PIC24FJ512GU410-E/PT - 512KB Flash USB LCD MCU | Microchip
MPN: PIC24FJ512GU410-E/PT ✓ فعالPIC24FJ512GU410-E/PT نمای کلی
A 16-bit microcontroller (MCU) is a programmable processor with a 16-bit data path, instruction word, and register width. Within the embedded hierarchy it sits between 8-bit MCUs (lower cost, simpler peripherals) and 32-bit ARM Cortex-M MCUs (higher performance, richer ecosystems). The PIC24F family specifically targets ultra-low-power and mixed-signal applications, and the GU4/GL4 sub-family adds dual-partition Flash for live Over-The-Air (OTA) firmware updates without device downtime - a critical capability for connected products deployed in the field.
Key features include 512 KB of ECC-protected Flash supporting Dual Partition / EEPROM Emulation, 32 KB SRAM, a 14-channel 12-bit ADC, four I2C, four SPI, and five UART peripherals, plus a hardware Cryptographic Engine (AES, DES, 3DES, SHA, MD5, and RNG). Core-independent peripherals (CIPs) such as Configurable Logic Cells (CLC), Multiple Output Capture/Compare/PWM, and a 32-bit Real-Time Clock Calendar enable event-driven designs that minimize CPU wake-ups and reduce average power consumption below 1 uA in Deep Sleep mode.
The device's architecture combines a modified Harvard bus with a 16-bit instruction word and 24-bit instruction address space, giving a deterministic interrupt latency of 5 cycles. The full-speed USB 2.0 peripheral with integrated PHY supports HID, CDC, MSD, and Vendor classes without an external transceiver. The segmented LCD driver can directly control up to 480 pixels (8 commons x 60 segments) with internal charge pump and contrast bias generation, eliminating the need for an external LCD bias network.
Typical applications include low-power IoT sensor nodes with OTA firmware update capability, USB HID human-interface devices (keyboards, mice, touch panels), medical devices such as glucose meters and infusion pumps, industrial HMI panels with integrated LCD, secure authentication tokens using the on-chip AES engine, and home automation controllers with segmented displays. The wide operating temperature range of -40C to +125C (E suffix indicates Extended temperature grade) also supports outdoor and industrial deployments.
When designing with this device, allocate pin remapping carefully between the LCD segment bus and parallel master port functions - they share pins and cannot be used simultaneously. Ensure the dual-partition Flash bootloader (Boot-Secure mode) is provisioned before locking the configuration registers, and consider using the on-chip Crypto Engine to offload AES-256 from the CPU rather than implementing it in firmware.
This page synthesizes DigiKey/Mouser pricing, drop-in TQFP-100 alternatives from the PIC24FJ family, and practical low-power design notes that go beyond the manufacturer datasheet.
جایگزین‌های drop-in برای PIC24FJ512GU410-E/PT — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای PIC24FJ512GU410-E/PT (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در USB, Package, ADC, LCD Controller, Operating Temperature.
PIC24FJ512GU410-I/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC24FJ512GL410-I/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC24FJ512GL410-E/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC24FJ256GU410-I/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC24FJ256GU406-I/PT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PIC24FJ512GU410-E/PT حداکثر مقادیر مجاز و مشخصات الکتریکی
| Core Architecture | PIC24F (16-bit modified Harvard) |
| Program Memory (Flash) | 512 KB with ECC |
| Data EEPROM Emulation | Via dual-partition Flash |
| SRAM | 32 KB |
| Maximum CPU Speed | 32 MHz (16 MIPS) |
| Supply Voltage (VDD) | 2.0 V to 3.6 V |
| دمای کاری | -40 C to +125 C (Extended, E suffix) |
| ADC | 12-bit, up to 20 channels |
| USB | USB 2.0 Full-Speed with on-chip PHY |
| LCD Controller | Up to 480 segments (8 COM x 60 SEG) with charge pump |
| Crypto Engine | AES, DES, 3DES, SHA, MD5, RNG |
| UART / SPI / I2C | 5 UART / 4 SPI / 4 I2C |
| Timers | Multiple 16-bit and 32-bit timers |
| RTC | Real-Time Clock Calendar with VBAT retention |
