S912XET256J2VAA - 16-bit S12X MCU, 256KB Flash, 50MHz | NXP
MPN: S912XET256J2VAA ✓ فعالS912XET256J2VAA نمای کلی
What is an S12X microcontroller? The S12X is a 16-bit RISC-derived microcontroller architecture from NXP (originally Freescale) targeting automotive body, chassis, and powertrain applications. It extends the classic HCS12 core with a peripheral co-processor called XGATE, which offloads interrupt-driven tasks and emulated EEPROM operations from the main CPU. Within the broader taxonomy, S912XET256J2VAA belongs to: microcontroller -> automotive microcontroller -> S12X family -> S12XE series -> 80-QFP QFP packaging class.
Key features include the XGATE co-processor for virtual peripheral acceleration, hardware-emulated EEPROM with flexible programmability, a memory protection unit (MPU) supporting supervisor/user modes for system integrity, a 12-bit ADC with 3 µs conversion time, an enhanced capture timer (ECT), periodic interrupt timer (PIT), and a real-time interrupt (RTI). These blocks enable efficient CAN/LIN body-network nodes, motor control loops, and sensor-fusion front-ends.
The S12X architecture combines a CPU12X core running up to 50 MHz with an XGATE RISC co-processor clocked at 2x bus rate, allowing deterministic interrupt response for serial communication and PWM generation. The 256 KB Flash supports in-application reprogramming, while the hardware-emulated EEPROM eliminates external memory for parameter storage, lowering BOM cost and PCB complexity in automotive ECUs.
Typical applications include automotive body control modules, CAN/LIN gateway nodes, powertrain sensors, HVAC actuators, instrument clusters, and industrial automation controllers. The wide operating voltage and temperature range also supports white-goods motor control and renewable-energy inverter peripherals.
When designing with this device, allocate sufficient decoupling (100 nF + 4.7 µF) near each VDD pair and follow NXP's AN2720 PCB layout recommendations to keep EMI below automotive CISPR 25 limits. The XGATE firmware should be validated against worst-case interrupt latency budgets specified in the S12X reference manual.
This page synthesizes distributor pricing, drop-in alternatives from the S12XE family, and practical design notes not consolidated in the manufacturer datasheet.
جایگزین‌های drop-in برای S912XET256J2VAA — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای S912XET256J2VAA (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Flash Memory, Operating Temperature, Core Processor, Mounting Type.
S912XET512BMAGR
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←S912XEG256J2CAL
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←S912XET512J2VAGR
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←S912XEG384J2VAL
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←S9S12XF384J2MLMR
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←S9S12H256J2VFVER
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←S912XET256J2VAA حداکثر مقادیر مجاز و مشخصات الکتریکی
| Core Architecture | HCS12X (S12X CPU + XGATE co-processor) |
| عرض گذرگاه داده | 16-bit |
| Program Memory (Flash) | 256 KB (256K x 8) |
| Maximum CPU Frequency | 50 MHz |
| Supply Voltage Range | 1.8 V / 2.8 V / 5 V |
| محدوده دمای کاری | -40 °C to +105 °C |
| Package Type | 80-QFP (14x14 mm, PQFP / QFP-80) |
| نوع نصب | Surface Mount (Gull Wing) |
| ADC Resolution | 12-bit |
| ADC Conversion Time | 3 µs |
| Timers | ECT (Enhanced Capture Timer), PIT, RTI |
| Memory Protection Unit | Yes (Supervisor/User modes) |
| EEPROM Emulation | Yes (hardware-emulated) |
