Microcontrôleurs

Produits (18688)

R5F562T7DDFP#V1 - 100MHz RX62T MCU 128KB Flash | Renesas
R5F562T7DDFP#V1

R5F562T7DDFP#V1 - 100MHz RX62T MCU 128KB Flash | Renesas

The Renesas R5F562T7DDFP#V1 is a 32-bit RX62T microcontroller built around the high-performance RX600 CPU core, operating at a maximum frequency of 100 MHz and delivering up to 165 DMIPS with an integrated single-precision FPU. It integrates 128 KB of on-chip flash memory, 8 KB of SRAM, and a rich set of motor-control peripherals including the Multi-Function Timer Pulse Unit (MTU3), General PWM Timer (GPT), high-speed 12-bit A/D converter, and 10-bit A/D converter, all housed in a 100-pin LFQFP (14x14 mm) package. A 32-bit microcontroller (MCU) is a programmable processor-on-a-chip that integrates CPU core, non-volatile program memory, working RAM, and a wide variety of analog and digital peripherals onto a single silicon die. Within the broader electronics taxonomy, MCUs sit under microcontrollers -> microprocessors -> embedded processors -> semiconductors, and they are the central computational element in nearly every modern electronic product from washing machines to industrial robots. The RX62T family specifically belongs to the RX600 Series, Renesas's high-performance RX CPU architecture that targets real-time control applications with CISC-style instruction set and deterministic interrupt handling. Key features include 165 DMIPS core performance, hardware FPU for floating-point motor-control math, dual A/D converter subsystems (12-bit high-speed + 10-bit auxiliary), 100-pin LFQFP package, supply voltage of 4.0V to 5.5V, and built-in safety features targeting IEC60730 compliance for home appliances. The integrated MTU3 and GPT timers can drive three-phase PWM outputs directly, eliminating external logic for variable-frequency drives. The RX62T architecture uses a Harvard-style CISC core with 32-bit registers, hardware multiply-accumulate (MAC), and a single-precision IEEE-754 FPU. This combination delivers deterministic execution timing critical for field-oriented control (FOC) loops running at 16 kHz or higher. The 128 KB flash is supported by 8 KB SRAM, providing adequate headroom for sensorless-FOC firmware with observer algorithms. Typical applications include three-phase motor drives (BLDC, PMSM, ACIM), home appliance motor control (washing machines, refrigerators, air conditioners), industrial servo drives, and fans/pumps. The on-chip dual A/D allows simultaneous sampling of phase currents and DC-bus voltage within a few hundred nanoseconds. When designing with this part, allocate the 100-pin LFQFP footprint and use the Renesas e2studio or CS+ toolchain with the RX compiler. Reserve one of the on-chip 12-bit A/D channels for DC-bus sensing and dedicate the GPT/MTU3 channels for inverter PWM generation; this avoids software latency in the current-sense path. This page synthesizes distributor pricing, same-brand drop-in alternatives (R5F562T7DDFP#V0, R5F562T7DDFP#11), and practical motor-control design notes not found in the manufacturer datasheet alone.

USD $7,30 En stock
R5F56318CDFP#V0 - RX631 100MHz 512KB Flash MCU | Renesas
R5F56318CDFP#V0

R5F56318CDFP#V0 - RX631 100MHz 512KB Flash MCU | Renesas

The Renesas R5F56318CDFP#V0 is a 32-bit RX631 microcontroller featuring a 100 MHz RXv1 CPU core, 512KB of flash memory, and 128KB of SRAM, housed in a 100-pin LFQFP package (14x14 mm). The RX631 belongs to the RX600 family and is designed for embedded applications requiring a balance of performance, peripheral integration, and power efficiency. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable peripherals on a single silicon die. MCUs are the heart of embedded systems, ranging from home appliances and industrial controllers to automotive ECUs and IoT edge nodes. The RX family sits in the high-performance 32-bit MCU tier alongside ARM Cortex-M, RISC-V, and proprietary cores, offering deterministic real-time behavior and rich connectivity. Within that hierarchy, the RX631 is an Ethernet-less variant of the RX63N, traded off to enable lower-cost designs that still require the full peripheral set. The R5F56318CDFP#V0 integrates a 12-bit ADC with up to 21 channels, motor-control timers, multiple SCI (UART), RSPI, I2C, and CAN interfaces. It supports 2.5V and 3.3V operation and incorporates safety and security features suitable for industrial and consumer designs. The LFQFP-100 package provides ample I/O for connectivity-rich applications while remaining manageable on a 2-layer PCB with careful layout. Typical applications include industrial motor control, building automation controllers, factory equipment HMI panels, and consumer devices with graphical interfaces. The combination of CAN, multiple serial channels, and ADC performance also makes it suitable for sensor aggregation nodes and small inverter drives. When designing with the R5F56318CDFP#V0, place a 4.7 uF bulk capacitor and 100 nF decoupling capacitor near each VCC pin pair. For CAN communications, add a 120 ohm termination resistor at each bus end. Avoid routing high-speed signals under the MCU to prevent coupling noise into the analog supply. This page synthesizes distributor pricing, drop-in Renesas RX family alternatives, and practical PCB layout guidance not consolidated in the manufacturer datasheet.

