Circuits intégrés

Sous-catégories

📁 ADC/DAC 2 700+ produits 📁 CI amplificateurs 1 100+ produits 📁 Codecs audio 18 produits 📁 CI audio 2 produits 📁 Horloge et synchronisation 480+ produits 📁 Comparator ICs 0 produits 📁 DSP 1 000+ produits 📁 CI d'acquisition de données 2 produits 📁 Potentiomètres numériques 4 produits 📁 Pilotes et contrôleurs d'affichage 1 produits 📁 FPGA & CPLD 6 800+ produits 📁 Circuits intégrés d'interface 2 300+ produits 📁 Pilotes de LED 1 produits 📁 CI logiques 360+ produits 📁 CI mémoire 870+ produits 📁 Microcontrôleurs 19 000+ produits 📁 Microprocesseurs 4 produits 📁 Pilotes de moteur 1 produits 📁 Autres 1 produits 📁 Sensor and Detector Interfaces 1 produits 📁 Circuits intégrés spécialisés 15 produits 📁 CI vidéo 13 produits

Produits (35 000+)

TPS65193RGER - Dual High-Voltage TFT-LCD Scan Driver | TI
TPS65193RGER

TPS65193RGER - Dual High-Voltage TFT-LCD Scan Driver | TI

The Texas Instruments TPS65193RGER is a dual high-voltage scan driver for amorphous-silicon-gate TFT LCD panels, providing high-voltage gate-line outputs from -28 V to 35 V in a 24-VQFN 4 mm x 4 mm package. Each scan-driver section accepts a logic-level CPV input and produces complementary CKV and CKVB outputs, while a logic-level STV input generates the high-voltage STVP output. A high-voltage scan driver is a specialized interface IC that transfers low-voltage timing commands from the host controller to the elevated voltages required by TFT gate lines. Its position in the display hierarchy is controller interface, then row-driver interface, then gate-line scan driver. This device does not process image data; instead, it supplies the high-voltage, charge-sharing waveforms that select and bias TFT rows. Key features include a 35 V high output-voltage level, an output swing down to -28 V, scan-driver output charge sharing, and four logic-level inputs. The 24-VQFN package measures 4 mm on each side, supporting compact display-module designs where connector count and board area are constrained. The RGER orderable designation identifies the 4 mm x 4 mm VQFN package configuration. Each high-voltage scan driver receives CPVx and generates two outputs, CKVx and CKVBx. A separate STV logic input produces the STVP output. Charge sharing reduces peak drive demand by transferring charge between the complementary outputs rather than driving each output as an isolated hard switch, helping lower switching loss in the gate-line drive network. Typical applications are amorphous-silicon TFT LCD modules, including small-panel monitors, portable instruments, industrial HMIs, test equipment, and control-system displays. The device is most appropriate where the panel requires negative off-level and positive high-level gate drive but does not require a separate source-driver solution from the same device. Designers must account for the -28 V to 35 V output range, provide suitable bypassing on the high-voltage supply rails, and validate output timing against the target TFT panel. Panel bias requirements, leakage into neighboring rows, and clock-edge placement determine whether the charge-sharing outputs provide adequate settling time. This page consolidates the verified manufacturer and distributor information, separates documented specifications from unavailable data, and provides application guidance and comparison considerations that are not presented as a substitute for the complete Texas Instruments datasheet.

Devis Contact
TPS65195YFFR 8-Channel Display Level Shifter | TI
TPS65195YFFR

TPS65195YFFR 8-Channel Display Level Shifter | TI

The Texas Instruments TPS65195YFFR is an 8-channel display power and level-shifting integrated circuit packaged in a 30-pin DSBGA. Distributor records classify the device as a video processing IC and an 8-channel level shifter, placing it within the display-interface and video-signal-conversion segment of integrated-circuit applications. Its defining verified characteristics are the eight-channel architecture, display-oriented level-shifting function, and compact 30-DSBGA package. Detailed electrical ratings, supported logic standards, voltage limits, timing values, and thermal limits were not included in the supplied source material and therefore require confirmation from the manufacturer datasheet before schematic or layout release. A display level shifter is an interface IC that translates signals between voltage domains that use different electrical thresholds. This allows a host processor, graphics engine, or display controller to communicate more reliably with display-panel circuitry when input and output levels are not directly compatible. In the broader semiconductor hierarchy, the TPS65195YFFR belongs to interface ICs and, more specifically, to video interface ICs. Its eight channels allow multiple display-related signals to be handled within one package, reducing the component count compared with discrete translators. The verified distributor listing identifies the part as an 8-channel level shifter in a 30-pin DSBGA. This combination can be valuable in compact display modules where board area is constrained and several voltage-domain crossings are required. The BGA form factor also supports dense routing, although it demands assembly processes capable of handling fine-pitch balls. Package dimensions, ball pitch, exposed-pad details, soldering profiles, and reflow requirements must be taken from the official package drawing rather than inferred from the distributor description. Typical design use is a display controller interface, an LCD panel bias or signal interface, and a compact embedded display module. These uses follow from the verified display power and level-shifting classification; the supplied data does not enumerate supported panel interfaces or timing standards. Engineers should therefore treat the TPS65195YFFR as a display-interface candidate, not as a complete or independently characterized video processor, until channel direction, signal type, voltage ranges, and timing constraints are verified. A key implementation consideration is validating every connected display signal against the manufacturer's absolute-maximum and recommended operating limits. Because no pinout was supplied in the verified results, no pin assignments are asserted here. The official datasheet and land-pattern information must be used to confirm signal direction, supply pins, ground pins, and unused-ball handling before PCB routing begins. This page consolidates the verified distributor identity, package, and sourcing information with a structured engineering workflow for datasheet validation, alternative qualification, and display-interface design. It distinguishes confirmed facts from unavailable parameters rather than filling gaps with guessed electrical values.

Devis Contact
TPS65197RUYR - 8-Channel LCD Level Shifter | Texas Instruments
TPS65197RUYR

TPS65197RUYR - 8-Channel LCD Level Shifter | Texas Instruments

The Texas Instruments TPS65197RUYR is an 8-channel level-shifter IC for LCD display applications, packaged in a 28-pin WQFN (RUY) package measuring 4 mm by 4 mm. It supports 2-channel and 3-channel charge-sharing methods, normal level-shifting operation, and panel discharge to VGH during shutdown. The device is designed to translate timing-controller logic-level signals into the higher gate-level signals required by gate-in-panel (GIP) LCD panels. TPS65197RUYR belongs to the interface IC and display-driver ecosystem. A level shifter is an interface IC that translates voltage domains while preserving signal timing and logic function. In an LCD system, the timing controller operates at lower logic voltages, while GIP row and column driver circuits may require elevated panel voltages. The TPS65197 provides eight channels for this signal conversion and supports panel-specific charge-sharing sequences that help control panel charging and discharge behavior. The principal feature set includes eight level-shifting channels, support for no-charge-sharing, 2-channel charge-sharing, and 3-channel charge-sharing operation, and a dedicated panel-discharge function. The manufacturer product page identifies the device as an 8-channel level-shifter supporting 2-channel and 3-channel charge-sharing and panel discharge in the WQFN (RUY) package with 28 pins. Because GIP panels can accumulate charge and generate transient loads during startup, the charge-sharing architecture is important. The supported operating modes let a system select a charging strategy according to panel timing requirements rather than using a simple fixed level translation approach. The shutdown discharge path provides a defined mechanism for returning panel nodes toward VGH during power-down. Typical uses include notebook computer LCD panels, desktop monitors, television panels, and other GIP-based display systems. The device is most appropriate when the source logic levels, panel gate-drive levels, supported charge-sharing sequence, and shutdown behavior must all be evaluated together. A replacement should not be selected solely by channel count; the timing of each output, panel discharge behavior, voltage ratings, and board footprint must be confirmed against the original design. This page combines the verified manufacturer description, distributor package information, drop-in alternatives, and engineering-oriented design guidance. The 28-pin WQFN footprint, exposed thermal pad, high-speed panel signals, and power-sequencing requirements should be reviewed against the complete manufacturer datasheet before layout or replacement qualification.

