Produits (46 000+)

SN65LVDS93ADGGR - LVDS Serializer 10-135MHz 56-TSSOP | TI
SN65LVDS93ADGGR

SN65LVDS93ADGGR - LVDS Serializer 10-135MHz 56-TSSOP | TI

The Texas Instruments SN65LVDS93ADGGR is a FlatLink LVDS serializer (SerDes transmitter) that converts 28 bits of single-ended LVTTL parallel data into 4 LVDS data pairs plus 1 LVDS clock pair, operating over a 10 MHz to 135 MHz input clock range in a 56-pin TSSOP (DGG) package rated from -40C to +85C. An LVDS (Low-Voltage Differential Signaling) serializer is an interface IC that compresses a wide parallel data bus onto a small number of high-speed differential pairs, dramatically reducing connector size, cable count, and EMI between a host processor and a display or backplane. Within the signal-chain hierarchy, it belongs to the SerDes (serializer/deserializer) family of high-speed interface products, sitting between parallel LVTTL logic and LVDS physical-layer line drivers. Key features of the SN65LVDS93A include 28:4 data channel compression delivering up to 1.904 Gbps serialized throughput per the datasheet, an integrated 7x clock synthesizer that multiplies the input reference clock, and five LVDS line drivers meeting the TIA/EIA-644 LVDS standard for low EMI differential signaling. The A-suffix version extends the supported operating range to 10 MHz - 135 MHz, making it faster than the base SN65LVDS93, which is specified from 20 MHz to 68 MHz on TI.com. Architecturally, the device contains four 7-bit parallel-load serial-out shift registers, the 7x PLL clock synthesizer, and five LVDS drivers in a single IC. Data is latched on the parallel clock, shifted out at 7x rate, and transmitted with the embedded clock pair so a matching deserializer such as the SN65LVDS96 or DS90CF384 can recover timing without a separate clock channel. LVDS current-mode drivers on a 3.3V supply produce approximately 350 mV differential swings with low skew. Typical applications include TFT-LCD panel interfacing in industrial displays and medical monitors, video transmission between a graphics controller and a FlatLink-compatible display, and point-to-point board-to-board links where a 28-bit parallel bus must cross a flex cable or backplane with minimal wiring. When designing with this device, keep the parallel input setup/hold times within datasheet limits and route the LVDS pairs as controlled-impedance 100-ohm differential traces; also confirm the exact input clock range against your system, since TI lists both a 10-135 MHz range (A version) and 20-68 MHz (base part) across product pages. This page synthesizes distributor inventory data, drop-in alternatives, pinout guidance, and practical design notes not found in the manufacturer datasheet alone, with pricing refreshed as of 2026-10-19.

Devis Contact
SN65LVDT100DGK - 2Gbps LVDS Repeater/Translator | Texas Instruments
SN65LVDT100DGK

SN65LVDT100DGK - 2Gbps LVDS Repeater/Translator | Texas Instruments

The Texas Instruments SN65LVDT100DGK is a 2-Gbps LVDS, LVPECL and CML to LVDS repeater/translator in an 8-pin VSSOP (DGK) package. It accepts low-voltage differential signaling (LVDS), positive-emitter-coupled logic (PECL), or current-mode logic (CML) input signals at signaling rates up to 2 Gbps and regenerates them as clean LVDS output levels, operating from a single 3 V to 3.6 V supply. A differential repeater/translator is an interface IC that sits in a high-speed serial signal path, receiving a degraded or logic-incompatible differential signal and re-driving it with fresh, standard-compliant output levels. Within the signal-chain hierarchy, it belongs to the buffer/repeater family of interface ICs, bridging logic families (LVDS, LVPECL, CML) that would otherwise require discrete level-shifting networks and termination circuitry. Key features include a maximum total jitter of 100 ps, low part-to-part skew, and receiver input threshold hysteresis of tens of millivolts for noise immunity on marginal input signals. A distinctive advantage is the integrated 110-ohm differential line termination resistor, which shortens stub length, reduces component count, and saves board space compared with discrete 100-ohm termination schemes. TI positions this device as a low-power alternative to the MC100EP16 ECL repeater. Architecturally, the receiver front-end accepts a wide-range differential input (LVDS, PECL, or CML swings) and drives a current-mode LVDS output stage designed for 100-ohm differential transmission lines. The short signal path through the device (analog repeat, no FIFO or retiming logic) keeps propagation delay low, and TI's Bipolar/high-speed process supports multi-gigabit signaling while remaining within a modest supply-current budget at 3.3 V. Typical applications include backplane and point-to-point LVDS link conditioning, clock distribution and repeating in telecom and networking equipment, and extending LVDS display or camera links where cable losses degrade eye diagrams. Where a PECL output is required instead of LVDS, the companion SN65LVDS100/SN65LVDT101 family members cover that case in related packages. Design consideration: keep the input traces to the integrated termination as short as possible; the device must receive a differential signal that crosses its threshold window with hysteresis, so check eye margins at 2 Gbps with your actual channel loss before committing to layout. This page synthesizes distributor availability data, TI family cross-references, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet alone. Pricing shown is as of 2026-10-19 and is an estimate pending live distributor verification.

Devis Contact
SN65MLVD200ADR - Half-Duplex M-LVDS Transceiver, 8-SOIC | TI
SN65MLVD200ADR

SN65MLVD200ADR - Half-Duplex M-LVDS Transceiver, 8-SOIC | TI

The Texas Instruments SN65MLVD200ADR is a half-duplex Multipoint-LVDS (M-LVDS) transceiver in an 8-pin SOIC package, with one driver and one receiver sharing a single differential bus pair. It conforms to the M-LVDS standard (TIA/EIA-899) and supports data rates up to 100 Mbps (200 Mbps in some drive modes) with low 700 ps driver output skew, making it suitable for high-speed multipoint backplane and clock-distribution links. The IC operates from a single 3.3 V supply and provides 24 mA of drive current on the M-LVDS bus pins, with internal fail-safe biasing on the receiver inputs. Background: An LVDS (Low-Voltage Differential Signaling) transceiver is a type of high-speed differential interface IC that transmits data across a balanced pair of wires using low-swing, current-mode signaling, achieving high noise immunity at low power. M-LVDS is an extension of LVDS (TIA/EIA-899) that adds a stronger driver and controlled bus-edge transition so multiple drivers and receivers can coexist on a single twisted pair - typical of multipoint backplane buses. Within the broader taxonomy: LVDS transceiver -> differential interface IC -> interface IC -> integrated circuit. Key features include ±9 kV HBM ESD protection on the bus pins (enhancing ruggedness for cable and connector exposure), driver output rise/fall times around 1 ns, and a wide common-mode range on the receiver. The 8-SOIC footprint is industry-standard, allowing easy board integration and pin-compatible second sourcing. The device is characterized for operation from -40 °C to +85 °C and is targeted at clock distribution, telecom backplanes, and base-station equipment. Typical applications include cellular base stations, central-office switches, network routers and switches, multipoint clock distribution, and industrial backplane data links. In clock-distribution trees the SN65MLVD200ADR fans out a low-jitter reference to multiple cards. Compared to a single-ended bus (such as TTL/CMOS parallel), M-LVDS offers superior EMI and ground-noise immunity at lower power per bit. Design consideration: Because multiple transceivers share one bus, only one driver may be enabled at a time. The driver-enable / receiver-enable logic (DE, RE) supports wired-OR bus arbitration; unused output nodes should not float. Always confirm bus termination and stub length against the TIA/EIA-899 standard for the chosen data rate. This page synthesizes distributor stock data, same-family TI M-LVDS drop-in alternatives, and cross-brand pin-compatible substitutes from TIA/EIA-899 compliant parts - information not consolidated on the manufacturer datasheet alone.

