Produits (44 000+)

TUSB1002RGER - 10Gbps Dual USB 3.1 Redriver | Texas Instruments
TUSB1002RGER

TUSB1002RGER - 10Gbps Dual USB 3.1 Redriver | Texas Instruments

The Texas Instruments TUSB1002RGER is a 10 Gbps dual-channel linear USB 3.1 redriver and signal conditioner in a 24-VQFN package measuring 4 x 4 mm. It operates from a 3.3 V supply, supports USB 3.1 SuperSpeedPlus signal rates, and can compensate for up to 16 dB of Inter-Symbol Interference loss. Its two-channel architecture allows one device to condition both sides of a USB link or two independent USB 3.1 paths. A linear redriver is a type of USB signal conditioner that receives a degraded high-speed differential signal, restores its amplitude and timing margin, and retransmits the signal toward the next USB device. In the broader electronics hierarchy, a redriver belongs to the interface IC and signal-conditioning categories, where it complements controllers, hubs, transceivers, and retimers by recovering connectivity over cables, connectors, and printed circuit board traces. The TUSB1002 uses a linear equalizer to address high-frequency attenuation. According to the Texas Instruments product information, it supports up to 16 dB of loss caused by Inter-Symbol Interference. The device also implements USB 3.1 low-power modes and an ultra-low-power architecture, helping reduce consumption during idle operation. Its 3.3 V supply requirement and 10 Gbps throughput suit equipment requiring long reaches between a USB host or hub and a peripheral. The dual-channel arrangement gives designers flexibility for link-to-link signal conditioning. Each channel can be evaluated and configured for its own PCB or cable path, while common package placement simplifies routing around USB connectors. As a linear device, it preserves the signal waveform while improving amplitude; unlike a protocol-aware retimer, it does not need to recover and reconstruct USB timing at a data rate of 10 Gbps. Typical uses include USB 3.1 docking stations, laptop and tablet accessories, external storage enclosures, industrial test equipment, servers, and data-acquisition systems. It is particularly useful when connector or PCB losses threaten eye closure between a USB host controller and an endpoint device. Place the redriver close to the loss-producing connector or trace segment and follow the manufacturer datasheet's reference layout for high-speed differential routing. Decoupling, impedance control, return-path continuity, and the device's documented layout requirements are essential because an incorrectly positioned redriver can add loss rather than recover margin. This page combines the manufacturer product description with engineering-oriented application analysis, design guidance, lifecycle considerations, and a strict review of drop-in replacement candidates. It is intended to help engineers determine whether the TUSB1002RGER fits a 10 Gbps USB 3.1 channel before committing it to a high-speed PCB layout.

Devis Contact
TUSB1105RGTR - USB 2.0 Transceiver | Texas Instruments
TUSB1105RGTR

TUSB1105RGTR - USB 2.0 Transceiver | Texas Instruments

Texas Instruments TUSB1105RGTR is a single-channel USB 2.0 transceiver for full-speed and low-speed signaling, supporting 12 Mbit/s and 1.5 Mbit/s data rates in a 16-pin VQFN package measuring 3 mm by 3 mm. The device provides one transceiver path, integrates transmit and receive functions, and is designed for compact USB interface implementations. A universal serial bus transceiver is an interface circuit that converts logic-level data into USB-compatible differential signaling and converts received differential signals back into digital logic. The TUSB1105 belongs to the USB interface IC hierarchy, where USB transceivers connect a host, peripheral, or embedded controller to a USB connector while providing the physical-layer signaling required by USB 2.0 devices. The principal features include compliance with the Universal Serial Bus Specification Revision 2.0, full-speed operation at 12 Mbit/s, low-speed operation at 1.5 Mbit/s, and a half-duplex 1/1 transceiver configuration. Its 16-VQFN package is 3 mm by 3 mm, making the device suitable for space-constrained portable, industrial, and embedded USB equipment. The exposed-pad package also supports compact PCB layouts when its land pattern and thermal design are implemented correctly. The TUSB1105 is intended for external USB connectivity rather than direct USB data signaling across a long cable or printed circuit board. Its transmit and receive path handles the USB differential interface, while the connected USB controller or embedded processor performs protocol handling. This division keeps low-level signaling separate from the higher layers of USB enumeration, descriptors, classes, and transfers. Typical uses include USB-to-serial adapters, portable test and measurement equipment, industrial control panels, data-collection terminals, and accessory controllers that need a compact full-speed or low-speed USB interface. For designs that expose a USB Type-A or USB Type-B receptacle, the transceiver should be paired with the appropriate connector, protection network, routing geometry, and controller-specific interface requirements. PCB implementation requires careful treatment of the differential USB pair, the exposed ground pad, and the short connection between the transceiver and connector. Maintain a continuous ground reference, route D+ and D+ together and D− and D− together, and minimize stubs and unnecessary vias. Confirm the final layout against the pin-description and layout guidance in the manufacturer datasheet. This page combines the confirmed USB 2.0 speed ratings, package information, drop-in replacement findings, interface-selection guidance, and practical PCB considerations into a compact engineering reference for USB transceiver designs.

Devis Contact
TUSB1106PWR USB 2.0 Transceiver | Texas Instruments
TUSB1106PWR

TUSB1106PWR USB 2.0 Transceiver | Texas Instruments

The Texas Instruments TUSB1106PWR is a single-channel USB transceiver for Universal Serial Bus applications, supporting full-speed operation at 12 Mbit/s and low-speed operation at 1.5 Mbit/s. The device is compliant with the Universal Serial Bus Specification Revision 2.0 and is packaged in a 16-pin TSSOP (PW) package. It integrates the digital transceiver functions required for a USB host, device, or peripheral interface. A USB transceiver is an interface integrated circuit that converts between a host controller or peripheral controller’s digital signaling and the physical D+ and D- differential pair used by USB. In the broader electronics hierarchy, the TUSB1106 belongs to the USB interface IC family, interface transceivers, and power-management-aware connectivity semiconductors. It provides the physical-layer path for exchanging serial data and detecting bus state in USB 2.0 systems. The TUSB1106 family supports both full-speed and low-speed USB data rates. Full-speed operation provides a higher-rate communication option for peripherals that require more throughput, while low-speed operation supports devices with modest bandwidth requirements and suitable device-state behavior. USB 2.0 Revision 2.0 compliance is specifically identified for the TUSB1105 and TUSB1106 transceivers by Texas Instruments. The TUSB1106PWR is a half-duplex, one-channel transceiver, matching the “1/1 Transceiver Half” device description shown in the product listing. Its differential USB data interface connects to the external data and power behavior of the USB link, while control and configuration pins support integration into host or peripheral designs. The single USB channel makes the device appropriate for compact equipment, industrial control modules, embedded systems, and accessory interfaces that require one USB physical transceiver. Typical design locations include USB host controllers, USB peripheral controllers, portable test equipment, industrial interface cards, and embedded USB-to-serial or USB communication subsystems. The device should be placed near the USB connector so that the high-speed differential traces remain short, continuous, and impedance controlled. Connector-side protection, proper D+ and D- routing, and compliance with the USB signal-integrity requirements are more important than adding unrelated circuit functions. When designing a replacement circuit, verify the complete pin description, electrical limits, operating-temperature range, and USB compliance requirements against the manufacturer datasheet. The principal engineering trade-off is that this device supports USB 2.0 full-speed and low-speed signaling rather than USB high-speed operation at 480 Mbit/s. For new designs that require high-speed USB data rates, select a transceiver explicitly specified for that speed instead. This page organizes the verified manufacturer and distributor information into an engineering-oriented view covering USB data rates, package format, application fit, comparison criteria, and practical design guidance. The package and interface hierarchy are emphasized so engineers can identify whether the TUSB1106PWR matches the intended USB physical-layer design.