Devis Contact
TPS65198RUYR - 13-Channel LCD Level Shifter | Texas Instruments
TPS65198RUYR

TPS65198RUYR - 13-Channel LCD Level Shifter | Texas Instruments

The Texas Instruments TPS65198RUYR is a 13-channel level shifter with an integrated operational amplifier for LCD televisions and monitors, supplied in a 28-pin WQFN (RUY) package measuring 4 x 4 mm. It supports an operating temperature range of -40 C to +85 C and is designed for display-interface applications where multiple voltage domains and signal buffering are required. A level shifter is an interface IC that translates logic signals between voltage domains whose high and low thresholds differ. In an LCD television or monitor, source electronics, timing controllers, panel interfaces, and backlight systems may operate from different supply rails. A multi-channel level shifter allows those signals to cross between incompatible voltage domains, while the integrated operational amplifier provides buffering for a signal that requires drive or amplification. The TPS65198RUYR's 13-channel architecture consolidates multiple translated logic connections in one package. This can reduce the number of discrete level-shifter components and simplify printed-circuit-board layout compared with a collection of individual translators. Its 4 x 4 mm WQFN format also supports compact display-control designs where connector density and panel-interface routing leave limited board area. The verified operating temperature range is -40 C to +85 C, covering industrial temperature conditions commonly encountered in display electronics. The available LCSC listing identifies an 8 V to 20 V supply-related value, but the provided source excerpt does not clearly identify that parameter or its test conditions; consequently, voltage limits, channel direction, translation thresholds, and the integrated amplifier's electrical ratings require confirmation in the manufacturer datasheet before design release. Typical uses include LCD monitor panel-interface circuits, television timing and control boards, display power-sequence logic, and other multi-rail display systems where a compact level-translation stage is needed. Because this device combines translation and amplification, it can simplify signal-interface design when the source impedance and loading requirements of the translated channels differ. Engineers should confirm every channel's direction, voltage domain, enable behavior, and the exposed-pad connection directly against the TI datasheet and the PCB footprint. The 28-pin WQFN package is also thermally and assembly sensitive; proper land-pattern compliance, paste control, and exposed-pad soldering are required for reliable production yield. This page consolidates the verified manufacturer identification, distributor package data, temperature rating, and supply-range excerpt for TPS65198RUYR, while clearly separating missing electrical data from confirmed values. It also documents the absence of a manufacturer-verified drop-in substitute rather than presenting an unverified package conversion as a drop-in replacement.

Devis Contact
TPS65198RUYT - 13-Channel Level Shifter | Texas Instruments
TPS65198RUYT

TPS65198RUYT - 13-Channel Level Shifter | Texas Instruments

The Texas Instruments TPS65198RUYT is a 13-channel level shifter with an integrated operational amplifier for GIP-based LCD television and monitor applications, packaged in a 28-pin WQFN (RUY) 4 x 4 mm package. It accepts five timing-controller input signals, uses an internal state machine to generate twelve output signals, and combines level shifting with op-amp signal conditioning. Its specified operating-temperature range is -40°C to +85°C. A level shifter is an interface device that translates logic-voltage levels so circuits using different voltage domains can communicate reliably. In this application, the TPS65198 belongs to the display-driver interface hierarchy: logic level translation, display timing-interface conversion, voltage-domain interfacing, and display-driver ICs. Its integrated op amp provides an additional analog signal-conditioning function alongside the digital level-shift outputs. The principal feature is the combination of a 13-channel level-shifting architecture, five external inputs, twelve internally generated outputs, and op-amp integration. This consolidation can simplify the circuitry associated with GIP panel timing control. The built-in state machine sequences the generated outputs according to the panel-interface requirements, while the integrated amplifier can support signal conditioning where the timing interface requires amplification or level adjustment. TPS65198RUYT is intended for LCD TVs and monitors using GIP technology, where multiple panel signals must be shifted between source-driver, gate-driver, and timing-controller voltage domains. The 4 x 4 mm WQFN package supports compact display-controller boards, but its exposed thermal-pad construction requires careful PCB layout for electrical return paths and heat spreading. Designers should also account for the high-speed edge behavior of the interface when routing signals and selecting input and output impedance. Typical uses include large-panel LCD television timing control, LCD monitor panel interfaces, and other GIP display systems that require coordinated multi-channel level translation. Because the verified source set identifies a 28-pin WQFN package and a -40°C to +85°C range, the device is appropriate for industrial and consumer display environments requiring operation across that temperature span. The principal design consideration is to follow the manufacturer datasheet exactly for exposed-pad connection, decoupling, signal routing, and output-state sequencing. Place input and output return paths close to the device, provide the specified supply and bypass capacitance, and avoid introducing stubs on timing signals. Verify every panel connector voltage domain and the state-machine timing before releasing a display board. This page consolidates the verified manufacturer and distributor information, distinguishes a true drop-in replacement from a packaging-only ordering variant, and highlights application-specific design considerations that are not apparent from a basic distributor listing.

Devis Contact
TPS66021YBGR - 20V Sink, 5V Source USB-C Switch | TI
TPS66021YBGR

TPS66021YBGR - 20V Sink, 5V Source USB-C Switch | TI

The Texas Instruments TPS66021YBGR is a one-channel integrated USB-C Power Delivery source-and-sink power multiplexer with a 20V sink path, a 5V source path, and a 5V dead-battery VBUS LDO, housed in a 28-ball DSBGA package measuring 1.61 mm by 2.81 mm. It combines two directional power paths in a compact device intended to manage charging, powering, and protection around a USB-C connection. A USB-C power-path multiplexer is a specialized power-management integrated circuit that controls current between a connector and internal supply rails. It belongs to the hierarchy power multiplexer, power-path controller, power-management IC, and semiconductor. By combining source and sink switching, it can route external VBUS power into a system, provide regulated 5V power from an internal source, and isolate paths during faults or operating-mode changes. The verified manufacturer data identifies a 4V-to-22V sink power path and a 5V source path. The source path enters constant-current operation when its load exceeds the selected current-limit threshold. Each path includes overtemperature and reverse-current protection, while the family supports a fault indication for overcurrent and overtemperature events. The integrated high-voltage VBUS LDO provides 5V for this device and other system components under dead-battery conditions. The TPS66021 integrates a 20V USB-C sink capability and 5V source capability rather than acting only as a passive analog switch. Its VBUS-side architecture allows the system to distinguish and control external power conditions, while the source path supplies a defined output level. The fault function gives the host circuitry a signal when protection circuitry has detected an abnormal event, enabling controlled shutdown or fault recovery. Typical uses include USB-C laptop and tablet power adapters, portable equipment, battery-powered industrial products, and compact systems that must accept external USB-C power while retaining a safe internal 5V supply. The integrated source, sink, and dead-battery functions can reduce board area compared with a discrete switch network. Designers must still validate connector orientation, CC behavior, capacitor selection, current limits, thermal performance, and system power sequencing against the full manufacturer documentation. For PCB layout, follow the manufacturer package land pattern and place high-current input, output, and ground connections with short, wide paths. Place required input and output capacitors close to their associated balls and keep sensitive control and fault traces away from high-di/dt power loops. Verify the selected current threshold, startup behavior, and fault response in the final USB-C system. This page consolidates verified manufacturer descriptions, distributor availability, package information, replacement evidence, and application guidance. It also distinguishes confirmed facts from parameters that require the complete datasheet, preventing unsupported electrical or compliance assumptions during design review.

