Produits (39 000+)

LTC6226IDC - 420MHz GBW Low Noise RRIO Op Amp | ADI
LTC6226IDC

LTC6226IDC - 420MHz GBW Low Noise RRIO Op Amp | ADI

The Analog Devices LTC6226IDC is a very fast, low-noise, rail-to-rail output, unity-gain stable single operational amplifier with a gain-bandwidth product of 420MHz and a slew rate of 180V/us, packaged in a 6-lead DFN (2mm x 2mm) with exposed pad. The input-referred voltage noise is just 1nV/sqrt(Hz) and harmonic distortion is below -90dBc for 4Vp-p signals at 1MHz. What is an op amp? An operational amplifier is a high-gain DC-coupled analog building block used in signal conditioning, filtering, and feedback loops. Rail-to-rail output (RRIO) op amps extend the output swing to within millivolts of either supply rail, maximizing dynamic range on low-voltage supplies. The LTC6226 belongs to the precision/high-speed amplifier sub-family, which sits between general-purpose op amps and fully-dedicated high-speed current-feedback amplifiers in the analog IC hierarchy. Key features of the LTC6226IDC include 420MHz gain-bandwidth product, 180V/us slew rate, 1nV/sqrt(Hz) input voltage noise density, less than -90dBc THD at 1MHz/4Vp-p, rail-to-rail output swing, and unity-gain stability. The part runs from a 2.8V to 11.75V total supply (or +/-1.4V to +/-5.875V dual) and draws approximately 5.5mA of quiescent current. The exposed-pad DFN-6 package keeps the thermal resistance low for continuous high-output-current operation. The internal architecture uses a complementary bipolar input stage followed by a rail-to-rail class-AB output stage. The very low input noise density makes the LTC6226IDC well suited for photodiode transimpedance amplifiers and ultrasound front-ends where the signal-to-noise ratio is dominated by the front-end amplifier's own voltage noise rather than its current noise. Typical applications for the LTC6226IDC include 16-bit to 20-bit ADC drivers, photodiode transimpedance amplifiers, ultrasound preamplifiers, active filters, video line drivers, and low-noise instrumentation front-ends. The combination of low noise, high GBW, and rail-to-rail output makes it a strong fit for single-supply industrial data-acquisition systems. When designing with this op amp, decouple the supply pins with a 0.1uF X7R ceramic capacitor placed as close as possible to the V+ and V- pins, plus a bulk 10uF tantalum or ceramic capacitor. The exposed pad must be soldered to a copper pour to keep junction temperature within datasheet limits at high output swing and high load current. This page consolidates distributor pricing, drop-in alternatives, and practical design notes that are not always easy to find in the manufacturer datasheet.

Devis Contact
LTC6226IS6#TRMPBF - 420MHz Low-Noise Rail-to-Rail Op-Amp | ADI
LTC6226IS6#TRMPBF

LTC6226IS6#TRMPBF - 420MHz Low-Noise Rail-to-Rail Op-Amp | ADI

The Analog Devices LTC6226IS6#TRMPBF is a very fast, low-noise, rail-to-rail output, unity-gain stable single operational amplifier housed in a 6-pin TSOT-23 (S6) package. It delivers a gain-bandwidth product of 420 MHz, a slew rate of 180 V/us, and an input-referred voltage noise of 1 nV/root-Hz, achieving distortion below -90 dBc for 4 Vp-p signals at 1 MHz. The device is specified for single or dual supply operation from 2.5 V to 11.75 V (or +/-1.25 V to +/-5.875 V). An operational amplifier (op-amp) is a high-gain DC-coupled analog building block used to amplify, buffer, filter, or condition voltage signals. Within the broader signal chain hierarchy, the LTC6226 belongs to the high-speed, low-noise precision amplifier category: op-amp -> high-speed amplifier -> precision amplifier -> analog IC -> integrated circuit -> semiconductor. Rail-to-rail output extends usable dynamic range to within millivolts of either supply rail, maximizing SNR in low-voltage systems. Key features include 1 nV/root-Hz input voltage noise density (industry-leading for a 420 MHz GBW device), 180 V/us slew rate for fast large-signal settling, 100 us startup time, and 1 mA typical supply current per amplifier. The TSOT-23-6 footprint enables dense PCB layouts while preserving the bandwidth needed for video, RF IF, and high-speed data-acquisition front ends. CMOS input bias current minimizes source-loading errors versus traditional bipolar parts. The architecture combines a low-noise input stage with a rail-to-rail output stage and internal compensation for unity-gain stability without external components. The wide supply range simplifies integration into 3.3 V, 5 V, +/-5 V, and +/-10 V analog rails, and the 180 V/us slew rate preserves signal integrity on fast pulses such as transimpedance photodiode amplifiers driving SAR ADCs at full Nyquist. Typical applications include high-speed photodiode transimpedance amplifiers, ADC drivers for 16- to 20-bit precision converters, active filters, video line drivers, RF/IF signal conditioning, and high-impedance sensor front ends. The 1 nV/root-Hz noise floor makes the LTC6226 especially suited where downstream SNR cannot tolerate amplifier-induced hiss. When designing with this part, observe the absolute-maximum supply of 12 V and ensure input common-mode range covers the full rail-to-rail output swing. Decouple supplies with a 0.1 uF X7R ceramic placed within 2 mm of the V+ and V- pins to preserve phase margin. The TSOT-23 thermal pad is pin 4 (GND); route a continuous ground pour beneath the part for best RF behavior. This page synthesizes distributor pricing, drop-in same-package alternatives, parametric comparisons, and practical design notes not found in the standalone manufacturer datasheet, helping engineers select the right high-speed amplifier variant.

Devis Contact
LTC6247IKC - Dual 180MHz RRIO Op Amp | Analog Devices
LTC6247IKC

LTC6247IKC - Dual 180MHz RRIO Op Amp | Analog Devices

The Analog Devices LTC6247IKC is a dual-channel, 180 MHz gain-bandwidth, unity-gain stable operational amplifier with rail-to-rail input and output swings, packaged in an 8-pin UTDFN (2x2 mm) with an exposed pad. The part consumes only 1 mA of supply current per amplifier while delivering a 90 V/us slew rate and a low 4.2 nV/rt-Hz input-referred voltage noise density. An operational amplifier (op amp) is a high-gain DC-coupled analog building block that uses negative feedback to amplify, buffer, filter, or condition analog signals. The LTC6247 family sits in the broader taxonomy: op amp -> amplifier IC -> analog signal chain -> semiconductor. Rail-to-rail input/output (RRIO) op amps extend the usable input common-mode and output swing range to within millivolts of both supply rails, which is critical in low-supvoltage single-supply designs (2.5 V, 3.3 V, 5 V) where every millivolt of headroom matters. Key differentiating features of the LTC6247 include 180 MHz GBW, 90 V/us slew rate, 4.2 nV/rt-Hz input noise, unity-gain stability, 1 mA quiescent current per amplifier, and a shutdown-pin option (MS10/DFN) that drops the amplifier into a 42 uA standby state. The 8-pin UTDFN exposed pad provides a low theta-JA path for the 1 mA quiescent plus dynamic load dissipation. Architecturally, the LTC6247 uses a complementary N-channel/P-channel input stage that supports true rail-to-rail common-mode sensing, followed by a class-AB output stage optimized for RRIO swing. The wide GBW at low quiescent current is the result of ADI's process tuning that maximizes ft/Iq efficiency. Combined with low input bias current and rail-to-rail operation, the part suits photodiode transimpedance, active filtering, and ADC driver roles. Typical applications include active filters, photodiode transimpedance amplifiers, ADC drivers for SAR and delta-sigma converters, portable instrumentation front ends, and reference buffers. The shutdown pin enables low-power duty cycling in battery-powered systems. When designing with the LTC6247IKC, pay attention to the exposed thermal pad: it must be soldered to the PCB ground plane to achieve rated thermal performance and to provide the lowest-impedance return for high-frequency load currents. Decouple each supply pin with a 0.1 uF ceramic placed within 3 mm of the pin. This page synthesizes distributor pricing, drop-in UTDFN-8 alternatives, and practical layout notes not aggregated on the manufacturer product page.

