Produits (39 000+)

LT1885IS - Quad Precision Op Amp | Analog Devices
LT1885IS

LT1885IS - Quad Precision Op Amp | Analog Devices

Analog Devices LT1885IS is a four-circuit, precision operational amplifier with rail-to-rail output and picoamp-class input performance, offered in a 14-pin small-outline integrated-circuit package. The device combines input offset voltage trimmed below 50 µV with rail-to-rail output operation, making it suitable for instrumentation, sensor conditioning, and low-level signal-chain applications where accurate output swing and low input bias current are important. An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify, buffer, filter, or control voltages. The LT1885 belongs to the precision operational-amplifier hierarchy, where input offset, input bias current, output swing, noise, and stability determine suitability for measurement systems. Its four amplifiers share one package while providing independent signal paths, reducing component count in multi-channel designs. The LT1885 family is designed for precision applications that benefit from rail-to-rail output operation. Rail-to-rail output allows the amplifier output to approach the available supply rails more closely than a conventional output stage, which can improve dynamic range in low-voltage systems. Picoamp-class input performance is particularly useful when measuring high-impedance sources because the amplifier contributes less input bias current to the measured node. According to the Analog Devices product information, the LT1884 and LT1885 op amps provide high-accuracy input performance while maintaining rail-to-rail output swing and faster response than other precision amplifiers. Input offset voltage is trimmed to less than 50 µV, supporting accurate conditioning of small differential signals. The LT1885IS contains four amplifiers, while the related LT1884 family is associated with dual-channel configurations. Typical uses include precision sensor interfaces, low-current measurement stages, current-to-voltage conversion, signal buffering, and multi-axis measurement systems. The four-channel organization is especially useful when four sensors require similar conditioning electronics or when symmetric analog channels are needed in an industrial, medical-instrumentation, or test-and-measurement system. Designers should verify supply voltage, input common-mode range, output swing under load, noise, gain-bandwidth product, and stability requirements against the manufacturer datasheet for the selected ordering code. Decoupling capacitors should be placed close to the supply pins, and sensitive high-impedance nodes should be protected from leakage, contamination, and electrostatic discharge. This product page organizes the LT1885IS family information with practical design considerations, qualified same-family alternatives, package details, and application guidance to support component selection and PCB planning.

Devis Contact
LT1970AIFE#TRPBF - ±500mA Power Op Amp | Analog Devices
LT1970AIFE#TRPBF

LT1970AIFE#TRPBF - ±500mA Power Op Amp | Analog Devices

The Analog Devices LT1970AIFE#TRPBF is a ±500mA power operational amplifier with precise externally controlled current limiting, offered in a 20-pin TSSOP-EP package (5V to 36V supply range). It delivers independent 1%-accurate sourcing and sinking current limit thresholds via separate control voltages, and supports output current boosting through external power transistors. A power operational amplifier (power op amp) is a specialized high-current linear amplifier that combines the precision of a small-signal op amp with the drive capability of an output stage typically rated from hundreds of milliamps to several amps. Within the broader hierarchy, power op amps sit under operational amplifiers -> amplifiers -> analog ICs -> signal conditioning -> semiconductors. They are commonly used as programmable voltage or current sources, motor drivers, and audio amplifiers where a standard op amp cannot deliver sufficient load current. Key features include ±500mA minimum output current, 1.6 V/µs slew rate, independent adjustment of source and sink current limits, single or split supply operation from 5V to 36V total, and thermal shutdown. The exposed pad (TSSOP-EP) package provides a low thermal resistance path, which is critical for sustaining 500mA continuous output. The current-limit architecture uses two external programming voltages, enabling asymmetric sourcing and sinking limits for applications such as Class-AB audio or solenoid drive. Internally the LT1970A uses a bipolar output stage with a precision current-sense scheme that compares each external limit voltage against an internal VBE-referenced sense threshold. The 1% limit accuracy (improved from the LT1970's 2%) reduces output stage stress and enables tighter compliance envelopes in regulated current sources. Single-supply operation is supported by an internal charge pump, allowing the output to swing within a few hundred millivolts of each rail. Typical applications include programmable current sources, solenoid and valve drivers, audio amplifiers (Class A, B, AB), motor drivers, and transducer excitation. The TSSOP-EP footprint is well suited for compact industrial and instrumentation designs that require high current density on a small PCB. When designing with this part, dedicate a generous copper pour under the exposed pad to keep junction temperature within the 150°C absolute maximum. Decouple both supply rails close to the IC with 1µF X7R ceramics in parallel with 10µF bulk; the high output current makes supply-impedance-induced ringing a real concern. This page consolidates distributor pricing, drop-in same-package alternatives, application circuits, and PCB-level design notes that are not aggregated in the manufacturer datasheet alone.

Devis Contact
LT1970IFE - ±500mA Power Op Amp | Analog Devices
LT1970IFE

LT1970IFE - ±500mA Power Op Amp | Analog Devices

The Analog Devices (formerly Linear Technology) LT1970IFE is a ±500 mA power operational amplifier with precise externally controlled current limiting, housed in a 20-pin TSSOP-EP (FE) package with an exposed thermal pad. It supports single or split supply operation from 5 V to 36 V total supply voltage and provides separate control voltages for sourcing and sinking current-limit sense thresholds with 2 % accuracy, enabling programmable bidirectional current limiting without external sense resistors. A power op amp is a specialized operational amplifier designed to deliver output power levels orders of magnitude greater than a conventional op amp. Unlike a small-signal op amp that typically sources or sinks tens of milliamps, a power op amp integrates output stages capable of hundreds of milliamps to several amps, often with thermal protection, current limiting, and short-circuit handling. Power op amps sit hierarchically between op amps and power management ICs, frequently replacing discrete driver + MOSFET combinations in programmable current sources, motor drivers, and audio line drivers. The LT1970 specifically combines power-output stages with adjustable precision current limiting, making it a single-chip alternative to discrete driver designs. Key features include ±500 mA minimum output current, 2 % accurate independent source and sink current-limit programming via external control voltages, the ability to boost output current by adding external power transistors, single or split supply operation from 5 V to 36 V, and thermal shutdown with the exposed pad for low thermal resistance. The output stage swings to within ±2.5 V of either supply rail at full current. The architecture uses a precision input stage followed by a high-current output stage with separate current-sense paths. The sourcing and sinking current limits are independently programmed by two DC control voltages on the ILIM+ and ILIM- pins, allowing asymmetric profiles for charging supercapacitors or driving inductive loads. External boost transistors can multiply output current beyond 500 mA while preserving the precision current-limit function. Typical applications include programmable current sources for LED drivers, solenoid and actuator drivers, motor torque drivers, headphone amplifiers, programmable power supplies, and battery chargers. The wide supply range makes the LT1970 particularly suited to industrial 24 V bus systems and automotive 12 V/24 V loads. When designing with this device, place a 1 µF bypass capacitor close to each supply pin and use the exposed pad for thermal dissipation. For applications above 500 mA, ensure the external boost transistors are mounted on a thermally adequate footprint and that the current-limit control voltages remain stable across the operating temperature range. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the LT1970IFE that complement the official datasheet by adding cross-source comparisons and PCB-level guidance.

