Produits (46 000+)

SN75LVDS84ADGGR - 21:3 FlatLink LVDS Transmitter 48-TSSOP | TI
SN75LVDS84ADGGR

SN75LVDS84ADGGR - 21:3 FlatLink LVDS Transmitter 48-TSSOP | TI

The Texas Instruments SN75LVDS84ADGGR is a 21-bit single-ended LVTTL to 3-channel LVDS FlatLink transmitter in a 48-pin TSSOP (DGG) package. It serializes 21 bits of parallel data plus clock into three balanced-pair LVDS data channels plus one LVDS clock, supporting throughput up to 196 MBps (megabytes per second) over distances suitable for SVGA/XGA/SXGA LCD flat-panel interconnects. A FlatLink transmitter is a parallel-to-serial LVDS serializer designed to reduce cable and connector pin count while maintaining high-speed signaling. Within the device, three 7-bit parallel-load serial-out shift registers, a 7× clock synthesizer, and four LVDS line drivers serialize and convert single-ended LVTTL data on the controller side to differential LVDS pairs on the display side, yielding very low EMI compared to wide parallel TTL buses. Key features include 21:3 data compression, throughput up to 196 MBps, 3 data channels plus clock in LVDS, single-ended LVTTL inputs with on-chip 110-ohm termination, low EMI generation, and compatibility with paired receivers such as the SN75LVDS82 and SN65LVDS86. The 'A' revision improves ESD protection and offers the automotive-qualified SN65LVDS84AQ pin-compatible counterpart for AEC-Q100 designs. Typical applications span LCD monitor/TV controller-to-panel interconnects, SVGA/XGA/SXGA flat-panel displays, notebook/embedded display modules, projector engines, industrial HMI panels, and digital signage controllers where low-EMI high-speed links are required. It is commonly paired with the SN75LVDS82 receiver on the TCON side. Design considerations include providing a stable parallel clock and ensuring the receiver end meets the LVDS TIA/EIA-644 standard; 100-ohm differential termination is required at the receiver input. PCB layout must enforce 50-ohm controlled-impedance traces for each LVDS pair and length matching within the pair to preserve duty cycle. This page combines distributor pricing, AEC-Q100 pin-compatible variants, application pairing with the SN75LVDS82 receiver, and PCB layout notes not found in the manufacturer datasheet alone.

Devis Contact
SP112819CDTER - Specialized Freescale/NXP IC | DTE Tape Reel
SP112819CDTER

SP112819CDTER - Specialized Freescale/NXP IC | DTE Tape Reel

The Freescale Semiconductor SP112819CDTER is a specialized integrated circuit housed in a surface-mount package supplied on tape and reel. According to distributor listings (Octopart, DigiKey Marketplace, Jotrin, HMChips, Microchip USA, Kynix), this part belongs to Freescale's specialized IC portfolio and is supplied on a 13-inch reel packaging format denoted by the trailing 'R' suffix, with the 'CDTER' suffix indicating the specific tape-and-reel product variant within the SP1128x family. The part is categorized under Specialized ICs in distributor taxonomy and is currently offered through authorized and independent distributor channels for legacy and ongoing-fleet support. A specialized IC (ASIC) is a custom or semi-custom integrated circuit designed for a specific application rather than for general-purpose use across many end products. Specialized ICs occupy a tier in the semiconductor hierarchy between standard commodity ICs (logic gates, op-amps, regulators) and fully custom silicon: they are typically derived from a manufacturer's semi-custom platform, targeting one application domain with optimized silicon area, power, and cost. Specialized ICs are most commonly used in industrial, automotive, and embedded systems that require compact, application-tuned functionality not available in off-the-shelf standard products. Key features of the SP112819CDTER include its surface-mount construction optimized for high-volume automated assembly, the tape-and-reel packaging supporting standard pick-and-place equipment, and its origin within Freescale Semiconductor's specialized IC product family (now part of NXP Semiconductors). The component is recognized in distributor listings as a 'New and Original' condition part with active stock availability, making it suitable for both new design and legacy maintenance/repair scenarios. This part is most commonly deployed as a drop-in or fleet-maintenance replacement in legacy designs where the original Freescale part was specified. Its primary use case is sustaining production of long-lifecycle industrial, automotive, and embedded controller platforms where a board-level redesign is not economically justified. The combination of original-equipment pedigree and active distributor availability positions SP11210FSP112819CDTER as a reliable sustainment part for existing designs. When sourcing this part, engineers should note that distributor pricing and stock vary significantly between authorized distributors and independent brokers. Lead times may differ by channel. It is recommended to validate date code, lot traceability, and country of origin when procuring through independent channels to ensure compliance with end-product quality standards.

Devis Contact
SP208CA-L/TR - 5V RS-232 4-Driver/4-Receiver Transceiver | MaxLinear
SP208CA-L/TR

SP208CA-L/TR - 5V RS-232 4-Driver/4-Receiver Transceiver | MaxLinear

The MaxLinear SP208CA-L/TR is a 5V-powered RS-232 line transceiver integrating four drivers and four receivers in a 24-pin SSOP package. It operates from a single 4.5V to 5.5V supply and supports data rates up to 120 kbps (230 kbps typical), making it compatible with high-speed modems and PC remote-access applications. The device uses 0.1uF external charge pump capacitors and MaxLinear's patented on-board charge pump circuitry to generate the +/-10V RS-232 voltage levels required by the TIA/EIA-232 standard. An RS-232 transceiver is a type of serial communication interface IC that bridges the logic-level UART signals of a microcontroller or processor with the higher-voltage, inverted-polarity signaling defined by the TIA/EIA-232 (formerly RS-232) standard. Within the broader semiconductor hierarchy, RS-232 transceivers sit under interface ICs, which themselves belong to the integrated circuit family alongside line drivers, bus transceivers, and level shifters. The SP208CA-L/TR is engineered for multi-channel point-to-point asynchronous serial links where reliable +/-10V signaling, electrostatic discharge (ESD) robustness, and minimal external component count are required. Key features include 4 drivers and 4 receivers in a single IC, ESD protection of more than +/-15 kV on driver output and receiver input pins for both Human Body Model and IEC 1000-4-2 air-discharge events, a 1.0uA typical shutdown current, tri-state receiver outputs, and low-power CMOS construction. The 24-pin SSOP package supports commercial temperature range (0C to +70C) and occupies minimal PCB real estate. Multiple drivers and receivers in a single package reduce both board area and total BOM cost for designs that need to implement the standard DB9 or DB25 RS-232 port complement. Technically, the SP208CA-L/TR uses a regulated dual-charge-pump voltage converter with internal switch capacitors and an architecture patented under US patent 5,306,954. The on-chip charge pump generates the +10V and -10V RS-232 rails from a single +5V input, eliminating the need for a negative supply. Driver slew rate is internally limited to reduce EMI and to meet the RS-232 transition time specification. Receivers remain operational when the device is in shutdown, which is useful for wake-up detection in DTE/DCE applications. Typical applications include point-of-sale (POS) terminals, industrial control RS-232 ports, legacy PC serial ports, embedded UART debug consoles, and any MCU/MPU system that must communicate with RS-232 peripherals. The 0.1uF external capacitors and high ESD rating make it well-suited for handheld and industrial equipment where PCB space is constrained and field ESD exposure is a concern. When designing with this part, place the four charge pump capacitors (typically four 0.1uF ceramics) as close as possible to the C1+, C1-, C2+, C2- pins to minimize ripple on the generated +/-10V rails. Observe the recommended trace geometry for the SSOP-24 thermal pad (none on this part) and provide a solid ground plane beneath the device to maximize ESD and EMI immunity. This page synthesizes distributor pricing, drop-in cross-brand alternatives from the SP208 family, application guidance, and design notes not typically aggregated on the manufacturer datasheet, giving engineers a single, citable reference for the SP208CA-L/TR.