Devis Contact
SN74ABT162841 - 20-Bit Bus-Interface D-Type Latch | TI
SN74ABT162841

SN74ABT162841 - 20-Bit Bus-Interface D-Type Latch | TI

The SN74ABT162841 is a 20-bit bus-interface D-type transparent latch with 3-state outputs, designed by Texas Instruments as part of the Widebus family. It features noninverting outputs and is optimized for driving highly capacitive or relatively low-impedance loads. The device operates from a 4.5V to 5.5V supply, with a typical propagation delay of 4.6 ns and output ground bounce below 0.8V at VCC = 5V and TA = 25°C. It is available in a 56-pin SSOP package (DL suffix) and a 56-pin TSSOP package (DLR suffix). A bus-interface D-type latch is a digital logic component that captures data on its D inputs when the latch enable (LE) signal is asserted, holding the data on its Q outputs until the next enable pulse. It is a fundamental building block in digital systems for temporary data storage, bus isolation, and signal synchronization. In the hierarchy of digital logic, it belongs to the category of latches, which are level-sensitive storage elements, as opposed to edge-triggered flip-flops. Latches are essential in microprocessor systems, memory interfaces, and data acquisition circuits where multiple data lines must be captured simultaneously. Key features of the SN74ABT162841 include 3-state outputs that allow connection to a shared bus without contention, a flow-through architecture that simplifies PCB layout, and distributed VCC and GND pins that minimize high-speed switching noise. The device also supports hot insertion with Ioff and power-up 3-state, and its latch-up performance exceeds 500 mA per JEDEC standards. The EPIC-B BiCMOS design significantly reduces power dissipation compared to bipolar logic, making it suitable for high-density systems. Technically, the SN74ABT162841 uses a BiCMOS process that combines the speed of bipolar transistors with the low power of CMOS. The outputs have equivalent 25-ohm series resistors, eliminating the need for external resistors in many applications. The device is characterized for operation from -40°C to 85°C, and it is RoHS compliant. The 3-state outputs are controlled by an output enable (OE) input, which places the outputs in a high-impedance state when asserted high, allowing multiple devices to share a bus. Typical applications include memory address latching, data bus buffering in microprocessor systems, and interface circuits for industrial control and telecommunications equipment. The wide operating voltage range and high drive capability make it ideal for 5V systems that require robust signal integrity. The flow-through pinout aligns inputs and outputs on opposite sides, simplifying board routing and reducing crosstalk. When designing with this device, ensure that the OE and LE inputs are properly driven to avoid bus contention. The 3-state outputs allow multiple latches to share a bus, but only one should be enabled at a time. Consider the propagation delay and setup/hold times when designing timing margins for high-speed applications.

Devis Contact
SN74ABT244APWR - Octal Buffer/Driver 3-State TSSOP-20 | TI
SN74ABT244APWR

SN74ABT244APWR - Octal Buffer/Driver 3-State TSSOP-20 | TI

The Texas Instruments SN74ABT244APWR is an octal non-inverting buffer/driver with 3-state outputs, operating from a 4.5V to 5.5V supply, delivering +/-32 mA drive capability per output in a 20-pin TSSOP (PW) package rated from -40C to +85C. It is built on TI's state-of-the-art EPIC-B BiCMOS process. An octal buffer is a logic IC containing eight buffer gates in one package, used to increase current drive, isolate capacitive loads, and provide 3-state control on bus-oriented systems. Buffers belong to the broader logic IC hierarchy: gate -> buffer/driver -> bus interface -> standard logic family. The 74ABT family is an advanced BiCMOS variant of the classic 74244 topology, combining the speed and drive of bipolar transistors with the low static power of CMOS. Key features include TTL-compatible CMOS inputs for direct interfacing with 5V TTL logic, individual active-low output-enable pins (/OE1 and /OE2) for independent control of two 4-bit sections, and 3-state outputs that present a high-impedance state for shared-bus applications. The device significantly reduces power dissipation compared with bipolar-only predecessors. Technical strengths of the ABT family include latch-up performance exceeding 500 mA per JEDEC JESD-17 and ESD protection exceeding 2000 V per MIL-STD-883 Method 3015 (and exceeding 200 V on the machine model), according to the manufacturer datasheet. The BiCMOS output stage provides high transient drive into heavy bus capacitance, preserving edge rates on backplanes and ribbon interconnect. Typical applications include 5V microprocessor and microcontroller bus buffering, memory address/data line drivers, backplane and ISA-style industrial bus interfaces, and I/O isolation between subsystems with high fan-out requirements. The dual 4-bit structure lets one device buffer two independent buses or a bidirectional bus when paired with direction control. Design tip: tie unused /OE inputs HIGH through a pull-up resistor so outputs default to high-impedance during power-up, preventing bus contention; keep the VCC-GND pairs well decoupled with 0.1 uF ceramic capacitors because the ±32 mA transient currents create ground bounce. This page synthesizes distributor pricing, verified drop-in alternatives, pinout detail, and practical design notes not consolidated in the manufacturer datasheet, providing information gain for sourcing and engineering teams evaluating 5V octal bus drivers.

Devis Contact
SN74ABT244APWRE4 - Octal 3-State Buffer 5V TSSOP-20 | TI
SN74ABT244APWRE4

SN74ABT244APWRE4 - Octal 3-State Buffer 5V TSSOP-20 | TI

The Texas Instruments SN74ABT244APWRE4 is an octal non-inverting buffer/driver with 3-state outputs, operating from a 4.5 V to 5.5 V supply in a 20-pin TSSOP (PW) surface-mount package. It is organized as two 4-bit buffer elements with independent output-enable (OE) controls, delivering TTL-compatible drive for heavily loaded 5V buses. A buffer and line driver is a digital logic device that provides signal amplification, fan-out expansion, and isolation between a low-drive controller and high-capacitance loads. Within the logic hierarchy, line drivers sit between simple gates and full bus transceivers, providing unidirectional buffering with output enable control for bus-oriented systems. The 244 configuration is the industry-standard octal non-inverting buffer pinout. Key features include Advanced BiCMOS (ABT) EPIC-II process technology that significantly reduces power dissipation compared to earlier bipolar families, 3-state outputs that allow direct connection to shared bus lines, and separate active-low OE1 and OE2 pins controlling the two 4-bit halves independently. Outputs are rated for high capacitive drive, making the part ideal for memory address driving and clock distribution. According to TI, the family targets 3-state memory address drivers, clock drivers, and bus-oriented receivers and transmitters. The ABT architecture combines CMOS input logic with bipolar output transistors, giving the device TTL-compatible CMOS inputs, fast propagation delays, and robust output current capability at 5V operation. The PW package offers a compact 6.4 mm body with 0.65 mm pin pitch for space-constrained boards. Typical applications include 5V microprocessor bus buffering, memory address and data line driving, industrial I/O module isolation, and backplane driver stages in legacy 5V systems. For design, tie unused OE inputs to VCC through a pull-up to keep outputs in the high-impedance state during power-up, and decouple VCC with 0.1 uF ceramics. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet alone.

