Produits (46 000+)

SN65HVD37DR - 3.3V Full-Duplex RS-485 Transceiver | TI
SN65HVD37DR

SN65HVD37DR - 3.3V Full-Duplex RS-485 Transceiver | TI

The Texas Instruments SN65HVD37DR is a low-power, 3.3V full-duplex RS-485/RS-422 transceiver housed in a 14-pin SOIC package. It combines a robust differential driver and a differential receiver to deliver 1/1 transceiver functionality for industrial multi-point and long-cable-run applications, with separate driver outputs and receiver inputs forming a true four-wire (full-duplex) bus port. An RS-485 transceiver is a bus-interface IC that converts a single-ended UART/CMOS logic signal into a differential signal suitable for transmission over twisted-pair copper cabling, while rejecting common-mode noise picked up along the cable. The RS-485 standard (TIA/EIA-485) supports multi-drop buses, high noise immunity, and long cable runs, and is widely used as the physical layer for industrial protocols such as Modbus RTU, PROFIBUS DP, BACnet MS-TP, DMX512, and NMEA 0183. The HVD37 family belongs to the 3.3V-supply segment, allowing direct connection to low-voltage microcontrollers and FPGAs without level shifters. Key specifications include a 3.3V nominal supply (3V to 3.6V operating range), 1/8 unit-load receiver input impedance that allows up to 256 nodes on a single bus, bus-pin ESD protection exceeding 15 kV HBM, data rates up to 25 Mbps, and a wide common-mode voltage range for harsh industrial environments. The driver and receiver can each be independently enabled, providing flexible half-/full-duplex and shutdown control; quiescent current is typically 1 mA in operation and the standby/shutdown mode draws under 1 uA typical. High receiver hysteresis (typ. 60 mV) delivers robust noise immunity on long cables. Architecturally, the device uses TI's HVD series bipolar/diffusion process with integrated ESD cells on the bus pins and thermal-shutdown protection on the die. Fail-safe receiver design guarantees a known logic-high output when the bus is idle, open, or shorted, eliminating the need for external biasing resistors in many designs. The combination of 3.3V supply, 1/8 unit loading, and 25 Mbps speed positions this part between slow fault-tolerant transceivers and high-speed isolated RS-485 devices. Typical applications include industrial fieldbus nodes (Modbus, PROFIBUS), motor-drive control boards, building-automation gateways (BACnet), solar inverter monitoring, smart-meter AMR modules, and any multi-drop RS-485 network requiring low standby power. Designers choose this part when both directions must be active simultaneously on separate pairs. Designers should add 100 nF decoupling close to VCC and a small TVS/termination network at the bus pins, and remember that 1/8 unit-load transceivers permit large node counts but still require proper cable termination (typically 120 ohm at both ends) and stub-length discipline. This page synthesizes distributor pricing, drop-in alternatives, and design notes not aggregated on any single distributor or manufacturer page.

Devis Contact
SN65HVD50D - 25Mbps RS-485/RS-422 Transceiver | Texas Instruments
SN65HVD50D

SN65HVD50D - 25Mbps RS-485/RS-422 Transceiver | Texas Instruments

The Texas Instruments SN65HVD50D is a high-output, full-duplex RS-485 and RS-422 interface transceiver designed for reliable point-to-point and multipoint communications. It operates from a 4.5 V to 5.5 V supply, supports signaling rates up to 25 Mbps, and combines one driver with one receiver in an 8-pin SOIC package. The device includes selectable driver transition-time options for 1 Mbps, 5 Mbps, and 25 Mbps signaling, allowing designers to balance transmission distance, signal integrity, and electromagnetic compatibility requirements. An RS-485 transceiver is an interface IC that converts logic-level signals into differential bus voltages and receives differential bus signals back into logic-level outputs. This product belongs to the broader RS-485 transceiver family, which is part of the interface IC category and supports industrial, telecommunications, building automation, instrumentation, and data-communication equipment. The SN65HVD50D is appropriate where a system requires a dedicated full-duplex RS-485 or RS-422 interface rather than a half-duplex transceiver. Key features include 1/8 unit-load operation for networks containing as many as 256 nodes, bus-pin ESD protection exceeding 15 kV HBM, and a low-current standby mode with 1 µA typical standby current. The receiver provides 50 mV hysteresis, which helps improve noise immunity during differential signaling. The 25 Mbps maximum data rate makes the device suitable for high-speed data links where cable length and topology must be considered carefully. The SN65HVD50D is a single-channel transceiver with separate transmit and receive paths, allowing full-duplex communication. Its high-output driver is intended for driving differential cables and interconnects while maintaining robust signal margins. The manufacturer product page identifies the device as a High Output Full-Duplex RS 485 Driver and Receiver, while distributor listings identify the package as 8-SOIC and describe it as an RS-422/RS-485 interface IC. Typical applications include industrial control networks, factory automation equipment, instrumentation systems, building-control networks, and high-speed industrial data links. When selecting it, engineers should verify cable length, node count, termination, common-mode range, grounding, and connector requirements against the complete manufacturer datasheet before layout release. A practical design consideration is that the driver transition-time setting affects edge rate and therefore can influence EMI behavior. Keep the differential pair routed with controlled geometry, provide the required bus protection and termination, and validate the complete board-level signal integrity at the selected data rate. This page combines manufacturer and distributor information with application guidance, comparison criteria, and drop-in replacement findings to support faster engineering evaluation.

Devis Contact
SN65HVD51D - 5Mbps Full-Duplex RS-485 Transceiver | Texas Instruments
SN65HVD51D

SN65HVD51D - 5Mbps Full-Duplex RS-485 Transceiver | Texas Instruments

Texas Instruments SN65HVD51D is a high-output, full-duplex RS-422/RS-485 interface transceiver with one driver and one receiver, a maximum signaling rate of 5 Mbps, a 4.5 V to 5.5 V supply range, and an 8-pin SOIC package. The device provides separate driver and receiver paths for balanced industrial communications. An RS-485 transceiver is an interface IC that converts logic-level signals into differential bus signals and converts received differential signals back into logic levels. It belongs to the communication-interface hierarchy: RS-422/RS-485 transceiver, differential line driver and receiver, interface IC, and semiconductor. This signal conversion allows equipment to communicate reliably over longer cable runs, especially in industrial environments where common-mode noise and ground-potential differences can disrupt single-ended signaling. Key features include a one-eighth unit-load option supporting as many as 256 nodes on a bus, bus-pin electrostatic-discharge protection exceeding 15 kV HBM, and optional driver output transition times for 1 Mbps, 5 Mbps, and 25 Mbps signaling. The SN65HVD51D also supports a low-current standby mode below 1 µA and provides glitch-free operation. Its high-output design is intended for industrial communication and data-transmission systems using balanced transmission lines. The SN65HVD51 family operates from a 5 V supply and is offered in an 8-pin SOIC package. The D ordering option is specified for operation from -40 °C to 85 °C. According to the Texas Instruments product information, the SN65HVD51, SN65HVD50, and SN65HVD52 are fully enabled and have no external enable pins, allowing continuous operation without external driver or receiver control. The D suffix identifies the 8-pin SOIC package rather than a different transceiver function. Typical applications include industrial automation controllers, factory data-acquisition equipment, remote sensor interfaces, building-control systems, and communications equipment operating in electrically noisy environments. Full-duplex operation permits simultaneous transmission and reception on separate differential pairs, while the one-eighth unit-load capability helps designers connect more nodes than a conventional one-unit-load receiver would support. When laying out a board, use a controlled-impedance differential pair for each bus direction, provide a continuous ground reference, and place termination, protection, and common-mode components at the physical bus interface. Supply decoupling should be placed close to the device. Because RS-485 communication quality also depends on cable characteristics, grounding, topology, and termination—not only the transceiver—validate the complete channel in the target environment. This page combines verified Texas Instruments product information, distributor availability references, cross-reference results, and practical engineering guidance. It also distinguishes the confirmed pin-compatible THVD1451 replacement from same-family Texas Instruments alternatives whose enable and electrical characteristics require board-level verification before substitution.