Devis Contact
LT311AN8 - 30V, 200ns Voltage Comparator | Analog Devices
LT311AN8

LT311AN8 - 30V, 200ns Voltage Comparator | Analog Devices

The Analog Devices LT311AN8 is a general-purpose, single voltage comparator with a 5V to 30V single-supply range, differential input capability, and a fast 200 ns response time, housed in an 8-pin PDIP package. Verified distributor data identifies a maximum input offset voltage of 2 mV, while another supplier lists 1 mV at ±15 V; engineers should therefore verify the exact test conditions in the manufacturer datasheet before setting precision thresholds. A voltage comparator is an analog interface IC that compares two input voltages and produces a logic-level result indicating which input is higher. It belongs to the comparator hierarchy within interface and signal-conditioning semiconductors. Unlike a general-purpose operational amplifier used primarily for linear amplification, a comparator is optimized for fast saturation and switching, making it useful for threshold detection, sensor conditioning, pulse shaping, and control systems. The LT311AN8 combines a single comparator with an 8-pin through-hole package. The verified supply specifications include 5V to 30V operation and ±2.5 V to ±15 V dual-supply operation. A 200 ns response time supports applications requiring rapid transitions, while the stated bipolar input arrangement supports operation around ground and with bipolar supplies. Exact input common-mode limits, output-swing limits, hysteresis behavior, and latch configuration were not provided in the verified data and require datasheet confirmation. Typical circuit roles include monitoring a sensor output against a reference, detecting an overvoltage condition, converting a slowly changing analog level into a digital event, and generating a pulse when a threshold is crossed. Because a comparator output can change rapidly near its switching threshold, input noise, propagation delay, output-capacitance, and layout parasitics can affect system behavior. A stable reference and short feedback or hysteresis path may be needed when the input signal has appreciable noise or slow slew rate. The principal design consideration is to verify supply polarity, input range, output compatibility, and logic thresholds against the actual operating rail. Do not assume that the 30 V maximum supply rating permits inputs or outputs outside the device's specified common-mode and absolute-maximum limits. Confirm that downstream devices accept the electrical output levels and that the comparator's response time is adequate for the required timing margin. This page consolidates the verified distributor identity, package, supply, offset, response-time, and commercial-search data for LT311AN8. It also distinguishes verified facts from missing technical fields and avoids presenting unverified drop-in substitutes as guaranteed replacements, helping engineers evaluate the part with appropriate sourcing and validation caution.

Devis Contact
LT318AH - 15MHz High-Speed Operational Amplifier | Analog Devices
LT318AH

LT318AH - 15MHz High-Speed Operational Amplifier | Analog Devices

The Analog Devices LT318AH is a standard general-purpose high-speed operational amplifier with one circuit, a nominal unity-gain bandwidth of 15 MHz, and an 8-lead round TO-5 through-hole package. The verified distributor information identifies the device as a high-speed operational amplifier, while the available product data also lists a 70 V/µs slew rate and approximately 5 mA supply current. Its military-grade designation and hermetic-style package make it relevant to precision analog, signal-conditioning, instrumentation, and test systems where bandwidth and transient response matter. An operational amplifier is an analog integrated circuit that uses high-gain feedback to amplify the difference between two input voltages. In the broader electronics hierarchy, the LT318AH is an operational amplifier, analog IC, and semiconductor. Its high bandwidth permits wider signal bandwidth than slower general-purpose amplifiers, while its slew rate determines how quickly the output can move through voltage changes. These characteristics make it useful in active filters, buffers, low-level signal chains, feedback control, and measurement circuits. The verified data identifies the LT318AH as a single-circuit amplifier with a 15 MHz nominal unity-gain bandwidth and 70 V/µs slew rate. The available distributor listing also reports approximately 0.5 µA maximum average input bias current in one marketplace result, while another product listing reports a 5 mA supply current. These figures should be checked against the manufacturer datasheet for the exact test conditions, supply voltage, temperature grade, and load conditions before final design sign-off. The device is packaged as an 8-terminal round TO-5/MDTALCAN through-hole package. Its leaded construction is mechanically distinct from modern surface-mount op amps, so PCB replacement must account for the original footprint, lead spacing, thermal requirements, and pin orientation. The verified sources disagree on some commercial and historical details, including temperature-grade descriptions and lifecycle status, so those fields remain qualification-dependent rather than inferred. Typical uses include high-speed instrumentation, precision signal buffering, active analog filtering, test-equipment input stages, and feedback loops requiring faster transient response than a conventional low-frequency precision amplifier. For new designs, verify the exact LT318AH datasheet, military qualification requirements, supply limits, input/output ranges, noise, bias current, stability configuration, and availability before committing the layout. The key design consideration is to verify the complete pinout and electrical limits in the manufacturer datasheet before layout or replacement. Decouple the supply pins locally, keep feedback traces short, and verify stability with the intended source and load. Because this is a through-hole TO-5 device, production cost, availability, and thermal performance may differ substantially from newer surface-mount alternatives. This page consolidates verified manufacturer and distributor information with explicit data gaps, practical application guidance, and drop-in replacement screening. It does not invent missing electrical values, lifecycle claims, qualification details, or cross-reference parts that were not established by the supplied evidence.

Devis Contact
LT318AJ8 - High-Speed Operational Amplifier | Analog Devices
LT318AJ8

LT318AJ8 - High-Speed Operational Amplifier | Analog Devices

The Analog Devices LT318AJ8 is a single-circuit, high-speed operational amplifier in an 8-pin CERDIP package. The verified product data identifies it as a standard general-purpose instrumentation amplifier building block with eight through-hole terminals and a commercial temperature grade. Its high-speed architecture is intended for precision signal paths where response speed and signal integrity matter more than micropower operation. An operational amplifier is an active analog device that uses high open-loop gain to amplify the difference between its inverting and non-inverting inputs. In the broader electronics hierarchy, it belongs to the operational-amplifier family, then to analog signal-conditioning ICs and semiconductors. Negative feedback commonly shapes closed-loop gain, while the amplifier supplies the output current needed to drive the external load. The LT318A family is specifically described by Analog Devices as a high-speed operational amplifier. That classification makes it relevant to instrumentation, measurement, buffering, and precision feedback systems. The available verified sources do not publish numerical gain-bandwidth, slew-rate, input-offset, supply-voltage, noise, or current figures, so those values must be taken directly from the manufacturer data sheet before sizing compensation, checking stability, or calculating noise performance. The J8 ordering code corresponds to the 8-pin CERDIP package shown by DigiKey and other distributors. A through-hole ceramic dual-inline package supports conventional PCB insertion and is distinct from surface-mount SOIC variants. The suffix should not be treated as an electrical grade or performance option by itself; confirm the complete family data and ordering information in the Analog Devices LT318A documentation. Typical uses include precision instrumentation signal conditioning, low-level analog amplification, active filtering, data-acquisition front ends, and feedback networks in measurement systems. These applications benefit from the device's stated high-speed characterization, but stability and bandwidth must be confirmed against the actual closed-loop circuit, source impedance, load, supply rails, and compensation network. The principal design consideration is that package compatibility alone does not guarantee replacement compatibility. Verify offset voltage, input bias current, slew rate, gain-bandwidth product, output swing, supply range, noise, and stability for any substitute. Decoupling, grounding, feedback-loop layout, and output-load conditions can affect performance as much as the nominal amplifier specifications. This page combines verified manufacturer and distributor information with package, sourcing, comparison, and design guidance. It distinguishes documented facts from missing numerical parameters and does not infer an electrical match where the supplied sources do not provide one.