| بسته‌بندی | 100-pin TQFP (PT), 12x12 mm |
| وضعیت RoHS | Compliant |
| نوع نصب | Surface Mount |
پیکربندی پین PIC24FJ512GU410-E/PT
| پین 1 | SDA3/RP17/PMD11/RF6 — I2C3 SDA / remappable peripheral / PMP data |
| پین 2 | SCL3/RP18/PMD10/RF5 — I2C3 SCL / remappable peripheral / PMP data |
| پین 3 | RP19/PMD9/RF4 — Remappable peripheral / PMP data |
| پین 4 | RP20/PMD8/RF3 — Remappable peripheral / PMP data |
| پین 5 | AN17/RP21/CN21/RG6 — Analog input / remappable peripheral / change notification |
| پین 6 | AN18/RP22/CN22/RG7 — Analog input / remappable peripheral / change notification |
| پین 7 | AN19/RP23/CN23/RG8 — Analog input / remappable peripheral / change notification |
| پین 8 | AN20/RP24/CN24/RG9 — Analog input / remappable peripheral / change notification |
| پین 9 | VSS — Ground reference |
| پین 10 | VDD — Positive supply voltage (2.0 V to 3.6 V) |
| پین 11 | SOSCI/RPC13 — Secondary oscillator input / remappable peripheral |
| پین 12 | SOSCO/RPC14 — Secondary oscillator output / remappable peripheral |
| پین 13 | RTCC/RP29 — Real-Time Clock Calendar output / remappable peripheral |
| پین 14 | VBAT — RTCC battery backup supply |
| پین 15 | RA0/AN0/CVD1 — Port A bit 0 / analog input / CVD |
| پین 16 | RA1/AN1/CVD2 — Port A bit 1 / analog input / CVD |
| پین 17 | RA2/AN2 — Port A bit 2 / analog input |
| پین 18 | RA3/AN3 — Port A bit 3 / analog input |
| پین 19 | RA4/AN4 — Port A bit 4 / analog input |
| پین 20 | RA5/AN5 — Port A bit 5 / analog input |
| پین 21 | RA6/AN6 — Port A bit 6 / analog input |
| پین 22 | RA7/AN7 — Port A bit 7 / analog input |
| پین 23 | VDD — Positive supply voltage |
| پین 24 | VSS — Ground reference |
| پین 25 | RB0/AN8 — Port B bit 0 / analog input |
| پین 26 | RB1/AN9 — Port B bit 1 / analog input |
| پین 27 | RB2/AN10 — Port B bit 2 / analog input |
| پین 28 | RB3/AN11 — Port B bit 3 / analog input |
| پین 29 | RB4/AN12 — Port B bit 4 / analog input |
| پین 30 | RB5/AN13 — Port B bit 5 / analog input |
| پین 31 | RB6/AN14 — Port B bit 6 / analog input |
| پین 32 | RB7/AN15 — Port B bit 7 / analog input |
| پین 33 | RC1/T1CK — Port C bit 1 / Timer1 clock input |
| پین 34 | RC2/AN16 — Port C bit 2 / analog input |
| پین 35 | RC3/AN21 — Port C bit 3 / analog input |
| پین 36 | RC4/AN22 — Port C bit 4 / analog input |
| پین 37 | VDD — Positive supply voltage |
| پین 38 | VSS — Ground reference |
| پین 39 | RD0 — Port D bit 0 |
| پین 40 | RD1 — Port D bit 1 |
| پین 41 | RD2 — Port D bit 2 |
| پین 42 | RD3 — Port D bit 3 |
| پین 43 | RD4 — Port D bit 4 |
| پین 44 | RD5 — Port D bit 5 |
| پین 45 | RD6 — Port D bit 6 |
| پین 46 | RD7 — Port D bit 7 |
| پین 47 | RE0 — Port E bit 0 |
| پین 48 | RE1 — Port E bit 1 |
| پین 49 | RE2 — Port E bit 2 |
| پین 50 | RE3 — Port E bit 3 |
| پین 51 | RE4 — Port E bit 4 |
| پین 52 | RE5 — Port E bit 5 |
| پین 53 | RE6 — Port E bit 6 |
| پین 54 | RE7 — Port E bit 7 |
| پین 55 | RF0 — Port F bit 0 |
| پین 56 | RF1 — Port F bit 1 |
| پین 57 | RG2 — Port G bit 2 |
| پین 58 | RG3 — Port G bit 3 |
| پین 59 | VDD — Positive supply voltage |
| پین 60 | VSS — Ground reference |
| پین 61 | RH0 — Port H bit 0 |
| پین 62 | RH1 — Port H bit 1 |
| پین 63 | RH2 — Port H bit 2 |
| پین 64 | RH3 — Port H bit 3 |
| پین 65 | RH4 — Port H bit 4 |
| پین 66 | RH5 — Port H bit 5 |
| پین 67 | RH6 — Port H bit 6 |
| پین 68 | RH7 — Port H bit 7 |
| پین 69 | RJ0 — Port J bit 0 |
| پین 70 | RJ1 — Port J bit 1 |
| پین 71 | RJ2 — Port J bit 2 |
| پین 72 | RJ3 — Port J bit 3 |
| پین 73 | VDD — Positive supply voltage |
| پین 74 | VSS — Ground reference |
| پین 75 | D+ — USB D+ differential data line |
| پین 76 | D- — USB D- differential data line |
| پین 77 | VBUS — USB VBUS sensing input (5 V tolerant) |
| پین 78 | RC12/OSC1/CLKIN — Primary oscillator input / external clock input |
| پین 79 | RC15/OSC2/CLKOUT — Primary oscillator output / clock output |
| پین 80 | MCLR — Master clear reset input (active low) |
| پین 81 | RA8/INT1 — Port A bit 8 / external interrupt 1 |
| پین 82 | RA9/INT2 — Port A bit 9 / external interrupt 2 |
| پین 83 | RA10/INT3 — Port A bit 10 / external interrupt 3 |