Devis Contact
SN65HVD52D - 1 Mbps Full-Duplex RS-485 Transceiver | Texas Instruments
SN65HVD52D

SN65HVD52D - 1 Mbps Full-Duplex RS-485 Transceiver | Texas Instruments

The Texas Instruments SN65HVD52D is a high-output, full-duplex RS-485 driver and receiver interface IC operating at a 1 Mbps data rate. It is packaged in an 8-pin SOIC (D) and provides one driver and one receiver for balanced RS-422 and RS-485 communications. The device is intended for industrial, instrumentation, communications, and data-acquisition systems where a low-noise differential physical-layer interface is required. According to the manufacturer product page, SN65HVD52D is a High Output Full-Duplex RS-485 Driver and Receiver in an 8-pin SOIC package. An RS-485 transceiver is a physical-layer interface device that combines a differential line driver with a differential line receiver. The driver converts a single-ended logic signal into a balanced differential signal, while the receiver converts the differential bus voltage back into a logic signal. Full-duplex operation provides separate transmit and receive paths, allowing a system to transmit and receive simultaneously when the bus wiring and protocol support it. This makes the SN65HVD52D suitable for point-to-point links, multidrop RS-422 systems, and full-duplex RS-485 networks. The SN65HVD52D is specified for operation from a 5 V supply and supports signaling rates up to 1 Mbps. The SN65HVD5X family includes low-current standby operation, glitch-free operation, and selectable driver transition-time options for different signaling rates. The device also supports an eighth-unit-load option, allowing substantially larger bus populations than a standard unit-load transceiver when system capacitance and topology permit. Bus-pin ESD protection exceeds 15 kV HBM according to the device documentation. Typical applications include industrial automation links, programmable-logic-controller communication, factory-floor equipment, building-control networks, instrumentation, motor-control systems, and industrial data-acquisition equipment. The receiver is designed for balanced differential inputs, while the driver produces a high-output differential signal suitable for reliable communication over longer cable runs when the system uses proper termination and biasing. When designing around the SN65HVD52D, verify the data rate, cable length, topology, termination, and common-mode range together. The 8-pin SOIC footprint is compatible with conventional surface-mount assembly, but the exact pin function and enable or standby behavior must be checked in the manufacturer pin-description table. This page combines device specifications, practical application guidance, package information, and verified source links for engineering evaluation.

Devis Contact
SN65HVD53D - High-Output Full-Duplex RS-485 Transceiver | Texas Instruments
SN65HVD53D

SN65HVD53D - High-Output Full-Duplex RS-485 Transceiver | Texas Instruments

The Texas Instruments SN65HVD53D is a high-output, full-duplex RS-485 and RS-422 transceiver with driver and receiver enable pins, packaged in a 14-pin SOIC (D). It combines one differential driver and one differential receiver with independent active-high driver enable (DE) and active-low receiver enable (RE) control, and it offers a 1/8 unit-load receiver option supporting up to 256 nodes on a single bus. A transceiver is the physical-layer interface that converts between a logic-level digital signal and a balanced differential line pair. An RS-485 transceiver belongs to the differential line-driver / receiver family, which sits under interface ICs, communication ICs, and ultimately semiconductor ICs. Differential signaling carries the same data on two wires of opposite polarity, so common-mode noise induced along the cable is rejected by the receiver, making RS-485 the dominant industrial bus for factory automation, instrumentation, and building control. Key differentiators of this device include bus-pin ESD protection exceeding 15 kV HBM, selectable driver output transition times supporting signaling rates of 1 Mbps, 5 Mbps and 25 Mbps, a low-current standby mode drawing about 1 uA when both the driver and receiver are disabled, and glitch-free receiver outputs. The 14-pin SOIC body measures 3.90 mm wide and is rated for -40 C to +85 C operation, covering industrial temperature ranges without a hermetic or extended package. Internally, the SN65HVD53D uses a differential driver stage with selectable slew rate to control edge energy on the bus and limit EMI, while the receiver front end presents a low unit load so many nodes can share one cable run. Enable pins give the system designer direct control over bus direction and shutdown, which is valuable in multi-drop networks where multiple transceivers must not all drive simultaneously. Typical deployments include industrial RS-485 field buses, PLC and remote I/O links, building HVAC and access-control networks, utility and metering equipment, and instrumentation links where a full-duplex point-to-point topology with separate driver and receiver enables is required. When laying out the board, keep the differential pair tightly coupled with a continuous ground reference beneath it, place the bypass capacitors at the supply pins, and treat the enable pins as digital control signals that must be sequenced so that only one node drives the bus at a time. This page consolidates device specifications, enable-logic differences against sibling family members, drop-in alternatives, and practical layout guidance into a single engineering reference that goes beyond a basic catalogue entry.

Devis Contact
SN65HVD54D - 5 Mbps Full-Duplex RS-485 | Texas Instruments
SN65HVD54D

SN65HVD54D - 5 Mbps Full-Duplex RS-485 | Texas Instruments

The Texas Instruments SN65HVD54D is a high-output, full-duplex RS-485 driver and receiver with separate driver and receiver enables, operating from a single 5 V supply in a 14-pin SOIC (D) package. It supports signaling rates up to 5 Mbps, provides a 1/8-unit-load option for as many as 256 nodes on a bus, and includes bus-pin ESD protection exceeding 15 kV HBM. The device also offers a low-current standby mode with 1 µA typical standby current and selectable driver transition times optimized for 1 Mbps, 5 Mbps, and 25 Mbps signaling environments. An RS-485 transceiver is an interface integrated circuit that combines a differential line driver and differential receiver for balanced digital communications. It belongs to the RS-422/RS-485 transceiver hierarchy within interface ICs, where the driver translates logic-level signals into differential bus voltage and the receiver converts differential bus voltage back into a logic-level signal. Full-duplex operation provides separate paths for transmission and reception, making the SN65HVD54D suitable for systems that cannot share the same bus conductors in both directions. The SN65HVD54D provides one driver and one receiver, with independent enables that allow the system to place either side into a low-power state. Its high-output architecture is intended for demanding balanced-line links, while the selectable driver edge rates let engineers optimize signaling behavior for 1 Mbps, 5 Mbps, or faster communication links. The 1/8-unit-load receiver option can support up to 256 nodes, reducing the loading burden in large multi-node industrial systems. Bus-pin ESD protection exceeding 15 kV HBM adds an important ruggedness margin where cables and external connectors are exposed to electrostatic discharge. The device operates across the -40 °C to +85 °C temperature range in the SN65HVD54D ordering option. Its separate full-duplex driver and receiver structure is particularly useful when the transmitting and receiving nodes must remain active simultaneously. Typical uses include industrial factory automation, building-control networks, industrial instrumentation, motor-control systems, process monitoring, and other full-duplex RS-485 links. The 5 Mbps capability supports factory-floor communication, while the standby function can reduce consumption when a node is not communicating. Component placement and termination remain important because the transceiver does not eliminate the need for a balanced cable, appropriate bus topology, and correctly engineered termination. Designers should verify enable polarity in the host logic, place the device close to the bus connector, and provide protection appropriate to the installation environment. The internal high-impedance state supports controlled bus participation, but software and fault-management circuitry must still prevent multiple transmitters from driving the same bus at the same time. This page consolidates verified manufacturer and distributor information, package details, lifecycle attributes, replacement guidance, and application-oriented engineering context. It also distinguishes documented drop-in family options from alternatives that may require different packages or interface behavior, helping engineers shorten component-selection and PCB-validation work.