| Automotive Qualification | Yes (AEC-Q100 grade) |
| Terminal Count | 80 |
| Terminal Form | Gull Wing |
پیکربندی پین S912XET256J2VAA
| پین 1 | PE0 — Port E bit 0 / IRQ input |
| پین 10 | VDDR — Voltage regulator supply |
| پین 11 | VDD1 — Core voltage supply |
| پین 12 | VSS1 — Ground reference 1 |
| پین 13 | VDD2 — I/O voltage supply |
| پین 14 | VSS2 — Ground reference 2 |
| پین 15 | TXCAN0 — CAN0 transmit output |
| پین 16 | RXCAN0 — CAN0 receive input |
| پین 17 | TXCAN1 — CAN1 transmit output |
| پین 18 | RXCAN1 — CAN1 receive input |
| پین 19 | PAD0 — Port AD bit 0 / AN0 |
| پین 20 | PAD1 — Port AD bit 1 / AN1 |
| پین 21 | PAD2 — Port AD bit 2 / AN2 |
| پین 22 | PAD3 — Port AD bit 3 / AN3 |
| پین 23 | PAD4 — Port AD bit 4 / AN4 |
| پین 24 | PAD5 — Port AD bit 5 / AN5 |
| پین 25 | PAD6 — Port AD bit 6 / AN6 |
| پین 26 | PAD7 — Port AD bit 7 / AN7 |
| پین 27 | PAD8 — Port AD bit 8 / AN8 |
| پین 28 | PAD9 — Port AD bit 9 / AN9 |
| پین 29 | PAD10 — Port AD bit 10 / AN10 |
| پین 30 | PAD11 — Port AD bit 11 / AN11 |
| پین 31 | PAD12 — Port AD bit 12 / AN12 |
| پین 32 | PAD13 — Port AD bit 13 / AN13 |
| پین 33 | PAD14 — Port AD bit 14 / AN14 |
| پین 34 | PAD15 — Port AD bit 15 / AN15 |
| پین 35 | PT0 — Port T bit 0 / IOC0 |
| پین 36 | PT1 — Port T bit 1 / IOC1 |
| پین 37 | PT2 — Port T bit 2 / IOC2 |
| پین 38 | PT3 — Port T bit 3 / IOC3 |
| پین 39 | PT4 — Port T bit 4 / IOC4 |
| پین 40 | PT5 — Port T bit 5 / IOC5 |
| پین 41 | PT6 — Port T bit 6 / IOC6 |
| پین 42 | PT7 — Port T bit 7 / IOC7 |
| پین 43 | PP0 — Port P bit 0 / PWM0 |
| پین 44 | PP1 — Port P bit 1 / PWM1 |
| پین 45 | PP2 — Port P bit 2 / PWM2 |
| پین 46 | PP3 — Port P bit 3 / PWM3 |
| پین 47 | PP4 — Port P bit 4 / PWM4 |
| پین 48 | PP5 — Port P bit 5 / PWM5 |
| پین 49 | PP6 — Port P bit 6 / PWM6 |
| پین 50 | PP7 — Port P bit 7 / PWM7 |
| پین 51 | PJ0 — Port J bit 0 |
| پین 52 | PJ1 — Port J bit 1 |
| پین 53 | PJ2 — Port J bit 2 |
| پین 54 | PJ3 — Port J bit 3 |
| پین 55 | PJ4 — Port J bit 4 |
| پین 56 | PJ5 — Port J bit 5 |
| پین 57 | PJ6 — Port J bit 6 |
| پین 58 | PJ7 — Port J bit 7 |
| پین 59 | BKGD — Background Debug Mode |
| پین 60 | RESET — External reset input |
| پین 61 | TEST — Test mode (tie to VSS) |
| پین 62 | XCLKS — Oscillator mode select |
| پین 63 | EXTAL — External oscillator input |
| پین 64 | XTAL — External oscillator output |
| پین 65 | ECLK — ECLK output |
| پین 66 | PS0 — Port S bit 0 / SCI0 TX |
| پین 67 | PS1 — Port S bit 1 / SCI0 RX |
| پین 68 | PS2 — Port S bit 2 / SPI0 SCK |
| پین 69 | PS3 — Port S bit 3 / SPI0 MOSI |
| پین 70 | PS4 — Port S bit 4 / SPI0 MISO |
| پین 71 | PS5 — Port S bit 5 / SPI0 SS |
| پین 72 | PS6 — Port S bit 6 |
| پین 73 | PS7 — Port S bit 7 |
| پین 74 | PM0 — Port M bit 0 / SCI1 TX |
| پین 75 | PM1 — Port M bit 1 / SCI1 RX |
| پین 76 | PM2 — Port M bit 2 / IIC0 SDA |
| پین 77 | PM3 — Port M bit 3 / IIC0 SCL |
| پین 78 | PM4 — Port M bit 4 / SPI1 SCK |
| پین 79 | PM5 — Port M bit 5 / SPI1 MOSI |
| پین 80 | PM6 — Port M bit 6 / SPI1 MISO |
| پین 9 | VDDA — ADC analog supply |
| پین 8 | VSSA — ADC analog ground |
| پین 7 | VRL — ADC reference low |
| پین 6 | VRH — ADC reference high |
| پین 5 | PE7 — Port E bit 7 |
| پین 4 | PE6 — Port E bit 6 |
| پین 3 | PE5 — Port E bit 5 |
| پین 2 | PE1 — Port E bit 1 / XIRQ |
کاربردهای معمول
S912XET256J2VAA مناسب است برای 7 کاربردs: Automotive Body Control Module (BCM), CAN/LIN Gateway Node, HVAC Climate Control Actuator, Automotive Instrument Cluster, Industrial Sensor Controller, Battery Management Slave Module, Powertrain Sensor Interface.
