Produits (46 000+)

SN75155D - RS-232 Line Driver/Receiver | Texas Instruments
SN75155D

SN75155D - RS-232 Line Driver/Receiver | Texas Instruments

The Texas Instruments SN75155D is a monolithic full RS-232 line driver and receiver rated for a 15 V supply, packaged in an 8-pin SOIC (D). It meets or exceeds ANSI EIA/TIA-232-E and ITU Recommendation V.28 interface requirements, provides a 10 mA current-limited transmitter output, and operates across a 0 °C to 70 °C temperature range. These characteristics make it suitable for conventional data-terminal and data-communication equipment. An RS-232 line transceiver is an interface IC that converts logic-level signals into voltage levels suitable for serial links while receiving and conditioning remote signals into logic-compatible levels. In the broader semiconductor hierarchy, it belongs to the interface IC class and combines a line driver, a line receiver, and supporting bias or regulation functions within one monolithic package. The response-control input allows a resistor or resistor-and-bias network to be connected to ground for additional receiver noise control. The SN75155D uses current-limited outputs to support RS-232 signaling without the uncontrolled drive current associated with an ideal voltage source. Its integrated low-power design is specified at 130 mW, making it useful in compact equipment where both interface performance and power consumption matter. The device combines one driver and one receiver rather than providing a complete multi-channel RS-232 port. Texas Instruments describes the SN75155 as a monolithic line driver and receiver for the interface between data terminal equipment and data communication equipment. The 8-pin SOIC package supports conventional surface-mount assembly, while the 0 °C to 70 °C range targets commercial-temperature equipment. Exact timing, supply-current, receiver-threshold, and output-level details should be taken from the manufacturer datasheet revision identified by Texas Instruments as Revision C. Typical uses include RS-232 ports for industrial control equipment, data acquisition systems, point-of-sale terminals, legacy serial adapters, and embedded systems that still communicate with RS-232 peripherals. The interface can support host-to-peripheral links where logic levels remain compatible with the SN75155 receiver and where cable length and baud rate satisfy the applicable RS-232 system design limits. When designing the circuit, treat the response-control input as a receiver-tuning element and follow the manufacturer’s resistor or resistor-and-bias connection guidance. Confirm the system ground strategy, add the required interface protection for exposed connectors, and validate signal levels at the far end of the cable rather than relying only on logic-side measurements. This product page combines the device interface role, verified package and commercial-temperature information, manufacturer documentation links, practical RS-232 design guidance, and carefully qualified same-family replacement information. It also distinguishes true electrical alternatives from ordinary reel, tape, or grade-code variants so procurement decisions remain tied to board-level compatibility.

Devis Contact
SN75155P - RS-232 Line Driver and Receiver | Texas Instruments
SN75155P

SN75155P - RS-232 Line Driver and Receiver | Texas Instruments

The Texas Instruments SN75155P is a monolithic full-duplex RS-232 line driver and receiver packaged in an 8-pin PDIP (P) package. It supports the ANSI EIA/TIA-232-E interface between data terminal equipment and data communication equipment and operates across a 0°C to 70°C commercial temperature range. The device combines one driver, one receiver, and a response control input in a single package. An RS-232 interface transceiver is a semiconductor device that converts logic-level signals into RS-232-compatible voltage levels and converts received RS-232 levels back into logic signals. In the interface hierarchy, the SN75155P belongs to the line-driver-and-receiver family, within transceivers, interface ICs, and integrated circuits. It is commonly placed between a host controller or UART and a DB-25 or equivalent RS-232 connector. The key features of the SN75155P are its integrated driver and receiver, full RS-232 operation, response control for receiver-noise adjustment, and an 8-pin PDIP package. The response control input accepts a resistor, or a resistor and bias voltage, connected to ground to control receiver noise behavior. This makes the part useful in legacy data-communication equipment where one receiver serves a console, modem, or data-terminal connection. Internally, the driver converts TTL/CMOS-level inputs into bipolar RS-232 signal levels, while the receiver converts a differential-looking RS-232 input into a logic-level output for the system controller. Because the driver and receiver operate in opposite directions, one SN75155P supports bidirectional communication when the driver output and receiver input are connected to separate interface signals. The manufacturer datasheet is the controlling reference for voltage thresholds, timing, and input-current limits. Typical applications include serial console links, data-terminal equipment, legacy printer interfaces, industrial control panels, and RS-232 test equipment. The SN75155P is also appropriate where a controller requires a receive path with adjustable noise control rather than a modern multi-channel RS-232 transceiver. When laying out an RS-232 design, place the transceiver close to the connector and keep the driver and receiver return paths routed away from sensitive analog inputs. Confirm the interface voltage thresholds, driver slew behavior, and response-control network against the manufacturer datasheet before releasing a production board. This page consolidates the manufacturer product information, package and temperature data, interface standard, application context, and substitution guidance for engineers evaluating the SN75155P in legacy serial-interface designs.

Devis Contact
SN75157D - Dual Differential Line Receiver | Texas Instruments
SN75157D

SN75157D - Dual Differential Line Receiver | Texas Instruments

The Texas Instruments SN75157D is a dual differential line receiver in an 8-pin SOIC package. It receives two differential or single-ended signals and converts each into a TTL-compatible logic output. The device operates from a single 5 V supply, with a documented operating range of 4.75 V to 5.25 V, and supports signaling rates up to 10 Mbit/s. Its inputs are compatible with EIA/TIA-422-B, EIA/TIA-423-B, ITU V.10, and ITU V.11 line-driver outputs. A differential line receiver converts a small voltage difference between two conductors into a logic-level signal while rejecting common-mode noise. In the signal path, the line receiver sits between a remote transmitter and a digital controller, logic gate array, or data-processing system. The SN75157D can accept either a differential input or a single-ended input at each receiver channel, making it useful in industrial control, instrumentation, data acquisition, and legacy communication equipment. The SN75157D uses Schottky circuitry and provides TTL-compatible outputs. According to the manufacturer datasheet, the device is supplied in 8-pin dual-in-line and small-outline versions, with the SN75157D identifying the SOIC-8 package. Its stated operating temperature range is 0 °C to 70 °C, positioning it as a commercial-temperature interface device. The maximum signaling rate is listed as 10 Mbit/s, supporting moderate-speed point-to-point and multidrop data links. The device includes two independent receiver channels, one 5 V power connection, a ground connection, and six signal pins. Differential inputs reduce susceptibility to externally induced noise because the receiver responds primarily to the voltage between the input pair rather than to their shared voltage relative to ground. Published comparison information lists fault protection from -10 V to 15 V for the SN75157D, although the input protection behavior and application limits should be verified against the complete manufacturer datasheet before applying fault voltages to a design. Typical uses include industrial RS-422 and RS-423 links, data acquisition interfaces, telemetry receivers, and test equipment. Because both receiver channels are independent, one SN75157D can recover two signals and reduce component count compared with two single-channel receivers. The logic outputs can connect directly to TTL or CMOS-compatible receiving logic after checking input thresholds and timing requirements. The primary design consideration is signal integrity. Route the differential pair as a closely matched pair, terminate the line according to the selected network topology, and keep the receiver away from high-current switching paths. Do not substitute the SN75157D for a line driver or RS-232 transceiver; the receiver's TTL outputs and differential input architecture support only the corresponding receiver application.