Devis Contact
TPS8802DCPR - Smoke Alarm AFE with CO Support | TI
TPS8802DCPR

TPS8802DCPR - Smoke Alarm AFE with CO Support | TI

The Texas Instruments TPS8802DCPR is a smoke-alarm analog front end (AFE) for residential smoke detectors, integrating the regulators, amplifiers, and drivers required for a dual-wave photoelectric smoke alarm and carbon monoxide detection system. The verified distributor listing identifies a 38-pin HTSSOP package and analog input with I2C output. TI describes the device as a high-performance, multi-channel, digital-input solution whose flexible architecture suits smoke-alarm systems where precision and power consumption are critical. What is a smoke-alarm analog front end? An AFE is a semiconductor that connects physical sensing elements to an embedded system. In a photoelectric alarm, light scattering and light-absorption signals require controlled excitation, amplification, filtering, and diagnosis. The TPS8802DCPR integrates those signal-chain functions together with supporting regulators and drivers, reducing the number of discrete components and helping designers create a compact, low-power detector platform. The verified TI product information highlights a wide input-voltage range, low standby-power consumption, and power-saving features designed to support 10-year battery-powered smoke-alarm systems. Its dual-wave photoelectric architecture and CO-detection capability allow one integrated platform to combine optical smoke sensing with electrochemical CO-sensor signal conditioning. The I2C interface provides a digital control and diagnostic path, while the analog input supports direct connection to sensing circuitry. The TPS8802DCPR is intended for residential smoke alarms, combination smoke-and-CO alarms, and other safety products requiring highly integrated sensing support. Its integrated regulators and amplifiers can simplify power-tree design compared with a discrete implementation, while digital configuration can support manufacturing tests and field diagnostics. Exact electrical limits, gain settings, timing values, and pin functions were not included in the supplied verified records and therefore require confirmation from the manufacturer datasheet before design release. For battery operation, standby current is especially important because the target application is a long-lived safety device. Designers should calculate average and peak current across the sensing duty cycle, confirm regulator startup behavior, and verify that low-power modes preserve alarm thresholds and diagnostic performance. The I2C pull-up arrangement, grounding, and decoupling should follow the manufacturer layout guidance to prevent communication errors or unintended current consumption. This product page consolidates the verified distributor classification, manufacturer application description, package information, source links, and design cautions. It does not invent electrical parameters or claim unverified drop-in equivalents. Confirm the complete pinout, absolute maximum ratings, recommended operating conditions, and lifecycle status in the current Texas Instruments documentation before schematic capture or PCB release.

Devis Contact
TPS8804DCPR - Analog Front End for Commercial Smoke Detector | Texas Instruments
TPS8804DCPR

TPS8804DCPR - Analog Front End for Commercial Smoke Detector | Texas Instruments

The Texas Instruments TPS8804DCPR is an integrated analog front end (AFE) and system power management IC for commercial smoke detectors. Housed in a 38-pin HTSSOP (DCP) package, it integrates multiple functions including photoelectric chamber driver circuitry, a piezo buzzer driver, an I2C communication interface, and a low-dropout (LDO) regulator chain to support battery-powered smoke alarm designs. A smoke detector AFE is a specialized analog front end that combines the bias and signal-conditioning paths used by optical or ionization smoke sensors with the housekeeping functions needed to run a battery-powered alarm. The TPS8804DCPR falls within the broader family of sensor and detector interface ICs that sit between the physical sensor element (photodiode or ionization chamber) and the system microcontroller or horns driver. Its role is to power, bias, read, and test the sensor while managing battery life, supervisory housekeeping, and interconnect functions across multi-unit networked installations. Key features include analog signal paths for both photoelectric and ionization smoke sensor types, an integrated boost converter for high-current piezo buzzer drive, an integrated LDO chain for system rails, an I2C interface for configuration and status readback, an interconnect driver for interlinking multiple smoke alarm units in a building, and on-chip timers for sensor self-test. The IC is intended for use with an external MCU that runs the smoke detection firmware. Operating voltage is designed to support common 9V battery and regulated mains-powered topologies. The TPS8804DCPR is optimized for ultra-low standby current so the detector can sit on a battery for years without replacement, while still providing rapid sensor biasing and high-current piezo drive during an alarm event. Its integrated boost converter eliminates the need for a discrete driver MOSFET and inductor for the buzzer, reducing BOM count. The HTSSOP-38 package provides adequate thermal dissipation for the piezo boost stage at typical alarm sound pressure levels. Typical applications include residential and commercial smoke alarms, CO-and-smoke combination detectors, heat detectors with piezo alarms, and industrial safety notification appliances. The interconnect feature lets installers link multiple units so that all alarms sound when any one unit triggers, a key requirement for multi-room buildings. When designing with this part, follow the reference layout in the TPS8804 datasheet for the boost inductor and feedback loop. Use low-leakage ceramic capacitors on the photo-sensor input to preserve low standby current and accurate chamber biasing. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not found in the manufacturer datasheet alone.

Devis Contact
TRS3221EIDBR - 3-5.5V RS-232 Transceiver, ±15kV ESD | Texas Instruments
TRS3221EIDBR

