Produits (39 000+)

LT3960JMSE#PBF - 400kbps I2C-to-CAN Transceiver | ADI
LT3960JMSE#PBF

LT3960JMSE#PBF - 400kbps I2C-to-CAN Transceiver | ADI

The Analog Devices LT3960JMSE#PBF is a single I2C-to-CAN physical-layer transceiver supporting I2C communication up to 400 kbps, supplied from a 3.3 V or 5 V range, and packaged in a 10-pin MSOP with exposed pad. It converts one I2C master bus into differential CAN-compatible signaling across a long or noisy interconnect, providing one driver and one receiver. An I2C-to-CAN transceiver is an interface IC that bridges the short-range, controller-oriented I2C bus and the CAN physical layer. It extends a single-master I2C connection through a harness or harsh electrical environment while preserving a familiar logic-side interface. In the system hierarchy, this device is an interface transceiver within CAN interface ICs and broader wired-communication semiconductors. The verified information identifies 400 kbps I2C communication, a 60 V power-supply range, and internal 3.3 V operation. It also confirms protection from overvoltage line faults. The LT3960 family is intended for industrial communication, and the manufacturer states that LT3960J performance is guaranteed from -40°C to 150°C operating junction temperature; the broader datasheet also describes -40°C to 125°C operating-temperature assurance. The receiver is a CAN-compatible differential receiver with a wide common-mode range of plus or minus 25 V or plus or minus 36 V, depending on VCC. In a typical two-device arrangement, one LT3960 is placed near the I2C master and the other near the distant endpoint. This arrangement keeps sensitive logic connections local while using the CAN physical layer for the longer link. Typical uses include industrial sensor links, factory automation equipment, building-control modules, remote I/O nodes, and embedded systems that need an I2C master to communicate across a longer cable. Use the exposed-pad land pattern for thermal and electrical performance, and observe the manufacturer's pin and layout guidance. A key design consideration is that the LT3960 is a transceiver, not a general-purpose CAN controller. The connected microcontroller must generate the appropriate bus behavior and protocol, while the LT3960 provides the physical signaling interface. Verify voltage ratings, termination, grounding, and fault conditions against the manufacturer datasheet. This page combines verified distributor and manufacturer information with package, application, and design guidance intended to support faster sourcing and design review.

Devis Contact
LT3960JMSE#TRPBF - 400kbps I2C/CAN Transceiver | Analog
LT3960JMSE#TRPBF

LT3960JMSE#TRPBF - 400kbps I2C/CAN Transceiver | Analog

The Analog Devices LT3960JMSE#TRPBF is a half-duplex I2C-to-CAN physical-layer transceiver rated for data rates up to 400 kbps, supplied in a 10-pin MSOP with an exposed pad. It operates from 3.3 V or 5 V, supports I2C communication over harsh or noisy environments, and provides CAN-compatible differential signaling with protection against overvoltage line faults. The part is intended for remote sensing, industrial control, and distributed I2C-to-CAN gateway designs. An I2C-to-CAN transceiver is an interface IC that translates the logic-level clock and data signals of a single-master I2C bus into a differential CAN physical-layer signal. The LT3960 extends that bus beyond a local circuit board, using two devices in a typical system: one connects near the I2C master, while the other provides the remote endpoint. This architecture preserves the familiar I2C host interface while gaining the noise immunity and fault tolerance associated with CAN cabling. Key verified features include operation up to 400 kbps, compatibility with both 3.3 V and 5 V systems, a 60 V power-supply range for the CAN-side protection circuitry, and internal 3.3 V regulation. The receiver has a wide common-mode range of ±25 V or ±36 V depending on VCC. The LT3960 is designed for extended temperature-grade industrial environments; the manufacturer states that LT3960J performance is assured over a -40 °C to 150 °C operating junction range. The exposed-pad MSOP package helps remove heat from the device when the CAN-side dissipation is significant. Placement should keep the transceiver close to the connector or cable entry, while the I2C master and local digital ground connections should remain isolated from the harsher CAN return path as appropriate. CAN termination and common-mode behavior must be evaluated for the complete bus rather than inferred from the IC alone. Typical applications include remote sensor nodes, industrial monitoring links, building-control gateways, actuator networks, and embedded systems that need to extend I2C across a noisy cable. The 400 kbps rate is suitable for moderate-speed control and telemetry traffic, not high-bandwidth data transfer. The device should be selected only when its CAN common-mode, fault-protection, supply, and thermal characteristics match the target bus. The most important design check is system-level compatibility: verify the 3.3 V or 5 V I2C levels, cable length and topology, termination strategy, grounding, and the maximum junction temperature. The LT3960’s protected CAN interface can simplify remote-bus deployment, but it does not eliminate the need for correct bus protection and wiring. This page combines verified manufacturer and distributor information with application guidance, comparison parameters, and practical implementation notes. Pricing and availability references are current only as of 2026-10-23; verify distributor stock and delivery terms before ordering.

Devis Contact
LT6222 - Quad 60MHz Rail-to-Rail Op Amp | Analog Devices
LT6222

LT6222 - Quad 60MHz Rail-to-Rail Op Amp | Analog Devices

The LT6222 is a quad, low power, high speed rail-to-rail input and output operational amplifier from Analog Devices (formerly Linear Technology). It features a gain bandwidth product of 60MHz, a slew rate of 20V/μs, and a low quiescent current of 1mA per amplifier (max). The device operates from a supply voltage range of 2.2V to 12.6V, making it suitable for battery-powered and low-voltage applications. The LT6222 is available in a 16-lead SSOP package, providing a compact solution for space-constrained designs. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output. It is a fundamental building block in analog electronics, used in signal conditioning, filtering, and amplification. The LT6222 belongs to the family of precision op amps, which are characterized by low offset voltage, low bias current, and high DC gain. In the hierarchy of analog ICs, op amps fall under linear regulators and amplifiers, which are part of the broader category of analog and mixed-signal integrated circuits. Key features of the LT6222 include rail-to-rail input and output swing, which maximizes dynamic range in low-supply applications. The input common mode range includes both rails, and the output swings rail-to-rail, allowing the amplifier to operate with supply voltages as low as 2.2V. The device also offers low broadband voltage noise of 4.2nV/√Hz, making it suitable for low-noise signal processing. Additionally, the LT6222 includes a power-down feature that reduces supply current to a shutdown mode, conserving power in portable devices. Technically, the LT6222 uses a complementary bipolar process that achieves high speed and low power simultaneously. The amplifier's DC performance is excellent, with low input offset voltage and high open-loop gain, ensuring accurate signal amplification. The device is specified over the industrial temperature range of -40°C to 85°C, and it is available in both commercial and industrial grades. The LT6222 is designed to be a plug-in replacement for many standard op amps, improving input/output range and performance. Typical applications include active filters, data acquisition systems, battery-powered instrumentation, and portable medical devices. The rail-to-rail output allows direct interfacing to ADCs, while the low noise and high speed make it ideal for signal conditioning in communication systems. The power-down feature is particularly useful in battery-operated equipment where power conservation is critical. When designing with the LT6222, ensure proper decoupling of the power supply pins with 0.1μF ceramic capacitors placed close to the device. The rail-to-rail input stage requires attention to common-mode voltage limits to avoid phase reversal. For optimal performance, use a ground plane and minimize parasitic capacitance on the input nodes.