Devis Contact
SN75158D - Dual RS-422 Line Driver | Texas Instruments
SN75158D

SN75158D - Dual RS-422 Line Driver | Texas Instruments

Texas Instruments SN75158D is a dual differential line driver designed for ANSI EIA/TIA-422-B and ITU V.11 balanced-line interfaces, with two transmitters in an 8-pin SOIC package. It operates from a nominal 5 V supply, supports signaling rates up to 10 Mbit/s, and is specified over 0°C to 70°C. Its TTL totem-pole outputs provide high-current drive capability for balanced twisted-pair lines while maintaining a high-impedance output state when disabled. A differential line driver is an interface IC that converts two single-ended logic signals into complementary differential outputs. In the broader hierarchy, it belongs to line drivers, interface transceivers, and data-communication semiconductors. Differential signaling transmits the same information on two conductors, allowing receiver circuitry to reject common-mode noise and improve reliability over longer cable runs compared with single-ended links. Each SN75158D transmitter provides high-current source and sink capability suitable for balanced lines at normal line impedance without excessive power dissipation. The device includes a common enable function, enabling the outputs to enter a high-impedance state when the interface is inactive. Its 8-pin SOIC package supports conventional surface-mount assembly and is a practical choice for legacy industrial, telecommunications, instrumentation, and point-to-point data interfaces. The SN75158 architecture is centered on two independent differential output channels. TTL-compatible totem-pole output stages actively drive one line high while pulling the other low, allowing the differential receiver to recover the intended signal from the voltage between the pair. This arrangement supports full-duplex designs when the receive function is implemented separately and balanced, multidrop point-to-point arrangements when the cable topology and termination strategy meet the interface specifications. Typical uses include RS-422-compatible links between controllers and peripheral equipment, industrial control consoles, test equipment, telecom peripherals, and legacy instrumentation systems. Because the SN75158 is a driver rather than a complete transceiver, a separate receiver such as the SN75157 family member is required when the same endpoint must both transmit and receive. The operating temperature and 5 V supply requirements make the part especially suitable for conventional commercial equipment rather than automotive or extended-temperature systems. PCB design should preserve the balanced geometry of each differential pair and provide a continuous ground reference beneath the cable when practical. Keep the complementary outputs routed with matched impedance and avoid adding excessive stub lengths. Confirm the receiver, cable length, connector pinout, enable polarity, and termination arrangement against the complete system interface before releasing a layout. This product page combines the manufacturer's interface description with practical guidance on application fit, PCB implementation, qualification questions, and same-package alternatives. It also identifies which functions remain outside the transmitter-only device, helping engineers determine whether SN75158D is appropriate before beginning a board-level design.

Devis Contact
SN75159N - Dual RS-422/485 Driver | Texas Instruments
SN75159N

SN75159N - Dual RS-422/485 Driver | Texas Instruments

Texas Instruments SN75159N is a dual differential RS-422/RS-485 line-driver interface IC with two independently controlled outputs, 3-state operation, and a 14-pin PDIP package. It operates from a single 5 V supply and provides TTL-compatible balanced line operation for industrial data links. Each driver includes an individual output control, allowing its associated outputs to enter a high-impedance state for party-line or shared-bus arrangements. A differential line driver is an interface IC that converts logic-level signals into balanced differential outputs suitable for reliable, noise-resistant communication over cables. The SN75159 belongs to the RS-422 driver family within the broader interface-IC and bus-transceiver hierarchy. Its differential outputs help reject common-mode noise, while the 3-state capability prevents an inactive driver from loading a shared bus. The device provides two differential driver channels, single 5 V operation, TTL-compatible inputs, and independent controls for each channel. When its output-control input is low, the corresponding output pair becomes high-impedance and can neither drive nor load the bus. This behavior supports multiple transmitters sharing a party-line bus when only one driver is intended to be active at a time. The manufacturer identifies the SN75159 as meeting or exceeding ANSI EIA/TIA-422-B and ITU Recommendation V.11 requirements. The SN75159 is a driver rather than a full transceiver: it does not include receiver channels for returning data from the bus. Its 14-pin PDIP construction is appropriate for through-hole industrial, control, instrumentation, and legacy communication equipment where socketed or manually assembled DIP packaging is preferred. Because each channel can be disabled independently, the device can support multiple physical drivers on one bus when their active intervals are properly coordinated. Typical uses include industrial automation links, RS-422 point-to-point links, multidrop party-line systems, test equipment, process-control instrumentation, and data acquisition systems requiring balanced differential signaling. The 5 V supply and TTL-compatible control interface simplify connection to older logic systems, while independent channel control supports bus segmentation or spare-driver arrangements. The primary design consideration is ensuring that only one transmitter actively drives a shared bus at a time. Output-enable timing, grounding, cable termination, and driver-output loading must be evaluated together. The differential outputs should connect to the intended RS-422 network using an appropriate cable and termination scheme; the manufacturer datasheet should be consulted for the complete electrical limits and pin assignments. This page organizes the SN75159N interface function, verified operating characteristics, practical use cases, and design cautions into an engineering-focused guide. It also separates confirmed product information from parameters that require direct confirmation with the manufacturer before schematic release or production procurement.

Devis Contact
SN75172N - 4-Channel RS-485 Driver | Texas Instruments
SN75172N

SN75172N - 4-Channel RS-485 Driver | Texas Instruments

Texas Instruments SN75172N is a monolithic quadruple differential line driver with four 3-state outputs, a 4.75 V to 5.25 V supply range, and operation at rates up to 4 megabaud. The device is packaged in a 16-pin PDIP and is designed for balanced multipoint transmission on long bus lines in noisy environments. Its four channels support RS-422, RS-485, EIA/TIA-422-B, and ITU-T V.11-compatible interfaces. A differential line driver is a type of interface transceiver component that converts a digital logic signal into a balanced differential output. It belongs to the interface IC hierarchy, where line drivers are used with line receivers to form robust communications links over cables or backplanes. Balanced signaling reduces susceptibility to common-mode interference, while 3-state outputs allow multiple devices to share a bus when they are not actively transmitting. The SN75172 provides four independent differential driver channels in one package. Each channel can be placed in a high-impedance state to permit party-line operation, and the wide positive and negative common-mode output voltage ranges support noisy multipoint networks. Operation up to 4 megabaud makes the device suitable for industrial control, instrumentation, communications, and data-acquisition systems using balanced differential buses. Technically, each driver translates complementary TTL-compatible input states into a differential output. The true differential outputs support current-mode signaling, while the three-state outputs provide bus-enable control without requiring a separate bus driver. Because the SN75172N is a driver-only device, a receiving node requires a compatible differential receiver or transceiver elsewhere in the system. Typical implementations include four isolated or non-isolated RS-485 transmitters, factory automation links, test and measurement equipment, industrial peripheral interfaces, and point-to-point RS-422 links. In each case, the system must preserve the differential pair routing, provide a correctly sized termination strategy, and account for common-mode voltage at the cable interface. A key design consideration is that the SN75172N is intended for a 4.75 V to 5.25 V supply and does not provide galvanic isolation. Designers should use a suitable regulated supply, route each differential pair as a tightly coupled pair, and protect exposed bus connectors as required by the installation environment. Enable polarity and timing should be checked against the system requirement before sharing a party-line bus. This page organizes the manufacturer's principal electrical and interface characteristics with design guidance, application context, package information, and replacement guidance. It also distinguishes driver-only devices from combined transceivers and receivers so that board-level replacements are evaluated for actual pin and functional compatibility rather than broad RS-485 similarity.