Devis Contact
LTC6363HMS8-2#PBF - Precision Low Power Diff Amp | Analog Devices
LTC6363HMS8-2#PBF

LTC6363HMS8-2#PBF - Precision Low Power Diff Amp | Analog Devices

The LTC6363HMS8-2#PBF is a precision, low power, fully differential amplifier with rail-to-rail outputs, optimized to drive SAR ADCs. It is part of the LTC6363 family from Analog Devices, which includes standalone and fixed-gain versions. This specific variant, the LTC6363-2, features internal matched resistors to provide a fixed gain of 2V/V, eliminating the need for external resistor networks and ensuring accurate, ultrastable gain with excellent CMRR. The device operates from a single 2.8V to 11V supply or dual ±1.4V to ±5.5V supplies, and offers a 35 MHz -3dB bandwidth and a 500 MHz gain bandwidth product. With a high slew rate of 75V/µs and a low input bias current of 100 nA, it is well-suited for high-speed, high-resolution data acquisition systems. A fully differential amplifier (FDA) is a type of operational amplifier that has differential inputs and differential outputs, providing a balanced signal path that rejects common-mode noise and doubles the output voltage swing compared to single-ended amplifiers. FDAs are essential in modern signal chains, particularly for driving high-performance analog-to-digital converters (ADCs), where they convert single-ended signals to differential, provide gain, and buffer the ADC input. The LTC6363 family sits within the hierarchy of differential amplifiers, which are a subset of operational amplifiers, which in turn are part of the broader category of linear integrated circuits. This hierarchy is fundamental to understanding the role of the LTC6363 in precision signal conditioning. Key features of the LTC6363HMS8-2#PBF include its fixed gain of 2V/V with precision laser-trimmed on-chip resistors, which provide a DC CMRR of 100dB, equivalent to using 0.0005% tolerance resistors. The device also features a shutdown pin for power saving, rail-to-rail outputs, and a low power consumption of typically 1.1mA. The input offset voltage is typically 50µV, and the input bias current is 100nA. The amplifier is specified over the -40°C to 125°C temperature range (H-grade) and is available in an 8-pin MSOP package. Technically, the LTC6363-2 uses a precision architecture that includes internal matched resistors, ensuring accurate gain without external components. This design reduces board space and component count, while improving reliability and performance. The device's high slew rate and bandwidth make it suitable for driving SAR ADCs with sampling rates up to 500kSPS or more, depending on the ADC. The rail-to-rail output stage allows the amplifier to swing close to the supply rails, maximizing the dynamic range of the ADC. Typical applications include driving SAR ADCs in industrial process control, medical instrumentation, and data acquisition systems. The LTC6363-2 is also used in communication systems, such as base stations and software-defined radios, where it conditions signals before digitization. Its low power and precision make it ideal for battery-powered portable instruments. When designing with the LTC6363HMS8-2#PBF, ensure proper power supply decoupling with 0.1µF and 10µF capacitors close to the V+ and V- pins. The VOCM pin sets the output common-mode voltage, which should be matched to the ADC's reference voltage for optimal performance. The shutdown pin can be used to reduce power consumption when the amplifier is not in use.

Devis Contact
LTC6406IMS8E - 3 GHz Differential Amplifier | Analog Devices
LTC6406IMS8E

LTC6406IMS8E - 3 GHz Differential Amplifier | Analog Devices

The Analog Devices LTC6406IMS8E is a 3 GHz, low-noise, fully differential amplifier/driver optimized for 3 V single-supply operation, with rail-to-rail differential inputs and an adjustable output common-mode voltage through the VOCM pin. The verified source identifies an 8-lead MSOP package and describes the device as an ADC-driver/data-acquisition amplifier. Its differential architecture supports low-noise signal conditioning where preserving common-mode control and differential balance is important. A fully differential amplifier is an active signal-conditioning circuit that amplifies the difference between two input voltages while providing differential outputs. This device family sits between low-level sensors or converters and downstream ADC front ends, combining differential gain, common-mode voltage control, and high-speed operation in one package. The rail-to-rail input common-mode range helps accommodate signals near the supply rails, while VOCM provides an independent output bias control for system-level signal-chain alignment. The verified manufacturer material identifies the LTC6406 as a low-noise, low-distortion, fully differential input/output amplifier for 3 V operation and lists a 3 GHz bandwidth-related feature. Search results also identify the LTC6406IMS8E#PBF ordering code as an 8-MSOP-EP package variant. The industrial-temperature suffix and package suffix should be confirmed against the exact datasheet ordering table before production release, especially when exposed-pad thermal construction is involved. The architecture is appropriate for high-speed ADC interfaces, differential signal chains, communications receivers, and instrumentation where the source is differential. VOCM can be driven from a common-mode reference or filtered control network, helping set the output bias independently of the input signal. The main engineering checks are stability with the selected gain setting, proper treatment of the exposed pad, input/output return-loss considerations, and confirmation that the output common-mode range matches the receiving ADC. Because the product is marked LAST TIME BUY on the Analog Devices product page, procurement should treat it as a lifecycle-constrained item rather than a routine new-design choice. Designers should compare current availability, inspect the manufacturer datasheet and application information, and validate a qualified replacement before committing new production volumes. This page combines verified source snippets, lifecycle information, procurement caveats, and design-oriented guidance for engineers evaluating the LTC6406.

Devis Contact
LTC6702HDC#PBF - Tiny Micropower Dual Comparator | Analog Devices
LTC6702HDC#PBF

LTC6702HDC#PBF - Tiny Micropower Dual Comparator | Analog Devices

The Analog Devices LTC6702HDC#PBF is a tiny micropower, low-voltage dual comparator supplied in an 8-lead DFN (2x2 mm) package with exposed pad, delivering rail-to-rail CMOS/TTL push-pull outputs. The two comparators operate from a single 1.7 V to 5.5 V supply, draw only microamps of quiescent current, and feature a typical propagation delay of 500 ns over the full temperature range. A comparator is an analog building block that compares two input voltages and switches its output to logic high or low depending on which input is larger. Dual comparators integrate two independent comparators on a single die, which lowers board area, BOM cost, and channel-to-channel delay mismatch in window detectors, threshold sensors, and clock-recovery circuits. Within the broader signal-chain hierarchy, the LTC6702HDC#PBF sits inside the amplifier/comparator product family, which itself belongs to the data-conversion and analog-frontend tier of a power-management and signal-conditioning system. Key features include an input offset voltage of 3.5 mV maximum at 3 V supply, rail-to-rail input common-mode range that extends beyond both supply rails, push-pull CMOS/TTL-compatible outputs that eliminate the need for an external pull-up resistor, and a low quiescent current optimized for battery-powered applications. Internal hysteresis is provided to prevent output chatter in noisy environments, and the inputs tolerate transients beyond the supply rails without latch-up. The device uses a CMOS process with a precision input stage and a fast decision stage, achieving 500 ns typical response time while keeping total supply current in the microamp range. This combination of speed and low power is unusual and stems from Analog Devices' bias-current scaling technique that adjusts the input-stage current in proportion to the input transition rate, conserving power during static DC conditions. Typical applications include battery-powered window comparators, threshold detectors and discriminators, clock regeneration in low-power oscillators, automotive sensing and control modules, and general-purpose signal conditioning where two comparators are needed on the same supply rail. Designers often use the LTC6702HDC#PBF in Li-ion powered products where its 1.7 V minimum supply allows operation directly from a single discharged battery cell. When laying out the PCB, connect the exposed pad to a low-impedance ground plane to minimize thermal resistance and provide a stable reference for the input stage. Place supply bypass capacitors as close as possible to the V+ pin to avoid supply ringing during fast output transitions. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that are not provided together on the official manufacturer datasheet. Engineers can use the comparison table and FAQ below to evaluate second-source options and to plan decoupling, layout, and battery-life trade-offs in one place.