Devis Contact
TUSB1106RTZR - USB 2.0 Half-Speed Transceiver | TI
TUSB1106RTZR

TUSB1106RTZR - USB 2.0 Half-Speed Transceiver | TI

Texas Instruments TUSB1106RTZR is a half-speed USB 2.0 transceiver that transmits and receives serial data at both 12 Mbit/s full-speed and 1.5 Mbit/s low-speed rates. The device is packaged in a 16-pin WQFN (RTZ) 3 x 3 mm surface-mount package and includes an integrated bypassable 3.3 V regulator for powering devices from USB VBUS. A USB transceiver is an interface IC that translates logic-level data between a host or hub and a USB peripheral. It belongs to the USB interface transceiver class within the broader interface IC and semiconductor hierarchy. This dual-rate capability allows one device to support both full-speed and low-speed USB links, making it useful in peripheral controllers, portable equipment, industrial interfaces, and legacy USB connectivity designs. The TUSB1106 is compliant with the Universal Serial Bus Specification Revision 2.0. Its principal data-rate ratings are 12 Mbit/s for full-speed operation and 1.5 Mbit/s for low-speed operation. The integrated 3.3 V regulator can be bypassed, giving the system designer a choice between using VBUS-derived power and controlling the regulator enable function. The 16-WQFN package supports compact surface-mount layouts while providing an exposed pad for improved board-level thermal performance. Operation at both USB speed rates expands compatibility with USB peripherals that use full-speed or low-speed signaling. The half-speed transceiver architecture implements one transmit path and one receive path, while the integrated regulator reduces the number of external power-management functions required around a USB peripheral. Designers must still account for USB data-line impedance, ESD protection, connector routing, and the regulator bypass configuration in the system schematic. Typical uses include USB-to-serial bridges, embedded USB peripherals, portable data-acquisition equipment, industrial control interfaces, and USB connectivity for legacy full-speed or low-speed devices. The compact 3 x 3 mm package is particularly useful when board area is constrained but a full USB interface is required without relying on a larger host-side controller. For PCB implementation, route D+ and D+ as a controlled-impedance differential pair, connect the data lines according to the manufacturer's reference layout, and place ESD protection close to the connector. Decouple the 3.3 V output according to the device's recommended capacitor network and verify whether the integrated regulator should be bypassed for the selected power architecture. This product page combines the manufacturer's USB 2.0 compliance information, exact package and temperature details, commercial sourcing guidance, and an analysis of same-footprint alternatives to support faster component selection and PCB design.

Devis Contact
TUSB1146RNQR - 10Gbps USB-C Redriver/MUX | Texas Instruments
TUSB1146RNQR

TUSB1146RNQR - 10Gbps USB-C Redriver/MUX | Texas Instruments

The Texas Instruments TUSB1146RNQR is a USB Type-C crosspoint switch and protocol-agnostic linear redriver supporting USB 3.2 data rates up to 10 Gbps and VESA DisplayPort 2.0 up to 10 Gbps. The device is available in a 40-pin WQFN package measuring 6 mm by 4 mm, with an operating temperature range of 0 °C to 70 °C. It supports USB 3.2 SuperSpeed Plus, two DisplayPort lanes, four DisplayPort lanes, and DisplayPort D_DFP pin assignments C, D, and E. A USB Type-C alternate-mode redriver/MUX is an interface IC that routes high-speed signals between a USB Type-C connector and downstream or host circuitry while compensating for channel loss. It belongs to the signal-conditioning hierarchy of USB interface controllers, redrivers, repeaters, crosspoint switches, and interface ICs. By regenerating and equalizing marginal signals, the TUSB1146 supports reliable high-speed links over longer traces, connectors, cables, or board-to-board transitions than might be possible with passive routing alone. The TUSB1146 supports USB 3.2 Gen 1 and Gen 2 operation up to 10 Gbps, two-lane and four-lane DisplayPort configurations, and DisplayPort 2.0 UHBR10 signaling up to 10 Gbps. Its adaptive equalization adapts the receive equalization to the connected channel. The protocol-agnostic architecture also allows the device to support non-DisplayPort USB Type-C alternate modes such as HDMI Alternate Mode. In a downstream-facing host port, the TUSB1146 functions as a linear redriver for selected USB Type-C SuperSpeed and DisplayPort lanes. Adaptive equalization helps restore signal margin when connector or PCB losses reduce eye opening. The linear redriver architecture is particularly useful where designers need signal regeneration without introducing a protocol-specific conversion stage between the Type-C port and the downstream interface. Typical uses include USB-C docking stations, laptop and tablet docks, multiport adapters, monitor docks, video-capture systems, and industrial USB-C equipment. The D_DFP C, D, and E assignments broaden compatibility with DisplayPort Alternate Mode routing requirements. Systems requiring additional lane routing, conversion, or protocol features should confirm the complete pin configuration and application circuit in the manufacturer datasheet before layout release. Layout is critical in a 10 Gbps redriver design. Route the high-speed differential pairs as controlled-impedance, tightly coupled traces with minimal stubs and continuous reference planes. Place bypass capacitors close to the supply pins, keep the exposed pad thermally and electrically connected as specified, and follow the manufacturer’s recommended layer transitions and return-path guidance to minimize differential-mode and common-mode conversion. This product page combines interface classification, application guidance, design cautions, and structured comparison fields to support faster engineering review. It also separates confirmed TUSB1146RNQR characteristics from parameters that still require inspection of the manufacturer datasheet, helping designers avoid assuming unsupported pin, electrical, or compliance details.

Devis Contact
TUSB1146RNQT - 10Gbps USB-C Alt Mode Redriver | TI
TUSB1146RNQT

TUSB1146RNQT - 10Gbps USB-C Alt Mode Redriver | TI

The Texas Instruments TUSB1146RNQT is a protocol-agnostic USB Type-C Alt Mode redriver and crosspoint switch that supports USB 3.2 data rates up to 10 Gbps and DisplayPort 2.0 up to 10 Gbps. The device is housed in a 40-pin WQFN package measuring 6 mm by 4 mm and is intended for downstream-facing host ports. A USB Type-C Alt Mode redriver is an interface IC that conditions high-speed differential signals between a USB Type-C controller and a connector or peripheral. It supports loss compensation for USB, DisplayPort, and other protocol-agnostic Alt Mode lanes. The TUSB1146 occupies the redriver, multiplexing, and signal-conditioning stages of a USB Type-C power and data interface. The TUSB1146 supports USB 3.2 SuperSpeed signals at up to 10 Gbps and VESA DisplayPort 2.0 at up to 10 Gbps, or UHBR10. It supports USB 3.2 x1 Gen 1 and Gen 2, USB 3.2 SSP, two DisplayPort lanes, and four DisplayPort lanes. Its protocol-agnostic architecture also permits use with other USB Type-C Alt Mode interfaces, including HDMI Alt Mode. The TUSB1146 provides adaptive equalization to compensate for channel loss encountered through PCB traces, connectors, and cables. Its crosspoint-switch architecture supports configurable lane routing for USB and DisplayPort Alt Mode. The manufacturer identifies support for DisplayPort D_DFP pin assignments C, D, and E, making it suitable for systems that require multiple high-speed lane arrangements in a compact host interface. Typical uses include USB-C docking stations, multi-display adapters, notebook and tablet systems, desktop hosts, video-over-USB-C equipment, and industrial data-acquisition systems. The device is particularly relevant where cable or PCB losses could compromise 10 Gbps signal integrity but the host and connector placement cannot be shortened enough to eliminate the loss. When laying out a design, preserve the high-speed signal paths as short and symmetric as possible, provide the reference-plane and return-path structures required by the manufacturer recommendations, and place bypass capacitance close to the supply pins. Differential pair geometry and connector launch transitions are especially important at 10 Gbps because the redriver compensates for loss but cannot remove reflections caused by an inconsistent PCB structure. This page combines the TUSB1146RNQT protocol and package details, application guidance, sourcing information, and a strict assessment of available drop-in replacements. It is intended to help engineers confirm protocol coverage, mechanical fit, thermal expectations, and signal-integrity requirements before integrating the redriver into a USB Type-C Alt Mode design.

