R5F100SJAFB#30 - 32MHz 256KB RL78/G13 MCU | Renesas
MPN: R5F100SJAFB#30 ✓ فعالR5F100SJAFB#30 نمای کلی
A microcontroller is a programmable semiconductor that integrates a CPU core, memory, peripherals, and input/output interfaces on one device. The RL78/G13 belongs to the Renesas RL78 family of low-power embedded microcontrollers, combining 16-bit processing efficiency with energy-focused operation. This makes the R5F100SJAFB#30 suitable for products that need deterministic control, compact firmware support, and low standby consumption without adopting a larger application-processor architecture.
The R5F100SJAFB#30 provides 256 KB of flash memory organized as 256K x 8. According to the Renesas product page, the device includes an on-chip oscillator, data flash, and an A/D converter. These integrated resources can reduce external component count in appliance, industrial-control, and embedded equipment designs. The 32 MHz operating rate provides 43.2 DMIPS of computational performance, while the 66 uA/MHz active-current figure supports energy-efficient control loops.
The 128-LFQFP package provides a substantial pin count for an embedded controller, supporting integration of multiple I/O functions and analog interfaces on a conventional leaded surface-mount footprint. The -40°C to +85°C operating range suits industrial and consumer equipment requiring operation across extended ambient temperatures. The manufacturer also identifies hardware-operation detection functions that support household-appliance safety standards, although complete compliance for a finished product must be evaluated at the system level.
Typical uses include compact appliance controllers, industrial sensors, motor and relay-control systems, metering equipment, and low-power embedded products. In these applications, the MCU can execute control logic, sample analog signals through its A/D converter, retain configuration in flash, and enter STOP mode during idle periods. The 230 nA STOP-mode current is particularly useful when reducing standby energy in battery-assisted or intermittently powered systems.
PCB implementation requires a 128-pin land pattern, decoupling close to the supply pins, and careful handling of analog and clock signals. Firmware, peripheral configuration, and interrupt behavior should be validated against the device's electrical characteristics and application guidance before production. The principal engineering trade-off is the relatively large 14 x 20 mm package versus smaller MCU options, balanced by its generous pin count and integrated control resources.
This page consolidates the verified product identity, core specifications, application guidance, design considerations, and replacement-screening information for engineers evaluating the R5F100SJAFB#30. Use the manufacturer datasheet for the authoritative pin descriptions, timing diagrams, electrical limits, and complete peripheral configuration.
جایگزینهای drop-in برای R5F100SJAFB#30 — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
هیچ جایگزین مستقیمی برای این محصول موجود نیست.
درخواست جایگزینR5F100SJAFB#30 حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | 16-bit Microcontroller Unit (MCU) |
| Product Family | RL78/G13 |
| Maximum CPU Frequency | 32 MHz |
| Core Performance | 43.2 DMIPS |
| Flash Memory | 256 KB (256K x 8) |
| CPU Current Consumption | 66 uA/MHz |
| STOP Mode Current Consumption | 230 nA |
| On-Chip Oscillator | Yes |
| Data Flash | Yes |
| A/D Converter | Yes |
| Hardware Operation Detection | Yes |
| محدوده دمای کاری | -40°C to +85°C |
| بستهبندی | 128-LFQFP (14 x 20 mm) |
| تعداد پایه | 128 pins |
| نوع نصب | Surface Mount |
راهنمای پیکربندی پین R5F100SJAFB#30 128-lfqfp (14 x 20 mm)
پیکربندی پین برای R5F100SJAFB#30 (پکیج 128-lfqfp (14 x 20 mm)). این IC دیجیتال شامل GPIO، رابطهای ارتباطی (UART، SPI، I2C) و پینهای تغذیه است. برای عملکردهای جایگزین پین و گزینههای پیکربندی به دیتاشیت سازنده مراجعه کنید. ضروری برای طراحی سیستمهای نهفته و چیدمان PCB.
داده پینآوت تفصیلی موجود نیست برای R5F100SJAFB#30.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
R5F100SJAFB#30 مناسب است برای 6 کاربردs: Household Appliance Control, Industrial Sensor Interface, Motor and Relay Control, Battery-Powered Metering, Programmable Logic Controller, Data Logger and Environmental Monitor.
Household Appliance Control
The R5F100SJAFB#30 fits appliance-control boards that combine sequencing, user-input handling, temperature or level sensing, and low-power standby behavior. Its 32 MHz RL78/G13 core provides 43.2 DMIPS for responsive control logic, while the integrated A/D converter supports analog sensor inputs without a separate converter. The 128-pin LQFP package offers extensive I/O for displays, relays, buttons, and communication peripherals. Its 230 nA STOP-mode current helps minimize standby energy, although the final appliance power budget must include sensors, drivers, regulators, and communication hardware. The -40°C to +85°C range supports industrial environments and room-temperature appliance designs.
Industrial Sensor Interface
The R5F100SJAFB#30 is appropriate for sensor nodes that combine analog measurement, local configuration, and a compact embedded controller. The on-chip A/D converter can process inputs from resistive, voltage, or current-based sensors, while data flash can retain calibration values, thresholds, and device settings. Operating at up to 32 MHz gives the firmware capacity for filtering, diagnostics, and communication tasks. The 66 uA/MHz CPU specification is useful when average current matters, and the 230 nA STOP figure supports duty-cycled operation between measurement intervals. Board-level EMC performance still depends on sensor grounding, input protection, shielding, and power-supply design.