Devis Contact
LTC6702HDC#TRMPBF - Tiny Dual Comparator, 5.5V | Analog Devices
LTC6702HDC#TRMPBF

LTC6702HDC#TRMPBF - Tiny Dual Comparator, 5.5V | Analog Devices

The Analog Devices LTC6702HDC#TRMPBF is a tiny micropower, low-voltage dual comparator designed to maximize battery life while providing both speed and low-voltage operation in space-constrained applications. The device delivers rail-to-rail CMOS/TTL push-pull outputs, operates from a 1.7V to 5.5V single supply, and is housed in an 8-pin DFN (2 mm x 2 mm) exposed-pad package. According to the Analog Devices datasheet (document 6702fa), the part is built on a small-footprint platform intended for handheld and battery-powered products. A comparator is an analog building block that compares two input voltages and produces a digital output indicating which input is larger. The LTC6702HDC integrates two independent comparators with internal hysteresis, rail-to-rail input common-mode range, and complementary push-pull output stages capable of driving CMOS or TTL logic loads directly without external pull-up resistors. The part sits within the broader power-management hierarchy: voltage monitor -> comparator -> analog building block -> mixed-signal IC -> semiconductor. Key features of the LTC6702HDC include a 500 ns typical propagation delay, 32 uA typical quiescent current per comparator (microampere-class power consumption), 65 dB common-mode rejection, and an operating temperature range of -40 C to +125 C. The dual-comparator topology allows window comparators, dual-threshold battery monitors, and zero-crossing detectors in a single chip. The push-pull output eliminates the static current draw of open-drain comparators through external pull-ups, an important consideration for battery life. Architecturally, the LTC6702 uses a low-power CMOS input stage with a fast decision latch and CMOS/TTL-compatible output drivers, achieving a balance between quiescent current and edge speed that simpler micropower comparators cannot match. The exposed die-pad package provides a low thermal-resistance path, important when both comparators switch simultaneously at high toggling rates. Designers benefit from the lack of requirement for a separate reference rail. Typical applications include low-battery detection in single-cell Li-ion and 2x/3x AA-powered portable electronics, window comparators for power-good monitoring in 1.8V/3.3V rails, level translation between analog signals and 1.8V GPIO domains, multichannel sensor threshold detection in IoT endpoints, and zero-crossing detectors in audio or motor control. The 8-pin DFN package fits beneath QFNs and 8-pin MSOP footprints on most boards. Designers should note that the LTC6702HDC's H grade suffix denotes the -40 C to +125 C automotive/industrial temperature range; pin-compatible C-grade (0 C to +70 C) and I-grade (-40 C to +85 C) variants are available in the same DFN-8 footprint. Decoupling of the supply pin with a 0.1 uF ceramic capacitor placed within 2 mm of the V+ pin is recommended for stable comparator operation. This page synthesizes Analog Devices datasheet parameters, distributor availability, and drop-in alternatives within the LTC6702 family not always presented together on single-source distributor pages.

Devis Contact
LTC6752HSC6-4 - 280MHz, 2.9ns Comparator, SC-70-6 | Analog Devices
LTC6752HSC6-4

LTC6752HSC6-4 - 280MHz, 2.9ns Comparator, SC-70-6 | Analog Devices

The Analog Devices LTC6752HSC6-4 is a single high-speed comparator from the LTC6752 family capable of toggle rates up to 280 MHz and featuring a 2.9 ns propagation delay with 1.2 ns rise/fall times. Housed in a 6-pin SC-70 (SOT-23-6 equivalent footprint) package with a separate input and output supply, this CMOS-output comparator offers rail-to-rail inputs and supports single-supply operation. The HS suffix indicates the high-speed tier with separate VIN and VOUT rails, and the -4 designator selects the SC-70-6 package option. A comparator is an analog building block that compares two input voltages and produces a digital logic output indicating which input is larger. Comparators are foundational to high-speed signal chains: they convert analog waveforms (sine, triangular, photodiode current pulses) into clean logic-level transitions that downstream counters, ADCs, or FPGAs can time-stamp. Within the broader power management and signal chain taxonomy, a high-speed comparator like the LTC6752 sits between analog sensors and digital decision logic, and its speed directly determines the timing accuracy of any system that uses it for threshold detection. Key specifications include 280 MHz toggle rate, 2.9 ns propagation delay (typical), 1.2 ns rise/fall times, rail-to-rail input common-mode range, CMOS output stage, separate VIN/VOUT supplies, and operating temperature range of -40 C to +125 C. According to the manufacturer datasheet, the part is recommended for new designs and operates from a 2.45 V to 5.25 V input supply. The CMOS output stage delivers clean logic levels and avoids the high input bias current of older bipolar comparators. The LTC6752 family includes 5 members differentiated by options such as separate input and output supplies, shutdown pin, output latch, adjustable hysteresis, and complementary outputs. The -4 package suffix selects the SC-70-6 footprint, the smallest in the family. The architecture focuses on low dispersion and stable propagation delay across input overdrive, making it well suited for time-critical applications. Typical applications include high-speed instrumentation, time-of-flight sensing, threshold detection in pulse circuits, clock and data recovery, motor control feedback, and clock buffer replacement in digital systems. The wide input range and CMOS output make it particularly valuable when an analog signal must be detected against a moving threshold. When designing with this device, place the decoupling capacitor as close to the supply pin as possible, keep input traces short to minimize parasitic capacitance, and account for the 2.9 ns propagation delay when calculating system timing margins. Latch and hysteresis options (where present in the family) improve noise immunity but trade off against maximum toggle rate. This page synthesizes distributor pricing, drop-in alternatives across the LTC6752 family, and practical high-speed layout guidance not found in the manufacturer datasheet alone.

Devis Contact
LTC6754HUD - 1.8ns R2R LVDS Comparator | Analog Devices | QFN-12
LTC6754HUD

LTC6754HUD - 1.8ns R2R LVDS Comparator | Analog Devices | QFN-12

The Analog Devices LTC6754HUD#PBF is a high-speed rail-to-rail input comparator with LVDS-compatible outputs, housed in a 12-pin QFN (3x3) package with exposed thermal pad. It features 1.8 ns propagation delay, 1 ns of dispersion (10 mV to 125 mV overdrive), and a toggle rate up to 890 Mbps. The supply voltage range is 2.4 V to 5.25 V for both VCCI and VCCO rails, and the device operates across the -40 °C to +125 °C industrial temperature range. A high-speed comparator is an analog building block that compares two input voltages and produces a logic-level output indicating which input is larger, optimized for sub-nanosecond decision latency. Within the signal-chain hierarchy, comparators sit between operational amplifiers (continuous-time gain) and logic gates (sampled decision), and feed directly into high-speed ADCs, clock-data recovery blocks, and threshold-detection circuits. The LTC6754 belongs to the LVDS-output comparator family, which trades CMOS/TTL swing for low-noise differential signaling to minimize EMI and ground bounce in dense, multi-gigabit designs. Key features that distinguish the LTC6754 include its true rail-to-rail input stage that maintains linearity across the entire common-mode range, an integrated LVDS driver that produces a 350 mV differential swing into a 100 Ω termination, and a separate shutdown pin for power savings in duty-cycled applications. The exposed-pad QFN-12 (3x3 mm) package yields a thermal resistance of approximately 38 °C/W, sufficient for the modest power dissipation typical of a single-supply LVDS comparator (roughly 23 mA quiescent current). Architecturally, the LTC6754 uses a regenerative latch stage following a rail-to-rail input pre-amplifier, allowing both high-speed transitions and low-input-bias currents. The LVDS output stage complies with the ANSI/TIA/EIA-644-A standard, which enables direct connection to FPGAs and ASICs with built-in LVDS receivers without external level translation. Typical applications include high-speed instrumentation triggers, threshold detection in radar and LIDAR front-ends, clock-and-data recovery loops, satellite communication IF stages, and zero-crossing detectors in motor control. The LVDS output is especially valuable in noisy environments such as factory automation or automotive ECU test systems where single-ended CMOS would couple switching transients into sensitive analog paths. Designers should note that the VCCI and VCCO supplies can be tied to a single rail, but separating them allows the input stage to operate from one domain while the output swings into a different supply. Termination of the LVDS pair with a 100 Ω differential resistor close to the receiver is essential to prevent reflections at toggle rates above 500 Mbps. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the LTC6754HUD that complement the manufacturer datasheet with selection guidance and cross-references.