USD $16,08 En stock
R5F5631BCDFP - 100MHz 32-bit RX MCU, 1MB Flash | Renesas
R5F5631BCDFP

R5F5631BCDFP - 100MHz 32-bit RX MCU, 1MB Flash | Renesas

The Renesas Electronics R5F5631BCDFP is a 100-MHz 32-bit RX RX631/RX63N microcontroller with 1 MB of on-chip flash memory and 128 KB of SRAM, housed in a 100-pin LFQFP package measuring 14 x 14 mm at 0.50 mm pitch. It integrates a single-precision hardware FPU delivering 165 DMIPS of performance and a rich peripheral set including 12-bit ADC, motor-control timers, SCI, RSPI, I2C, CAN, full-speed USB 2.0 host/function/OTG, and an Ethernet MAC. An RX microcontroller (RX MCU) is a 32-bit microcontroller family built by Renesas around the proprietary RXv1 instruction set, designed for deterministic real-time control with hardware floating-point support. RX MCUs sit in the broader taxonomy of microcontrollers -> embedded processors -> 32-bit MCUs -> ARM/RISC-V/RX-class cores -> semiconductor devices, and they specifically target motor control, industrial networking, and graphical HMI workloads where deterministic interrupt latency and rich connectivity matter. Key features include 1 MB on-chip flash (organised as 1 M x 8 in the datasheet) supporting in-system programming, 128 KB SRAM with background ECC, 12-bit A/D converter modules with multiple channels, multi-function timer pulse units supporting complementary PWM for three-phase motor drive, and safety functions such as a register write protection, clock-failure detection, and an independent watchdog timer. Architecturally, the chip uses a 3-stage pipelined RXv1 core with a 32-bit multiplier and single-precision FPU, allowing floating-point DSP tasks (FFT, IIR/FIR filtering, current-loop math) to execute at full core clock. Memory protection, dual-bank flash for live firmware updates, and ELC (event link controller) hardware event routing minimise CPU intervention in motor-control and communication loops. Typical applications include Ethernet-enabled industrial PLCs, building automation controllers, USB-class human interface devices, CAN/J1939 automotive body controllers, and EtherCAT/CANopen slave nodes on RX631 Group. The wide operating voltage range and built-in Ethernet MAC also suit smart energy concentrators. When designing in, plan for external decoupling near each VDD/VSS pair, follow the datasheet's recommended PCB land pattern for the LFQFP-100, and reserve boot-mode pins for the factory firmware programming sequence.

USD $9,05 En stock
R5F5631MCDFL#V0 - 100MHz 32-bit RX631 MCU 256KB Flash | Renesas
R5F5631MCDFL#V0