Devis Contact
LT6222CDD#PBF - 60MHz Low Power R2R Op Amp | Analog Devices
LT6222CDD#PBF

LT6222CDD#PBF - 60MHz Low Power R2R Op Amp | Analog Devices

The LT6222CDD#PBF is a quad, low power, high speed rail-to-rail input and output operational amplifier from Analog Devices (formerly Linear Technology). It is part of the LT6220/LT6221/LT6222 family, which offers excellent DC performance with reduced supply current and lower input offset voltage. The LT6222CDD#PBF operates from a supply voltage range of 2.2V to 12.6V, features a gain-bandwidth product of 60MHz, and a slew rate of 20V/µs. It is available in a 16-pin DFN package (4x3mm) and is specified for the commercial temperature range (0°C to 70°C). An operational amplifier (op-amp) is a high-gain voltage amplifier with differential inputs and a single-ended output. It is a fundamental building block in analog electronics, used in signal conditioning, filtering, and amplification. The LT6222CDD#PBF is a rail-to-rail input and output op-amp, meaning its input common-mode range and output swing can reach both supply rails, maximizing dynamic range in low-voltage applications. This makes it suitable for battery-powered and portable devices where headroom is limited. Key features of the LT6222CDD#PBF include a low supply current of 1mA per amplifier, a low input offset voltage of 100µV (max), and a high open-loop gain of 100dB. The rail-to-rail input and output capability allows it to operate with supply voltages as low as 2.2V, making it ideal for single-supply applications. The device also features a wide bandwidth of 60MHz and a high slew rate of 20V/µs, enabling it to handle fast signals in video and communication systems. The LT6222CDD#PBF uses a complementary bipolar process technology, which provides excellent DC precision and AC performance. The device is designed for low power consumption without compromising speed, making it suitable for battery-powered instrumentation and portable audio equipment. Its high input impedance and low bias current make it suitable for interfacing with high-impedance sensors. Typical applications include active filters, data acquisition systems, portable instrumentation, and audio signal conditioning. The quad configuration allows multiple amplifier stages in a single package, saving board space and reducing component count. The rail-to-rail output swing ensures maximum signal amplitude in low-voltage systems. When designing with the LT6222CDD#PBF, ensure proper power supply decoupling with 0.1µF ceramic capacitors close to the supply pins. The input common-mode range extends to both rails, but for best performance, keep inputs within the specified range. The output can drive capacitive loads up to 100pF without oscillation, but for larger loads, a series resistor may be needed.

Devis Contact
LT6222CS8#PBF - Quad 60MHz Rail-to-Rail Op Amp | Analog Devices
LT6222CS8#PBF

LT6222CS8#PBF - Quad 60MHz Rail-to-Rail Op Amp | Analog Devices

The LT6222CS8#PBF is a quad, low power, high speed rail-to-rail input and output operational amplifier from Analog Devices. It features a gain bandwidth product of 60 MHz and a slew rate of 20 V/µs, making it suitable for a wide range of signal conditioning applications. The device operates from a supply voltage range of 2.2V to 12.6V (or ±1.1V to ±6.3V) and is available in an 8-lead SOIC package. The LT6222 is part of the LT6220/LT6221/LT6222 family, which offers reduced supply current, lower input offset voltage, and lower input bias current compared to many standard op amps. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output. It is a fundamental building block in analog electronics, used in applications such as filtering, amplification, and signal conditioning. Op amps are categorized within the broader hierarchy of linear integrated circuits, which also includes comparators, voltage regulators, and analog-to-digital converters. The rail-to-rail input and output capability of the LT6222 allows the output to swing close to the supply rails, maximizing dynamic range in low-voltage applications. Key features of the LT6222CS8#PBF include rail-to-rail input and output, a 60 MHz gain bandwidth product, a 20 V/µs slew rate, and low power consumption. The device also offers excellent DC performance, including low input offset voltage and low input bias current. These specifications make it ideal for high-speed signal processing, portable instrumentation, and battery-powered equipment where power efficiency and signal integrity are critical. The LT6222 utilizes a complementary bipolar process technology, which provides a good balance between speed, noise, and power consumption. The device is designed to operate over the commercial temperature range of 0°C to 70°C. Its low supply current of typically 1.2 mA per amplifier helps extend battery life in portable applications. The rail-to-rail output stage ensures maximum output swing, which is particularly beneficial in single-supply applications. Typical applications for the LT6222CS8#PBF include active filters, data acquisition systems, audio processing, and portable instrumentation. Its high slew rate and bandwidth make it suitable for driving analog-to-digital converters (ADCs) and buffering reference voltages. The device can also be used in communication systems, such as base station receivers and transmitters, where high-speed signal conditioning is required. When designing with the LT6222, it is important to ensure proper power supply decoupling. Place a 0.1 µF ceramic capacitor close to each supply pin to minimize high-frequency noise. Additionally, consider the input common-mode voltage range, which extends to the rails, to avoid unexpected saturation. The output can drive capacitive loads up to 100 pF without oscillation, but for larger loads, a series resistor may be needed.

Devis Contact
LT685CH - 5.5ns ECL High-Speed Comparator | Analog Devices
LT685CH

LT685CH - 5.5ns ECL High-Speed Comparator | Analog Devices

The Analog Devices LT685CH is an ultrafast high-speed comparator with differential inputs, complementary ECL-compatible outputs, and a typical propagation delay of 5.5 ns, supplied in an 8-pin hermetic ceramic DIP package. Its output current capability is suitable for driving 50 ohm transmission lines, while low input offset and high resolution support precision analog-to-digital signal processing. The device also provides an output latch function and an external hysteresis control pin. A high-speed comparator is a signal-conditioning integrated circuit that compares two input voltages and changes its output state according to their relative polarity. The LT685 belongs to the comparator hierarchy within interface and signal-processing semiconductors. Its differential inputs reduce sensitivity to common-mode noise when the compared signals are balanced, while complementary outputs simplify interfacing with ECL-family logic and systems requiring both true and inverted decisions. The LT685CH emphasizes decision speed rather than rail-to-rail input operation or low power consumption. According to the manufacturer product information, the device is fully compatible with ECL logic levels and can adequately drive transmission lines terminated in 50 ohms. The 5.5 ns typical delay is the principal performance figure for high-speed threshold detection. A dedicated latch function allows a decision to be held for downstream circuitry, and external hysteresis control helps designers set or tune the switching threshold behavior. Typical signal paths place the differential inputs close to the source and route them as a short, geometry-matched pair. Because the LT685CH is capable of high-speed output transitions, trace capacitance, impedance discontinuities, and ground-return paths can materially affect observed system performance. Terminated transmission lines should use the intended 50 ohm environment rather than long unterminated traces. The complementary ECL outputs also require careful common-grounding and interface compatibility with the receiving logic. The LT685CH is suited to analog-to-digital signal processing, pulse-width or timing measurements, threshold detection, waveform conditioning, and high-speed instrumentation. Its speed makes it useful when the decision result must arrive quickly, but circuit timing must include comparator delay, external hysteresis, interconnect delay, and receiving-device delay. The CH order suffix is treated as the specific packaged LT685CH variant; package dimensions, pin mapping, and full electrical limits require confirmation from the applicable manufacturer documentation. For PCB design, keep the input pair short, matched, and away from unrelated switching nodes. Place termination close to the driven output, provide a continuous ground reference, and avoid unnecessary stubs. If the output drives a cable or long trace, verify voltage levels and impedance before connecting to ECL inputs. Account for the latch and hysteresis controls during timing analysis rather than treating them as unused pins. This page consolidates the verified LT685 family description, available distributor references, package and lifecycle observations, and engineering guidance into one design-oriented resource. Because the supplied data does not expose a complete manufacturer parameter table or verified direct replacements, unverified electrical values and non-drop-in alternatives are explicitly not inferred.