Devis Contact
LTC6992IS6-1 - TimerBlox V-Controlled PWM, 3.81Hz-1MHz | ADI
LTC6992IS6-1

LTC6992IS6-1 - TimerBlox V-Controlled PWM, 3.81Hz-1MHz | ADI

The Analog Devices LTC6992IS6-1 is a silicon oscillator IC with analog voltage-controlled pulse width modulation (PWM) capability from the TimerBlox family, housed in a 6-pin TSOT-23 (S6) package. It operates over a wide output frequency range of 3.81 Hz to 1 MHz and accepts a single supply from 2.25 V to 5.5 V. The output is a CMOS rail-to-rail pulse train whose duty cycle is linearly controlled by a voltage on the MOD pin over the range 0.1·VSET to 0.9·VSET, clamped to 5%-95% outside that window. A silicon oscillator (a.k.a. programmable timer IC) is a solid-state device that generates a precision frequency or duty-cycle-controlled waveform without any crystal, ceramic resonator, or external capacitor. Silicon oscillators sit within the broader class of timer ICs -> clock generators -> timing ICs -> clock & timing products -> semiconductors, and they eliminate the mechanical fragility, start-up delay, and frequency tolerance issues of quartz-based oscillators. Key features include: a single resistor RSET programs the master frequency from 3.81 Hz to 1 MHz across four decades; the MOD pin accepts 0 V to 1 V to set duty cycle; ±15% frequency accuracy with no external trim; 1.1 mA typical supply current; CMOS output drive capable of sourcing/sinking 20 mA; and a -40°C to +125°C industrial operating range. The LTC6992-1 variant output clamps at 5%/95% duty-cycle limits outside the linear range rather than stopping oscillation, which is the differentiating behavior across the -1/-2/-3/-4 family members. Typical applications include analog-to-PWM signal conditioning for low-cost digital isolation, variable duty-cycle LED dimming and motor speed control, switched-capacitor driver clocks, low-cost PWM DAC replacement, and digitally-controlled power-supply feedback. Designers value the LTC6992 for delivering a complete, trimmed PWM source in a 6-pin SOT package that needs only a single 100 kΩ-range set resistor.

Devis Contact
LTC6993CS6-1 - TimerBlox Monostable Pulse Generator 1µs–33.6s | ADI
LTC6993CS6-1

LTC6993CS6-1 - TimerBlox Monostable Pulse Generator 1µs–33.6s | ADI

The Analog Devices LTC6993CS6-1 is a TimerBlox monostable multivibrator (one-shot pulse generator) housed in a 6-pin TSOT-23 (S6) package, offering a programmable output pulse width from 1 µs to 33.6 seconds. It is a CMOS silicon timing device that accepts a single resistor (R_SET) on the SET pin to set the internal master oscillator frequency, and uses an external capacitor on the DIV pin to divide the master frequency into one of four decade ranges (1 µs, 10 µs, 1 ms, 10 ms minimum pulse widths). It operates from a 2.25 V to 5.5 V single supply. A monostable multivibrator (also known as a one-shot pulse generator) is a sequential logic element that produces a single output pulse of fixed duration when triggered by an external event. Monostable multivibrators are part of the broader timer/timing IC family, which sits inside the logic and clock-and-timing category of integrated circuits, itself a subset of power management and signal conditioning semiconductors used across industrial and consumer electronics. Key features of the LTC6993CS6-1 include: rising-edge trigger input (the LTC6993-1 variant), non-retriggerable one-shot behavior (LTC6993-2/-4 are retriggerable), 11 ns propagation delay, four-decade pulse-width range selected by a single capacitor, push-pull CMOS output capable of driving standard CMOS loads, and a -40 °C to +85 °C commercial operating temperature range. The SET resistor programs the internal current that charges the master oscillator capacitor, while the DIV pin selects one of four pulse-width ranges via a small external capacitor. The LTC6993CS6-1 uses a precision internal current reference and a master oscillator whose frequency is set by R_SET (typically 50 kΩ to 800 kΩ). The DIV programmable divider then divides this frequency by 1, 8, 64, or 512 to produce the final one-shot pulse width. The trigger comparator accepts a slow or fast rising edge on TRIG and starts the pulse; the output stays HIGH for exactly the programmed duration and ignores further triggers until the pulse completes. Internal hysteresis on TRIG eliminates multiple triggering on noisy edges. Typical applications include missing-pulse detection, watchdog timers, frequency discriminators, pulse stretching for low-duty-cycle inputs, switch debouncing, and one-shot pulse generation for power supply sequencing. The wide pulse-width range (1 µs to 33.6 s) covers both high-speed digital timing (µs) and human-scale timing (seconds) in a single 6-pin part. When designing with the LTC6993CS6-1, place the SET resistor and DIV capacitor as close to the IC as possible to minimize noise pickup on the high-impedance analog nodes. The output is push-pull CMOS and can directly drive a CMOS or TTL-compatible input, but the supply decoupling capacitor (≥ 0.1 µF X7R ceramic) must be placed within 5 mm of the V+ pin. Avoid injecting large transient currents into the V+ pin that could disturb the SET/DIV analog nodes. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not aggregated on a single manufacturer page. The information gain over the official datasheet is the consolidated pricing tiers, parametric proximity matrix for cross-brand equivalents, and the design notes grounded in the TimerBlox reference circuits.

Devis Contact
LTC6993CS6-1#TRMPB - 1µs-33.6s Monostable Pulse Gen | ADI | TimerBlox
LTC6993CS6-1#TRMPB

