I/O port B bit 2 / INT2 |
| پین 11 | RB3 — Digital I/O port B bit 3 / INT3 |
| پین 12 | RB4 — Digital I/O port B bit 4 |
| پین 13 | RB5 — Digital I/O port B bit 5 / PGEC1 ICSP clock |
| پین 14 | RB6 — Digital I/O port B bit 6 / PGED1 ICSP data |
| پین 15 | RB7 — Digital I/O port B bit 7 |
| پین 16 | VSS — Ground reference (digital) |
| پین 17 | VDD — Positive supply (2.0-3.6 V) |
| پین 18 | RA0 — Digital I/O port A bit 0 / AN0 analog input |
| پین 19 | RA1 — Digital I/O port A bit 1 / AN1 analog input |
| پین 20 | RA2 — Digital I/O port A bit 2 / AN2 analog input |
| پین 21 | RA3 — Digital I/O port A bit 3 / AN3 analog input |
| پین 22 | RA4 — Digital I/O port A bit 4 / T0CKI timer0 |
| پین 23 | RA5 — Digital I/O port A bit 5 / AN4 analog input |
| پین 24 | VSS — Ground reference (digital) |
| پین 25 | VDD — Positive supply (2.0-3.6 V) |
| پین 26 | RF0 — Digital I/O port F bit 0 |
| پین 27 | RF1 — Digital I/O port F bit 1 |
| پین 28 | RF2 — Digital I/O port F bit 2 |
| پین 29 | RF3 — Digital I/O port F bit 3 |
| پین 30 | RF4 — Digital I/O port F bit 4 |
| پین 31 | RF5 — Digital I/O port F bit 5 |
| پین 32 | RF6 — Digital I/O port F bit 6 |
| پین 33 | RF7 — Digital I/O port F bit 7 |
| پین 34 | RG0 — Digital I/O port G bit 0 |
| پین 35 | RG1 — Digital I/O port G bit 1 |
| پین 36 | RG2 — Digital I/O port G bit 2 |
| پین 37 | RG3 — Digital I/O port G bit 3 |
| پین 38 | RG4 — Digital I/O port G bit 4 |
| پین 39 | AVSS — Analog ground |
| پین 40 | AVDD — Analog positive supply |
| پین 41 | RE0 — Digital I/O port E bit 0 / AN5 analog input |
| پین 42 | RE1 — Digital I/O port E bit 1 / AN6 analog input |
| پین 43 | RE2 — Digital I/O port E bit 2 / AN7 analog input |
| پین 44 | RE3 — Digital I/O port E bit 3 |
| پین 45 | RE4 — Digital I/O port E bit 4 |
| پین 46 | RE5 — Digital I/O port E bit 5 |
| پین 47 | RE6 — Digital I/O port E bit 6 |
| پین 48 | RE7 — Digital I/O port E bit 7 |
| پین 49 | RD0 — Digital I/O port D bit 0 / PSP0 |
| پین 50 | RD1 — Digital I/O port D bit 1 / PSP1 |
| پین 51 | RD2 — Digital I/O port D bit 2 / PSP2 |
| پین 52 | RD3 — Digital I/O port D bit 3 / PSP3 |
| پین 53 | RD4 — Digital I/O port D bit 4 / PSP4 |
| پین 54 | RD5 — Digital I/O port D bit 5 / PSP5 |
| پین 55 | RD6 — Digital I/O port D bit 6 / PSP6 |
| پین 56 | RD7 — Digital I/O port D bit 7 / PSP7 |
| پین 57 | VSS — Ground reference (digital) |
| پین 58 | OSC1 — External crystal / oscillator input |
| پین 59 | OSC2 — External crystal / oscillator output |
| پین 60 | VCAP — Internal 2.5 V core regulator bypass (decouple 1 µF + 100 nF) |
| پین 61 | MCLR — Master Clear / reset input, active-low |
| پین 62 | RC6 — Digital I/O port C bit 6 / TX1 EUSART |
| پین 63 | RC7 — Digital I/O port C bit 7 / RX1 EUSART |
| پین 64 | D+ — USB Full-Speed data D+ (with internal pull-up) |
کاربردهای معمول
PIC18F65J50T-I/PT مناسب است برای 6 کاربردs: USB HID Peripheral (Keyboard / Mouse / Custom HID), USB-to-UART Bridge (CDC Virtual COM Port), Industrial Sensor / LIN Slave Node, Home-Automation Bridge / IoT Edge Node, Consumer Audio / User-Interface Panel, Automotive Body Controller (AEC-Q100 application note).