Devis Contact
LT685CN - 5.5ns High-Speed ECL Comparator | Analog Devices
LT685CN

LT685CN - 5.5ns High-Speed ECL Comparator | Analog Devices

The Analog Devices LT685CN is an ultrafast high-speed comparator with a typical propagation delay of 5.5 ns, differential inputs, complementary ECL-compatible outputs, and a 16-pin PDIP package. It is designed for demanding analog-to-digital signal-processing and pulse-timing systems where fast decision time and direct transmission-line drive are important. The device also includes an output latch and an external hysteresis-control function. A comparator is an analog signal-processing semiconductor that evaluates two input voltages and produces a logic output indicating which input is higher. The LT685 belongs to the comparator hierarchy, where its differential inputs, complementary outputs, and ECL interface place it between general-purpose logic-level comparators and high-speed timing components used in instrumentation, communications, and data acquisition. The main features of the LT685CN include its 5.5 ns typical propagation delay, complementary ECL outputs, 50-ohm transmission-line drive capability, low input offset, output latch capability, and compatibility with the AM685 family. Its differential input structure supports balanced signal comparison, while the complementary outputs allow direct use in systems requiring both true and inverted decisions. The latch function can hold the comparator state for applications that need sampled or stored decisions rather than continuous tracking. The LT685 uses an older high-speed ECL-compatible architecture intended for short propagation-delay operation and controlled point-to-point interconnects. Its output current capability is specified for driving transmission lines terminated in 50 ohms, making board-level routing and termination more important than with ordinary CMOS or TTL comparators. Differential inputs can also reduce sensitivity to common-mode noise when the surrounding analog signal path is properly laid out and referenced. Typical applications include pulse-width and pulse-height discrimination, high-speed threshold detection, ECL interface circuits, analog-to-digital front ends, communications equipment, laboratory instrumentation, and timing recovery systems. The 16-pin PDIP package is through-hole and suitable for legacy or prototype boards where the comparator must be inserted or socketed rather than mounted in a compact surface-mount assembly. When designing a circuit around the LT685CN, verify input common-mode range, output termination, supply requirements, latch timing, and the required propagation-delay margin. Keep high-speed traces short, use controlled impedance where practical, and terminate ECL-compatible outputs according to the system’s transmission-line topology. The available verified data does not establish exact input common-mode limits, supply-current values, pin-level timing, or package temperature limits. This product record combines the verified LT685 and LT685CN manufacturer information, distributor availability references, and cross-reference search results with practical guidance for high-speed comparator implementation. It also distinguishes documented drop-in alternatives from package or functional similarities so that engineers can make a replacement decision based on actual pin and parameter evidence.

Devis Contact
LTC1067IGN - Dual Switched-Cap Filter 20kHz | Analog Devices
LTC1067IGN

LTC1067IGN - Dual Switched-Cap Filter 20kHz | Analog Devices

The Analog Devices LTC1067IGN is a rail-to-rail, very low noise universal dual switched-capacitor filter building block that delivers two independent 2nd-order filter sections with cutoff frequencies up to 20 kHz in a 16-pin SSOP (narrow) package. Each filter section uses external resistors and the internal switched-capacitor architecture to implement low-pass, band-pass, notch, and all-pass responses. The device targets signal-conditioning applications where small footprint, low noise, and high dynamic range are mandatory. What is a switched-capacitor filter? A switched-capacitor filter is an active filter topology that emulates a resistor using a capacitor switched at a clock frequency, allowing precise, monolithic filter implementations without external precision capacitors. Within the broader IC taxonomy, switched-capacitor filters fall under active filters -> analog filters -> signal conditioning -> analog ICs -> semiconductors. They are preferred over continuous-time active filters for applications requiring tight frequency accuracy relative to an external clock. Key features include a clock-to-cutoff ratio of 100:1 (the LTC1067-50 variant uses 50:1), rail-to-rail input and output swing that maximizes dynamic range on low-voltage supplies, 60 dB signal-to-noise ratio, and a low noise floor suitable for instrumentation-grade signal chains. Each second-order block uses five external resistors, allowing independent configuration as a low-pass, high-pass, band-pass, or notch stage. Two blocks can be cascaded externally to build a 4th-order filter. The architecture is built on Analog Devices' precision switched-capacitor technology with CMOS analog switches and on-chip clock generation. The clock input accepts a TTL or CMOS external source, and the internal master clock divider sets the filter cutoff, simplifying design-in when synchronization to a system clock is required. The dual-block topology also enables independent filtering of two channels, such as stereo audio or dual-axis sensor signals, in a single IC. Typical applications include antialiasing filters for 16-bit ADCs, smoothing filters for DAC outputs, dual-channel audio crossover networks, instrumentation low-pass filters in data acquisition systems, and ultrasonic transducer front-end filtering in medical imaging. The wide dynamic range makes the LTC1067IGN particularly attractive when the upstream signal already spans most of the supply range. When designing with this part, plan clock-to-cutoff ratio carefully: the cutoff frequency equals fCLK/100 (or /50 for the -50 variant). A stable, low-jitter clock is essential - phase noise on the clock translates directly into passband distortion. Keep clock traces short and away from analog signal traces to prevent coupling. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet's typical application circuits.

Devis Contact
LTC1094CJ - 8-Ch 10-Bit Serial DAS | Analog Devices
LTC1094CJ

LTC1094CJ - 8-Ch 10-Bit Serial DAS | Analog Devices

Analog Devices LTC1094CJ is an 8-channel, 10-bit serial I/O data acquisition system in a 20-pin CERDIP package. The device combines a 10-bit switched-capacitor successive-approximation ADC core with software-configurable analog multiplexing, allowing a microcontroller or other serial host to acquire multiple analog channels through a compact mixed-signal interface. Its industrial temperature grade and through-hole construction suit instrumentation and embedded control systems where reliable PCB assembly and broad operating-temperature performance are important. A data acquisition system, or DAS, is an integrated mixed-signal semiconductor that combines analog multiplexing, conversion, and a digital control or serial interface. In the hierarchy of electronic components, the LTC1094CJ belongs to the ADC family, which forms part of the broader data-converter and signal-processing category. The 10-bit ADC provides 1,024 representable digital codes, making it appropriate for monitoring applications that require moderate measurement resolution rather than high-precision laboratory conversion. The key features of the LTC1094CJ include eight multiplexed input channels, 10-bit conversion resolution, serial I/O, and a selectable bipolar or unipolar input configuration. The switched-capacitor successive-approximation core allows the converter to combine compact implementation with practical acquisition performance. Because the multiplexer is software-configurable, a host controller can select among the available analog inputs and configure operating modes through the serial control interface. The LTC1094 family also includes 1-, 2-, 6-, and 8-channel configurations, while the LTC1094CJ specifically provides the 8-channel option. This distinction matters when comparing the CJ suffix with other family members. The CJ version is identified as an industrial-grade, 20-terminal, through-hole ceramic DIP rather than a surface-mount package. Its 20-CERDIP format supports conventional through-hole PCB assembly and is suitable for designs that favor robust mechanical attachment over compact board area. Typical uses include industrial process monitoring, transducer signal acquisition, laboratory measurement interfaces, environmental sensing, and embedded data-logging systems. In a multi-sensor installation, the eight-channel multiplexer can reduce the number of physical analog input connections needed by a microcontroller while retaining a common serial command and data path. The host system determines the channel sequence, acquisition timing, and interpretation of the resulting 10-bit values. A key design consideration is the analog front-end. Sensor outputs must remain within the selected bipolar or unipolar input range, and the source impedance seen by each muxed input can affect conversion accuracy and settling time. Layout should minimize trace lengths between sensors, protection components, and the LTC1094CJ while separating digital serial activity from sensitive analog nodes. Grounding, reference decoupling, and acquisition timing should be evaluated together rather than optimized independently. This product page combines the manufacturer product information, distributor identification, package details, and cross-reference findings into an engineering-focused description. It also identifies the verified drop-in alternative, documents replacement and selection questions, and highlights practical considerations for implementing an eight-channel serial data acquisition front end.