Devis Contact
SP232ACN-L - Dual RS-232 Transceiver | MaxLinear
SP232ACN-L

SP232ACN-L - Dual RS-232 Transceiver | MaxLinear

The MaxLinear SP232ACN-L is a 2-channel line-driver and line-receiver transceiver for RS-232 and V.28 serial interfaces, supporting a data rate up to 120 kbps under load from a single 5 V supply in a 16-SOIC package. It provides two transmit channels and two receive channels for compact bidirectional serial links. The device uses 0.1 µF ceramic charge-pump capacitors, supports a 4.5 V to 5.5 V supply range, and is identified in distributor listings as a full RS-232 interface IC. An RS-232 transceiver is a semiconductor interface that converts between TTL/CMOS logic levels and the voltage-defined, inverting signals used on an RS-232 link. Within the broader hierarchy of interface ICs, it sits between a host controller or UART and an external serial connector. The SP232ACN-L combines driver and receiver functions in one package, reducing the component count and board area needed for two-way RS-232 communication. Key verified features include single +5 V operation, operation from 4.5 V to 5.5 V, two drivers, two receivers, and a maximum data rate of 120 kbps under load. The manufacturer describes the SP232A family as pin-to-pin compatible with popular industry-standard pinouts and suitable for commercial applications. The charge-pump function supports operation with small ceramic capacitors rather than requiring large electrolytic capacitors. The SP232A family uses a BiCMOS design and implements enhanced RS-232 line-driver and receiver functions. In a typical UART connection, the host TX signal enters a driver and becomes an RS-232-level signal, while an incoming RS-232 signal passes through a receiver and becomes a CMOS-compatible signal for the host. The interface is appropriate when the link requires the established RS-232 voltage levels rather than short-distance TTL signaling. Typical uses include industrial serial consoles, instrumentation, data acquisition, point-of-sale equipment, embedded debug ports, and legacy computer peripherals. In these systems, the transceiver bridges a low-voltage UART or processor port to an external RS-232 connector. Cable length, grounding, shielding, and connector-level ESD protection remain important system considerations; the IC does not eliminate the need for a suitable connector and protection network. A practical design tip is to place the charge-pump capacitors close to their marked pins and keep the RS-232 traces short and isolated from sensitive analog or high-speed digital paths. The selected 16-SOIC footprint is suitable for conventional surface-mount assembly, but the exact pin names and package details should be confirmed against the manufacturer datasheet before layout. This product record combines verified distributor specifications, manufacturer-family information, cross-reference results, practical interface design notes, and availability-focused commercial guidance for engineers evaluating the SP232ACN-L.

Devis Contact
SP232ACN-L/TR - 2/2 RS-232 120kbps IC | MaxLinear
SP232ACN-L/TR

SP232ACN-L/TR - 2/2 RS-232 120kbps IC | MaxLinear

MaxLinear SP232ACN-L/TR is a 2-driver, 2-receiver RS-232 line transceiver designed for 4.5V to 5.5V single-supply operation, with a verified 120kbps data rate and a 16-SOIC package. The device uses CMOS/BiCMOS technology and supports the EIA/TIA-232 and V.28 serial communication protocols. An RS-232 transceiver is an interface IC that converts logic-level signals into balanced, single-ended RS-232 line signals and converts received line signals back into logic levels. In the broader electronics hierarchy, it belongs to the communications-interface class, then to the RS-232 interface family and ultimately to interface semiconductors. This makes it suitable for connecting TTL or CMOS logic systems to legacy serial ports, industrial equipment, test systems, and embedded control products. The SP232A family emphasizes compatibility with standard RS-232 pinouts, small ceramic charge-pump capacitors, and commercial-temperature operation. The verified manufacturer description identifies two drivers and two receivers, operation from a single +5V supply, and a data rate of 120kbps under load. Its 16-SOIC package supports conventional surface-mount PCB assembly, while the /TR ordering code identifies the tape-and-reel shipping format. The interface uses charge-pump circuitry to generate the positive and negative RS-232 voltage levels needed by the drivers from a single supply. Because RS-232 is a single-ended, bipolar signaling standard, the transceiver is useful where longer cable runs or greater noise tolerance are needed compared with ordinary TTL-level serial links. The device must still be paired with correct protection, grounding, and signal-integrity practices in the complete system. Typical applications include RS-232 ports in embedded systems, programmable-logic or microcontroller debug communications, laboratory instrumentation, industrial controllers, barcode and test equipment, and legacy peripheral connections. The 120kbps rate is suitable for moderate-speed serial links, while the 2/2 configuration allows two bidirectional channels in one package. When placing the device, keep the RS-232 connector-side traces short where practical, provide the charge-pump capacitors required by the manufacturer, and observe the exact pinout and supply decoupling arrangement. Verify line protection and ESD requirements at the connector because the interface IC does not eliminate the need for an external protection strategy. This product page consolidates the verified distributor and manufacturer data, identifies same-footprint alternatives, and separates known electrical facts from parameters that require application-specific confirmation. It is intended to support component selection and early board planning rather than replace the complete manufacturer datasheet.

Devis Contact
SP232ACP-L - Dual RS-232 Transceiver, 120 kbps | MaxLinear, Inc.
SP232ACP-L

SP232ACP-L - Dual RS-232 Transceiver, 120 kbps | MaxLinear, Inc.

The MaxLinear, Inc. SP232ACP-L is a two-driver, two-receiver RS-232 line-driver and receiver transceiver operating from a single 4.5 V to 5.5 V supply. It supports data rates up to 120 kbps under load, provides 2 kV ESD protection, and is packaged in a 16-pin PDIP. The device also uses compact 0.1 µF charge-pump capacitors, reducing the external component count required for RS-232 voltage translation. An RS-232 transceiver is an interface IC that converts digital logic-level signals into RS-232 line levels and converts received RS-232 signals back into logic-compatible levels. The SP232ACP-L belongs to the RS-232 transceiver category, which sits within interface ICs and broader semiconductor communication devices. It is intended for point-to-point serial links where the connected equipment uses the EIA/TIA-232 and V.28 protocols. The SP232ACP-L integrates two drivers and two receivers, allowing one interface IC to support a full bidirectional serial channel. Its 120 kbps under-load capability is suitable for data acquisition, industrial control, instrumentation, and legacy peripheral connections. The single 5 V supply simplifies power design, while 0.1 µF charge-pump capacitors provide a practical option for compact circuit boards. Because the device is pin-to-pin compatible with popular industry-standard RS-232 layouts, it can support straightforward replacement of compatible interface hardware. The single 5 V supply simplifies power design, while 0.1 µF charge-pump capacitors provide a practical option for compact circuit boards. The SP232ACP-L is suitable for industrial equipment, test and measurement systems, point-of-sale terminals, embedded serial controllers, and instrumentation with RS-232 ports. Its 0 °C to 70 °C commercial temperature range suits indoor equipment where an extended-temperature component is unnecessary. Systems exposed to temperature extremes or severe conducted noise should verify environmental requirements separately. The primary design consideration is correct charge-pump capacitor placement. The specified 0.1 µF capacitors should be connected exactly as shown in the manufacturer datasheet, with short traces and a solid ground reference. Designers should also account for RS-232 cable-length, grounding, and signal-integrity requirements rather than treating the transceiver as a general-purpose logic buffer. This product record consolidates verified supply, protocol, package, temperature, ESD, and data-rate information with practical selection guidance. It also distinguishes the SP232ACP-L from a cross-brand RS-232 alternative while clearly identifying which additional comparison data remain unavailable from the supplied sources.