Devis Contact
SN65HVD55D - 1Mbps Full-Duplex RS-485 | Texas Instruments
SN65HVD55D

SN65HVD55D - 1Mbps Full-Duplex RS-485 | Texas Instruments

The Texas Instruments SN65HVD55D is a high-output, full-duplex RS-485 driver and receiver with enables, supporting data rates up to 1 Mbps and operation from -40°C to +85°C in a 14-pin SOIC package. It provides a 1/8-unit-load option for networks containing as many as 256 nodes, 50 mV receiver hysteresis for improved noise immunity, and bus-pin ESD protection exceeding 15 kV HBM. An RS-485 transceiver is a bidirectional communications interface that combines a differential line driver, a differential receiver, and associated enable controls. It belongs to the interface-IC hierarchy and enables robust communication over long, noisy cables by representing digital data as a differential voltage across a balanced pair of conductors. The SN65HVD55D uses separate driver and receiver paths, allowing full-duplex operation on a four-wire bus. Key features include a maximum data rate of 1 Mbps, 1/8-unit-load operation, and optional driver transition times intended for signaling rates of 1 Mbps, 5 Mbps, and 25 Mbps. The low-current standby mode consumes 1 µA, making the enables useful for power-conscious systems. Bus-pin ESD protection exceeding 15 kV HBM helps improve robustness where cables connect the transceiver to external equipment. The high-output architecture increases the amount of signal energy available on the bus, while the receiver's 50 mV hysteresis rejects noise within the transition region between differential output states. The device is suitable for RS-422 and RS-485 equipment where point-to-point or multipoint differential signaling is required. Its independent enable controls permit the driver and receiver to be switched according to the operating state of the connected system. Typical applications include industrial automation equipment, factory-floor controllers, building-control systems, data-acquisition equipment, communications modules, and external bus interfaces. In a full-duplex installation, the driver connects to one differential pair and the receiver connects to another pair, allowing simultaneous transmission and reception without sharing the same bus conductors. Designers should account for cable length, topology, termination, grounding, and the slew-rate option when selecting the device. The bus must remain within the transceiver's specified electrical limits, and unused inputs should be handled according to the manufacturer guidance. Enable sequencing should also prevent simultaneous bus contention where multiple nodes share a conductor pair. This product page combines the verified manufacturer description, distributor availability, package information, RS-485 operating characteristics, and documented family differences. It also provides application guidance and a structured comparison for engineers evaluating drop-in interface choices without adding unverified electrical claims.

Devis Contact
SN65HVD61D - Single-Channel ControlNet Transceiver | Texas Instruments
SN65HVD61D

SN65HVD61D - Single-Channel ControlNet Transceiver | Texas Instruments

Texas Instruments SN65HVD61D is a single-channel ControlNet physical-layer transceiver with one driver and one receiver, supplied in a 14-pin SOIC package. Designed for single-node operation and distributed stand-alone applications, it provides the circuitry required by ControlNet coaxial-based physical layers. Its pull-or-pull transmitter sinks current from a center-tapped transformer, supporting galvanic isolation between the transceiver circuitry and the external network interface. The combination of one integrated transceiver channel, transformer-compatible drive topology, and a compact 14-SOIC package makes the device applicable to industrial automation, controller, sensor, and factory-control networks. A ControlNet transceiver is a specialized interface IC that converts digital logic signals into a balanced physical-layer network connection and converts received network signals back into logic-level data. Within the product hierarchy, it belongs to the interface transceiver class, with ControlNet operation representing its defining protocol and physical-layer function. Its isolation-oriented transmitter arrangement is particularly useful where system designers require a transformer-based link between the transceiver and a coaxial cable network. The SN65HVD61D integrates one driver and one receiver into a single channel. The manufacturer describes the transmitter as a pull-or-pull arrangement that sinks current from a center-tapped transformer rather than driving the cable directly. This architecture allows the external transformer to establish the physical signal coupling and galvanic isolation. The 14-SOIC package supports conventional surface-mount assembly while providing a practical pin count for a complete single-channel interface. The primary system benefit is functional consolidation: one device contains both sides of the ControlNet physical-layer connection. This can reduce the number of separate interface components required for a single-node or stand-alone node. The galvanic-isolation capability provided by the center-tapped transformer arrangement is also important in industrial environments where isolation between the electronic circuitry and external cabling is a system requirement. Actual isolation voltage, data rate, supply range, and timing limits must be confirmed in the manufacturer datasheet before final qualification. Typical use cases include ControlNet-compatible programmable logic controllers, industrial automation controllers, remote I/O nodes, factory sensor interfaces, motor-control supervisory nodes, and distributed process-monitoring equipment. In each case, the SN65HVD61D handles the local logical transceiver function while a suitable center-tapped transformer connects the device to the ControlNet physical layer. The primary design consideration is transformer and network compatibility. The external center-tapped transformer must match the device's electrical and timing requirements, and its wiring must preserve the intended isolation boundary. PCB signal integrity, return paths, bypass-capacitor placement, and connector or cable characteristics also require careful implementation because the transceiver communicates through a coupled physical layer rather than a direct point-to-point logic interface. This page consolidates the verified manufacturer description, distributor identification, package information, sourcing links, and practical engineering guidance. It also distinguishes the SN65HVD61D from family ordering variants and identifies where additional electrical, timing, compliance, or lifecycle data must be obtained from the authoritative manufacturer documentation.

Devis Contact
SN65HVD70DGSR - 3.3V Full-Duplex RS-485 400kbps Transceiver, 10-VSSOP | Texas Instruments
SN65HVD70DGSR

SN65HVD70DGSR - 3.3V Full-Duplex RS-485 400kbps Transceiver, 10-VSSOP | Texas Instruments

The Texas Instruments SN65HVD70DGSR is a 3.3 V, full-duplex RS-485 transceiver rated for data rates up to 400 kbps, integrating ±12 kV IEC 61000-4-2 contact discharge ESD protection, in a 10-pin VSSOP (DGS) PowerPAD package. The device pairs one differential driver with one differential receiver, each with dedicated input/output pins, enabling simultaneous transmit and receive on a four-wire bus typical of RS-422 and full-duplex RS-485 networks. The driver includes active-high enable control and the receiver includes active-low enable control, allowing a sub-5 µA standby current when both functions are disabled. A transceiver of this class is the physical-layer interface between a UART/MCU and a differential twisted-pair cable in industrial multipoint networks. The SN65HVD70 extends TI's RS-485 portfolio as a low-power, robust 3.3 V member of the SN65HVD7x family, suitable for half- and full-duplex links across factory floors, building automation, and motor-drive backplanes. As a line transceiver it sits hierarchically below the protocol layer (Modbus, PROFIBUS, DMX512) and above the cable plant, converting CMOS/TTL logic levels into the differential A/B signaling defined by TIA/EIA-485-A and TIA/EIA-422-B. Key features include ±30 kV HBM ESD on the bus pins, a wide 3.0 V to 3.6 V supply range, a 1.8 V to 5 V logic interface (no level shifter needed in 1.8 V systems), open-circuit, short-circuit, and bus-idle fail-safe receiver inputs, and a thermal-shutdown protected driver. The 10-pin VSSOP package with thermal pad keeps the footprint compact while supporting industrial -40 °C to +125 °C operation. The device uses a precision differential architecture with large receiver hysteresis (typically 50 mV) to reject common-mode noise on long cable runs. The wide common-mode range of -7 V to +12 V tolerates ground potential differences between nodes, and the 1/8 unit-load option permits up to 256 nodes on a single bus. Slew-rate limiting reduces EMI reflections on unterminated stubs. Typical applications include industrial multi-drop RS-485 networks, building-automation backbones, motor-control command links, point-of-sale peripherals, and full-duplex RS-422 point-to-point data links. The device is well matched to long cable runs with proper 120 Ω termination at both ends. When designing with this part, place 100 nF decoupling capacitors within 2 mm of VCC and use a 120 Ω termination resistor at each end of the bus. Do not leave unused driver outputs floating - tie them to GND through a resistor. Maintain a 1/8 unit-load budget when scaling beyond 32 nodes. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including cross-vendor equivalents and full intent coverage in the FAQ for engineers planning second-source qualification.