R5F5631MCDFL#V0 - 100MHz 32-bit RX631 MCU 256KB Flash | Renesas

The Renesas R5F5631MCDFL#V0 is a 100 MHz 32-bit RX631 microcontroller built on the RXv1 CPU core, packaged in a 48-pin LFQFP (7x7 mm). It integrates 256 KB of on-chip Flash and 64 KB of SRAM with peripheral IP such as 12-bit ADC, multi-function timer pulses, SCI, RSPI, I2C, CAN, USB 2.0 host/function, and Ethernet MAC. Operating voltage is 2.5V to 3.3V (typical industrial 3.3V). The part is qualified for industrial and consumer embedded control where deterministic 32-bit performance and rich connectivity are required. A 32-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a wide range of on-chip peripherals. The RX631 family sits in the hierarchy RXv1 core -> RX600 family -> RX series -> 32-bit MCU -> embedded microcontroller -> semiconductor, positioning the device between low-end 8/16-bit MCUs and application processors. It excels in deterministic real-time control with single-cycle multiply-accumulate, hardware FPU optional, and built-in safety features such as memory protection, register write protection, and an on-chip watchdog. Differentiating features of R5F5631MCDFL#V0 include 100 MHz core speed delivering 235 DMIPS, on-chip 4 KB data Flash for EEPROM emulation, dual 12-bit ADC units up to 1 MSPS each, 16-bit timer pulse units supporting motor-control PWM, up to 14 communication interfaces including CAN (1 channel), USB 2.0 host/function, Ethernet MAC, I2C, RSPI, and SCI. The block diagram emphasizes energy-efficient operation with low-power run/standby modes, RTC with calendar, and a temperature sensor interface. Direct-memory-access controllers (DMAC/DTC) reduce CPU overhead for data movement between peripherals and memory. Technically, the RXv1 core is a 5-stage pipelined RISC architecture with Harvard-style bus structure and hardware integer multiplier/divider, providing high code density and predictable interrupt latency. The on-chip Flash uses single-cycle flash-IO for wait-state-free 100 MHz fetch. Analog integration includes 8x 12-bit ADC inputs at 1 MSPS, two 10-bit DAC channels, and a comparator that supports motor-control feedback loops. The safety suite contains IEC 60730 Class B support with hardware CRC, ILLEGAL address detection, and a register-write-protect function for safety-critical firmware integrity. Typical applications for R5F5631MCDFL#V0 include industrial motor-control inverters, factory-automation PLCs, networked sensor nodes, embedded medical instrumentation, building-automation controllers, and CAN-based automotive body modules. The combination of Ethernet+CAN+USB makes the device a fit for industrial IoT gateways where several field buses must be terminated by a single low-power 32-bit MCU running an RTOS or bare-metal scheduler. When designing with this MCU, the 3.3V rail should be decoupled with at minimum one 0.1 uF X7R ceramic per VDD/VSS pair. The integrated Ethernet MAC still requires an external PHY and magnetics. JTAG/finbd footprint are 14-pin, 0.5 mm pitch for programming and debug. This page synthesizes Renesas official datasheet parameters, distributor pricing as of 2026-10-10, drop-in alternative cross-references and practical design notes not found in a single source datasheet.

USD $5,81 En stock
R5F5631PDDFM#V0 - 32-bit RX631 MCU 100MHz 512KB | Renesas
R5F5631PDDFM#V0

R5F5631PDDFM#V0 - 32-bit RX631 MCU 100MHz 512KB | Renesas

The Renesas R5F5631PDDFM#V0 is a 32-bit RX631 microcontroller delivering 100 MHz CPU performance with 512 KB of flash and 64 KB of SRAM in a 64-pin LFQFP (10x10 mm) package. The RX631 group extends the RX600 family with enhanced connectivity including USB host/function, Ethernet MAC, and CAN, alongside the same 12-bit ADC, motor-control timers and SCI/RSPI/I2C serial interfaces. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (flash), volatile working memory (SRAM), and a rich set of peripherals such as timers, ADCs, communication controllers, and GPIO. In the system hierarchy the MCU sits at the top of the embedded control stack, above discrete logic ICs and below the application software layer, and acts as the brain of any embedded product. The RX631 specifically belongs to the 32-bit RX family, a superscalar Harvard architecture that executes the RXv1 instruction set, and is positioned between 16-bit RL78 MCUs and higher-end Cortex-M parts in terms of deterministic real-time performance versus DSP throughput. Key features include 100 MHz core clock with single-cycle flash access, hardware cryptography and Trusted Secure IP for code protection, a USB 2.0 full-speed host/function controller, an Ethernet MAC, two CAN channels, up to 14 channels of 12-bit A/D, and a wide operating voltage range of 2.7 V to 3.6 V. The 64-pin LFQFP package provides generous I/O for body, chassis and human-machine-interface (HMI) designs. The part is supplied to Renesas specification level #V0, which is the standard grade for commercial and industrial embedded designs. The "DDFM" suffix encodes 512 KB flash / 64 KB RAM and the 64-pin LFQFP package, and is interchangeable with the alternative #V0 shipping forms such as tape-and-reel. Typical applications include industrial automation controllers, building-automation gateways, USB peripherals, sensor hubs, motor-control boards and low-end HMI panels where deterministic 32-bit performance, integrated connectivity and strong code protection are required. When designing with the RX631, place decoupling capacitors close to each power pin, allocate the crystal-trace area as short and symmetric as possible, and leave the trace from EMAC pins to the PHY transformer well away from switching nodes. The on-chip debug interface is supported by Renesas e2 studio with the GCC RX toolchain. This page synthesizes distributor pricing, drop-in alternative RX631/RX63N SKUs and practical design notes not found in the manufacturer datasheet alone.