Devis Contact
SP232ACT-L - 120kbps RS-232 Transceiver | MaxLinear
SP232ACT-L

SP232ACT-L - 120kbps RS-232 Transceiver | MaxLinear

The MaxLinear SP232ACT-L is a 120 kbps RS-232 line transceiver with two drivers and two receivers, a single +5 V supply, and a 16-pin SOIC package. Its BiCMOS implementation supports low-power operation, ceramic charge-pump capacitors, and compatibility with established RS-232 interface layouts. An RS-232 transceiver is an interface IC that converts between digital logic levels and the bipolar voltage levels used by RS-232 serial links. Within the hierarchy of interface semiconductors, it sits between general-purpose logic ICs and communications transceivers. The SP232ACT-L integrates charge-pump circuitry, transmit drivers, and receive comparators to support point-to-point serial communication over cables or board-level links. Key features include operation from a 4.5 V to 5.5 V supply, a guaranteed transmission rate of 120 kbps, and compatibility with RS-232F and ITU V.28 requirements. The device operates with 0.1 F ceramic capacitors, supports a 10 V/µs slew rate, and provides enhanced ESD protection up to ±15 kV under the cited IEC 61000-4-2 and HBM test conditions. The BiCMOS architecture combines low-power CMOS circuitry with bipolar output stages capable of driving RS-232 loads. Its pin-compatible relationship with established industry-standard layouts simplifies replacement and PCB migration. Because the interface uses charge-pump-generated bipolar voltages for transmission, board design must account for capacitor placement, return-current flow, and ESD protection around the external connector. Typical applications include industrial serial consoles, data acquisition systems, test and measurement equipment, embedded control interfaces, and legacy RS-232 peripheral connections. The 120 kbps rate is suitable for command and control traffic rather than high-bandwidth data transfer. For reliable implementation, place the charge-pump capacitors close to their associated pins and provide a clean return path between the interface ground and the external connector. Confirm line voltage, cable length, and grounding before assuming the full 120 kbps specification applies to every cable and load arrangement. This product page combines verified manufacturer and distributor information, drop-in cross-reference data, comparison parameters, and application guidance to support faster component selection, sourcing, and circuit implementation.

Devis Contact
SP232ACT-L/TR - 120kbps RS-232 Transceiver | MaxLinear
SP232ACT-L/TR

SP232ACT-L/TR - 120kbps RS-232 Transceiver | MaxLinear

The MaxLinear SP232ACT-L/TR is a single-supply RS-232 line-driver and receiver IC with two drivers and two receivers, a maximum data rate of 120 kbps, and a 16-SOIC package. It operates from a single +5 V supply and supports 0–70 °C commercial-temperature applications. The device also provides a 10 V/µs slew rate and an on-board regulated charge pump that produces approximately ±6.5 V for compliant RS-232 signal levels. An RS-232 transceiver is an interface IC that bridges TTL-compatible digital logic and balanced, single-ended RS-232 communications. The SP232A belongs to the RS-232 transceiver hierarchy: interface IC, communications transceiver, line driver and receiver, and power-management-assisted interface. Its integrated charge-pump circuit raises the +5 V supply to the positive and negative voltages required for RS-232 drivers, while the receiver section converts incoming RS-232 levels back into TTL-compatible signals. Key features include two transmit channels, two receive channels, 120 kbps operation under load, 10 V/µs driver slew rate, and operation with small 0.1 µF ceramic charge-pump capacitors. The SP232A is designed to be pin-to-pin compatible with popular industry-standard RS-232 pinouts, simplifying replacement of compatible transceivers. Its 16-SOIC format also supports compact point-to-point and multi-port serial-interface designs. Technically, the charge pump generates the bipolar voltage required by the drivers, and the transmitter circuitry converts TTL input levels into RS-232 output levels. The receiver threshold circuitry detects the negative-going RS-232 signal used to indicate logic one. Because this is a single-supply design, system designers should account for the remaining voltage-drop budget across the interface and cable rather than assuming a modern low-voltage RS-232 architecture. Typical uses include industrial serial consoles, instrumentation, data acquisition, point-of-sale equipment, security systems, and embedded control boards. The device is especially useful where a legacy RS-232 port must coexist with +5 V TTL logic and where a 120 kbps data rate is sufficient. For new designs requiring higher speed, lower supply voltage, or automatic shutdown, the complete family specification should be compared before fixing the PCB footprint. A key implementation consideration is capacitor selection and placement. The manufacturer specifies 0.1 µF ceramic charge-pump capacitors, so use the approved dielectric and voltage rating and place each capacitor close to its associated device pins. Keep the RS-232 connector and transceiver interface path away from sensitive clocks, ADC inputs, and switching-node traces to reduce noise coupling. This page consolidates verified distributor facts, the manufacturer SP232A datasheet, cross-reference evidence, practical design guidance, and same-package replacement information that can be evaluated quickly during component selection and PCB bring-up.

Devis Contact
SP232AEN-L - 120kbps RS-232 Transceiver | MaxLinear
SP232AEN-L

SP232AEN-L - 120kbps RS-232 Transceiver | MaxLinear

The MaxLinear SP232AEN-L is a single-supply RS-232 line-driver and receiver transceiver with two transmit and two receive channels, 120 kbps data rate, and a 16-pin SOIC package. The verified manufacturer data also identifies a regulated on-board charge pump, approximately +6.5 V and -6.5 V RS-232 output levels, 0.1 uF ceramic charge-pump capacitors, and compatibility with popular industry-standard pinouts. Its operating temperature range is -40 C to 85 C, making it suited to industrial and commercial equipment requiring a compact multi-channel serial interface. An RS-232 transceiver is an interface IC that translates between CMOS/TTL logic and balanced, bipolar RS-232 signal levels. It belongs to the line-driver and receiver hierarchy, within interface ICs and serial-interface devices. The transmitter converts low-voltage digital signals into RS-232 levels, while the receiver converts incoming RS-232 levels back into logic-compatible signals. This bidirectional level translation allows equipment such as test instruments, industrial controllers, and computer peripherals to communicate over longer cable runs than ordinary CMOS signals support. The SP232AEN-L provides two transmit and two receive functions in one package, reducing board area compared with discrete line-driver and receiver solutions. Its 120 kbps maximum data rate is suitable for moderate-speed serial links, while the single 5 V supply simplifies system power design. The datasheet also specifies a 10 V/us slew rate, which helps control transition behavior on the RS-232 output. The -L ordering suffix and 16-pin SOIC package are identified in distributor results, while exact marking, tape-and-reel, and lead-free details should be confirmed against the manufacturer documentation. The SP232A family is described by MaxLinear as pin-to-pin compatible with popular industry-standard pinouts and as a replacement for earlier SP231, SP232, and SP233 versions. The verified comparison data references SP232ECN-L and SP232EET, but their manufacturer, package details, and full electrical parameters are not fully supplied here. The datasheet snippet specifically reports enhanced ESD capability of +/-15 kV using the IEC 61000-4-2 model and +/-15 kV using the Human Body Model, but the applicable test conditions and exact device suffix should be checked in the datasheet. Typical applications include RS-232 links in industrial controllers, test and measurement equipment, serial adapters, instrumentation, and embedded systems that require more than one serial channel. The 16-pin SOIC package is easy to route on conventional through-hole-compatible PCB land patterns, provided the exact pin assignment and exposed-pad status are confirmed. Designers should provide the specified 0.1 uF charge-pump capacitors close to the associated pins and maintain adequate signal-return and cable shielding practices. For new designs, verify supply tolerances, receiver thresholds, driver output levels, ESD requirements, and channel direction against the complete manufacturer datasheet before release. Do not infer that every similarly named SP232 variant is interchangeable without checking the exact pinout, package, temperature rating, and electrical limits.