Devis Contact
SN65HVD71D - 400kbps Full-Duplex RS-485 Transceiver | Texas Instruments
SN65HVD71D

SN65HVD71D - 400kbps Full-Duplex RS-485 Transceiver | Texas Instruments

Texas Instruments SN65HVD71D is a 3.3 V full-duplex RS-485 and RS-422 transceiver with one driver and one receiver, a 400 kbps data rate, and 12 kV IEC ESD protection. It is packaged in an 8-pin SOIC (D) package and operates without driver or receiver enable controls. The separate driver input and receiver output pins support simultaneous bidirectional communication on a multidrop industrial bus. An RS-485 transceiver is an interface integrated circuit that converts logic-level signals into differential bus signals and converts received differential signals back into CMOS-compatible logic. RS-485 extends communication distance and noise immunity compared with single-ended interfaces by using balanced differential signaling. This family belongs to the interface IC hierarchy: transceiver > RS-485 interface > differential bus interface > semiconductor. The SN65HVD71D provides a 3.3 V supply range of 3 V to 3.6 V, operation from -40 °C to +125 °C, and a data rate up to 400 kbps. Its 12 kV IEC-rated ESD protection helps protect the transceiver when cables are connected to external equipment. Full-duplex operation allows transmitting and receiving simultaneously, which is useful for point-to-point links and systems that cannot wait for a bus turnaround. Internally, the device combines one differential driver and one differential receiver. The driver accepts a CMOS-compatible transmit input, while the receiver produces a CMOS-compatible receive output. The absence of enable pins simplifies control logic, although the design must manage bus direction externally when the transceiver is connected to a shared multidrop network. Typical applications include industrial RS-485 links, building automation, factory equipment, motor-control systems, security equipment, and other long-distance serial networks. The device can also support point-to-point RS-422-style connections when the system requires independent transmit and receive paths. Designers should check the pin assignment and termination requirements in the manufacturer datasheet before layout. A 120-ohm termination resistor is commonly used at each end of a standard RS-485 bus, while bias resistors should be placed only where required. Keep the differential pair routed together, minimize stubs, and provide a stable return path to reduce common-mode noise. This product page combines the manufacturer's electrical specifications with practical interface guidance, application context, comparison information, and verified sourcing references. It is intended to help engineers identify whether the SN65HVD71D fits a 3.3 V full-duplex RS-485 design before beginning PCB implementation.

Devis Contact
SN65HVD72D - 3.3V 250kbps Half-Duplex RS-485 | Texas Instruments
SN65HVD72D

SN65HVD72D - 3.3V 250kbps Half-Duplex RS-485 | Texas Instruments

The Texas Instruments SN65HVD72D is a 3.3 V half-duplex RS-485 transceiver with IEC ESD protection and a maximum signaling rate of 250 kbps, packaged in an 8-pin SOIC (D) package. It combines one RS-485 driver and one RS-485 receiver in a single integrated circuit, making it suitable for bidirectional industrial communication links using differential bus wiring. The part is identified by Texas Instruments as an active product with an operating temperature range of -40 °C to 125 °C and RoHS-compliant construction. An RS-485 transceiver is an interface IC that translates between a logic-level UART or digital signal and a differential RS-485 bus. The differential architecture supports noise-resistant communication over longer cable runs than single-ended signaling, while the half-duplex arrangement allows the same pair of bus conductors to support both transmission and reception. In this device, the 3.3 V supply and 250 kbps data rate suit embedded systems, industrial controllers, sensors, and equipment using low-speed field-bus links. Key verified characteristics include a 3.3 V supply, 250 kbps maximum signaling rate, half-duplex operation, RS-422/RS-485 transceiver functionality, and IEC ESD protection. The SOIC-8 package provides a compact surface-mount footprint for industrial control boards and communication modules. The device is marketed for demanding industrial applications where robust bus interfacing and protection are important. The SN65HVD72D integrates the physical-layer functions needed to connect a microcontroller or programmable logic controller to a differential RS-485 network. Designers should pay attention to bus biasing, termination, grounding, cable length, and the exact logic-control requirements of the selected family variant. The manufacturer product page and part-details page are the authoritative sources for ordering information, electrical characteristics, and package details. Typical uses include industrial automation equipment, remote sensor interfaces, building-control systems, instrumentation, and embedded serial networks. Compared with lower-speed or more highly integrated interface solutions, the SN65HVD72D provides a focused 250 kbps half-duplex RS-485 solution with ESD protection in a standard 8-pin SOIC package. This page combines verified manufacturer and distributor information with practical selection guidance, pricing context, and application notes for engineers evaluating the SN65HVD72D.

Devis Contact
SN65HVD73D - 20Mbps Full-Duplex RS-485 | TI
SN65HVD73D

SN65HVD73D - 20Mbps Full-Duplex RS-485 | TI

The Texas Instruments SN65HVD73D is a 3.3 V full-duplex RS-485/RS-422 transceiver with a 20 Mbps maximum data rate, ±12 kV IEC ESD protection, and individual driver and receiver enables in a 14-pin SOIC (D) package. The device integrates one driver and one receiver, supports a 3 V to 3.6 V supply range, operates across -40°C to +125°C, and provides 70 mV receiver hysteresis. An RS-485 transceiver is a physical-layer interface IC that converts low-voltage digital logic signals into differential bus signals and reconstructs logic-level data from a differential bus. It belongs to the transceiver hierarchy within interface ICs and enables robust, point-to-point or multidrop communication over longer distances than single-ended logic interfaces. Full duplex means the driver and receiver can operate simultaneously on separate differential pairs. The SN65HVD73D's principal features include a 20 Mbps data rate, 70 mV receiver hysteresis, separate active-high driver enable and active-low receiver enable controls, and ±12 kV IEC-rated ESD protection. Its 3 V to 3.6 V operating range is appropriate for 3.3 V systems. The broad -40°C to +125°C temperature range supports industrial and extended-temperature equipment when the complete system qualification permits it. The integrated driver and receiver provide one RS-485/RS-422 communication channel in full-duplex configuration. Separate enables allow the transmitter and receiver to be disabled independently, and the manufacturer product page states that standby current can be reduced below 5 µA when both functions are disabled. A common ground reference and carefully terminated differential wiring remain necessary for reliable operation. Typical applications include industrial control networks, factory automation equipment, data acquisition systems, building-automation controllers, and communications between a host controller and a peripheral transceiver. The 20 Mbps capability supports high-speed point-to-point links, while the ±12 kV IEC ESD rating helps protect external bus connectors in electrically noisy environments. Designers should follow the manufacturer datasheet for transceiver pinout, termination, fail-safe biasing, and differential routing. Keep the RS-485 differential pair routed as a controlled-impedance pair, minimize stub lengths, place termination only where required by the bus topology, and verify grounding and surge-protection requirements for the installed environment. This product summary consolidates verified manufacturer and distributor information, supply parameters, design guidance, and replacement constraints into one engineering-focused reference. It also clearly distinguishes verified specifications from electrical values that require confirmation from the complete datasheet before schematic release.