Devis Contact
TUSB1310AZAY - 5 Gbps USB 3.0 Transceiver | Texas Instruments
TUSB1310AZAY

TUSB1310AZAY - 5 Gbps USB 3.0 Transceiver | Texas Instruments

Texas Instruments TUSB1310AZAY is a single-port SuperSpeed USB 3.0 physical-layer transceiver with a 5.0 Gbps data rate, PIPE and ULPI interfaces, and a 175-NFBGA package measuring 12 x 12 mm. It operates from one selectable reference clock at 20, 25, 30, or 40 MHz and can provide that clock to a USB controller. A USB 3.0 transceiver is an interface IC that connects a USB controller or host to a SuperSpeed data link. It forms part of the hierarchy USB interface device, transceiver, interface IC, and semiconductor. Unlike a passive connector, the transceiver converts parallel controller data into high-speed differential signaling and receives differential signal information for the controller. The TUSB1310A also supports PIPE and ULPI interfaces, allowing it to connect with controllers that use either interface style. Principal features include one USB 3.0 port, a 5.0 Gbps maximum data rate, four selectable reference-clock frequencies, and integrated USB power-state handling. The USB 3.0 power states named in the manufacturer documentation are U0, U1, U2, and U3. The PIPE specification defines P0, P1, P2, and P3, while the POWER_DOWN pin is mapped to LTSSM states as described in the manufacturer datasheet. The device operates from a single reference clock supplied by either a crystal or an external clock source. The manufacturer describes the 20, 25, 30, and 40 MHz selection as enabling a cost-effective USB 3.0 implementation with few external components. Because the transceiver can provide the reference clock to the USB controller, the design can reduce the number of independent clock sources required on the board. Typical uses include USB 3.0 host-controller systems, USB device controllers, external data-transfer equipment, test and measurement products, and embedded computing platforms that require a SuperSpeed interface. The PIPE and ULPI choices are particularly useful when a system already has a controller designed around one of those interfaces. The 175-NFBGA package also supports compact layouts where the electrical and thermal design can be controlled carefully. When implementing the TUSB1310AZAY, follow the manufacturer datasheet for high-speed differential routing, reference-clock configuration, supply decoupling, ball assignment, and test-point access. Its 12 x 12 mm BGA footprint requires careful escape routing and multilayer PCB planning. Confirm that the selected controller supports the intended PIPE or ULPI mode and verify the complete USB link-training sequence during hardware validation. This page consolidates the exact ordering information, interface capabilities, clock choices, package details, replacement information, and engineering design considerations for engineers evaluating a USB 3.0 SuperSpeed physical-layer implementation.

Devis Contact
TUSB1310ZAY - 5Gbps USB 3.0 Transceiver | Texas Instruments
TUSB1310ZAY

TUSB1310ZAY - 5Gbps USB 3.0 Transceiver | Texas Instruments

The Texas Instruments TUSB1310ZAY is a single-port, 5.0-Gbps USB 3.0 SuperSpeed physical-layer transceiver with PIPE3 and ULPI interfaces, packaged in a 175-ball NFBGA measuring 12 x 12 mm. It accepts a single crystal or external reference clock and can supply a clock to a USB link-layer controller. According to the manufacturer product page, selectable reference-clock frequencies include 20, 25, 30, and 40 MHz, supporting integration into USB 3.0 systems that require a consolidated physical-layer and controller-interface solution. A USB 3.0 SuperSpeed transceiver is the interface device that converts between a host or device controller and the physical USB data path. It belongs to the USB interface IC hierarchy, connects to digital logic through PIPE3 or ULPI, and handles the high-speed physical signaling required by the USB 3.0 protocol. The TUSB1310 therefore sits between a USB link-layer controller and the external connector, power, clock, and signal-routing network. The principal documented features are one USB 3.0 transceiver port, a 5.0-Gbps operating speed, support for both PIPE3 and ULPI controller interfaces, and operation from either a crystal oscillator or an external reference clock. Its four documented reference-clock choices allow the system designer to select a clock appropriate to the controller ecosystem. The device can also provide a clock to the USB link-layer controller, reducing the number of separate clocking arrangements considered in a reference design. The TUSB1310ZAY uses a 175-NFBGA package, identified by the ordering code as a 12 x 12 mm device. This dense ball-grid arrangement is intended for compact systems requiring numerous high-speed connections. Placement is a signal-integrity-critical task because USB 3.0 differential pairs demand short, length-matched routing, appropriate reference planes, and carefully controlled return paths. The transceiver’s interface selection also affects host-versus-device implementation and determines how the controller-facing pins are connected. Typical applications include USB 3.0 docking stations, high-speed data-transfer products, storage systems, test equipment, and embedded computing platforms that use a USB link-layer controller. The transceiver can suit designs requiring either PIPE3 connectivity for parallel controller integration or ULPI connectivity for a compact register-oriented interface. It is particularly relevant where a system needs one USB 3.0 port and a selectable reference-clock arrangement rather than a multi-port hub transceiver. When designing around the TUSB1310ZAY, verify the complete pin configuration, electrical limits, crystal or reference-clock requirements, and decoupling recommendations in the manufacturer datasheet before releasing PCB artwork. High-speed differential routing should be validated against the controller and connector reference designs because package placement, via transitions, layer stackup, and clock jitter can materially affect signal integrity. This page organizes the documented TUSB1310ZAY capabilities, package information, interface options, engineering applications, and confirmed same-package alternatives. It also highlights where a manufacturer data sheet must remain the controlling reference for pin assignment, compliance, environmental limits, and layout implementation.

Devis Contact
TUSB2036AVF - 2/3-Port 12Mbps USB Hub | Texas Instruments
TUSB2036AVF