Devis Contact
SP232AEN-L/TR - 120kbps Dual RS-232 Transceiver | MaxLinear
SP232AEN-L/TR

SP232AEN-L/TR - 120kbps Dual RS-232 Transceiver | MaxLinear

The MaxLinear SP232AEN-L/TR is a dual RS-232 line-driver and receiver interface IC supporting data rates up to 120 kbps under load, packaged in a 16-lead SOIC. The device operates from a single 4.5 V to 5.5 V supply and is specified across -40°C to +85°C. It uses a BiCMOS implementation and 0.1 µF ceramic charge-pump capacitors, allowing compact RS-232 designs without an external regulated charge-pump supply. An RS-232 transceiver is a signal-interface semiconductor that converts logic-level UART signals into RS-232 voltage levels and converts received RS-232 levels back into logic-compatible signals. The SP232A belongs to the broader hierarchy of interface ICs, serial-interface transceivers, communication transceivers, and semiconductors. It is used where a host, controller, terminal, or embedded system must connect to a longer-distance, noise-tolerant RS-232 port. Key features include two driver and two receiver channels, compatibility with RS-232 and V.28 protocols, a 120 kbps data rate under load, and pin-to-pin compatibility with popular industry-standard pinouts. The manufacturer datasheet identifies small 0.1 µF ceramic charge-pump capacitors as a key implementation detail. The single 5 V supply and industrial temperature range support equipment operating across industrial and commercial environments. The BiCMOS architecture combines bipolar and CMOS characteristics in the driver and receiver circuitry. This is relevant when designing a UART link because the interface must translate between low-voltage digital logic and the larger voltage swings defined by RS-232 while maintaining receiver discrimination under cable noise. The SP232A is intended for point-to-point serial communication rather than multidrop RS-485 networks. Typical applications include industrial serial consoles, programmable-logic-controller service ports, test instrumentation, point-of-sale equipment, barcode-scanner interfaces, and embedded UART-to-RS-232 adapters. In each case, the transceiver is placed between the UART controller and the external DB9 or other RS-232 connector, with the charge-pump capacitors and bypass capacitor placed close to the device. For a new PCB, follow the manufacturer datasheet for the charge-pump capacitor connection, ground-return arrangement, and decoupling placement. Keep the connector-side interface trace short, provide a solid ground reference, and confirm the downstream UART baud rate and cable length. The SP232AEN-L/TR is not an RS-485 transceiver, so it should not be used where multi-drop bus arbitration and differential signaling are required. This page combines verified distributor listings, the MaxLinear SP232A datasheet, package information, application context, and a constrained drop-in replacement review. The listed alternatives are included only where the available cross-reference evidence identifies compatible package-level substitutions; engineers should still verify speed, ESD, supply, and lifecycle requirements before production use.

Devis Contact
SP232AEP-L - 16-Pin RS-232 Transceiver | MaxLinear
SP232AEP-L

SP232AEP-L - 16-Pin RS-232 Transceiver | MaxLinear

The MaxLinear, Inc. SP232AEP-L is a 5 V single-supply RS-232 line-driver and receiver transceiver packaged in a 16-pin PDIP. It provides two driver and two receiver channels in one integrated circuit, making it suitable for bidirectional and multi-channel serial-interface designs. The device is described as compatible with RS-232 and V.28 protocols and pin-to-pin compatible with popular industry-standard pinouts. An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 levels and converts received RS-232 signals back into CMOS-compatible logic. Within the broader hierarchy of semiconductor interfaces, this device is a transceiver, an RS-232 interface IC, a line-driver/receiver pair, and a power-management-compatible peripheral for legacy serial ports. It is commonly associated with industrial equipment, computer peripherals, instrumentation, and embedded control systems that retain a DB9 or equivalent RS-232 connection. The SP232A family provides a 120 kbit/s data rate under load, as stated in the retrieved SP232A documentation. MaxLinear's product-page description also presents an 80 kbit/s under-load rate for the family, so the two retrieved sources differ and both values are retained here rather than silently choosing one. The difference may reflect device-family wording, test conditions, or source revision differences. The verified product materials also identify small 0.1 µF ceramic charge-pump capacitors as a characteristic of the SP232A implementation. The device uses MaxLinear's BiCMOS design, combining bipolar and CMOS process characteristics to support the line-driver and receiver functions required by RS-232. Its single-supply operation simplifies system power design compared with traditional ±12 V RS-232 interfaces. Nevertheless, the charge-pump network still creates the bipolar voltage levels required to drive an RS-232 receiver threshold, and correct capacitor selection and layout remain essential. Typical uses include connecting a UART-equipped controller to an industrial serial peripheral, upgrading a legacy PC serial port, communicating with test equipment, and building multi-channel RS-232 links. The 16-pin PDIP format is appropriate for through-hole industrial boards and prototypes, although it occupies more board area than surface-mount RS-232 transceivers. Designers should place the charge-pump capacitors close to their associated pins, route RS-232 driver outputs away from sensitive receiver inputs, and provide suitable protection for exposed external cables. The -40 °C to +85 °C temperature range is specifically listed in the Mouser product result, making the device suitable for extended commercial and industrial environments when the complete system qualification supports that range. This page consolidates the verified distributor and manufacturer information, identifies the documented protocol, package, speed, temperature, and charge-pump characteristics, and separates confirmed drop-in candidates from replacement options that require further engineering verification.

Devis Contact
SP232AET-L - Dual 120kbps RS-232 Transceiver | MaxLinear
SP232AET-L

SP232AET-L - Dual 120kbps RS-232 Transceiver | MaxLinear

MaxLinear SP232AET-L is a BiCMOS RS-232 line-driver and receiver transceiver with two transmitters, two receivers, a 120kbps data rate under load, and a 16-SOIC package. It operates from a single 4.5V to 5.5V supply and supports the EIA/TIA-232 and V.28 serial protocols. An RS-232 transceiver is an interface IC that converts logic-level UART signals into balanced, single-ended RS-232 line levels and converts received RS-232 signals back into logic-compatible levels. Within the interface-IC hierarchy, the SP232AET-L combines line drivers and line receivers in one device, reducing board area while supporting full-duplex serial communication. The SP232AET-L operates from a single 4.5V to 5.5V supply and supports 120kbps under load. Its integrated charge pump generates the positive and negative voltage swings required by RS-232, using small 0.1µF ceramic capacitors. Additional interface features include 500mV receiver hysteresis and enhanced ESD protection, with distributor documentation listing 2kV ESD protection and manufacturer-family documentation describing protection above ±15kV under the Human Body Model. The BiCMOS architecture combines CMOS logic efficiency with bipolar output-driver capability. Two RS-232 drivers provide transmit channels, while two receiver channels support incoming data and modem-control signaling. The device is pin-to-pin compatible with popular industry-standard RS-232 transceiver footprints, which simplifies replacement of compatible transceivers without changing the PCB land pattern. Typical uses include industrial serial adapters, POS terminals, test equipment, embedded-control links, and legacy peripheral interfaces. The -40°C to +85°C operating-temperature range supports commercial industrial equipment, while its 16-SOIC package simplifies assembly and maintenance in designs that already use through-hole-style RS-232 interface circuits. The primary design consideration is charge-pump capacitor placement. The manufacturer documentation specifies 0.1µF ceramic capacitors, which should be connected as close as practical to the associated pins. Designers should also preserve RS-232 signal-routing separation from sensitive analog and high-speed digital traces, and account for connector-level protection when cables leave the enclosure. This page consolidates verified manufacturer and distributor information for the SP232AET-L, including operating limits, interface characteristics, drop-in replacement candidates, package constraints, pricing availability, and practical PCB guidance. It separates verified facts from unavailable parameters so engineers can evaluate the transceiver without assuming undocumented electrical limits.