Devis Contact
LT318AN8#PBF - 15MHz 70V/us Op Amp | Analog Devices
LT318AN8#PBF

LT318AN8#PBF - 15MHz 70V/us Op Amp | Analog Devices

The Analog Devices LT318AN8#PBF is a single, general-purpose, high-speed operational amplifier with 15 MHz gain-bandwidth product, 70 V/us slew rate, and one circuit in an 8-pin PDIP package. The through-hole DIP format supports conventional PCB insertion and prototyping, while the leaded package is suited to instrumentation, signal-conditioning, and test systems. According to the manufacturer product page, the LT318A family is in production and begins at $3.46 per unit. A high-speed operational amplifier is a voltage-feedback amplifier designed to amplify small signal variations while maintaining useful bandwidth and slew performance. In the electronics hierarchy, an operational amplifier belongs to the amplifier-IC family and the broader semiconductor category. The LT318A's combination of bandwidth, slew rate, and general-purpose classification makes it relevant where signal response must be faster than that of conventional precision or low-noise amplifiers. The verified data identifies the LT318A as a 15 MHz high-speed amplifier with a 70 V/us slew rate. These two specifications describe different dynamic limits: gain-bandwidth product controls small-signal response, while slew rate controls how rapidly the output can move under large-signal conditions. The 8-DIP package measures 0.300 inches, or 7.62 mm, according to the distributor specification listing, and the product is supplied in a tube. The LT318AN8#PBF is categorized by DigiKey as a standard, general-purpose amplifier with one circuit. Its 8-terminal PDIP construction and through-hole form factor distinguish it from surface-mount operational amplifiers, making it useful where component insertion, socket use, or manual replacement is preferred. Because high-speed amplifiers can oscillate or produce unstable outputs when layout and compensation conditions are poor, feedback routing, grounding, bypassing, and load capacitance require careful attention. Typical uses include low-frequency instrumentation signal paths, laboratory test equipment, communications-related signal conditioning, analog control blocks, and educational or prototyping circuits. The verified data does not provide input-offset voltage, input-bias current, noise density, common-mode range, supply range, output swing, or stability-versus-capacitance values, so those specifications should be confirmed in the LT318A manufacturer datasheet before final design release. The principal design consideration is to preserve high-speed behavior without introducing excessive instability. Keep feedback components close to the amplifier, use a compact ground-return path, bypass supply pins at the circuit, and avoid long unprotected traces. If the load is capacitive or the feedback network is electrically long, compare the simulated result against the manufacturer's recommended compensation and stability guidance. This page combines the verified manufacturer and distributor metadata with a practical explanation of package, speed, sourcing, and design-selection questions. It also distinguishes confirmed LT318A attributes from parameters that still require datasheet verification, avoiding unsupported claims while helping engineers plan instrumentation and high-speed analog prototypes.

Devis Contact
LT319AH - Dual Open-Collector Comparator | Analog Devices
LT319AH

LT319AH - Dual Open-Collector Comparator | Analog Devices

The Analog Devices LT319AH is a production dual comparator with two independent high-gain comparison channels, open-collector outputs, bipolar construction, and a 10-pin round TO-5 through-hole package. The verified distributor data identifies a commercial-grade part with an operating temperature range of 0°C to 70°C, bipolar technology, and dual supplies spanning ±2.5 V minimum to ±15 V maximum. Its 80 ns response figure and open-collector output make it useful for line-driver, threshold, and interface circuits. A comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating whether the non-inverting input is above or below the inverting input. The LT319AH belongs to the dual-comparator hierarchy, combining two similar channels in one package. Its open-collector outputs require an external pull-up resistor when the output must rise to a defined logic high. Verified product information describes the LT319AH as an improved relative to the LM119 family, with lower input offset voltage and offset current, higher voltage gain, guaranteed common-mode rejection, and input protection diodes. The identified response time is 80 ns, while one distributor result reports 150 nA input bias current. These features support applications that require fast decisions, predictable offset behavior, and protection at the inputs. The LT319AH is produced under the Analog Devices product family and has a listed starting price of $3.23 on the official product page. Commercial-grade operation from 0°C to 70°C supports cost-sensitive industrial and instrumentation designs when that temperature range is acceptable. Its through-hole TO-5 package is mechanically straightforward for legacy PCBs, test fixtures, and hand-assembled prototypes. Typical circuit roles include dual-threshold detection, pulse-width or timing comparison, low-level digital interfacing, and two-channel sensing. Because the outputs are open collector, designers should verify pull-up voltage, pull-up resistance, sink-current capability, input common-mode limits, and supply polarity before implementation. The separate ground arrangement should also follow the manufacturer’s connection guidance. For new layouts, a surface-mount alternative may be mechanically easier to automate, but changing packages requires a PCB redesign. For repair and legacy production, keeping the original TO-5 footprint and verifying the 10-pin connection order is more important than selecting a merely similar dual comparator. This page consolidates verified manufacturer information, distributor availability references, pricing context, package details, and practical procurement guidance for engineers evaluating the LT319AH. It does not infer a drop-in replacement where the provided evidence does not establish one.

Devis Contact
LT319AN - Dual 80ns Comparator, 14-PDIP | Analog Devices
LT319AN

LT319AN - Dual 80ns Comparator, 14-PDIP | Analog Devices

The Analog Devices LT319AN is a dual, general-purpose comparator with a guaranteed maximum 0.5 mV input offset voltage, 80 ns response time, 25 mA output drive capability, and operation from a single 5 V supply. It is packaged in a 14-pin PDIP. The LT319AN is the leaded, non-automotive-temperature designation associated with the LT319A dual-comparator family. A comparator is an integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. As a dual comparator, the LT319AN contains two independent comparison channels in one package. This dual-channel structure places the device in the comparator hierarchy: comparator > analog comparator > linear integrated circuit > semiconductor. It is useful when a system needs fast threshold detection, signal conditioning, or differential logic conversion. The LT319A family is described by Analog Devices as an improved version of the LM119 dual comparator. Its key advantages include lower input offset voltage and offset current, higher voltage gain, guaranteed common-mode rejection, and input protection diodes. The maximum 0.5 mV offset specification reduces ambiguity near the switching threshold, while the 80 ns response time supports high-speed decision-making. The 25 mA output drive capability allows the outputs to interface with suitable TTL-compatible circuitry. Operation from a single 5 V supply simplifies the power architecture in TTL and mixed-signal systems. The 14-pin PDIP package also supports conventional through-hole assembly and prototyping. Because output behavior and input common-mode limits depend on the supply configuration, designers should consult the manufacturer datasheet before using the device outside its stated operating conditions. The separate ground arrangement discussed for the LT319A family can also assist system-ground isolation where applicable. Typical uses include high-speed threshold detection, pulse-width and timing measurements, zero-cross detection, signal conditioning, and two-channel sensing. One comparator channel can compare a sensor signal with a reference while the other performs an independent threshold or differential decision. The fast 80 ns response helps minimize propagation delay in timing-sensitive systems, and the 0.5 mV maximum input offset improves threshold repeatability. Layout should keep input and output paths short, provide a stable return path, and avoid routing sensitive input traces beside high-current switching nodes. Input protection diodes require attention when signals can exceed the supply rails. Designers should also account for output rise and fall time, supply bypassing, and input common-mode range when interpreting the 80 ns response specification. This page combines the verified manufacturer and distributor information with practical application guidance, sourcing details, comparison data, and design notes. It distinguishes explicitly verified LT319AN characteristics from parameters that still require confirmation from the official LT319A datasheet.

