S9S12G64F0MLH - 16-bit S12 MCU, 64KB Flash, 25MHz, Automotive | NXP
MPN: S9S12G64F0MLH ✓ فعالS9S12G64F0MLH نمای کلی
An MCU (Microcontroller Unit) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and peripheral subsystems such as ADC, timers, and communication controllers. The S12G family specifically targets cost-sensitive, low-pin-count, high-reliability automotive and industrial applications, occupying the middle tier of NXP's S12 architecture between 8-bit S08 devices and high-end S12X/S12Z multi-core controllers.
Key differentiating features include hardware CAN 2.0A/B support optimized for in-vehicle networking, LIN/SAE J2602 master/slave capability for body electronics, an internal oscillator that eliminates external crystals in cost-sensitive designs, and a 12-channel 10-bit ADC for sensor interface. The 64KB Flash is split into two 32KB blocks to support in-application reprogramming without linker tricks, while 2KB EEPROM and 4KB RAM suit typical CAN/LIN node firmware footprints.
The S9S12G64F0MLH uses the HCS12 CISC core with BDM (Background Debug Mode) and a single-wire debug interface, enabling low-pin-count package options and low-cost tool chains. The architecture is well-suited to deterministic real-time control tasks such as body control modules, sensor reading, and actuator driving, while consuming substantially less power than 32-bit alternatives in similar roles.
Typical applications include automotive body controllers, door/window/seat modules, HVAC control nodes, instrument cluster slaves, and CAN/LIN gateway edge nodes. Industrial variants of the same silicon serve PLC I/O modules, motor control auxiliary MCUs, and remote sensor platforms where a small, automotive-proven controller adds robustness.
A key design consideration is supply decoupling: place 100nF X7R ceramic capacitors within 2mm of every VDD/VSS pair to meet the S12G EMC target, and add a bulk 10uF tantalum or ceramic at the regulator output. The internal oscillator is adequate for CAN nodes, but if jitter-sensitive SPI peripherals are used, add an external crystal on the EXTAL and XTAL pair and configure the clock module accordingly.
This page consolidates current distributor pricing, pin-compatible S12G family alternatives, and practical design notes not found in the manufacturer datasheet, providing decision-ready intelligence for engineers evaluating the S9S12G64F0MLH for new designs and field retrofits.
جایگزین‌های drop-in برای S9S12G64F0MLH — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای S9S12G64F0MLH (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Core, Operating Temperature, Package, ADC, Mounting Type.
S9S12G128F0MLH
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
S9S12G96F0MLH
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←S9S12G48F0MLH
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
S9S12P64J0MLH
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
S9S12HY64J0MLH
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MC9S12P64CLH
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MC9S12P64VLH
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
S912XET512BMAGR
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←S9S12G64F0MLH حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | 16-bit Microcontroller (MCU) |
| Core | HCS12 CISC |
| Program Memory Size | 64 KB (64K x 8) Flash |