Devis Contact
SN75174N - 4-Channel 4 MBd RS-485 Driver | Texas Instruments
SN75174N

SN75174N - 4-Channel 4 MBd RS-485 Driver | Texas Instruments

The Texas Instruments SN75174N is a monolithic quadruple differential line driver with four independent 3-state outputs, support for balanced multipoint buses at rates up to 4 megabaud, and operation from a 5 V supply in a 16-pin PDIP package. It is designed to meet ANSI EIA/TIA-422-B, RS-485, and ITU Recommendation V.11 requirements, including wide positive and negative common-mode output voltage ranges for party-line systems operating in noisy environments. A differential line driver is an interface IC that converts a single-ended logic signal into two complementary, balanced outputs. In the broader semiconductor hierarchy, a line driver belongs to interface ICs and communication transceivers, providing the physical signaling layer between digital controllers and wired buses. Its balanced differential output reduces sensitivity to common-mode noise and ground-potential differences compared with an unbalanced single-ended driver. The SN75174N integrates four differential drivers, allowing one package to serve four data channels or two bidirectional interfaces when paired with suitable receivers. Every channel has an enable control that can place its differential outputs in a high-impedance 3-state condition. This feature allows several devices to share a bus, supports controlled bus segmentation, and permits external circuitry to establish an idle state. The device supports multipoint architectures without requiring separate single-driver-per-node packages. Its principal verified performance points are four driver channels, a maximum signaling rate of 4 megabaud, 3-state outputs, and compatibility with EIA/TIA-422-B, RS-485, and ITU V.11 requirements. These figures position the part for industrial control, instrumentation, data acquisition, and embedded systems that use balanced copper wiring. The wide output common-mode range is particularly useful in party-line installations where nodes and cables introduce voltage variation. The SN75174N is a driver, not a complete RS-485 transceiver, because it does not include receivers. Systems requiring bidirectional communication should pair it with a suitable receiver or transceiver. Signal integrity depends on controlled-impedance routing, correct pair geometry, termination at the physical endpoints, and common-mode considerations. The data supplied for this record does not include supply-voltage, output-current, propagation-delay, temperature, or absolute-maximum-rating values, so those values remain marked as data needed rather than inferred. This page consolidates the verified manufacturer and distributor records, interface-standard context, application guidance, and replacement limitations in one engineering-oriented reference. Pricing and stock conditions are intentionally not represented as confirmed because the supplied distributor snippets provide availability language but no transaction-specific price table or inventory quantity.

Devis Contact
SN75174NG4 - Quad RS-485 Driver, 4 MBd | Texas Instruments
SN75174NG4

SN75174NG4 - Quad RS-485 Driver, 4 MBd | Texas Instruments

The Texas Instruments SN75174NG4 is a monolithic quadruple differential line-driver IC supporting balanced multipoint bus transmission at rates up to 4 megabaud. The device provides four differential driver channels with 3-state outputs and is packaged as a 16-pin plastic dual in-line package identified as 16-PDIP. A differential line driver is a digital interface component that converts one-sided logic signals into balanced differential outputs. A differential line-driver IC belongs to the broader interface-IC hierarchy, where driver and receiver devices support communication across cables, backplanes, and industrial buses. Balanced signaling improves noise immunity by combining equal-and-opposite signal paths, making this type of driver useful where ground potential differences and coupled noise can affect single-ended links. According to the Texas Instruments SN75174 datasheet, the SN75174 is designed to meet ANSI EIA/TIA-422-B, RS-485, and ITU Recommendation V.11 requirements. Its key operating features include four driver channels, 3-state output capability, operation up to 4 megabaud, and wide positive and negative common-mode output voltage ranges. The wide output range supports party-line bus arrangements in electrically noisy environments. The monolithic implementation provides four differential drivers in one package, reducing the number of separate line-driver packages required for a multi-channel communications interface. The 3-state outputs permit a driver to enter a high-impedance state when it is not actively driving a bus. This feature supports shared-bus architectures and gives system designers control over which connected node participates in transmission. Typical uses include industrial RS-485 equipment, EIA/TIA-422-B balanced data links, multidrop party-line networks, instrumentation interfaces, and communications equipment requiring several differential outputs. Because the device is intended for balanced multipoint transmission, system design should account for cable impedance, termination, grounding, and the electrical behavior of every node connected to the bus. Designers should use the manufacturer pin-description table when assigning PCB tracks and should verify the device's electrical limits and enable-control behavior against the specific system interface. Care is also needed when combining outputs on a shared bus so that multiple 3-state drivers are never enabled simultaneously, as simultaneous active outputs can produce contention. This page combines the manufacturer's device information with practical interface-design guidance, application-fit analysis, and a package-focused comparison framework. It is intended to help engineers identify when the SN75174NG4 belongs in an RS-485 or EIA/TIA-422-B design before beginning board-level implementation.

Devis Contact
SN75175D - Quad RS-485 Receiver, 10 Mbps | Texas Instruments
SN75175D

SN75175D - Quad RS-485 Receiver, 10 Mbps | Texas Instruments

The Texas Instruments SN75175D is a quadruple differential line receiver supporting RS-422, RS-423, and RS-485 balanced multipoint buses at rates up to 10 Mbps. The device provides four differential receiver channels, 50 mV receiver hysteresis, and three-state outputs in a 16-pin SOIC (D) package. Its 4.75 V to 5.25 V supply range and 0°C to 70°C operating-temperature range identify it as a commercial-temperature line-interface component. A differential line receiver belongs to the interface IC hierarchy: it converts small voltage differences between two conductors into a digital logic signal. This conversion allows balanced signaling to reject common-mode noise, reduce ground-reference errors, and improve robustness in industrial environments. The SN75175 family is specifically intended for balanced multipoint data transmission rather than single-ended logic. Each receiver converts its differential input pair to a logic output. The common enable control places the four outputs into a high-impedance state when required, allowing multiple receivers to share a bus without active-output contention. Three-state operation is particularly useful in bus architectures where several nodes may drive a shared line during different operating intervals. The 50 mV hysteresis helps prevent output chatter around the decision threshold. The SN75175D supports a maximum signaling rate of 10 Mbps and uses a single 5 V supply. According to the manufacturer datasheet, the device is designed around EIA-485 and EIA-422A/23A balanced-interface requirements and CCITT recommendations. It contains no transmitters, so each channel is a receiver-only path; an external line driver is required when the design also needs to transmit. Typical uses include industrial RS-485 equipment, data acquisition systems, instrumentation links, computer peripherals, and multipoint communication networks. Because the device supports four channels, one package can serve several independent differential inputs or four nodes on a multidrop bus when the enable function is managed correctly. PCB design should preserve the differential signal path and provide a continuous return reference. Route each differential pair with matched geometry and avoid adding test pads or long branches that disturb impedance. Decouple the 5 V supply close to the device, and verify that the bus topology, termination, protection, and common-mode range match the cable and environmental conditions. This page combines manufacturer specifications, compatible substitute references, interface-selection guidance, package details, and practical implementation notes. It helps engineers determine whether the SN75175D fits a legacy RS-485 or RS-422 design and how to validate a replacement before production release.

