Produits (44 000+)

ICS512MI - 160MHz PLL Clock Multiplier | Renesas Electronics
ICS512MI

ICS512MI - 160MHz PLL Clock Multiplier | Renesas Electronics

Renesas Electronics ICS512MI is a single PLL clock-multiplier clock generator with a maximum output frequency of 160 MHz, supplied in an 8-pin SOIC package. It accepts a clock or crystal input, provides bypass operation, and uses CMOS output circuitry. These characteristics position the ICS512MI in the clock and timing hierarchy as a phase-locked-loop clock generator rather than a conventional fixed-frequency oscillator. A PLL clock multiplier is a timing IC that derives one or more stable clock outputs from a lower-frequency reference. Its phase-locked loop compares the reference with an internal feedback signal and adjusts the generated output to maintain phase and frequency relationships. In the ICS512MI, the input can be a clock signal or crystal, while PLL bypass allows the system to select a direct clock path when required. This combination supports frequency conversion and clock distribution in computing, networking, communication, and industrial systems. Principal features include a maximum clock frequency of 160 MHz, one clock-generation circuit, CMOS output, PLL capability with bypass, and a stated input-to-output ratio of 1:2. The 8-pin SOIC package provides a compact surface-mount form factor suitable for conventional PCB assembly. The device is positioned as a low-cost oscillator alternative when a system needs a high-quality multiplied clock or reference clock derived from a lower-frequency source. Technically, the important design consideration is that the reference source, loop behavior, output stability, and bypass mode must all be evaluated as one clock-generation system. A crystal-connected design provides a stable reference, while an externally driven clock offers flexibility in systems that already have a reference available. The bypass path should be evaluated for startup sequencing, glitch behavior, and output-source transitions using the manufacturer’s recommended circuit and timing information. Typical uses include processor and peripheral clock generation, communication-system reference clocks, network-interface timing, industrial control modules, and general-purpose frequency multiplication. The ICS512MI can be especially useful where replacing a higher-cost crystal oscillator with a programmable PLL-based clock source simplifies board-level frequency planning. When laying out a PCB, route the input, feedback, ground, and clock-output paths with attention to return paths and switching-edge behavior. Follow the manufacturer datasheet for recommended crystal-load components, decoupling, grounding, and maximum operating conditions. Validate timing margin in the assembled system rather than relying only on nominal frequency figures. This page combines the ICS512MI specifications, package details, practical clock-design guidance, and clearly qualified replacement information to support faster engineering evaluation and sourcing.

Devis Contact
ICS512MIT - 160MHz PLL Clock Generator | Renesas Electronics
ICS512MIT

ICS512MIT - 160MHz PLL Clock Generator | Renesas Electronics

Renesas Electronics ICS512MIT is a 160MHz PLL clock generator IC with one CMOS output, clock or crystal input, and an 8-SOIC package measuring 0.154 inch or 3.90mm in width. The device is designed to generate a high-quality high-frequency clock output and a reference clock from a lower-frequency crystal or clock input using phase-locked-loop techniques. A PLL clock generator is a timing IC that multiplies or synthesizes a clock frequency while providing a stable reference for digital and analog systems. The ICS512 belongs to the clock and timing hierarchy within integrated circuits, where it functions as a frequency multiplier and clock source. Its low-cost oscillator architecture is intended to replace conventional crystal oscillators in many electronic systems. Key features include a maximum operating frequency of 160MHz, one clock or crystal input, one CMOS output, and PLL operation with bypass capability. The input-to-output ratio listed for the device is 1:2, allowing a lower-frequency reference to generate a higher-frequency clock. The operating supply range is 3V to 5V, and the specified operating temperature range is -40°C to +85°C. The PLL-based architecture uses a standard fundamental-mode crystal to establish a stable reference, then multiplies that reference to generate the requested output clock. Bypass mode provides a practical path for clock distribution or test configurations. The CMOS output is suited to digital logic, communication equipment, consumer electronics, and embedded systems requiring a centralized clock source. Typical applications include digital controller boards, communication modules, industrial control equipment, test and measurement systems, and embedded products that require a multiplied clock or reference signal. The 8-SOIC surface-mount package supports compact board layouts while keeping assembly compatible with conventional SOIC-8 footprint practices. Designers should confirm the crystal frequency, PLL ratio, output waveform, load capacitance, and bypass configuration against the manufacturer application guidance. Decoupling capacitors should be placed close to the supply and ground pins, and clock traces should be routed with controlled impedance and minimized loading. This product page combines the manufacturer specifications, package information, lifecycle status, practical design notes, and sourcing guidance for engineers evaluating the ICS512MIT as an obsolete clock-generation component or replacement candidate.

Devis Contact
ICS512MT - 200MHz LOCO PLL Clock Multiplier | Renesas | 8-SOIC
ICS512MT

ICS512MT - 200MHz LOCO PLL Clock Multiplier | Renesas | 8-SOIC

The Renesas Electronics ICS512MT is a LOCO PLL clock multiplier and clock generator IC that multiplies a low-frequency crystal or external clock reference up to a maximum output frequency of 200 MHz at a 1:2 multiply ratio, housed in an 8-pin SOIC package with a 0.154 inch (3.90 mm) body width. It accepts a clock or crystal oscillator input, drives CMOS clock outputs, and includes a bypass path so the PLL can be disabled when a direct reference clock is preferred. A clock multiplier is a phase-locked loop (PLL) based timing device that takes a low-cost, low-frequency reference source - typically a crystal oscillator running between 2 MHz and 50 MHz - and synthesises a much higher, phase-locked output frequency. In the product hierarchy, a clock multiplier sits under clock generator ICs, inside clock and timing ICs, within integrated circuits, and ultimately falls under the broader timing and clocking element of any digital or RF system. Its purpose is to deliver high-quality, stable, jitter-controlled timing from an inexpensive reference. Key features of the ICS512MT include a PLL with bypass capability, a maximum output frequency of 200 MHz, a 1:2 input-to-output ratio, CMOS output signalling, and a single clocking circuit on board. The bypass mode allows the same board to be used in test or low-power configurations where the PLL lock time or power consumption is undesirable. Because the part is a multiplier rather than a general-purpose fractional-N synthesiser, the design is simpler, cheaper, and typically lower in phase noise than a programmable synthesizer of comparable output rate. Technically the ICS512MT uses a phase-locked loop that compares a divided output against the reference input and continuously corrects the internal voltage-controlled oscillator until the multiplier ratio is satisfied. Locking behaviour, reference-to-output jitter, output drive strength, and supply requirements are governed by the manufacturer datasheet, which should be consulted for absolute maximum ratings, recommended decoupling, and crystal load-capacitance selection. Typical uses include telecommunications line-card and base-station clocking, networking equipment clock synthesis, instrumentation and test-and-measurement front ends, industrial control and data acquisition systems, and any board that must convert a modest-frequency oscillator into a 200 MHz domain clock for high-speed serial links or ADC/DAC sampling systems. When designing around this device, pay particular attention to reference jitter and loop bandwidth: a crystal reference with excessive phase noise will multiply that noise by the same ratio at the output, and a noisy reference cannot be corrected downstream. Keep supply decoupling tight and route the crystal or reference input away from high-current switching nodes to preserve the low-jitter behaviour the LOCO architecture is intended to deliver. This page consolidates the device specification, family drop-in options in the same SOIC-8 footprint, comparison tables and practical design notes, giving an engineer the decision context that a bare distributor listing does not.