Devis Contact
SN74ABT244APWRG4 - Octal 3-State Buffer 5V TSSOP-20 | TI
SN74ABT244APWRG4

SN74ABT244APWRG4 - Octal 3-State Buffer 5V TSSOP-20 | TI

The Texas Instruments SN74ABT244APWRG4 is an octal non-inverting buffer/line driver with 3-state outputs, operating from a 4.5V to 5.5V supply with a typical propagation delay of 4.6 ns, housed in a 20-pin TSSOP (PW) package rated from -40C to +85C. A line driver or buffer is a logic device that strengthens digital signals for transmission across buses, long PCB traces, or cables where fan-out, capacitive loading, or noise would otherwise corrupt data. Buffers sit within the broader logic IC hierarchy: gate -> buffer/driver -> bus transceiver -> logic IC. The 244 family is the industry-standard octal buffer topology, splitting its eight channels into two independently enabled 4-bit groups so one device can serve two separate buses or provide bidirectional-by-direction-control buffering. Key features of the SN74ABT244A include TTL-compatible CMOS inputs, 3-state outputs that tri-state for bus sharing, and a drive capability suited to heavily loaded backplanes. The device belongs to TI's BiCMOS ABT (Advanced BiCMOS Technology) family, which combines the low static power of CMOS with the high drive current and speed of bipolar output stages, significantly reducing power dissipation compared with older bipolar-only drivers. Technically, the ABT family uses TI's EPIC-BiCMOS process, providing output current levels capable of driving 50 pF loads while keeping propagation delays in the nanosecond range, and includes livable latch-up immunity and partially powered operation behavior typical of ABT parts (driving outputs while VCC is absent is a classic ABT benefit for hot-insertion-style designs). Typical applications include microprocessor and DSP address/data bus buffering, memory interface isolation, backplane driving in industrial control systems, and general 5V TTL logic level strengthening in instrumentation. Design consideration: always decouple VCC with a 0.1uF ceramic capacitor close to pin 20, and use the two /OE pins to guarantee 3-state condition during power sequencing or bus arbitration. This page adds value beyond the TI datasheet by synthesizing drop-in alternatives, pricing tiers, comparison tables, and practical design notes in one place.

Devis Contact
SN74AC240N - 8-Channel 3-State Inverter | Texas Instruments
SN74AC240N

SN74AC240N - 8-Channel 3-State Inverter | Texas Instruments

Texas Instruments SN74AC240N is an eight-channel CMOS octal buffer and line driver with inverting, three-state outputs, a 2 V to 6 V supply range, and a 20-pin PDIP package. The device is organized as two four-channel groups with separate output-enable controls, allowing eight bus outputs to be driven, disabled, or placed in a high-impedance state without changing the logic polarity of the incoming signals. An octal buffer/line driver is a logic IC used to increase drive strength and isolate a data bus from the load presented by downstream inputs. A three-state output can actively drive a logic level, remain at high impedance, or be placed in the high-impedance state by its output-enable input. This family belongs to the CMOS logic hierarchy, where AC-series devices operate from a 2 V to 6 V supply and are designed for low-voltage digital systems requiring buffered bus signals. The SN74AC240N provides eight inverting channels and separate controls for two four-channel output groups. Its principal features are the 2 V to 6 V operating range, eight channels, three-state output capability, and separate output enables. These characteristics make it useful when a system needs controlled bus isolation, increased source current for lightly loaded interconnects, or a defined way to disconnect portions of a bidirectional bus during a shared-bus architecture. Each output section combines an input buffer with an output driver capable of assuming a high-impedance state when its associated output-enable input is inactive. The two four-channel groups can be enabled independently, which supports segmented bus control. Because the outputs are inverting, system logic must account for reversed polarity at every driven signal. A three-state output does not actively hold the bus at a valid level while disabled; the receiving system must provide suitable pull-up or pull-down behavior when another device can drive that net. Typical uses include memory address buffering, clock distribution, bus-oriented receivers and transmitters, control-signal isolation, and industrial digital interfaces. The part is also suitable when several compatible devices share a common data path and only selected groups should drive it at a given time. Independent output-enable control simplifies arbitration, test access, and expansion of a shared bus. PCB design should keep the 20-pin PDIP footprint free of unintended shorts and route high-speed or noise-sensitive nets away from supply and return-current paths. Input and output-enable signals should have defined levels at every operating state, including power-up. Designers should also verify that all devices connected to a shared bus have compatible voltage levels and that their output-enable controls cannot overlap in an unintended drive condition. This product overview combines the device function, package, supply range, and bus-driver use cases with practical guidance for output-state control, polarity, and shared-bus implementation. It also organizes drop-in replacement information and engineering-oriented comparisons to support component selection before PCB release.

Devis Contact
SN74AC241N - 8-Channel 3-State Buffer | Texas Instruments
SN74AC241N