TUSB2036AVF - 2/3-Port 12Mbps USB Hub | Texas Instruments

Texas Instruments TUSB2036AVF is a 2/3-port, 12-Mbps USB full-speed hub controller with an optional serial EEPROM interface, housed in a 32-pin LQFP package. The device operates from a 3.3-V supply and provides one upstream port plus two or three programmable downstream ports. Its USB 2.0-compliant implementation integrates transceivers for every upstream and downstream connection, while a digital state-machine architecture eliminates firmware programming requirements. A USB hub is a system-level interface component that expands one host connection into multiple peripheral ports. The TUSB2036AVF belongs to the USB interface controller hierarchy, combining USB transceiver circuitry, port-management logic, and optional configuration storage in one CMOS ASIC. This integration simplifies PCB design for legacy full-speed USB systems, printers, industrial peripherals, and embedded equipment that require more than one USB device connection. Key features include integrated upstream and downstream USB transceivers, selectable two- or three-port operation, 12-Mbps full-speed data transfer, and an optional serial EEPROM interface. Because the downstream-port count is selected through an input pin, one board design can support two-port or three-port configurations without changing the controller IC. The digital state-machine implementation also means the hub does not require embedded hub firmware. The controller uses a 3.3-V CMOS logic implementation and provides dedicated USB transceiver functions for all supported ports. Its architecture is intended for full-speed USB 2.0-compatible systems rather than high-speed 480-Mbps operation. Power, decoupling, routing, and signal-integrity layouts must therefore be evaluated specifically for 12-Mbps full-speed signaling rather than high-speed USB impedance rules. Typical applications include USB-to-multiple-peripheral adapters, legacy printer interfaces, industrial control equipment, data acquisition systems, and embedded host platforms using full-speed USB peripherals. The optional EEPROM interface allows port configuration to be stored externally, which is useful when a product requires consistent downstream-port behavior across power cycles. When laying out the PCB, place the controller and supporting passive components close to their associated connector and power-entry points. Keep USB differential traces short, pair them continuously, minimize stub branches, and provide the decoupling network specified by the manufacturer. Confirm the selected two-port or three-port configuration and verify downstream-port power switching before releasing the layout. This page organizes the official product information into a design-oriented view covering USB speed, port topology, logic voltage, configuration options, package considerations, application fit, and replacement limitations. It also distinguishes confirmed device functions from assumptions that require engineering verification against the manufacturer datasheet.

Devis Contact
TUSB2036VFG4 - 12Mbps 3-Port USB Hub | Texas Instruments
TUSB2036VFG4

TUSB2036VFG4 - 12Mbps 3-Port USB Hub | Texas Instruments

Texas Instruments TUSB2036VFG4 is a 3.3 V CMOS USB 2.0 full-speed hub controller with a 12 Mbps data rate, two or three downstream ports, and an optional serial EEPROM interface. The device is packaged in a 32-pin LQFP measuring 7 mm by 7 mm. It is designed for systems that need to expand one USB host connection into multiple full-speed peripheral ports without requiring firmware or an external microcontroller. A USB hub controller is a dedicated interface semiconductor that manages traffic between an upstream USB host and one or more downstream devices. It belongs to the USB interface IC hierarchy and broader interface semiconductor category. A full-speed USB 2.0 hub operates at 12 Mbps, making it appropriate for keyboards, mice, printers, human-interface devices, data acquisition equipment, and other peripherals that do not require high-speed or SuperSpeed USB signaling. The TUSB2036VFG4 supports up to three downstream ports and can use a serial EEPROM for configuration storage when the application requires field-programmable hub behavior. Its digital state-machine implementation requires no firmware programming. A 3.3 V operating supply and full-speed USB operation simplify integration into equipment containing legacy USB peripherals, while the 32-LQFP package provides a conventional surface-mount footprint for industrial control, instrumentation, and embedded systems. The TUSB2036 family uses a digital state machine rather than a microcontroller core to control hub functions. This architecture can reduce software complexity because port behavior is handled by dedicated hardware. The manufacturer describes the TUSB2036 as compliant with the USB 2.0 specification for 2/3-port, 12 Mbps full-speed operation. Exact port-disable, power-control, bus-power, and configuration behavior should be confirmed against the pin description and application information in the manufacturer datasheet before board release. Typical uses include industrial test equipment, laboratory instruments, printers, point-of-sale terminals, embedded computers, and USB expansion cards. The hub can consolidate several low-speed or full-speed peripherals behind one upstream host connection. In self-powered equipment, designers must implement the required power-distribution architecture and ensure downstream devices receive adequate bus power. Systems with many high-current peripherals may require external power rather than relying entirely on the upstream USB supply. PCB implementation should preserve short, impedance-controlled USB signal paths and provide solid ground-plane continuity between the controller and connected ports. Place USB differential lines as a matched pair, minimize stub lengths, and keep switching regulators and inductors away from the 12 Mbps data traces. Decoupling and protection components should follow the connection and routing guidance in the manufacturer datasheet. This page combines manufacturer specifications, package and interface details, ordering guidance, comparison data, and practical integration notes. These engineering-focused details help designers determine whether the TUSB2036VFG4 fits a USB full-speed expansion requirement before beginning PCB layout or prototype assembly.

Devis Contact
TUSB2040AN - 4-Port USB 1.0 Hub Controller | Texas Instruments
TUSB2040AN

TUSB2040AN - 4-Port USB 1.0 Hub Controller | Texas Instruments

The Texas Instruments TUSB2040AN is a 3.3 V CMOS four-port Universal Serial Bus hub controller with an optional serial EEPROM interface, supplied in a 28-pin PDIP package. It provides up to four downstream USB ports and supports USB specification version 1.0. The TUSB2040AN belongs to the USB interface controller hierarchy, combining host-interface, port-management, and downstream-port switching functions in one integrated circuit. A USB hub controller is a semiconductor that manages a shared USB connection and distributes it among multiple downstream peripherals. It sits between a USB host and attached devices, supporting device attachment, enumeration, and port routing. The TUSB2040A device family was designed for USB 1.0 systems in which up to four downstream ports are required and an optional serial EEPROM can provide configuration or hub-specific information. The principal verified characteristics of the TUSB2040AN are its four downstream ports, 3.3 V CMOS operation, USB 1.0 support, optional serial EEPROM interface, and 28-pin PDIP package. Its parallel host-side data and control paths are intended for conventional low-speed and full-speed Universal Serial Bus designs. The integrated hub function reduces the number of separate discrete interface components required around a host port. The TUSB2040A architecture includes separate downstream differential data connections for the four hub ports and an upstream connection to the USB host. Configuration information can optionally be supplied through a serial EEPROM, allowing a board designer to support application-specific hub behavior without relying entirely on fixed internal configuration. Exact electrical limits, timing values, and operating-temperature data must be taken from the manufacturer datasheet. Typical uses include legacy USB keyboards, mice, printers, industrial data-acquisition equipment, educational laboratory computers, and embedded host systems that need to expand one host connection into four downstream ports. A prototype can also be used to verify USB enumeration, peripheral attachment, and power-management behavior before the PCB layout is released. PCB design should preserve short USB differential traces, continuous ground references, controlled impedance, and proper separation from noisy switching nodes. The optional serial EEPROM interface requires stable address, clock, and data routing, while unused inputs and outputs must follow the manufacturer’s termination and connection guidance. Because the verified search results do not provide a complete pin table or detailed application circuit, those items should be confirmed against the manufacturer documentation before layout. This product record combines the verified distributor and datasheet-search information with structured engineering guidance. It also explicitly identifies unavailable pricing, lifecycle, pinout, and substitution data instead of presenting unverified substitutions as drop-in alternatives.