Devis Contact
ICS513M - 140MHz LOCO PLL Clock Generator | Renesas
ICS513M

ICS513M - 140MHz LOCO PLL Clock Generator | Renesas

The Renesas ICS513M is a LOCO PLL clock generator and fanout distributor with a maximum output frequency of 140 MHz, one clock circuit, CMOS output, and an 8-pin SOIC package. It accepts a crystal or external clock input and includes PLL bypass functionality, allowing it to generate a high-quality clock from a 14.31818 MHz crystal or clock source. The 1:2 input-to-output ratio reported in the verified product data supports clock multiplication use where a higher-frequency CMOS clock is required. A PLL clock generator is a clock-and-timing semiconductor that locks an internal phase-locked loop to a reference oscillator and multiplies or redistributes that reference into one or more stable digital clock outputs. In the product hierarchy, a PLL clock generator belongs to clock generation and distribution, then clock and timing ICs, then broader semiconductor and digital IC categories. It is used where a circuit requires a controlled relationship between a low-frequency crystal reference and a higher-frequency operating clock. The ICS513M's principal verified features include a 140 MHz maximum operating frequency, CMOS output logic, one clock circuit, support for both crystal and clock inputs, and PLL bypass capability. Its 8-SOIC package measures 3.90 mm in width according to the distributor listing. The 1:2 input-to-output ratio makes the device relevant to systems that need frequency multiplication from a standard 14.31818 MHz reference. Technically, the ICS513M combines reference generation with phase-locked-loop multiplication and clock distribution. The verified descriptions characterize it as a cost-effective way to produce a high-quality, high-frequency clock output. PLL bypass provides a selectable operating mode for designs that require direct reference-clock behavior rather than multiplied output, although the supplied data does not specify bypass propagation delay, jitter, lock time, or loop bandwidth. Typical uses include digital logic timing, communication equipment, embedded processing, and general-purpose clock distribution where a crystal or external clock is available. The ICS513M can be used as a clock source for circuits requiring a CMOS-compatible, multiplied clock derived from 14.31818 MHz. Its single-circuit fanout structure is appropriate for designs that need one primary high-frequency clock rather than multiple independently programmable outputs. When implementing the ICS513M, verify the crystal load capacitance, feedback-divider configuration, operating voltage, and output timing against the manufacturer datasheet. The verified snippets do not provide supply-voltage limits, output rise or fall times, phase jitter, RMS period jitter, or cycle-to-cycle jitter. Those timing and electrical details should be confirmed before using the device as a direct replacement for a different PLL generator. This page consolidates the verified distributor specifications, genuine source links, application guidance, and same-family replacement candidates. It also distinguishes confirmed ICS513M parameters from unavailable electrical and timing data so engineers can make a traceable component-selection decision rather than treating unsupported values as guaranteed specifications.

Devis Contact
ICS513MLF - 140MHz Clock Generator | Renesas Electronics
ICS513MLF

ICS513MLF - 140MHz Clock Generator | Renesas Electronics

Renesas Electronics ICS513MLF is a LOCO PLL clock-generator and fanout distribution IC rated to 140 MHz, with one clock output in an 8-pin SOIC package measuring 0.154 inches wide and 3.90 mm. It operates from a 4.5 V to 5.5 V supply and uses CMOS-compatible interfaces. The device is designed to generate a stable, high-quality clock from a 14.31818 MHz crystal or external clock input. A PLL clock generator is a clock-timing semiconductor that multiplies a reference frequency and distributes the resulting clock to digital circuits. A crystal reference provides a stable time base, while the internal phase-locked loop derives the required output frequency. Clock-generator ICs belong to the clock and timing hierarchy, where they sit between frequency references and the clocks consumed by processors, communications equipment, and digital logic. ICS513MLF combines a 140 MHz maximum stated operating frequency with a single clock output and a 5 V supply range. Its LOCO positioning emphasizes a cost-effective implementation for common digital clocking needs. The lead-free 8-SOIC package supports conventional surface-mount assembly and is suitable for compact industrial, communications, and embedded systems that need a local clock source without employing a more complex high-performance frequency synthesizer. The device operates with CMOS-compatible signals and can use either a 14.31818 MHz crystal or a clock input as its frequency reference. During implementation, the crystal, load capacitance, supply decoupling, and output-drive configuration determine whether the generated clock meets the timing and jitter requirements of the downstream circuit. The manufacturer datasheet should be consulted for the exact reference configuration and electrical limits before finalizing a high-speed design. Typical uses include clocking digital controllers, standardizing clock distribution across a compact circuit board, and replacing a board-level oscillator plus divider arrangement with a single timing IC. The single-output configuration is especially appropriate when only one derived clock is needed. In multi-domain equipment, the ICS513MLF can supply a common local clock where clock quality and frequency are adequate but multi-output fanout or differential clocking is not required. PCB implementation requires short return paths and careful treatment of the crystal and high-speed clock traces. Place the reference components close to the device, connect the supply to a low-impedance ground plane, and route clock outputs away from noisy switching nodes. Verify output rise time, duty cycle, jitter, and load capacitance in the finished layout because the complete timing performance depends on component selection and board implementation. This page combines the identified electrical ratings, package details, sourcing guidance, and application-oriented design considerations for ICS513MLF. It also distinguishes the device from related clock-generator references while clearly identifying parameters that require confirmation against the manufacturer datasheet before production release.

Devis Contact
ICS513MT - 140MHz PLL Clock Generator | Renesas Electronics
ICS513MT

ICS513MT - 140MHz PLL Clock Generator | Renesas Electronics

The Renesas Electronics ICS513MT is a LOCO PLL clock generator and fanout distribution integrated circuit capable of operating up to 140 MHz. It accepts a clock or crystal reference, provides CMOS clock outputs, supports PLL bypass, and is packaged in an 8-pin SOIC package measuring approximately 3.90 mm wide. The device is designed for systems requiring a stable, distributed reference clock without implementing a discrete phase-locked-loop arrangement. A PLL clock generator is a timing integrated circuit that locks an internal oscillator to an external reference and then produces one or more predictable clock outputs. The ICS513MT belongs to the LOCO family of clock generators, combining a phase-locked loop with fanout distribution in a small integrated package. Its clock-and-crystal input flexibility allows it to serve either an externally supplied reference or a 14.31818 MHz crystal, depending on the system architecture. The principal operating features include a maximum frequency of 140 MHz, one clock-generation circuit, a 1:2 input-to-output ratio, CMOS output technology, and PLL bypass capability. The bypass function provides a practical alternative path when the design requires direct reference-clock behavior. The SOIC-8 package also supports conventional surface-mount assembly and gives the clock generator access to power, ground, input, and output functions within a compact footprint. Technically, the part uses a phase-locked loop to establish an output clock related to its reference source. Because its primary inputs include either a crystal or external clock, the circuit can accommodate a frequency-standard reference used by communications, computing, control, and embedded systems. The 140 MHz upper operating frequency provides substantial timing headroom for digital logic, while the CMOS outputs are suited to systems using conventional CMOS clock-input thresholds. Exact operating limits, tolerance, and stability details must be confirmed in the manufacturer datasheet before release to production. Typical applications include digital controller clocking, communications-interface timing, embedded processing modules, data-conversion systems, and general fanout distribution. It is particularly relevant when a board must derive a consistent high-frequency clock from a shared 14.31818 MHz reference while maintaining a compact surface-mount layout. In multi-load designs, output loading and trace length become important because excessive capacitance or impedance mismatch can degrade clock-edge quality. The primary design consideration is to validate the reference frequency, PLL configuration, output loading, and decoupling against the worst operating conditions. Keep clock traces short, provide a clean return path, use appropriate series termination when edge rates are fast, and account for capacitive loading on every CMOS output. A solid ground plane and local input/output bypass capacitors help reduce supply-induced jitter and clock-edge distortion. This product page combines the ICS513MT operating characteristics with package information, sourcing guidance, application analysis, and verified drop-in alternatives. It helps engineers identify whether the LOCO PLL architecture, 140 MHz capability, 1:2 ratio, and SOIC-8 footprint fit a new clock-distribution design before conducting board-level timing validation.