TRS3221EIDBR - 3-5.5V RS-232 Transceiver, ±15kV ESD | Texas Instruments

The Texas Instruments TRS3221EIDBR is a 3-V to 5.5-V single-channel RS-232 line driver/receiver with ±15-kV IEC-ESD protection, packaged in a 16-pin SSOP (DB). It operates from a single supply rail and integrates a charge-pump that generates the ±RS-232 voltage swing from the input supply, so no external ±12 V rails are required. The device supports data rates up to 250 kbps and is rated for ±15-kV HBM, ±8-kV IEC 61000-4-2 contact, and ±15-kV IEC 61000-4-2 air-gap ESD strikes on the RS-232 bus pins. An RS-232 transceiver is a type of line driver/receiver IC that converts logic-level (typically 0/3.3 V or 0/5 V CMOS/CMOS) UART signals into the ±5 V to ±15 V voltage swings required by the TIA/EIA-232-F and ITU v.28 standards. It belongs to the broader interface-IC category, sitting between the UART block of a microcontroller/SoC and a DB-9 (or equivalent) connector on the serial port. Single-channel variants like the TRS3221E serve compact, point-to-point designs where two driver/receiver channels are not needed, helping shrink BOM cost and PCB area versus 2-channel parts. Key features include 1 driver and 1 receiver per channel, a dedicated enable input for power management, an auto-powerdown mode that drops quiescent current to 1 µA typical when the cable is disconnected, and an always-active supplementary receiver that monitors the ring-indicator path even in shutdown. The device meets or exceeds the TIA/EIA-232-F and ITU v.28 electrical specifications, and is offered in industrial temperature grades of -40 °C to +85 °C. A high-speed pin-compatible upgrade, the TRSF3221E, is available where 1 Mbit/s operation is required. The TRS3221E uses an on-chip switched-capacitor voltage converter with four external 0.1 µF charge-pump capacitors. The architecture tolerates supply rails as low as 3.0 V while still generating compliant ±5 V (minimum) RS-232 output swings, which is the headline advantage over legacy 5-V-only RS-232 transceivers. Drivers are slew-rate limited to keep EMI low, and the receivers include hysteresis to reject noise on long cables. Typical applications include industrial single-port serial ports, point-of-sale terminals, handheld data collectors, factory automation equipment, medical instruments with DB-9 serial interfaces, and any embedded system that needs a robust RS-232 link from a 3.3 V or 5 V UART. Designers often pair this part with a TVS array for additional surge protection when the cable is exposed to outdoor or industrial transients. When designing with the TRS3221EIDBR, place the four charge-pump capacitors (typically 0.1 µF X7R) as close as possible to the C0+, C0-, C1+, C1- pins to minimize supply ripple. Decouple VCC with a 0.1 µF + 1 µF combination near the pin, and respect the absolute-maximum ratings on the RS-232 outputs (typically ±13.2 V) by avoiding back-drive when the IC is unpowered. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
TRS3221EIRGTR - 3-5.5V RS-232 Transceiver, 250kbps, ±15kV ESD | Texas Instruments
TRS3221EIRGTR

TRS3221EIRGTR - 3-5.5V RS-232 Transceiver, 250kbps, ±15kV ESD | Texas Instruments

The Texas Instruments TRS3221EIRGTR is a 3- to 5.5-V single-channel RS-232 line driver/receiver delivering 250 kbps data rate with ±15 kV IEC-ESD protection in a 16-pin VQFN (RGT) package measuring 3x3 mm with an exposed thermal pad. The device integrates one driver and one receiver, supports VCC operation from 3.0 V to 5.5 V (compatible with TTL/CMOS logic levels), and meets or exceeds the requirements of TIA/EIA-232-F and ITU v.28 standards. An RS-232 transceiver is a charge-pump-based interface IC that translates between TTL/CMOS logic levels (0-3.3 V or 0-5 V) and the ±5 V to ±15 V swing required by the legacy TIA/EIA-232-F serial communication standard. RS-232 transceivers belong to the broader interface IC family, which sits hierarchically between discrete level-shifters and protocol controllers (UARTs) in wired communication systems. RS-232 remains widely deployed in industrial equipment, point-of-sale terminals, medical instruments, and embedded debug ports where simplicity, point-to-point connectivity, and proven robustness outweigh the bandwidth advantages of USB or Ethernet. Key features include ±15 kV Human-Body Model (HBM) ESD protection on RS-232 pins, ±8 kV IEC 61000-4-2 contact discharge, ±15 kV IEC 61000-4-2 air-gap discharge, and an automatic powerdown feature that disables drivers when no valid RS-232 cable is detected. The on-chip dual charge pump requires only four external 0.1 µF capacitors, enabling true 5 V operation from a single 3.3 V supply without a separate ±12 V rail. The 250 kbps data rate is adequate for all standard RS-232 baud rates up to and beyond 115200 with margin to spare. The architecture combines a regulated switched-capacitor voltage doubler/inverter with a proprietary low-dropout RS-232 driver stage and a precision hysteresis receiver. ESD protection is implemented at the cable-side pins using TI's integrated silicon-controlled-rectifier (SCR) clamps. The 16-pin VQFN package's exposed pad provides a low thermal resistance path, which is useful when the part operates near the upper end of its 1 mA quiescent current budget in warm enclosures. Typical applications include industrial PLC programming ports, point-of-sale (POS) terminals, medical device serial consoles, battery-powered handhelds, and embedded debug UARTs that need robust ESD performance in the field. The TRS3221EIRGTR's small 3x3 mm footprint suits space-constrained designs such as USB-to-serial dongles, IoT gateways, and barcode scanners. When designing with this part, place the four charge-pump capacitors as close as possible to the C1+ / C1- / C2+ / C2- pins and keep the RS-232 trace lengths short to maximize ESD margin. Note that the TRSF3221E is the higher-speed (1 Mbit/s) pin-compatible alternative if 250 kbps is insufficient. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
TRSF3222CPW - 3V-5.5V RS-232 Transceiver, 2/2 Drivers | TI TSSOP-20
TRSF3222CPW

TRSF3222CPW - 3V-5.5V RS-232 Transceiver, 2/2 Drivers | TI TSSOP-20

The Texas Instruments TRSF3222CPW is a 2-driver/2-receiver RS-232 line transceiver that operates from a single 3.0V to 5.5V supply in a 20-pin TSSOP package. It supports data rates up to 1 Mbit/s and accepts 5-V logic inputs when powered from a 3.3V rail, making it ideal for mixed-voltage system designs. A line transceiver is an interface device that bridges a logic-level UART (universal asynchronous receiver/transmitter) on a host microcontroller with the RS-232 standard, which swings between +12V and -12V on the bus side. It sits within the Interface IC hierarchy (RS-232 transceiver -> line transceiver -> interface IC -> integrated circuit) and converts TTL/CMOS logic levels to TIA/EIA-232-F compliant voltage levels while protecting the host from ESD events on the cable side. The TRSF3222CPW integrates a dual charge-pump that generates the required +5.5V and -5.5V rails from a single 3.3V supply using four small 0.1 uF external capacitors. Standby current is typically 1 uA, supporting low-power portable designs. The receivers remain active in shutdown, allowing wake-up characters to be detected without waking the host. ESD protection exceeds +/-15 kV HBM on the bus pins. Typical applications include industrial point-of-sale terminals, factory automation equipment, portable diagnostic instruments, and battery-powered barcode scanners where 3.3V logic must communicate with legacy RS-232 peripherals. The wide 3.0V-5.5V supply range also makes the part suitable for USB-to-serial bridges and embedded computing modules. When designing with this device, place the four charge-pump capacitors as close to the IC as possible to minimize loop inductance. The TSSOP-20 footprint requires standard surface-mount assembly with a maximum reflow temperature per JEDEC J-STD-020. Decouple VCC with a 0.1 uF ceramic plus a bulk tantalum if the supply impedance is high.