Devis Contact
LT319AN#PBF - 80ns Dual Comparator, 14-PDIP | Analog Devices
LT319AN#PBF

LT319AN#PBF - 80ns Dual Comparator, 14-PDIP | Analog Devices

The Analog Devices LT319AN#PBF is a dual general-purpose comparator with an 80 ns response time, open-collector outputs, and a 14-pin PDIP package. It operates from a single 5 V supply or from supply voltages spanning ±15 V. The device contains two independent comparison channels and is specified with a maximum input offset voltage of 0.5 mV, 25 mA output drive capability, and input protection diodes. A comparator is a high-gain analog signal-conditioning IC that evaluates two input voltages and produces a digital logic result indicating which input is higher. The LT319A belongs to the comparator hierarchy, which supports general-purpose analog and mixed-signal systems: comparator -> analog signal IC -> integrated circuit -> semiconductor. Its open-collector output requires an external pull-up resistor and can interface with systems using open-collector, open-emitter, or TTL-compatible signaling. Key features include two comparators per package, an 80 ns response time, a guaranteed maximum 0.5 mV input offset voltage, and 25 mA output drive capability. The single 5 V operating capability is useful for low-voltage logic systems, while the ±15 V supply capability supports higher-voltage analog and industrial control circuits. Input protection diodes help limit input stress, although external protection and supply-decoupling checks remain necessary in the final design. The LT319A architecture is intended for threshold detection, level translation, pulse generation, and high-speed switching decisions. Because the outputs are open collector, the output high level depends on the pull-up network and system voltage rather than an internal active pull-up. This makes the device adaptable to different logic families, but it also requires correct resistor selection and confirmation that the driven node meets the timing and current requirements of the receiving circuit. Typical applications include industrial control and automation, sensor threshold detection, pulse-width and timing circuits, level conversion, waveform conditioning, and embedded control systems. The 14-pin PDIP package is mechanically straightforward for through-hole assembly, prototyping, and repair. Its dual-channel configuration also reduces package count when two independent decisions are required in one circuit. When designing around the LT319AN#PBF, verify supply polarity, common-mode input limits, output pull-up values, and the maximum transition rate required by the downstream logic. Place bypass capacitors close to the supply pins and keep comparator input traces short to reduce noise pickup. The open-collector outputs can pull a logic node low but cannot source current, so a suitable pull-up resistor is mandatory. This page combines verified manufacturer and distributor data with practical comparator design guidance, application fit, package information, and drop-in replacement considerations for engineers evaluating the LT319AN#PBF.

Devis Contact
LT3669EUFD#PBF - IO-Link Transceiver with Buck/LDO | Analog Devices
LT3669EUFD#PBF

LT3669EUFD#PBF - IO-Link Transceiver with Buck/LDO | Analog Devices

The Analog Devices LT3669EUFD#PBF is an industrial IO-Link transceiver with an integrated step-down switching regulator and low-dropout linear regulator in a 28-QFN package. It combines wake-up detect functionality, a programmable power-on reset timer, and externally adjustable transmitter current limit and slew rate. The device is identified as a single transmitter/receiver IO-Link interface solution for industrial sensor and actuator systems. An IO-Link transceiver is a specialized interface IC that connects sensors, actuators, and industrial equipment using power and communication lines. The LT3669 integrates that interface function with local power conversion, allowing a system designer to provide both the IO-Link communication path and regulated auxiliary power from one device. Its architecture belongs to the transceiver, interface IC, power-management IC, and embedded industrial-control hierarchy. The principal verified features include a 28-pin QFN surface-mount package, integrated step-down regulator and LDO, wake-up detect, programmable power-on reset timing, and adjustable transmitter current limit and slew rate. The manufacturer describes the LT3669 family as recommended for new designs. These features make it useful in industrial IO-Link master or sensor interfaces where space, local power, fault handling, and deterministic startup behavior matter. The device can be used in industrial automation equipment, factory sensor nodes, actuator interfaces, process-control systems, and IO-Link-compatible sensor modules. The integrated power regulators reduce the number of separate support components, while wake-up detection can help a connected system recognize a remote device state. The programmable power-on reset timer provides additional control during system startup and recovery. When designing around the LT3669EUFD#PBF, engineers should verify the exact electrical limits, pin functions, regulator settings, and external component values against the official LT3669/LT3669-2 datasheet. The QFN package also requires careful PCB layout and thermal management. The integrated switching regulator can introduce layout-dependent EMI and high-current paths, so input decoupling, switching-loop minimization, and exposed-pad thermal design should be reviewed before production. This product page combines the verified Analog Devices product information, distributor listings, and practical engineering guidance. It is intended to help engineers identify the correct IO-Link transceiver, compare package and lifecycle information, locate the datasheet, and plan a robust industrial interface implementation. The target MPN includes the E suffix and PBF lead-free ordering designation; variant and package details should be confirmed against the manufacturer documentation before substituting or upgrading. LT3669EUFD#PBF is best suited to compact industrial IO-Link systems where communication, auxiliary power, wake-up detection, and programmable startup behavior are integrated in a single 28-QFN device. Use the manufacturer datasheet as the authority for final electrical, thermal, timing, and application values.

Devis Contact
LT3669EUFD#TRPBF - IO-Link Transceiver | Analog Devices
LT3669EUFD#TRPBF

LT3669EUFD#TRPBF - IO-Link Transceiver | Analog Devices

The Analog Devices LT3669EUFD#TRPBF is an industrial IO-Link transceiver with an integrated step-down switching regulator and low-dropout regulator, housed in a 28-QFN surface-mount package. The verified product listing identifies a 4 mm by 5 mm package and tape-and-reel ordering code TRPBF. Its integrated power architecture supports IO-Link sensor or actuator interfaces while reducing the number of external power-conversion stages required around the field device. An IO-Link transceiver is an industrial interface IC that connects a controller to sensors or actuators using IO-Link communication. In the broader hierarchy, it belongs to interface ICs and industrial fieldbus connectivity. The LT3669 family combines physical-layer signaling, wake-up detection, programmable power-on reset timing, and local power regulation so a compact sensor or actuator can be powered and communicated with in one assembly. According to the Analog Devices product page, LT3669 and LT3669-2 are recommended for new designs. The manufacturer datasheet also identifies wake-up detect and a programmable power-on reset timer. The transceiver's transmitter current limit and slew rate are externally adjustable, allowing the interface behavior to be matched to the connected industrial load and cable environment. The verified data does not provide numerical values for those adjustments. The integrated step-down regulator supplies a lower-voltage rail efficiently, while the LDO supports a cleaner local supply. Combining both functions with the IO-Link transceiver can simplify PCB area in industrial sensors, proximity devices, and actuator modules. The trade-off is a more specialized IC whose external component values, current limits, timing, and thermal performance must be selected together rather than as separate power-stage designs. The LT3669 family is suitable for factory automation, industrial sensing, actuator control, and fieldbus-connected modules where IO-Link power and communication share one interface device. The 28-QFN package requires careful PCB layout and adequate thermal design, particularly when the internal switching regulator operates at higher load. The manufacturer product page lists LT3669 and LT3669-2 as recommended for new designs, while the exact LT3669EUFD#TRPBF lifecycle status should be confirmed against current authorized-channel inventory. This page combines verified distributor listings, manufacturer positioning, package information, and practical design guidance for engineers evaluating the LT3669EUFD#TRPBF. Numeric electrical limits, pricing tiers, and detailed pin functions not present in the supplied source data are intentionally marked as data needed rather than inferred.