Devis Contact
ICS514M - 140MHz PLL Clock Generator | Renesas | 8-SOIC
ICS514M

ICS514M - 140MHz PLL Clock Generator | Renesas | 8-SOIC

Renesas Electronics ICS514M is a 140MHz clock generator and fanout-distribution IC that uses a phase-locked loop to multiply a 14.31818MHz crystal or clock reference. It is packaged in an 8-pin SOIC measuring 3.90mm wide and operates from a 3V to 5.5V supply in the commercial 0°C to 70°C temperature range. A clock generator is a timing IC that converts a stable low-frequency reference into one or more higher-frequency clock signals. Clock generators and fanout-distribution devices form part of the broader clock and timing IC category, supporting clock synthesis, distribution, and system timing in digital equipment. The ICS514M uses PLL multiplication to provide a practical alternative to selecting and sourcing a high-frequency crystal for every clocked circuit. The device supports a 14.31818MHz crystal or clock input and reaches a maximum output frequency of 140MHz. Its configurable S1 and S0 input pins provide operating-state control referenced in the datasheet: when S1 and S0 are both low, the internal PLL is disabled, the CLK output remains low, and the crystal oscillator and REF output remain active. This permits a system to retain reference-clock availability while suppressing the divided or multiplied clock output. The 8-pin surface-mount SOIC package supports compact clock-generation layouts in industrial, communications, consumer, and embedded equipment. Operating from 3V to 5.5V makes the device usable with both 3.3V and 5V system rails, although the complete external crystal, load-capacitor, and output-loading design must be evaluated against the manufacturer datasheet. Its maximum 140MHz rating is a key selection criterion for processors, programmable logic, communications equipment, and digital peripherals requiring a multiplied reference. A primary design consideration is that PLL programming, crystal accuracy, load capacitance, output jitter, and allowable operating modes must be checked before layout release. Decoupling capacitors should be placed close to the supply pins, and clock traces should be routed with controlled impedance and short return paths to minimize noise pickup and crosstalk. The stated 140MHz maximum should not be treated as guaranteed performance for every crystal and output-divider configuration. This product page consolidates the verified manufacturer and distributor information, provides engineering-oriented selection guidance, identifies same-footprint alternatives, and highlights design details that help buyers compare ICS514M clock generators more efficiently than a basic distributor listing alone.

Devis Contact
ICS514MT - 140MHz Loco PLL Clock Generator | Renesas
ICS514MT

ICS514MT - 140MHz Loco PLL Clock Generator | Renesas

Renesas Electronics ICS514MT is a Loco PLL clock generator with a maximum operating frequency of 140 MHz, CMOS output, and support for either a 14.31818 MHz crystal or an external clock input. The device is packaged in an 8-SOIC package measuring 0.154 inch, or 3.90 mm, in width. Its PLL includes a bypass function, allowing it to support both synthesized and bypassed clock-generation paths. A PLL clock generator is a timing integrated circuit that multiplies, divides, or conditions an input clock to produce one or more stable output frequencies. In the broader semiconductor hierarchy, the ICS514MT belongs to the clock and timing IC family, where PLLs are used alongside oscillators, dividers, buffers, and clock trees to distribute timing signals throughout electronic systems. Its LOCO architecture is intended to provide an economical frequency-generation solution from a common crystal reference. The ICS514MT accepts a clock or crystal input and produces a CMOS clock output. Its maximum frequency is 140 MHz, and its input-to-output ratio is listed as 1:2. The PLL and bypass functions give designers the option to retain a direct source-clock path or use phase-locked synthesis. These features are useful where a system needs more than one frequency domain but only a small number of clocks. The single-circuit architecture keeps the design focused on one principal clock-generation function. A crystal-based implementation can use the specified 14.31818 MHz reference, while an external clock input offers flexibility when another oscillator already provides a suitable reference. Because the output technology is CMOS, the device is intended to interface with digital logic operating at compatible voltage levels, subject to the operating limits and supply requirements defined in the manufacturer datasheet. Typical uses include communications equipment, digital signal-processing systems, embedded-control platforms, frequency-sensitive test equipment, and general-purpose digital subsystems. In a communications design, the part can create a stable high-frequency operating clock for a synthesizer, controller, or data-conversion chain. In test equipment, it can provide a repeatable reference for timing-sensitive measurement or processing sections. PCB implementation should preserve short clock paths and suitable return paths to minimize susceptibility to noise and crosstalk. Place the crystal, input circuitry, decoupling capacitors, and output load close to the device where the layout guidance permits. Check the bypass-mode state before system startup so that the intended clock path is established consistently. This product overview combines the ICS514MT device classification, operating limits, package information, drop-in replacement evidence, and application guidance into one engineering reference. It also identifies design checks that are important beyond the basic 140 MHz headline specification, including PLL bypass behavior, source selection, clock routing, and package-level decoupling.

Devis Contact
ICS525-01R - 160MHz User-Configurable Clock | Renesas
ICS525-01R

ICS525-01R - 160MHz User-Configurable Clock | Renesas

The Renesas ICS525-01R is a user-configurable clock generator and fanout distribution IC with a maximum output frequency of 160 MHz, housed in a 28-pin SSOP package measuring 0.154 inch (3.90 mm) wide. The device is designed to replace discrete crystal-oscillator arrangements in systems where multiple logic domains require accurate, mutually related clock signals. A user-configurable clock, commonly called OSCaR, is a clock-generation IC whose output configuration is established with hardware select pins rather than a fixed factory divider ratio. The ICS525-01/02 family accepts a crystal or clock input and can generate nearly any supported output frequency from that source. Grounding or floating the configuration pins selects the required operating mode, making the ICS525-01R useful where the design must be adjusted without changing external components. Key features include a 160 MHz maximum output frequency, single-clock fanout capability, configuration through select pins, and operation from either a crystal or an external clock source. The 150 mil-body, 28-pin SSOP construction provides enough routing flexibility for a clock tree while remaining compatible with established surface-mount assembly methods. The -01R ordering suffix identifies the 160 MHz configuration within the ICS525 family. The ICS525-01R is part of the ICS525-01/02 family, whose architecture replaces a conventional crystal oscillator plus a separate divider or fanout arrangement with one configurable clock circuit. Its select-pin control allows a board designer to define the clock relationship required by processors, transceivers, converters, and data-conversion equipment. This integration reduces the number of discrete timing components while preserving accurate frequency relationships across the system. Typical uses include retrofitting a clock into an existing board, generating related clocks for multiple digital loads, supporting communication interfaces, and producing clocks for converters or test equipment. Because the family supports both crystal and external-clock drive, the device can suit new designs and legacy repairs where an original oscillator configuration is difficult to source. When assigning a replacement, confirm the selected frequency table, input-source arrangement, and output configuration against the board's original design. Place the clock source and decoupling close to the device, and route clock outputs as short, controlled-impedance traces. The select pins must be left grounded or floating as specified by the configuration table; do not add pull-up or pull-down resistors unless the board design requires them. This page adds practical configuration guidance, verified package and frequency information, a drop-in comparison, and sourcing guidance to the basic manufacturer datasheet information, helping engineers evaluate the ICS525-01R for both new designs and legacy clock-tree repairs.