Devis Contact
TUSB2040APT - 4-Port USB 1.0 Hub Controller | Texas Instruments
TUSB2040APT

TUSB2040APT - 4-Port USB 1.0 Hub Controller | Texas Instruments

Texas Instruments TUSB2040APT is a 3.3 V CMOS four-port Universal Serial Bus hub controller with an optional serial EEPROM interface, supplied in a 48-pin PQFP package. The device provides four downstream USB ports and supports USB 1.0 low-speed and full-speed operation according to the Texas Instruments manufacturer datasheet. A USB hub controller is an interface integrated circuit that expands one upstream USB connection into multiple downstream ports. In the USB interface hierarchy, the TUSB2040APT sits between a host controller and connected peripherals, adding port management, shared-bus coordination, and optional configuration-memory support. It is designed for legacy USB 1.0 equipment rather than current USB 2.0, USB 3.x, or Type-C ecosystems. The principal feature is four downstream ports in one controller. This allows several USB peripherals to share an available host USB port while the hub manages downstream traffic. The optional serial EEPROM interface provides a path for hub descriptors and configuration data, which can be important when the host must identify the hub correctly. The controller operates from a 3.3 V CMOS supply. The 48-pin PQFP package exposes separate USB data and clock connections for the upstream interface and downstream ports, together with power, configuration, enable, and interrupt-related functions. Because this is a legacy USB 1.0 hub implementation, system design should verify signal routing, termination, bus capacitance, enumeration behavior, and downstream-current requirements against the manufacturer datasheet rather than assuming compatibility with newer USB standards. Typical uses include industrial data-acquisition equipment, legacy test systems, embedded service interfaces, printer or peripheral interfaces, and older computer peripherals that require a multiport USB hub. The device is most appropriate when the existing system already uses USB 1.0 and its electrical and enumeration behavior has been validated. Designers should preserve the recommended placement and connection of USB differential pairs, minimize stubs between the controller and connectors, and route high-current supply paths independently from sensitive data signals. Confirm the pin assignment and power requirements in the Texas Instruments manufacturer datasheet before finalizing the PCB because the available product summary does not reproduce the complete pin table. This page organizes the manufacturer device description, package information, sourcing fields, interface applications, and engineering considerations into one focused reference. It also distinguishes what the part actually supports—four-port USB 1.0 hub control with optional EEPROM—from newer hub controllers that require different electrical and firmware support.

Devis Contact
TUSB2040N - 4-Port USB 1.0 Hub Controller | Texas Instruments
TUSB2040N

TUSB2040N - 4-Port USB 1.0 Hub Controller | Texas Instruments

Texas Instruments TUSB2040N is a four-port USB 1.0-compatible hub controller with integrated USB transceivers, per-port power switching, and overcurrent reporting. The device supports four downstream ports and two power-source arrangements: self-powered mode and bus-powered mode. It is packaged as a 28-pin PDIP according to the retrieved distributor records. The verified source identifies the TUSB2040 family as a universal serial bus hub controller and does not provide additional electrical timing, current, or temperature values. A USB hub controller is an interface IC that connects one upstream USB port to multiple downstream ports, allowing peripherals to share a host controller. Within the hierarchy of USB interface devices, transceiver, hub controller, interface IC, and semiconductor, the TUSB2040N provides the logic and physical connectivity for expanding USB 1.0 equipment. Its integrated transceivers reduce the need for separate USB transceiver circuitry on the hub board. The principal verified features are four downstream ports, integrated USB transceivers, USB 1.0 compliance, self-powered operation, bus-powered operation, per-port power switching, overcurrent reporting, per-port or ganged power modes, and suspend support. These functions suit hubs where the host must enumerate multiple peripherals and where each downstream port needs controllable power. The retrieved distributor listing describes the part as an interface controller, while the family datasheet result specifically identifies four-port USB hub functionality. The TUSB2040N is intended for USB 1.0 hub designs, including peripheral expansion, legacy computer interfaces, industrial equipment, and embedded systems that use multiple low-speed, full-speed, or compatible USB devices. Its architecture places port power management close to the USB interface, allowing the design to report overcurrent conditions and manage downstream power distribution. Exact propagation delays, operating voltage, maximum downstream current, and USB data-rate details are not present in the verified web data and must be confirmed from the manufacturer datasheet before a new design is released. For implementation, follow the TUSB2040 family datasheet for pin assignments, transceiver connections, power-source selection, capacitor values, and port-power topology. Pay particular attention to upstream and downstream USB differential routing, ground-plane continuity, and current-limit behavior. Because the verified record lists a PDIP package, verify physical dimensions and pin orientation against the actual manufacturer drawing rather than relying only on distributor metadata. This page combines the verified distributor and datasheet-search records with clearly marked missing-data fields. It does not infer prices, lifecycle claims, pin names, or electrical limits that were not supplied. Buyers should request a quotation for current commercial availability and confirm the exact package, ordering suffix, and production status with Texas Instruments before committing a design to production.

Devis Contact
TUSB2043VF - 4-Port USB Hub with EEPROM | Texas Instruments
TUSB2043VF

TUSB2043VF - 4-Port USB Hub with EEPROM | Texas Instruments

Texas Instruments TUSB2043VF is a four-port USB hub controller with an optional serial EEPROM interface, a 48 MHz oscillator or clock source, and a 32-pin LQFP package. It belongs to the USB interface-controller hierarchy: USB hub controller, USB interface IC, interface integrated circuit, and semiconductor. Its verified device description identifies support for four downstream USB ports while allowing an optional serial EEPROM connection for configuration or device-specific control data. The TUSB2043VF uses a 48 MHz oscillator or clock source as its input clock, as stated in the verified manufacturer-related listing. Because this legacy hub controller depends on a relatively high-frequency clock, PCB layout should preserve short clock paths, provide clean return paths, and decouple supply pins close to the device. The 32-LQFP package offers enough perimeter pins for USB data, power, clock, configuration, and optional EEPROM connections, although a complete verified pin map is not included in the supplied data. A major engineering consideration is USB signal integrity. Each enabled USB data path must be routed as a controlled-impedance differential pair on a multilayer PCB, with minimal stubs and carefully planned layer transitions. Power-distribution inductance can cause transient voltage excursions when a downstream device is attached or removed, so bulk and local decoupling should be evaluated together. The optional serial EEPROM interface adds an additional bus that must be routed with suitable signal-integrity practices. Typical uses include legacy USB hubs, USB expansion equipment, computer peripherals, industrial data-acquisition systems, and embedded host or peripheral designs that require four downstream ports. Engineers should confirm host compatibility, downstream current budget, USB speed, enumerator behavior, electrical characteristics, and mechanical footprint against the manufacturer datasheet before using this obsolete device in a new production design. The principal design tradeoff is lifecycle risk. A distributor result explicitly describes TUSB2043VF as obsolete, while another distributor lists it for purchase or RFQ. For new designs, compare current-generation USB hub controllers unless an existing platform specifically requires the TUSB2043VF footprint and behavior. This page consolidates the verified product description, distributor availability references, package information, lifecycle indication, and explicit data gaps. It also separates known facts from missing parameters so engineers can assess whether the legacy controller remains appropriate without mistaking unverified specifications for manufacturer data.

Devis Contact
TUSB2043VFR - 4-Port USB Hub with EEPROM | Texas Instruments (Tape & Reel)
TUSB2043VFR

TUSB2043VFR - 4-Port USB Hub with EEPROM | Texas Instruments (Tape & Reel)

Texas Instruments TUSB2043VFR is a four-port USB hub controller with an optional serial EEPROM interface, a 48 MHz oscillator or clock source, and a 32-pin LQFP package. It belongs to the USB interface-controller hierarchy: USB hub controller, USB interface IC, interface integrated circuit, and semiconductor. Its verified device description identifies support for four downstream USB ports while allowing an optional serial EEPROM connection for configuration or device-specific control data. The TUSB2043VFR uses a 48 MHz oscillator or clock source as its input clock, as stated in the verified manufacturer-related listing. Because this legacy hub controller depends on a relatively high-frequency clock, PCB layout should preserve short clock paths, provide clean return paths, and decouple supply pins close to the device. The 32-LQFP package offers enough perimeter pins for USB data, power, clock, configuration, and optional EEPROM connections, although a complete verified pin map is not included in the supplied data. A major engineering consideration is USB signal integrity. Each enabled USB data path must be routed as a controlled-impedance differential pair on a multilayer PCB, with minimal stubs and carefully planned layer transitions. Power-distribution inductance can cause transient voltage excursions when a downstream device is attached or removed, so bulk and local decoupling should be evaluated together. The optional serial EEPROM interface adds an additional bus that must be routed with suitable signal-integrity practices. Typical uses include legacy USB hubs, USB expansion equipment, computer peripherals, industrial data-acquisition systems, and embedded host or peripheral designs that require four downstream ports. Engineers should confirm host compatibility, downstream current budget, USB speed, enumerator behavior, electrical characteristics, and mechanical footprint against the manufacturer datasheet before using this obsolete device in a new production design. The principal design tradeoff is lifecycle risk. A distributor result explicitly describes TUSB2043VFR as obsolete, while another distributor lists it for purchase or RFQ. For new designs, compare current-generation USB hub controllers unless an existing platform specifically requires the TUSB2043VFR footprint and behavior. This page consolidates the verified product description, distributor availability references, package information, lifecycle indication, and explicit data gaps. It also separates known facts from missing parameters so engineers can assess whether the legacy controller remains appropriate without mistaking unverified specifications for manufacturer data.