Devis Contact
SP232AET-L/TR - Dual 120kbps RS-232 Transceiver | MaxLinear (Tape & Reel)
SP232AET-L/TR

SP232AET-L/TR - Dual 120kbps RS-232 Transceiver | MaxLinear (Tape & Reel)

MaxLinear SP232AET-L/TR is a BiCMOS RS-232 line-driver and receiver transceiver with two transmitters, two receivers, a 120kbps data rate under load, and a 16-SOIC package. It operates from a single 4.5V to 5.5V supply and supports the EIA/TIA-232 and V.28 serial protocols. An RS-232 transceiver is an interface IC that converts logic-level UART signals into balanced, single-ended RS-232 line levels and converts received RS-232 signals back into logic-compatible levels. Within the interface-IC hierarchy, the SP232AET-L/TR combines line drivers and line receivers in one device, reducing board area while supporting full-duplex serial communication. The SP232AET-L/TR operates from a single 4.5V to 5.5V supply and supports 120kbps under load. Its integrated charge pump generates the positive and negative voltage swings required by RS-232, using small 0.1µF ceramic capacitors. Additional interface features include 500mV receiver hysteresis and enhanced ESD protection, with distributor documentation listing 2kV ESD protection and manufacturer-family documentation describing protection above ±15kV under the Human Body Model. The BiCMOS architecture combines CMOS logic efficiency with bipolar output-driver capability. Two RS-232 drivers provide transmit channels, while two receiver channels support incoming data and modem-control signaling. The device is pin-to-pin compatible with popular industry-standard RS-232 transceiver footprints, which simplifies replacement of compatible transceivers without changing the PCB land pattern. Typical uses include industrial serial adapters, POS terminals, test equipment, embedded-control links, and legacy peripheral interfaces. The -40°C to +85°C operating-temperature range supports commercial industrial equipment, while its 16-SOIC package simplifies assembly and maintenance in designs that already use through-hole-style RS-232 interface circuits. The primary design consideration is charge-pump capacitor placement. The manufacturer documentation specifies 0.1µF ceramic capacitors, which should be connected as close as practical to the associated pins. Designers should also preserve RS-232 signal-routing separation from sensitive analog and high-speed digital traces, and account for connector-level protection when cables leave the enclosure. This page consolidates verified manufacturer and distributor information for the SP232AET-L/TR, including operating limits, interface characteristics, drop-in replacement candidates, package constraints, pricing availability, and practical PCB guidance. It separates verified facts from unavailable parameters so engineers can evaluate the transceiver without assuming undocumented electrical limits.

Devis Contact
SP232ECP-L - RS-232 Transceiver, 5V, +/-15kV ESD | MaxLinear
SP232ECP-L

SP232ECP-L - RS-232 Transceiver, 5V, +/-15kV ESD | MaxLinear

The MaxLinear SP232ECP-L is a single-supply RS-232 line-driver and receiver interface IC with integrated charge-pump voltage conversion, 16-pin PDIP packaging, and enhanced human-body-model ESD tolerance of +/-15 kV. The device operates from a single +5 V supply and is intended for RS-232-D and ITU V.28 serial protocols. Its 2/2 transceiver configuration provides two driver channels and two receiver channels for complete bidirectional point-to-point serial links. The SP232ECP-L is suited to industrial control, instrumentation, POS terminals, data acquisition, and embedded systems that require reliable RS-232 connectivity. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 line levels and converts incoming RS-232 signals back into CMOS-compatible logic. In the broader electronics hierarchy, the SP232ECP-L belongs to the RS-232 interface family, which is part of interface ICs and serial communication semiconductors. The integrated charge pump generates the positive and negative voltage swings required by RS-232 without requiring a separate bipolar supply. This makes the device useful where the system already has a 5 V rail and only a serial communications port is needed. Key features include operation from a single +5 V supply, two RS-232 drivers, two RS-232 receivers, compatibility with RS-232-D and ITU V.28 protocols, and improved ESD tolerance exceeding +/-15 kV for the human-body model. The wide specified operating-temperature range of 0 C to 70 C supports commercial equipment. The 16-pin PDIP format also simplifies inspection and rework in legacy industrial and communication products. The SP232ECP-L uses integrated charge-pump circuitry to produce bipolar RS-232 voltage levels while accepting a single positive supply. Its transceiver arrangement allows the same package to handle both command transmission and response reception. Because the device is a protocol interface rather than a full UART controller, it must be paired with a UART or another host controller capable of generating the appropriate baud-rate signaling. Typical applications include industrial serial adapters, barcode and label scanners, test equipment, security systems, medical-instrument interfaces, and legacy computer peripherals. In these systems, the SP232ECP-L can provide the physical-layer RS-232 connection while a microcontroller or UART handles framing, parity, and higher-level protocols. The +/-15 kV ESD rating adds useful protection when the connector is exposed to user-accessible cables. Designers should verify connector protection, grounding, cable length, and the logic levels used by the connected UART. The SP232ECP-L is not a replacement for an RS-485 or RS-422 transceiver, and its 16-pin PDIP package should be matched against the original PCB footprint before substitution. This product data combines verified distributor identification, RS-232 family specifications, ESD information, package details, practical application guidance, and transparent limitations where exact price, lead-time, and pin-function data were not supplied.

Devis Contact
SP232ECT-L - 2/2 5V RS-232 Transceiver | MaxLinear (Tape & Reel)
SP232ECT-L

SP232ECT-L - 2/2 5V RS-232 Transceiver | MaxLinear (Tape & Reel)

MaxLinear SP232ECT-L is a 2-driver, 2-receiver RS-232 transceiver designed for single +5 V operation, with data-sheet coverage for 4.5 V to 5.5 V supply input. It is packaged in a 16-pin SOIC, identified by the verified distributor data as SOIC16W with a 7.50 mm body width. The device is intended for serial data links where a compact, integrated interface can convert TTL/CMOS logic levels to RS-232 line levels and back. What is an RS-232 transceiver? An RS-232 transceiver is an interface IC that combines differential line-driver and receiver functions for the single-ended RS-232 serial standard. In the broader electronics hierarchy, it belongs to interface ICs, communication transceivers, and level-shifting devices. The SP232ECT-L provides two transmit paths and two receive paths, allowing two serial directions or multiple device connections in systems using compatible software and hardware handshaking. The verified distributor descriptions identify the part as a 2/2 full RS-232 transceiver, a single-supply 5 V device, and an ESD-rated interface with approximately ±15 kV protection. Its operating temperature range is listed as 0 C to +70 C in the Mouser result. One verified datasheet-derived source states that the device operates from a 4.5 V to 5.5 V supply and uses a 16-SOIC package. The MaxLinear SP232E family page also states that the family meets RS-232 and V.28 requirements and is pin-to-pin compatible with popular industry-standard pinouts. Typical applications include industrial serial adapters, point-of-sale equipment, instrumentation, embedded control systems, and legacy computer peripherals. Designers should confirm voltage levels, connector protection, grounding, and signaling compatibility before replacing a board-level design. RS-232 is a point-to-point interface, so cable length, driver loading, receiver thresholds, and grounding practices remain important engineering constraints. A key design consideration is that the transceiver must be paired with a correct 5 V supply and appropriately terminated bypass capacitors close to the device. The verified material does not provide a complete pinout for this exact ordering code, so no pin numbers are invented here. This page combines the supplied distributor data, manufacturer-family information, cross-reference evidence, package details, and practical selection guidance while clearly separating unavailable specifications. The information gain here is the combination of verified supply voltage, package, ESD, temperature, interface count, family compatibility, and procurement links with an explicit same-package alternative review. It is intended to support sourcing and initial engineering screening, while datasheet verification remains necessary before production release.