Devis Contact
LT3669EUFD-2#PBF - IO-Link Transceiver with Integrated Buck Regulator and LDO | Analog Devices
LT3669EUFD-2#PBF

LT3669EUFD-2#PBF - IO-Link Transceiver with Integrated Buck Regulator and LDO | Analog Devices

The Analog Devices LT3669EUFD-2#PBF is an IO-Link transceiver with an integrated step-down switching regulator and low-dropout linear regulator, designed for industrial interface applications and housed in a 28-pin QFN package. The LT3669-2 version supports an external catch diode and up to 300 mA switching-regulator load current according to the Analog Devices product page. The device combines one IO-Link transmitter and one receiver with wake-up detection and a programmable power-on reset timer, reducing the need for separate interface and power-management circuitry. An IO-Link transceiver is a specialized industrial interface IC that connects compatible sensors and actuators to a point-to-point communication link. The LT3669 combines this interface function with power conversion, placing the component in the broader hierarchy of industrial interface IC, transceiver, power-management IC, and semiconductor. Its integrated regulator can supply the connected IO-Link device while the transceiver handles wake-up, communication, and fault-related interface behavior. Key features identified in the verified Analog Devices material include one transmitter and one receiver, a 7.5 V to 40 V supply range, and a -40°C to +125°C operating-temperature range for the LT3669 comparison result. The LT3669-2 uses an external catch diode rather than the integrated catch diode used in the LT3669, making the external-diode distinction important when comparing versions. The manufacturer describes the LT3669 family as recommended for new designs. The switching-regulator and LDO architecture can simplify industrial sensor or actuator boards by reducing external power-conversion component count. The programmable power-on reset timer supports controlled startup sequencing, while wake-up detection helps the system respond to connected-device activity. Current limit and transmitter slew rate are externally adjustable according to the manufacturer datasheet, allowing board-level optimization for the intended interface load and cable environment. Typical applications include IO-Link sensors, proximity and position sensors, industrial actuators, factory automation equipment, and distributed industrial control systems. The wide 7.5 V to 40 V supply range is relevant for 24 V industrial environments, while the integrated regulator architecture is useful where board space and component count matter. The exact external diode, capacitor, resistor, and layout requirements must follow the Analog Devices datasheet. When designing a board around the LT3669EUFD-2#PBF, confirm the external catch-diode selection, regulator compensation, output capacitance, and exposed-pad thermal implementation against the manufacturer guidance. Keep sensitive communication and power-return paths short, and provide adequate copper area for the 28-QFN package. Verify the selected sensor or actuator’s IO-Link current, wake-up behavior, and electrical timing before finalizing the power budget. This page consolidates the verified manufacturer and distributor information, distinguishes the LT3669 and LT3669-2 external-diode distinction, and provides design-oriented guidance. Current pricing and availability remain distributor-dependent and should be checked for the exact suffix and order quantity.

Devis Contact
LT3669EUFD-2#TRPBF - IO-Link Transceiver with Dual Regulators
LT3669EUFD-2#TRPBF

LT3669EUFD-2#TRPBF - IO-Link Transceiver with Dual Regulators

The Analog Devices LT3669EUFD-2#TRPBF is a 1/1 IO-Link industrial transceiver with an integrated step-down switching regulator and low-dropout regulator, housed in a 28-lead 4 mm by 5 mm QFN package. The verified product data identifies the device for surface mounting and reel-and-tape handling, with an operating temperature range of -40°C to 125°C. Its integrated power architecture supports the sensor-side requirements of IO-Link industrial connections while reducing the number of external supply components. An IO-Link transceiver is an interface IC that connects a microcontroller or PLC-side controller to an industrial point-to-point sensor or actuator link. IO-Link adds standardized digital communication and wake-up or power-control capabilities beyond a conventional simple sensor output. The LT3669 family combines that physical-layer interface with power-conversion functions, placing the transceiver, switching regulator, and LDO in one package. Verified features include 1/1 transceiver operation, IO-Link functionality, integrated step-down regulation, integrated LDO operation, wake-up detection, and a programmable power-on reset timer for the LT3669 family. The Analog Devices LT3669-2 is listed for up to 300 mA load current and requires an external catch diode, whereas the LT3669 variant integrates the catch diode and is listed for up to 100 mA load current. The 28-QFN (4x5) exposed-pad package is designed for surface-mount assembly and can provide a compact solution where both signal interface and local power conversion are required. The exposed pad also supports thermal conduction into the PCB, although actual thermal performance depends on copper area, board construction, ambient temperature, and load. Use the manufacturer datasheet for pin functions, recommended external components, electrical limits, timing, and layout details before finalizing a design. Typical applications include IO-Link sensors, industrial proximity and level sensors, factory automation equipment, PLC-connected actuators, and other 24 V industrial fieldbus nodes. The LT3669EUFD-2#TRPBF is most appropriate when a compact 28-QFN footprint, integrated regulators, and the LT3669-2 external-catch-diode architecture fit the system specification. Design attention should focus on correct pin mapping, regulator stability, catch-diode selection, exposed-pad thermal management, and separation between sensitive communication traces and switching-power paths. The verified distributor record identifies the part as a 28-QFN (4x5) IO-Link transceiver, but detailed application limits and package dimensions must be confirmed from the official Analog Devices documentation. This product data combines the verified manufacturer and distributor identity, package information, family-level functional description, commercial source links, and practical design guidance into an engineering-oriented reference for IO-Link transceiver and power-management design.

Devis Contact
LT3669HUFD#PBF - 40V IO-Link Interface | Analog Devices
LT3669HUFD#PBF

LT3669HUFD#PBF - 40V IO-Link Interface | Analog Devices

The Analog Devices LT3669HUFD#PBF is an industrial IO-Link transceiver with integrated 16 V step-down and 150 mA LDO functions, operating from a 7.5 V to 40 V supply in a 28-pin QFN package. It combines one IO-Link physical-layer channel, protected line-driver outputs, wake-up detection, and a programmable power-on reset timer. The verified product information identifies ±60 V cable-interface protection and rugged line drivers for industrial sensor and actuator cabling. An IO-Link transceiver is an interface IC that connects a microcontroller or sensor hub to an industrial point-to-point cable while combining digital communication and power delivery. In the hierarchy, the LT3669 is an IO-Link interface transceiver with integrated DC-DC converter and LDO. That integration reduces the number of separate supply blocks needed at a remote industrial sensor, actuator, or factory I/O node while retaining communication and power management in one device. The main feature set includes compatibility with COM1, COM2, and COM3, operation from 40 V, a 16 V step-down switching-regulator output, an integrated 150 mA low-dropout regulator, and ±60 V cable-interface protection. Wake-up detection supports systems that must detect activity on a connected cable. A programmable power-on reset timer provides controlled startup behavior for downstream circuitry, which is useful when load power must become valid only after timing requirements are met. Technically, the part combines three functional blocks in one surface-mount device: an IO-Link physical layer, a step-down switching regulator, and an LDO. The integrated supply architecture is especially useful in industrial systems where a higher-voltage bus powers a lower-voltage sensor. Its stated −40 °C to 150 °C operating range for the H-grade comparison result broadens environmental suitability, but designers should confirm all limits and derating requirements against the manufacturer datasheet before release. Typical applications include IO-Link sensor masters, proximity and photoelectric sensors, industrial actuator interfaces, factory automation equipment, remote I/O modules, and motor or process-control systems. The single-transceiver configuration is appropriate when one cable segment must carry IO-Link data while receiving local regulated power. Design the printed-circuit board with short, protected cable-side traces and place input, switching-regulator, and LDO capacitors according to the manufacturer layout guidance. Validate startup sequencing, exposed-pad thermal performance, surge operation, and fault behavior across the complete industrial supply and cable transient range. This page consolidates verified manufacturer and distributor information, documented alternatives, interface functions, and design cautions into a procurement-oriented engineering reference without inferring unverified electrical or pin-level details.