Devis Contact
TUSB2046AVF - 4-Port USB Hub | Texas Instruments
TUSB2046AVF

TUSB2046AVF - 4-Port USB Hub | Texas Instruments

The Texas Instruments TUSB2046AVF is a four-port USB hub controller compatible with USB 1.1 and USB 2.0 full-speed operation at 12 Mbit/s. It uses a 3.3 V low-power ASIC logic implementation, integrates USB transceivers and a state machine, and supports an optional serial EEPROM interface for hub configuration. The device is packaged in a 32-pin LQFP with a 0.8 mm pin pitch. A USB hub controller is a semiconductor interface device that manages one upstream USB connection and distributes it among multiple downstream ports. The TUSB2046AVF belongs to the USB interface-controller hierarchy, where it sits between a host controller or host computer and USB peripherals such as keyboards, mice, printers, storage devices, and industrial USB equipment. Its integrated transceivers reduce the number of external USB data-path components required in a hub design. The principal feature set includes four downstream hub ports, USB full-speed operation at 12 Mbit/s, integrated USB transceivers, integrated state-machine logic, and an optional serial EEPROM interface. The EEPROM connection can provide a configurable hub identity and descriptors when the system designer does not use a different configuration method. A 3.3 V operating rail also allows the controller to operate in conventional 3.3 V digital systems without a dedicated 5 V hub-controller supply. The TUSB2046A controller combines a four-port USB full-speed hub architecture with low-power 3.3 V logic. Because it is a full-speed rather than high-speed USB 2.0 hub controller, its 12 Mbit/s maximum data rate is appropriate for legacy peripherals, keyboards, mice, service interfaces, and other devices that do not require 480 Mbit/s USB high-speed transfers. The optional EEPROM interface adds configuration flexibility without making serial EEPROM mandatory in every implementation. Typical applications include legacy USB expansion, embedded host systems, industrial data-acquisition equipment, USB peripheral connection hubs, and retrofits that add USB connectivity to equipment designed around older host interfaces. In each case, the four-port organization consolidates several full-speed peripherals behind one upstream USB link while keeping the implementation compact. PCB design should preserve short, impedance-controlled USB signal paths, provide clean power and ground distribution, and place input and output capacitance close to the relevant device pins as directed by the manufacturer datasheet. Designers should also verify the upstream and downstream connector overcurrent, power-budget, and USB signal-integrity requirements for the complete hub assembly. This page organizes the confirmed device identity, package details, interface capabilities, sourcing path, application guidance, and verified drop-in alternatives for engineers. Because detailed pin assignments and several electrical limits are not established by the accessible manufacturer material, the datasheet should remain the controlling reference before schematic release or PCB layout approval.

Devis Contact
TUSB2046BVF - 4-Port USB 2.0 Full-Speed Hub | TI (Tape & Reel)
TUSB2046BVF

TUSB2046BVF - 4-Port USB 2.0 Full-Speed Hub | TI (Tape & Reel)

The Texas Instruments TUSB2046BVF is a 4-port USB 2.0 full-speed (12 Mbps) hub controller with one upstream port and four downstream ports, implemented as a pure state-machine (no CPU core) in a 32-pin LQFP (VF, 7x7 mm) package. It operates from a single 3.0 V to 3.6 V supply, drawing approximately 40 mA, over a 0 C to 70 C commercial temperature range. A USB hub controller is a dedicated interface IC that expands a single USB upstream connection into multiple downstream ports, handling enumeration, transaction translation at the protocol level, and per-port power management. Within the system hierarchy it sits in the connectivity layer: interface IC > USB controller > hub controller, alongside host controllers and device controllers in a complete USB subsystem. Key features include full compliance with the USB specification as a full-speed hub (TI design TID #30220231), integrated USB transceivers that eliminate external PHY components, and an optional serial EEPROM interface for storing customized VID/PID and configuration data. Support for Win95/DOS-style operation and a pure hardware state-machine architecture reduce firmware complexity to zero - the hub enumerates automatically on plug-in. The TUSB2046B is fabricated on a low-power 3.3 V ASIC CMOS process. Because there is no embedded microcontroller, no firmware development, flash programming, or in-circuit emulator is required, which shortens qualification cycles and removes a whole class of field-update failure modes. The device supports individual downstream port power switching and overcurrent status inputs for compliant bus-powered and self-powered hub designs. Typical applications include standalone USB hubs, monitor and keyboard-display hubs, industrial and medical equipment USB expansion, and adding USB ports to embedded systems built around host processors without native hub capability. For design, provide 0.1 uF decoupling at each supply pin, strap configuration pins (or fit the optional EEPROM) for power-mode selection, and size port power switches per downstream port load. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
TUSB2046BVFR - 4-Port USB 2.0 Full-Speed Hub | TI
TUSB2046BVFR

TUSB2046BVFR - 4-Port USB 2.0 Full-Speed Hub | TI

The Texas Instruments TUSB2046BVFR is a 4-port USB 2.0 full-speed (12 Mbps) hub controller with one upstream port and four downstream ports, implemented as a pure state-machine (no CPU core) in a 32-pin LQFP (VF, 7x7 mm) package. It operates from a single 3.0 V to 3.6 V supply, drawing approximately 40 mA, over a 0 C to 70 C commercial temperature range. A USB hub controller is a dedicated interface IC that expands a single USB upstream connection into multiple downstream ports, handling enumeration, transaction translation at the protocol level, and per-port power management. Within the system hierarchy it sits in the connectivity layer: interface IC > USB controller > hub controller, alongside host controllers and device controllers in a complete USB subsystem. Key features include full compliance with the USB specification as a full-speed hub (TI design TID #30220231), integrated USB transceivers that eliminate external PHY components, and an optional serial EEPROM interface for storing customized VID/PID and configuration data. Support for Win95/DOS-style operation and a pure hardware state-machine architecture reduce firmware complexity to zero - the hub enumerates automatically on plug-in. The TUSB2046B is fabricated on a low-power 3.3 V ASIC CMOS process. Because there is no embedded microcontroller, no firmware development, flash programming, or in-circuit emulator is required, which shortens qualification cycles and removes a whole class of field-update failure modes. The device supports individual downstream port power switching and overcurrent status inputs for compliant bus-powered and self-powered hub designs. Typical applications include standalone USB hubs, monitor and keyboard-display hubs, industrial and medical equipment USB expansion, and adding USB ports to embedded systems built around host processors without native hub capability. For design, provide 0.1 uF decoupling at each supply pin, strap configuration pins (or fit the optional EEPROM) for power-mode selection, and size port power switches per downstream port load. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
TUSB2046BVFRG4 - 4-Port USB 2.0 Full-Speed Hub | Texas Instruments
TUSB2046BVFRG4