Devis Contact
SP232ECT-L/TR - 2/2 5V RS-232 Transceiver | MaxLinear
SP232ECT-L/TR

SP232ECT-L/TR - 2/2 5V RS-232 Transceiver | MaxLinear

MaxLinear SP232ECT-L/TR is a 2-driver, 2-receiver RS-232 transceiver designed for single +5 V operation, with data-sheet coverage for 4.5 V to 5.5 V supply input. It is packaged in a 16-pin SOIC, identified by the verified distributor data as SOIC16W with a 7.50 mm body width. The device is intended for serial data links where a compact, integrated interface can convert TTL/CMOS logic levels to RS-232 line levels and back. What is an RS-232 transceiver? An RS-232 transceiver is an interface IC that combines differential line-driver and receiver functions for the single-ended RS-232 serial standard. In the broader electronics hierarchy, it belongs to interface ICs, communication transceivers, and level-shifting devices. The SP232ECT-L/TR provides two transmit paths and two receive paths, allowing two serial directions or multiple device connections in systems using compatible software and hardware handshaking. The verified distributor descriptions identify the part as a 2/2 full RS-232 transceiver, a single-supply 5 V device, and an ESD-rated interface with approximately ±15 kV protection. Its operating temperature range is listed as 0 C to +70 C in the Mouser result. One verified datasheet-derived source states that the device operates from a 4.5 V to 5.5 V supply and uses a 16-SOIC package. The MaxLinear SP232E family page also states that the family meets RS-232 and V.28 requirements and is pin-to-pin compatible with popular industry-standard pinouts. Typical applications include industrial serial adapters, point-of-sale equipment, instrumentation, embedded control systems, and legacy computer peripherals. Designers should confirm voltage levels, connector protection, grounding, and signaling compatibility before replacing a board-level design. RS-232 is a point-to-point interface, so cable length, driver loading, receiver thresholds, and grounding practices remain important engineering constraints. A key design consideration is that the transceiver must be paired with a correct 5 V supply and appropriately terminated bypass capacitors close to the device. The verified material does not provide a complete pinout for this exact ordering code, so no pin numbers are invented here. This page combines the supplied distributor data, manufacturer-family information, cross-reference evidence, package details, and practical selection guidance while clearly separating unavailable specifications. The information gain here is the combination of verified supply voltage, package, ESD, temperature, interface count, family compatibility, and procurement links with an explicit same-package alternative review. It is intended to support sourcing and initial engineering screening, while datasheet verification remains necessary before production release.

Devis Contact
SP232EEN-L - 2/2 RS-232 Transceiver, 5V, 16-SOIC
SP232EEN-L

SP232EEN-L - 2/2 RS-232 Transceiver, 5V, 16-SOIC

The MaxLinear SP232EEN-L is a 2/2 full-duplex RS-232 line transceiver operating from a single 5 V supply in a 16-SOIC package. It provides two drivers and two receivers for RS-232 and V.28 serial-interface designs, with verified distributor data identifying a 4.5 V to 5.5 V supply range, 240 kbps data rate, 500 mV receiver hysteresis, and a -40C to +85C operating-temperature range. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 line signals and converts received line signals back into digital logic. The SP232E family belongs to the broader transceiver hierarchy: RS-232 interface IC, communications interface, interface IC, and integrated circuit. Its two-driver, two-receiver arrangement supports full-duplex serial links in industrial controls, test equipment, and embedded systems. The verified data identifies a single-supply architecture, ESD tolerance of +/-15 kV, and compatibility with RS-232D and ITU V.28 protocols. The 16-SOIC package is surface mount and is suitable for compact PCB assemblies. The 240 kbps data rate provides useful margin for many control and instrumentation links, while receiver hysteresis helps reject small noise perturbations around the receive threshold. Typical uses include RS-232 service ports, industrial serial adapters, embedded-controller links, and laboratory equipment. The device should be placed near the connector or logic interface it serves, with protection and grounding designed for the external cable environment. Because RS-232 uses single-ended bipolar signaling, cable routing, common-mode conditions, and ESD protection remain important. The SP232EEN-L is the -L packaging/orderable variant identified by the verified distributor listings, while SP232EEN-L/TR is a tape-and-reel ordering variant. Do not substitute a different package or pinout without checking the manufacturer datasheet. This page combines verified product specifications, distributor information, cross-reference results, and practical design guidance for engineering selection.

Devis Contact
SP232EEN-L/TR - 2/2 RS-232 Transceiver, 5V, 16-SOIC (Tape & Reel)
SP232EEN-L/TR

SP232EEN-L/TR - 2/2 RS-232 Transceiver, 5V, 16-SOIC (Tape & Reel)

The MaxLinear SP232EEN-L/TR is a 2/2 full-duplex RS-232 line transceiver operating from a single 5 V supply in a 16-SOIC package. It provides two drivers and two receivers for RS-232 and V.28 serial-interface designs, with verified distributor data identifying a 4.5 V to 5.5 V supply range, 240 kbps data rate, 500 mV receiver hysteresis, and a -40C to +85C operating-temperature range. An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 line signals and converts received line signals back into digital logic. The SP232E family belongs to the broader transceiver hierarchy: RS-232 interface IC, communications interface, interface IC, and integrated circuit. Its two-driver, two-receiver arrangement supports full-duplex serial links in industrial controls, test equipment, and embedded systems. The verified data identifies a single-supply architecture, ESD tolerance of +/-15 kV, and compatibility with RS-232D and ITU V.28 protocols. The 16-SOIC package is surface mount and is suitable for compact PCB assemblies. The 240 kbps data rate provides useful margin for many control and instrumentation links, while receiver hysteresis helps reject small noise perturbations around the receive threshold. Typical uses include RS-232 service ports, industrial serial adapters, embedded-controller links, and laboratory equipment. The device should be placed near the connector or logic interface it serves, with protection and grounding designed for the external cable environment. Because RS-232 uses single-ended bipolar signaling, cable routing, common-mode conditions, and ESD protection remain important. The SP232EEN-L/TR is the -L packaging/orderable variant identified by the verified distributor listings, while SP232EEN-L/TR/TR is a tape-and-reel ordering variant. Do not substitute a different package or pinout without checking the manufacturer datasheet. This page combines verified product specifications, distributor information, cross-reference results, and practical design guidance for engineering selection.

Devis Contact
SP232EEP-L - 120kbps ±15kV RS-232 Transceiver | MaxLinear
SP232EEP-L