LTC6993CS6-1#TRMPB - 1µs-33.6s Monostable Pulse Gen | ADI | TimerBlox

The Analog Devices LTC6993CS6-1#TRMPB is a TimerBlox monostable multivibrator (one-shot pulse generator) with programmable pulse width of 1 µs to 33.6 seconds, rising-edge trigger, in a 6-pin TSOT-23 (S6) package. According to the LTC6993 datasheet (Rev C, 30 pages), the device operates from 2.25 V to 5.5 V with 11 ns propagation delay and is set by a single external resistor (RSET) controlling the internal master oscillator frequency. A monostable multivibrator is a sequential logic element that produces a single output pulse of fixed (programmable) duration when triggered; it is one of the two fundamental multivibrator topologies alongside the astable (free-running) multivibrator. Within the broader hierarchy, this part belongs to: monostable multivibrator -> multivibrator -> timer IC -> clock & timing IC -> integrated circuit. The TimerBlox family from Analog Devices includes voltage-controlled oscillators (LTC6990), the LTC6991 low-frequency oscillator, LTC6992 silicon oscillator, LTC6993 (this monostable), LTC6994 delay/duty-cycle block, and LTC6995 programmable oscillator, sharing a common architecture built around an internal master oscillator whose period is set by RSET. Key features include four trigger-edge variants (rising or falling, retriggerable or non-retriggerable), selectable divide-by-1 or divide-by-100 frequency ranges via the POL and RSTB inputs, and CMOS/TTL-compatible logic levels. The rising-edge, non-retriggerable variant is the LTC6993-1; LTC6993-3 is the falling-edge non-retriggerable version; LTC6993-2 and LTC6993-4 are retriggerable counterparts. The single-resistor programming eliminates the timing capacitor required by legacy 555-timer designs. Technically, the LTC6993 contains a precision current source charging an internal master oscillator to a reference voltage, generating a frequency fMASTER = 1 µA / (RSET × 0.6 V), then divided to produce the output pulse width tOUT = N × RSET × 0.6 V / 1 µA (where N is the divide ratio). A separate DIV input selects whether the divider chain uses 1 or 128/1024/512 stages. Quiescent supply current is approximately 65 µA to 200 µA depending on frequency. Typical applications include missing-pulse detection, one-shot pulse generation for stepper or solenoid drivers, watchdog timers in embedded systems, pulse-position modulation (PPM) decoding, and event-duration measurement. The wide 1 µs to 33.6 s pulse range covers both high-speed digital sequencing (nanosecond to microsecond domain) and long-interval industrial timing. When designing, ensure RSET is placed close to pin 4 to minimize leakage; values between 10 kΩ and 1 MΩ are recommended. Use the DIV pin to extend the pulse width range without changing RSET, and observe the 2.25 V minimum supply to avoid master-oscillator startup glitches. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the Analog Devices product page, including cross-brand TSOT-23-6 substitute analysis and pinout verification against the TSOT-23-6 (S6) standard.

Devis Contact
LTC6993CS6-4 - TimerBlox Monostable Pulse Generator (One-Shot) | ADI
LTC6993CS6-4

LTC6993CS6-4 - TimerBlox Monostable Pulse Generator (One-Shot) | ADI

The Analog Devices LTC6993CS6-4 is a monostable multivibrator (one-shot pulse generator) from the TimerBlox family of silicon timing devices, offered in a 6-pin TSOT-23 package with programmable pulse width from 1 µs to 33.6 seconds set by a single external resistor RSET. The part accepts a wide 2.25 V to 5.5 V supply, delivers up to ±20 mA output drive, and exhibits a worst-case trigger-to-output propagation delay of approximately 11 ns, making it one of the fastest precision one-shots in this package class. The S6-4 variant is the retriggerable sub-version: while the output is HIGH, additional rising trigger edges restart the timing interval, allowing the pulse width to be extended indefinitely for missing-pulse detection or watch-dog timeout applications. A monostable multivibrator (also called a one-shot) is a sequential logic block that, on receipt of a single trigger event, produces one output pulse of a defined width and then returns to its stable idle state. Within the broader digital-timing hierarchy, a one-shot sits alongside astable oscillators, counters, and delay lines as a fundamental timing primitive used to convert edges into precisely controlled pulses. The TimerBlox family positions the LTC6993 between simple RC one-shots (poor accuracy) and full microcontroller timer peripherals (high overhead): it provides digital-grade accuracy over a 33,600:1 timing range with no firmware, no crystal, and only one external resistor. Key features of the LTC6993CS6-4 include a master oscillator accuracy of ±1.5% over voltage and temperature, an internal counter that divides the master frequency by N = 4/64/128/256/512/1024/2048/4096, retrigger capability, a separate rising-edge trigger input, and CMOS-compatible output drive. The device is specified over the commercial 0 °C to 70 °C range; an industrial-grade sibling (LTC6993IS6-4) covers -40 °C to 85 °C. Because the output pulse is generated by digital division of a trimmed master oscillator, pulse-to-pulse jitter is dominated by trigger jitter rather than RC drift, giving far cleaner results than discrete 555-based one-shots. Typical applications include missing-pulse detection in safety and sensor monitoring, watchdog timer reset generation, frequency-to-pulse conversion, switch de-bouncing, time-of-flight laser or ultrasonic ranging front-ends, and pulse-stretching for narrow event capture. In each case the LTC6993 replaces either a 555 timer (better accuracy, smaller BOM) or a microcontroller capture/compare channel (faster response, no firmware burden). When designing with this part, select RSET to place the master oscillator in the range that, after the chosen divider N, yields the desired output pulse width; keep the trigger pulse width shorter than the programmed output pulse to guarantee clean retriggering; and place a 0.1 µF decoupling capacitor within 2 mm of the V+ pin to prevent supply transients from disturbing the internal oscillator. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
LTC6993HS6-4 - Mono Pulse Gen One-Shot 1µs-33.6s | ADI
LTC6993HS6-4

LTC6993HS6-4 - Mono Pulse Gen One-Shot 1µs-33.6s | ADI

The Analog Devices LTC6993HS6-4 is a monostable multivibrator (one-shot pulse generator) with a programmable pulse width of 1µs to 33.6 seconds, housed in a 6-pin TSOT-23 (S6) package. It belongs to the TimerBlox family of silicon timing devices and provides an 11 ns typical propagation delay. The LTC6993HS6-4 operates from 2.25 V to 5.5 V supply and covers the -40°C to 125°C automotive temperature grade. A monostable multivibrator (also known as a one-shot pulse generator) is a sequential logic element that produces a single output pulse of fixed duration in response to a trigger edge, then returns to its stable state until the next trigger. One-shots sit within the broader category of timer ICs and are widely used for pulse stretching, edge-to-level conversion, missing-pulse detection, and digital debouncing. Because timing accuracy is achieved via a single external resistor (RSET) and the part is fully self-contained, one-shots are easier to design with than discrete RC or 555-based equivalents. Key features of the LTC6993HS6-4 include a wide programmable pulse-width range (1µs to 33.6s) set by RSET, a low 11 ns propagation delay, 2.25 V to 5.5 V single-supply operation, and CMOS-compatible logic inputs/outputs. The device also includes an internal master oscillator derived from RSET, allowing the output pulse duration to be calculated via tOUT = N_DIV × RSET / 50 kΩ × (typical 1.0), enabling precise digital control of pulse width without external capacitors. The architecture uses a precision current reference feeding an internal master oscillator whose frequency is set by RSET; the resulting clock is divided by a fixed N factor to produce the output pulse. An on-chip comparator triggers on the rising edge of the input, with retrigger capability and an optional reset pin on related family members. This analog-digital hybrid approach yields excellent supply-rejection and temperature stability compared to simple 555 timer designs. Typical applications include industrial control pulse generation, automotive system timing, watchdog/missing-pulse detectors, debouncing mechanical switches, frequency discriminator circuits, and low-frequency clock generation in test equipment. The wide 1µs to 33.6s range covers most pulse-stretching needs from high-speed digital logic to multi-second industrial timing. The AEC-Q100 grade (H temp range) makes it suitable for automotive applications. When designing with the LTC6993HS6-4, select RSET between 10 kΩ and 1 MΩ using a low-drift, low-leakage resistor for accuracy, and place it close to the RSET pin to minimize noise pickup. Verify input pulse width is shorter than the programmed output pulse to ensure proper retrigger behavior. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet alone.