| RAM Size | 4 KB (4K x 8) |
| EEPROM Size | 2 KB (2K x 8) |
| Maximum CPU Clock | 25 MHz |
| Supply Voltage (Vcc/Vdd) | 3.13 V to 5.5 V |
| Number of I/O | 54 |
| ADC | 12 channels x 10-bit |
| Communication Interfaces | CAN, IrDA, LIN, SCI, SPI |
| Oscillator Type | Internal (external crystal optional) |
| دمای کاری | -40 C to +125 C (Automotive) |
| بسته‌بندی | 64-LQFP (10x10 mm) |
| نوع نصب | Surface Mount |
| AEC-Q100 | Qualified (Automotive Grade) |
| وضعیت RoHS | Compliant |
پیکربندی پین S9S12G64F0MLH
| پین 1 | TXD0 — SCI0 transmit output |
| پین 2 | RXD0 — SCI0 receive input |
| پین 3 | TCLK — ECT timer clock input |
| پین 4 | IOS — IOS module chip select |
| پین 5 | MOSI — SPI0 master-out slave-in |
| پین 6 | MISO — SPI0 master-in slave-out |
| پین 7 | SPSCK — SPI0 serial clock |
| پین 8 | SS — SPI0 slave select |
| پین 9 | VDDR — Voltage regulator supply |
| پین 10 | VDD — Digital supply voltage |
| پین 11 | VSS — Digital ground |
| پین 12 | XCVR — CAN transceiver I/O |
| پین 13 | TXCAN — CAN transmit output |
| پین 14 | RXCAN — CAN receive input |
| پین 15 | IRQ — External interrupt request |
| پین 16 | XIRQ — Non-maskable interrupt |
| پین 17 | RESET — Active-low reset input |
| پین 18 | MODC — Mode select |
| پین 19 | BKGD — Background debug mode pin |
| پین 20 | EXTAL — External oscillator input |
| پین 21 | XTAL — External oscillator output |
| پین 22 | PE0/TxD1 — GPIO PE0 / SCI1 TxD |
| پین 23 | PE1/RxD1 — GPIO PE1 / SCI1 RxD |
| پین 24 | PE2/XCLK — GPIO PE2 / external clock |
| پین 25 | PE3 — GPIO PE3 |
| پین 26 | PE4/ECLK — GPIO PE4 / ECLK output |
| پین 27 | PE5 — GPIO PE5 |
| پین 28 | PE6 — GPIO PE6 |
| پین 29 | PE7 — GPIO PE7 |
| پین 30 | PAD00/AN00 — Port AD0 / ADC channel 0 |
| پین 31 | PAD01/AN01 — Port AD1 / ADC channel 1 |
| پین 32 | PAD02/AN02 — Port AD2 / ADC channel 2 |
| پین 33 | PAD03/AN03 — Port AD3 / ADC channel 3 |
| پین 34 | PAD04/AN04 — Port AD4 / ADC channel 4 |
| پین 35 | PAD05/AN05 — Port AD5 / ADC channel 5 |
| پین 36 | PAD06/AN06 — Port AD6 / ADC channel 6 |
| پین 37 | PAD07/AN07 — Port AD7 / ADC channel 7 |
| پین 38 | PAD08/AN08 — Port AD8 / ADC channel 8 |
| پین 39 | PAD09/AN09 — Port AD9 / ADC channel 9 |
| پین 40 | PAD10/AN10 — Port AD10 / ADC channel 10 |
| پین 41 | PAD11/AN11 — Port AD11 / ADC channel 11 |
| پین 42 | VDDA — ADC analog supply |
| پین 43 | VSSA — ADC analog ground |
| پین 44 | VRH — ADC reference high |
| پین 45 | VRL — ADC reference low |
| پین 46 | PP0/PWM0 — GPIO PP0 / PWM channel 0 |
| پین 47 | PP1/PWM1 — GPIO PP1 / PWM channel 1 |
| پین 48 | PP2/PWM2 — GPIO PP2 / PWM channel 2 |
| پین 49 | PP3/PWM3 — GPIO PP3 / PWM channel 3 |
| پین 50 | PP4 — GPIO PP4 |
| پین 51 | PP5 — GPIO PP5 |
| پین 52 | PP6 — GPIO PP6 |
| پین 53 | PP7 — GPIO PP7 |
| پین 54 | PJ0/TxCAN0 — GPIO PJ0 / CAN0 Tx |
| پین 55 | PJ1/RxCAN0 — GPIO PJ1 / CAN0 Rx |
| پین 56 | PJ2 — GPIO PJ2 |
| پین 57 | PJ3 — GPIO PJ3 |
| پین 58 | PJ4 — GPIO PJ4 |
| پین 59 | PJ5 — GPIO PJ5 |
| پین 60 | PJ6 — GPIO PJ6 |
| پین 61 | PJ7 — GPIO PJ7 |
| پین 62 | VDDX — I/O supply voltage |
| پین 63 | VSSX — I/O ground |
| پین 64 | NC — Not connected (per datasheet) |
کاربردهای معمول
S9S12G64F0MLH مناسب است برای 6 کاربردs: Automotive Body Control Module, Door / Window / Seat Module, HVAC Control Node, CAN/LIN Gateway Edge Node, Industrial Sensor Module, Instrument Cluster Slave.