Devis Contact
ICS525R-02 - 250MHz Configurable Clock Generator | Renesas
ICS525R-02

ICS525R-02 - 250MHz Configurable Clock Generator | Renesas

Renesas Electronics ICS525R-02 is a user-configurable clock generator and fanout distribution IC operating to 250 MHz and packaged in a 28-pin SSOP. The device accepts a crystal or clock input and uses a phase-locked loop to generate configurable high-frequency clock outputs, providing a compact clock-tree solution for digital systems that require multiple related frequencies from one reference. A configurable clock generator is a timing IC that combines a phase-locked loop, programmable frequency synthesis, and output distribution. In the product hierarchy, it belongs to clock and timing ICs and provides a bridge between a stable crystal or external reference and multiple clock domains. The OSCaR family is specifically designed to replace conventional crystal-oscillator arrangements in systems that need programmable frequency selection rather than one fixed output frequency. The ICS525R-02 supports a maximum output frequency of 250 MHz and includes PLL bypass functionality. Its user-configurable architecture permits engineers to select operating combinations of the voltage-controlled oscillator, reference frequency, and output dividers. The 28-pin SSOP has a 0.154-inch, 3.90 mm body width and integrates clock generation, fanout distribution, and programmable divider resources into one package. The PLL-based architecture provides a practical alternative to designing a fixed-frequency oscillator and separate divider or buffer networks. Bypass operation allows the device to be evaluated and integrated with an external clock path, while PLL operation supports synthesized outputs from a crystal or clock source. Exact divider ratios, VCO limits, jitter, output levels, and recommended crystal parameters should be selected using the configuration tables in the manufacturer datasheet. Typical uses include network-interface clock distribution, processor and FPGA clock trees, telecommunications timing, digital test equipment, and industrial control systems. The device is especially useful where several logic domains must be related to one frequency reference but cannot all use a simple fixed crystal oscillator. Short traces, terminated clock routing, and careful separation from high-speed data paths remain essential at the upper operating frequency. For implementation, evaluate every possible VCO, reference, and output-divider combination before committing to the PCB. Confirm the selected output frequency, duty-cycle tolerance, jitter requirement, crystal load capacitance, and I/O voltage against the manufacturer configuration guide. The SSOP footprint also requires assembly planning for its 0.154-inch body width and adequate lead-clearance spacing. This product record combines the device function, verified 250 MHz operating point, package information, configuration guidance, and practical replacement considerations. It is intended to help engineers identify whether the ICS525R-02 matches the required clock architecture before moving to a detailed design review.

Devis Contact
ICS525R-04 - 200MHz PECL Clock Generator | Renesas
ICS525R-04

ICS525R-04 - 200MHz PECL Clock Generator | Renesas

Renesas ICS525R-04 is a user-configurable clock generator that produces a high-quality differential PECL clock output up to 200 MHz. The device accepts a CMOS or crystal reference input, includes a PLL, and is packaged in a 28-pin SSOP. Its operating supply voltage is 4.5 V to 5.5 V. A clock generator is an integrated timing component that creates, conditions, and distributes a stable frequency reference through a system. The OSCaR family combines a phase-locked loop with selectable configuration pins, placing clock generation in the Clock & Timing IC category within the broader semiconductor and power-management ecosystem. Unlike a simple crystal oscillator, this architecture can support user-selectable output relationships and provide PECL-compatible differential outputs for high-speed digital circuitry. The ICS525R-04 supports a maximum operating frequency of 200 MHz and uses a PECL output interface. Configuration can be established through hardware-select pins rather than firmware or a device programmer, making the part useful where deterministic setup and minimal firmware support are priorities. The 4.5 V to 5.5 V supply range and SSOP-28 surface-mount package support established 5 V digital clocking systems. Internally, the OSCaR architecture uses a PLL to multiply or divide a crystal or external clock reference and generate the required output frequency. A PLL-based approach provides programmable frequency relationships while retaining a stable external reference. Differential PECL outputs are suited to short-reach, point-to-point interconnects where source-synchronous clocking, serializer/deserializer interfaces, or high-speed digital logic require low-skew clock distribution. Typical uses include telecommunications line cards, network-interface clock trees, high-speed serial links, test-and-measurement equipment, and industrial control systems. The same clock-generation approach can also support digital signal processors, FPGA clock planes, and communications processors when the system needs a locally generated PECL reference rather than a panel-distributed clock. When laying out the circuit, place the crystal and input decoupling close to the device and route differential outputs as a tightly matched pair with uninterrupted reference planes. The 28-pin SSOP footprint requires careful fanout because its narrow lead pitch can constrain escape routing on multilayer boards. Verify configuration-pin states during power-up and validate output frequency and duty-cycle behavior across the complete operating temperature range. This product record combines the oscillator function, principal electrical characteristics, package details, sourcing information, and practical implementation guidance in one engineering-focused reference. It also distinguishes verified device attributes from parameters that require confirmation from the manufacturer datasheet, helping designers move from component selection to a complete clock-tree design with fewer documentation gaps.

Devis Contact
ICS525R-11 User-Configurable Clock Generator | Renesas
ICS525R-11

ICS525R-11 User-Configurable Clock Generator | Renesas

Renesas Electronics ICS525R-11 is a user-configurable clock generator with a 40 MHz reference frequency and differential PECL clock outputs, supplied in a 28-pin SSOP surface-mount package. Its operating supply range is 3 V to 5.5 V, while clock-generator family documentation identifies 4.5 V to 5.5 V as a 5 V operating range for related ICS525R-11 variants. The device generates high-quality, high-accuracy clock outputs from an external crystal or clock source by configuring its select pins. A clock generator is a clock-and-timing integrated circuit that converts one reference source into one or more synchronized output frequencies. In the broader semiconductor hierarchy, the ICS525R-11 belongs to the clock generator and frequency synthesizer family, which supports microprocessors, programmable logic, network interfaces, communications equipment, and test systems. Its differential PECL outputs are suited to systems requiring a high-speed, low-noise clock rather than a conventional CMOS clock. The principal features are hardware-selectable configuration, a 40 MHz reference frequency, differential PECL clock generation, CMOS bus interfacing, and a 28-pin SSOP package. Grounding or floating the select pins allows the output frequency to be configured without firmware, software, or a device programmer. This makes the device useful where deterministic clock setup is preferred over programmable PLL control and where field configuration without a microcontroller is advantageous. Technically, the ICS525R-11 uses an inexpensive crystal or external clock as its frequency reference and derives a high-frequency differential output through the clock-generation architecture described for the ICS525 family. Differential signaling helps reduce susceptibility to common-mode noise on high-speed interconnects. Because the part is obsolete, existing installations can use it as a known-good supply source, but new designs should account for its limited product life-cycle availability. Typical applications include telecommunications and networking equipment, serial-interface clocking, FPGA or ASIC clock distribution, instrumentation, industrial control, and legacy data-acquisition systems. It is particularly appropriate when a fixed or selectable output frequency is needed, multiple dependent circuits require a coherent clock, and hardware-based configuration simplifies system startup. For PCB design, use the manufacturer pin-description table when assigning tracks, verify the selected-pin logic for the required output frequency, and provide clean reference-clock routing. Differential PECL traces should be routed as a matched pair with controlled impedance and short return paths to reduce edge degradation and jitter. This product summary consolidates electrical characteristics, package information, configuration details, lifecycle status, validated replacement information, and practical clock-routing guidance. It supports faster design review while preserving the distinction between confirmed device data and parameters that require confirmation from the manufacturer datasheet.