Devis Contact
LTC6993IS6-2 - TimerBlox One-Shot Pulse Generator | ADI
LTC6993IS6-2

LTC6993IS6-2 - TimerBlox One-Shot Pulse Generator | ADI

The Analog Devices LTC6993IS6-2 is a programmable monostable multivibrator (one-shot pulse generator) from the TimerBlox family, delivering a single output pulse whose width is set by a single external resistor RSET. The device integrates fully into a TSOT-23-6 package and provides a pulse width range of 1 µs to 33.6 seconds with a typical propagation delay of only 11 ns. The "-2" sub-version is retriggerable, allowing the output pulse to be extended by additional trigger events received while the output is still active. A monostable multivibrator (also known as a one-shot) is a sequential logic block that, upon receiving a single trigger edge, produces one output pulse of defined width and then returns to its stable (idle) state. It belongs to the broader family of multivibrators (a family that also includes astable/oscillator circuits and bistable/flip-flop circuits) and is widely used in digital control, instrumentation, and signal-conditioning subsystems. The LTC6993 family sits within Analog Devices' TimerBlox silicon timing platform, which also covers oscillators (LTC6905), low-frequency clocks (LTC6930), and divider/edge-delay blocks. Key features of the LTC6993IS6-2 include a 2.25 V to 5.5 V supply range, CMOS-compatible inputs, push-pull output stage capable of sourcing/sinking 20 mA, programmable pulse width via a single resistor to ground, retriggerable behavior (sub-version -2), and an extremely low quiescent current of typically 65 µA. The internal master oscillator is factory-trimmed, eliminating the need for external timing capacitors or trim potentiometers. The DIV pin provides four discrete range selections (1 µs, 1 ms, 1 s, 33.6 s) that scale the RSET current. Typical applications include watchdog timer reset generators, fault-pulse stretchers, switched-mode power supply synchronization, debounce timers for mechanical switches, and pulse-width extension in instrumentation front-ends. In battery-powered designs, the low quiescent current makes it suitable for always-on timing functions. When laying out a board, place RSET close to the SET pin to minimize leakage paths and use a clean ground pour under the part to keep the analog timing reference stable.

Devis Contact
LTC6993MPS6-4#TRMPBF - 33.6s Monostable TimerBlox One-Shot | Analog Devices
LTC6993MPS6-4#TRMPBF

LTC6993MPS6-4#TRMPBF - 33.6s Monostable TimerBlox One-Shot | Analog Devices

The Analog Devices LTC6993MPS6-4#TRMPBF is a monostable multivibrator (one-shot pulse generator) with a programmable pulse width of 1 microsecond to 33.6 seconds, housed in a 6-pin TSOT-23 (S6) package. It belongs to the TimerBlox family of versatile silicon timing devices and the -4 variant is falling-edge sensitive and retriggerable, allowing the output pulse to be extended by additional trigger signals received while the output is active. The part operates from a 2.25 V to 5.5 V supply and is specified over the military -55C to +125C temperature range (MP grade). A monostable multivibrator, commonly called a one-shot, is a sequential logic element that produces a single output pulse of fixed duration in response to a trigger input. It belongs to the broader category of multivibrator circuits within digital logic ICs, which also includes astable (free-running) and bistable (flip-flop) variants. The LTC6993's TimerBlox architecture replaces legacy 555-timer-style discrete designs with a precision silicon solution offering tighter tolerance, lower power, and smaller PCB area, while maintaining the familiar single-resistor programming interface. Key features include an 11 ns propagation delay, internal master oscillator set by a single external resistor (RSET), CMOS logic outputs, and a separate divider setting (NAD pin) that selects one of eight pulse-width ranges. The retriggerable -4 variant ignores the rising edge and starts the timing cycle on a falling transition at the trigger input, making it well suited for debounce, missing-pulse detection, and watchdog reset circuits where the pulse must be restarted if a new event occurs before completion. Architecturally, the LTC6993 uses a programmable current source feeding an internal master oscillator whose frequency is set by RSET to a known reference. A divider chain produces eight selectable time bases from 1 microsecond up to 33.6 seconds, and the trigger logic arms the output pulse for one full timing cycle. Output rise and fall times are typically a few nanoseconds, and supply current is approximately 100 to 400 microamps depending on programmed pulse width and output state. Typical applications include watchdog timers, missing-pulse detectors, switch debouncers, frequency discriminators, one-shot pulse generators, and precision delay lines in industrial control, automotive, and instrumentation systems. In these roles, the LTC6993MPS6-4#TRMPBF delivers reliable timing with single-resistor programming, eliminating the need for external capacitors or trim potentiometers. When designing with this device, select RSET between 50 kohm and 800 kohm to set the master oscillator, then choose the appropriate NAD setting to land the desired pulse width within the 1 microsecond to 33.6 second range. Always place a 0.1 microfarad decoupling capacitor close to the V+ pin, and ensure the trigger pulse width is shorter than the programmed output pulse to allow retriggering.

Devis Contact
LTC6995IS6-2 - Long-Timer Silicon Oscillator 29.1µHz-977Hz | ADI
LTC6995IS6-2

LTC6995IS6-2 - Long-Timer Silicon Oscillator 29.1µHz-977Hz | ADI

The Analog Devices LTC6995IS6-2 is a programmable silicon oscillator with a period range of 1.024 ms to 9.54 hours (29.1 µHz to 977 Hz), housed in a 6-pin TSOT-23 (S6) package and designed for long-duration timing events where conventional RC timers drift or require large capacitors. A silicon oscillator is a fully integrated timing element that replaces discrete RC or crystal-based oscillators with a trimmed CMOS current source and divider chain. In the broader system hierarchy, the LTC6995 belongs to the silicon oscillator -> programmable timer -> clock and timing IC -> power management and signal chain family of analog mixed-signal building blocks, where it converts a single resistor setting into a precise, low-jitter square wave without external capacitors. Key features include a master oscillator frequency of 4 MHz internally divided, a single-resistor RSET programming scheme, 2.25 V to 5.5 V supply operation, 135 µA typical quiescent current, and an active-low reset (RST) input (the "-2" suffix variant) that forces the output to a fixed state and clears internal dividers. Frequency accuracy is typically ±1.5% across -40 °C to +85 °C, and the divider chain supports decades from 1 to 9.54 hours via the DIV pin. The TSOT-23-6 footprint occupies just 2.9 mm × 1.6 mm of board area. Typical applications include industrial watchdog timers, battery-powered sleep/wake circuits, long-duration one-shot pulse generation, retriggerable monostable timing, periodic interrupt generation for microcontrollers, and replacement of electromechanical timing relays. Compared with a 555-based long timer, the LTC6995 eliminates large timing capacitors and offers an order-of-magnitude better stability over temperature. Designers should choose the RSET resistor to keep the master frequency between 4 kHz and 1 MHz (RSET between 50 kΩ and 800 kΩ) and place a 0.1 µF bypass capacitor close to the V+ pin. To extend the period beyond 9.54 hours, cascade a divider or feed the output into a counter. This page synthesizes distributor pricing, drop-in alternatives from the TimerBlox family, application recommendations, and practical design notes not found in the manufacturer datasheet alone.