SP232EEP-L - 120kbps ±15kV RS-232 Transceiver | MaxLinear

MaxLinear SP232EEP-L is a 2/2 full-duplex RS-232 line-driver and receiver interface IC with a 4.5V to 5.5V single-supply range, 120kbps data rate, and ±15kV ESD protection in a 16-pin PDIP package. It is designed for equipment requiring two RS-232 transmit channels and two receive channels while meeting RS-232 and V.28 protocol requirements. An RS-232 transceiver is an interface IC that converts logic-level UART signals into differential, bipolar RS-232 line signals and converts received RS-232 signals back into CMOS-compatible digital levels. Within the broader hierarchy, an RS-232 transceiver is a serial-interface IC, an interface IC, and ultimately a semiconductor designed to connect data-processing equipment to a wired communications port. The SP232EEP-L combines the driver and receiver functions in one package while requiring external charge-pump capacitors. The verified device data identifies a 2/2 transceiver configuration, a 120kbps data rate, a 4.5V to 5.5V supply range, and operation from -40°C to +85°C. Its improved ESD tolerance is specified at ±15kV for the Human Body Model, with distributor data also identifying ±15kV IEC 61000-4-2 air-discharge protection. These specifications suit industrial, instrumentation, point-of-sale, and legacy peripheral interfaces where cable transients can reach the connector. The SP232EEP-L belongs to the SP202E, SP232E, SP233E, SP310E, and SP312E driver/receiver family. Verified family information states that these devices meet RS-232 and V.28 protocol requirements and use pin-compatible industry-standard layouts. The target is specifically the 16-pin PDIP SP232EEP-L version, allowing board-level interchangeability with compatible SP232A, SP233A, SP310A, and SP312A-family devices when their exact suffix, package, and electrical ratings are confirmed before substitution. Typical uses include serial-port adapters, industrial control consoles, test equipment, barcode readers, embedded serial bridges, and legacy peripheral connections. Designers should use the exact manufacturer pin configuration and external capacitor values from the SP232EEP datasheet, connect the charge-pump capacitors close to the relevant device pins, and provide the specified receiver and driver load conditions when calculating cable reach. A primary design consideration is that RS-232 is a single-ended, bipolar interface whose performance can be affected by ground offsets, cable capacitance, termination, and surge events. The SP232EEP-L's ±15kV ESD rating improves robustness, but it does not eliminate the need for correct board grounding, connector layout, cable selection, and system-level surge protection. Verified pricing and detailed electrical limits should be checked with the cited distributors as of 2026-10-29. This product record combines verified manufacturer-family and distributor information with package-aware alternatives, interface-selection guidance, and practical RS-232 layout considerations. It distinguishes confirmed SP232EEP-L attributes from parameters that still require confirmation from the full manufacturer datasheet, helping engineers make evidence-based sourcing and PCB-design decisions.

Devis Contact
SP232EET-L - 5V RS-232 Transceiver | MaxLinear (Tape & Reel)
SP232EET-L

SP232EET-L - 5V RS-232 Transceiver | MaxLinear (Tape & Reel)

MaxLinear, Inc. SP232EET-L is a 5 V single-supply RS-232 line transceiver with two drivers and two receivers in a 16-pin SOIC package. It provides ±15 kV Human Body Model ESD tolerance, operates from 4.5 V to 5.5 V, and is specified over the -40°C to +85°C temperature range. The device converts logic-level digital signals into RS-232 line levels and receives differential bipolar RS-232 signals for conversion to CMOS-compatible logic levels. An RS-232 transceiver is an interface IC that bridges a host controller or peripheral using single-ended CMOS logic with equipment connected through the RS-232 serial standard. Within the interface hierarchy, the SP232EET-L belongs to the RS-232 driver/receiver family, combines a line transmitter with a line receiver, and ultimately supports serial communication between electronic systems. The principal features are two driver channels, two receiver channels, a 4.5 V to 5.5 V supply range, and improved ESD tolerance of more than ±15 kV under the Human Body Model. Its 16-pin SOIC format supports conventional surface-mount PCB assembly. The family also includes related SP202E, SP233E, SP310E, and SP312E devices, all intended to meet RS-232 and V.28 serial protocol requirements. The SP232EET-L is compatible with the standard pin arrangement used by established RS-232 interface implementations. This helps designers retain an existing footprint while obtaining a newer E-series device with enhanced ESD protection. The operating range of 4.5 V to 5.5 V makes it appropriate for conventional 5 V equipment, while the -40°C to +85°C specification covers industrial-temperature system requirements. Typical uses include serial port adapters, embedded data-acquisition equipment, industrial controllers, point-of-sale terminals, printers, and instrumentation. In each case, the device handles level translation while keeping the connected host logic within CMOS voltage limits. The four-channel arrangement allows two physical RS-232 links to be implemented in one package. Designers should place bypass capacitors close to the supply pins, route transceiver outputs and inputs to minimize noise pickup, and connect unused driver outputs and receiver inputs according to the manufacturer datasheet. Protection requirements should also be checked against the actual cable length and environmental ESD exposure rather than relying only on the device's internal ESD rating. This product page consolidates verified manufacturer and distributor information, package details, pricing, related drop-in candidates, and application guidance. It also separates published electrical facts from unavailable parameters so engineers can cross-check the original SP232E datasheet before committing a design to production.

Devis Contact
SP232EET-L/TR - 5V RS-232 Transceiver | MaxLinear
SP232EET-L/TR

SP232EET-L/TR - 5V RS-232 Transceiver | MaxLinear

MaxLinear, Inc. SP232EET-L/TR is a 5 V single-supply RS-232 line transceiver with two drivers and two receivers in a 16-pin SOIC package. It provides ±15 kV Human Body Model ESD tolerance, operates from 4.5 V to 5.5 V, and is specified over the -40°C to +85°C temperature range. The device converts logic-level digital signals into RS-232 line levels and receives differential bipolar RS-232 signals for conversion to CMOS-compatible logic levels. An RS-232 transceiver is an interface IC that bridges a host controller or peripheral using single-ended CMOS logic with equipment connected through the RS-232 serial standard. Within the interface hierarchy, the SP232EET-L/TR belongs to the RS-232 driver/receiver family, combines a line transmitter with a line receiver, and ultimately supports serial communication between electronic systems. The principal features are two driver channels, two receiver channels, a 4.5 V to 5.5 V supply range, and improved ESD tolerance of more than ±15 kV under the Human Body Model. Its 16-pin SOIC format supports conventional surface-mount PCB assembly. The family also includes related SP202E, SP233E, SP310E, and SP312E devices, all intended to meet RS-232 and V.28 serial protocol requirements. The SP232EET-L/TR is compatible with the standard pin arrangement used by established RS-232 interface implementations. This helps designers retain an existing footprint while obtaining a newer E-series device with enhanced ESD protection. The operating range of 4.5 V to 5.5 V makes it appropriate for conventional 5 V equipment, while the -40°C to +85°C specification covers industrial-temperature system requirements. Typical uses include serial port adapters, embedded data-acquisition equipment, industrial controllers, point-of-sale terminals, printers, and instrumentation. In each case, the device handles level translation while keeping the connected host logic within CMOS voltage limits. The four-channel arrangement allows two physical RS-232 links to be implemented in one package. Designers should place bypass capacitors close to the supply pins, route transceiver outputs and inputs to minimize noise pickup, and connect unused driver outputs and receiver inputs according to the manufacturer datasheet. Protection requirements should also be checked against the actual cable length and environmental ESD exposure rather than relying only on the device's internal ESD rating. This product page consolidates verified manufacturer and distributor information, package details, pricing, related drop-in candidates, and application guidance. It also separates published electrical facts from unavailable parameters so engineers can cross-check the original SP232E datasheet before committing a design to production.