Devis Contact
ICS527R-01 - 160 MHz Zero-Delay Clock Slicer | Renesas
ICS527R-01

ICS527R-01 - 160 MHz Zero-Delay Clock Slicer | Renesas

The Renesas Electronics ICS527R-01 is a user-configurable zero-delay clock buffer and clock slicer with a 160 MHz operating frequency in a 28-SSOP package measuring 3.90 mm wide. It distributes a source clock across multiple outputs with matched propagation characteristics while allowing the user to generate multiplied or divided output-clock relationships from the input frequency. A clock slicer is a specialized timing integrated circuit that belongs to the clock and timing IC family, alongside clock buffers, generators, phase-locked loops, and frequency synthesizers. Its purpose is to control the relationship between an input clock and its outputs so that downstream circuits receive coherent, predictable timing references. The zero-delay architecture minimizes added latency between the source and fanout outputs, which is important when several subsystems must operate from the same clock domain. Key characteristics of the ICS527R-01 include a 160 MHz maximum clock frequency, a 28-SSOP package, zero-delay fanout operation, and user-programmable clock multiplication or division capabilities. The device is suited to systems that require more than one usable clock output without introducing uncontrolled skew between receiving circuits. Its configuration flexibility allows a single clocking component to serve systems whose operating modes require different output-clock relationships. The ICS527R-01 combines clock distribution with programmable ratio generation. Instead of cascading a separate divider or multiplier after a fanout buffer, the system can derive the required output relationships from one package. This reduces circuit count and keeps the clock-generation structure compact. Exact control-pin states, output ratios, supply voltage, and operating-temperature limits should be confirmed in the Renesas 527-01 datasheet before the device is placed in a new design. Typical uses include processor and peripheral clock distribution, telecommunications line-card timing, data-acquisition systems, test and measurement equipment, and industrial control modules. In a multi-channel data-conversion system, a common sliced clock can feed converters that must launch data against a shared time reference. In a telecommunications design, the fanout outputs can support separate transmit, receive, and processing sections that must remain synchronized. When laying out the PCB, keep clock traces short, use controlled-impedance routing where required, and avoid routing sensitive clock nets beside high-current switching nodes. Follow the package pin arrangement and recommended decoupling configuration in the manufacturer datasheet. Validate output ratio settings and startup behavior in hardware because incorrect control sequencing or an unsuitable input clock can produce invalid timing at downstream circuits. This page combines the verified product identity, package information, family-level functions, drop-in replacement options, application guidance, and engineering design notes in one engineering-focused reference.

Devis Contact
ICS527R-02 - 160MHz Zero-Delay Clock Slicer | Renesas
ICS527R-02

ICS527R-02 - 160MHz Zero-Delay Clock Slicer | Renesas

The Renesas Electronics ICS527R-02 is a user-configurable clock slicer and zero-delay buffer with a maximum frequency of 160 MHz, one PECL input, and CMOS clock outputs, housed in a 28-SSOP package. It aligns the rising edges of PECLIN and FBIN according to divider ratios programmed by external reference and feedback components, allowing nearly any related output frequency to be generated from a PECL source clock. A clock slicer is a specialized timing IC that divides and recombines clock signals to provide adjustable phase relationships. Clock slicers sit within the clock and timing hierarchy as clock buffers and fanout devices, where low skew and predictable edge alignment are more important than simply regenerating a clock. The ICS527-02 family uses a PLL-based architecture to create zero-skew PECL-to-CMOS clocking relationships for communications, processor, and data-conversion systems. The ICS527R-02 supports a maximum operating frequency of 160 MHz and has one clock circuit. Its user-configurable reference and feedback dividers allow multiplication or division of the input clock, while the zero-delay architecture minimizes the skew between the relevant rising edges. PECL input support is useful in high-speed telecommunications and industrial clocking systems where the source clock is already distributed using ECL-family logic levels. Operationally, the device accepts a PECL reference clock and returns related CMOS clock outputs. The two CMOS outputs support fanout and clock distribution, reducing the need for separate logic buffers when several domains require the same derived timing signal. Zero-delay operation is intended for systems in which source and feedback clocks must be phase-aligned with very little edge displacement. Typical uses include telecom line-card clocking, data-converter clock generation, processor reference-clock distribution, network-interface timing, and industrial control systems. The 160 MHz ceiling makes the ICS527R-02 most appropriate for designs operating below that limit, while the 28-SSOP package supports compact, surface-mounted assemblies. PCB implementation requires careful treatment of high-speed clock inputs and outputs. Keep PECL traces short, provide a continuous reference plane, avoid stubs, and place termination and decoupling components close to the device. Confirm input/output timing, divider ratios, and supply sequencing against the manufacturer datasheet before releasing production artwork. This product page combines the manufacturer function description with package, frequency, interface, and architecture details, then adds application guidance, drop-in replacement limits, comparison parameters, and practical layout considerations. These engineering-oriented notes help distinguish a true PCB-compatible replacement from a merely similar clock-buffer product.

Devis Contact
ICS527R-03 - 160MHz Zero-Delay Clock Buffer | Renesas
ICS527R-03

ICS527R-03 - 160MHz Zero-Delay Clock Buffer | Renesas

Renesas Electronics ICS527R-03 is a 160 MHz zero-delay clock buffer and clock-distribution device packaged in a 28-SSOP surface-mount package. It is designed to reproduce an input clock through a low-latency buffer path and distribute that clock to downstream digital circuitry. The device is associated with user-configurable PECL input operation, while its low-voltage supply range is identified as 3.15 V to 3.45 V. The exact output configuration, skew, propagation delay, and input-referred noise are not stated in the available manufacturer listing. A zero-delay buffer is a clock-buffer IC that offers a very small propagation delay while providing buffering between a clock source and one or more receiving circuits. Clock buffers help isolate the source from downstream loading, reproduce the clock waveform with controlled edge relationships, and simplify distribution across multiple digital blocks. In the broader hierarchy, ICS527R-03 belongs to the clock and timing IC family, which includes clock buffers, clock slicers, clock generators, phase-locked loops, and frequency synthesizers. The main published specifications identify a maximum operating frequency of 160 MHz and use of a 28-SSOP package measuring 0.154 inch, or 3.90 mm, in width. The 3.15 V to 3.45 V operating-supply range supports low-voltage clocking systems. ICS527R-03 is also described as a fanout or distribution buffer with zero delay, a zero-skew clock-slicing function, and user-configurable PECL input behavior. These characteristics make the device relevant to processors, network interfaces, serializer or deserializer chains, test equipment, and other systems requiring a locally buffered clock. Clock integrity depends on preserving edge amplitude, rise and fall times, duty cycle, and inter-output timing relationships. A zero-delay architecture is valuable when one source must feed several destinations without allowing receiver input capacitance or board loading to disturb the original clock source. The available listing identifies one output in its abbreviated product description, but it does not expose the complete pin table, input configuration fields, output-enable logic, or detailed timing limits. Those details should be taken directly from the Renesas 527-03 datasheet before schematic capture. Typical uses include buffering a reference clock into a digital ASIC, distributing a communications clock between parallel processing sections, and regenerating a PECL-compatible clock within high-speed test and measurement systems. Because the ICS527R-03 operates from a narrow 3.3 V-class supply range, the input logic levels and downstream supply voltages must be compatible. Short, impedance-controlled clock traces and solid ground-plane return paths are important when preserving the 160 MHz operating capability. Designers should reserve the pins shown as control or configuration inputs for their required levels rather than treating unused clock-buffer pins as arbitrary no-connect locations. Termination, biasing, and decoupling depend on the selected PECL input configuration and the particular clock topology. The 28-SSOP footprint requires careful assembly planning because the fine-pitch package has a 3.90 mm body width and may be difficult to rework manually. This product page consolidates the exact package, frequency, voltage, lifecycle, and sourcing information visible for ICS527R-03 with application guidance, comparison considerations, and practical clock-layout notes. It also distinguishes the device from related 527-series variants and explains which electrical and pin-level details engineers must confirm in the manufacturer datasheet before releasing a production design.