Devis Contact
SN75175N - 4-Channel 10 Mbps RS-485 Receiver | Texas Instruments
SN75175N

SN75175N - 4-Channel 10 Mbps RS-485 Receiver | Texas Instruments

Texas Instruments SN75175N is a four-channel differential line receiver with three-state outputs, a 5 V supply range of 4.75 V to 5.25 V, and operation up to 10 Mbps. The device is packaged in a 16-pin plastic DIP and is intended for balanced differential data links using RS-485, RS-422, RS-423, or related receiver interfaces. A differential line receiver is an interface IC that converts two complementary, low-voltage signals into one digital logic signal. In the broader electronics hierarchy, the SN75175N is a line receiver within the interface IC category and specifically belongs to the family of differential bus transceivers. Its differential input arrangement helps reject common-mode noise encountered when a bus cable passes through electrically noisy industrial, communications, or automation environments. The SN75175N integrates four receivers and provides three-state outputs for shared-bus or multi-drop systems. According to the Texas Instruments datasheet, the receiver supports signaling rates up to 10 Mbps and is designed for multipoint bus transmission over long bus lines in noisy environments. These features make it a practical choice when one host must collect data from multiple compatible transmitters over a balanced bus. The 16-PDIP package provides through-hole accessibility for industrial controllers, test equipment, legacy communication systems, and prototype boards. The 4.75 V to 5.25 V operating range supports conventional 5 V digital logic. Because the outputs can enter a high-impedance state, designers can use them in shared-bus architectures, although the complete system must control output enable signals correctly to prevent multiple drivers from simultaneously driving a line. Typical uses include RS-485 industrial monitoring, factory automation equipment, instrumentation, data acquisition systems, and legacy peripheral interfaces. The four independent receiver channels can reduce the number of discrete receiver packages required when a board handles several low-speed or medium-speed differential links. In each case, cable length, topology, termination, grounding, and common-mode limits must be evaluated together because receiver specifications alone do not determine reliable system operation. For a new PCB, place each receiver close to the connector or transceiver interface and keep sensitive differential traces away from switching nodes and high-current paths. Use a common reference-ground strategy appropriate to the connected equipment. For an existing 16-PDIP design, verify every output-enable connection and input threshold against the source device before substituting a functionally similar receiver. This page combines the SN75175N electrical identity, standards-oriented application guidance, package details, drop-in alternatives, and practical bus-design considerations to support faster component selection and PCB integration.

Devis Contact
SN75176 - Differential Bus Transceiver RS-485/RS-422 | Texas Instruments
SN75176

SN75176 - Differential Bus Transceiver RS-485/RS-422 | Texas Instruments

The Texas Instruments SN75176 is a monolithic differential bus transceiver designed for bidirectional data communication on multipoint bus-transmission lines, supporting both RS-422 and RS-485 protocols in an 8-pin PDIP package. It combines a 3-state differential line driver and a 3-state differential line receiver on a single chip, operating over a supply range of 4.75 V to 5.25 V with differential output swings compliant with ANSI TIA/EIA-422-B, TIA/EIA-485-A, ITU V.11, and ITU X.27 standards. The driver delivers ±60 mA maximum output capability, while the receiver features typical input hysteresis of 50 mV for robust noise rejection on long bus lines. What is a differential bus transceiver? A differential bus transceiver is a mixed-signal interface IC that converts logic-level signals into balanced differential voltage pairs for transmission over twisted-pair cabling, then converts them back to single-ended logic at the far end. Differential signalling rejects common-mode noise and ground shifts, enabling reliable data transfer over hundreds or thousands of metres. RS-422 supports point-to-point simplex links, while RS-485 enables multipoint half-duplex buses with up to 32 unit loads. Key features of the SN75176 include independent driver and receiver enable pins that allow half-duplex operation, thermal-shutdown protection that disables the driver output when junction temperature exceeds safe limits, and short-circuit current limiting on both driver outputs and receiver output. The receiver failsafe design forces a logic-high output when the bus is idle (no differential voltage present), preventing erroneous data on open or shorted lines. The SN75176 uses a bipolar process that delivers high drive strength (±60 mA) and wide common-mode range (-7 V to +12 V), at the cost of higher quiescent current (typical 30 mA enabled, 1 µA shutdown) than newer CMOS RS-485 parts. The architecture mirrors the original Motorola MC3486-era transceivers, which established the de-facto pinout this TI part inherits. Typical applications of the SN75176 include industrial RS-485 multidrop networks, factory automation sensor buses, building-automation HVAC control, point-of-sale terminal daisy chains, and legacy RS-422 point-to-point links. Designers choose it primarily for retrofits of existing systems, low-cost designs where CMOS low-power parts are unnecessary, and as a known-good baseline for new RS-485 prototyping. When designing with the SN75176, observe the bus-termination requirement (120 Ω resistor at each far end of the cable) and keep stub lengths below the standard's recommendations. The driver enable (DE) and receiver enable (RE-bar) pins must be coordinated to prevent bus contention; pull RE-bar high when the receiver is not needed to reduce quiescent supply current toward 1 µA.

Devis Contact
SN75176AP - 5V RS-422/RS-485 Transceiver | Texas Instruments
SN75176AP

SN75176AP - 5V RS-422/RS-485 Transceiver | Texas Instruments

The Texas Instruments SN75176AP is a 5 V differential bus transceiver with one driver and one receiver, half-duplex operation, and three-state driver and receiver outputs in an 8-pin PDIP package. Designed for balanced transmission lines, the device supports bidirectional communication over multipoint bus networks and meets ANSI EIA/TIA-422-B and ITU Recommendation V.11 requirements. The SN75176AP is commonly associated with RS-422 and RS-485 interface applications. A differential bus transceiver is an interface IC that converts logic-level signals into balanced differential bus signals and reconstructs logic data from received differential signals. The differential architecture helps reject common-mode noise, while the balanced line supports reliable data transmission through electrically noisy industrial environments. In the signal-chain hierarchy, the SN75176AP is a bus transceiver, belonging to the interface-IC and communications-semiconductor categories. The principal features include one differential driver, one differential receiver, three-state output control, and operation from a single 5 V supply. The driver and receiver enable inputs permit a half-duplex node to disable its driver while monitoring the bus, reducing contention on multipoint networks. The receiver can remain enabled during transmission when the system requires continuous bus monitoring, although the selected logic levels must be verified against the complete system design. The monolithic bidirectional architecture combines transmitter and receiver functions on the same two-wire differential bus. This makes the SN75176AP appropriate for equipment distributed along RS-422 or RS-485 links, including industrial controllers, data-acquisition equipment, building controls, and communication adapters. Its balanced bus interface reduces sensitivity to ground-potential differences and externally coupled noise when the cable, termination, grounding, and transceiver implementation are designed correctly. The 8-pin PDIP package supports conventional through-hole PCB assembly and straightforward inspection or rework. Logic-side pins include driver input, driver enable, receiver enable, and receiver output, while bus-side connections use the A and B differential terminals. A common ground reference is still required between communicating nodes because differential signaling suppresses common-mode noise rather than eliminating the need for a common reference. The principal design consideration is bus configuration. Add proper termination at the physical ends of the bus, use twisted-pair cabling, avoid excessive stub lengths, and ensure only one driver actively drives the bus at a time. The SN75176AP is intended for balanced transmission lines; system designers must also evaluate biasing, protection, grounding, and protocol timing when using it in practical RS-485 networks. This page combines verified manufacturer and distributor references with package, application, design, and selection guidance. It also distinguishes genuine same-footprint drop-in options from broader functional alternatives so engineers can make a PCB-compatible replacement decision rather than treating electrical similarity as proof of interchangeability.