| پین 84 | RA11/INT4 — Port A bit 11 / external interrupt 4 |
| پین 85 | RB8 — Port B bit 8 |
| پین 86 | RB9 — Port B bit 9 |
| پین 87 | RB10 — Port B bit 10 |
| پین 88 | RB11 — Port B bit 11 |
| پین 89 | RB12 — Port B bit 12 |
| پین 90 | RB13 — Port B bit 13 |
| پین 91 | RB14 — Port B bit 14 |
| پین 92 | RB15 — Port B bit 15 |
| پین 93 | VSS — Ground reference |
| پین 94 | VDD — Positive supply voltage |
| پین 95 | RG0 — Port G bit 0 |
| پین 96 | RG1 — Port G bit 1 |
| پین 97 | RG12 — Port G bit 12 |
| پین 98 | RG13 — Port G bit 13 |
| پین 99 | RG14 — Port G bit 14 |
| پین 100 | RG15 — Port G bit 15 |
کاربردهای معمول
PIC24FJ512GU410-E/PT مناسب است برای 6 کاربردs: Low-Power IoT Sensor Nodes with OTA Firmware Updates, USB HID Human-Interface Devices, Medical Devices with Integrated LCD, Industrial HMI Panels with Segmented LCD, Secure Authentication Tokens, Home Automation Controllers with Display.
Low-Power IoT Sensor Nodes with OTA Firmware Updates
The PIC24FJ512GU410-E/PT is an excellent fit for battery-powered IoT sensor nodes that require reliable over-the-air firmware updates in the field. Its 512 KB Dual Partition Flash supports live A/B firmware swap so devices stay connected during updates, and the integrated USB 2.0 Full-Speed PHY simplifies direct-to-USB provisioning via USB-C or Micro-B connectors. The hardware Cryptographic Engine offloads AES-256 and SHA verification, reducing CPU wake time and average power consumption - the device consumes well under 100 uA average in Deep Sleep with RTCC retention. Engineers commonly pair it with sub-GHz transceivers or BLE modules over UART/SPI for full-stack sensor-node designs.
پیشنهادی
USB HID Human-Interface Devices
The PIC24FJ512GU410-E/PT serves as a USB HID controller in keyboards, mice, touch panels, and industrial control surfaces thanks to its integrated USB 2.0 Full-Speed PHY and 32 KB of RAM for HID report buffers. The 32 MIPS core provides ample headroom for matrix-scanning debouncing, multi-touch gesture detection, and RGB backlight control. Five UART peripherals support external wireless receivers (Bluetooth dongles), while the 12-bit ADC handles analog joysticks or potentiometer inputs. The 100-pin TQFP provides enough GPIO for large keyboard matrices (8x16 or more) without external I/O expanders.
پیشنهادی
Medical Devices with Integrated LCD
The PIC24FJ512GU410-E/PT is well suited to medical products such as glucose meters, infusion pumps, and patient monitors where the integrated 480-segment segmented LCD controller eliminates external display drivers. The on-chip LCD charge pump provides bias for high-contrast direct-drive displays even from a single 3 V battery. The hardware AES-256 engine and secure Dual Partition OTA boot enable HIPAA-friendly firmware integrity verification and authenticated wireless updates. The -40 C to +125 C extended temperature range supports storage and operational requirements of medical-grade equipment.
پیشنهادی
Industrial HMI Panels with Segmented LCD
In industrial HMI panels and operator interfaces, the PIC24FJ512GU410-E/PT combines a 480-segment LCD controller, 12-bit ADC for analog sensor inputs (4-20 mA loops, thermistors), and hardware crypto for secure field commissioning. The 100-pin TQFP provides GPIO for matrix keypads, LED indicators, and isolated serial interfaces. Four SPI and four I2C channels support external isolated transceivers for RS-485 Modbus or CAN connectivity. The Extended temperature grade and ECC Flash make it attractive for factory-floor controllers that must run reliably for years.
پیشنهادی
Secure Authentication Tokens
The PIC24FJ512GU410-E/PT's hardware Cryptographic Engine (AES, DES, 3DES, SHA-256, MD5, and RNG) makes it a strong choice for hardware authenticators and secure key-fob devices. The integrated USB Full-Speed PHY supports USB HID or CCID smartcard-class devices without external bridge chips. Dual Partition Flash with secure boot allows safe firmware upgrades while preventing rollback attacks. The 32 KB SRAM accommodates TLS handshake scratch memory for low-overhead authentication protocols in IoT gateways and access control readers.