SN74AC241N - 8-Channel 3-State Buffer | Texas Instruments

Texas Instruments SN74AC241N is an eight-channel, non-inverting CMOS buffer with independently controlled 3-state outputs, a 2 V to 6 V operating supply range, and a 20-pin PDIP package. The device is organized as two 4-bit buffer elements and is intended for bus-oriented receivers, transmitters, memory-address drivers, and clock-driver applications. According to the TI product page, the SN74AC241 family supports a -40 °C to 85 °C operating-temperature range for the N package. A logic buffer is a digital semiconductor that reproduces an input signal at an output while providing buffering between a source and the next circuit stage. The 74AC family belongs to the advanced CMOS logic hierarchy, combining low-power operation with balanced drive capability and relatively high input impedance. In the SN74AC241, the tri-state output function allows each group of four outputs to be placed in a high-impedance state, preventing a disabled driver from actively driving a shared bus. The principal feature is independent output-enable control, allowing two 4-bit sections to be enabled or disabled separately. The non-inverting architecture preserves input logic polarity. Operation from 2 V to 6 V supports both 3.3 V and 5 V systems, while the maximum input voltage of 6 V provides tolerance for supply-transient conditions. The exact propagation-delay, output-current, input-current, and static-power values are not stated in the retrieved product information and must be confirmed in the manufacturer datasheet before timing, fanout, or signal-integrity calculations. SN74AC241N is a bus-oriented octal buffer rather than a general-purpose open-collector transceiver. Unlike a bidirectional transceiver, its data paths are unidirectional, and unlike a conventional non-3-state buffer, each four-output bank can be disabled. This makes the device appropriate when a controller, memory interface, or peripheral must be isolated from a shared bus while preserving standard logic levels. The N suffix identifies the through-hole PDIP package; board layout, insertion, and rework requirements therefore differ from surface-mount alternatives. Typical uses include address-line buffering between a memory controller and external memory, clock distribution into bus loads, isolation of peripherals from shared data buses, and buffering of control signals in modular industrial equipment. Because the device supports 3-state outputs, firmware or external logic can determine which bank drives a shared bus. Designers should still verify timing against the worst-case load and trace capacitance shown in the manufacturer datasheet rather than assuming performance from the family name alone. Decoupling and signal-integrity practice remain important in high-speed systems. Place the supply bypass capacitor close to the device, provide a continuous return path for output-current transients, and keep enable traces away from sensitive analog paths. Do not enable a bank while two outputs contend on the same bus unless the downstream system explicitly supports bus contention. Confirm that the selected source and destination devices meet the AC family voltage, temperature, and timing limits before using the buffer as an interface between unrelated logic families. This product page combines the manufacturer ordering information with practical bus-isolation guidance, verified package details, and a parameter-by-parameter replacement comparison. It also highlights the distinctions that matter during PCB design: the PDIP-20 footprint, independent 3-state enable control, unidirectional non-inverting operation, and the need to validate exact timing and drive-current limits against the selected system load.

Devis Contact
SN74AC244N - 8-Channel 3-State Buffer | Texas Instruments
SN74AC244N

SN74AC244N - 8-Channel 3-State Buffer | Texas Instruments

Texas Instruments SN74AC244N is an eight-channel, non-inverting buffer and line driver with 3-state outputs, a 2 V to 6 V supply range, and a 20-pin PDIP package. It is designed to increase the performance and density of three-state memory-address drivers, clock drivers, and bus-oriented receivers and transmitters. The device provides eight independently buffered data paths organized into two four-bit groups, with output-enable control for placing the outputs in a high-impedance state. A logic buffer or line driver is a digital integrated circuit that reproduces an input signal at an output while adding drive strength, isolation, or bus-management capability. The SN74AC244 belongs to the CMOS logic family and sits within the broader hierarchy of logic ICs, bus-interface ICs, and semiconductor components. Its three-state outputs allow multiple devices to share a data bus when their outputs are disabled, while the non-inverting architecture preserves the polarity of the input data. Key features include eight buffered channels, a 2 V to 6 V operating supply range, and operation from -40 °C to 85 °C in the N-package ordering option. Each output can be placed in a high-impedance state through the device's output-enable controls, making it suitable for shared buses where multiple transmitters must not contend during inactive periods. The 20-pin PDIP package supports through-hole assembly and is available in tube packaging. The SN74AC244 architecture separates eight input-to-output buffer channels from the bus-control logic. This arrangement supports propagation of address, control, and clock signals while providing stronger output drive than direct logic outputs. The high-impedance output state is particularly important when several buffer devices connect to the same bus; only the enabled device actively drives the shared conductors. Exact propagation-delay, output-current, and noise specifications should be selected from the manufacturer datasheet for the complete AC family. Typical uses include three-state memory-address driver systems, clock-distribution networks, bidirectional or multi-source bus interface arrangements, and bus-oriented receiver and transmitter interfaces. The SN74AC244 can also serve as an output-isolation stage when a logic core must drive a shared peripheral bus without contending with another subsystem. Designers should verify the output-enable polarity and timing against the system control logic before integrating the device. A key design consideration is ensuring that all devices connected to a shared bus agree on which output-enable state is active. Check the direction of the enable inputs and their timing relative to data changes so the bus is never released while two outputs actively drive it. Account for the additional propagation delay introduced by the buffer when establishing setup and hold timing at the receiving device. This page organizes the manufacturer's operating limits, package information, verified drop-in alternatives, comparison data, and practical implementation guidance. It also highlights the distinction between the eight-channel buffered function, the three-state bus-management feature, and the 20-pin PDIP footprint that engineers must confirm before redesigning or replacing an existing assembly.

Devis Contact
SN74AC574DWR - Octal D-Type Edge-Triggered F-F, 3-State | TI
SN74AC574DWR

SN74AC574DWR - Octal D-Type Edge-Triggered F-F, 3-State | TI

The Texas Instruments SN74AC574DWR is an octal D-type edge-triggered flip-flop with 3-state outputs, housed in a 20-pin SOIC (DW) package with a body width of 0.295" (7.50 mm). It operates from a 2 V to 6 V VCC supply, is fabricated in TI's AC (Advanced CMOS) logic family, and is rated for -40C to +85C commercial operation. Each device contains eight D-type flip-flops sharing a single positive-edge-triggered clock input and an Output Enable (OE) input that places all outputs in a high-impedance state when asserted. What is a D-type edge-triggered flip-flop? A flip-flop is a bistable memory element that captures one bit of data. An edge-triggered D-type flip-flop latches its D input value on the rising edge of the clock and holds that value stable until the next rising edge. When implemented in octal form with shared clock and OE controls, these devices serve as synchronous storage registers commonly used to capture multi-bit parallel data arriving from a bus, sensor array, or processor port. The 3-state output stage allows multiple octal registers to share a common bus without contention, which is why this topology is pervasive in microprocessor and DSP glue logic. Key features of the SN74AC574 include a typical clock frequency rating that supports high-speed bus interfaces, 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads directly, and inputs that tolerate voltages up to 6 V maximum. These devices are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers - the canonical applications for an octal registered buffer. From an architecture standpoint, the SN74AC574 builds on TI's AC advanced CMOS process, which delivers balanced drive strength and lower power dissipation than legacy bipolar or HC families at comparable speeds. Compared with non-edge-triggered latches (such as the '573), edge-triggered '574 removes the critical setup/hold timing pitfalls of transparent latches and is preferred wherever a registered output is needed on a synchronous clock domain. Typical applications include microprocessor and microcontroller bus expansion (registering address or data lines), memory interface buffering (capturing data into FIFO or RAM arrays), I/O port expansion for industrial controllers, LED drive registers, and parallel ADC/DAC data capture. The wide 2 V to 6 V supply range also makes the part compatible with both 3.3 V and 5 V system rails. When designing with this device, designers should pay attention to the SOIC-20 land pattern, the required clock pulse width per the datasheet timing table, and the OE timing relative to clock edges to avoid bus contention during asynchronous resets. The 'DW' (SOIC-20) suffix supports standard reflow soldering and reel packaging for high-volume assembly. This page synthesizes distributor pricing, drop-in pin-compatible alternatives from Texas Instruments and ON Semiconductor, and practical design notes not aggregated in the manufacturer datasheet alone.