Devis Contact
TS321ID - Single 30 V 800 kHz Op Amp | Texas Instruments
TS321ID

TS321ID - Single 30 V 800 kHz Op Amp | Texas Instruments

Texas Instruments TS321ID is a single bipolar operational amplifier rated for 30 V operation, an 800 kHz gain-bandwidth product, and an 8-pin SOIC package. It is intended for cost-sensitive applications where space savings matter, making it a compact general-purpose amplifier for industrial, instrumentation, and signal-conditioning systems. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The TS321 belongs to the broader hierarchy of operational amplifier, analog amplifier, signal-conditioning IC, and semiconductor. Its basic amplifier functions include voltage amplification, buffering, filtering, summing, and feedback-based control, provided the external feedback network and operating limits are respected. The verified product information identifies a single amplifier circuit, a 30 V maximum operating framework, 800 kHz bandwidth, general-purpose classification, and an 8-pin SOIC package. The bipolar architecture and low-power positioning suit cost-sensitive designs, while the SOIC footprint supports conventional surface-mount assembly. Exact offset, bias-current, noise, slew-rate, common-mode, and output-swing values require confirmation in the manufacturer datasheet before final circuit sign-off. TS321ID is useful as a general-purpose amplifier in low- and moderate-bandwidth analog paths. Its verified 800 kHz bandwidth makes it relevant to signal conditioning where the required closed-loop bandwidth is well below that level. The single-amplifier configuration can simplify designs that need one amplifier rather than a dual package, particularly in sensor interfaces, control loops, audio preamplification, and industrial measurement circuits. The principal design consideration is preserving signal headroom and stability. An 8-pin SOIC package requires adequate PCB spacing, controlled grounding, and decoupling close to the power pins. Feedback resistors, compensation components, and input or output loading determine the actual usable bandwidth and must be evaluated against the application. Because verified operating details beyond the supplied values are incomplete, engineers should consult the TS321 manufacturer datasheet before choosing component values. This page combines verified manufacturer and distributor information, structured technical context, sourcing guidance, and engineering notes. It also clearly identifies unavailable electrical parameters rather than presenting guessed values, helping engineers move from part selection to a validated TS321ID design with fewer sourcing and specification ambiguities.

Devis Contact
TS3A27518ERTWR - 6-Ch 2:1 Analog Mux, 240MHz | Texas Instruments
TS3A27518ERTWR

TS3A27518ERTWR - 6-Ch 2:1 Analog Mux, 240MHz | Texas Instruments

The Texas Instruments TS3A27518ERTWR is a bidirectional 6-channel 1:2 (SPDT) analog multiplexer/demultiplexer with 6.2 ohm on-resistance, 240 MHz bandwidth, and integrated IEC 61000-4-2 ESD protection, housed in a 24-pin WQFN (4x4 mm) package operating from a 1.65 V to 3.6 V single supply. An analog multiplexer is a signal-routing semiconductor that selects one of several input channels and connects it to a common output, functioning as a digitally controlled switch for both analog and digital signals. Within the signal-chain hierarchy, it sits between passive switches and full crosspoint matrices, and belongs to the broader family of interface and analog switch ICs used in power management and signal conditioning subsystems. Key features include low 6.2 ohm typical on-resistance for minimal signal attenuation, 21.5 pF typical switch capacitance, up to 240 MHz bandwidth for high-speed rail-to-rail signal handling, and -62 dB crosstalk and OFF isolation. The device also provides isolation in power-down mode (VCC = 0 V), and 1.8 V logic-threshold-compatible control inputs that allow direct interfacing with low-voltage microcontrollers. Architecturally, the TS3A27518E uses two control pins, each simultaneously controlling three 1:2 multiplexer sections, plus an enable pin that places all outputs in high-impedance mode. Integrated ESD cells rated to IEC 61000-4-2 on the signal pins eliminate the need for external TVS diodes in USB and port-protection designs, and the device is qualified for automotive applications. Typical applications include USB 2.0 high-speed signal switching, audio jack and headset detection, battery-powered portable equipment, and general-purpose analog signal routing in industrial systems. A key design consideration is on-resistance flatness across the signal range: at lower VCC the Ron rises, so budget for insertion loss at 1.65 V operation, and keep stub lengths short to preserve the 240 MHz bandwidth. This page adds value beyond the datasheet by synthesizing distributor pricing tiers, drop-in alternatives, cross-reference data, and practical design notes in one reference.

Devis Contact
TS3A44159RGTR - 0.45Ω Quad SPDT Analog Switch | TI
TS3A44159RGTR

TS3A44159RGTR - 0.45Ω Quad SPDT Analog Switch | TI

The Texas Instruments TS3A44159RGTR is a 0.45-Ω quad-channel single-pole double-throw (SPDT) analog switch housed in a 16-pin VQFN (RGT) 3x3 mm package. Operating from 1.65 V to 4.3 V, it delivers low on-state resistance with excellent Ron matching across four independent 2:1 multiplexers and supports bidirectional signal flow on every channel. Two logic-level control inputs select between the NO/NC paths of all four switches simultaneously, simplifying firmware-driven signal routing. An analog switch is a solid-state semiconductor device that routes analog or digital signals between two or more terminals under the control of a logic-level signal. It belongs to the analog switch and multiplexer family, which sits inside the broader interface IC category of integrated circuits. Quad SPDT switches are commonly used to swap between two sources on four channels at once, an arrangement also called a 2-channel DPDT function in this device. Key features include 0.45 Ω typical on-state resistance, 50 pA typical switch leakage, break-before-make switching to prevent momentary channel cross-connection, and a -3 dB bandwidth greater than 35 MHz. The control inputs are 1.8 V logic-compatible, while supply operation extends from 1.65 V to 4.3 V. ESD protection on the switch pins exceeds 2000 V per the HBM model. Architecturally the part uses CMOS transmission gates with integrated charge-pump-derived well biasing, enabling low Ron and rail-to-rail signal swing on a single positive supply. Ron flatness is held tight across the input common-mode range, which preserves harmonic distortion performance in audio paths. The device draws only microamps of quiescent current, which is essential for battery-powered systems. Typical applications include portable audio routing between headphone jack and Bluetooth receiver, USB 2.0 high-speed signal switching, SPI/I²C bus multiplexing, smartphone audio codec path selection, and PDA or portable media player source switching. Industrial uses include 4-wire resistance measurement multiplexing and analog front-end signal routing. When designing with this part, ensure that the logic-high level on IN1/IN2 exceeds 0.85 x VDD and the logic-low is below 0.15 x VDD to guarantee full CMOS-level switching. Place 0.1 µF bypass capacitors within 5 mm of the VDD pin to keep digital control noise out of the analog path. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical PCB layout guidance not found in the manufacturer datasheet alone.

Devis Contact
TS3A4741DCNR - 0.9Ω Dual SPST Analog Switch | TI SOT-23-8
TS3A4741DCNR

TS3A4741DCNR - 0.9Ω Dual SPST Analog Switch | TI SOT-23-8

The Texas Instruments TS3A4741DCNR is a 0.9 Ω low on-resistance, low-voltage, single-supply, dual single-pole single-throw (SPST) analog switch housed in an 8-pin SOT-23 (DCN) package. It integrates two independent normally open (NO) switches, each with a 1:1 (SPST) topology, designed for 1.8 V logic compatibility when operated from a single 3 V supply rail. What is an SPST analog switch? An SPST (Single-Pole Single-Throw) analog switch is a solid-state semiconductor device that routes analog signals by electrically connecting or isolating one signal path. The TS3A4741 belongs to the broader category of analog switches and multiplexers, a subfamily of interface ICs used for signal routing in mixed-signal and low-power systems. Compared with mechanical relays, analog switches offer far faster switching speeds, lower power, smaller PCB area, and no mechanical bounce, at the cost of lower absolute voltage and current handling. Key specifications include a 0.9 Ω typical on-resistance (Ron), 1.8 V CMOS-compatible digital logic inputs, rail-to-rail analog signal handling, very low quiescent current, and integrated ESD protection. The two switches operate completely independently, allowing them to be used as separate signal paths or as complementary paths in a single function. The device is fabricated in a CMOS process and supports fast switching speeds, low off-leakage current, and bidirectional analog signal flow. Its small SOT-23-8 footprint and 1.8 V logic compatibility make it well suited to portable and battery-powered designs. Typical applications include audio signal routing in portable devices, switching between two sensors in handheld instruments, power rail multiplexing in low-power systems, and general-purpose signal gating in test equipment and consumer electronics. When designing with the TS3A4741, ensure the analog signal stays within the supply rails to avoid distortion or excessive leakage, and add 0.1 µF decoupling close to VCC. For applications requiring normally closed (NC) switches, use the pin-compatible TS3A4742. This page synthesizes verified distributor pricing, same-brand and cross-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
TS3A4751PWR - 0.9-Ohm Quad SPST Analog Switch | Texas Instruments
TS3A4751PWR