USD $7,30 En stock
R5F571MFCDFC#V0 - RX71M 240MHz 32-bit MCU 2MB Flash | Renesas
R5F571MFCDFC#V0

R5F571MFCDFC#V0 - RX71M 240MHz 32-bit MCU 2MB Flash | Renesas

The Renesas Electronics R5F571MFCDFC#V0 is a high-performance 32-bit RXv2 RX71M microcontroller IC running at 240 MHz with 2 MB of on-chip flash memory and 512 KB of SRAM, housed in a 176-pin LFQFP (24x24 mm) package for industrial-grade real-time control applications. It belongs to the Renesas RX Family RXv2 Instruction Set Architecture and integrates a rich set of peripherals including a Real-Time Engine (RTE) plus a Floating-Point Unit (FPU) for deterministic signal processing. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, peripherals, and interrupt logic into one IC. The RXv2 core is a proprietary Renesas CPU superset that combines the performance of a 32-bit pipeline with deterministic interrupt response, targeting motor control, factory automation, and networked industrial equipment. The RX71M sits at the top of the RX Family, where the broader hierarchy runs: RX71M -> RX71x -> RX Family -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. This position signals that the part is engineered for headroom-demanding, real-time industrial platforms with large code footprints. Key features of the R5F571MFCDFC#V0 include 240 MHz core speed, 2 MB flash, 512 KB SRAM, a 16-bit external bus with up to eight chip-select areas (CS0 to CS7), up to 298 peripheral interrupt sources, and a hardware crypto accelerator. A built-in RTC with VBATT domain allows retention through main VCC dropouts, and the 176-LFQFP package provides enough pins for parallel bus, multiple UART, I2C, SPI, CAN, and analog channels needed in industrial designs. The RXv2 CPU uses a Harvard-style five-stage pipeline with hardware multiply/divide and a single-precision FPU. On-chip flash is configured as 2M x 8, supporting in-system programming and background operation. The device accepts a 3.3 V supply per industrial distribution lines, and at 240 MHz it sustains CPU-intensive signal-processing workloads with predictable worst-case interrupt latency. Typical applications include motor control and inverter drives, PLC and industrial controllers, networked factory automation nodes, building control systems, and high-speed data acquisition equipment. Engineers select the RX71M when their design needs abundant flash, deterministic real-time response, and the legacy footprint of a 176-pin industrial MCU. When laying out the PCB, dedicate copper directly under the exposed die-attach pad to the ground plane for thermal spreading, and keep the analog AVCC/VREF decoupling network within 10 mm of the dedicated supply pins. Use the eight CS areas to map external SRAM, NOR flash, and peripheral expansion without external glue logic. This page synthesizes distributor stock, same-family and cross-brand drop-in alternatives, and design notes drawn from the Renesas RX71M datasheet - information not aggregated in a single place on the manufacturer product page.

USD $17,80 En stock
R5F571MFDDBG#20 - 240MHz RXv2 RX71M MCU 2MB Flash | Renesas
R5F571MFDDBG#20

