TLV2774ID - Quad 5.1MHz High-Slew-Rate Op Amp | Texas Instruments
MPN: TLV2774ID ✓ فعالTLV2774ID نمای کلی
An operational amplifier is a voltage-feedback amplifier used to amplify, buffer, filter, compare, or drive analog signals. The TLV2774 belongs to the broader hierarchy of operational amplifier, analog amplifier, analog signal-conditioning IC, and semiconductor. Its combination of moderate bandwidth, high slew rate, low quiescent current, and rail-to-rail output makes it useful where fast settling and compact power consumption are more important than very low offset or extremely high precision.
The quad configuration provides four amplifiers in one 14-pin SOIC, reducing board area and simplifying multi-channel designs. Key electrical characteristics include operation from a 2.7 V minimum supply, a 5.5 V maximum supply, 5.1 MHz gain-bandwidth product, 10.5 V/us slew rate, rail-to-rail output swing, and approximately 1 mA supply current per channel. The family also includes a shutdown function, which can reduce system power when the analog section is not active.
The 10.5 V/us slew rate allows the amplifier to produce large voltage transitions quickly, while the 5.1 MHz closed-loop bandwidth supports moderate-frequency signal paths. Rail-to-rail output operation improves usable output range on low-voltage supplies, although designers should still verify output-current and output-voltage limits under the intended load. The CMOS implementation supports low-power portable and industrial equipment where each active channel draws about 1 mA.
Typical uses include sensor-signal conditioning, low-voltage data acquisition, active filtering, audio and communication signal paths, and general-purpose analog front ends. Quad instrumentation in the same package can be used for instrumentation amplifiers, differential stages, buffer chains, and mixed-signal conditioning. Shutdown-capable channels are particularly helpful in battery-powered systems that periodically disable their analog front end.
For PCB implementation, place input and output components close to the relevant amplifier pins and maintain a quiet return path for every channel. Check whether the selected board footprint and pin mapping match the manufacturer pin-description table before final routing. Account for the shutdown-control state during power sequencing because an asserted shutdown level changes the channel operating state rather than simply disconnecting the output.
This page combines manufacturer product information, practical design guidance, package details, comparison information, and sourcing questions for engineers evaluating the TLV2774ID. It is intended to support footprint review, signal-chain planning, power-budget checks, and replacement assessment without overlooking the distinction between electrical equivalence and true pin-to-pin drop-in compatibility.
جایگزینهای drop-in برای TLV2774ID — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
TLV2774CDR
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
TLV2774CDRG4
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
TLV2774ID حداکثر مقادیر مجاز و مشخصات الکتریکی
| Number of Amplifiers | 4 channels |
| Amplifier Type | CMOS operational amplifier |
| Minimum Supply Voltage | 2.7 V |
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 5.1 MHz |
| Slew Rate | 10.5 V/us |
| Supply Current per Channel | 1 mA |
| Output Swing | Rail-to-rail |
| Output Drive | High output drive |
| DC Precision | Excellent DC precision |
| Power Control | Shutdown function |
| بستهبندی | 14-pin SOIC |
| نوع نصب | Surface mount |
| Product Description | Quad, 5.5 V, 5.1 MHz, 10.5 V/us operational amplifier |
راهنمای پیکربندی پین TLV2774ID 14-pin soic
پیکربندی پین برای TLV2774ID (پکیج 14-pin soic). این قطعه آنالوگ دارای پینهای ورودی، خروجی و تغذیه است. برای پیکربندیهای پین offset null، جبرانسازی و فعالسازی به دیتاشیت سازنده مراجعه کنید. ایدهآل برای مدارهای شرطیسازی سیگنال و تقویتکننده.
داده پینآوت تفصیلی موجود نیست برای TLV2774ID.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
TLV2774ID مناسب است برای 6 کاربردs: Low-Voltage Sensor Signal Conditioning, Industrial Data Acquisition, Portable Audio Signal Path, Communication Interface Buffering, Active Filtering and Equalization, Precision Measurement Front End.
Low-Voltage Sensor Signal Conditioning
The TLV2774ID fits four-channel sensor conditioning because each amplifier operates from a 2.7 V minimum supply while drawing approximately 1 mA, making it suitable for compact battery-operated instrumentation. Its rail-to-rail output provides a useful output range on low-voltage rails, and the 10.5 V/us slew rate can reproduce sensor transitions without the sluggish response associated with lower-bandwidth amplifiers. Use the four channels for buffering, gain stages, active filtering, or level conversion. Verify the sensor output range against the amplifier input common-mode limits, and confirm that the selected shutdown state does not disrupt biasing or sensor startup sequencing.
پیشنهادی
Industrial Data Acquisition
The TLV2774ID is appropriate for compact industrial data-acquisition front ends requiring four channels, moderate bandwidth, and low per-channel supply current. Its 5.1 MHz gain-bandwidth product supports signal conditioning beyond low-frequency-only applications, while the 10.5 V/us slew rate improves response to abrupt input changes. The amplifier can support transducer buffers, differential signal stages, anti-alias filters, and ADC driver functions. Industrial systems should still account for ground offsets, input protection, settling time, and the noise contribution of external resistors. The shutdown control should be sequenced carefully when a measurement system must remain valid during wake-up.