TS3A4751PWR - 0.9-Ohm Quad SPST Analog Switch | Texas Instruments

The Texas Instruments TS3A4751PWR is a bidirectional, 4-channel, normally-open (NO) single-pole single-throw (SPST) analog switch in a 14-pin TSSOP package. It operates from a single 1.6V to 3.6V supply, delivers a maximum on-state resistance of 0.9 ohm at a 3V supply, and handles rail-to-rail analog signals with fast switching speeds and very low quiescent power. An analog switch is an IC that routes or isolates analog signal paths under digital control. Within the signal-routing hierarchy, the TS3A4751 belongs to the SPST switch family, a subset of analog switches and multiplexers used in signal conditioning and power-management systems. Key features include 0.9-ohm maximum Ron at 3V (1.5-ohm maximum at 1.8V), Ron flatness of 0.4-ohm maximum at 3V, and Ron matching of 0.05-ohm maximum at 3V. The 1.8-V CMOS-compatible digital inputs allow direct interface with low-voltage GPIO when using a 3-V supply, eliminating level-shift circuitry. The device is available in 14-pin TSSOP (PW), 14-pin VQFN (RGY), and 2x2-mm micro X2QFN (RUC) packages. The low Ron supports power-switching and low-distortion signal paths, while rail-to-rail operation preserves full signal swing on 1.8V, 2.5V, and 3.3V rails. Typical applications include low-voltage power switching, audio signal routing in portable devices, battery-powered test points, and general-purpose signal muxing in smartphones, tablets, and industrial sensing modules. Its normally-open configuration makes it suitable for fail-safe, default-disconnected paths. When designing, remember that Ron rises at lower supply voltages: at a 1.8-V supply the maximum Ron is 1.5 ohm, so account for insertion loss and on-resistance flatness in high-fidelity or precision-current paths. According to TI datasheet, the TS3A4751 is the NO-switch counterpart within the TI low-voltage quad SPST family.

Devis Contact
TS3A5018PWR - 10-Ohm Quad SPDT Analog Switch | Texas Instruments
TS3A5018PWR

TS3A5018PWR - 10-Ohm Quad SPDT Analog Switch | Texas Instruments

The Texas Instruments TS3A5018PWR is a quad single-pole double-throw (SPDT) analog switch designed to operate from a 1.8V to 3.6V supply in a 16-pin TSSOP (PW) package rated from -40C to +85C. It handles both digital and analog signals, and signals up to V+ can be transmitted in either direction. An analog switch is a semiconductor device that selectively connects or disconnects an analog signal path under digital control. It is a fundamental signal-routing building block in the broader family of multiplexers, demultiplexers, and interface ICs. Analog switches provide a low-resistance path when ON and a high-impedance path when OFF, replacing bulky mechanical relays in audio/video routing, data acquisition, and communication systems. Key features include the wide 1.8V to 3.6V operating range (ideal for battery-powered and 3.3V systems), low 10-ohm ON-state resistance with excellent channel-to-channel matching, and low charge injection that minimizes glitches during switch transitions. All four SPDT switches share a common enable function so the entire device can be disabled to reduce power consumption. The TS3A5018 is built on TI CMOS process technology, providing low quiescent power dissipation and high reliability. Bidirectional signal flow means either of the two throw terminals can serve as the port, essential for multiplexing and demultiplexing on the same hardware. Turn-on and turn-off times are fast, supporting high-speed signal routing in data converters and communication interfaces. Typical applications include audio signal routing in portable devices, battery-powered data acquisition front ends, communication interface switching, and test equipment signal multiplexing. The low power consumption and wide supply range make it well suited for portable and industrial designs. Design consideration: the 10-ohm ON resistance introduces series attenuation in high-impedance circuits, so prefer low-impedance loads or buffer the switched node. Place a 0.1uF decoupling capacitor close to the V+ pin, and use the enable pin in battery designs to cut standby current when switching is idle.

Devis Contact
TS3A5018QPWRQ1 - 10-Ohm Quad SPDT Analog Switch | Texas Instruments
TS3A5018QPWRQ1

TS3A5018QPWRQ1 - 10-Ohm Quad SPDT Analog Switch | Texas Instruments

The Texas Instruments TS3A5018QPWRQ1 is an automotive-qualified (AEC-Q100) quad single-pole double-throw (SPDT) analog switch designed to operate from a 1.8V to 3.6V supply. Packaged in a 16-pin TSSOP (PW), it provides four independent SPDT switches with a low 10-ohm on-resistance, handling both digital and analog signals up to V+ in either direction. An analog switch (also called an analog multiplexer/demultiplexer or bidirectional switch IC) is a semiconductor device that routes analog or digital signals through a MOSFET transmission gate controlled by a digital select input. Analog switches sit within the broader signal-routing hierarchy: analog switch IC -> signal multiplexer -> interface and switching IC -> analog signal chain. They are fundamental building blocks wherever a processor must dynamically reconfigure signal paths without degrading signal integrity. Key features of the TS3A5018QPWRQ1 include the low 10-ohm typical on-resistance, wide 1.8V to 3.6V single-supply operation suited to battery-powered and low-voltage systems, full rail-to-rail signal handling, and break-before-make switching that prevents momentary shorting of signal sources. The Q1 suffix denotes AEC-Q100 qualification for automotive environments, with an extended operating temperature range supporting under-hood and body electronics applications. The device uses CMOS transmission-gate architecture, which keeps on-resistance relatively flat across the signal range and minimizes signal distortion for audio and data-routing tasks. Because signals up to V+ can pass in either direction, the switches work equally well for multiplexing and demultiplexing, such as sharing a codec between microphone and headset paths or switching antenna and test signals. Typical applications include automotive infotainment audio routing, battery-management cell-monitoring multiplexing, portable instrument signal switching, and general-purpose I/O expansion in industrial control boards. Design tip: minimize RON signal loss by keeping source impedance low, and always provide a solid V+ decoupling capacitor (0.1uF close to the pin). Remember that the analog signal range is limited to the 0V-to-V+ supply window; signals outside this range must be blocked or level-shifted.