Devis Contact
LTC1099CN#30369 - 8-Bit 2.5µs ADC w/ S/H | Analog Devices | DIP-20
LTC1099CN#30369

LTC1099CN#30369 - 8-Bit 2.5µs ADC w/ S/H | Analog Devices | DIP-20

The Analog Devices LTC1099CN#30369 is an 8-bit, 2.5 µs analog-to-digital converter (ADC) with an integrated sample-and-hold amplifier, housed in a 20-pin PDIP (N-20) through-hole package. It offers one input channel with a flash-style conversion architecture, supports full Nyquist-rate sampling, and is qualified for the commercial 0 °C to 70 °C operating range. The part is supplied in a 20-PDIP package with an input count of 1 and a flash converter topology per the manufacturer's product family specification. What is a flash ADC? A flash ADC is a parallel architecture where every possible quantization level is realized by a dedicated comparator bank feeding an encoder; conversion happens in a single step so latency is essentially one comparator delay, making flash ADCs the fastest ADC topology but resolution-limited by comparator count. Within the converter hierarchy, the LTC1099 sits between SAR (successive approximation) and full flash converters, using a sub-ranging / flash-front-end plus internal sample-and-hold to digitize high-bandwidth analog signals up to the full Nyquist rate. As a data-conversion IC, it belongs to the broader category of data acquisition > analog-to-digital converter > monolithic 8-bit ADC. Key features include a 2.5 µs typical conversion time (corresponding to 156 kHz 5V p-p input bandwidth), a built-in track-and-hold, microprocessor-compatible interface for direct connection to parallel-bus microcontrollers, single +5 V supply operation, and a flash-derived architecture. The integrated S/H allows the converter to handle fast-step inputs without requiring an external buffer, simplifying front-end design. The LTC1099 uses a sub-ranging flash architecture with internal reference generation and digital error correction. The integrated sample-and-hold sits at the analog front end and guarantees accurate acquisition of fast transient signals at the full Nyquist rate, which a discrete ADC + external amplifier combination often cannot match for input slew without careful layout. Typical applications include waveform digitizers, digital oscilloscope front-ends, video bandwidth digitizing up to 156 kHz, data-acquisition boards for industrial instrumentation, and process-control signal conditioning. It also serves in VCO/PLL feedback readback, ultrasound return-signal sampling, and any design requiring fast 8-bit throughput in a simple parallel microprocessor interface. When designing with the LTC1099, ensure clean analog and digital grounds (separated at the device pin) and place the supply bypass capacitor as close as possible to the VCC pin. The internal S/H drives input capacitance; source-impedance and bandwidth trade-offs should be evaluated when feeding the analog input directly from a sensor or filter. This page synthesizes distributor pricing, drop-in equivalents, and design notes not present in the bare manufacturer datasheet, including intent-specific FAQs and a comparison table for engineers migrating from earlier 8-bit ADCs.

Devis Contact
LTC1283CJ - 10-Bit 8-Channel ADC | Analog Devices
LTC1283CJ

LTC1283CJ - 10-Bit 8-Channel ADC | Analog Devices

Analog Devices LTC1283CJ is a 3 V data acquisition IC containing a serial-interface, successive-approximation analog-to-digital converter with 10-bit unipolar or 9-bit-plus-sign bipolar resolution and an 8-channel input multiplexer. The device is offered in a ceramic 20-pin DIP package and is specified for the commercial temperature range. A data acquisition system converts real-world analog voltages into digital values for measurement, control, or display. Within the ADC category, the LTC1283 integrates a successive-approximation converter, an analog input multiplexer, and an on-chip sample-and-hold circuit. Its serial interface reduces the number of signal connections required between the converter and a controller while preserving dedicated analog measurement capability. Key features include an 8-channel analog multiplexer that can be configured for single-ended inputs, differential inputs, or combinations of both. The converter supports 10-bit unipolar and 9-bit plus sign bipolar operating modes. LTCMOS switched-capacitor technology performs the conversion, while the integrated sample-and-hold circuit captures the input voltage before conversion. A 3 V supply and a 20-pin ceramic DIP package support compact through-hole instrumentation layouts. The multiplexer is the central architectural feature for multi-sensor systems. Instead of dedicating one converter to every input, it routes selected channels to the shared converter and sample-and-hold circuit. Differential operation can reduce the influence of common-mode voltage on measurements, while single-ended operation simplifies connections for sensors with one signal output and a shared reference. Serial output supports economical connection to a microcontroller or embedded controller. Typical uses include industrial process measurement, multichannel sensor acquisition, battery-powered instrumentation, and embedded control systems that need several analog inputs but only moderate conversion resolution. The LTC1283CJ is also appropriate for prototypes and legacy equipment requiring a through-hole ceramic DIP footprint, especially where board area is less important than straightforward assembly and serviceability. Design around the exact input ranges, acquisition timing, reference requirements, and serial protocol listed in the Analog Devices LTC1283 datasheet. Confirm signal source impedance, acquisition time, reference stability, grounding, and digital-interface levels before finalizing the analog front end. Use the manufacturer's pin-description table and application guidance when assigning tracks and guarding inputs. This page organizes the LTC1283CJ's converter architecture, multiplexing capabilities, package details, sourcing path, and engineering considerations into a practical selection reference. It also separates verified device facts from replacement and lifecycle decisions that require direct manufacturer confirmation.

Devis Contact
LTC1380IGN#PBF - 8-Ch SMBus Analog Mux, 70Ohm | Analog Devices
LTC1380IGN#PBF

LTC1380IGN#PBF - 8-Ch SMBus Analog Mux, 70Ohm | Analog Devices

The Analog Devices LTC1380IGN#PBF is a CMOS single-ended 8-channel analog multiplexer with an SMBus-compatible two-wire digital interface, featuring 70 ohm on-resistance, 10 uA supply current, and a wide 2.7 V to +/-5 V supply range, housed in a 16-pin SSOP (SSOP-16) package. An analog multiplexer (mux) is a switching IC that selects one of several analog input signals and routes it to a single output under digital control, making it a foundational block in the signal-switching hierarchy: multiplexer switch IC -> analog switch -> data conversion front end -> signal chain. Unlike electromechanical relays, CMOS muxes such as the LTC1380 switch in microseconds, consume microamp-level power, and integrate the decode logic on-chip. Key differentiating features include the SMBus-compatible serial interface that requires only two wires (SCL and SDA), four hard-wired SMBus addresses selectable with two external address pins, and the Pb-free (RoHS) SSOP-16 package indicated by the #PBF suffix. The extremely low 10 uA supply current makes the part well suited to battery-powered and remotely powered data-acquisition systems. Architecturally, the LTC1380 uses CMOS transmission-gate switches driven by an on-chip decode stage controlled by the serial port. Break-before-make switching prevents momentary shorting of selected channels, and the 70 ohm on-resistance keeps insertion loss low in moderate-impedance signal paths. The wide 2.7 V to +/-5 V supply capability supports both single-supply 3 V/5 V logic systems and dual-supply analog domains for bipolar signals. Typical applications include industrial data-acquisition front ends, battery-powered sensor monitoring, automatic test equipment channel routing, and general-purpose analog signal selection in embedded systems with an SMBus or I2C-compatible controller. Design-wise, keep the off-channels' source impedance low and add an op-amp buffer after the mux output if the downstream load is capacitive or high-value, because the 70 ohm RON combines with load current to create gain error. This page synthesizes distributor pricing context, drop-in alternatives, pin/package guidance, and practical design notes not found in the manufacturer datasheet.