Devis Contact
SN74ACT373-EP - Octal D-Type Transparent Latch | Texas Instruments
SN74ACT373-EP

SN74ACT373-EP - Octal D-Type Transparent Latch | Texas Instruments

The SN74ACT373-EP is an Enhanced Product octal D-type transparent latch with 3-state outputs from Texas Instruments, designed for driving highly capacitive or relatively low-impedance loads. This 8-bit latch operates over a wide VCC range of 4.5V to 5.5V, with inputs that accept voltages up to 5.5V and are TTL-voltage compatible. The device features a buffered output-enable (OE) input that places the eight outputs in either a normal logic state or a high-impedance state, enabling bus-organized systems without the need for interface or pullup components. An octal D-type transparent latch is a digital logic component that captures the state of eight data inputs (1D-8D) when the latch-enable (LE) input is high, and holds that state when LE is low. The 3-state outputs allow multiple devices to share a common bus, as each output can be disabled (high-impedance) to avoid contention. This device is part of the ACT family, which combines advanced CMOS technology with TTL-compatible inputs, offering high speed and low power consumption. Key features include a maximum propagation delay (tpd) of 5V, 3-state outputs for bus driving, and compatibility with TTL voltage levels. The Enhanced Product designation indicates extended temperature range and reliability for demanding applications. The device is available in multiple package options, including SOIC, SSOP, TSSOP, and PDIP, providing design flexibility. Technically, the SN74ACT373-EP uses a CMOS process that provides balanced propagation delays and high noise immunity. The 3-state outputs are controlled by the OE input, which when low, enables the outputs; when high, places them in high-impedance state. This allows the latch to drive bus lines directly, reducing the need for external buffers. The device also features a latch-enable (LE) input that is level-sensitive, making it transparent when high and latched when low. Typical applications include address latching in microprocessor systems, data buffering in memory interfaces, and general-purpose I/O expansion. The high drive capability and 3-state outputs make it ideal for bus-oriented designs where multiple peripherals share a common data bus. The wide operating temperature range of -40°C to 125°C (Enhanced Product) ensures reliable operation in industrial and automotive environments. When designing with this device, ensure that the OE and LE inputs are properly driven to avoid bus contention. The high-impedance state should be used to prevent multiple outputs from driving the same bus simultaneously. Additionally, consider the propagation delay and setup/hold times to meet system timing requirements.

Devis Contact
SN74AHC08RGYR - Quad 2-Input AND Gate, 14-VQFN | Texas Instruments
SN74AHC08RGYR

SN74AHC08RGYR - Quad 2-Input AND Gate, 14-VQFN | Texas Instruments

The Texas Instruments SN74AHC08RGYR is a quadruple 2-input positive-AND gate from the AHC (Advanced High-speed CMOS) logic family, housed in a 14-pin VQFN (RGY) package with 3.5 mm x 3.5 mm body and an exposed thermal pad. It performs the Boolean function Y = A · B (positive logic) across four independent gates, supports a 2 V to 5.5 V VCC operating range, and delivers a typical propagation delay of 9 ns at 5 V, making it well-suited for high-speed glue logic. An AND gate is a fundamental combinational logic primitive that produces a logic-high output only when all of its inputs are logic-high; in CMOS families it is built from a pull-up PMOS network in series with a pull-down NMOS network. Within the broader hierarchy, the AND gate belongs to logic gates -> combinational logic -> standard logic ICs -> integrated circuits. The AHC family sits between the slower HC (CMOS) and the lower-power AUC family, optimized for balanced speed and low static power dissipation in mixed 3.3 V / 5 V systems. Key features include ±8 mA output drive at 5 V, low static power consumption with ICC typically below 20 µA, and 5 V-tolerant inputs that allow safe interfacing with 3.3 V logic rails. The device offers robust ESD protection exceeding 2000-V HBM (JESD22-A114), 200-V MM, and 1000-V CDM models, plus latch-up immunity exceeding 250 mA per JESD 17. Schmitt-trigger action at the inputs ensures clean switching on slowly rising signals. Typical applications include industrial control signal gating, bus interfacing, power-up sequencing logic, address decoding, and general-purpose glue logic in microcontroller-based designs. The wide 2 V to 5.5 V supply range and balanced speed/power profile make it ideal for portable battery-powered equipment as well as mains-powered industrial controllers. When designing with this part, place 0.1 µF decoupling capacitors close to the VCC pin and tie unused inputs to VCC or GND to avoid floating inputs and undefined output states per TI application-note guidance. The exposed thermal pad should be soldered to a copper pour for improved mechanical reliability and thermal performance.

Devis Contact
SN74AHC1G00DBVR - 2-5.5V Single 2-Input NAND Gate | Texas Instruments
SN74AHC1G00DBVR

SN74AHC1G00DBVR - 2-5.5V Single 2-Input NAND Gate | Texas Instruments

The SN74AHC1G00DBVR is a single 2-input positive-NAND gate from Texas Instruments, designed for 2-V to 5.5-V operation. It performs the Boolean function Y = A NAND B in positive logic and is housed in a 5-pin SOT-23 (DBV) surface-mount package, making it ideal for space-constrained designs requiring low power and high noise immunity. A NAND gate is a fundamental digital logic gate that outputs LOW only when all inputs are HIGH. It is a universal gate, meaning any other logic function (AND, OR, NOT, XOR) can be built from NAND gates alone. The SN74AHC1G00 belongs to the AHC (Advanced High-Speed CMOS) logic family, which balances speed and power for battery-powered and portable systems within the broader CMOS logic IC hierarchy. Key features include a wide 2-V to 5.5-V operating range, a maximum propagation delay of 6.5 ns at 5 V, and maximum quiescent supply current of only 10 uA. Schmitt-trigger action on all inputs provides hysteresis-based noise immunity, allowing slow input edges without false triggering and eliminating external conditioning components. The device delivers ±8 mA output drive at 5 V, compatible with standard CMOS and TTL logic levels. Fabricated in advanced CMOS technology, the SN74AHC1G00 combines high-speed switching with low static and dynamic power dissipation. Robustness features include latch-up performance exceeding 250 mA per JESD 17 and ESD protection exceeding 2000-V HBM, 200-V MM, and 1000-V CDM ratings per the TI datasheet. Typical applications include signal gating, logic inversion, clock gating, and interface buffering in consumer electronics, industrial control, and automotive subsystems. The small SOT-23-5 footprint suits wearables, IoT modules, and dense PCBs where board area is at a premium. Design tip: do not let input voltages exceed VCC, and decouple the VCC pin with a 0.1-uF ceramic capacitor for best noise performance. Pricing shown reflects distributor data as of 2026-08-29.