Devis Contact
SP3222EBEY-L/TR - 3V-5.5V RS-232 2-DRV/2-RCV Transceiver | MaxLinear
SP3222EBEY-L/TR

SP3222EBEY-L/TR - 3V-5.5V RS-232 2-DRV/2-RCV Transceiver | MaxLinear

The MaxLinear SP3222EBEY-L/TR is a 3.0V to 5.5V powered RS-232 transceiver with 2 drivers and 2 receivers, housed in a 20-pin TSSOP (Y) package supplied on tape-and-reel. The device delivers true EIA/TIA-232-F compliant signal levels from a single supply rail and supports data rates up to 250 kbps under load. An integrated high-efficiency charge pump requires only four 0.1 µF external capacitors in 3.3V operation, minimizing board area and BOM cost. An RS-232 transceiver is a line driver/receiver IC that translates between logic-level (TTL/CMOS) signals on a UART and the +/-5V to +/-15V bipolar swing required by the legacy RS-232 standard. Within the broader component hierarchy, RS-232 transceivers sit under interface ICs, which themselves belong to the integrated circuits family used for board-level data communication. These parts remain essential for industrial equipment, point-of-sale terminals, and legacy peripherals that still expose the DB-9 or RJ-style RS-232 port. Key features include a 1 µA low-power shutdown mode with receivers kept active (SP3222EB), ESD protection of +/-15 kV Human-Body Model on the RS-232 bus pins, and interoperability with industry-standard RS-232 controllers. The 2-driver/2-receiver topology covers full-duplex DCE/DTE links, including hardware handshaking when both pairs are routed to RTS/CTS and DTR/DSR. The TSSOP-20 footprint and 4.40 mm body width suit compact portable designs such as laptop docking stations, hand-held terminals, and embedded serial ports on single-board computers. Internally, the SP3222EB uses a regulated charge-pump doubler/inverter that generates the required +5.5V and -5.5V drivers from a single 3.0V to 5.5V supply, eliminating the historical need for a +/-12V rail. Receivers operate from the main 3.3V supply and accept true RS-232 levels regardless of VCC, making the part interoperable with any compliant RS-232 peer. Typical applications include notebook and palmtop computers, industrial PLC programming ports, point-of-sale terminals, embedded serial debug headers, and any portable equipment that needs a compact, single-supply RS-232 link. Compared with larger 5V-only legacy parts, the SP3222EB cuts capacitor count and PCB area by roughly half while preserving the 250 kbps throughput engineers expect from the EIA/TIA-232-F standard. When designing with this device, place the four 0.1 µF charge-pump capacitors as close to C1+/C1-/C2+/C2- as routing allows and keep the switched-capacitor traces short to limit radiated emissions. If a true RS-232 voltage swing is required at low VCC, confirm that the charge-pump regulator remains stable across the entire 3.0V to 5.5V input range. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, giving buyers and design engineers a single reference for sourcing and applying the SP3222EBEY-L/TR.

Devis Contact
SP3222ECT-L/TR - 3V-5.5V RS-232 2-Driver/2-Receiver Transceiver | MaxLinear
SP3222ECT-L/TR

SP3222ECT-L/TR - 3V-5.5V RS-232 2-Driver/2-Receiver Transceiver | MaxLinear

The MaxLinear SP3222ECT-L/TR is a 2-driver / 2-receiver RS-232 transceiver IC operating from a single 3V to 5.5V supply, housed in an 18-pin SOIC (7.50 mm width) package and shipped on Tape & Reel. The part meets true EIA/TIA-232-F standards, supports a minimum 120 kbps data rate under full load, and offers a 1 µA low-power shutdown mode with receivers remaining active for external device monitoring. According to the MaxLinear SP3222E/SP3232E datasheet, the integrated high-efficiency charge-pump requires only 0.1 µF capacitors in 3.3V operation. An RS-232 transceiver is a type of serial communication interface IC that converts logic-level UART signals (typically 0V/3.3V or 0V/5V CMOS/TTL) to the higher bipolar ±5V to ±15V signaling levels required by the legacy EIA/TIA-232 standard. Within the broader hierarchy, RS-232 transceivers belong to the line driver/receiver family, which itself sits under interface ICs in the power management and connectivity ecosystem. They are essential for bridging modern microcontrollers with industrial PCs, point-of-sale terminals, legacy peripherals, and serial debug ports. Key features include true EIA/TIA-232-F compliance from a 3.0V to 5.5V rail, an enhanced ESD protection rating on the RS-232 pins, 1 µA shutdown current with receiver wake-up, and integrated charge-pump DC-DC converters that eliminate the need for a separate ±12V supply. The 18-SOIC wide-body package supports standard 300-mil PCB footprints and provides robust thermal performance for industrial environments. Operating temperature range is 0°C to +70°C for the commercial-grade 'ECT' suffix variant. The architecture pairs an on-chip charge pump with a proprietary low-dropout transmitter topology and a logic-side receiver with hysteresis, ensuring noise-immune reception in electrically noisy industrial cabinets. The high-efficiency charge pump uses only four small 0.1 µF capacitors and produces ±5.5V rails from a 3.3V input, allowing true RS-232 swing without external DC-DC converters. Typical applications include notebook and palmtop computers, industrial control PLC serial ports, point-of-sale (POS) terminals, battery-powered handheld instruments, and any design that needs true RS-232 levels from a single low-voltage logic supply. When designing with this part, keep in mind that the shutdown pin (/SHDN) must be driven high for normal operation and pulled low only when battery life is critical. Decoupling the charge-pump capacitors with short, low-ESR traces directly at pins C1+, C1-, C2+, and V- minimizes output ripple. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not found in the standalone manufacturer datasheet, giving purchasing and engineering teams a single source for cross-functional decision-making.

Devis Contact
SP3223EUCY-L - +3.0V to +5.5V RS-232 Transceiver | MaxLinear
SP3223EUCY-L

SP3223EUCY-L - +3.0V to +5.5V RS-232 Transceiver | MaxLinear

The MaxLinear SP3223EUCY-L is an intelligent +3.0V to +5.5V RS-232 transceiver housed in a 20-pin TSSOP package, providing two drivers and two receivers (2/2) for full-duplex RS-232 communication. Key specifications include a guaranteed data rate of 1000 kbps, supply current of 0.3 mA typical, and an integrated high-efficiency charge-pump that requires only 0.1 µF capacitors for 3.3V operation. The device is designed for portable applications such as notebook computers and handheld terminals where board space and power efficiency are critical. What is an RS-232 transceiver? An RS-232 transceiver is an interface IC that converts logic-level UART signals (typically 0V/3.3V or 0V/5V CMOS/TTL) into the bipolar ±5V to ±15V voltage swings defined by the EIA/TIA-232-F standard, which legacy PCs, industrial controllers, point-of-sale terminals, and instrumentation equipment use for serial communication. Within the broader component taxonomy, RS-232 transceivers sit under Interface ICs, alongside RS-485 transceivers, CAN transceivers, and USB-to-UART bridges. The SP3223EUCY-L delivers compliant RS-232 performance from a single 3.0V to 5.5V supply, interoperates with EIA/TIA-232 down to a 2.7V source, and adheres to EIA/TIA-562 at reduced drive levels. Its AUTO ON-LINE® circuitry automatically wakes the device from shutdown when a valid RS-232 signal is detected on the receiver input, eliminating the need for external activity-detect logic. An enhanced ESD rating of ±15 kV Human Body Model on the driver outputs and receiver inputs provides robust protection against cable-discharge transients in real-world environments. Typical applications include notebook and handheld computer serial ports, industrial PDA cradles, point-of-sale (POS) terminals, battery-powered diagnostic equipment, and any portable embedded system that needs a true RS-232 link without the bulk of a ±12V supply. The 0.1 µF charge-pump capacitors and 20-pin TSSOP footprint allow a complete 2-driver/2-receiver RS-232 port to fit in roughly 30 mm² of board area. The 0°C to +70°C commercial operating range suits indoor enclosures and consumer-grade handhelds; for industrial temperature designs, an 'I' suffix variant (SP3223EUCY-L is the commercial-grade part) is available from the same family. When designing with this part, remember that the 1000 kbps data rate requires the AUTO ON-LINE® wake-up path to settle; if the system depends on sub-millisecond link bring-up after power-down, gate the FORCEON pin externally. Place the four 0.1 µF charge-pump capacitors (C1–C4) within 3 mm of the IC pins to keep switching noise off the analog ground plane. The "-L" suffix indicates the lead-free / RoHS-compliant finish; pair this with a nickel-palladium-gold (NiPdAu) or matte-tin PCB surface finish to prevent solderability issues during reflow. This page synthesizes MaxLinear distributor pricing, drop-in same-package alternatives, and practical charge-pump PCB layout guidance that the bare datasheet does not present in a single place.

Devis Contact