TJA1057T - 1 Mbit/s High-Speed CAN Transceiver | NXP
MPN: TJA1057T ✗ پایان تولیدTJA1057T نمای کلی
A CAN transceiver is an interface IC within the broader network-interface and automotive electronics hierarchy. It converts the controller's logic-level TXD and RXD signals into a differential bus waveform and converts received bus levels back into a logic signal. This physical-layer function complements the CAN controller, which implements frame handling, arbitration, error detection, and protocol processing above the physical layer.
The verified NXP material identifies the TJA1057 as a member of the Mantis family of high-speed CAN transceivers. The implementation is described as compatible with the CAN physical layer defined in ISO 11898-2:2016 and SAE J2284-1 through SAE J2284-5. The TJA1057T itself is specified for communication rates up to 1 Mbit/s, while the datasheet states that enhanced timing characteristics permit reliable use during the CAN FD fast phase at rates up to 5 Mbit/s for other supported variants.
Automotive network design is the principal use case because the device couples a CAN protocol controller to the vehicle's two-wire bus. It is also relevant to industrial automation, robotics, building automation, and embedded equipment that uses classic CAN rather than a proprietary differential bus. The 8-pin SO package permits compact implementation in conventional through-hole automotive and industrial controller boards.
The central engineering considerations are bus termination, common-mode behavior, transceiver supply requirements, loop delay, and controller timing. A CAN bus normally uses 120-ohm termination at both ends of the network. The transceiver itself does not replace the external bus resistors, and system designers must also account for parasitic cable and stub effects when choosing bit rates, routing, and protection networks.
Because the supplied excerpts do not expose the complete ordering table, electrical limits, pin names, thermal ratings, or verified distributor prices, those details remain explicitly unresolved rather than being inferred. Engineers should use the official NXP datasheet for the final schematic, component values, timing budget, and production release decisions. The TJA1057T is marked NRND on the official NXP product page, so long-term procurement should be confirmed before committing new designs.
This page consolidates the verified manufacturer lifecycle status, CAN standards coverage, data-rate distinction, packaging information, and practical application guidance. It also identifies data gaps and avoids presenting unverified electrical specifications or unsupported drop-in replacements as verified facts.
جایگزین‌های drop-in برای TJA1057T — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای TJA1057T (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Mounting Type, Package, Data Rate, Function, Standby Mode.
TJA1051T/CM118
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
TJA1050T/CM118
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
TJA1044T/1Z
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←TJA1057T مشخصات
| Product Type | High-speed CAN transceiver |
| نرخ داده | 1 Mbit/s for TJA1057T |
| CAN FD Fast-Phase Support | Up to 5 Mbit/s for other TJA1057 variants |
| Bus Interface | Two-wire differential CAN bus |
| Logic Interface | CAN protocol controller |
| CAN Physical-Layer Standard | ISO 11898-2:2016 |
| Automotive Timing Standards | SAE J2284-1 to SAE J2284-5 |
| Product Family | Mantis |
| بسته‌بندی | 8-pin SO package |
| نوع نصب | Through-hole |
| وضعیت چرخه عمر | NRND |
راهنمای پیکربندی پین TJA1057T 8-pin so package
پیکربندی پین برای TJA1057T (پکیج 8-pin so package). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.
داده پین‌آوت تفصیلی موجود نیست برای TJA1057T.
به دیتاشیت برای پیکربندی کامل پین‌ها.
کاربردهای معمول
TJA1057T مناسب است برای 6 کاربردs: Automotive CAN Networks, Industrial Automation Equipment, Robotics and Motion Control, Building Automation Networks, Embedded CAN Gateways, Automotive Diagnostics and Test Equipment.
Automotive CAN Networks
The TJA1057T fits an automotive high-speed CAN node because it provides the differential transmitter and receiver required between a CAN controller and a two-wire vehicle bus. Its verified maximum data rate is 1 Mbit/s, matching conventional high-speed CAN communication rather than a general-purpose differential transceiver. In an engine, body, gateway, or instrument-cluster controller, the device translates TXD and RXD logic signals to and from the physical bus. The NXP datasheet references ISO 11898-2:2016 and SAE J2284-1 through J2284-5, which are directly relevant to physical-layer and automotive timing evaluation. Because the part is marked NRND, engineers should use it primarily for maintenance of qualified designs or after confirming availability, rather than assuming long-term supply security.
پیشنهادی
Industrial Automation Equipment
The TJA1057T is appropriate for industrial automation modules that use a classic CAN physical layer at rates no higher than 1 Mbit/s. It provides the interface between a microcontroller-hosted CAN controller and equipment buses used for sensors, drives, remote I/O, and supervisory control. Its differential CAN implementation is better suited to electrically noisy industrial environments than a single-ended communication path, although the complete EMC and immunity ratings must be checked in the official datasheet. The 8-pin SO package also supports conventional controller-board layouts. Designers should retain external bus protection and proper termination because the transceiver's physical-layer role does not by itself guarantee complete industrial surge, ESD, or ground-fault resilience.