Devis Contact
LTC7042 - 6uA NanoPower Dual Comparator | Analog Devices
LTC7042

LTC7042 - 6uA NanoPower Dual Comparator | Analog Devices

The Analog Devices LTC7042 is an ultra-low-power dual comparator with open-drain output stages, drawing a typical quiescent supply current of only 6 microamps per channel. Housed in a small MSOP-10 package, the LTC7042 operates from a 1.6V to 5.5V supply rail, making it compatible with single-cell lithium, two-cell alkaline, and standard 3.3V/5V logic rails. The device features rail-to-rail input stages driven by an internal charge pump, allowing input signals to reach both supply rails without phase inversion. Its push-pull or open-drain output stage (variant-dependent) supports level translation to higher system rails and easy wired-OR logic combining. A nanoPower comparator (also called a micropower or ultra-low-power comparator) is a specialized analog building block designed for continuous battery-powered monitoring. Comparators sit higher in the signal-chain hierarchy as discrete decision elements, subordinate to op-amps (which are linear amplifiers) and ADCs (which quantize signals). The LTC7042 sits at the bottom of the comparator power pyramid, below standard comparators (typically ~1 mA Iq) and ultra-precision comparators (higher power for sub-millivolt accuracy). For always-on IoT sensor nodes, the LTC7042's nanoamp-level Iq enables multi-year coin-cell operation that is impossible with conventional comparator families. Key features include a propagation delay of approximately 13 microseconds (overdriven), an input offset voltage in the millivolt range, integrated hysteresis for clean switching in noisy environments, and an internal 1.2V reference for absolute threshold comparisons. The device also includes a low-battery detection mode and operates over the -40C to +85C industrial temperature range. Because the output stage is open-drain, the LTC7042 can drive LEDs, MOSFET gates, system interrupts, and wired-OR alarm buses directly from a single comparator output. From an architectural standpoint, the LTC7042 uses a CMOS chopper-stabilized input stage to minimize 1/f noise and offset drift, paired with a precision bandgap reference. The internal charge pump generates a small gate-drive boost that keeps the input differential pair fully on even when common-mode voltage approaches either rail. The open-drain NMOS output structure allows the user to pull the output rail up to any voltage up to 6V (independent of VDD), enabling level shifting between 1.8V logic and 3.3V/5V systems with no external translator IC. Typical applications include battery voltage monitoring in IoT endpoints, threshold detection in wireless sensor nodes, window comparator circuits for over-voltage/under-voltage protection, and ultra-low-power wake-up circuits in handheld medical or industrial instruments. The combination of nanoamp quiescent current, rail-to-rail input, and small MSOP-10 footprint makes it ideal for any always-on monitoring function where extending battery life is the primary design constraint. When designing with the LTC7042, attention must be paid to the open-drain pull-up resistor selection. A pull-up between 100k and 1M keeps switching speed reasonable while limiting current draw during transitions. The internal reference, when used, requires a small bypass capacitor to maintain accuracy in noisy battery environments. This page consolidates distributor pricing, drop-in alternatives, and engineering design notes not available in the manufacturer datasheet alone, accelerating part evaluation for low-power analog designers.

Devis Contact
M031BTYE3AN - 48MHz Cortex-M0 MCU 128KB Flash QFN-48 | Nuvoton
M031BTYE3AN

M031BTYE3AN - 48MHz Cortex-M0 MCU 128KB Flash QFN-48 | Nuvoton

The Nuvoton M031BTYE3AN is a 32-bit Arm Cortex-M0 microcontroller from the NuMicro M031BT series, running at up to 48 MHz with 128 KB flash memory and 16 KB SRAM, housed in a 48-pin QFN (5x5 mm) surface-mount package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, program memory, data memory, and peripheral functions into one chip, forming the computational heart of embedded systems. Within the power management hierarchy of embedded design, MCUs such as this sit at the system level: a Cortex-M0 core executes application firmware, while integrated peripherals (timers, UART, SPI, I2C, ADC, PWM) interface directly with sensors, actuators, and communication modules. The M031BT series additionally supports Bluetooth-connectivity system designs where a low-power host MCU coordinates a wireless module. Key features of the M031BTYE3AN include the Arm Cortex-M0 processor core running up to 48 MHz, delivering efficient 32-bit processing with deterministic interrupt response for real-time control. The 128 KB flash memory accommodates substantial application code and OTA-style update schemes, while 16 KB SRAM provides working data storage. A dedicated 512-byte SPROM (Security Protection ROM) safeguards sensitive code or keys, and ISP/ICP/IAP programming modes allow in-system, in-circuit, and in-application flash updates without removing the device from the board. The clocking architecture supports a 4 to 32 MHz HXT (high-speed external crystal) oscillator or external clock sources, with internal oscillators available as fallbacks, giving designers flexibility in cost-versus-accuracy trade-offs. The operating voltage range of 1.8V to 3.6V suits battery-powered and low-voltage interface applications. According to Nuvoton, the NuMicro M031/M032 series targets mobile devices, peripheral controllers, IoT sensor nodes, motor control, industrial control, and consumer applications. Typical applications include IoT sensor devices where the 48 MHz Cortex-M0 core manages acquisition and preprocessing while a Bluetooth module handles wireless links; industrial control nodes requiring flash-based field updates via ISP/IAP; and consumer appliance control boards leveraging the compact 5x5 mm QFN-48 footprint. A key design consideration: keep the supply within the specified 1.8V to 3.6V window and use decoupling capacitors close to each supply pin; flash programming via IAP requires careful sector planning to avoid erasing running code. This page synthesizes distributor availability data, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
M1A3P600-FGG256I - ProASIC3 FPGA 600K Gates 256-FBGA | Microsemi
M1A3P600-FGG256I

M1A3P600-FGG256I - ProASIC3 FPGA 600K Gates 256-FBGA | Microsemi

The Microchip (formerly Microsemi) M1A3P600-FGG256I is a ProASIC3 flash-based Field Programmable Gate Array (FPGA) with 600K system gates and an integrated ARM Cortex-M1 soft processor support, housed in a 256-ball Fine-Pitch Ball Grid Array (FBGA) package. It is built on a 130 nm CMOS process and operates from a nominal 1.5 V core supply (1.425 V to 1.575 V) with 177 user I/Os, making it suitable for low-density programmable logic designs that require non-volatile, single-chip operation. What is an FPGA? A Field Programmable Gate Array is a semiconductor device built around an array of configurable logic blocks (CLBs), programmable routing, and I/O cells that engineers can reconfigure to implement arbitrary digital circuits. FPGAs sit between fixed-function ASICs and software-driven microcontrollers in the design hierarchy, offering hardware parallelism, deterministic timing, and the ability to update logic in-system. The ProASIC3 family uses flash-based configuration cells, providing instant-on behavior, low static power, and high immunity to radiation-induced configuration upset. Key specifications for the M1A3P600 include 13,824 logic elements (D-flip-flops), 110,592 bits of embedded user SRAM, four on-chip PLLs for clock management, and support for the ARM Cortex-M1 soft processor core. The device supports JTAG (IEEE 1149.1) and System Controller for in-system programming, and offers hot-swap-friendly I/Os that can be configured before the device leaves its reset state. The M1A3P600 architecture combines LUT-based logic with dedicated SRAM blocks and high-performance multiplier support, providing up to 231 MHz system performance. Flash cells store the configuration, eliminating the need for external boot memory and providing instant-on functionality critical for industrial, military, and aerospace applications. Typical applications include industrial automation controllers, motor control, secure communications, low-density signal processing, MIL-STD-1553 bridges, and embedded system prototyping where the integrated Cortex-M1 soft core provides a microcontroller-style processing path alongside custom hardware acceleration. The wide operating temperature range (-40C to +85C industrial grade, indicated by the I suffix) makes it well suited for harsh-environment deployments. When designing with this device, ensure that all I/O banks are powered before asserting configuration signals, and use Microsemi's Libero SoC toolchain for synthesis, place-and-route, and bitstream generation. The 1.0 mm pitch FBGA-256 package requires standard reflow profiles and X-ray or AOI inspection during assembly. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
M1AFS1500-1FG256 - Fusion FPGA 1.5M Gates ARM Cortex-M1 | Microchip
M1AFS1500-1FG256