Devis Contact
SN65HVD73DGS - 3.3V Full-Duplex RS-485 20Mbps | Texas Instruments
SN65HVD73DGS

SN65HVD73DGS - 3.3V Full-Duplex RS-485 20Mbps | Texas Instruments

The Texas Instruments SN65HVD73DGS is a 3.3 V full-duplex RS-485 transceiver with integrated active-high driver enable and active-low receiver enable pins, supporting data rates up to 20 Mbps in a 10-pin VSSOP (DGS) package. It integrates a differential driver, a differential receiver, and 12 kV IEC ESD protection on bus pins, operating from a single 3.3 V supply across the industrial -40°C to +125°C temperature range. The device is designed for high-speed, half-duplex-to-full-duplex RS-485 networks in industrial automation, motor control, and point-to-point data links. A RS-485 transceiver is a balanced differential line driver/receiver IC that converts a single-ended TTL/CMOS logic signal into a differential signal conforming to the TIA/EIA-485-A standard, enabling robust multi-drop communication over twisted-pair cable with common-mode voltage tolerance up to ±25 V and cable lengths up to 1200 m at reduced data rates. RS-485 transceivers sit within the broader hierarchy of interface ICs, bridging UART/MCU logic with physically robust fieldbus wiring. The SN65HVD73DGS belongs to the 3.3 V HVD7x family, which the manufacturer offers in both SOIC and small-footprint MSOP/VSSOP packages for space-constrained designs. Key features include 12 kV IEC 61000-4-2 ESD protection on bus pins (HBM and contact discharge), 20 Mbps signaling rate for Profibus and high-speed fieldbus use, 1/8 unit-load receiver input impedance for up to 256 nodes on a single bus, and separate driver/receiver enable pins for half-duplex reuse even though the device is full-duplex. The receiver failsafe design guarantees a logic-high output when the bus is idle, shorted, or terminated but undriven. The bus pins survive ±25 V common-mode transients common in industrial environments. Architecturally, the SN65HVD73DGS uses a 3.3 V CMOS core with a symmetric differential driver output stage and a wide-common-mode differential receiver, internally synchronized to share a single 3.3 V supply rail. The driver slew rate is optimized for 20 Mbps NRZ signaling, and the receiver hysteresis (typically 50 mV) ensures noise-immune operation over long cables. Internal ESD cells provide IEC-level protection without external TVS diodes in most applications. Typical applications include industrial fieldbus networks (Modbus RTU, Profibus DP, DMX512), motor-drive encoder feedback, solar inverter daisy-chain communication, building automation (BACnet MS/TP), and any 3.3 V logic node that must communicate over a long, electrically noisy cable. Pairing with a TVS diode such as SMAJ33CA extends transient protection beyond 12 kV. When designing with this part, ensure the bus is terminated with a 120 Ω resistor at each end and that stubs are minimized to preserve signal integrity at 20 Mbps. The active-high DE and active-low RE pins allow independent control of driver and receiver, supporting direction-switching protocols as well as fail-safe shutdown during bus faults. Decouple VCC with a 0.1 µF ceramic capacitor placed within 5 mm of the supply pin.

Devis Contact
SN65HVD73DGSR - 3.3V Full-Duplex RS-485, 20Mbps, 12kV ESD | TI
SN65HVD73DGSR

SN65HVD73DGSR - 3.3V Full-Duplex RS-485, 20Mbps, 12kV ESD | TI

The Texas Instruments SN65HVD73DGSR is a 3.3-V full-duplex RS-485 transceiver with separate driver and receiver pins, 20 Mbps signaling rate, and ±12-kV IEC 61000-4-2 contact ESD protection, housed in a 10-pin MSOP/VSSOP (DGS) package. The wide common-mode voltage range makes the device suitable for multi-point RS-485 / RS-422 bus applications over long cable runs in industrial, building automation, and motor-control networks. A RS-485 transceiver is a physical-layer interface IC that converts between a low-voltage UART/logic-level signal on the controller side and a balanced differential signal on the bus side. Full-duplex (a.k.a. 4-wire RS-485) uses separate differential pairs for transmit and receive, allowing simultaneous two-way communication. The SN65HVD73 belongs to the broader family of half- and full-duplex RS-485 transceivers -> differential line transceivers -> interface ICs -> integrated circuits in the data-communication hierarchy defined by TIA-485 / EIA-422 standards. Key features include 3.3-V single-supply operation (compatible with modern low-power MCUs and FPGAs), 20 Mbps maximum data rate, ±30-kV HBM and ±12-kV IEC 61000-4-2 contact-discharge ESD on bus pins, large receiver hysteresis for noise immunity in harsh industrial environments, 1/8 unit-load support that lets up to 256 nodes share one bus, and separate driver-enable (DE) and receiver-enable (RE) pins for direction control and half-duplex reuse. Operating temperature spans -40 °C to +125 °C. The architecture uses a differential line driver and differential line receiver with a wide common-mode range (typically -7 V to +12 V), allowing reliable communication in installations with large ground-potential differences. Internal slew-rate control and low bus-current loading support PROFIBUS, DMX512, and similar multi-drop protocols at 20 Mbps without external components. Typical applications include industrial field-bus nodes, motor encoder feedback links, building-automation gateways, solar inverter monitoring, and point-to-point backplane links between 3.3-V controllers. The wide common-mode range and IEC-grade ESD simplify compliance with industrial EMC requirements without external TVS arrays. When designing with this device, place the 100 nF VCC bypass capacitor as close to pin 10 as possible and use 120 Ω termination only at the two physical ends of the bus. Leave the middle of the bus unterminated to avoid loading reflections. The DE and RE pins let the host power-gate the part in sleep-mode designs by de-asserting both enables. This page synthesizes distributor pricing, drop-in alternatives from the TI SN65HVD7x family and cross-brand RS-485 ICs in the VSSOP-10 footprint, and practical design notes not found in the manufacturer datasheet alone.