پیشنهادی
Robotics and Motion Control
The TJA1057T can serve as the bus interface on a robot controller, motor controller, or distributed actuator node that uses a two-wire CAN network. Its verified 1 Mbit/s capability is sufficient for command, status, and diagnostic traffic when the network is designed within that rate, while differential signaling provides a practical basis for communication between modules that may share a common ground. The transceiver leaves CAN framing and arbitration to the protocol controller, allowing the selected microcontroller to handle identifiers, arbitration, acknowledgments, and error management. In a robotics system, add suitable bus protection and maintain controlled cable routing because long cables and branch stubs can reduce usable margin even when the nominal data rate is within specification.
پیشنهادی
Building Automation Networks
The TJA1057T is usable in building automation controllers, room-control units, and HVAC interface boards that communicate over a wired CAN-style network. At up to 1 Mbit/s, it supports deterministic command and diagnostic traffic while offloading analog signal levels from the host controller. The eight-pin SO package simplifies repair and legacy-controller compatibility, but lifecycle planning remains important because NXP marks the device NRND. For building systems, designers should verify the official electrical limits, temperature range, and EMC performance for the installation environment. External termination, surge protection, and common-mode considerations are especially relevant when CAN wiring passes between floors or adjacent to mains-derived equipment.
پیشنهادی
Embedded CAN Gateways
The TJA1057T can bridge a CAN controller to a two-wire physical bus in embedded gateways that aggregate sensor data or expose legacy automotive-style interfaces. Its role is deliberately limited to the physical layer: the host processor must implement the CAN protocol controller functions, while the TJA1057T handles differential transmission and reception. This division makes the device useful for diagnostic tools, test fixtures, and communication concentrators. At the verified 1 Mbit/s limit, network loading and protocol efficiency must be considered under worst-case traffic. Engineers should also account for transceiver loop delay within the controller timing budget and verify whether the NRND status is acceptable for the product's planned production lifetime.
پیشنهادی
Automotive Diagnostics and Test Equipment
The TJA1057T is suitable for diagnostic adapters, interface modules, and test equipment intended to communicate with conventional high-speed CAN systems. Its 1 Mbit/s specification allows the adapter to participate in normal bus traffic, while its differential receiver provides a defined interface to a two-wire CAN network. The eight-pin SO package supports straightforward insertion into purpose-built interface boards, although the final product still needs the appropriate connector, isolation decisions, protection, and bus termination. Because this is an NRND device, laboratory and validation equipment may continue to use it for reproducing an existing design, but new production platforms should compare current lifecycle alternatives. The official datasheet remains the controlling reference for pinout and timing.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای TJA1057T — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
TJA1051T/CM118, TJA1050T/CM118, and TJA1044T appear in the verified comparison results as related candidates, but the excerpts do not establish identical pinouts or complete electrical equivalence. Consider one only after a manufacturer-data review confirms package dimensions, TXD and RXD compatibility, supply voltage, logic thresholds, loop delay, standby behavior, and fault tolerance. For a genuinely new design, also compare current active alternatives rather than assuming an NRND component is preferable solely because it matches an older schematic.
مقایسه با جایگزین‌ها
| پارامتر | این محصول | TJA1051T/CM118 | TJA1050T/CM118 | TJA1044T |
|---|---|---|---|---|
| Package | 8-pin SO package | SO-8 | SO-8 | SO-8 |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Product Type | High-speed CAN transceiver | CAN transceiver | CAN transceiver | High-speed CAN transceiver |
تفاوت‌های کلیدی
- Verified 1 Mbit/s high-speed CAN rating (در مقابلTJA1051T/CM118)
- Mantis-family positioning (در مقابلTJA1050T/CM118)
- Direct automotive timing-standard references (در مقابلTJA1044T)
یادداشت‌های طراحی
Do not treat a shared SO-8 outline as proof of drop-in compatibility. Before substituting TJA1051T/CM118, TJA1050T/CM118, or TJA1044T, compare TXD and RXD pin positions, supply pins and voltage range, standby behavior, input thresholds, loop delay, dominant-state behavior, bus-fault handling, and exposed package dimensions against the official TJA1057 datasheet. The supplied comparison excerpts do not provide this complete pin-level evidence, so laboratory validation and board review remain necessary.
Place the transceiver close to the CAN connector or bus-header entry point to minimize the length of unprotected stub. Keep the CANH and CANL routing as a closely coupled differential pair, use the same reference plane where practical, and avoid unrelated test pads or routing in the gap between the pair. The PCB implementation must preserve the datasheet's recommended grounding and decoupling arrangement; consult the official application guidance before finalizing the return path and supply layout.
Design the transceiver supply rail around the official input-voltage range, local bypass capacitance, and controller sequencing requirements, none of which are numerically present in the supplied excerpts. Avoid deriving those values from another TJA10xx device because different family members can use different supply limits or logic thresholds. Verify startup, bus-standoff, and fault states in the complete datasheet, and include reverse-voltage or supply-transient protection only where it does not interfere with the manufacturer's specified operating conditions.
Build the CAN timing budget from the controller's propagation delay, the transceiver's loop-delay symmetry, cable delay, and the network's bit timing. Although the TJA1057T is verified up to 1 Mbit/s, that limit does not make every topology acceptable: long cables, excessive stubs, poor termination, or ground offsets can reduce margin. Confirm the selected sample rate, oscillator tolerance, termination placement, and timing parameters using the official datasheet and an oscilloscope measurement on the final board.
اطلاعات انطباق
The supplied excerpts identify an automotive CAN application and reference SAE J2284 timing standards, but they do not explicitly state this exact part's RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. These fields remain unknown rather than assumed.