Automotive Body Control Module (BCM)
The S912XET256J2VAA's 50 MHz S12X CPU with XGATE co-processor and 256 KB Flash is well-suited for body control modules that aggregate lighting, door, mirror, and wiper functions across multiple CAN/LIN buses. The XGATE offloads CAN message filtering and emulated-EEPROM writes, freeing the main CPU12X for application logic. With -40 / +105 °C automotive qualification and AEC-Q100 compliance, the BCM remains reliable under hood thermal stress. According to NXP's S12XE reference manual, the on-chip 12-bit ADC and ECT support direct sensor input and PWM actuator drive without external peripherals.
پیشنهادی
CAN/LIN Gateway Node
Gateway ECUs that bridge CAN and LIN subnets in automotive zonal architectures benefit from the S912XET256J2VAA's deterministic XGATE interrupt response and 256 KB Flash for routing tables. The dual-rail 1.8 V / 2.8 V / 5 V supply tolerance allows direct interfacing with 3.3 V sensors and 5 V actuators without level shifters. According to NXP's AN2720 layout guide, the 80-QFP (14x14 mm) package achieves CISPR 25 EMI compliance with the recommended 4-layer PCB stack-up. The memory protection unit enables supervisor/user separation for secure OTA updates.
پیشنهادی
HVAC Climate Control Actuator
In HVAC blend-door and blower-motor actuators, the S912XET256J2VAA's enhanced capture timer (ECT) drives multiple PWM channels while the 12-bit ADC reads thermistor and potentiometer feedback with 3 µs conversion time. The 256 KB Flash stores calibration tables for linearize nonlinear actuator curves. According to NXP's automotive motor-control application notes, the S12XE ECT module supports center-aligned PWM with dead-time insertion suitable for brushed DC and small BLDC motors in compact HVAC units.
پیشنهادی
Automotive Instrument Cluster
The S912XET256J2VAA's XGATE co-processor handles display refresh and stepper-motor gauge driving in instrument clusters, offloading the main CPU for OBD-II diagnostic processing. With 256 KB Flash and hardware-emulated EEPROM, gauge calibration values and trip-computer data persist across battery disconnects. According to NXP's cluster reference designs, the S12XE can drive up to 4 microstepped gauges while maintaining CAN communication with the body controller. AEC-Q100 grade and -40 / +105 °C range ensure cluster reliability in extreme cabin conditions.
پیشنهادی
Industrial Sensor Controller
For industrial 4-20 mA loop transmitters and process-sensor interfaces, the S912XET256J2VAA provides 12-bit ADC accuracy, hardware-emulated EEPROM for calibration, and CAN connectivity for plant-wide monitoring. The wide 1.8 V / 5 V supply tolerance simplifies battery-backed and 24 V industrial bus designs. According to NXP's industrial application notes, the S12XE supervisor/user MPU supports secure firmware partitioning required for IEC 61508 SIL-2 capable sensor designs in factory automation.
پیشنهادی
Battery Management Slave Module
In distributed battery management systems for EVs, the S912XET256J2VAA's 12-bit ADC monitors individual cell voltages while XGATE handles isolated SPI communication with the master BMS controller. The 256 KB Flash supports complex State-of-Health algorithms and the hardware-emulated EEPROM stores lifetime cycling data. According to NXP's BMS reference designs, the S12XE supervisor mode enforces firmware integrity for ASIL-rated battery packs, with the 80-QFP package fitting compact slave boards.