Devis Contact
TS3USB3000MRSER - DPDT USB 2.0/MHL Switch | TI | UQFN-10
TS3USB3000MRSER

TS3USB3000MRSER - DPDT USB 2.0/MHL Switch | TI | UQFN-10

The Texas Instruments TS3USB3000MRSER is a double-pole, double-throw (DPDT) analog switch that combines a USB 2.0 High-Speed (480 Mbps) switch and a Mobile High-Definition Link (MHL) switch in a single 10-pin UQFN (RSE) package measuring 1.5 mm × 2.0 mm. It supports a -3 dB bandwidth of 6.1 GHz on the MHL path and operates from a 2.3 V to 4.8 V supply. The device is designed to share a common USB or Micro-USB connector between USB 2.0 data and MHL video signals in mobile phones, tablets, and portable media devices. A USB switch IC is a special-purpose analog multiplexer that routes high-speed differential signals between a single downstream port and two upstream paths (host vs. MHL sink). In the hierarchy of power management and signal routing components, this part belongs to the USB interface IC category, sitting between the connector and the application processor. DPDT switches such as the TS3USB3000 are critical because they must pass 480 Mbps USB signals and up to 3 GHz MHL content with minimal insertion loss, low crosstalk, and high off-isolation. Key features of the TS3USB3000 include low on-resistance (Ron) on the USB data paths, low on-capacitance (Con) for high-bandwidth signal transmission, 1.8-V-compatible select pins for direct GPIO control from a mobile processor, and a quiescent current of approximately 5 uA. The wide supply range (2.3 V to 4.8 V) covers both 3.3 V system rails and the typical 3.8 V Li-ion battery range without additional regulation. The small 1.5 mm × 2 mm UQFN footprint makes it ideal for space-constrained mobile applications. The TS3USB3000 uses a charge-pump-less architecture with simple CMOS logic-level select inputs. The two select pins (S1 and S0 per TI documentation) determine whether the common port is routed to the USB path or the MHL path. Internal ESD protection on the signal pins improves robustness against connector-level transients, which is critical for hot-plug consumer electronics. Typical applications include smartphones and tablets with MHL-enabled video output, automotive infotainment systems that mirror mobile content via USB or MHL, portable media players, and USB/MHL dongles. The wide bandwidth also makes it suitable for any system needing to multiplex two high-speed differential pairs onto a single connector. When designing with this part, place the device as close as possible to the USB/MHL connector to minimize stub lengths and signal-integrity degradation. Use controlled-impedance differential routing (90 ohm) on both sides of the switch, and provide adequate ground stitching vias along the signal path to maintain return-current continuity. This page synthesizes distributor pricing, pin-compatible alternatives, and practical design notes that are not aggregated in any single manufacturer datasheet or distributor catalog page.

Devis Contact
TS512ID - 3 MHz Precision Dual Op Amp | STMicroelectronics
TS512ID

TS512ID - 3 MHz Precision Dual Op Amp | STMicroelectronics

The STMicroelectronics TS512ID is a precision dual operational amplifier with two independent amplifiers, a 3 MHz gain-bandwidth product, and a maximum input offset voltage of 500 µV. The device is supplied in an 8-pin SOIC package and operates from single or dual power supplies, making it suitable for signal-conditioning and instrumentation applications requiring two amplifiers in one package. An operational amplifier is an analog integrated circuit that uses very high open-loop gain to amplify the difference between its inverting and non-inverting inputs. Precision operational amplifiers are a subtype of voltage-feedback amplifiers characterized by low offset voltage, low distortion, low noise, and stable operation with feedback. The dual-amplifier configuration places two amplifiers in one package, reducing board area and simplifying paired signal-processing circuits. The TS512 family provides a 3 MHz gain-bandwidth product, low input offset voltage of 500 µV maximum, low power consumption, short-circuit protection, low distortion, low noise, high channel separation, and internal ESD protection. According to the STMicroelectronics family datasheet, the minimum slew rate is 0.8 V/µs for TS512 and TS512A. The related TS512B has a guaranteed higher minimum slew rate of 1.072 V/µs. The TS512 family uses internal frequency and phase compensation to support stable operation in voltage-follower configurations. This is useful in application circuits where one amplifier buffers a source and the other performs gain or filtering. Its dual supply range is ±1.5 V to ±15 V, while single-supply operation is supported from 3 V to 30 V, allowing use in both conventional analog circuits and higher-voltage industrial interfaces. Typical uses include sensor-signal conditioning, low-level instrumentation, active filtering, audio preamplification, and general analog signal processing. The dual channel can implement matched buffer, gain, summing, or differential stages. Because offset voltage influences accuracy near the zero-voltage operating point, input-source resistance and bias-current compensation should be evaluated carefully. PCB layout should keep input and feedback paths short and place input compensation or filtering components close to the relevant amplifier pins. Both channels should share stable supply decoupling, while avoiding current paths through analog ground that carry output or digital return current. The SOIC package is suitable for conventional surface-mount assembly and conventional thermal design at low to moderate output current. This page consolidates the verified manufacturer-family information, distributor listing details, package data, sourcing information, and engineering guidance for TS512ID. It distinguishes documented TS512-family characteristics from unavailable detailed electrical limits and clearly identifies uncertainty where the supplied source data does not provide a defensible value.

USD $0,43 En stock
TS512IN - 3MHz Dual Precision Op Amp | STMicroelectronics
TS512IN

TS512IN - 3MHz Dual Precision Op Amp | STMicroelectronics

The STMicroelectronics TS512IN is a precision dual operational amplifier with a 3 MHz gain-bandwidth product, 1.5 V/µs slew rate, and a maximum input offset voltage of 500 µV, supplied in an 8-pin Mini DIP package. It is designed for general-purpose instrumentation, analog signal conditioning, and dual-channel measurement applications where two amplifiers share the same package. A dual operational amplifier is an analog integrated circuit containing two independent amplifier channels. Operational amplifiers are voltage amplifiers whose behavior depends mainly on external feedback components. The TS512IN combines frequency-compensated amplifiers for stable voltage-follower operation, low distortion, low noise, short-circuit protection, and internal ESD protection. The 3 MHz gain-bandwidth product supports useful closed-loop bandwidth well below 3 MHz at higher noise gains, while the 1.5 V/µs slew rate improves response to larger transient signals. A maximum offset voltage of 500 µV helps reduce DC error in precision feedback networks. Its dual-channel organization reduces package count and simplifies PCB routing when two amplified signals must be processed under shared supply conditions. The device operates from single 6 V to dual ±15 V supplies, matching conventional analog and industrial voltage ranges. Internal phase compensation allows voltage-follower use without an external compensation network. Short-circuit protection limits the effects of output overload, although sustained shorts still require appropriate supply and thermal checks. Internal ESD protection improves handling robustness without eliminating the need for normal assembly precautions. TS512IN applications include sensor-interface amplification, low-frequency instrumentation, dual audio-channel control, buffering, active filtering, and general analog signal conditioning. Designers should place input and feedback components close to their associated pins, observe the specified common-mode and output-current limits, and avoid excessive loading near the bandwidth and slew-rate limits. This product page combines verified manufacturer-linked specifications, source URLs, package information, application guidance, and honest comparison limitations. It distinguishes confirmed TS512IN attributes from parameters that require verification before a PCB or production cross-reference is approved.