Devis Contact
SN65HVD74D - 3.3V 20Mbps Full-Duplex RS-485 | TI
SN65HVD74D

SN65HVD74D - 3.3V 20Mbps Full-Duplex RS-485 | TI

The Texas Instruments SN65HVD74D is a 3.3 V full-duplex RS-485 transceiver with a 20 Mbps data rate, 12 kV IEC ESD protection, and an 8-pin SOIC package. It combines one differential driver and one differential receiver, providing separate data paths for simultaneous bidirectional communication over an RS-485 bus. The device supports a 3.0 V to 3.6 V supply range and operates from -40°C to 125°C. A transceiver interface IC converts between digital logic signals and balanced differential bus signals. The SN65HVD74 belongs to the RS-485 transceiver category within interface ICs, interface semiconductors, and broader communication semiconductors. Its differential signaling improves noise immunity by comparing the voltage between two bus conductors rather than referencing one conductor to ground, making it suitable for industrial, building-automation, and communications equipment operating over longer cable runs. The SN65HVD74D combines a 20 Mbps maximum data rate with more than 30 kV HBM ESD protection and more than 12 kV IEC61000-4-2 contact-discharge protection. Receiver hysteresis is 70 mV, helping reject conducted differential noise and prevent unwanted output transitions. Separate driver and receiver input and output pins support full-duplex bus arrangements without sharing a single half-duplex direction-control path. The transceiver operates from a single 3.3 V power supply and supports both RS-485 and RS-422 interface applications. Its surface-mount SOIC package permits automated assembly, while the stated -40°C to 125°C operating range supports industrial equipment, data-acquisition systems, factory controls, and industrial communication equipment. Each driver and receiver has separate input and output pins, allowing transmit and receive paths to operate simultaneously. Typical applications include full-duplex RS-485 industrial networks, high-speed instrumentation links, factory automation equipment, building-control systems, and industrial data acquisition. In a typical circuit, the microcontroller-facing pins connect to digital logic, while the differential A, B, Y, and Z pins connect to the balanced bus through suitable termination and protection components. The 70 mV receiver hysteresis helps maintain reliable decisions in electrically noisy environments. When designing the interface, maintain compatible logic levels, observe recommended bus biasing and termination, and verify that the selected cable length and topology remain valid for 20 Mbps operation. Protection-device capacitance should be included when calculating edge rate and channel performance. The 3.3 V supply must remain within the specified 3.0 V to 3.6 V range, and system designers should check all logic thresholds against their controlling device. This page combines the manufacturer's key electrical and environmental ratings with practical interface-design guidance, packaging information, and a focused drop-in replacement assessment. It highlights where the SN65HVD74D fits within a 3.3 V full-duplex RS-485 design and the checks that matter when evaluating bus speed, ESD robustness, receiver noise immunity, and PCB implementation.

Devis Contact
SN65HVD75D - 3.3V 20Mbps RS-485 Transceiver | Texas Instruments
SN65HVD75D

SN65HVD75D - 3.3V 20Mbps RS-485 Transceiver | Texas Instruments

Texas Instruments SN65HVD75D is a 3.3 V half-duplex RS-485 transceiver with IEC ESD protection and a maximum signaling rate of 20 Mbps, housed in an 8-pin SOIC package. It supports operation from -40°C to 125°C and accepts 5 V-tolerant logic inputs compatible with 3.3 V or 5 V controllers. An RS-485 transceiver is an interface IC that combines a differential line driver and differential receiver, allowing digital data to be transmitted reliably over balanced, multipoint communication buses. The SN65HVD75 belongs to the transceiver hierarchy of interface ICs, differential line-driver and receiver circuits, and industrial communication semiconductors. Its half-duplex configuration permits a shared pair of conductors to carry data in either direction, but only one direction at a time. The SN65HVD75D operates from a 3.3 V supply, reaches 20 Mbps, and provides IEC ESD protection on the bus pins. Its logic interface supports 3.3 V and 5 V controllers, which simplifies connection to mixed-voltage digital systems. The wide -40°C to 125°C temperature range also makes the device suitable for industrial environments where commercial-temperature interface ICs may be inadequate. Exact ESD ratings, receiver thresholds, and electrical limits must be confirmed in the manufacturer datasheet. Each device combines a differential driver and differential receiver operating from one 3.3 V power supply. The bus pins are designed for robust ESD-event handling, including Human Body Model and IEC Contact Discharge protection. The manufacturer datasheet also identifies 250 kbps, 20 Mbps, and 50 Mbps signaling-rate options across the SN65HVD7x family, with 20 Mbps specifically associated with the SN65HVD75. Typical uses include industrial automation controllers, factory data buses, industrial instrumentation, building automation, and communications equipment operating on RS-485 networks. Its 20 Mbps capability supports high-speed half-duplex links, while 5 V-tolerant logic inputs ease interfacing with both 3.3 V and 5 V controllers. The half-duplex arrangement also requires careful direction-control design because the driver and receiver share the same bus pair. When designing the circuit, place a 100 nF ceramic bypass capacitor close to the supply pins and use a 3.3 V source capable of supporting the transceiver's operating current. The manufacturer recommends the TPS76333 for a suitable 3.3 V supply and the SN6501 for isolated power-supply designs. Bus routing should minimize stubs and maintain controlled differential impedance. This page combines verified manufacturer and distributor information, transparent pricing-status notes, same-family replacement analysis, and practical RS-485 design guidance. It also distinguishes verified electrical facts from parameters that still require confirmation against the complete SN65HVD7x manufacturer datasheet.

Devis Contact
SN65HVD76D - 50Mbps Full-Duplex RS-485 | Texas Instruments
SN65HVD76D

SN65HVD76D - 50Mbps Full-Duplex RS-485 | Texas Instruments

Texas Instruments SN65HVD76D is a 3.3 V full-duplex RS-485 transceiver with a 50 Mbps data rate, separate driver and receiver enables, and 12 kV IEC contact-discharge ESD protection. It is packaged as a 14-pin SOIC for surface-mount industrial and instrumentation systems. An RS-485 transceiver combines a differential line driver and differential receiver to communicate reliably over noisy, long-distance industrial buses. The SN65HVD76 family supports both RS-485 and RS-422 applications, while its full-duplex architecture provides simultaneous transmit and receive paths through separate differential pins. It operates from a single 3.3 V power rail, simplifying integration with 3.3 V controllers, sensors, gateways, and test equipment. The principal features include a 50 Mbps maximum data rate, 1/8 unit-load receiver operation for up to 256 nodes, a 70 mV receiver hysteresis, and separate enable controls. According to the Texas Instruments product page, the driver enable is active high and the receiver enable is active low. Disabling both functions can reduce standby current to less than 5 uA, making the device useful in low-power distributed systems. Bus protection includes greater than 30 kV human-body-model protection and greater than 12 kV IEC 61000-4-2 contact-discharge protection, together with greater than 4 kV IEC 61000-4-4 fast-transient burst protection. These ratings help protect the transceiver in electrically noisy environments, although they do not eliminate the need for correct common-mode grounding, cable selection, and termination practices. Typical applications include industrial RS-485 links, factory automation equipment, building controls, instrumentation, and high-speed data acquisition. Full-duplex operation is particularly appropriate when continuous receiving is required while the controller also transmits status, configuration, or diagnostic data. The 14-pin SOIC format also supports conventional surface-mount assembly and thermal design. For a new layout, place the transceiver and its protection or bypass components near the bus connector, maintain a continuous ground reference with the cable, and apply termination only where required by the network topology. Verify that the selected logic controller can tolerate the receiver output levels and that the bus does not exceed the device's electrical limits. This page combines the exact device specifications, practical RS-485 design guidance, application fit, and package-level comparison information. It also distinguishes true board-level drop-in options from related family members whose enable behavior or transceiver configuration differs, helping engineers avoid selecting a substitute that requires schematic or layout changes.

Devis Contact
SN65HVD77D - 3.3V 50Mbps Full-Duplex RS-485 | Texas Instruments
SN65HVD77D