Devis Contact
SN75176BD - 8-Pin RS-485/RS-422 Transceiver | TI (Tape & Reel)
SN75176BD

SN75176BD - 8-Pin RS-485/RS-422 Transceiver | TI (Tape & Reel)

The Texas Instruments SN75176BD is a 5 V differential bus transceiver with an 8-pin SOIC (D) package, designed for bidirectional RS-485 and RS-422 communication over noisy multipoint bus lines. The verified manufacturer listing identifies the device as a differential bus transceiver with 8 pins and a 0 to 70 temperature range. Its differential bus architecture supports balanced transmission, while the three-state driver and receiver functions provide the interface required by industrial communication equipment. A differential bus transceiver is an interface IC that combines a differential line driver and a differential receiver into one package. In an RS-485 or RS-422 system, this transceiver connects a host controller or programmable logic device to a balanced cable network. The driver converts a single-ended logic signal into differential signals, and the receiver converts the differential pair back into a logic signal. This structure belongs to the interface-IC hierarchy and helps improve noise immunity in industrial environments. The verified description states that SN75176BD meets or exceeds ANSI TIA/EIA-422-B and TIA/EIA-485-A requirements and ITU V.11 and X.27 recommendations. It is intended for multipoint transmission on long bus lines in noisy environments. The part is suitable when a system needs bidirectional data communication, balanced transmission lines, and a compact 8-pin surface-mount implementation. The exact electrical limits and timing values must be confirmed from the manufacturer datasheet before final design release. Typical uses include industrial automation equipment, remote I/O, instrumentation, building controls, robotics, and other RS-485 or RS-422 networks. The transceiver can sit between a UART or other controller and a twisted-pair bus. Designers should provide proper decoupling, controlled-impedance routing, grounding, termination, and protection appropriate to the cable length and environment. Bus topology and biasing also depend on the network configuration and should follow the selected standard and system architecture. For PCB implementation, place the transceiver close to the connector or bus header to minimize exposed unbalanced trace length. Route the differential pair together with matched geometry and avoid switching nodes beneath the pair. The 8-pin SOIC package supports conventional surface-mount assembly, while the exact pin assignments and electrical characteristics must be verified against the current TI datasheet before layout or replacement decisions. This page combines the verified manufacturer identification, distributor pricing references, package information, standards references, and practical interface guidance. It distinguishes the SN75176BD from the broader SN75176B family while avoiding unsupported electrical claims where the supplied search data does not provide a verified numeric value.

Devis Contact
SN75176BDR - 8-Pin RS-485/RS-422 Transceiver | TI
SN75176BDR

SN75176BDR - 8-Pin RS-485/RS-422 Transceiver | TI

The Texas Instruments SN75176BDR is a 5 V differential bus transceiver with an 8-pin SOIC (D) package, designed for bidirectional RS-485 and RS-422 communication over noisy multipoint bus lines. The verified manufacturer listing identifies the device as a differential bus transceiver with 8 pins and a 0 to 70 temperature range. Its differential bus architecture supports balanced transmission, while the three-state driver and receiver functions provide the interface required by industrial communication equipment. A differential bus transceiver is an interface IC that combines a differential line driver and a differential receiver into one package. In an RS-485 or RS-422 system, this transceiver connects a host controller or programmable logic device to a balanced cable network. The driver converts a single-ended logic signal into differential signals, and the receiver converts the differential pair back into a logic signal. This structure belongs to the interface-IC hierarchy and helps improve noise immunity in industrial environments. The verified description states that SN75176BDR meets or exceeds ANSI TIA/EIA-422-B and TIA/EIA-485-A requirements and ITU V.11 and X.27 recommendations. It is intended for multipoint transmission on long bus lines in noisy environments. The part is suitable when a system needs bidirectional data communication, balanced transmission lines, and a compact 8-pin surface-mount implementation. The exact electrical limits and timing values must be confirmed from the manufacturer datasheet before final design release. Typical uses include industrial automation equipment, remote I/O, instrumentation, building controls, robotics, and other RS-485 or RS-422 networks. The transceiver can sit between a UART or other controller and a twisted-pair bus. Designers should provide proper decoupling, controlled-impedance routing, grounding, termination, and protection appropriate to the cable length and environment. Bus topology and biasing also depend on the network configuration and should follow the selected standard and system architecture. For PCB implementation, place the transceiver close to the connector or bus header to minimize exposed unbalanced trace length. Route the differential pair together with matched geometry and avoid switching nodes beneath the pair. The 8-pin SOIC package supports conventional surface-mount assembly, while the exact pin assignments and electrical characteristics must be verified against the current TI datasheet before layout or replacement decisions. This page combines the verified manufacturer identification, distributor pricing references, package information, standards references, and practical interface guidance. It distinguishes the SN75176BDR from the broader SN75176B family while avoiding unsupported electrical claims where the supplied search data does not provide a verified numeric value.

Devis Contact
SN75176BP - RS-422/RS-485 Transceiver | Texas Instruments
SN75176BP

SN75176BP - RS-422/RS-485 Transceiver | Texas Instruments

The Texas Instruments SN75176BP is an eight-pin differential bus transceiver for bidirectional RS-422 and RS-485 links, with one driver and one receiver per device and operation from 0°C to 70°C. It is packaged in an 8-pin PDIP package. The verified product information identifies it as a 1/1 transceiver-half interface IC and as a mature differential bus transceiver designed for multipoint transmission on long, noisy bus lines. A differential bus transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and receives those differential signals back into CMOS-compatible logic. RS-422 and RS-485 belong to the interface-transceiver hierarchy, where differential signaling improves noise immunity and allows communication over longer cable runs than ordinary single-ended logic. The SN75176BP combines those functions with three-state driver and receiver outputs for bus management. The verified description states that the device meets the requirements of ANSI TIA/EIA-422-B and TIA/EIA-485-A and ITU Recommendations V.11 and X.27. Its differential bus outputs support multipoint transmission, while the receiver provides a logic-level output for the host controller. The three-state capability allows unused drivers or receivers to be disconnected when multiple nodes share the bus, although exact timing, current, voltage, and node-count details should be confirmed in the manufacturer datasheet before design release. Typical uses include industrial RS-485 links, building automation, instrumentation, factory equipment, and other multidrop networks where long cables and electrically noisy environments are expected. The eight-pin PDIP package is useful for through-hole prototypes, legacy equipment, and serviceable industrial hardware. The device is identified as operating from 0°C to 70°C in the verified Texas Instruments part information; automotive or extended-temperature designs require a separately qualified part. When laying out a board, keep the transceiver pins, connector, cable interface, and grounding arrangement consistent with the differential-bus topology. A transceiver replacement is only acceptable when its package, pin functions, supply requirements, logic levels, driver and receiver electrical limits, and bus-standard behavior have been verified. Do not infer those values from the family name alone. This page combines the verified manufacturer and distributor descriptions with explicit engineering limits where numerical source data was not supplied.

Devis Contact
SN75176BPS - RS-422/RS-485 Transceiver | Texas Instruments
SN75176BPS