Devis Contact
ICS527R-04 - 160MHz CMOS PLL Clock Driver | Renesas
ICS527R-04

ICS527R-04 - 160MHz CMOS PLL Clock Driver | Renesas

The Renesas Electronics ICS527R-04 is a user-configurable PECL-input, zero-delay-buffer clock driver based on a CMOS phase-locked loop, with a maximum operating frequency of 160 MHz. The device is associated with a 28-pin SSOP package and operates across a commercial temperature range of 0°C to 70°C. It belongs to the clock and timing hierarchy: PLL-based clock driver → clock buffer → clock and timing IC → semiconductor. A PLL-based clock driver is an integrated timing device that locks an output clock to a reference and distributes that clock through configurable logic paths. The user-configurable architecture allows a design to select the division ratio and output behavior required by the receiving circuitry. In a zero-delay-buffer configuration, the device minimizes propagation delay between the driving source and downstream clock loads while preserving a defined relationship between input and output edges. The ICS527R-04 supports a maximum frequency of 160 MHz, making it applicable to clock-generation and distribution systems operating below that limit. Its PECL input interface is intended for systems using positive emitter-coupled logic clock sources. The CMOS PLL implementation and configurable outputs provide the basis for translating a reference clock into multiple synchronized signals needed by digital logic, communications equipment, and test systems. A principal design consideration is the relationship between input frequency, selected feedback ratio, output division, and the resulting operating point. The manufacturer datasheet should be used to confirm supported configuration combinations, output-edge relationships, supply requirements, and the treatment of unused inputs or outputs before the device is placed into production. PCB implementation must preserve the pin assignments and decoupling recommendations associated with the SSOP-28 footprint. Typical uses include PECL-to-logic clock distribution, frequency multiplication or division within a PLL architecture, and generation of related clocks for digital subsystems. The device can also be used in communications equipment and test platforms where multiple outputs must remain synchronized. Its 0°C to 70°C commercial operating range is appropriate for indoor commercial and industrial equipment that does not require extended-temperature operation. Engineers should verify absolute maximum ratings, recommended operating conditions, AC timing, output-drive capability, and power consumption against the manufacturer datasheet before final schematic or layout release. The SSOP-28 package provides a high pin count relative to its body size, so careful routing and stable supply decoupling are particularly important. This page organizes the documented operating limits, package information, sourcing questions, and design considerations for ICS527R-04. It also distinguishes verified device facts from parameters that still require confirmation before a replacement or new design can be released.

Devis Contact
ICS542M - 156 MHz 1:2 Clock Divider | Renesas | SOIC-8
ICS542M

ICS542M - 156 MHz 1:2 Clock Divider | Renesas | SOIC-8

The Renesas Electronics ICS542M is a clock fanout buffer and programmable divider IC with a maximum input frequency of 156 MHz, supplied in an 8-pin SOIC package. It accepts a CMOS clock and provides divided outputs using selectable divide ratios of 2, 4, 6, 8, 12, or 16. Its 3 V to 5.5 V operating-supply range supports both 3.3 V and 5 V systems, while the 1:2 distribution function provides two clock outputs from one source. A clock divider is a timing IC that derives one or more lower-frequency or phase-related clock signals from an input reference. Within the broader clock and timing hierarchy, the ICS542M belongs to the clock-buffer, clock-distribution, and clock-divider category. This functionality is useful when a subsystem needs a divided reference clock, multiple outputs for parallel logic, or a lower-frequency signal generated without adding a separate oscillator and PLL. Key verified specifications include a maximum frequency of 156 MHz, a 1:2 output configuration, CMOS inputs, CMOS three-state outputs, and a 3 V to 5.5 V supply range. The listed divider ratios permit useful choices for digital clocking, data converters, communications modules, and embedded systems. The package designation is 8-SOIC with a stated width of 0.154 inches, or 3.90 mm. The ICS542M combines clock division and distribution in one device. The divide control selects the relationship between the input clock and the generated outputs, while the fanout section supports distribution to two destinations. This integration can reduce the number of separate timing components required when only one of the available divide ratios is needed. Because the verified product information does not include detailed propagation-delay, output-duty-cycle, rise-time, fall-time, or jitter values, those characteristics should be checked in the current Renesas datasheet before high-speed timing closure. Typical uses include clock distribution for digital logic, generating a divided reference for data-acquisition systems, supporting communications equipment, and producing deterministic clocks in embedded control platforms. The 156 MHz ceiling accommodates demanding CMOS clock trees, but actual system operation must account for supply voltage, temperature, load capacitance, and the selected divider ratio. For layout, place the device close to the clock source and receiving circuits to minimize trace length and propagation-delay variation. Keep output traces short, provide the decoupling specified by the manufacturer datasheet, and use controlled-impedance routing when outputs drive longer PCB traces. Verify unused-output state, enable or three-state behavior, and rise/fall-time requirements in the system timing budget. This page consolidates the verified Renesas and distributor information, lifecycle evidence, practical clock-tree design guidance, and a transparent comparison of parameter gaps. It also distinguishes confirmed electrical facts from unverified details rather than inferring missing timing values or assuming drop-in alternatives where the supplied cross-reference data does not prove compatibility.

Devis Contact
ICS542MI - 156 MHz 1:2 Clock Buffer | Renesas Electronics
ICS542MI

ICS542MI - 156 MHz 1:2 Clock Buffer | Renesas Electronics

Renesas Electronics ICS542MI is a CMOS clock fanout buffer and divider IC that accepts a clock input up to 156 MHz and produces two clock outputs with divide ratios selected from 2, 4, 6, 8, 12, or 16. The device operates from 3 V to 5.5 V and is supplied in an 8-pin SOIC package measuring 3.90 mm in width. According to the Renesas Electronics 542 datasheet, one output is a low-skew divide-by-two version of the other output. A clock fanout buffer is a timing-device category used to distribute one periodic signal to multiple circuit loads. Clock buffers, sometimes called clock drivers, reproduce a clock with controlled loading, skew, and output characteristics. The ICS542MI combines clock distribution with programmable division, placing it in the hierarchy of clock and timing IC, clock buffer, clock divider, and timing-control semiconductor. The verified operating limit of 156 MHz supports high-speed digital logic, processor interfaces, communications equipment, and clock-tree distribution. Its 3 V to 5.5 V supply range allows use in both 3.3 V and 5 V systems, while CMOS inputs and three-state CMOS outputs support integration with digital clock domains. The exact divider-selection truth table and enable behavior should be verified against the manufacturer datasheet before implementation. Renesas describes the ICS542 as a cost-effective way to generate a high-quality divided clock output. One output provides the selected divided frequency, while the other is described as a low-skew divide-by-two output relative to that clock. This arrangement can reduce fanout loading and provide two related clocks to different downstream circuits without requiring multiple separate divider packages. Typical uses include fanout for digital logic, local clock distribution in communication systems, generation of related clocks for data converters or processors, and systems that need a divided clock alongside a further divided low-skew clock. The 8-SOIC package also makes the ICS542MI suitable for conventional surface-mount PCB layouts where a larger leaded package would be unnecessary. Designers should use short, impedance-controlled clock traces, provide a clean reference clock, and confirm output-state and division-selection requirements from the datasheet. Because the verified snippets do not provide detailed rise time, output impedance, skew, current, temperature, or pin-level thresholds, those values must not be inferred from the frequency and supply limits. This page distinguishes verified specifications from parameters that require confirmation from the manufacturer datasheet.