پیشنهادی
Portable Audio Signal Path
The TLV2774ID can provide low-voltage analog amplification in portable audio boards where board area and power are constrained. Four rail-to-rail-output amplifiers can handle multiple low-level audio paths, and the 10.5 V/us slew rate offers useful headroom for dynamic signals compared with a slower general-purpose amplifier. The 2.7 V minimum supply supports compact single-cell power systems, while approximately 1 mA per channel helps control consumption. Headphone or line-level driving still requires checking output-current capability, output-voltage margin, stability, and distortion at the selected gain. Avoid treating the listed slew rate as a guarantee of clean full-scale audio output into every load.
پیشنهادی
Communication Interface Buffering
The TLV2774ID is useful for buffering and level-shaping stages around low-voltage communication interfaces. Its 5.1 MHz bandwidth and 10.5 V/us slew rate provide enough speed for moderate-rate control, status, or data-conditioning paths, while rail-to-rail output maximizes swing on 2.7 V to 5.5 V supplies. Four channels allow paired differential signals, transmit and receive conditioning, or protocol-interface support to share one package. The design must observe input common-mode limits, output loading, and the data sheet’s recommended feedback topology. For high-speed links, verify the actual channel bandwidth and settling requirements rather than using the gain-bandwidth product alone.
پیشنهادی
Active Filtering and Equalization
The TLV2774ID supports active filter and equalization designs that need more bandwidth than precision-only op amps while retaining reasonably low power consumption. Its 5.1 MHz gain-bandwidth product permits useful closed-loop response in the megahertz range, and the 10.5 V/us slew rate reduces distortion during larger signal transitions. The four amplifiers can implement low-pass, high-pass, band-pass, notch, or active-feedback stages around sensors and communications circuits. Component tolerances, parasitic capacitance, and loop gain determine actual response. Validate stability and gain margin across temperature and supply tolerances, and avoid overdriving the input or output range of the 2.7 V to 5.5 V operating class.
پیشنهادی
Precision Measurement Front End
The TLV2774ID can form part of a compact measurement front end because it combines four channels with 0.1 mV/us-class high slew-rate performance, rail-to-rail output, and low supply current. It can implement amplifier instrumentation stages, difference amplifiers, level-shifting buffers, and active filters around bridge, temperature, or pressure sensors. The device’s excellent DC precision supports this role, but exact offset, bias-current, drift, and common-mode values must be checked against the measurement error budget. For high-impedance sources, input bias current and sensor loading can dominate the result. Keep feedback resistors within recommended ranges, provide clean grounding, and calibrate offsets when required by the instrument specification.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای TLV2774ID — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | TLV2774CDR | TLV2774CDRG4 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin SOIC | 14-pin SOIC - same | 14-pin SOIC - same |
| Number of Amplifiers | 4 channels | 4 channels | 4 channels |
| Minimum Supply Voltage | 2.7 V | 2.7 V | 2.7 V |
| Maximum Supply Voltage | 5.5 V | 5.5 V | 5.5 V |
| Gain-Bandwidth Product | 5.1 MHz | 5.1 MHz | 5.1 MHz |
| Slew Rate | 10.5 V/us | 10.5 V/us | 10.5 V/us |
| Supply Current per Channel | 1 mA | 1 mA | 1 mA |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Power Control | Shutdown function | Shutdown function | Shutdown function |
تفاوتهای کلیدی
- Combines four channels with high slew rate in one SOIC (در مقابلTLV2774CDR)
- Low-voltage, rail-to-rail output operation (در مقابلTLV2774CDRG4)
- Power-conscious four-channel integration (در مقابلTLV2774CDR)
یادداشتهای طراحی
Budget the four channels separately: approximately 1 mA per channel gives a nominal amplifier-family supply current of about 4 mA before shutdown savings and external-load effects. Check this total against the regulator’s capacity, dropout margin, and quiescent current. If shutdown is used, include the control-pin state in the system power budget and ensure that waking the amplifier cannot disturb a sensitive analog node.
Route each channel as a compact analog path, placing feedback resistors, input components, and decoupling capacitors close to their associated pins. Keep digital switching nodes and high-current return paths away from input and output traces. For a quad device, treat the four channels as separate layouts rather than assuming one excellent placement can compensate for shared supply impedance or ground coupling.
Do not assume that any 14-pin quad op amp is automatically interchangeable. Confirm the complete pin-description table, shutdown-pin polarity, input common-mode range, output-swing behavior, and package variant against the Texas Instruments datasheet. The available same-family alternatives match the principal voltage, bandwidth, slew-rate, and current ratings, but production qualification and lifecycle requirements still need to match the finished equipment.
Use stable feedback networks and verify the intended closed-loop bandwidth rather than treating the 5.1 MHz gain-bandwidth product as the usable signal bandwidth. The 10.5 V/us slew rate helps reproduce fast transitions, but output loading, gain, supply voltage, and output-voltage headroom determine large-signal behavior. Simulate or measure settling and oscillation in the final board, especially when driving long traces or capacitive inputs.
اطلاعات انطباق
The available product listings and comparison excerpts do not explicitly establish the requested compliance statuses. Qualification and green-composition attributes should be confirmed from the manufacturer ordering information for the exact TLV2774ID suffix.