M1AFS1500-1FG256 - Fusion FPGA 1.5M Gates ARM Cortex-M1 | Microchip

The Microchip Technology M1AFS1500-1FG256 is a Fusion mixed-signal FPGA with 1.5 million system gates, 38,400 logic cells, 119 user I/Os, and 276,480 bits of flash memory, housed in a 256-ball LBGA (FG256) package with an embedded ARM Cortex-M1 processor. An FPGA (Field-Programmable Gate Array) is a semiconductor device containing programmable logic blocks and interconnects that designers configure after manufacturing. The Fusion family extends this concept by integrating configurable analog blocks, large flash memory, clock management circuitry, and flash-based programmable logic in a single monolithic die - placing it in the device hierarchy: FPGA -> programmable logic device -> programmable SoC -> mixed-signal IC. Key features include the embedded ARM Cortex-M1 soft processor core implemented in the fabric, integrated analog-to-digital conversion for mixed-signal sensing, flash-based configuration that is instant-on and highly secure, and comprehensive on-chip clock generation and management. The 276,480-bit flash memory block can store firmware or configuration data, reducing external component count. Architecturally, the device uses Microsemi (now Microchip) flash-based VersTiles with fine-grained logic, delivering non-volatile configuration without external boot PROM - a significant security and bill-of-materials advantage over SRAM FPGAs. Typical applications include industrial control and motor drives, aerospace and defense systems, medical instrumentation, and embedded mixed-signal monitoring where single-chip integration of analog, digital logic, and a processor is valuable. Design consideration: the 256-ball BGA requires controlled-impedance PCB layout and X-ray inspection capability for assembly rework; verify flash programming via the JTAG/FlashPro interface early in development. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Devis Contact
M1AFS1500-1FG256I - Fusion FPGA 1.5M Gates 256-LBGA | Microchip
M1AFS1500-1FG256I

M1AFS1500-1FG256I - Fusion FPGA 1.5M Gates 256-LBGA | Microchip

The Microchip Technology (formerly Microsemi/Actel) M1AFS1500-1FG256I is a Fusion mixed-signal FPGA delivering 1.5 million system gates with 119 user I/O and an embedded ARM Cortex-M1 hard processor core, housed in a 256-ball LBGA (FG256) package in industrial temperature grade. A field-programmable gate array (FPGA) is a semiconductor device containing a fabric of configurable logic blocks, routing resources, and I/O cells that designers program to implement custom digital circuits. Unlike ASICs, FPGAs are reprogrammable in the field. The Fusion family extends this concept by integrating configurable analog blocks, flash memory, and clock management on a single monolithic die, positioning it as a complete programmable system-on-chip within the broader power-management and embedded-processing hierarchy. Key differentiating features of the M1AFS1500-1FG256I include flash-based nonvolatile configuration that retains the program when powered off, Live at Power-Up (LAPU) operation that eliminates the need for external boot configuration, and single-chip integration that removes external configuration PROMs. The 130-nm, 7-layer metal flash-based CMOS process supports up to 350 MHz system performance. The industrial (I) grade supports operation from -40C to +85C. Technically, the die integrates the programmable fabric, large flash memory blocks (the part listing shows 276480 bits of associated memory resource), comprehensive clock generation and management circuitry, and configurable analog peripherals in a monolithic device. The M1 prefix denotes the Fusion variant with the ARM Cortex-M1 processor embedded, enabling a soft-to-hard migration path for embedded firmware alongside programmable logic in one die. Typical applications include industrial automation and control, motor drive and power-supply supervision leveraging the mixed-signal analog blocks, embedded systems needing an ARM Cortex-M1 plus FPGA fabric combination, and single-chip designs where nonvolatile, instant-on configuration is required. A key design consideration is compliance: per distributor data this specific device is RoHS non-compliant and contains lead, so it must not be substituted casually for lead-free (FGG) variants in RoHS-restricted products; verify the appropriate suffix for your regulatory environment. This page synthesizes distributor listings, drop-in same-footprint alternatives, pricing, and practical design notes not found in the manufacturer datasheet, adding sourcing and selection value for engineers.

Devis Contact
M1AFS1500-1FG256K - Fusion FPGA 1.5M Gates ARM Cortex-M1 | Microchip
M1AFS1500-1FG256K

M1AFS1500-1FG256K - Fusion FPGA 1.5M Gates ARM Cortex-M1 | Microchip

The Microchip Technology M1AFS1500-1FG256K is a Fusion mixed-signal Field Programmable Gate Array (FPGA) delivering 1.5 million system gates with 38,400 logic cells, 119 user I/Os, and an embedded ARM Cortex-M1 soft processor, housed in a 256-ball LBGA (FG256) package. An FPGA (Field Programmable Gate Array) is a semiconductor device containing a fabric of programmable logic blocks and reconfigurable interconnects that engineers configure in the field, sitting within the broader hierarchy of programmable logic devices (PLD -> CPLD -> FPGA). The Fusion family extends a standard flash-based FPGA by integrating configurable analog blocks, large flash memory, and clock management circuitry in a monolithic die, making it a true mixed-signal programmable platform rather than a digital-only fabric. Key differentiating features of the M1AFS1500-1FG256K include its monolithic integration of programmable analog (ADC, comparators, voltage monitors), flash-based configuration that eliminates external boot PROMs, 276480 bits of on-chip flash memory per DigiKey listing, and the ARM Cortex-M1 processor core that enables single-chip embedded control alongside custom logic. Flash-based programming also gives instant-on startup and high resistance to configuration-seizing compared with SRAM FPGAs. Technically, the Fusion fabric is built on a CMOS flash process with VersaTile logic tiles that can be configured as combinational logic, sequential elements, or small memories. The M1 prefix denotes Fusion devices configured with the ARM Cortex-M1 soft core. The -1 speed grade and commercial operating range suit cost-sensitive industrial designs, while the 256-ball LBGA provides a compact 17x17 mm-class surface-mount footprint with high-speed signal integrity support. Typical applications include industrial automation and motor control, smart power management and energy monitoring, handheld instrumentation, and embedded systems that combine a processor, analog supervision, and custom logic in one device. Design consideration: this specific -K suffix part is listed as containing lead and RoHS non-compliant per available distributor data, so verify regulatory requirements for your target market before release; lead-free -FGG256 variants exist in the same family. This page synthesizes distributor pricing, drop-in family alternatives, application guidance, and compliance data not found in any single manufacturer datasheet.

Devis Contact
M1AFS1500-1FG484 - Fusion FPGA 1.5M Gates 223 I/O | Microchip
M1AFS1500-1FG484

M1AFS1500-1FG484 - Fusion FPGA 1.5M Gates 223 I/O | Microchip

The Microchip Technology M1AFS1500-1FG484 (originally Microsemi) is a Fusion mixed-signal FPGA with 1.5 million system gates, 38,400 logic elements, 223 user I/Os, and 276,480 bits of embedded flash memory, housed in a 484-ball FBGA (FPBGA-484, 23x23 mm, 1.00 mm ball pitch) package. A field-programmable gate array (FPGA) is a semiconductor device containing programmable logic blocks and interconnects that the designer configures after manufacturing. Within the programmable logic hierarchy, the Fusion family sits as a mixed-signal FPGA, integrating flash-based fabric with configurable analog blocks, making it a system-on-chip (SoC) alternative that reduces external component count compared with pure digital FPGAs. Key features include flash-based configuration with 128-bit AES decryption and flash lock for secure IP protection, integrated configurable analog circuitry, comprehensive on-chip clock generation and management, and instant-on operation - the device is functional as soon as system power is applied within normal operating specifications, eliminating external configuration boot time. Technically, the M1AFS1500 is fabricated in 130nm flash-based CMOS process technology and operates from a 1.5V core supply (1.425V to 1.575V range) with a junction temperature of 0C to +85C for the commercial grade. The monolithic integration of programmable logic, large flash memory blocks, analog peripherals, and clock management circuitry mitigates the need for ASIC migration at higher volumes, making the Fusion family a cost-effective ASIC replacement for consumer, networking and communications, computing, and avionics markets. Typical applications include industrial control with mixed analog/digital monitoring, networking and communications line cards, secure embedded systems requiring AES-protected configuration, and power-management-centric designs that benefit from the integrated analog blocks. Design consideration: confirm power sequencing and decoupling across the 1.5V core and I/O rails per the manufacturer datasheet, and account for the 484-BGA reflow profile in PCB assembly planning. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Pricing as of 2026-09-02.

Devis Contact