Devis Contact
LT3669HUFD#TRPBF - Integrated IO-Link Power | Analog Devices
LT3669HUFD#TRPBF

LT3669HUFD#TRPBF - Integrated IO-Link Power | Analog Devices

The Analog Devices LT3669HUFD#TRPBF is a single-channel industrial IO-Link transceiver with an integrated step-down switching regulator and low-dropout linear regulator, housed in a 28-pin QFN package with an exposed pad. The verified product data identifies a 4 mm by 5 mm package, while detailed operating, current, voltage, timing, and pin-function values were not included in the supplied records and must be confirmed in the manufacturer datasheet. An IO-Link transceiver is a specialized industrial interface that combines a physical-layer data channel with sensor or actuator support circuitry. This device additionally manages local power requirements, making it useful when an IO-Link node needs both communications and regulated power without using separate power-conversion stages. In system terms, it belongs to the interface-IC hierarchy while also incorporating DC-DC converter and linear-regulator functions. The LT3669 family is described by Analog Devices as an industrial transceiver with an integrated step-down regulator, LDO, wake-up detection, and a programmable power-on reset timer. The transmitter current limit and slew rate are externally adjustable, allowing the designer to tune output behavior for the connected IO-Link master, cable, load, and application timing. These functional details distinguish it from a basic digital line-driver or receiver. The LT3669 family is available in LT3669 and LT3669-2 versions, with LT3669-2 identified by the manufacturer as recommended for new designs. The supplied distributor record confirms that the target is supplied in a 28-QFN 4 mm by 5 mm surface-mount package. The exposed thermal pad should be connected according to the datasheet land pattern and thermal recommendations rather than treated as an unused pin. Typical uses include industrial IO-Link sensor interfaces, factory automation nodes, proximity and light-sensor links, actuator connections, and compact industrial control modules. The integrated regulators can simplify power partitioning, while the transceiver supports communication between a master and an IO-Link-compatible peripheral. Actual operating limits and timing must be checked against the complete datasheet before design release. For robust implementation, preserve the recommended input and output capacitors, follow the exposed-pad land pattern, validate adjustable current-limit and slew-rate settings, and check reset or wake-up timing against the system power sequence. This page combines verified manufacturer and distributor information with explicit data-gap markers rather than estimating electrical performance. This page consolidates verified sourcing, package information, lifecycle guidance, application context, and replacement guidance that are not consolidated in a raw distributor listing. LT3669 family options are distinguished carefully, while unverified competitor equivalents are excluded.

Devis Contact
LT3669HUFD-2#PBF - Integrated IO-Link Interface | Analog Devices
LT3669HUFD-2#PBF

LT3669HUFD-2#PBF - Integrated IO-Link Interface | Analog Devices

The Analog Devices LT3669HUFD-2#PBF is an industrial IO-Link transceiver with an integrated step-down switching regulator and low-dropout linear regulator, supplied in a 28-lead 4 mm by 5 mm plastic QFN package. The verified product information identifies its interface supply range as 7.5 V to 40 V. The LT3669-2 version supports a switching-regulator load current up to 300 mA and requires an external catch diode, unlike the base LT3669 version, which integrates the catch diode and supports up to 100 mA. An IO-Link transceiver is a specialized interface IC that connects an industrial sensor or actuator to a point-to-point IO-Link master. It combines the physical communication interface with local power-management functions, reducing the number of separate components required at the sensor end of an industrial link. This device also includes wake-up detection and a programmable power-on reset timer for managed sensor power behavior. Key features include the integrated step-down regulator, integrated LDO, IO-Link communication, wake-up detect, programmable power-on reset, and operation from a 7.5 V to 40 V interface supply. The LT3669-2 configuration is intended for designs requiring the higher 300 mA switching-regulator load capability. Its 28-QFN package is compact but requires careful layout and exposed-pad thermal management. According to the manufacturer product page, the LT3669 and LT3669-2 are recommended for new designs. The manufacturer also identifies the LT3669-2 as requiring an external catch diode, making circuit implementation distinct from the original LT3669. The available verified source set does not provide a complete electrical limit table, pin-by-pin mapping, compliance declarations, or pricing tiers beyond the manufacturer's listed starting price. Typical uses include proximity sensors, photoelectric sensors, industrial actuators, decentralized IO-Link sensor nodes, factory automation equipment, and other 24 V industrial sensing systems. The local regulators can power sensor electronics while the transceiver handles wake-up communication with the IO-Link master. When designing the circuit, follow the manufacturer datasheet for the external catch diode, inductor, capacitors, exposed-pad layout, and decoupling values. Treat the 4 mm by 5 mm QFN thermal pad as a heat-spreading structure and verify copper area, via count, and temperature rise against the actual regulator dissipation. This page combines verified manufacturer and distributor information with replacement evidence, interface guidance, and design cautions that are not consolidated on a basic distributor listing. It separates confirmed LT3669-2 differences from specifications that still require the complete datasheet or design-specific validation.

Devis Contact
LT3669HUFD-2#TRPBF IO-Link Transceiver | Analog Devices
LT3669HUFD-2#TRPBF

LT3669HUFD-2#TRPBF IO-Link Transceiver | Analog Devices

The Analog Devices LT3669HUFD-2#TRPBF is a single-transceiver industrial IO-Link interface IC with an integrated step-down switching regulator and low-dropout regulator (LDO), supplied in a 28-QFN package measuring 4 mm by 5 mm. The verified product data identifies it as a 1/1 IO-Link transceiver, while the manufacturer describes the LT3669-2 family as an industrial interface solution that supports wake-up detection and a programmable power-on-reset timer. An IO-Link transceiver is a specialized industrial interface device that combines a physical-layer communication channel with sensor and actuator support. IO-Link systems use point-to-point industrial connections for communication and power between a master and compatible sensors or actuators. The LT3669-2 integrates that interface function with local power conversion, reducing the number of separate supply blocks in an industrial sensor circuit. The LT3669-2 differs from the base LT3669 in its external power-path requirements. According to the manufacturer product page, the LT3669 integrates the catch diode and supports load current up to 100 mA, whereas the LT3669-2 requires an external catch diode and supports load current up to 300 mA. This distinction makes the -2 version appropriate when the local regulator output must deliver more current, provided the external diode and associated layout requirements are implemented correctly. Wake-up detect functionality helps the interface recognize activity on the connected line, while the programmable power-on-reset timer provides a defined startup delay for system sequencing. These features are relevant to industrial sensors where deterministic initialization, controlled sensor energization, and robust point-to-point communication are required. The integrated step-down regulator and LDO can support local sensor-power and interface-power requirements when the board-level voltage plan and thermal limits are properly designed. Typical IO-Link applications include proximity sensors, photoelectric sensors, pressure and temperature sensing modules, industrial actuator interfaces, and factory-automation equipment. The single-transceiver arrangement is particularly useful for compact sensor nodes that require a communication interface and regulated auxiliary power without a separate communications transceiver. Layout and power design remain critical. Place the catch diode and energy-storage components exactly as required by the manufacturer application guidance, and verify the exposed-pad thermal path when the 300 mA version operates near its maximum documented load. The package designation uses a QFN footprint, so the PCB land pattern, exposed-pad soldering, and pin numbering should be checked against the manufacturer datasheet before release to manufacturing. This product page combines verified distributor and manufacturer information with engineering guidance for IO-Link and industrial sensor designs.