Devis Contact
SN74AHC1G08-Q1 - Automotive 2-Input AND Gate SC-70-5 | TI
SN74AHC1G08QDCKRQ1

SN74AHC1G08-Q1 - Automotive 2-Input AND Gate SC-70-5 | TI

The Texas Instruments SN74AHC1G08-Q1 is an automotive-qualified single 2-input positive-AND gate that performs the Boolean function Y = A AND B in positive logic. Operating from a 2V to 5.5V supply, the device delivers a maximum propagation delay of 9 ns at 5V and comes in a 5-pin SC-70 (DCK) surface-mount package. A single-gate logic IC integrates exactly one logic function - here an AND gate - in a tiny footprint, unlike traditional quad-gate devices such as the 74HC08. Single-gate devices sit within the broader CMOS logic IC family, under combinational logic, and are widely used for glue logic, signal gating, and enable generation in modern PCBs where board space is at a premium. Key features include the AHC family's balanced CMOS architecture for low static power consumption, a wide 2V to 5.5V operating range supporting both 3.3V and 5V systems, and latch-up performance exceeding 250 mA per JESD 17. ESD protection exceeds 2000-V Human-Body Model, 200-V Machine Model, and 1000-V Charged-Device Model per TI datasheet. The -Q1 suffix denotes AEC-Q100 qualification for automotive applications. The AHC technology provides TTL-compatible CMOS outputs with balanced drive and fast switching, while the unbuffered single-stage design keeps propagation delay tight and predictable across the operating range. Typical applications include automotive body electronics and cluster gating, industrial PLC I/O conditioning, and general-purpose enable/signal gating in mixed 3.3V/5V systems. Design tip: keep unused input pins tied to VCC or GND, and place a 0.1uF decoupling capacitor close to the VCC pin to ensure clean switching edges and minimize ground bounce in automotive noise environments.

USD $0,09 Contact
SN74AHC1G08DBV3 - 1-Ch 2-Input AND Gate, 2-5.5V | TI
SN74AHC1G08DBV3

SN74AHC1G08DBV3 - 1-Ch 2-Input AND Gate, 2-5.5V | TI

The Texas Instruments SN74AHC1G08DBV3 is a single-channel, 2-input positive-AND gate from the AHC (Advanced High-Speed CMOS) logic family, housed in a 5-pin SOT-23 (DBV) package. It operates from a 2 V to 5.5 V supply, supports propagation delay of 9 ns maximum at 5 V (per TI's product page), and provides ±8 mA output drive at 5 V for driving moderate loads. The device performs the Boolean function Y = A · B in positive logic, making it a fundamental building block for digital decision-making and signal gating. An AND gate is a basic combinational logic gate that produces a HIGH output only when all of its inputs are HIGH. Logic gates are the fundamental building blocks of digital integrated circuits, sitting at the lowest level of the digital design hierarchy: logic gate -> combinational logic -> sequential logic -> microcontroller / ASIC. The AHC family is a higher-speed, lower-power evolution of the classic HC (High-Speed CMOS) family, designed for low static power consumption while delivering faster switching than HC and lower switching noise than TTL. Key features include a wide 2 V to 5.5 V operating range, ±8 mA balanced output drive at 5 V, 10 µA maximum quiescent supply current (Icc), and a Schmitt-trigger action on the inputs that makes the device tolerant of slowly rising edges. The SOT-23-5 footprint (DBV) is one of the industry's smallest logic-gate packages, enabling high-density board layouts in space-constrained designs. The device is also characterized for operation over the -55 °C to +125 °C free-air temperature range, suitable for industrial and harsh-environment applications. Internally, the SN74AHC1G08 uses a standard CMOS push-pull output stage with a buffered input. The Schmitt-trigger input hysteresis typically exceeds 1 V at 5 V, which improves noise immunity in environments with slow or noisy input edges. The wide Vcc range allows the part to translate logic levels between 3.3 V and 5 V domains without external level shifters, useful when interfacing microcontrollers, sensors, and older 5 V peripherals. Typical applications include power-rail sequencing and control logic in portable and battery-powered devices, enabling logic and control in industrial sensor interfaces, level shifting between 3.3 V and 5 V rails, general-purpose glue logic in microcontroller-based embedded designs, and signal gating in test and measurement equipment. The wide supply range and small package make it a versatile companion to virtually any digital subsystem. When designing with this device, place a 0.1 µF decoupling capacitor as close as possible to the Vcc pin and minimize input trace lengths to avoid noise-induced glitches. Because this is a non-inverting AND function, be aware that it cannot be used as a NAND; if inverted output is required, cascade with an inverter such as SN74AHC1G04 in the same SOT-23-5 package. This page synthesizes distributor pricing, drop-in same-package alternatives, and design guidance not always present in the manufacturer datasheet, providing actionable engineering reference for selection, replacement, and layout.

Devis Contact
SN74AHC373PWR - Octal Transparent D-Type Latch | TI | 20-TSSOP
SN74AHC373PWR

SN74AHC373PWR - Octal Transparent D-Type Latch | TI | 20-TSSOP

The Texas Instruments SN74AHC373PWR is an octal transparent D-type latch with 3-state outputs, operating from 2V to 5.5V VCC, housed in a 20-pin TSSOP (PW) package. It provides eight D-type latches organized as a single 8:8 channel with non-inverting transparent latch behavior, controlled by a latch-enable (LE) input and an active-low output-enable (OE) bar input that places outputs in high-impedance state. A latch is a sequential storage element that captures data when the latch-enable is asserted and holds it transparently or in storage mode. As a member of the AHC (Advanced High-speed CMOS) family, this device is pin-compatible with the HC (High-speed CMOS) logic family while delivering lower static power and faster switching at 5V operation. The latches occupy a position in the logic hierarchy between simple flip-flops and bus-oriented register files, making them ideal for address/data bus demultiplexing, I/O port expansion, and state retention in microcontroller-based systems. Key features include a typical propagation delay of 8.5 ns at 5V, support for +/-8 mA output drive, and ESD protection exceeding JESD 22 (2000V human-body model, 200V machine model, 1000V charged-device model). The device offers low power consumption with a typical quiescent current of 4 uA, supports +/-50 mA bus-hold and bus-drive, and provides true 5V tolerant inputs on a 2V-5.5V supply rail. Internally, the SN74AHC373 uses eight transparent D latches each with a 3-state output buffer. When LE is HIGH, the latch is transparent and follows the D input; when LE falls LOW, the value is stored. The OE bar pin enables the output buffers; when OE bar is HIGH, outputs are high-impedance. This architecture is widely used as a simple 8-bit data register or address demultiplexer. Typical applications include LED driving via 8-bit port expansion, address demultiplexing in microcontroller memory interfaces, bus isolation in mixed-voltage systems, and general-purpose 8-bit data storage. The wide 2V-5.5V range enables direct interfacing between 3.3V MCUs and 5V peripherals. When designing with this part, ensure that OE bar is properly tied to GND through a pull-down resistor if not actively driven, to prevent floating outputs. Unused D inputs should be tied to VCC or GND to avoid floating CMOS inputs. The TSSOP-20 package has a low thermal resistance suitable for industrial temperature operation. This page synthesizes distributor pricing, drop-in alternatives from same-brand and cross-brand vendors, and practical design notes not found in the manufacturer datasheet.