Devis Contact
ICS542MIT - 1:2 156 MHz Clock Fanout Buffer | Renesas
ICS542MIT

ICS542MIT - 1:2 156 MHz Clock Fanout Buffer | Renesas

Renesas Electronics ICS542MIT is a clock fanout buffer and divider integrated circuit with a 1:2 division ratio, a maximum operating frequency of 156 MHz, and an 8-SOIC package measuring 3.90 mm in width. It accepts a CMOS clock input and provides two three-state CMOS outputs, making it suitable for distributing a divided clock to multiple digital loads. A clock fanout buffer is a clock and timing IC that reproduces or distributes a clock signal while controlling impedance, loading, and signal timing. The ICS542MIT belongs to the broader clock buffer and driver hierarchy, where clock distribution devices isolate a source from downstream capacitance and provide predictable edge propagation into logic circuits. Its 3 V to 5.5 V supply range allows operation across common low-voltage digital systems. The device combines a 1:2 divider function with clock fanout capability. Its three-state CMOS outputs can place individual outputs into a high-impedance state when the receiving circuitry does not need a clock, while the 156 MHz maximum frequency supports common communications, control, and digital-logic clock domains. The 8-SOIC package is suitable for conventional surface-mount PCB assembly and offers a practical upgrade path for designs requiring more than a direct clock connection. Clock distribution requires careful attention to edge rate, output loading, return path continuity, and trace length. The three-state outputs make output-enable control relevant to system power management and bus segmentation. Because the ICS542MIT divides the input clock, downstream logic should be evaluated against the divided output frequency rather than assuming the source frequency appears unchanged at the receiver. Typical applications include communication equipment, control systems, test and measurement products, and general-purpose digital platforms that require one input clock to feed two destinations. The device is particularly useful where one subsystem needs a divided clock or where multiple clock domains must receive independently controlled outputs. Its 156 MHz ceiling also makes it applicable to systems operating below that frequency without requiring a higher-speed clock distribution architecture. When laying out the circuit, keep clock traces short, provide a continuous ground reference, and place decoupling close to the supply pins. Treat output-enable and input-clock timing as part of the system-level timing budget, especially when the buffer feeds a counter, latch, or communications transceiver. Confirm all timing, output-enable, and propagation-delay requirements against the manufacturer datasheet before release. This product page consolidates the confirmed ICS542MIT electrical and packaging details, practical clock-distribution guidance, a strict drop-in cross-reference, and design considerations that help engineers evaluate the device before schematic capture and PCB layout.

Devis Contact
ICS542MT - 1:2 Clock Buffer, 156 MHz, 8-SOIC | Renesas
ICS542MT

ICS542MT - 1:2 Clock Buffer, 156 MHz, 8-SOIC | Renesas

The Renesas ICS542MT is a clock fanout buffer and divider IC that accepts a CMOS clock input up to 156 MHz and provides a 1:2 divided clock output with three-state CMOS outputs. It operates from a 3 V to 5.5 V supply and is packaged in an 8-SOIC package measuring 0.154 inch wide and 3.90 mm in length. The ICS542MT is designed for clock distribution, frequency division, and systems where a stable divided clock is required from a higher-frequency source. A clock buffer or clock divider is a timing IC that conditions, distributes, or divides a digital clock signal. In the clock and timing hierarchy, the ICS542MT belongs to the clock buffer and divider family, which supports phase-locked-loop (PLL) based timing architectures, communications equipment, and digital processing systems. A divide-by-two function can reduce the output frequency while preserving a defined relationship to the input clock, while the three-state output structure allows the output to be disabled when it is not needed. The verified device information identifies a maximum frequency of 156 MHz, a 1:2 divide ratio, CMOS input and output signaling, and a 3 V to 5.5 V operating supply range. The manufacturer’s ICS542MT documentation describes the device as a cost-effective way to produce a quality clock output divided from a clock input. This combination makes it suitable for clock generation, timing distribution, and intermediate frequency conversion stages in communication and digital electronics. Because the ICS542MT uses proprietary PLL techniques to produce the divided clock, PCB layout and supply decoupling should be treated as part of the timing design rather than added afterward. Keep the clock input and output traces short, provide a clean ground reference, and place bypass capacitors close to the supply pins. When replacing the part, verify that the alternative has the same SOIC-8 footprint, pin assignments, input/output logic levels, and divide behavior; a similar frequency rating alone does not guarantee drop-in compatibility. Typical application areas include communications and networking clock trees, frequency conversion after an upstream oscillator or PLL, and digital subsystems requiring a locally divided clock. The page combines verified manufacturer and distributor information with practical selection guidance, application notes, and drop-in alternative analysis to help engineers evaluate ICS542MT designs faster.

Devis Contact
ICS548G-05 - Low-Jitter PLL Clock Synthesizer | Renesas
ICS548G-05

ICS548G-05 - Low-Jitter PLL Clock Synthesizer | Renesas

Renesas Electronics ICS548G-05 is a low-cost, low-jitter PLL clock synthesizer designed to generate x16 and x24 clocks from T1 and E1 reference frequencies, with a listed output frequency of 49.152 MHz and operation from 3.15 V to 5.5 V. The device is packaged in a surface-mount 16-pin TSSOP with a 4.40 mm body width. It is intended for communications timing, audio sampling-rate generation, and clock-distribution designs requiring multiple related outputs from one reference. A PLL clock synthesizer is a clock-and-timing integrated circuit that multiplies or divides a reference signal and then distributes the resulting clock through dedicated output drivers. Within the product hierarchy, the ICS548G-05 is a clock synthesizer and frequency multiplier, a member of the broader PLL and clock-management IC category, and ultimately part of the semiconductor timing-control ecosystem. Its low-jitter design makes it useful where the synthesized clock must support timing-sensitive digital or communications functions. Key features include a 16-pin TSSOP package, a 3.15 V to 5.5 V supply range, and synthesis of x16 and x24 clocks from T1 and E1 frequencies. The manufacturer describes the ICS548-05 as a low-cost, high-performance clock synthesizer using patented analog/digital PLL techniques. It accepts a crystal or clock input and generates popular communications frequencies, allowing multiple related clock outputs to replace separate oscillator arrangements. The listed 49.152 MHz output is directly associated with audio-clock and sampling-rate use cases. The PLL architecture separates frequency generation from the external reference source. A crystal or clock input establishes the reference, while the internal synthesizer produces the required derived clock frequencies. Output drivers then provide CLK and related divided or multiplied clock signals. Publicly indexed descriptions also identify CLK and CLK/2 outputs, tri-state capability, and low-skew clock distribution, making the device relevant to designs that need multiple synchronized signals rather than a simple single-ended oscillator. Typical uses include MP3 and digital-audio systems, communications equipment operating around T1 and E1 timing, and clock trees for digital signal processors, converters, and interface logic. The 16-TSSOP format supports compact surface-mount assemblies while exposing reference, power, control, and clock-output functions. In a typical circuit, the reference source and required decoupling capacitors are placed close to the device, while each clock trace is routed to minimize loading and preserve edge quality. Design attention should center on reference stability, correct mode selection, output loading, and power sequencing. Because PLL jitter and phase error depend on the reference source and loop operating conditions, the crystal or external clock must meet the timing requirements stated in the manufacturer datasheet. Keep clock traces short, avoid unnecessary stubs, and use controlled-impedance routing when the output drives longer PCB paths. Confirm all supply, ground, and output connections against the package pin-description table before layout release. This product page combines the manufacturer's device description with practical clock-tree guidance, drop-in option analysis, and application-oriented design context. It helps engineers distinguish the ICS548G-05 from ordinary fixed-frequency oscillators and generic dividers by focusing on its PLL-based synthesis, x16 and x24 multiplication functions, low-jitter communications-clock role, and compact 16-TSSOP implementation.