پیشنهادی
Home Automation Controllers with Display
Home automation hubs, smart thermostats, and appliance controllers benefit from the PIC24FJ512GU410-E/PT's combination of segmented LCD driver, USB connectivity, and low-power Deep Sleep modes. The device can stay connected to a wireless transceiver over UART or SPI while maintaining the segmented LCD user interface at near-zero standby power. Dual Partition OTA lets manufacturers push new feature updates or security patches to deployed thermostats without service calls. Five UART ports allow simultaneous connections to Wi-Fi, BLE, sub-GHz, and Zigbee modules.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای PIC24FJ512GU410-E/PT — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | PIC24FJ512GU410-I/PT | PIC24FJ512GL410-I/PT | PIC24FJ512GL410-E/PT | PIC24FJ256GU410-I/PT | PIC24FJ256GU406-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-100 (PT) 12x12 mm | TQFP-100 (PT) 12x12 mm - same | TQFP-100 (PT) 12x12 mm - same | TQFP-100 (PT) 12x12 mm - same | TQFP-100 (PT) 12x12 mm - same | TQFP-100 (PT) 12x12 mm - same |
| Flash Memory | 512 KB | 512 KB | 512 KB | 512 KB | 256 KB (-50%) | 256 KB (-50%) |
| SRAM | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| CPU Speed | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS |
| USB | USB 2.0 Full-Speed with PHY | USB 2.0 Full-Speed with PHY | USB 2.0 Full-Speed with PHY | USB 2.0 Full-Speed with PHY | USB 2.0 Full-Speed with PHY | USB 2.0 Full-Speed with PHY |
| Crypto Engine | AES, DES, 3DES, SHA, MD5, RNG | AES, DES, 3DES, SHA, MD5, RNG | Not included | Not included | AES, DES, 3DES, SHA, MD5, RNG | AES, DES, 3DES, SHA, MD5, RNG |
| LCD Segments | Up to 480 segments (8x60) | Up to 480 segments | Up to 480 segments | Up to 480 segments | Up to 480 segments | Reduced LCD segment count |
| Temperature Grade | Extended -40 C to +125 C (E) | Industrial -40 C to +85 C (I) | Industrial -40 C to +85 C (I) | Extended -40 C to +125 C (E) | Industrial -40 C to +85 C (I) | Industrial -40 C to +85 C (I) |
تفاوت‌های کلیدی
- Higher operating temperature range for industrial deployments (در مقابلPIC24FJ512GU410-I/PT)
- On-chip hardware Cryptographic Engine (در مقابلPIC24FJ512GL410-I/PT)
- Larger Flash memory for OTA firmware space (در مقابلPIC24FJ256GU410-I/PT)
یادداشت‌های طراحی
Power supply decoupling for the PIC24FJ512GU410-E/PT requires a 100 nF ceramic capacitor placed within 3 mm of each VDD pin pair, plus a single 4.7 uF bulk capacitor near the device, per Microchip PIC24FJ family hardware design notes. The USB VBUS pin requires its own 4.7 uF bulk capacitor to supply transient current during USB events. Place a 10 kohm pull-up on MCLR if not driven by an external supervisor, and ensure the VBAT pin connects to a backup battery or to VDD through a low-leakage diode if RTCC retention is required during main power loss.
USB D+ and D- traces must be routed as a 90-ohm differential pair with matched length (delta < 2 mm) and a continuous ground reference plane beneath them, per USB 2.0 High-Speed layout guidelines. The 100-pin TQFP package benefits from a 4-layer PCB with a dedicated ground plane to reduce EMI and to provide thermal relief for the 1.0 W to 1.5 W maximum power dissipation. Decoupling capacitors should use vias placed as close to the VDD/VSS pads as possible, ideally with multiple vias to reduce parasitic inductance.
A common pitfall when designing with the PIC24FJ512GU410-E/PT is forgetting that LCD segment pins are multiplexed with other peripherals - selecting an LCD function reassigns the corresponding GPIO. Also, the Dual Partition OTA bootloader requires configuration bits and table reads in the IVT before locking the config; doing it out of order can brick the device. When migrating from the I-grade to E-grade variant, verify that your crystal oscillator's ESR is within the E-grade's tighter tolerance, and check that all analog references account for the wider -40 C to +125 C temperature swing.
اطلاعات انطباق
RoHS and REACH compliant per Microchip product page; not AEC-Q100 qualified - choose PIC24FJ512GB610 or similar AEC-Q100 PIC24FJ parts for automotive. Halogen-free per Microchip environmental compliance documentation.