SN75176BPS - RS-422/RS-485 Transceiver | Texas Instruments

The Texas Instruments SN75176BPS is a single-channel differential bus transceiver supporting RS-422 and RS-485 communications in an 8-pin SOIC package. It combines one 3-state differential line driver with one differential receiver, operates from a 4.75 V to 5.25 V supply, and is intended for bidirectional data communication over balanced multipoint transmission lines. Its differential signaling and 3-state driver output are suited to industrial, telecommunications, instrumentation, and data-acquisition systems operating in electrically noisy environments. A differential bus transceiver is an interface IC that translates logic-level signals between a host controller and a balanced RS-422 or RS-485 bus. The SN75176BPS belongs to the broader transceiver hierarchy of interface ICs, communication ICs, and semiconductors. Differential signaling reduces susceptibility to common-mode noise because the receiver evaluates the voltage difference between two conductors rather than the voltage of either conductor relative to ground. The 3-state output adds a high-impedance condition, allowing multiple drivers to share a bus when only one node transmits at a time. The SN75176B family is designed for multipoint transmission on long bus lines in noisy environments. According to the Texas Instruments manufacturer datasheet, the devices meet ANSI TIA/EIA-422-B and TIA/EIA-485-A requirements and ITU Recommendations V.11 and X.27. The SN75176BPS combines these balanced-line capabilities with an 8-pin SOIC package suitable for conventional surface-mount PCB assembly. Its one-driver, one-receiver arrangement supports half-duplex RS-485 nodes when the driver enable and receiver enable functions are controlled appropriately. The 3-state driver can be disabled to release the bus, while the receiver provides differential data detection for the receiving function. This architecture supports communication links where multiple transceivers share the same differential pair and arbitration or token passing determines which node drives. Designers must still manage driver enable timing, bus termination, grounding, and protection against transients; the transceiver itself does not eliminate the need for correct bus topology and cable termination. Typical applications include industrial RS-485 control networks, factory automation equipment, building-control systems, instrumentation links, telecommunications equipment, and data-acquisition networks. The SN75176BPS is appropriate when a compact 5 V interface is required for one differential bus channel. A system requiring several independent channels can use multiple SN75176B devices, while modern designs requiring lower unit loading or higher bus-node capacity should evaluate newer TI interface families against system-level requirements. The principal design consideration is bus implementation rather than individual logic compatibility. A correctly terminated network reduces reflections, while grounding and cable routing influence common-mode performance. External protection may be necessary when exposed conductors experience industrial surges. Component selection should account for voltage range, logic levels, temperature grade, package, availability, and the number of nodes sharing the bus rather than relying on the RS-485 label alone. This page consolidates the verified manufacturer description, distributor pricing, pin-compatible alternatives, interface standards, application guidance, and practical PCB considerations into one engineering reference. It also distinguishes confirmed drop-in information from ordering variants and identifies technical data that must be obtained from the manufacturer datasheet before final design release.

Devis Contact
SN75182N - Dual Differential Line Receiver | Texas Instruments
SN75182N

SN75182N - Dual Differential Line Receiver | Texas Instruments

The Texas Instruments SN75182N is a dual differential line receiver designed to detect small differential signals in the presence of large common-mode noise. It provides two receiver channels, TTL-compatible outputs, operation from a single 5 V supply, and a 14-pin PDIP package. The device accepts a common-mode input range of ±15 V and a differential input range of ±15 V, making it suitable for noisy industrial data links and bipolar signaling environments. A differential line receiver is an interface IC that converts the voltage difference between two input terminals into a single-ended logic signal. Its differential input architecture rejects noise shared equally by both signal conductors, while the receiver threshold determines when the differential voltage produces a valid logic state. The SN75182 belongs to the broader line-receiver, interface-IC, and semiconductor hierarchy and is intended for systems where reliable signal recovery is more important than directly processing bipolar signals with digital logic. The SN75182N includes separate channels with individual channel strobes, allowing receiver activity to be controlled when interfacing with shared buses, test equipment, or multi-source systems. Each channel's frequency response can be adjusted with one external capacitor, providing a practical means of balancing signal bandwidth against noise immunity. The device also supports an optional internal line-termination resistor, helping simplify implementations where controlled input impedance and noise reduction are useful. According to the Texas Instruments SN75182 datasheet, TTL-compatible output signals indicate the polarity of the differential input voltage. The 4.5 V to 5.5 V single-supply range places the part in conventional 5 V digital-interface environments. Its two-channel architecture reduces component count when two differential links must be received simultaneously, while the common-mode range provides tolerance for ground offsets and coupled noise encountered in longer industrial or communication links. Typical uses include balanced data acquisition, industrial control links, test and measurement systems, peripheral interfaces, and communications equipment operating with small differential signals over larger common-mode voltages. The receiver is especially relevant where a transmitted differential signal must be recovered reliably before being passed to TTL-compatible logic. PCB implementation should preserve the differential signal path, minimize unequal routing between each input pair, and place the frequency-control capacitor close to its designated device pin. Differential impedance and termination arrangements should be evaluated together because the optional internal termination may change the effective input loading. The manufacturer's pin-description and typical-application information should guide final routing and capacitor selection. This product page combines the SN75182N's verified electrical characteristics with practical interface guidance, package information, sourcing instructions, and a technically qualified replacement assessment. It is intended to help engineers determine whether the receiver's differential sensing, channel-strobe functions, and bandwidth-control features fit a specific signal-chain requirement before beginning layout.

Devis Contact
SN75183D - Dual Differential Line Driver | Texas Instruments
SN75183D

SN75183D - Dual Differential Line Driver | Texas Instruments

The Texas Instruments SN75183D is a dual differential line driver with four high-current outputs, a single 5 V supply, and a 14-pin SOIC package. It is designed to drive balanced lines such as twisted-pair interconnects at normal line impedances while supporting TTL-compatible inputs, short-circuit-protected outputs, and clamp diodes for transient handling. A differential line driver is an interface IC that converts one-sided logic signals into complementary differential outputs. This differential signaling method reduces susceptibility to common-mode noise and supports reliable communication over balanced interconnects. Within the interface hierarchy, the SN75183D belongs to the line-driver class of logic interface ICs, alongside buffers, transceivers, and phase splitters. The SN75183D provides four differential driver outputs arranged as two dual-output channels. Its TTL-compatible inputs allow ordinary TTL logic to control the drivers without additional level conversion. The output stages use high-current, totem-pole-like structures, making the device suitable for phase-splitting, TTL expansion, balanced-line transmission, and systems requiring two complementary outputs from each input. According to the Texas Instruments SN75183 family documentation, the DS8830, SN55183, and SN75183 share the basic differential-driver architecture. The SN75183D is specified for a 0 to 70 °C operating-temperature range and uses a 14-pin SOIC package. These characteristics place it in a legacy interface family where PCB footprint compatibility and established TTL logic compatibility are important design considerations. Typical applications include balanced twisted-pair data links, TTL bus expansion, clock and data phase splitting, industrial control interfaces, retrofits of established TTL systems, and point-to-point links where complementary drive currents improve signal integrity. In each case, the circuit must maintain compatible supply voltage, input logic levels, output loading, and termination requirements. For a new design, check the supply-decoupling arrangement and route the differential pair as a tightly coupled pair. Confirm that the connected line impedance, connector return path, and receiver thresholds match the driver's output characteristics. The short-circuit and clamp features improve robustness, but they do not remove the need for correct board layout and external line protection. This page consolidates the device's electrical characteristics, package information, drop-in family alternatives, application guidance, and practical PCB considerations into a design-focused reference. It also identifies where legacy temperature grade, package variant, and qualification differences matter when maintaining or redesigning an existing circuit.