Motor and Relay Control
The R5F100SJAFB#30 can serve as the supervisory controller in relay, solenoid, and small-motor systems because its 128-pin LQFP package provides a large selection of general-purpose I/O pins. At 32 MHz and 43.2 DMIPS, the RL78/G13 core can execute motor-state logic, interlocks, timing, and diagnostics while coordinating multiple output functions. Hardware-operation detection adds a useful basis for monitoring abnormal device behavior. Suitable protection circuits, snubber networks, flyback components, and isolation must still be selected according to the inductive load and wiring environment, since the MCU should not switch high-energy loads directly without appropriate driver circuitry.
Battery-Powered Metering
The R5F100SJAFB#30 suits metering and portable measurement equipment where periodic wake-up and long inactive periods are common. Its 230 nA STOP-mode current provides a low baseline for energy conservation, while the 66 uA/MHz CPU figure supports efficient active measurement cycles. The 256 KB flash capacity is useful for firmware, event logs, configuration profiles, and calibration algorithms, and the integrated A/D converter supports analog front-end sampling. Practical battery life depends on the sensor, display, radio, regulator efficiency, and wake-up interval rather than MCU consumption alone. A duty-cycled firmware architecture can further reduce system energy.
Programmable Logic Controller
The R5F100SJAFB#30 can function as the central controller of a compact programmable logic or machine-control module. Its 32 MHz processing rate and 43.2 DMIPS performance accommodate sequencing, input scanning, output updates, diagnostics, and communication protocols. The 128-pin package accommodates more interface signals than a compact small-outline MCU, while the -40°C to +85°C range supports industrial operating conditions. For safety-related or electrically noisy machinery, the complete design should include appropriate input filtering, output isolation, watchdog strategy, reset design, and protective enclosures. Firmware development should follow the RL78/G13 peripheral and interrupt guidance in the manufacturer documentation.
Data Logger and Environmental Monitor
The R5F100SJAFB#30 supports environmental monitoring products that sample sensors, store measurements, and wake periodically for data transfer. Its 256 KB flash provides room for firmware and local buffered records, while data flash can hold configuration or calibration parameters. The 32 MHz core supports time stamping, filtering, unit conversion, and protocol formatting, and the A/D converter handles suitable analog sensor channels. The STOP-mode current of 230 nA is helpful when the device spends most of its time idle between samples. Storage endurance, write timing, sensor accuracy, and system-level power consumption should be evaluated before assigning long recording intervals.
دادههای مرجع مهندسی برای R5F100SJAFB#30 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول |
|---|---|
| Brand | Renesas Electronics |
| Package | 128-LFQFP (14 x 20 mm) |
| Product Family | RL78/G13 |
| CPU Architecture | 16-bit |
| Maximum CPU Frequency | 32 MHz |
| Core Performance | 43.2 DMIPS |
| Flash Memory | 256 KB (256K x 8) |
| CPU Current Consumption | 66 uA/MHz |
| STOP Mode Current Consumption | 230 nA |
| Operating Temperature Range | -40°C to +85°C |
| Integrated Peripherals | On-chip oscillator, data flash, A/D converter |
تفاوتهای کلیدی
- High core performance for a 16-bit low-power MCU (در مقابلR5F100SJAFB#X0)
- Generous memory and I/O capacity (در مقابلR5F100SJAFB#X0)
- Low-power operation across active and standby modes (در مقابلR5F100SJAFB#X0)
یادداشتهای طراحی
Implement the 128-LFQFP footprint with a pin-1 mark and verify pad dimensions against the Renesas package drawing before releasing artwork. Place all required supply bypass capacitors close to their associated power pins, with the shortest possible return path through the ground plane. Because the package provides many external connections, review every no-connect and unused-pin assignment against the datasheet pin table rather than inferring function from position.
Design the supply rail to satisfy the MCU's specified voltage and timing limits across the full -40°C to +85°C range. Confirm the regulator's startup behavior, load transient response, and current margin before relying on the 66 uA/MHz CPU figure. For low-power products, isolate loads that remain active during STOP mode, because the MCU's 230 nA specification does not include sensor, regulator, pull-up, or communication-circuit consumption.
Keep analog sensor inputs away from switching nodes, high-current relay paths, and fast digital edges. Use a continuous ground reference beneath the MCU where practical, and route sensitive input traces away from clock and PWM signals. The integrated A/D converter does not eliminate the need for careful grounding, input filtering, source impedance management, and calibration; confirm the permitted source impedance and sampling requirements in the manufacturer documentation.
Do not treat a similar RL78/G13 order code as a drop-in replacement without comparing package pinout, memory size, pin multiplexing, electrical limits, and temperature grade. Likewise, do not assume the 32 MHz CPU rate is appropriate for every peripheral operation; clock dividers, peripheral constraints, and firmware timing requirements still apply. Validate reset behavior, brownout handling, watchdog use, and flash-write timing in the final power and operating environment.
اطلاعات انطباق
The Renesas product page states that hardware-operation detection supports household-appliance safety standards, but device-specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations are not stated in the accessible product records.