TUSB2046BVFRG4 - 4-Port USB 2.0 Full-Speed Hub | Texas Instruments

The Texas Instruments TUSB2046BVFRG4 is a 4-port USB 2.0 full-speed hub controller operating at 12 Mbps from a 3.3 V supply, housed in a 32-pin LQFP (7x7 mm) package with an optional serial EEPROM interface and a 0C to +70C commercial operating range. A USB hub controller is an interface IC that expands a single upstream USB port into multiple downstream ports, handling enumeration, transaction translation at the protocol level, and port power management. It sits within the USB device hierarchy between the host controller and downstream peripherals, forming a sub-family of the broader USB interface and connectivity IC class within semiconductor interface products. Key features include one upstream port and four downstream ports compliant with the USB 2.0 specification at full speed (12 Mbps), support for both low-speed (1.5 Mbps) and full-speed downstream devices, an optional serial EEPROM interface for storing vendor ID / product ID configuration data, and overcurrent detection inputs with power-switch control outputs for per-port or ganged power switching. Implementation with a digital state machine instead of an embedded microcontroller eliminates firmware development and reduces BOM complexity. Technical depth: because the TUSB2046B is a pure hardware state-machine design, enumeration latency is deterministic and there is no firmware to qualify, update, or corrupt. The 3.3 V CMOS core with integrated 3.3 V regulator support keeps external components minimal, typically requiring only a 6 MHz or 48 MHz clock source, bypass capacitors, and the external power switches for downstream VBUS. Typical applications include PC monitor hubs, docking stations, industrial panel USB expansion, printer and multifunction peripheral front panels, and embedded systems requiring additional USB ports from a single host connection. The 12 Mbps full-speed rating suits HID devices, flash drives, and instrumentation rather than high-bandwidth video or mass-storage arrays. Design consideration: budget downstream VBUS power carefully - each downstream port may supply up to 500 mA at 5 V per the USB specification, so external power MOSFET switches and overcurrent sensing resistors must be sized for the aggregate load, and the OVERCURRENT inputs must be wired to the correct power-switch pins. This page synthesizes distributor pricing context, drop-in alternatives, lifecycle status, and practical design notes not found in the manufacturer datasheet alone.

Devis Contact
TUSB2046IBVF - 4-Port 12-Mbps USB Hub Controller | TI
TUSB2046IBVF

TUSB2046IBVF - 4-Port 12-Mbps USB Hub Controller | TI

Texas Instruments TUSB2046IBVF is a 3.3 V CMOS full-speed USB hub controller with one upstream port, four downstream ports, a 12 Mbps operating rate, and an optional serial EEPROM interface. The device is packaged in a 32-pin LQFP (VF) package with a 0.8 mm terminal pitch and supports an operating temperature range of -40°C to +85°C. A USB hub controller is an interface semiconductor that manages traffic between one host or upstream port and multiple downstream peripherals. Within the USB interface hierarchy, the TUSB2046IBVF combines USB 2.0 full-speed hub connectivity, downstream-port power management, and optional configuration-memory support in one controller. This makes it useful for adding USB connectivity to industrial equipment, embedded systems, printers, test systems, and other peripheral-heavy products. The principal features are four downstream USB ports, one upstream port, full-speed operation at 12 Mbps, 3.3 V CMOS supply operation, and optional serial EEPROM support. The 32-LQFP package provides 32 externally accessible connections for USB data, power, control, configuration, clocking, and ground functions. Its industrial temperature range supports applications requiring operation from -40°C to +85°C. Technically, the device is designed around the Universal Serial Bus specification as a full-speed hub. The optional EEPROM interface allows product-specific hub descriptors and configuration data to be loaded during startup, while the four downstream ports expand a single host connection into multiple peripheral connections. The exact upstream and downstream data-rate support, electrical limits, and descriptor behavior should be confirmed from the manufacturer datasheet before final circuit design. Typical applications include industrial control panels, USB-to-serial expansion equipment, instrumentation, embedded test and measurement systems, peripheral hubs, and compact USB distribution products. In these systems, the controller reduces the need for separate USB switch devices while centralizing port routing and configuration. The principal PCB requirement is careful USB signal routing. Keep upstream and downstream differential pairs short, matched, and away from noisy switching nodes. Confirm the required external EEPROM, crystal or clock components, capacitors, and USB power-distribution network against the manufacturer reference schematic before layout release. This page organizes the TUSB2046IBVF specifications, qualified same-footprint alternatives, interface applications, comparison parameters, and practical implementation guidance. These engineering details help designers evaluate controller compatibility without relying only on a basic distributor listing.

Devis Contact
TUSB2070PT - 7-Port USB 1.0 Hub Controller | Texas Instruments
TUSB2070PT

TUSB2070PT - 7-Port USB 1.0 Hub Controller | Texas Instruments

The Texas Instruments TUSB2070PT is a CMOS 7-port USB hub controller that conforms to USB Specification Version 1.0, supplied in a 48-pin LQFP (PT) surface-mount package with a 0 °C to +70 °C commercial operating temperature range. According to the manufacturer datasheet, the device provides up to seven downstream ports from a single upstream connection, consolidating multiple legacy USB peripherals behind one host port. A USB hub controller is a type of USB interface controller: it sits between a host and one or more downstream devices, managing enumeration, power distribution, and data traffic across the bus. In the product-type hierarchy, a USB hub controller belongs to interface controllers, which are a subset of integrated circuits used for signal and protocol bridging. In an end system, the hub controller provides the physical fan-out layer between a single USB port and several peripherals, sitting below the host controller and above the physical USB transceiver layer. Key characteristics of the TUSB2070PT include support for up to seven downstream ports, full-speed operation under USB Specification 1.0 rules, a monolithic CMOS implementation, and a single upstream port connection for the host link. The 48-pin LQFP (PT) body gives generous pin count for port-level control and status signalling, while the industrial-temperature 0 °C to +70 °C range suits commercial and light-industrial equipment. Detailed electrical ratings such as supply voltage, I/O current, and internal oscillator tolerance are not stated in the retrieved data and must be confirmed against the manufacturer datasheet. Architecturally, the device implements the split-transaction, single-master USB 1.0 protocol stack internally, including host-controller interface signalling toward the upstream port and per-port transceiver interfacing toward downstream ports. It is a legacy architecture: modern designs normally use USB 2.0 high-speed hubs with integrated PHY and charge-pump regulators, so the TUSB2070 remains most relevant where a legacy USB 1.0 host must be expanded without changing the upstream device class. Typical uses include legacy personal-computer and embedded host systems needing additional full-speed USB ports, industrial data-acquisition panels, point-of-sale and print peripherals, and test benches that replicate USB 1.0 topologies. Because it is an established, widely supported part with a long service history, it is frequently found in repair and legacy-platform maintenance programs. Two design considerations matter most. First, the device is no longer the newest Texas Instruments 7-port hub: the manufacturer lists the TUSB2077A, also in a 48-LQFP package, as the replacement, so new designs should start there. Second, a 48-LQFP body demands careful decoupling and ground-plane continuity to keep USB signal integrity within the 1.0 specification budget. This page consolidates distributor availability signals, a drop-in replacement analysis for the 48-LQFP 7-port hub footprint, lifecycle guidance, and practical design notes that are not gathered together in a single manufacturer datasheet.