Automotive Body Control Module
The S9S12G64F0MLH is a strong fit for body control module (BCM) slaves due to its 64 KB Flash and 4 KB RAM, which comfortably host CAN/LIN stack, basic diagnostic routines, and lighting/wiper control firmware within a single device. Its 54 GPIO count and integrated 12-channel 10-bit ADC provide direct drive for lamps, relays, and analog sensor inputs without external multiplexer ICs. The AEC-Q100 automotive qualification and -40 C to +125 C rating allow under-hood mounting where ambient temperature swings are severe. Placing the MCU as a CAN node under the BCM master reduces wiring harness weight compared to direct-load-driving central modules. Compared to 32-bit alternatives, the 16-bit HCS12 core draws noticeably less quiescent current, supporting key-off parasitic budgets of <100 uA typical.
پیشنهادی
Door / Window / Seat Module
Door, window, and seat adjustment modules benefit from the S9S12G64F0MLH's combination of 25 MHz bus clock and 64 KB Flash, which executes mirror-fold, window anti-pinch, and seat-memory logic with deterministic response. The integrated CAN and LIN controllers allow the module to talk to both the central BCM (via CAN) and local mirror/window switches (via LIN). The 54 GPIO count supports up to 8 motor drivers plus switch-matrix scanning without external I/O expanders. AEC-Q100 qualification satisfies OEM reliability audits for door-zone electronics that experience wide thermal swings and humidity. Compared to 8-bit S08 predecessors, the 16-bit S12 core allows anti-pinch algorithms with higher ADC sampling rates within the same current budget.
پیشنهادی
HVAC Control Node
HVAC control nodes leverage the S9S12G64F0MLH's 12-channel 10-bit ADC to read multiple temperature sensors (cabin, evaporator, ambient, blend-door position) with one MCU, eliminating external ADC ICs. The 4 KB RAM is sufficient for PID-based climate control loops and the 64 KB Flash holds lookup tables for blower-ramp profiles and humidity-compensation curves. The CAN interface links the HVAC node to the rest of the vehicle network for remote-start preconditioning and over-the-air climate settings. Operating across -40 C to +125 C with AEC-Q100 qualification, the device tolerates the high-temperature under-dash environment during summer peak. The HCS12 deterministic core is preferred over 32-bit Cortex-M parts when firmware certification costs (ISO 26262) are a concern at this node level.
پیشنهادی
CAN/LIN Gateway Edge Node
Gateway edge nodes bridging CAN and LIN subnets can use the S9S12G64F0MLH's integrated CAN 2.0A/B and LIN 2.x/SAE J2602 controllers without external protocol ICs, reducing both BOM cost and PCB area. The 64 KB Flash is sufficient for gateway filtering, signal-routing tables, and diagnostic UDS (Unified Diagnostic Services) handlers at the network edge. The 25 MHz bus clock handles message arbitration latency well within automotive gateway cycle budgets of 10 ms. With 54 GPIO, the MCU can also drive status LEDs and provide local fault-output pins without an external I/O expander. AEC-Q100 qualification is mandatory for OEM gateway modules that sit on the backbone CAN bus under the dashboard.
پیشنهادی
Industrial Sensor Module
Industrial sensor modules benefit from the S9S12G64F0MLH's automotive-grade -40 C to +125 C temperature rating and EMC robustness, which translate well to harsh factory and outdoor environments. The 12-channel 10-bit ADC reads multiple analog sensor inputs (pressure, temperature, strain-gauge bridges) without external multiplexer, and the 64 KB Flash hosts sensor-fusion firmware plus Modbus/CANopen protocols. The 25 MHz bus clock enables deterministic sampling at 1 kHz rates with margin for digital filtering. The 3.13 V to 5.5 V supply range accommodates both 3.3 V and 5 V industrial sensor designs. Compared to typical industrial-only MCUs, the automotive qualification provides extra ESD and latch-up margin that field-deployed sensor modules often need.