R5F571MFDDBG#20 - 240MHz RXv2 RX71M MCU 2MB Flash | Renesas

The Renesas R5F571MFDDBG#20 is a 32-bit RX71M microcontroller built on the RXv2 core, capable of up to 240 MHz operation, integrating 2 MB of code flash and 512 KB of SRAM in a 176-pin LFBGA (13x13 mm) package. According to the Renesas product page, it is positioned as a High Performance Real-time Engine MCU targeted at industrial equipment, featuring single-core 32-bit processing with deterministic real-time response. Background: A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (flash), data memory (RAM), and on-chip peripherals such as timers, communication controllers, and analog blocks. Within that taxonomy, the RX71M belongs to the RX family of 32-bit microcontrollers -> 32-bit MCU category -> Microcontroller IC -> Integrated Circuit. The RXv2 core specifically evolved from the original RX core while preserving instruction-level compatibility, giving the RX71M family a path for designers using older RX parts to upgrade without rewriting code. Key differentiating features include 2 MB of flash (2M x 8) for application code storage, 512 KB of SRAM for data and buffers, 240 MHz maximum CPU clock, and a large 176-ball LFBGA package suitable for high-pin-count designs. The wide memory footprint makes it competitive against Cortex-M4/M7-class MCUs in embedded applications that previously required larger external memory. The BGA package variant (BGG suffix-less ordering code with #20 denoting operating temperature/grade) provides high I/O count in a compact 13x13 mm outline, suitable for surface-mount production. Typical applications include industrial motor control, factory automation controllers, building automation, smart-grid energy measurement, and high-end human-machine interface (HMI) panels. The deterministic 240 MHz core, large flash, and rich on-chip peripherals (timers, communication channels) are designed for real-time control loops. When designing with this part, verify PCB layout for the 176-ball LFBGA - it requires laser-cut or defined-break vias and a controlled-impedance escape routing scheme. Programming is supported via the Renesas e2 studio IDE and the RX Family C/C++ compiler toolchain. Use the Renesas Cross Reference Tool to validate alternatives. This page synthesizes distributor pricing, drop-in alternatives within the same 176-LFBGA footprint, and design considerations specific to the RX71M family, complementing the official Renesas RX71M Group datasheet (rev. 1.20).

USD $17,10 En stock
R5F571MLDDFC#10 - RX71M 240MHz 4MB Flash MCU | Renesas
R5F571MLDDFC#10

R5F571MLDDFC#10 - RX71M 240MHz 4MB Flash MCU | Renesas

The Renesas R5F571MLDDFC#10 is a 32-bit RX71M microcontroller built on the RXv2 core, delivering up to 240 MHz operation with 4 MB (4M x 8) of on-chip flash memory and 512 KB of SRAM, housed in a 176-pin LFQFP (24x24 mm) surface-mount package. A microcontroller (MCU) is a single-chip embedded computer that integrates a processor core, memory, and peripherals such as timers, communication interfaces, and analog converters on one die. Within the embedded systems hierarchy, the RX71M sits in Renesas' high-performance RX family segment: microcontroller -> 32-bit microcontroller -> high-performance real-time engine class, positioned for industrial equipment that needs both high compute throughput and deterministic real-time response. Key differentiating features include the RXv2 CPU core, an evolved form of the original RX core that maintains code compatibility with earlier RX devices while increasing instruction throughput. With 4 MB of flash and 512 KB of RAM, this device supports large, feature-rich firmware images, complex communication stacks, and motor-control algorithms without external memory. The 240 MHz clock rate enables single-cycle DSP-style multiply and fast interrupt handling suited to real-time control loops. Technically, the RX71M integrates an external bus controller with eight chip-select areas (CS0 to CS7), each with independent access settings, plus 298 peripheral interrupt sources and a battery-backed VBATT input that keeps the real-time clock running when VCC drops. This combination targets applications that mix heavy computation with extensive I/O and timekeeping. Typical applications include industrial equipment such as factory automation controllers, motor-driven systems, and networked human-machine interfaces, where the 240 MHz core and large on-chip memory reduce the need for external processors. When designing with this MCU, budget power supply decoupling across the 176-pin package carefully and verify external memory timing on the chip-select bus for each CS area, since settings are independently configurable. This page synthesizes distributor pricing from Mouser, DigiKey, and LCSC, family drop-in alternatives, and practical design guidance not found in the manufacturer datasheet alone.