SN65HVD77D - 3.3V 50Mbps Full-Duplex RS-485 | Texas Instruments

Texas Instruments SN65HVD77D is a 3.3 V full-duplex RS-485 transceiver with a 50 Mbps data rate, ±12 kV IEC ESD protection, and an 8-pin SOIC package. It combines one differential driver and one differential receiver in a single package, allowing transmit and receive paths to operate simultaneously. The device operates from 3.0 V to 3.6 V and is specified across -40°C to 125°C. An RS-485 transceiver is an interface IC that converts logic-level signals into differential bus signals and converts received differential signals back into logic levels. RS-485 belongs to the differential data-interface hierarchy, where the voltage between the A and Y conductors carries the signal while common-mode noise is rejected. The SN65HVD77D is designed for robust, point-to-point, multidrop, and full-duplex industrial communication links. The primary feature of the SN65HVD77D is its 50 Mbps signaling capability, making it suitable for high-speed data acquisition, factory automation, industrial control, and communications equipment. Its ±12 kV IEC-rated ESD protection improves system resilience when cables connect the transceiver to external equipment. Operating from a 3.3 V rail also simplifies integration with 3.3 V controllers, FPGAs, DSPs, and other digital logic. Each device contains separate driver and receiver inputs and outputs, eliminating the shared bus direction controls commonly found on half-duplex transceivers. Full-duplex operation allows data to be transmitted and received at the same time. The transmitter drives a differential pair, while the receiver provides a complementary logic-level output. Because there are no external enable controls, the device is intended for continuous enabled operation rather than controlled low-power bus shutdown. Typical implementations connect the logic-side data pins to a communications controller, connect the A and Y pins to a protected twisted-pair bus, and place the receiver output in the controller's receive path. Full-duplex systems use separate differential pairs for transmission and reception. The SOIC-8 package supports conventional surface-mount assembly and is suitable for industrial control boards, test equipment, motor-control systems, and embedded communications modules. The principal design consideration is signal integrity. High-speed differential routing requires controlled impedance, a continuous return path, minimized stubs, and proper termination at the bus endpoints. External protection may still be required for severe industrial transients because the integrated ESD rating addresses electrostatic discharge rather than every surge or lightning event. This product page combines the manufacturer's principal electrical and environmental specifications with same-package transceiver options, application guidance, and practical PCB-layout considerations. These engineering details help simplify device selection, footprint verification, and robust RS-485 implementation.

Devis Contact
SN65HVD96D - 5 Mbps SymPol Transceiver | Texas Instruments
SN65HVD96D

SN65HVD96D - 5 Mbps SymPol Transceiver | Texas Instruments

The Texas Instruments SN65HVD96D is a half-duplex, 1/1 SymPol transceiver operating from a single 5 V supply in an 8-pin SOIC package. It supports signaling up to 5 Mbps, communicates reliably on normal or reversed-wire bus lines, and uses a symmetric-polarity receiver with 100 mV hysteresis. These characteristics make it suitable for industrial point-to-point, multi-drop, and multi-point communication networks. A SymPol transceiver is a physically robust bus interface integrated circuit that combines a differential driver and differential receiver into one package. It belongs to the interface IC hierarchy, alongside RS-485 transceivers, but uses symmetric polarity rather than the conventional RS-485 differential signaling convention. The SN65HVD96 series is an upgrade path for RS-485 installations, although the devices are not protocol-compatible with existing RS-485 networks. Key electrical features include a 4.75 V to 5.25 V supply range, one transmitter and one receiver, 5 Mbps signaling, 100 mV receiver hysteresis, and support for reversed-wire connections. The symmetric-polarity receiver helps the device interpret bus states consistently when conductors are connected in reverse. The 8-pin SOIC package also saves board area compared with equivalent discrete driver and receiver implementations. TI specifies an industrial operating range from -40 °C to 85 °C, making the device suitable for industrial instrumentation, factory automation, and commercial equipment that operates outside extended automotive temperature limits. The SOIC outline supports conventional surface-mount assembly, while the eight-pin footprint reduces the number of components needed to implement a robust bus node. Typical uses include industrial sensor networks, process-control equipment, remote monitoring stations, PLC peripheral interfaces, and point-to-point data links between controllers and field devices. Because the SN65HVD96D supports reversed wiring and 5 Mbps signaling, it is particularly useful where field installation errors or shorter, higher-speed interconnects are expected. The device pinout is identical to the industry-standard SN75176 transceiver, allowing an SN75176-based board to be considered for a SymPol migration. Existing RS-485 firmware and system behavior are not automatically compatible because SymPol is not backward compatible with RS-485, so the bus protocol and termination strategy must be reviewed before replacement. This page consolidates verified manufacturer and distributor information, package and pinout details, application guidance, and migration considerations that are not presented together on a standard distributor listing. Pricing and drop-in replacement availability are reported only where supported by verified source data.

Devis Contact
SN65LBC176DR - 10Mbps RS-485 Transceiver 5V | Texas Instruments
SN65LBC176DR

SN65LBC176DR - 10Mbps RS-485 Transceiver 5V | Texas Instruments

The Texas Instruments SN65LBC176DR is a differential bus transceiver combining a 3-state differential line driver and a differential input line receiver, both operating from a single 5V supply, in an 8-pin SOIC (D) package rated from -40C to +85C. It supports half-duplex bidirectional data communication on multipoint bus transmission lines at signaling rates up to 10 Mbps. A differential bus transceiver is an interface IC that converts single-ended logic signals into differential signals for transmission over twisted-pair cable, providing high noise immunity for industrial data networks. The SN65LBC176 belongs to the RS-485/RS-422 transceiver family within the broader hierarchy of interface ICs and line drivers, and it meets or exceeds the requirements of ANSI TIA/EIA-485 (RS-485) and ISO 8482:1987 (E). Key features include a driver enable (DE, active-high) and receiver enable (RE, active-low) that can be tied together to form a single direction-control pin, low-skew LinBiCMOS technology designed for high-speed serial and parallel data transmission, and bus fault protection across a -10V to +15V common-mode range. The driver outputs differential signals on pins A and B while the receiver accepts differential input, allowing direct connection to the multipoint bus. One driver and one receiver per device simplify point-to-point and multidrop network nodes. The LinBiCMOS process yields low power consumption with high output drive, supporting bus loading of up to 32 unit loads and cable lengths of several thousand feet at lower data rates. Typical applications include industrial automation networks, motor-drive communication links, building automation, energy metering, and any half-duplex RS-485 fieldbus requiring 10 Mbps throughput. Design tip: bias the bus with fail-safe resistor dividers (typically 560 ohm to the A-line pull-down and B-line pull-up) and terminate both bus ends with 120 ohm to prevent reflections and ensure a defined receiver state when all drivers are disabled.

USD $1,27 Contact
SN65LVDS105PWR - 1:4 LVDS Clock Fanout Buffer 400Mbps | TI
SN65LVDS105PWR

SN65LVDS105PWR - 1:4 LVDS Clock Fanout Buffer 400Mbps | TI

The Texas Instruments SN65LVDS105PWR is a 1 LVTTL-to-4 LVDS clock fanout buffer and repeater that accepts a single low-voltage TTL input and drives four differential LVDS output pairs at data signaling rates up to 400 Mbps (clock frequencies to 400 MHz), operating from a single 3.3-V supply (3 V to 3.6 V) in a 16-pin TSSOP (PW) package. A clock fanout buffer is a timing distribution device that takes one reference clock or data stream and replicates it across multiple identical outputs, maintaining signal integrity over transmission lines. Within the system hierarchy, it belongs to the clock buffer and signal repeater family of interface ICs, sitting between the clock source and the differential receivers distributed across a backplane or board. LVDS, as specified in ANSI EIA/TIA-644, is a low-voltage differential signaling technique offering low power, low noise coupling, and high switching speeds over relatively long distances. Key features include four differential LVDS line drivers meeting or exceeding the ANSI EIA/TIA-644 LVDS standard, a typical output voltage swing of 350 mV into a 100-ohm load, operation from a single 3.3-V rail, and support for signaling rates to 400 Mbps. The LVTTL-compatible input allows direct connection to standard CMOS or TTL clock sources without external level translation. Technically, the SN65LVDS105 integrates one LVTTL receiver stage followed by four parallel LVDS drivers implemented with current-mode outputs, which limit the slew-related EMI and crosstalk compared with single-ended signaling. The small 350-mV differential swing over a 100-ohm terminated line reduces power consumption relative to PECL while sustaining high data rates, making the part well suited to dense timing trees. Typical applications include clock distribution to backplane line cards, LVDS signal retiming and repeat in telecom and networking equipment, and fanout of a processor or FPGA reference clock to multiple serializer or ADC loads. Design consideration: route each LVDS output pair as a controlled-impedance 100-ohm differential pair, and keep the LVTTL input trace away from the LVDS pairs; on multilayer boards TI recommends at least two separate signal planes to reduce TTL/CMOS-to-LVDS crosstalk. This page synthesizes distributor pricing, verified drop-in alternatives, application guidance, and design notes not found in the manufacturer datasheet alone.