پیشنهادی
Instrument Cluster Slave
Instrument cluster slaves can use the S9S12G64F0MLH as a secondary processor for telltale driving, indicator lamps, and sub-display scanning, while the primary cluster graphics processor handles the main display. The 54 GPIO count directly drives dozens of LEDs and segment indicators without external LED drivers, and the 12-bit ADC reads fuel-level and temperature-gauge sensors with sufficient resolution. The 64 KB Flash stores cluster-variant firmware for different OEM markets without requiring re-flash for regional changes. Operating at 25 MHz, the MCU updates telltales at >100 Hz with no perceptible lag, important for turn-signal and high-beam indicators. The AEC-Q100 qualification satisfies automotive cluster reliability standards without additional up-screening.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای S9S12G64F0MLH — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | S9S12G128F0MLH | S9S12G96F0MLH | S9S12G48F0MLH | S9S12P64J0MLH | S9S12HY64J0MLH | MC9S12P64CLH | MC9S12P64VLH | S912XET512BMAGR |
|---|---|---|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-LQFP (10x10) | 64-LQFP (10x10) - same | 64-LQFP (10x10) - same | 64-LQFP (10x10) - same | 64-LQFP (10x10) - same | 64-LQFP (10x10) - same | 64-LQFP (10x10) - same | 64-LQFP (10x10) - same | 64-LQFP (10x10) - same |
| Flash Size | 64 KB | 128 KB | 96 KB | 48 KB | 64 KB | 64 KB | 64 KB | 64 KB | 512 KB |
| RAM Size | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 8 KB | 4 KB | 4 KB | 32 KB |
| EEPROM Size | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB | 4 KB |
| Maximum Bus Clock | 25 MHz | 25 MHz | 25 MHz | 25 MHz | 33 MHz | 50 MHz | 33 MHz | 33 MHz | 50 MHz |
| Supply Voltage | 3.13 V to 5.5 V | 3.13 V to 5.5 V | 3.13 V to 5.5 V | 3.13 V to 5.5 V | 3.13 V to 5.5 V | 3.13 V to 5.5 V | 3.13 V to 5.5 V | 3.13 V to 5.5 V | 3.13 V to 5.5 V |
| AEC-Q100 Grade | Qualified | Qualified | Qualified | Qualified | Qualified | Qualified | Qualified | Qualified | Qualified |
| Operating Temperature | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +85 C | -40 C to +125 C |
تفاوت‌های کلیدی
- Same-family Flash-upgrade path with identical pinout (در مقابلS9S12G48F0MLH)
- Better CAN/LIN peripheral integration than S08 predecessors (در مقابلMC9S08DZ60F1CLH)
- Lower unit cost than higher-Flash same-package variants (در مقابلS9S12G128F0MLH)
- Deterministic 16-bit core vs Cortex-M alternatives (در مقابلSTM32H563ZIT6)
یادداشت‌های طراحی
Place a 100 nF X7R ceramic decoupling capacitor within 2 mm of every VDD/VSS pair on the S9S12G64F0MLH to meet the S12G family EMC target. Add a 10 uF bulk ceramic or tantalum at the regulator output to suppress transient loads from CAN/LIN drivers. The on-chip 5 V regulator (VDDR/VSS) supplying internal logic needs its own 100 nF plus 4.7 uF bulk; under-voltage on VDDR will cause unpredictable BDM behavior during debugging.
The 64-LQFP (10x10) package has an estimated theta_JA near 50 C/W on a 4-layer JEDEC test board (estimate; refer to S12G family thermal appendix). At 25 MHz bus clock and 5 V supply, the S9S12G64F0MLH typically draws under 30 mA active and <2 mA stop, so self-heating rarely exceeds 5 C rise above ambient in normal automotive under-dash mounting. Avoid placing the device directly above heat sources like linear regulators; use a thermal relief pattern on the LQFP exposed pad to keep junction temperature below 150 C at +125 C ambient.
Route the CANH and CANL differential pair as a 100 ohm twisted pair with no stubs, keep the bus length under 1 m, and place the TJA104x transceiver within 25 mm of the MCU CAN pins. The EXTAL/XTAL traces should be kept short (<10 mm) and guarded by ground pour; do not route signal traces under the crystal to avoid capacitive loading. The BKGD and RESET pins require careful routing; keep the BDM connector within 50 mm to avoid signal reflections during debug.
Do not exceed the absolute maximum supply voltage of 6 V on any VDD pin or you will permanently damage the S9S12G64F0MLH. Ensure the MODC pin is pulled high through a 4.7 kohm resistor to enter single-chip normal mode; leaving MODC floating at startup will put the MCU in special test mode. The internal oscillator is calibrated to 1 percent but may drift over temperature; for CAN nodes, verify the oscillator meets the 1.58 percent CAN clock tolerance across the full -40 C to +125 C range before relying on it without a crystal.
اطلاعات انطباق
AEC-Q100 qualified for automotive applications per NXP S12G family datasheet. RoHS and REACH compliant. Halogen-free status not explicitly stated in the verified web data.