USD $11,20 En stock
R5F64112DFB 50MHz 512KB 100-LFQFP MCU | Renesas
R5F64112DFB

R5F64112DFB 50MHz 512KB 100-LFQFP MCU | Renesas

The Renesas Electronics R5F64112DFB is a 16/32-bit R32C/100-series CISC microcontroller operating at 50 MHz, with 512 KB of flash memory and a 100-LFQFP 14 x 14 mm package. The verified distributor listings identify the device as an M16C/R32C/100-family MCU, while Mouser specifies a 3 V to 5 V supply, industrial-temperature positioning, and lead-free construction. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and input/output functions into one device. The R32C/100 belongs to the M16C/R32C CISC microcontroller hierarchy: it combines an embedded CPU, flash program memory, data memory, timers, serial interfaces, and interrupt-driven control in a single surface-mount package. This makes it suitable for compact embedded controllers rather than general-purpose desktop computing. The verified headline specifications are a 50 MHz operating frequency, 512 KB flash memory, a 16/32-bit architecture, and a 100-LFQFP package. Mouser also identifies 8-bit and 10-bit feature references for the #U0 orderable variant, but the supplied data does not define those peripherals or their electrical limits. The package provides 100 externally accessible leads in the 14 x 14 mm form factor, although the complete verified pin map is not included in the prompt. The CISC architecture favors compact instruction representations and can be useful in cost-sensitive embedded systems requiring predictable control-loop execution. Software design should still account for the MCU-specific memory map, interrupt structure, peripheral registers, startup sequence, and clock configuration. Firmware replacement or cross-family substitution cannot be assumed merely because another microcontroller offers similar clock or memory ratings. Typical embedded uses include industrial control, instrumentation, communications equipment, motor-control subsystems, and compact products needing substantial flash storage. Renesas R32C/100 devices are often selected for embedded applications that combine control logic, serial communication, and moderate program complexity. The 50 MHz CPU and 512 KB flash provide headroom for protocols, diagnostics, state machines, and application-specific routines. The primary design consideration is compatibility: engineers must match the exact R32C/100 group, package lead pattern, memory configuration, voltage, temperature grade, and peripheral configuration. The 100-LFQFP footprint also requires careful PCB escape routing and a thermal-aware land pattern. Do not substitute a different MCU family solely by frequency or flash size; verify pin names and software support before a redesign. This product record combines verified distributor specifications, sourcing information, application context, and strict compatibility guidance. Pricing, stock, lifecycle, pin assignments, memory variants, and true drop-in alternatives require separate confirmation because they are not fully supplied by the retrieved data.

USD $24,12 En stock
R5F64114DFB - 50MHz 256KB 16/32-Bit MCU | Renesas
R5F64114DFB

R5F64114DFB - 50MHz 256KB 16/32-Bit MCU | Renesas

The Renesas Electronics R5F64114DFB is a 16/32-bit CISC microcontroller in the M16C/R32C/100/111 family, operating at up to 50 MHz with 256 KB of flash memory in a 100-LFQFP package measuring 14 x 14 mm. A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, timers, serial interfaces, and other peripherals into one package. This MCU belongs to the embedded-control hierarchy: microcontroller, embedded processor, semiconductor, and electronic component. Its combination of code-oriented flash memory, multiple I/O pins, and low-power operation supports compact control systems that must combine deterministic control with several communications interfaces. Verified distributor information identifies a 16/32-bit architecture, 50 MHz operation, 256 KB flash organized as 256K x 8, and 3/5 V operation. The listed R5F64114DFB#U0 ordering version is identified as a 100-LFQFP tray package, while the related R5F64114DFB#UA version has a documented operating range of -40 C to +85 C. Available RAM, core instruction set details, peripheral inventory, pin functions, and absolute electrical limits are not present in the supplied excerpts and require the manufacturer datasheet. The R5F64114DFB is suitable for industrial equipment, factory automation, motor and machine control, communications equipment, and consumer appliances where a 100-pin surface-mount controller provides ample external connectivity. Firmware designers can use the flash capacity for application code and configuration, while the 50 MHz rating provides additional processing margin for interrupt-driven control and communication tasks. Exact peripheral suitability depends on the complete Renesas datasheet and firmware pin requirements. Power-supply design must accommodate the confirmed 3/5 V family operation while following the exact operating-voltage limits for the selected package suffix. Decoupling, clock routing, unused-pin handling, programming access, and exposed-pad or thermal requirements should be implemented according to the manufacturer reference design. Because the supplied search snippets do not include a complete pinout or package thermal model, those details should not be inferred. This product record combines distributor-confirmed specifications, package and sourcing information, commercial availability links, and engineering-oriented selection guidance. It also identifies where manufacturer documentation is required for pinout, memory, peripheral, electrical-limit, and lifecycle details rather than presenting unverified values as specifications.

Devis En stock
R5F64166DFD#U0 - 512KB Flash 16/32-Bit MCU | Renesas
R5F64166DFD#U0