Devis Contact
SN75185N - 3/5 RS-232 Transceiver, 120 kbit/s | Texas Instruments
SN75185N

SN75185N - 3/5 RS-232 Transceiver, 120 kbit/s | Texas Instruments

The Texas Instruments SN75185N is a single-chip RS-232 interface integrated circuit that combines three line drivers and five line receivers, supporting data rates up to 120 kbit/s in a 20-pin plastic DIP (PDIP-20) package. It meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28 standards for unbalanced serial interfaces and provides ESD protection of 10 kV on the RS-232 pins and 3.5 kV on all other pins under the Human-Body Model. An RS-232 transceiver is a signal-conditioning device that converts logic-level TTL/CMOS signals into the differential voltage levels defined by the RS-232 standard, and converts returning RS-232 levels back into logic levels for the host controller. In the interface hierarchy, the SN75185N sits at the physical-layer boundary between a UART transmitter/receiver inside a microprocessor and the physical DB9 or DB25 serial connector of an IBM PC/AT-class or compatible host. Key features include the asymmetric channel count of three drivers and five receivers, which allows one UART port to share several receive lines or monitor several inputs. The flow-through pinout matches the SN75C185, making board-level interchanges straightforward, and the bipolar process provides the drive current and slew characteristics expected from legacy PC serial ports. Operating voltage is the standard 5 V class, and the device is offered in a through-hole plastic DIP suited to legacy industrial and instrumentation chassis. Technically, the SN75185N integrates multiple SN75188-style bipolar drivers and SN75189-style receivers on one die. Because the receivers are of the threshold type with internal hysteresis, noise immunity at the connector side is high, while the drivers provide the ±5 V to ±15 V swing that RS-232 requires. Data rates of up to 120 kbit/s are adequate for legacy UART traffic, and the combination of three drivers lets a single port support transmit plus two additional output signals such as DTR and RTS if the host software drives them directly. Typical applications include legacy PC/AT serial port interfaces, industrial control panels with DB9 connectors, laboratory and test instrumentation with legacy serial console ports, embedded boards that must talk to older supervisory software, and multi-drop or monitoring arrangements where several status lines are read back from one port. A key design consideration is that the SN75185N is a legacy bipolar part intended for 5 V single-supply operation and through-hole assembly; it is not a modern 3.3 V tolerant design, and it should not be substituted into RS-232 channels running at 3.3 V logic without a level shifter. Plan PCB real estate for a 20-pin DIP footprint if the goal is a drop-in repair of an existing board rather than a new design. This page brings together the manufacturer interface standards, ESD ratings, channel configuration, pin-compatibility notes, and drop-in alternatives for the SN75185N, plus practical design and sourcing guidance that is not consolidated in a single place on the manufacturer datasheet.

Devis Contact
SN75188D - Quadruple RS-232 Line Driver | Texas Instruments
SN75188D

SN75188D - Quadruple RS-232 Line Driver | Texas Instruments

Texas Instruments SN75188D is a monolithic quadruple RS-232 line driver with four driver channels, a 7.5 V to 15 V supply range, and a 14-pin SOIC package. Designed for data-terminal-equipment and data-communications-equipment interfaces, the device conforms to ANSI TIA/EIA-232-E and is designed to interchange with the Motorola MC1488. Each channel uses current limiting, with typical current limiting set at 10 mA. An RS-232 line driver is a differential-interface transmitter that converts TTL or CMOS logic levels into the bipolar voltage swings required by RS-232 links. The SN75188D belongs to the line-driver, interface-IC, and power-management-adjacent signal-interface hierarchy, but its primary function is signal conditioning rather than voltage regulation. It is intended for systems that transmit serial data over longer distances than logic-level interconnects reliably support. The principal features include four independent driver outputs, typical 10 mA output current limiting, power-off output impedance of at least 300 ohms, and slew-rate control through the load capacitor. Current limiting protects the interface when a driver output encounters a fault or improperly terminated cable. The power-off output impedance helps prevent an inactive transmitter from disturbing a connected bus. Each channel requires an external diode in series with its supply-voltage terminal when used in the conventional configuration described by TI. Output transition behavior depends on the capacitive load, so external load capacitance and cable length directly affect signal integrity. The design is based on a monolithic bipolar line-driver architecture rather than a multi-chip discrete implementation. Typical applications include legacy RS-232 ports on industrial controllers, data-logging equipment, test systems, computer peripherals, and instrumentation. The device can also drive four channels toward compatible RS-232 receivers, while modern system designs frequently pair a line driver with a quad line receiver to create complete two-way RS-232 interfaces. For a new layout, place the 14-pin SOIC close to the connector and route each driver trace away from sensitive analog circuitry. Confirm driver polarity, connector pin assignment, external supply-diode orientation, and maximum capacitive loading before releasing the PCB. Use the TI pin-description table when assigning tracks because the exposed logic side and RS-232 output side must not be interchanged. This product page consolidates device specifications, verified source links, replacement context, interface comparisons, and practical RS-232 layout guidance. It helps engineers distinguish the SN75188D from line receivers, full transceivers, and electrically similar but footprint-incompatible alternatives.

Devis Contact
SN75188N - 4x RS-232 Line Driver | Texas Instruments
SN75188N

SN75188N - 4x RS-232 Line Driver | Texas Instruments

The Texas Instruments SN75188N is a monolithic quadruple RS-232 line driver in a through-hole 14-pin plastic DIP package. It provides four driver channels, a 4/0 driver-to-receiver configuration, and operation from dual ±7.5 V to ±15 V supplies. The device is designed to interface data terminal equipment with data communications equipment that conforms to ANSI TIA/EIA-232-E and ITU Recommendation V.28. A quadruple line driver converts TTL or CMOS logic-level signals into balanced, bipolar RS-232 signaling levels. The SN75188N is commonly used when a system needs four transmit channels and does not require a matching receiver inside the same package. Its four independent drivers make it suitable for parallel serial ports, industrial control links, test equipment, multi-channel data acquisition, and legacy computer interfaces. The 14-PDIP format also supports conventional through-hole prototyping and maintenance repairs. Key electrical characteristics include current-limited outputs with approximately 10 mA typical current limiting and a minimum power-off output impedance of 300 ohms. The internal series diodes associated with the supply terminals support bipolar RS-232 operation. Output slew rate is controlled by the load capacitance, allowing transition speed to be matched to the driven cable and receiver network rather than relying on a fixed high-speed edge. The SN75188N operates across the commercial temperature range of 0°C to 70°C. Its through-hole construction and 14-pin DIP outline make it straightforward to install in legacy control systems, but the package requires more PCB area than a surface-mount alternative. Modern mixed-signal designs may choose a surface-mount transceiver or multi-channel interface IC when PCB area, power consumption, or newer logic levels are more important than legacy compatibility. For reliable use, verify the output swing and receiver thresholds against the RS-232 load, keep unused driver outputs terminated in the same manner as active channels, and provide the required bypass capacitance close to each supply pin. Confirm that the connected equipment uses compatible signal polarities and connector pin assignments before replacing a discrete driver network with this monolithic quad driver. This page combines manufacturer device information, RS-232 interface specifications, drop-in cross-reference results, application guidance, and practical implementation notes. It highlights where the SN75188N fits legacy bipolar interfaces, where modern surface-mount transceivers provide a better engineering trade-off, and which compatibility checks matter before substituting the part into an existing circuit.