Devis Contact
SN74AHC3G99-Q1 - Triple Configurable Logic Gate AEC-Q100 | TI
SN74AHC3G99-Q1

SN74AHC3G99-Q1 - Triple Configurable Logic Gate AEC-Q100 | TI

The Texas Instruments SN74AHC3G99-Q1 is an automotive-grade triple ultra-configurable multiple-function gate containing three independent configurable logic gates, each with four inputs and a 3-state output, implementing the Boolean function Y = (A • C + B • C) ⊕ D. It operates over a 2V to 5.5V supply range, making it compatible with 3.3V and 5V logic systems, and is qualified per AEC-Q100 for automotive environments. Configurable logic gates are digital ICs that let a single device implement multiple Boolean functions - MUX, AND, OR, NAND, NOR, XOR, XNOR - depending on input connections. They belong to the standard logic gate family within digital ICs, the fundamental building blocks of digital electronics. Integrating three such gates in one package saves board space and simplifies inventory versus discrete gates. Key features include Schmitt-trigger inputs on every pin, which eliminate erroneous outputs caused by slow-edged or noisy input signals - critical in electrically harsh automotive systems. The 3-state outputs place pins in a high-impedance state, enabling bus sharing. Per the TI datasheet, the device drives load capacitance up to 50pF while meeting all datasheet specifications, with a typical propagation delay of 7.5ns at 5V for high-speed operation. Technically, the device is built on TI AHC (Advanced High-Speed CMOS) technology, balancing speed with low static power consumption. Input hysteresis improves noise immunity and permits slow input transitions without false triggering, while output-enable control supports bus-oriented architectures. Typical applications include automotive body control modules, infotainment systems, and industrial automation where multiple logic functions are required in a compact footprint. It also suits signal conditioning in mixed-voltage systems. Design tip: keep total output load capacitance at or below 50pF to preserve full datasheet timing, and place a 0.1uF decoupling capacitor close to VCC to suppress supply noise.

Devis Contact
SN74AHC9541-Q1 - AEC-Q100 Octal Buffer, Schmitt | TI
SN74AHC9541-Q1

SN74AHC9541-Q1 - AEC-Q100 Octal Buffer, Schmitt | TI

The Texas Instruments SN74AHC9541-Q1 is an automotive-grade octal buffer and line driver featuring Schmitt-trigger inputs and 3-state outputs, qualified to AEC-Q100 for harsh automotive environments. It operates from a 2V to 5.5V supply, supports -40C to +125C ambient temperatures, and is offered in a wettable-flank QFN (VSSOP-20) package that enables reliable solder-joint inspection. An octal buffer is a digital logic IC providing eight independent buffering channels that isolate, amplify, and restore digital signals. Buffers sit within the standard logic family hierarchy (CMOS logic > buffers/line drivers > single gates), preventing loading effects on driving circuits and regenerating weak or degraded signals across PCB traces, cables, and backplanes. Schmitt-trigger inputs add hysteresis, converting slow or noisy input edges into clean, fast output transitions. Key features include the wide 2V to 5.5V operating range compatible with 3.3V and 5V logic systems, dual active-low output enables (OE1 and OE2) that must both be low to activate all eight outputs, and AEC-Q100 automotive qualification. According to the TI datasheet, the device drives loads with total capacitance up to 50pF while meeting all datasheet specifications; larger loads may be applied but exceeding 50pF is not recommended. Fabricated in AHC-series CMOS technology, the device delivers low static power consumption, high speed, and balanced drive. The wettable-flank QFN package improves wetting of the package edge during soldering and enables automated optical inspection (AOI), a key automotive quality requirement. Typical applications include automotive body control modules, infotainment systems, ADAS signal buffering, and industrial interfaces where slow or noisy signals must be conditioned or held during controller reset. Design tip: keep per-output capacitive loading at or below 50pF, place 0.1uF decoupling capacitors close to VCC, and tie unused inputs to VCC or GND - never leave CMOS inputs floating.

Devis Contact
SN74AHCT3G99-Q1 - Triple Configurable Gate | TI | Automotive
SN74AHCT3G99-Q1

SN74AHCT3G99-Q1 - Triple Configurable Gate | TI | Automotive

The SN74AHCT3G99-Q1 is an automotive-grade triple ultra-configurable multiple-function gate from Texas Instruments, containing three independent configurable logic gates with 3-state outputs in a 20-pin TSSOP (PW) package. Each gate has four inputs and implements the Boolean function Y = (A • /C + B • C) ⊕ D, which users can configure for functions such as MUX, AND, OR, NAND, NOR, XOR, and XNOR by appropriately strapping the inputs. A configurable multiple-function gate is a logic IC that can be wired to perform different Boolean operations, allowing one device to replace several fixed-function gates and reducing component count and board space. In the digital logic hierarchy it belongs to the configurable standard logic family, a subset of logic ICs within the broader category of integrated circuits. The SN74AHCT3G99-Q1 is part of the AHCT family - high-speed silicon-gate CMOS with TTL-compatible inputs - bridging CMOS efficiency and TTL logic levels. Key features include Schmitt-trigger inputs on all pins, which eliminate erroneous outputs caused by slow-edged or noisy input signals, and 3-state outputs that permit bus-oriented applications with high-impedance isolation. The supply range is 4.5V to 5.5V for full datasheet performance, and the device is AEC-Q100 qualified with an operating temperature range of -40C to +125C for harsh automotive environments. TI specifies the device can drive a total load capacitance of up to 50pF while meeting all datasheet specifications; larger loads are possible but not recommended. Technically, the device is fabricated in advanced CMOS, providing low static power consumption with TTL-level input thresholds. Propagation delay is [DATA_NEEDED: propagation delay] and output drive current is [DATA_NEEDED: output drive current]. The 3-state outputs are controlled via output-enable (OE) inputs, and Schmitt-trigger hysteresis of [DATA_NEEDED: hysteresis voltage] ensures clean switching on slow edges. Typical applications include automotive body control modules, infotainment units, and industrial control systems needing flexible glue logic, signal routing, or level-compatible logic functions. AEC-Q100 qualification guarantees reliability under automotive temperature, vibration, and ESD stress. When designing with this device, place decoupling capacitors close to the supply pins, keep output load capacitance at or below 50pF, and tie every OE input to a defined logic level to avoid floating bus contention.