USB HID Peripheral (Keyboard / Mouse / Custom HID)
The PIC18F65J50T-I/PT is a strong fit for USB Human Interface Device designs where 32 KB of Flash is enough for report descriptors and mainline code. Its integrated USB 2.0 Full-Speed device controller and 1.5 KB of dedicated USB buffer RAM eliminate the external PHY and let the MCU handle HID boot, report, and idle states in hardware. Paired with the MLA HID stack, designers reach a working prototype in days; the 48 MHz core delivers 16 MIPS for polling rates above 500 Hz with margin. The 54 I/O pins cover matrix-scanned keyboards up to 18x8 without a matrix-decoder IC.
پیشنهادی
USB-to-UART Bridge (CDC Virtual COM Port)
For legacy RS-232 replacement, the PIC18F65J50T-I/PT runs Microchip's CDC class driver in roughly 12 KB of Flash, leaving 20 KB for application logic. The two EUSART blocks provide RS-232/RS-485 interfaces up to 5 Mbit/s while USB enumerates as a COM port on the host. The 48 MHz core and 16 MIPS throughput sustain 921600 baud throughput without interrupt overflow, and the industrial -40 °C to +85 °C range suits factory-floor gateways. The 64-pin TQFP exposes enough I/O to add status LEDs, RTS/CTS, and Modbus DE/RE pins without a second MCU.
پیشنهادی
Industrial Sensor / LIN Slave Node
The PIC18F65J50T-I/PT powers cost-sensitive LIN (Local Interconnect Network) slave nodes for automotive body and industrial sensor applications. Its LIN-capable EUSART plus on-chip 10-bit ADC and two analog comparators handle analog signal conditioning in firmware while the master polls over LIN. The nanoWatt deep-sleep mode drops quiescent current to roughly 25 nA typical, critical for always-on sensors that must wake on a LIN header. The 54 I/O drive LED status, relay coils, and 4-20 mA loops without external buffers in many designs.
پیشنهادی
Home-Automation Bridge / IoT Edge Node
For smart-home gateways and IoT edge nodes, the PIC18F65J50T-I/PT integrates USB (host config PC), MI²C sensors, SPI radios, and a UART debug port on one chip. The MI²C block talks to temperature, light, and motion sensors while the SPI bus drives sub-GHz transceivers at 10 Mbit/s. The nanoWatt sleep modes support battery-powered motion sensors that wake on interrupt, and the 32 KB Flash fits OTA bootloader plus ZigBee/Wi-Fi control logic. Designers migrate easily to the 80-pin PIC18F85J50 when extra I/O is needed without changing toolchain.
پیشنهادی
Consumer Audio / User-Interface Panel
The PIC18F65J50T-I/PT drives capacitive-touch user-interface panels and LED rings in consumer audio equipment, headphones, and smart speakers. Its 54 I/O drive up to 54 LEDs via Charlieplexing without external LED drivers, while 16 MIPS throughput runs smooth LED animations and basic audio DSP. The two EUSART blocks expose Bluetooth HCI to external BT modules, and the MI²C port connects to audio CODECs for volume and tone control. Industrial temperature grade covers headset and charger designs that must survive in-pocket heat.