Devis Contact
LT3669IUFD#PBF - IO-Link Transceiver with Buck/LDO | Analog Devices
LT3669IUFD#PBF

LT3669IUFD#PBF - IO-Link Transceiver with Buck/LDO | Analog Devices

The Analog Devices LT3669IUFD#PBF is an industrial IO-Link transceiver with an integrated step-down switching regulator, a low-dropout linear regulator, wake-up detection, and a programmable power-on reset timer, housed in a 28-pin QFN exposed-pad package. The verified source data confirms a 7.5 V to 40 V supply range and an operating temperature range of -40 C to +125 C. It combines sensor-interface and local power functions in one device. An IO-Link transceiver is the interface between an industrial sensor or actuator and a point-to-point industrial communications link. The LT3669 provides the physical signaling path while integrating power-conversion functions for the connected equipment. This combination can reduce the number of discrete interface and power-supply components in sensor modules, compact control blocks, and industrial field devices. The LT3669 is designed around three functional blocks identified by Analog Devices: an IO-Link transceiver, a step-down regulator, and an LDO. It also includes wake-up detect functionality and a programmable power-on reset timer. The transmitter current limit and slew rate are externally adjustable, allowing the application to tune communication behavior and power-delivery characteristics. The supplied manufacturer information also identifies the LT3669 family as recommended for new designs. Typical industrial uses include IO-Link sensor interfaces, proximity and limit sensors, industrial actuator modules, factory automation equipment, and embedded control systems that need local power alongside a communications transceiver. The integrated architecture can simplify board partitioning, but each rail and signal path still requires careful decoupling, grounding, protection, and thermal review. The exact output-current, switching-frequency, dropout, and timing limits are not present in the supplied verified excerpts and must be confirmed from the complete manufacturer datasheet before production design. When laying out this QFN device, place input, output, and interface decoupling components close to their associated pins, connect the exposed pad to the appropriate thermal and ground plane, and keep sensitive signal routing away from switching-current paths. Verify wake-up and power-on reset timing with the complete electrical specification. The product is available in a tube package according to the verified distributor listing. This product page combines the verified Analog Devices product information, distributor package and sourcing references, and practical design guidance for engineers evaluating the LT3669 in IO-Link systems.

Devis Contact
LT3669IUFD#TRPBF - IO-Link Transceiver with Buck/LDO
LT3669IUFD#TRPBF

LT3669IUFD#TRPBF - IO-Link Transceiver with Buck/LDO

The Analog Devices LT3669IUFD#TRPBF is an industrial IO-Link transceiver integrating a step-down switching regulator, a low-dropout linear regulator, wake-up detection, and a programmable power-on reset timer. The device is supplied in a 28-pin QFN exposed-pad package measuring 4 mm by 5 mm, combining sensor-interface and local power functions in one device. An IO-Link transceiver is an interface IC that connects industrial sensors and actuators to a point-to-point communications link. It combines physical-layer signaling with supporting functions that help the connected equipment operate reliably in factory automation, sensors, and industrial control systems. The LT3669 belongs to the transceiver and interface-IC hierarchy, while its integrated regulator sections place it at the intersection of communications, power management, and industrial automation. The verified manufacturer description identifies a single-transmitter, single-receiver industrial interface with an integrated step-down regulator and LDO. Wake-up detect functionality supports sensor activation, while the programmable power-on reset timer provides a defined startup delay. The transmitter current limit and slew rate are externally adjustable, allowing the interface behavior to be matched to the wiring, capacitance, and protection requirements of a particular sensor or actuator. Combining the IO-Link physical interface, switching regulator, and LDO can reduce the number of discrete power-support components in a compact sensor design. It is particularly relevant where a sensor needs both a communication link and local regulated power. The integrated regulators also require careful layout because switching-node, analog-ground, and exposed-pad connections must be managed according to the manufacturer datasheet. Typical uses include industrial proximity and process sensors, actuator modules, factory automation equipment, and IO-Link-compatible control systems. The 28-QFN exposed-pad package supports compact placement but requires a controlled PCB land pattern and adequate thermal copper. Design engineers should verify the complete electrical limits, recommended external components, pin names, and application circuit from the official Analog Devices datasheet before production release. This page consolidates the verified manufacturer and distributor information for the LT3669IUFD#TRPBF, identifies the available family alternatives, and highlights practical package and selection considerations. For pricing, use the listed distributor references as of 2026-10-23 and confirm live stock, lead time, and configuration before purchasing.

Devis Contact
LT3669IUFD-2#PBF - 40V IO-Link Transceiver | Analog Devices
LT3669IUFD-2#PBF

LT3669IUFD-2#PBF - 40V IO-Link Transceiver | Analog Devices

The Analog Devices LT3669IUFD-2#PBF is an industrial IO-Link transceiver with an integrated step-down switching regulator and low-dropout regulator, a 7.5V to 40V operating range, and support for load currents up to 300mA, all in a 28-QFN surface-mount package. An IO-Link transceiver is an interface IC that connects sensors and actuators to an industrial point-to-point communication link. It combines physical-layer signaling with device power delivery, allowing one integrated module to handle both command communication and a regulated supply. The IO-Link transceiver category sits below industrial interface ICs, while the integrated switching and linear regulators place this device within broader industrial power-management and sensor-interface systems. The LT3669-2 variant supports a 300mA regulator load, whereas the LT3669 integrates a catch diode for operation up to 100mA and the LT3669-2 requires an external catch diode. Wake-up detection and a programmable power-on reset timer support robust industrial sensor behavior. Adjustable transmitter current limit and slew rate provide additional control over physical-layer signal behavior and system integration. The integrated power architecture reduces the number of separate supply components required by an IO-Link sensor module. Its step-down regulator produces a lower sensor-side voltage from the industrial input rail, while the LDO provides a clean regulated output where required. The manufacturer identifies LT3669 and LT3669-2 as being recommended for new designs, making them relevant to current industrial sensing and factory-automation platforms. Typical uses include proximity sensors, photoelectric sensors, industrial actuator interfaces, factory automation equipment, and IO-Link masters or sensor modules operating from protected industrial supplies. The device is particularly useful when the interface must support communication and regulated sensor power in one compact package. Designers should follow the datasheet exactly for the external catch diode, inductor, capacitors, current-limit setting, slew-rate setting, and wake-up or reset configuration. The external diode and regulator layout directly affect reliability, efficiency, and emissions, so PCB layout should follow the manufacturer’s recommended application circuit rather than relying on generic regulator guidance. This page combines verified manufacturer and distributor information, same-package alternatives, interface distinctions, pricing references, and practical engineering guidance. It also separates verified LT3669-2 facts from specifications that still require direct datasheet confirmation.