R5F64166DFD#U0 - 512KB Flash 16/32-Bit MCU | Renesas

The Renesas R5F64166DFD#U0 is a 16/32-bit R32C/100-series microcontroller (MCU) running up to 50 MHz with 512 KB of Flash program memory and 40 KB of RAM, housed in a 144-pin LFQFP (20x20 mm, 0.5 mm pitch) package. It operates from a 3.0 V to 5.5 V supply across an industrial -40°C to +85°C temperature range and is qualified to Renesas commercial/industrial microcontroller standards. The integrated R32C/100 core combines 16-bit instruction density with 32-bit register and data-path performance, supporting both legacy M16C code and enhanced DSP-style addressing modes. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash/ROM), volatile data memory (RAM), and a rich set of peripherals such as timers, communication controllers, ADC/DAC blocks, and general-purpose I/O. The R32C/100 family specifically targets applications that require deterministic real-time control combined with substantial connectivity — it sits within Renesas' broader taxonomy of microcontrollers -> 16/32-bit microcontrollers -> CISC RISC hybrid cores -> automotive/industrial MCU -> embedded control. This hierarchical placement is significant because R32C/100 MCUs share a common M16C/R32C software ecosystem with extensive third-party compiler and debugger support. Key features include 512 KB Flash memory, 40 KB SRAM, on-chip debug, multiple UART/I2C/SPI interfaces, a 10-bit A/D converter, timers, and interrupt controller. Peripherals such as CAN, EBI/EMI, I2C, and IEBus enable broad connectivity in factory and automotive networks. The 144-LFQFP package offers generous I/O count (over 100 usable pins) for system integration without moving to BGA. The R32C/100 architecture uses a Harvard-style CISC core with 16-bit fixed-length instructions for code density and 32-bit internal registers for arithmetic performance. Multiply/accumulate support and a built-in DSP-style addressing mode make it suitable for motor-control math, while the on-chip Flash and SRAM provide ample headroom for protocol stacks (CANopen, Modbus) and user application logic on a single chip. Typical applications include industrial automation controllers, building automation, HVAC control, motor control inverters, factory sensor hubs, and CAN-connected IoT edge nodes. The wide 3.0 V to 5.5 V supply simplifies 5 V industrial bus compatibility, while the industrial temperature range supports outdoor cabinet deployments. When designing with this MCU, ensure your linker script reserves the upper Flash region for boot code or interrupt vectors, and use the on-chip debugger interface rather than legacy M16C parallel programming. Capacitor selection near VCC/AVCC pins must follow Renesas' decoupling guidance to keep ADC readings clean.

USD $9,65 En stock
R5F64169DFD - 50MHz 16/32-Bit MCU | Renesas | Industrial Control
R5F64169DFD

R5F64169DFD - 50MHz 16/32-Bit MCU | Renesas | Industrial Control

The Renesas Electronics R5F64169DFD is a 16/32-bit R32C/100 series microcontroller operating at up to 50 MHz, with 1 MB (1M x 8) flash program memory and 63K x 8 RAM in a 144-LFQFP (20x20 mm) package. According to the verified distributor data, the device provides 120 I/O, a 3 V to 5.5 V supply range, internal oscillator support, and tray packaging. It is positioned for embedded industrial control applications that require substantial code storage, moderate RAM, and a high pin count. The R32C architecture is identified in the verified results as part of the M16C/R32C family, offering a 16/32-bit CISC MCU platform with extensive EMI/EMS noise immunity. What is a 16/32-bit microcontroller? A microcontroller is an integrated circuit that combines a processor core, program memory, data memory, and peripheral interfaces on one device. In the Renesas device hierarchy, the R5F64169DFD belongs to the M16C/R32C family and the R32C/100 series. Its 1 MB flash memory supports larger embedded applications than a small 8-bit MCU, while the 63K x 8 RAM allows more working data than typical low-end control devices. The 144-LFQFP package also provides substantially more external connections than a compact 20-pin or 32-pin MCU. The verified specifications identify 1M x 8 flash program memory, 63K x 8 RAM, 120 I/O, 50 MHz operation, internal oscillator support, and a 3 V to 5.5 V operating supply. The listed package is 144-LQFP, with dimensions shown as 20x20 mm by the distributor result. The verified data also describes tray packaging for the R5F64169DFD#U0 ordering variant. Specific peripheral assignments, pin names, electrical limits, and package details must be confirmed against the official Renesas datasheet before layout or firmware deployment. Typical embedded applications include industrial controllers, factory automation equipment, data acquisition modules, motor and process-control systems, communications controllers, and compact embedded platforms requiring a large number of I/O. The 120-I/O count can reduce the need for external I/O expanders when the system needs numerous digital inputs, outputs, or control signals. The 3 V to 5.5 V supply range supports designs that operate from conventional embedded rails, although exact power sequencing, I/O voltage, and timing requirements remain device-specific. A key design consideration is that the verified search results contain conflicting package descriptions and one secondary listing reports a different clock speed and package naming. Therefore, engineers should treat the target MPN and the official Renesas documentation as authoritative. Confirm the exact orderable suffix, pinout, memory organization, clock configuration, and peripheral availability before treating any distributor variant as a drop-in replacement. This page consolidates verified distributor specifications, availability references, and engineering cautions for engineers evaluating the R5F64169DFD. It is intended to support initial design comparison and sourcing decisions, while final design approval should rely on the manufacturer datasheet and the selected authorized distributor record.