Devis Contact
LTC1409IG - 12-Bit 800ksps Sampling ADC | Analog Devices
LTC1409IG

LTC1409IG - 12-Bit 800ksps Sampling ADC | Analog Devices

Analog Devices LTC1409IG is a 12-bit, 800 ksps sampling analog-to-digital converter with a parallel interface in a 28-pin SSOP package. It supports true differential input, provides a 1 µs conversion time, and operates from ±5 V supplies while dissipating 80 mW. The converter is intended for precision signal acquisition, industrial control, instrumentation, communications, and data-processing systems requiring deterministic sampling without pipeline delay. A sampling ADC is a data-converter category that samples an analog input at a specified instant and converts it into a digital code. The LTC1409IG belongs to the successive-approximation-register family, where a sample-and-hold circuit captures the input before an internal 12-bit conversion completes. It includes a high-dynamic-range sample-and-hold stage and a precision internal reference, while also accepting an external reference when greater system-level control is required. Key characteristics include an 800 ksps maximum sampling rate, a 1 µs conversion time, and a ±2.5 V full-scale differential input range. The converter provides single-ended or differential signal handling, digital shutdown control, and selectable operating modes. Its specified maximum DC linearity and differential nonlinearity are ±1 LSB, while signal-chain performance reaches 72.5 dB SINAD and 86 dB THD at the Nyquist frequency. The architecture supports both internal and external reference operation. The internal reference has a stated temperature coefficient of 15 ppm/°C, providing a compact solution when a dedicated external reference would add cost or board area. Shutdown options include Nap, which reduces power dissipation to 4 mW, and Sleep, which reduces it to 10 µW, making the converter suitable for intermittently sampled acquisition systems. Typical applications include process-control loops, multichannel measurement systems, communications receivers, industrial instrumentation, waveform capture, and precision sensor acquisition. Its parallel data bus allows the converted word to be read directly by a microcontroller, DSP, FPGA, or other digital controller, making bus timing and signal-integrity layout important considerations. When designing a board around the LTC1409IG, preserve the specified dual-supply range and ensure adequate input settling before each conversion. Place input and reference components close to their associated pins, maintain short parallel-bus routes, and provide suitable decoupling. Confirm that the selected downstream logic voltage and acquisition timing support the converter's parallel interface and sampling requirements. This page combines manufacturer specifications, package information, verified source links, drop-in family references, and practical design guidance to support component selection, schematic planning, PCB layout, and replacement evaluation.

Devis Contact
LTC1416CG - 14-Bit 400ksps Low-Power ADC | Analog Devices
LTC1416CG

LTC1416CG - 14-Bit 400ksps Low-Power ADC | Analog Devices

Analog Devices LTC1416CG is a low-power, 14-bit, successive-approximation sampling ADC with a conversion time of 2.2 microseconds, a maximum sampling rate of 400 ksps, and a 28-pin SSOP package. The converter accepts a bipolar full-scale input range of ±2.5 V and operates from ±5 V supplies while drawing 70 mW. A sampling ADC is a data-converter category that uses a sample-and-hold circuit and successive-approximation conversion to translate an analog voltage into a digital code. The LTC1416 belongs to the ADC, data-converter, signal-processing, and semiconductor hierarchy. Its high dynamic-range sample-and-hold front end makes it suitable for precision instrumentation, industrial measurement, data acquisition, and control systems that require accurate conversion without a high-power switching architecture. The principal characteristics are 14-bit resolution, 400 ksps throughput, and 2.2 microsecond conversion time. The Analog Devices datasheet also identifies ±2 LSB maximum integral nonlinearity, ±1.5 LSB maximum differential nonlinearity, and operation from ±5 V supplies. Two digitally selectable shutdown modes help reduce power consumption when conversion activity is intermittent. The converter supports internal or external reference operation and includes a precision reference according to the manufacturer product information. The parallel-output architecture supports direct connection to digital control logic when the converter is mounted close to the processor or FPGA. A SAR ADC is useful when deterministic latency, moderate resolution, and modest conversion rates matter more than very high throughput. This combination of 14-bit resolution, 400 ksps sampling, selectable shutdown modes, and bipolar input range allows the LTC1416 to balance measurement resolution, throughput, power use, and implementation complexity. Typical uses include process-control loops, analog sensor acquisition, laboratory measurement instruments, industrial data-logging equipment, and embedded systems that sample slowly varying or moderately changing analog signals. The internal reference can simplify designs where an external precision reference would add cost and board area, while external-reference operation offers a path for shared references or calibration schemes. When laying out the circuit, place input, reference, and bypass connections to minimize pickup around the high-impedance analog input. Use the manufacturer pin-description table when assigning signals and observe the specified acquisition, conversion, and shutdown timing. Check the power-supply requirements and reference selection carefully because incorrect sequencing or bypassing can degrade accuracy even when the nominal sampling rate is suitable. This product overview consolidates the converter's resolution, throughput, input range, power characteristics, shutdown options, and package details into an engineering-oriented selection reference. It also distinguishes verified pin-compatible family alternatives from broader functional ADC choices, helping designers evaluate PCB reuse, interface compatibility, and measurement requirements before committing to a layout.

Devis Contact
LTC1418CN#PBF - 14-bit 200ksps Low Power SAR ADC | Analog Devices
LTC1418CN#PBF

LTC1418CN#PBF - 14-bit 200ksps Low Power SAR ADC | Analog Devices

The Analog Devices LTC1418CN#PBF (originally Linear Technology) is a low power, 200 ksps, 14-bit successive-approximation analog-to-digital converter (SAR ADC) offered in a 28-pin PDIP through-hole package. Key headline parameters include a 200 ksps sampling rate, 14-bit resolution, 15 mW typical power dissipation from a single 5 V or ±5 V supply, and selectable 14-bit parallel or serial data output format. The on-board high-performance sample-and-hold, precision reference, and internal timing keep external component count to a minimum, which simplifies board layout and reduces BOM cost. What is a SAR ADC? A successive-approximation analog-to-digital converter is a type of ADC that performs a binary search across an internal DAC to converge on the input voltage one bit per cycle. Within the broader hierarchy, this places SAR ADCs alongside pipelined, sigma-delta, and flash converters inside the data acquisition IC family. SAR converters deliver an excellent balance of speed, accuracy, and low power, which is why they remain a workhorse for industrial process control, instrumentation, and multiplexed data-acquisition front ends. Key features of the LTC1418CN#PBF include a built-in track-and-hold amplifier that eliminates the need for an external SHA, a typical differential non-linearity (DNL) of ±0.5 LSB, and bipolar/unipolar input capability when operated from ±5 V. Power-down mode reduces dissipation for battery-powered applications, and the wide analog input range (0 V to 5 V single-ended, ±5 V true bipolar) gives designers flexibility when digitizing transducer or sensor signals. Architecturally, the LTC1418 uses a charge-redistribution DAC array combined with a precision buried-Zener reference and auto-calibrated switch-capacitor front end. At 200 ksps, it sustains full 14-bit performance without missing codes, and the serial/parallel interface allows the same silicon to drop into either high-pin-count microcontroller buses or low-pin-count SPI controllers. Typical applications include industrial process-control data acquisition boards, portable or battery-powered instrumentation, multiplexed sensor read-back, and digital signal processing front ends. The 5 V single-supply capability also makes it suitable for legacy 5 V-only embedded designs. Designers should note that the LTC1418 is in the process of being discontinued; an SSOP-28 replacement (LTC1418CG#PBF) exists but is NOT pin-to-pin compatible with the DIP-28. Plan PCB rework or substitute silicon if the DIP-28 supply runs out. This page synthesizes Analog Devices datasheet data, distributor stock and pricing from DigiKey, and practical design considerations not found on manufacturer product pages.