Devis Contact
TS514ID - High-Speed Precision Quad Op Amp | STMicroelectronics
TS514ID

TS514ID - High-Speed Precision Quad Op Amp | STMicroelectronics

STMicroelectronics TS514ID is a high-speed, precision quad operational amplifier with four amplifier circuits, internally compensated frequency and phase response, short-circuit protection, internal ESD protection, and a 14-pin SOIC package. The verified product data identifies a maximum offset voltage of 500 uV and highlights a high gain-bandwidth product, low distortion, low noise, low power consumption, and high channel separation. The TS514ID is intended for instrumentation and general-purpose precision signal-processing designs requiring four amplifiers in one package. An operational amplifier, commonly called an op amp, is a voltage-controlled differential amplifier with very high open-loop gain. Its external feedback network determines the closed-loop behavior. The TS514 belongs to the operational-amplifier hierarchy, which includes instrumentation amplifiers, buffer amplifiers, comparators, and general-purpose voltage amplifiers. Internal phase compensation allows the TS514 to operate as a voltage follower despite its high gain-bandwidth product, reducing the external compensation effort required in many designs. The quad architecture integrates four amplifier channels into one 14-pin SOIC-14 package. Verified manufacturer-related product descriptions identify low offset voltage, low power consumption, short-circuit protection, low distortion, low noise, high gain-bandwidth product, high channel separation, and internal ESD protection. These characteristics make the device applicable to precision buffering, signal conditioning, instrumentation, industrial measurement, and general analog signal-processing systems. Each amplifier requires stable supply decoupling and careful handling of output-current limits. The TS514 uses internal frequency and phase compensation. This architecture is particularly useful in follower and precision-gain configurations because the compensation is already incorporated into the device. Its high speed does not eliminate the need for short feedback traces, adequate grounding, and supply bypassing. Designers should avoid long output routing and place input, output, and ground returns so that parasitic capacitance does not degrade stability or transient response. Typical uses include four-channel sensor conditioning, low-level signal amplification, active filtering, voltage buffering, and instrumentation chains requiring several matched amplifier functions. Industrial control and test equipment can also use the quad package to reduce board area compared with four discrete single-amplifier packages. Where precision offset and noise dominate, the complete manufacturer datasheet should be consulted for test conditions and application-specific limits. The principal design trade-off is speed versus power and stability margin. Although the TS514 supports high-speed operation and voltage-follower use, board layout, capacitive loading, output-current demand, and supply bypassing remain critical. A short, low-inductance layout with local decoupling is recommended. Application notes and the manufacturer datasheet should control the final compensation, grounding, and thermal implementation. This product page combines verified distributor and datasheet information with practical guidance on precision analog design, package reuse, selection criteria, and drop-in alternatives. It also distinguishes confirmed TS514-family candidates from cross-package or merely functional substitutes so engineers can avoid redesigns that require PCB changes.

Devis Contact
TS514IN - Quad Precision Op Amp | STMicroelectronics | DIP-14
TS514IN

TS514IN - Quad Precision Op Amp | STMicroelectronics | DIP-14

The STMicroelectronics TS514IN is a high-performance quad operational amplifier with internal frequency and phase compensation, supplied in a 14-DIP package. The device contains four amplifier channels in one package and is designed for general-purpose instrumentation, signal-conditioning, and analog control applications where stable voltage-follower operation is useful. The verified manufacturer description identifies low offset voltage, low power consumption, short-circuit protection, low distortion, low noise, high gain-bandwidth product, high channel separation, and internal ESD protection as key features. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. A quad operational amplifier extends this architecture to four independent channels in one package, reducing board area and simplifying multi-channel designs. The TS514IN belongs to the broader operational-amplifier, analog-amplifier, signal-conditioning, and semiconductor hierarchy. The TS514IN's compensated architecture is intended to support stable operation as a voltage follower despite its high gain-bandwidth product. Internal compensation simplifies circuit design when unity-gain stability is required, while short-circuit protection improves robustness in conventional analog signal paths. Low offset voltage supports precision-oriented instrumentation, and low noise and low distortion are useful for audio and measurement front ends. Four channels make the device suitable for sensor signal conditioning, current-voltage conversion, active filtering, waveform shaping, instrumentation amplifiers, feedback networks, and general analog control loops. The 14-DIP package is appropriate for through-hole prototyping, educational systems, laboratory instruments, and industrial assemblies where a dual-inline footprint is preferred over a fine-pitch surface-mount package. The principal design consideration is to verify the supply-voltage limits, input common-mode range, output swing, input bias current, noise density, and load-current behavior against the manufacturer datasheet before finalizing a new design. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be tied to a defined voltage within the input common-mode range. This page consolidates the verified manufacturer and distributor information, package details, application guidance, technical limitations, and drop-in replacement analysis. It also identifies parameters that require confirmation from the complete TS514 datasheet rather than substituting unverified assumptions.

Devis Contact
TS522ID - Dual 15MHz Low-Noise Op Amp | STMicroelectronics
TS522ID

TS522ID - Dual 15MHz Low-Noise Op Amp | STMicroelectronics

The STMicroelectronics TS522ID is a monolithic dual operational amplifier optimized for precision audio signal processing. It provides two amplifiers, a 15 MHz gain-bandwidth product, a 7 V/µs slew rate, low-voltage noise of 4.5 nV/√Hz, and a maximum input offset voltage of 850 µV in an 8-pin SOIC package. The device operates from 5 V to 30 V over an industrial temperature range of -40°C to +125°C. An operational amplifier is a voltage-controlled differential amplifier that uses feedback to amplify the difference between two input voltages. The dual configuration places two amplifiers in one package, allowing stereo audio, balanced signal paths, active filtering, or independent measurement channels to share a common footprint. Within the broader semiconductor hierarchy, the TS522 belongs to the operational-amplifier family, the analog amplifier category, and the signal-conditioning IC hierarchy. The TS522 combines low input offset, low voltage noise, and high dynamic performance for audio-oriented designs. Its 850 µV maximum input offset voltage supports accurate signal amplification, while the 4.5 nV/√Hz voltage-noise density is particularly relevant when processing low-level microphone, musical-instrument, or line-level signals. A 15 MHz gain-bandwidth product provides useful bandwidth for audio and general-purpose precision applications, and the 7 V/µs slew rate improves large-signal response. Internally, each amplifier is configured around high-gain stages with internal ESD protection. The manufacturer datasheet reports low distortion of 0.002%, macromodel inclusion, and excellent frequency stability. These characteristics make the TS522 suitable for precision audio signal chains where low noise, low distortion, and predictable frequency response matter more than very low power consumption. Typical uses include stereo audio preamplification, active crossover filters, mixer input stages, microphone preamplifiers, audio buffer circuits, and low-level sensor-conditioning channels. Two amplifiers in the same 8-pin SOIC package can reduce board area in stereo designs, while the industrial temperature range supports industrial control, communications, and instrumentation equipment. Designers should verify the required supply headroom, input common-mode range, output swing, noise gain, and stability for the selected feedback network. Decoupling capacitors should be placed close to the supply pins, and sensitive audio inputs should use short traces with suitable grounding to minimize parasitic pickup. A SPICE macromodel is available for circuit simulation, but board-level stability and distortion should still be verified with real components. This page consolidates the verified TS522ID operating characteristics, sourcing links, application guidance, design cautions, and replacement information. It also distinguishes confirmed technical facts from parameters that were not present in the supplied source data, helping engineers make a defensible design decision without treating unverified values as guaranteed specifications.

Devis Contact