Devis Contact
SN74AHCT7541-Q1 - Automotive Octal Buffer, Open-Drain | TI
SN74AHCT7541-Q1

SN74AHCT7541-Q1 - Automotive Octal Buffer, Open-Drain | TI

The SN74AHCT7541-Q1 from Texas Instruments is an automotive-grade octal buffer with open-drain outputs, operating from a 4.5V to 5.5V supply in a 20-pin TSSOP (PW) package. It contains eight non-inverting buffers with active-low output enable pins (OE1 and OE2); both enables must be low for the outputs to be active. When enabled, outputs actively drive low or present a high-impedance state; when disabled, outputs are high impedance. The device is AEC-Q100 qualified for a +125C ambient grade with HBM ESD protection. An octal buffer is a digital IC providing eight independent buffer channels used to increase fan-out, drive capacitive loads, or interface between voltage domains. With open-drain outputs, the device sinks current to ground when active, which makes it ideal for driving LEDs and implementing wired-OR logic. Schmitt-trigger inputs add hysteresis for superior noise immunity in automotive and industrial environments. Key features include the 4.5V to 5.5V supply range, open-drain outputs suited to external pull-up voltages above VCC, and inputs that tolerate slow edge rates thanks to Schmitt-trigger hysteresis. Per the TI datasheet, the device drives loads with total capacitance up to 50pF while meeting all datasheet specifications; larger capacitive loads are possible but not recommended. Output low-level current capability is defined by the VOL/IO characteristics in the Electrical Characteristics table. Technically, the device uses Advanced High-Speed CMOS TTL-compatible (AHCT) technology, balancing speed and power. External pull-up resistors define the output high level, a critical design consideration for wired-OR buses and mixed-voltage interfacing. The -40C to +125C operating range suits under-hood and body-electronics environments. Typical applications include automotive dashboard indicator LED drivers, level shifting between 5V and higher-voltage domains, wired-OR interrupt lines, and industrial control I/O requiring high noise immunity. Design tip: size pull-up resistors for the desired high level and sink current, tie OE1/OE2 appropriately, and place a 0.1uF decoupling capacitor close to the VCC pin.

Devis Contact
SN74ALS253 - Dual 4:1 Mux 3-State ALS TTL | Texas Instruments
SN74ALS253

SN74ALS253 - Dual 4:1 Mux 3-State ALS TTL | Texas Instruments

The Texas Instruments SN74ALS253 is a dual 1-of-4 data selector/multiplexer with 3-state outputs, fabricated in Advanced Low-Power Schottky (ALS) TTL technology and offered in 16-pin packages including Plastic DIP (N), Small-Outline (D), ceramic chip carrier (FK), and ceramic J packages. Each half multiplexes one of four data inputs to a single 3-state output under two common select lines, with separate active-low output-control (OE) inputs per section. A multiplexer is a combinational logic device that selects one of several input signals and forwards it to a single output, serving as a fundamental building block in the digital logic hierarchy between basic gates and larger bus-oriented logic systems. The 74-family lineage spans standard TTL (74), Schottky (74S), Low-Power Schottky (74LS), Advanced Low-Power Schottky (74ALS), and CMOS variants such as 74HC and 74HCT. Key features include full binary decoding with internal inverters and drivers feeding AND-OR gate structures, 3-state outputs that directly drive bus-organized data lines, and the ALS speed-power advantage over LS parts: faster propagation with substantially lower supply current. It is the 3-state version of the ALS153 and SN74AS153, permitting multiplexing from n lines to one line and parallel-to-serial conversion. Typical applications include bus-organized system data selection, parallel-to-serial data conversion, n-line to 1-line multiplexing in industrial controllers, and legacy TTL system maintenance and repair where ALS-era timing margins must be preserved. Design consideration: as an older bipolar TTL family, the SN74ALS253 requires a regulated 5V supply and presents TTL-level input thresholds; when integrating into mixed-voltage modern designs, verify logic-level compatibility or consider CMOS substitutes such as 74HC253 with attention to timing.

Devis Contact
SN74ALVCH162373 - 16-Bit 3-State Transparent Latch | TI
SN74ALVCH162373

SN74ALVCH162373 - 16-Bit 3-State Transparent Latch | TI

The Texas Instruments SN74ALVCH162373 is a 16-bit transparent D-type latch with 3-state outputs, part of the ALVCH low-voltage CMOS Widebus family. It operates from a 2.3V to 3.6V supply and can function as two independent 8-bit latches or one 16-bit latch, controlled by latch-enable (LE) and output-enable (OE) inputs. When LE is high, the Q outputs follow the D inputs; when LE is low, the outputs hold the last data. A transparent latch is a sequential logic component that passes input data to outputs while enabled and stores the last value when disabled. It sits in the hierarchy: transparent latch -> D-type latch -> latch -> sequential logic -> digital logic IC, and is a fundamental building block for data storage, synchronization, and bus interfacing in digital systems. Key features include bus-hold circuitry on data inputs, which eliminates external pull-up or pull-down resistors; equivalent 26-ohm series resistors on output ports, removing the need for external line-termination resistors; and latch-up performance exceeding 250 mA per JESD 17, plus ESD protection. The 3-state outputs allow multiple devices to share a common bus, and the Ioff feature supports partial-power-down operation without backflow current. Technically, the device uses advanced low-voltage CMOS technology, providing high speed with low static power consumption. Propagation delay is typically around 4.1 ns at 3.3V, with +/-12 mA output drive at 3.3V, suitable for moderate capacitive loads. It is characterized for operation from -40C to +85C in industrial environments. Packages include 48-SSOP (DL), 48-TSSOP (DGG/GR), and 56-BGA MicroStar Junior (KR). Typical applications per the TI datasheet include buffer registers, I/O ports, bidirectional bus drivers, and working registers in memory interfaces, data acquisition systems, and general-purpose logic. Design tip: place 0.1uF decoupling capacitors close to each VCC pin, and verify timing margins since the integrated 26-ohm output resistors slightly slow edge rates at high frequencies.

Devis Contact
SN74AUC2G34 - Dual Buffer Gate 0.8-2.7V | Texas Instruments
SN74AUC2G34

SN74AUC2G34 - Dual Buffer Gate 0.8-2.7V | Texas Instruments

The Texas Instruments SN74AUC2G34 is a dual non-inverting buffer gate from the AUC (Advanced Ultra-CMOS) logic family, performing the Boolean function Y = A in positive logic. It operates from a 0.8 V to 2.7 V supply, specifically optimized for 1.65 V to 1.95 V operation, and is offered in the 6-pin SOT-23 (DBV) and SC70/SOT-563 (DCK) surface-mount packages for space-constrained portable designs. A buffer gate is a digital logic IC that passes its input to the output without inversion while regenerating drive strength and providing signal isolation. Within the logic-IC hierarchy (buffer gate -> logic IC -> digital integrated circuit), buffers are used to drive capacitive loads, isolate buses, and restore weak or degraded signal edges in low-voltage digital systems. Key features include sub-1-V operability, 3.6-V I/O tolerance for mixed-mode signal operation, and Ioff support for partial-power-down architectures. According to the TI datasheet (Rev. B), maximum propagation delay is 1.8 ns at 1.8 V with a +/-8-mA output drive at 1.8 V and low dynamic power consumption. NanoFree package technology in the smallest variants uses the die itself as the package. Architecturally, the device uses advanced ultra-low-voltage CMOS technology for high noise immunity and low static current. Ioff circuitry disables outputs and blocks damaging backflow current when VCC is removed while inputs remain driven - critical for multi-rail systems with flexible power sequencing. Typical applications include signal buffering in smartphones and tablets, clock distribution, 1.8 V to 3.3 V domain-tolerant interfacing, and bus isolation in industrial and consumer electronics. Design tip: place a 0.1 uF decoupling capacitor close to VCC and ensure input signals never exceed the absolute maximum rating of 4.6 V.

Devis Contact