Devis Contact
LTC1605-1CN#PBF - 16-Bit, 100ksps SAR ADC, 0-4V Input, 28-PDIP | Analog Devices
LTC1605-1CN#PBF

LTC1605-1CN#PBF - 16-Bit, 100ksps SAR ADC, 0-4V Input, 28-PDIP | Analog Devices

The Analog Devices LTC1605-1CN#PBF is a 16-bit, 100ksps successive-approximation analog-to-digital converter that operates from a single 5V supply, drawing only 55mW (typical) and housed in a 28-pin PDIP through-hole package. It integrates a sample-and-hold amplifier, a precision internal reference, a switched-capacitor 16-bit SAR ADC core, and a trimmed internal clock, providing a complete data-acquisition solution in a single IC. A successive-approximation register (SAR) ADC is a type of analog-to-digital converter that performs a binary search across the input voltage using an internal DAC and comparator; SAR ADCs are valued for low latency, deterministic conversion time, and excellent DC accuracy with no pipeline delay, making them well-suited for multiplexed data acquisition, industrial process control, and precision instrumentation where a single-channel, low-noise conversion is required. Key features include a 0V to 4V true-differential analog input range (industry-standard unipolar), ±2.0 LSB maximum integral nonlinearity (INL), guaranteed 16-bit no-missing-codes over temperature, and a flexible parallel data output interface (16-bit wide or two-byte) that connects directly to microprocessors, DSPs, and FIFOs. The internal 2.5V reference is trimmed for low drift; an external reference may be applied for higher absolute accuracy over temperature. A CONVST input and BUSY (EOC) output simplify handshaking with external logic. Architecturally, the device uses a charge-redistribution switched-capacitor DAC paired with a low-noise comparator and an SAR control engine; the input sample-and-hold acquires the signal on the rising edge of CONVST and the conversion completes in 8µs, after which data is presented on the parallel port with BUSY going low. Single 5V operation eliminates the negative supply required by many legacy bipolar ADCs, simplifying board power design. Typical applications include industrial process control and multi-channel data-acquisition front ends (paired with an external MUX), precision weighing scales and load-cell digitizers, bench-top and laboratory instrumentation, medical diagnostic equipment, and high-accuracy temperature or strain-gauge measurement systems. The LTC1605-1CN#PBF's commercial 0°C to 70°C operating range suits laboratory, factory-floor, and bench environments. When designing with this part, place 10µF (or larger) bypass capacitors close to the AVdd and DVdd pins and respect a star-ground topology between the analog input ground return and digital ground to avoid code-dependent noise coupling into the reference. The 28-PDIP package is convenient for prototype boards, sockets, and through-hole assembly but is not recommended for new high-density surface-mount designs - consider the SSOP-28 (LTC1605-1CG#PBF) for SMT layouts. This page synthesizes distributor pricing, true drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
LTC1605-1IN#PBF - 16-Bit 100ksps SAR ADC | Analog Devices
LTC1605-1IN#PBF

LTC1605-1IN#PBF - 16-Bit 100ksps SAR ADC | Analog Devices

The Analog Devices LTC1605-1IN#PBF is a 16-bit, 100 ksps successive-approximation analog-to-digital converter (SAR ADC) in a 28-pin PDIP (N) through-hole package. According to the Analog Devices datasheet, the device draws only 55 mW (typical) from a single 5 V supply, includes a sample-and-hold front-end, a precision internal reference, and a trimmed internal clock, providing a complete 16-bit data-acquisition solution in one IC. The unipolar input range is 0 V to 4 V (LTC1605-1 variant; LTC1605-2 variant covers ±4 V bipolar). The converter features a microprocessor-compatible 16-bit or two-byte parallel output port for direct connection to data buses and DSP/microcontroller interfaces. A SAR ADC is a successive-approximation-register analog-to-digital converter that uses a binary-search algorithm and an internal capacitive DAC to resolve the input voltage one bit at a time per clock cycle. SAR ADCs occupy the middle ground between delta-sigma (high resolution, low speed) and flash (very high speed, low resolution) architectures. They are the dominant choice for 12-16 bit industrial data-acquisition systems running at 10 ksps to 1 Msps, particularly when deterministic latency and a parallel/serial output are required. The LTC1605-1IN#PBF inherits the lineage of the industry-standard LTC1605 family, all of which share the same 28-pin pinout and timing characteristics for drop-in upgrades. Key features include 16-bit no-missing-codes performance, 86 dB typical signal-to-noise ratio, a 100 ksps sampling rate, and an external reference option for systems that require better temperature drift than the internal 2.5 V reference provides. The 28-pin PDIP package is through-hole, simplifying prototyping and field replacement for industrial instrumentation. Typical applications include industrial process control, multi-channel data-acquisition boards, weigh-scale and load-cell digitizers, panel meters, instrumentation front-ends, and bench-top test-and-measurement equipment. The 5 V single-supply operation and parallel data port allow direct connection to legacy parallel-signal processors and modern microcontrollers/DSPs without additional level translation. When designing with the LTC1605-1IN#PBF, ensure the analog input is buffered if the source impedance exceeds the datasheet-specified value, and decouple VDD with a 10 µF tantalum in parallel with a 0.1 µF ceramic placed within 1 cm of the supply pin. The #PBF suffix indicates lead-free (Pb-free) and RoHS-compliant construction, qualifying the part for modern and export-controlled designs.

Devis Contact
LTC1605-2CN#PBF - 16-Bit 100ksps ±4V Bipolar SAR ADC | ADI
LTC1605-2CN#PBF

LTC1605-2CN#PBF - 16-Bit 100ksps ±4V Bipolar SAR ADC | ADI

The Analog Devices LTC1605-2CN#PBF is a 16-bit, 100 ksps successive-approximation analog-to-digital converter that operates from a single 5 V supply and dissipates only 55 mW typical. Housed in a 28-pin PDIP through-hole package, the device integrates a sample-and-hold front end, a precision internal reference, a switched-capacitor SAR core, and a trimmed internal clock, enabling a complete 16-bit conversion solution in one IC. The -2 suffix denotes a bipolar ±4 V analog input range, which makes the part well suited to industrial signal acquisition that uses a true bipolar front end. A successive-approximation register (SAR) ADC is a type of data converter that performs one binary bit decision per conversion cycle, using an internal comparator, DAC, and successive-approximation logic. SAR converters sit in the broader ADC hierarchy between delta-sigma (high resolution, low speed) and flash (high speed, low resolution), and are favored for multiplexed data-acquisition systems because they perform a complete, deterministic conversion in N clock cycles with no pipeline latency. The LTC1605-2 exemplifies this architecture with its single-shot, software-controlled conversion cycle. Key specifications of the LTC1605-2 include 16-bit resolution with no missing codes, ±4 V bipolar input range, 100 ksps sampling rate, parallel data interface, ±2.5 LSB INL typical, and integrated reference. The internal clock and the integrated reference eliminate external ADC support components, simplifying the analog front end. Because the part is single-supply 5 V with a true bipolar differential input stage, designers can connect the output of a ±4 V instrumentation amplifier directly to the ADC inputs with minimal signal conditioning. The architecture uses a charge-redistribution switched-capacitor DAC inside the SAR loop, a technique that yields excellent DC linearity for instrumentation workloads. The integrated 4.096 V reference is trimmed at the factory, so the converter achieves specified noise and INL performance without external reference components, although a 2.2 µF bypass close to the REF pin is required for full accuracy. Typical applications include process-control analog input modules, industrial PLC analog front ends, precision data-acquisition boards, multichannel instrumentation front ends with bipolar signals, and laboratory instrumentation that requires 16-bit accuracy without high-speed throughput. Designers in these segments value the deterministic conversion latency and the simple parallel read interface. When designing the PCB, place the 2.2 µF REF bypass capacitor and the 10 µF VCC decoupling capacitor as close to the IC pins as possible. Use a ground plane under the analog section and keep digital return currents out of the analog ground path. Use the S/H (sample-and-hold) pin or the CS and RD signals to start conversions; the LTC1605-2 does not auto-run. This page synthesizes distributor pricing, pin-compatible ADI alternatives in the same 28-PDIP footprint, and practical layout notes beyond the manufacturer datasheet, helping engineers evaluate LTC1605-2CN#PBF for drop-in upgrades, second sources, and bipolar-input acquisition channels.