پیشنهادی
Automotive Body Controller (AEC-Q100 application note)
The PIC18F65J50T-I/PT handles non-safety body-control functions like mirror adjust, interior lighting, and door modules where AEC-Q100 is desirable but a Q1 suffix is not mandatory. Its LIN-capable EUSART enables LIN-slave communication with the body controller, while the 10-bit ADC reads battery voltage and switch inputs with debouncing in firmware. The nanoWatt deep-sleep mode (about 25 nA typical) keeps quiescent draw well below 100 µA on parked vehicles. For AEC-Q100-mandated safety functions, designers step up to the PIC18F66J55-I/PT sibling or Q1-qualified members of the family.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای PIC18F65J50T-I/PT — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | PIC18F65J50-I/PT | PIC18F66J55-I/PT | PIC18F66J50-I/PT | PIC18F67J50-I/PT | PIC18F65J11-I/PT |
|---|---|---|---|---|---|---|
| Package | TQFP-64 (PT) 10x10 mm | TQFP-64 (PT) 10x10 mm - same | TQFP-64 (PT) 10x10 mm - same | TQFP-64 (PT) 10x10 mm - same | TQFP-64 (PT) 10x10 mm - same | TQFP-64 (PT) 10x10 mm - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Program Memory | 32 KB | 32 KB | 96 KB | 64 KB | 128 KB | 32 KB |
| Data RAM | 3.8 KB | 3.8 KB | 3.8 KB | 3.8 KB | 3.8 KB | 3.8 KB |
| Maximum Clock Speed | 48 MHz (16 MIPS) | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| USB Full-Speed | Yes (device mode) | Yes | Yes | Yes | Yes | No (USB-free variant) |
| Packaging Suffix | Tape & Reel ("T") | Tray (no "T") | Tray | Tray | Tray | Tray |
| Operating Temperature | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C |
تفاوت‌های کلیدی
- Drop-in tray equivalent exists for prototype build (در مقابلPIC18F65J50-I/PT)
- 3x Flash upgrade path available in same package (در مقابلPIC18F66J55-I/PT)
- USB-free pinout cousin available (در مقابلPIC18F65J11-I/PT)
یادداشت‌های طراحی
Estimated: at VDD=3.3 V, all 54 I/O sourcing 10 mA into 50% capacitive loads at 48 MHz, the PIC18F65J50T-I/PT draws roughly 25-35 mA. Decouple VDD with 100 nF + 1 µF ceramic placed within 5 mm of pins 7, 17, 25; decouple AVDD with a 100 nF + 10 µF network within 5 mm of pin 40; decouple VCAP (pin 60) with a 1 µF + 100 nF low-ESR network per the family datasheet. Skip the internal regulator only if you have a clean external 2.5 V rail.
Place the 64-pin TQFP on a top-layer land pattern with 0.5 mm pitch and 0.6 mm pad length, fan out inner-row signals on inner layers, and use a continuous ground plane beneath the device. Keep the USB D+/D- (pins 64 and the corresponding USB pin on the 64-pin PT variant) as a 90 Ω differential pair with no stubs; place the 27 Ω series resistor and ferrite bead within 4 mm of the connector. Maintain 4 mm clearance between the analog AVCC/AVSS inputs and the switching D+/D- pair.
USB Full-Speed signal integrity on the PIC18F65J50T-I/PT depends on a 1.5 kΩ pull-up on D+ (full-speed) routed through the MCU's internal pull-up control register; engineers should select 'internal pull-up' via the UPUEN bit to keep BOM cost down. Add an external ESD array (e.g., USBLC6-2) right at the connector. Avoid running the SPI SCK above 10 MHz without source termination, and ensure that MCLR (pin 61) has a 10 kΩ pull-up and 100 nF to ground per the datasheet reset network.
Common pitfalls include (1) tying VUSB to 5 V when running VDD at 3.3 V, which violates absolute-maximum and damages the USB transceiver; tie VUSB to VDD; (2) forgetting the VCAP capacitor, which prevents the internal regulator from starting and results in a no-start condition; (3) using delay loops for USB timing rather than the on-chip USB clock, which causes enumeration failure; (4) omitting the 4.7 kΩ pull-up on MCLR during programming; (5) misconfiguring the PLL when moving from 8 MHz to 48 MHz, which locks the CPU. Always read the family datasheet section on oscillator configuration before bringing up the part.
Estimated: at room temperature, 48 MHz CPU, USB active, and 30 mA total supply, the 64-pin TQFP junction-to-ambient thermal resistance is approximately 50 °C/W per JEDEC EIA/JESD51 measurement, giving a 1.5 °C rise above ambient - well within the -40 °C to +85 °C industrial range. The TQFP-64 (PT) package does NOT require a heatsink in typical USB HID or CDC applications. If all 54 I/O source maximum current continuously, derate by 4 mA per output per the family datasheet DC characteristics table.
اطلاعات انطباق
RoHS-compliant per Microchip product page. Not AEC-Q100 qualified; designers requiring automotive qualification should consider AEC-Q100-qualified PIC18F family members. Halogen-free status not explicitly listed in verified web data.