Devis Contact
SN75189N - Quad RS-232 Line Receiver | Texas Instruments
SN75189N

SN75189N - Quad RS-232 Line Receiver | Texas Instruments

Texas Instruments SN75189N is a quadruple RS-232 line receiver IC with four independent receive channels, a 4.5 V to 5.5 V single-supply range, and a 14-pin PDIP package. Each receiver includes input hysteresis and a response-control terminal that supports threshold shifting or input-noise filtering. Designed for data-terminal and data-communication equipment interfaces, the device targets the receiver side of TIA/EIA-232-F systems. An RS-232 line receiver is an interface-circuit category that converts bipolar serial data signals into logic-level signals for digital equipment. The SN75189N belongs to the broader line-receiver, interface-IC, and semiconductor hierarchy. Its four-channel arrangement allows one package to receive four independent data signals while sharing a common supply and ground. This reduces component count in multi-channel equipment, test systems, industrial controllers, and computer interfaces. Key features include four integrated receivers, a 5 V nominal operating supply, input hysteresis for improved noise immunity, and 7 kΩ input resistance. The response-control function can shift receiver thresholds or introduce input filtering by connecting suitable resistance and capacitance to the CONT terminals. These controls provide flexibility when the received signal levels, cable environment, or system noise conditions differ from standard receiver defaults. The monolithic low-power Schottky implementation combines the four receivers in one package while retaining separate response-control inputs. The input signal range is specified as 30 V, which accommodates the voltage excursions associated with RS-232 signaling. A 7 kΩ input resistance limits loading on the transmitting side, while the receiver logic output provides a convenient interface to TTL or CMOS equipment. Typical applications include multi-channel RS-232 data acquisition, industrial serial-port equipment, test and measurement systems, terminal interfaces, and embedded controllers requiring more than one receive function. Using four receivers in one package simplifies routing and reduces the number of interface ICs, but the system designer must still account for correct signal grounding, cable transients, unused-channel handling, and adequate supply bypassing. For PCB implementation, place the device in accordance with the manufacturer's pin-description table and keep input and supply paths compact. Decouple the 5 V rail close to the supply pin, provide a low-impedance ground connection, and route each receiver input away from switching nodes. Confirm that every unused output has a defined downstream state and that CONT pins are configured for the intended threshold and filtering behavior. This product record combines the manufacturer's device information, package and interface details, an RS-232-oriented engineering description, drop-in replacement analysis, comparison parameters, and practical layout guidance. It is intended to support component selection and board-level implementation without obscuring the distinctions that must be checked before approving a substitution.

Devis Contact
SN75HVD1176 - 40Mbps PROFIBUS RS-485 Transceiver | Texas Instruments
SN75HVD1176

SN75HVD1176 - 40Mbps PROFIBUS RS-485 Transceiver | Texas Instruments

The Texas Instruments SN75HVD1176 is a half-duplex PROFIBUS RS-485 transceiver that meets or exceeds the requirements of ANSI TIA/EIA-485-A for differential data transmission across twisted-pair networks, signaling at up to 40 Mbps. It is offered in an 8-pin SOIC package and integrates a differential driver, differential receiver, and bus-idle fail-safe circuitry on a single die, with a 1/5 unit load that permits up to 160 nodes on a single bus. An RS-485 transceiver is a physical-layer interface IC that converts a single-ended TTL/CMOS logic signal into a robust differential voltage on a twisted-pair bus, and vice versa. RS-485 belongs to the EIA/TIA-485 standard family and is widely used in industrial multipoint networks because it supports long cable runs, high noise immunity, and multiple node addresses. PROFIBUS (Process Field Bus, IEC 61158/EN 50170) is an industrial fieldbus protocol that imposes tighter symmetry, rise/fall time, and voltage-swing requirements on the transceiver than generic RS-485. SN75HVD1176 targets that PROFIBUS envelope while remaining backward-compatible to RS-485, sitting in the hierarchy: PROFIBUS transceiver -> RS-485 transceiver -> differential line transceiver -> physical-layer IC -> wired communication IC -> semiconductor. Key features include signaling rates up to 40 Mbps, 1/5 unit load (up to 160 nodes), low bus capacitance of 10 pF maximum, thermal shutdown protection, short-circuit-protected bus pins, and an industrial -40C to +85C operating temperature range. The differential output voltage exceeds 2.1V into a 54 ohm load, comfortably meeting the PROFIBUS VOD minimum while leaving margin for cable loss. Driver enable (DE) and receiver enable (RE) pins support direction control and half-duplex arbitration. The device uses a bipolar CMOS-DMOS process that integrates ESD cells, bus-tap protection, and a precision differential comparator on the receive path. Internal fail-safe biasing forces a deterministic logic-high on R when the bus is idle, shorted, or open, eliminating the need for external fail-safe resistors on most networks. The 10 pF maximum bus pin capacitance helps maintain signal integrity at 40 Mbps on long stubs and many-node buses. Typical applications include PROFIBUS-DP master and slave nodes, RS-485 industrial backbones, factory-floor PLC I/O expansion, motor-drive isolated communication channels, building automation networks, and any 5V industrial multipoint data link that must interoperate with PROFIBUS DP/PA gateways or legacy RS-485 masters. When designing with this part, place a 100 nF decoupling capacitor within 2 mm of VCC and provide a low-impedance ground return for bus-pin ESD currents. Maintain 100 ohm characteristic-impedance twisted pair and use fail-safe biasing only when the standard internal biasing does not meet the application idle-state requirement. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, including same-brand family alternatives and cross-brand pin-compatible equivalents verified against the TI datasheet.

Devis Contact
SN75LVDS84ADGG - FlatLink 21:3 LVDS Transmitter | Texas Instruments
SN75LVDS84ADGG

SN75LVDS84ADGG - FlatLink 21:3 LVDS Transmitter | Texas Instruments

The Texas Instruments SN75LVDS84ADGG is a FlatLink™ LVDS serializer transmitter that compresses 21 bits of parallel LVTTL data into 3 LVDS data pairs plus 1 LVDS clock pair, supporting throughput up to 196 MBps (MegaBytes per second). Packaged in a 48-pin TSSOP (DGG) with an operating temperature range of 0°C to +70°C, it is purpose-built for graphic-controller-to-display interconnects such as SVGA, XGA, and SXGA LCD panels. An LVDS serializer (also called an LVDS transmitter, FlatLink, or channel link) is a parallel-to-serial interface IC belonging to the broader LVDS (Low-Voltage Differential Signaling) family of interface ICs. The category hierarchy is: LVDS serializer → LVDS interface IC → display interface → signal conditioning IC → interface IC. LVDS transmits data as a small differential current (~3.5 mA) across a 100 Ω termination, producing low-EMI, low-power, high-speed point-to-point links over twisted-pair cabling or PCB traces. Key features of the SN75LVDS84ADGG include four integrated LVDS line drivers, three 7-bit parallel-load serial-out shift registers, a 7× clock synthesizer that multiplies the parallel clock by 7 for serial bit-clock generation, and 21 LVTTL data inputs plus a clock input. The on-chip PLL generates the high-speed serialization clock from a low-frequency reference, eliminating the need for an external high-frequency oscillator. The device is typically paired with an SN75LVDS82 / SN75LVDS86A receiver at the display end. Architecturally, the SN75LVDS84A uses a PLL-based 7:1 serialization scheme per channel. Each LVTTL data bit is sampled on the rising edge of the parallel clock, latched into a shift register, then clocked out at 7× the input clock frequency onto its differential pair. This architecture achieves aggregate throughput of 196 MBps while consuming only about 100 mW typical power from a single 3.3 V supply. The receiver counterpart (SN75LVDS82/SN75LVDS84A pair) reverses this process, recovering the parallel data and clock from the three LVDS data pairs. Typical applications include notebook LCD panels, desktop monitor controllers, industrial flat-panel displays, and point-of-sale terminals using XGA/SXGA TFT panels. The TSSOP-48 footprint is the de-facto standard for FlatLink chipsets, enabling drop-in compatibility across the SN75LVDS84A family and most third-party clones. The SN65LVDS84AQ variant provides the same functionality with automotive-grade qualification (AEC-Q100) for in-vehicle display systems. When designing with this device, pay close attention to PCB layout: the four LVDS differential pairs should be routed as 100 Ω-impedance matched pairs with intra-pair skew under 50 ps, and the LVTTL bus should be length-matched to within ±1 inch to avoid setup/hold violations at the rising-edge sample point. A 100 Ω termination resistor across each LVDS pair at the receiver end is mandatory for proper signal swing.

Devis Contact