Devis Contact
LTC1605ACN - 16-Bit 100ksps ADC with Bipolar ±10V Input | Analog Devices
LTC1605ACN

LTC1605ACN - 16-Bit 100ksps ADC with Bipolar ±10V Input | Analog Devices

The Analog Devices LTC1605ACN is a 16-bit, 100 ksps sampling analog-to-digital converter (ADC) housed in a 28-pin PDIP through-hole package. It draws only 55 mW (typical) from a single +5 V supply, accepts a bipolar ±10 V input range, and features an internal precision reference with trimmed internal clock for easy standalone operation. An analog-to-digital converter (ADC) is a data-converter integrated circuit that converts a continuous analog voltage into a discrete digital code, occupying a key position in the signal-chain hierarchy: transducer -> analog front end / signal conditioning -> ADC -> digital processor. Successive-approximation register (SAR) ADCs in particular combine a sample-and-hold, precision reference, switched-capacitor DAC and SAR logic to deliver one conversion per clock, with low latency and deterministic behavior well suited to multiplexed data acquisition and industrial instrumentation. Key features of the LTC1605ACN include ±2.0 LSB (max) INL over temperature, guaranteed 16-bit no missing codes, a microprocessor-compatible 16-bit or two-byte parallel output port, and the ability to be driven by an external reference when higher absolute accuracy is required across temperature. Synchronous sampling and a wide input range let it directly digitize industrial ±10 V signals without external scaling amplifiers. The device uses a precision bandgap reference and trimmed internal clock, simplifying the analog front end to a simple RC input network plus an external reference option for temperature-stable accuracy. Successive-approximation architecture yields deterministic latency and excellent DC linearity for instrumentation applications. Typical applications include industrial process control data acquisition boards, multichannel multiplexed data loggers, instrumentation and measurement front ends, and legacy factory automation I/O subsystems. The bipolar ±10 V range lets it connect directly to legacy industrial sensors and 4-20 mA loop resistors. Design with the device by ensuring the analog input pin sees a low-impedance buffer or RC network matching the ADC's switched-capacitor front end, and by tying REFCOMP to a 10 µF bypass capacitor near the pin to minimize reference noise. Latency is one conversion clock, simplifying timing analysis for sequential multiplexer scans.

Devis Contact
LTC1605AIN - 16-Bit 100ksps Sampling ADC ±10V | Analog Devices
LTC1605AIN

LTC1605AIN - 16-Bit 100ksps Sampling ADC ±10V | Analog Devices

The Analog Devices LTC1605AIN is a 16-bit, 100ksps sampling analog-to-digital converter that draws only 55 mW (typical) from a single 5V supply, packaged in a 28-pin SSOP. It integrates a sample-and-hold amplifier, a precision internal reference, a switched-capacitor successive-approximation ADC core, and a trimmed internal clock, providing a complete bipolar-input ADC solution. The bipolar analog input range is ±10V, suitable for industrial process control, instrumentation, and signal-isolation data-acquisition front-ends. An ADC (analog-to-digital converter) is a semiconductor device that converts a continuous analog voltage or current into a discrete digital code; sampling ADCs additionally include a sample-and-hold front-end that captures and freezes the input at a precise moment so that the conversion can proceed without aliasing. In the broader component hierarchy, the LTC1605AIN is a successive-approximation-register (SAR) ADC, a sub-category of data converters that sits under interface/ADC ICs in mixed-signal systems. SAR ADCs are favored for their deterministic latency, low power consumption, and excellent DC accuracy compared with delta-sigma or pipeline architectures, making them ideal for multiplexed data-acquisition systems. Key features include ±2.0 LSB maximum integral nonlinearity, guaranteed no missing codes at 16 bits, ±10V true bipolar input range from a single 5V supply, and a 55 mW typical power dissipation. The part is specified over the commercial 0°C to 70°C operating range, with the 'N' suffix indicating an SSOP-28 package and 'I' indicating the commercial temperature grade. The internal reference and trimmed clock eliminate the need for external components, simplifying board layout and reducing BOM cost. Architecturally, the LTC1605AIN combines a fast bipolar-input track-and-hold with a charge-redistribution SAR core and an on-chip reference. The trimmed internal clock removes the requirement for an external timing source, and the parallel output interface delivers conversion results in a single read cycle. The 100ksps throughput makes it well suited to multiplexed multi-channel systems where each channel can still be sampled at several kHz. Typical applications include industrial process control and instrumentation, multiplexed data-acquisition systems, signal-isolation front-ends, and portable or battery-powered test equipment. The ±10V bipolar input makes it a natural drop-in for legacy 5V-only signal chains migrating from older bipolar ADC designs. When designing with this part, allocate adequate board area for the analog input anti-alias filter and bypass the supply pin with a 10 µF tantalum plus 0.1 µF ceramic capacitor within 10 mm of the device. The analog and digital grounds should be tied at a single star point beneath the IC to minimize noise coupling from the parallel output bus into the sensitive input front-end. This page synthesizes distributor pricing, drop-in same-package alternatives drawn from the Site MPN list, and practical design notes not found in the manufacturer datasheet, enabling faster BOM selection for engineers maintaining or designing-in the LTC1605AIN.

Devis Contact
LTC1605CN#PBF - 16-Bit 100ksps SAR ADC, ±10V Bipolar | ADI
LTC1605CN#PBF

LTC1605CN#PBF - 16-Bit 100ksps SAR ADC, ±10V Bipolar | ADI

The Analog Devices (formerly Linear Technology) LTC1605CN#PBF is a 100 ksps, 16-bit sampling analog-to-digital converter (ADC) that draws only 55 mW (typical) from a single 5 V supply, housed in a 28-pin PDIP (through-hole) package. The device integrates a sample-and-hold front end, a precision buried-zener reference, a switched-capacitor successive-approximation ADC core, and a trimmed internal clock, providing a complete data-acquisition front end in one IC. A successive-approximation register (SAR) ADC is a precision converter architecture that performs a binary search across an internal DAC for each conversion, achieving deterministic low-latency (one conversion cycle) results with no pipeline delay. SAR ADCs are widely used in industrial, instrumentation, and process-control applications where DC accuracy, high linearity, and excellent AC performance at moderate sampling rates are required. The LTC1605 sits in the precision SAR family alongside the 14-bit LTC1410 and 12-bit LTC1290, sharing a common analog front-end philosophy and pinout philosophy. Key specifications include 16-bit resolution with no missing codes, ±2.0 LSB maximum integral nonlinearity (INL), ±10 V true-bipolar input range from a single 5 V supply, 100 ksps sampling rate, and 55 mW typical power dissipation. The integrated reference eliminates external reference components, simplifying the bill of materials. The parallel data interface allows direct connection to microprocessors, FPGAs, or DSPs without serial-deserialization glue logic. Typical applications include industrial process control, multiplexed data-acquisition systems, precision instrumentation, seismic and weigh-scale digitizers, spectrum and vibration analysis front ends, and bench-top DMM front ends. The ±10 V true-bipolar input is a key differentiator, allowing direct digitization of industrial sensor outputs (4-20 mA loops scaled to voltage, strain-gauge bridges, thermocouple amplifiers) without external signal conditioning. When designing with the LTC1605, allocate at least 8 analog input pins plus dedicated AGND and DGND pins, and follow ADI's recommended four-layer board with separate analog and digital ground planes joined at a single point near the IC. The internal reference requires a 10 µF bypass capacitor on the REFCOMP pin for optimal linearity. This page synthesizes distributor pricing, drop-in 28-PDIP alternatives (LTC1605IN, LTC1605-1CN, LTC1605-2CN), and practical design notes not aggregated on any single manufacturer or distributor page.