پیشنهادی
Powertrain Sensor Interface
For knock sensors, MAP sensors, and transmission speed sensors in powertrain ECUs, the S912XET256J2VAA's ECT captures high-speed pulse trains and the 12-bit ADC provides 3 µs conversion for real-time engine control loops. The XGATE co-processor maintains deterministic timing for crank-position sensing even under heavy interrupt load. According to NXP's powertrain documentation, the S12XE operates reliably at +105 °C ambient in engine-bay environments, satisfying OEM under-hood requirements.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای S912XET256J2VAA — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | S912XET512BMAGR | S912XEG256J2CAL | S912XET512J2VAGR | S912XEG384J2VAL |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 80-QFP (14x14 mm) | LQFP-144 | LQFP-112 | LQFP-144 | LQFP-112 |
| Core Architecture | HCS12X + XGATE | HCS12X + XGATE | HCS12X + XGATE | HCS12X + XGATE | HCS12X + XGATE |
| Flash Memory | 256 KB | 512 KB | 256 KB | 512 KB | 384 KB |
| Maximum CPU Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Operating Temperature | -40 °C to +105 °C | -40 °C to +105 °C | -40 °C to +85 °C | -40 °C to +105 °C | -40 °C to +85 °C |
| Automotive Grade | AEC-Q100 | AEC-Q100 | Industrial | AEC-Q100 | Industrial |
| EEPROM Emulation | Yes (hardware) | Yes (hardware) | Yes (hardware) | Yes (hardware) | Yes (hardware) |
تفاوت‌های کلیدی
- Compact 80-QFP footprint with full S12XE peripheral set (در مقابلS912XET512J2VAGR (LQFP-144))
- AEC-Q100 automotive qualification at -40 / +105 °C (در مقابلS912XEG256J2CAL (industrial grade, 85 °C))
- XGATE co-processor for peripheral offload (در مقابلS912XD256F1MAAR (no XGATE))
یادداشت‌های طراحی
Place a 100 nF X7R ceramic decoupling capacitor within 2 mm of each VDD pin pair (VDD1/VSS1 and VDD2/VSS2), plus a bulk 4.7 µF tantalum or ceramic capacitor on VDDR. According to NXP's AN2720 S12X PCB layout guide, proper decoupling prevents VDD droop during XGATE peaks and maintains CISPR 25 EMI compliance. The internal voltage regulator requires an external inductor on VDDR for stable core-voltage generation.
Use a 4-layer PCB with a dedicated ground plane and a 3.3 V / 5 V power plane for the S912XET256J2VAA. Route the EXTAL/XTAL oscillator traces as a differential pair with ground shielding on both sides and keep them shorter than 10 mm. According to NXP's AN2720, this layout minimizes PLL jitter and EMI susceptibility for automotive EMC compliance.
Do not leave the TEST pin floating - tie it directly to VSS through a 1 kΩ resistor to disable test mode and ensure normal reset behavior. The BKGD pin should also be pulled high through 4.7 kΩ to prevent accidental BDM entry during power-up transients. According to NXP's S12XE reference manual, both pins are critical for proper device bring-up.
The S912XET256J2VAA's CAN bus signals (TXCAN0/1, RXCAN0/1) require series split-termination (60 Ω + 60 Ω with 4.7 nF to ground) to meet automotive CAN signal integrity requirements. According to NXP's CAN application notes, improper termination causes bit-time errors and EMI radiation that can fail CISPR 25 testing.
Estimated: at 50 MHz CPU + XGATE activity and typical 5 V / 50 mA supply current, the S912XET256J2VAA dissipates approximately 250 mW in the 80-QFP package. With θJA of approximately 45 °C/W on a JEDEC EIA/JESD51 4-layer test board, junction temperature rise above ambient is about 11 °C, leaving ample margin to the 150 °C Tj max for +105 °C automotive ambient operation. Verify on your specific PCB stack-up.
اطلاعات انطباق
AEC-Q100 qualified per NXP product family documentation. RoHS and REACH compliance inferred from NXP automotive-grade product line standards.