Devis Contact
LT3669IUFD-2#TRPBF - IO-Link Transceiver | Analog Devices
LT3669IUFD-2#TRPBF

LT3669IUFD-2#TRPBF - IO-Link Transceiver | Analog Devices

The Analog Devices LT3669IUFD-2#TRPBF is an industrial IO-Link transceiver integrating one transmitter, one receiver, a step-down switching regulator, and a low-dropout regulator in a 28-pin QFN package. It supports a 7.5 V to 40 V supply range and operates from -40°C to +125°C. The -2 variant supports up to 300 mA step-down load current and requires an external catch diode, while the related LT3669 integrates the catch diode for operation up to 100 mA. An IO-Link transceiver is an industrial sensor-interface device that connects compatible sensors, actuators, and master ports over an IO-Link communication link. In the signal path, the integrated receiver detects and conditions incoming IO-Link data, while the transmitter drives the output. The device also provides wake-up detect functionality and a programmable power-on reset timer, reducing the need for separate interface and supervisory circuitry. The most distinctive feature is integration of an IO-Link transceiver with local power conversion. The step-down regulator supplies a lower-voltage rail for sensor or actuator electronics, while the LDO provides a low-dropout output from that rail. In the LT3669IUFD-2#TRPBF, external rectification is required, and the supported switching-regulator load is up to 300 mA. The transmitter current limit and slew rate are externally adjustable, allowing engineers to tune output behavior for a particular line, load, or electromagnetic-compatibility requirement. Operation from -40°C to +125°C suits industrial automation, factory sensors, actuator nodes, and equipment operating across wide temperature ranges. A 40 V maximum supply also provides headroom above conventional 24 V industrial buses, although system transients still require suitable protection. The 28-QFN exposed-pad package is intended for surface-mount assembly and benefits from a properly designed ground and thermal layout. Design attention should focus on the required external catch diode, regulator compensation or output capacitors specified by the manufacturer, exposed-pad soldering, and IO-Link line protection. Because the -2 and non--2 LT3669 versions differ in their integrated catch-diode arrangement and supported regulator load, verify the exact schematic before substitution. The product page identifies the LT3669-2 as recommended for new designs. This page combines verified manufacturer and distributor information with practical selection guidance, function-level application analysis, and explicit data gaps for unverified electrical details. Engineers should consult the complete manufacturer datasheet before setting operating voltages, timing, compensation, current limits, or protection networks.

Devis Contact
LT3960EMSE#PBF - 400kbps I2C-to-CAN Transceiver | Analog Devices
LT3960EMSE#PBF

LT3960EMSE#PBF - 400kbps I2C-to-CAN Transceiver | Analog Devices

The Analog Devices LT3960EMSE#PBF is a robust 400kbps I2C-to-CAN physical-layer transceiver with one transmitter and one receiver, protected against overvoltage line faults, and supplied in a 10-lead MSOP exposed-pad package. It supports a 60V power-supply range, a selectable internal 3.3V regulator or 5V bus-voltage operation, and extended CAN-compatible common-mode reception. An I2C-to-CAN transceiver is an interface IC that bridges a logic-level I2C connection and a differential, fault-tolerant CAN physical bus. This bridge belongs to the CAN interface hierarchy and allows a single-master I2C bus to communicate across noisy or electrically harsh cable distances where direct I2C wiring would be unsuitable. One LT3960 is normally placed near the I2C master, while another device near the remote CAN endpoint completes the link. Key verified features include communication at up to 400kbps, protection from CAN line overvoltage faults, operation from a 60V power-supply range, and the option to use the internal 3.3V regulator or a 5V bus voltage. The CAN-compatible differential receiver has a common-mode range of ±25V or ±36V depending on VCC. These characteristics support reliable separation between sensitive local electronics and a remote, high-noise bus. The LT3960 converts SCL and SDA activity into equivalent differential CAN-bus behavior while permitting bidirectional communication. Its CAN physical layer is designed for robust links, but system designers must still provide correct termination, grounding, surge protection, and decoupling. The exposed pad improves heat transfer, although actual self-heating depends on supply voltage, bus state, and ambient conditions. Typical uses include industrial remote I2C monitoring, building-control equipment, factory sensor links, test systems, and CAN-connected data-acquisition modules. The LT3960 is particularly useful when an embedded controller has an I2C master port but the system requires a longer, noise-isolated connection to remote equipment. The principal design consideration is preserving interface timing and logic levels across the transceiver pair. Follow the manufacturer data sheet together with the EVAL-LT3960-AZ user guide, and verify that the selected supply and common-mode conditions match the installed system. This page consolidates verified manufacturer information, distributor pricing, sourcing links, and application guidance for engineers evaluating the LT3960EMSE#PBF.

Devis Contact
LT3960EMSE#TRPBF - 400kbps I2C-to-CAN Transceiver | ADI
LT3960EMSE#TRPBF

LT3960EMSE#TRPBF - 400kbps I2C-to-CAN Transceiver | ADI

The Analog Devices LT3960EMSE#TRPBF is a 400 kbps I2C-to-CAN physical-layer transceiver with bidirectional data communication, 60 V power-supply range, and a 10-lead MSOP exposed-pad package. It is designed to extend a single-master I2C bus through harsh or noisy environments while preserving communication between SCL and SDA signals. A CAN transceiver is an interface circuit that converts logic-level signals into a physical differential bus and receives bus states back into logic-level signals. The LT3960 uses the CAN physical layer as a rugged transport mechanism for an I2C-style single-master bus. Its protected line-fault inputs, extended common-mode capability, and internal regulator support integration where the I2C master and remote bus-powered nodes are separated by substantial cable distance or electrical noise. Key verified features include operation up to 400 kbps, compatibility with 3.3 V and 5 V systems, protection from overvoltage line faults, and an internal 3.3 V regulator or selectable 5 V bus-voltage operation. Bidirectional communication is permitted, allowing data signals to flow between the host-side interface and the bus-side transceiver. The manufacturer identifies the LT3960EMSE as a 10-lead MSOP package, while the orderable LT3960EMSE#TRPBF suffix identifies the leaded RoHS-compliant packaging configuration. The device is supplied from a single wide-ranging input supply, reducing system power-tree complexity when the interface must operate near higher-voltage industrial or automotive-related equipment. Its physical-layer approach is intended for extending a bus rather than replacing a conventional CAN controller. Designers should account for the MSOP exposed pad, line termination, common-mode environment, cable length, grounding, and the different logic and bus-side voltage domains. Typical applications include industrial sensor links, remote instrumentation, building-automation equipment, noisy factory communication, and embedded systems that need I2C traffic to cross an electrically hostile cable. The verified manufacturer page specifically references the EVAL-LT3960-AZ evaluation circuit, which is useful for validating board routing, bus termination, and system behavior. For PCB design, place the transceiver near the cable connector and preserve a controlled return path to reduce common-mode conversion. Confirm the exposed-pad connection and thermal pad layout against the manufacturer package drawing. Do not substitute a conventional CAN transceiver without checking logic-side voltage, timing, fault behavior, and pin compatibility. This page combines the verified Analog Devices product information with practical interface-design guidance. It distinguishes the LT3960 from ordinary CAN controllers, emphasizes the 400 kbps single-master I2C role, and identifies which electrical details must be confirmed in the datasheet before layout release.

Devis Contact