Devis Contact
ICS551M - 1:4 160MHz CMOS Clock Buffer | Renesas
ICS551M

ICS551M - 1:4 160MHz CMOS Clock Buffer | Renesas

The Renesas Electronics ICS551M is a 1:4 CMOS clock fanout buffer with a 160 MHz maximum operating frequency and a 3 V to 5.5 V supply range, housed in an 8-pin SOIC package. Designed as a low-cost, high-speed clock distribution device, it accepts one CMOS clock input and provides four buffered CMOS outputs, making it suitable for clock fanout in compact digital systems. A clock fanout buffer is a clock-and-timing integrated circuit that distributes one incoming clock signal to multiple downstream loads. Its place in the hierarchy is clock buffer → clock fanout buffer → clock distribution IC → timing and logic semiconductor. The ICS551M helps isolate clock loads from one another, reduces loading on the source clock, and provides separate outputs for multiple sequential or peripheral circuits. This is especially useful when a single oscillator or clock source must feed several logic blocks. Key verified characteristics include a 1:4 fanout ratio, 160 MHz maximum frequency, CMOS input and output technology, and an operating supply range of 3 V to 5.5 V. The 8-SOIC package measures 0.154 inches, or 3.90 mm, in width according to distributor data. These specifications make the device appropriate for general-purpose clock distribution where a compact surface-mount package and moderate operating frequency are sufficient. The ICS551M belongs to the ICS ClockBlocks family and is identified by distributor listings as a low-cost, small clock buffer. Because its outputs are CMOS, the downstream circuits must be compatible with the selected supply voltage and input thresholds. The device is not a PLL, oscillator, or level shifter; its function is specifically clock replication and distribution. Designers should preserve the input and output timing relationship, maintain the required supply decoupling, and account for trace and load differences among the four outputs. Typical applications include clock distribution in embedded control systems, digital logic networks, communications equipment, test and measurement systems, and general-purpose processor or peripheral clocking. For a design that needs more independent clock domains, frequency generation, or differential clock outputs, a different clock-and-timing device may be more appropriate. For applications requiring only one input and four CMOS copies, the ICS551M provides a straightforward distribution function in an established 8-SOIC footprint. The main design consideration is ensuring that every connected load, trace, and voltage domain is compatible with the available 160 MHz clock. Check rise and fall-time requirements, fanout loading, power-supply noise sensitivity, and the clock-source timing margin before production release. This page synthesizes verified distributor specifications, sourcing links, package information, and engineering guidance while leaving unverified values explicitly unresolved. The ICS551M datasheet and application information should be consulted for complete pin functions, electrical limits, timing characteristics, and recommended circuit implementation. Distributor data confirms the core identity and major specifications, but it does not provide enough evidence here to infer undocumented timing, current, or package dimensions.

Devis Contact
ICS551MI - 1:4 160MHz CMOS Clock Buffer | Renesas
ICS551MI

ICS551MI - 1:4 160MHz CMOS Clock Buffer | Renesas

The Renesas Electronics ICS551MI is a low-cost, high-speed 1-input to 4-output CMOS clock fanout buffer rated up to 160 MHz, supplied in an 8-SOIC package. Its principal specifications are a 3 V to 5.5 V supply range, CMOS input and output interfaces, four buffered outputs, and a maximum operating frequency of 160 MHz. The device belongs to the clock and timing IC category and is designed for distributing one clock signal across several digital loads without requiring the source device to drive all loads directly. A clock fanout buffer is a digital timing component that reproduces an input clock at multiple outputs. It sits between a clock source and the circuits requiring that reference, reducing fanout loading and helping isolate each destination from the others. The ICS551MI is specifically described as a low-cost, small clock buffer and is part of the ICS ClockBlocks product family. Its 1:4 topology gives a designer four available clock destinations from one source. The verified feature set emphasizes simplicity rather than advanced configuration. The ICS551MI accepts CMOS logic, produces CMOS outputs, operates from 3 V to 5.5 V, and supports frequencies through 160 MHz. It is not presented as a programmable, differential, low-power, or phase-aligned clock-device family member. That makes it suitable where a conventional single-ended clock must be distributed to multiple conventional CMOS loads. The 8-SOIC package provides a compact surface-mount footprint and exposes the input, outputs, supply, and ground connections needed for a conventional fanout implementation. Its operating characteristics allow operation in both 3.3 V and 5 V system contexts within the stated 3 V to 5.5 V supply range. Designers should still confirm timing, output loading, and temperature requirements against the complete manufacturer datasheet before production release because those detailed values are not present in the retrieved source excerpts. Typical uses include distributing a processor or controller clock to communications logic, digital peripherals, counters, or data-conversion subsystems. In a four-output arrangement, the buffer can feed multiple loads while reducing the electrical burden on the original clock source. Because the outputs are not specified as independently selectable or phase-aligned in the retrieved data, the design should treat them as a conventional fanout network rather than a deterministic multi-clock generator. The primary design consideration is to place the clock buffer close enough to the receiving circuits to limit trace loss and maintain signal integrity. PCB routing should preserve a consistent ground reference, avoid long unterminated stubs, and account for the capacitive loading introduced by each connected output. Supply decoupling and output loading should be verified against the full datasheet and the worst-case clock topology used in the final board. This page consolidates the verified distributor specifications, package information, sourcing links, practical clock-distribution guidance, and honestly identifies missing electrical details. It is intended to help engineers locate the ICS551MI datasheet, compare it with related clock devices, and determine whether its basic 1:4 CMOS fanout function fits the target design.

Devis Contact
ICS551MIT - 1:4 Clock Fanout Buffer, 160 MHz | Renesas
ICS551MIT

ICS551MIT - 1:4 Clock Fanout Buffer, 160 MHz | Renesas

The Renesas Electronics ICS551MIT is a low-cost, high-speed clock fanout buffer with a 1:4 fanout ratio, maximum operating frequency of 160 MHz, CMOS inputs and CMOS outputs, and a 3 V to 5.5 V supply range. It is packaged in an 8-SOIC package measuring 0.154 inch, or 3.90 mm, in body width. A clock fanout buffer is a clock-and-timing integrated circuit that distributes one input clock to multiple output branches. It belongs to the hierarchy of clock buffer, clock distribution device, clock and timing IC, and semiconductor. By recreating the input signal at four outputs, the ICS551MIT can reduce the loading on a clock source while supporting multiple downstream clock domains. The principal features of the ICS551MIT are its 1:4 fanout configuration, 160 MHz maximum frequency, CMOS input and output interfaces, and single-supply operation from 3 V to 5.5 V. The part is identified as a low-cost member of the IDT ClockBlocks family and is positioned for compact, cost-sensitive designs that require more than one clock output without the footprint of a larger multi-output device. Its architecture separates the single clock input from four buffered CMOS outputs. This arrangement allows one upstream oscillator or controller to feed several clock-enabled circuits while preserving a consistent clock source throughout the subsystem. The manufacturer documentation identifies the device as a small, high-speed clock buffer, although detailed propagation-delay, skew, rise-time, and fall-time limits must be checked in the datasheet before relying on a particular timing budget. Typical uses include network-interface clock distribution, communications equipment, test and measurement systems, and general digital subsystems requiring a one-input, four-output clock arrangement. The 8-SOIC footprint can also simplify transitions from larger clock-buffer packages when a design requires four outputs but does not need a dual-channel monolithic implementation. PCB implementation should preserve short clock traces, provide a continuous ground reference, and route outputs away from high-current switching paths. Because clock edges can pick up coupling and skew, the input and output nets should use consistent topology, and unused outputs should be handled according to the manufacturer's pin-description and output-disable guidance rather than left floating. This product page combines the manufacturer specifications, verified distributor listings, package details, drop-in candidates, comparison data, and practical layout guidance. It is intended to help engineers assess the ICS551MIT for clock distribution and identify the next step for sourcing or PCB-level replacement.

Devis Contact