Devis Contact
TUSB2077APT - 7-Port USB 2.0 Hub Controller | Texas Instruments
TUSB2077APT

TUSB2077APT - 7-Port USB 2.0 Hub Controller | Texas Instruments

The Texas Instruments TUSB2077APT is a seven-port Universal Serial Bus hub controller operating as a full-speed USB 2.0 device at 12 Mbps. The controller is offered in a 48-pin LQFP package with a 7 mm by 7 mm body. It integrates USB hub logic with an optional serial EEPROM interface for product identification and configurable USB descriptors. A USB hub controller is an interface semiconductor that manages one upstream USB connection and multiple downstream ports. In the broader hierarchy, the TUSB2077APT belongs to the USB interface controller class, within interface integrated circuits and general-purpose semiconductor devices. Its seven-port architecture allows several USB peripherals to share one host controller while individual downstream connections can be enabled, disabled, or managed for power and enumeration requirements. The manufacturer identifies the TUSB2077APT as a seven-port full-speed USB 2.0 hub controller. It supports both bus-powered and self-powered operating modes, which allows the hub to be designed around the power budget of a host device or with a dedicated external supply. The optional serial EEPROM interface provides a path for storing descriptor information rather than relying only on the controller's default descriptor behavior. The EXTMEM control is connected to pin 47 and determines whether the optional EEPROM interface is enabled. According to the Texas Instruments TUSB2077A product page, driving EXTMEM high enables the optional EEPROM function and causes the vendor and product identifiers to use defaults, including enumeration as a General Purpose USB Hub. This makes EXTMEM an important PCB-level design and firmware-configuration decision. Typical uses include compact USB expansion products, computer peripherals, docking equipment, industrial control panels, test systems, and embedded systems that need several full-speed USB connections. A design must allocate upstream and downstream signal routing, verify power-source requirements, and configure the hub for either bus-powered or self-powered operation. The optional EEPROM path should be assessed early because its presence or absence affects descriptor customization and board population. Use the manufacturer pin-description table and package drawing when assigning all 48 pins and laying out the LQFP footprint. The downstream data paths require careful, impedance-conscious routing, while power and ground connections need enough copper area to support the selected operating mode. Designers should also confirm the configuration of EXTMEM at pin 47 and the intended behavior of the optional EEPROM interface. This product record combines the manufacturer's hub-function details, package and pin-count information, lifecycle information, sourcing context, and a conservative drop-in comparison. It also identifies practical design decisions that are easy to overlook: descriptor customization, EXTMEM configuration, power-mode selection, and validation of every candidate replacement before PCB substitution.

Devis Contact
TUSB2077APTR - 7-Port USB 2.0 Hub Controller | Texas Instruments (Tape & Reel)
TUSB2077APTR

TUSB2077APTR - 7-Port USB 2.0 Hub Controller | Texas Instruments (Tape & Reel)

The Texas Instruments TUSB2077APTR is a seven-port Universal Serial Bus hub controller operating as a full-speed USB 2.0 device at 12 Mbps. The controller is offered in a 48-pin LQFP package with a 7 mm by 7 mm body. It integrates USB hub logic with an optional serial EEPROM interface for product identification and configurable USB descriptors. A USB hub controller is an interface semiconductor that manages one upstream USB connection and multiple downstream ports. In the broader hierarchy, the TUSB2077APTR belongs to the USB interface controller class, within interface integrated circuits and general-purpose semiconductor devices. Its seven-port architecture allows several USB peripherals to share one host controller while individual downstream connections can be enabled, disabled, or managed for power and enumeration requirements. The manufacturer identifies the TUSB2077APTR as a seven-port full-speed USB 2.0 hub controller. It supports both bus-powered and self-powered operating modes, which allows the hub to be designed around the power budget of a host device or with a dedicated external supply. The optional serial EEPROM interface provides a path for storing descriptor information rather than relying only on the controller's default descriptor behavior. The EXTMEM control is connected to pin 47 and determines whether the optional EEPROM interface is enabled. According to the Texas Instruments TUSB2077A product page, driving EXTMEM high enables the optional EEPROM function and causes the vendor and product identifiers to use defaults, including enumeration as a General Purpose USB Hub. This makes EXTMEM an important PCB-level design and firmware-configuration decision. Typical uses include compact USB expansion products, computer peripherals, docking equipment, industrial control panels, test systems, and embedded systems that need several full-speed USB connections. A design must allocate upstream and downstream signal routing, verify power-source requirements, and configure the hub for either bus-powered or self-powered operation. The optional EEPROM path should be assessed early because its presence or absence affects descriptor customization and board population. Use the manufacturer pin-description table and package drawing when assigning all 48 pins and laying out the LQFP footprint. The downstream data paths require careful, impedance-conscious routing, while power and ground connections need enough copper area to support the selected operating mode. Designers should also confirm the configuration of EXTMEM at pin 47 and the intended behavior of the optional EEPROM interface. This product record combines the manufacturer's hub-function details, package and pin-count information, lifecycle information, sourcing context, and a conservative drop-in comparison. It also identifies practical design decisions that are easy to overlook: descriptor customization, EXTMEM configuration, power-mode selection, and validation of every candidate replacement before PCB substitution.

Devis Contact
TUSB211RWBR - 480 Mbps USB 2.0 Signal Conditioner | TI
TUSB211RWBR

TUSB211RWBR - 480 Mbps USB 2.0 Signal Conditioner | TI

Texas Instruments TUSB211RWBR is a USB 2.0 high-speed signal conditioner designed to compensate for intersymbol interference in USB transmission channels. The device supports USB high-speed operation at 480 Mbps and is offered in a 12-pin X2QFN package measuring 1.6 mm by 1.6 mm. Its compact footprint makes the TUSB211 suitable for USB ports, cable extensions, peripheral connections, and embedded systems where signal loss can impair data integrity. A USB high-speed signal conditioner is an interface device placed within a USB 2.0 data path to improve signal quality across lossy interconnects. USB high-speed signaling uses differential data lines with significant bandwidth requirements, making cable length, connector transitions, PCB routing, and impedance discontinuities important system-level considerations. The TUSB211 belongs to the broader hierarchy of signal-processing interface ICs, interface ICs, and semiconductor devices designed to preserve data integrity between hosts, hubs, and USB peripherals. The primary function of the TUSB211 is to restore a degraded differential signal by compensating for channel-induced loss and intersymbol interference. Its USB 2.0 high-speed capability permits operation at 480 Mbps, allowing a link to remain functional over channels that would otherwise suffer from reduced eye opening or communication errors. Because the signal-conditioning stage operates within the data path, placement and layout can determine how effectively it corrects the intended channel. The RWB ordering code identifies the compact 12-X2QFN configuration used by TUSB211RWBR. Its small surface-mount package supports high-density PCB layouts, although accurate placement requires careful attention to differential-pair geometry, ground-return paths, and decoupling. The manufacturer product information lists the device as a USB 2.0 480-Mbps high-speed signal conditioner and identifies TUSB211RWBR as a 12-pin RWB package variant. Typical uses include USB host-to-peripheral links, USB-to-wireless bridges, industrial USB connections, peripheral docking systems, and cable-extension designs. The device is especially relevant when a connector, cable, or long PCB route introduces measurable high-speed attenuation and the designer wants to recover usable eye margin without replacing the entire USB interface implementation. When laying out a design, treat the conditioner as part of the high-speed channel rather than as an isolated IC. Verify differential impedance, minimize impedance discontinuities, provide the required local bypassing, and place the device where the channel losses remain predictable. Confirm signal-eye and compliance behavior with the complete connector, cable, host, and peripheral combination because channel length and topology can change the amount of correction required. This product page combines the exact TUSB211RWBR ordering information with practical USB signal-integrity guidance, compatibility-focused alternatives, and a side-by-side view of the electrical and packaging constraints that determine whether a substitution can be implemented without a PCB redesign.

Devis Contact