Devis Contact
LTC1650AIN#PBF - 16-Bit Low-Glitch Voltage Output DAC | ADI
LTC1650AIN#PBF

LTC1650AIN#PBF - 16-Bit Low-Glitch Voltage Output DAC | ADI

The Analog Devices LTC1650AIN#PBF is a 16-bit, low-glitch, rail-to-rail voltage-output digital-to-analog converter (DAC) housed in a 16-pin PDIP through-hole package, qualified to the industrial -40C to +85C temperature range. It integrates a precision R-2R ladder, an output buffer amplifier, and a three-wire cascadable serial (SPI/MICROWIRE-compatible) interface, delivering 16-bit monotonic performance over temperature with a glitch impulse of just 2 nV-s. The DAC operates from dual plus/minus 5 V supplies and dissipates approximately 50 mW, with the output swing defined by REFLO and REFHI reference inputs that can be tied for unipolar or bipolar modes. A digital-to-analog converter (DAC) is a data-conversion integrated circuit that translates a digital code word into a precisely scaled analog voltage or current. Within the broader data-converter family (ADC and DAC), this part belongs to the precision narrow-DC voltage-output DAC category, sitting under the hierarchy: DAC -> data converter -> mixed-signal IC -> semiconductor. The LTC1650AIN#PBF specifically targets low-glitch, low-noise, buffered voltage-output applications where a clean step transition and rail-to-rail swing are critical. Key differentiating specifications include 2 nV-s glitch impulse, 30 nV/sqrt(Hz) noise spectral density, 16-bit guaranteed monotonicity, and a true rail-to-rail output buffer that swings to within millivolts of either supply rail. The cascadable three-wire serial interface allows multiple LTC1650 devices to share a single SPI bus by daisy-chaining the DOUT pin into the next device's DIN pin, simplifying multi-axis or multi-channel designs. Architecturally, the device combines a thin-film R-2R ladder network for INL/DNL linearity with an on-chip output op-amp capable of driving 2 kohm/100 pF loads. The internal reference inputs (REFHI/REFLO) decouple the output range from the supply rails, enabling asymmetric spans such as 0 to 4.096 V for unipolar or plus/minus 4.096 V for bipolar operation. Typical applications include industrial process control calibration, automated test equipment (ATE) waveform generation, digitally controlled offset and gain trimming, programmable voltage references, and motor-control setpoint generation. The wide output swing and low glitch make the LTC1650AIN#PBF a strong fit where each code transition must not couple into downstream signal-chain stages. When designing with this part, place 0.1 uF decoupling capacitors close to AVDD, DVDD, and AVSS pins and route REFHI/REFLO traces as a differential pair. Keep the analog ground (AGND) and digital ground (DGND) joined at a single star point beneath the IC to preserve the 16-bit linearity. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical PCB-level design guidance not found in the manufacturer datasheet alone, giving engineers a single reference for evaluation and sourcing.

Devis Contact
LTC1657LIGN - 16-Bit Rail-to-Rail DAC, 28-SSOP | Analog Devices
LTC1657LIGN

LTC1657LIGN - 16-Bit Rail-to-Rail DAC, 28-SSOP | Analog Devices

The Analog Devices LTC1657LIGN is a 16-bit rail-to-rail micropower parallel digital-to-analog converter (DAC) housed in a 28-lead SSOP (GN) package. It operates from a single 2.7 V to 5.5 V supply, delivers monotonic 16-bit performance over the industrial temperature range, and provides a deglitched rail-to-rail voltage output stage that swings within 8 mV of either rail. Typical supply current is 650 uA, making it one of the lowest-power 16-bit parallel DACs in its class. A digital-to-analog converter (DAC) is an integrated circuit that converts a digital code word into a precisely defined analog voltage or current. Within the broader signal-chain taxonomy, the LTC1657 belongs to the precision converter family -> data converter -> mixed-signal IC -> semiconductor. The LTC1657 specifically targets low-power, high-resolution applications where a parallel microprocessor-style interface is preferred for fast code updates without serial-clock overhead. Key features include guaranteed 16-bit monotonicity over temperature, maximum DNL of ±1 LSB, internal power-on reset to zero scale, an asynchronous CLR pin for output forcing, and a built-in 1.25 V reference accessible at the REFOUT pin (LTC1657L variant). The device accepts a parallel 16-bit word and updates the output on the rising edge of CS/WR. Settling time to ±1 LSB is specified at 20 us for a full-scale step. The SSOP-28 footprint is industry-standard and compatible with the LTC1450 12-bit family, providing an upgrade path for existing designs. Architecturally, the LTC1657LIGN uses a resistor-string (R-2R ladder) topology with an output buffer amplifier, ensuring inherently monotonic operation and low glitch impulse. The reference input can be driven externally or tied to the internal 1.25 V bandgap via REFOUT, providing design flexibility for both ratiometric and absolute-output applications. Typical applications include industrial process control, digital offset and gain adjustment, automatic test equipment (ATE) programmable stimulus, audio attenuators with parallel volume control, and portable battery-powered instrumentation where the 650 uA quiescent current extends operating life. The wide supply range and rail-to-rail output maximize signal swing on low-voltage rails. When designing with this device, ensure the REFLO pin is tied to GND and that bypass capacitors of 0.1 uF and 10 uF are placed close to VCC. The asynchronous CLR pin must be held high during normal operation to avoid unintended reset events. Designers migrating from the LTC1450 12-bit family benefit from pin-compatibility and only need to extend the data bus from 12 to 16 bits. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single source for evaluation, sourcing, and PCB layout reuse.

Devis Contact
LTC1740CG - 14-Bit 6Msps Sampling ADC | Analog Devices
LTC1740CG

LTC1740CG - 14-Bit 6Msps Sampling ADC | Analog Devices

The Analog Devices LTC1740CG is a 14-bit, 6Msps sampling analog-to-digital converter with one pipelined input, a parallel interface, and a 36-SSOP package. It operates from a single 5V supply or dual ±5V supplies and consumes 245mW, making it suitable for compact data-acquisition and signal-processing systems. The converter supports differential full-scale input ranges of ±2.5V and ±1.25V with its internal precision reference. A sampling ADC is a mixed-signal integrated circuit that samples an analog voltage and converts it into a digital code. The LTC1740CG belongs to the ADC and DAC hierarchy, combining an input sample-and-hold circuit, a 14-bit conversion stage, a programmable reference, and a parallel digital interface in one device. This integration reduces external component count and simplifies the connection between analog inputs and digital processors or programmable logic. The device converts at 6Msps while providing 79dB signal-to-noise plus distortion ratio and 91dB spurious-free dynamic range at a 2.5MHz input frequency. Its differential nonlinearity is 0.5LSB, and its integral nonlinearity is less than 1LSB. The sampling system has an 80MHz full-power bandwidth, allowing designers to evaluate dynamic performance and antialiasing requirements across a broad input-frequency range. Power architecture is another important feature. A single 5V rail simplifies conventional positive-supply designs, while dual ±5V operation supports bipolar analog signal chains. The 245mW power consumption is suitable for portable and embedded instrumentation when paired with careful thermal and layout design. The flexible input circuit can also accept other full-scale ranges when an external reference is used. Typical applications include industrial process monitoring, medical instrumentation, communications receivers, automated test equipment, and digital oscilloscope or waveform-capture front ends. The parallel output allows direct connection to an FPGA, CPLD, DSP, or other high-speed digital acquisition logic. When laying out the circuit, place the input, reference, and decoupling connections close to the device and maintain a controlled return path for the analog input. Check the converter’s supply sequencing, output coding, clocking, and acquisition timing requirements in the manufacturer datasheet before connecting it to a capture system. This page combines the manufacturer specifications with practical application guidance for engineers evaluating the LTC1740CG.

Devis Contact