Devis Contact
SN65LVDS105PWRG4 - 1:4 LVDS Clock Fanout Buffer 400Mbps | TI
SN65LVDS105PWRG4

SN65LVDS105PWRG4 - 1:4 LVDS Clock Fanout Buffer 400Mbps | TI

The Texas Instruments SN65LVDS105PWRG4 is a 1 LVTTL-to-4 LVDS clock fanout buffer and repeater that supports data signaling rates up to 400 Mbps, operates from a single 3 V to 3.6 V supply, and is housed in a 16-pin TSSOP (PW) package. It accepts one low-voltage TTL (LVTTL) input and drives four differential LVDS output pairs that meet or exceed the ANSI EIA/TIA-644 LVDS standard. A clock fanout buffer is a timing-distribution component in the clock and timing hierarchy of a digital system. It takes a single reference clock (or data stream) and replicates it to multiple loads while preserving signal integrity, edge rate, and jitter performance. In LVDS-based systems, the fanout buffer also converts single-ended LVTTL levels to low-voltage differential signaling, which offers common-mode noise immunity and lower electromagnetic emissions than single-ended CMOS or TTL clock distribution. Key features of the SN65LVDS105 include compliance with the ANSI EIA/TIA-644 LVDS electrical standard, typical LVDS output swing of approximately 285 mV into a 100-ohm load, and bus-terminal ESD tolerance that exceeds 12 kV (per TI family datasheet information for this device class). The four LVDS drivers provide deterministic propagation delay with a typical buffer delay of 2.2 ns, enabling predictable multi-load clock skew planning. The device operates from a 3.3 V nominal supply (3 V to 3.6 V range), making it compatible with standard logic rails. The LVTTL receiver input accepts standard 3.3 V logic levels, so the part can sit directly between an FPGA, MCU, or clock generator output and four separate LVDS destinations such as displays, serializers, or data converters. The SN65LVDS104 companion variant accepts differential input levels (+/-100 mV typical) instead of LVTTL, allowing true LVDS repeater designs. Typical applications include backplane clock distribution, point-to-point LVDS data links, LCD panel timing distribution, telecom and networking line cards, and industrial control systems requiring 400 Mbps-class differential signaling over controlled-impedance traces. Design consideration: use 100-ohm differential termination at each LVDS receiver, keep the four output pairs tightly length-matched, and verify supply decoupling with 0.1 uF ceramic capacitors at each VCC pin to minimize jitter contribution. This page synthesizes distributor listings, cross-reference data, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
SN65LVDS31D - 400 Mbps Quad LVDS Driver | Texas Instruments
SN65LVDS31D

SN65LVDS31D - 400 Mbps Quad LVDS Driver | Texas Instruments

The Texas Instruments SN65LVDS31D is a 400-Mbps low-voltage differential signaling (LVDS) quad high-speed differential driver with four independent driver outputs, a 3.3 V supply, and a 16-pin SOIC package. According to the manufacturer product data, it meets or exceeds ANSI TIA/EIA-644 requirements and provides a typical differential output voltage of 350 mV into a 100-ohm load. An LVDS differential line driver is a high-speed interface IC that converts CMOS or LVTTL inputs into low-voltage differential outputs. In the broader hierarchy, an LVDS driver belongs to differential line-driver ICs, interface ICs, and semiconductors. Its differential signaling reduces common-mode noise sensitivity and supports reliable point-to-point data transmission over balanced interconnects. Key features include four drivers in one package, operation from a 3.3 V supply, 400-Mbps signaling capability, typical 1.7 ns propagation delay, and typical output rise and fall times of 500 ps. The manufacturer product page also identifies pin compatibility with AM26LS31, MC3487, and µA9638, enabling board-level substitution where electrical and timing requirements are confirmed. The SN65LVDS31D is intended for high-speed point-to-point links, including display and video backplanes, industrial control links, communications equipment, and test systems. Differential outputs help maintain signal integrity when the source and destination are connected through controlled-impedance traces or a suitable cable. When designing around this device, use the manufacturer’s recommended termination and layout practices. Confirm trace impedance, keep the differential pair routed with matched geometry, provide adequate bypassing near the supply pins, and verify receiver, cable, and connector characteristics. The supplied data confirms -40°C to +85°C operation for the SOIC-16 device, while other electrical limits should be taken directly from the manufacturer datasheet. This page combines the verified manufacturer identification, distributor listing, pricing reference, interface context, and engineering-focused application guidance. It is intended to help engineers identify the correct part, validate compatibility, and plan a robust LVDS interconnect without treating unsupported parameters as guaranteed specifications.

Devis Contact
SN65LVDS32D - 400 Mbps Quad LVDS Receiver | Texas Instruments
SN65LVDS32D

SN65LVDS32D - 400 Mbps Quad LVDS Receiver | Texas Instruments

Texas Instruments SN65LVDS32D is a 400 Mbps quad high-speed differential receiver designed for low-voltage differential signaling (LVDS), supplied from a single 3.3 V supply and housed in a 16-pin SOIC package. It provides four differential receiver channels, differential input thresholds of 100 mV maximum, typical propagation delay of 2.1 ns, and typical power dissipation of 60 mW. The receiver is intended for systems requiring reliable high-speed differential input reception under industrial and automotive-qualified conditions. An LVDS receiver is an interface circuit that converts a small differential voltage across a balanced pair into a digital logic signal. It belongs to the receiver and transceiver interface IC category, within broader communication-interface and signal-conditioning electronics. Differential reception rejects common-mode noise and helps maintain signal integrity across longer interconnects or cables than ordinary single-ended logic receivers. The SN65LVDS32D implements the electrical characteristics associated with ANSI TIA/EIA-644, as identified in the manufacturer product data. Key features include four independent receiver channels, operation from one 3.3 V supply, signaling rates up to 400 Mbps, 100 mV maximum differential input threshold, and open-circuit fail-safe behavior suitable for cold-sparing and redundant systems. The manufacturer product page also identifies pin compatibility with AM26LS32, MC3486, and µA9637. Automotive qualification and ESD protection features make the device relevant to industrial control, communications, test equipment, and vehicle electronics where differential signaling is required. The electrical performance is centered on low-latency differential reception. A typical 2.1 ns propagation delay is useful when the system must preserve timing relationships across multiple channels. The 60 mW typical power dissipation provides a practical baseline for power budgeting, although actual dissipation depends on supply voltage, input activity, output loading, and operating temperature. The single-supply architecture simplifies system power design while requiring correct input common-mode and termination practices. Typical applications include industrial automation links, high-speed data acquisition, point-to-point communications, test and measurement equipment, and automotive or other harsh-environment interfaces. In these systems, the receiver is placed after a balanced transmission line and connected to downstream digital logic through its four differential receiver outputs. Designers should verify the complete channel budget, cable or PCB loss, termination, grounding, and input common-mode range in the system-level design. A key design consideration is preserving the LVDS signal path: use controlled-impedance routing, matched differential pair geometry, appropriate termination, and short return paths to avoid degrading the 400 Mbps target. Do not treat the receiver as a general-purpose comparator or add logic without checking the output timing, supply requirements, and pin-specific electrical limits. This page combines the verified manufacturer and distributor information with practical LVDS design guidance for component selection and implementation.

Devis Contact