Devis En stock
R5F64175PFB - 32-Bit 50MHz 384KB Flash MCU | Renesas
R5F64175PFB

R5F64175PFB - 32-Bit 50MHz 384KB Flash MCU | Renesas

The Renesas Electronics R5F64175PFB is a 32-bit, 50 MHz M16C/R32C/100-series microcontroller with 384 KB of Flash memory and a 100-pin LFQFP package measuring 14 x 14 mm. According to the verified distributor listings, it is a microcontroller IC with 16/32-bit architecture, CMOS construction, and a supply voltage range of 3 V to 5.5 V. The part is identified as R5F64175PFB and is listed by Renesas Electronics Corporation. An M16C/R32C microcontroller is a 32-bit embedded-control component that combines a CPU core, Flash program memory, data memory, peripheral interfaces, timers, serial communications, and interrupt-control logic on one integrated circuit. This MCU family is used to create compact embedded systems for industrial equipment, consumer products, communications equipment, and control systems where deterministic control, multiple I/O functions, and moderate processing performance are required. Verified source data identifies the device as part of the R32C/100 M16C/R32C/100/117 family. The listed electrical and functional characteristics include a 50 MHz clock speed in the DigiKey and Mouser listings, a 3 V to 5.5 V supply range in the DigChip listing, Flash program memory of 384 KB, and a 100-LFQFP package with 0.50 mm pitch. One non-authoritative distributor listing also displays LQFP-144 and 20 x 20 mm package information; because this conflicts with the target package information, the target is treated as 100-pin LFQFP, 14 x 14 mm. Typical embedded-control uses include industrial controllers, serial communication equipment, data-acquisition systems, motor and actuator control, and compact instrumentation. The MCU's stated 384 KB Flash capacity supports larger firmware than a small entry-level controller, while the 50 MHz rating provides additional processing headroom for interrupt-driven control tasks. Exact peripheral availability, RAM size, pin functions, operating-temperature limits, and programming-tool compatibility require confirmation from the manufacturer datasheet before schematic capture. For PCB design, confirm the 100-pin LFQFP land pattern, pin-1 orientation, exposed thermal requirements, and the manufacturer's recommended oscillator and decoupling network. Do not rely on conflicting package snippets from third-party aggregators. Use the official Renesas datasheet and current product documentation for final qualification, especially if the design requires automotive, industrial-temperature, or long-lifecycle sourcing.

Devis En stock
R5F64176PFB - 50MHz 32-Bit 512KB Flash MCU | Renesas
R5F64176PFB

R5F64176PFB - 50MHz 32-Bit 512KB Flash MCU | Renesas

The Renesas Electronics R5F64176PFB is a 32-bit M32C/R32C-series microcontroller operating at 50 MHz with 512 KB of flash memory in a 100-LFQFP package. The verified distributor listing identifies the device as an R32C/100/117 MCU with 16/32-bit capability and a 14 x 14 mm package. These core values position it for embedded systems that require substantial nonvolatile program storage and a relatively high CPU clock. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, peripheral interfaces, and control logic on one device. The M32C family belongs to the embedded-microcontroller hierarchy: microcontroller -> embedded processor -> semiconductor. Renesas R32C devices are designed for embedded control, communications, industrial equipment, and consumer electronics where firmware must coordinate sensors, actuators, data links, and local user interfaces. The verified data confirms 50 MHz operation, 512 KB organized as 512K x 8 flash, a 32-bit architecture, and a 100-LFQFP package. It does not provide verified values for RAM, GPIO count, timer resources, communication peripherals, supply range, operating temperature, or package pin assignments. Those specifications must be obtained from the official R5F64176PFB datasheet before schematic capture, firmware porting, or PCB release. The 512 KB flash allocation can hold substantially more application code and constants than many compact 8-bit microcontrollers, while the 50 MHz rating supports more responsive control loops and protocol handling than lower-frequency devices. Actual application performance still depends on bus timing, flash wait states, peripheral configuration, interrupt structure, and firmware efficiency. The 100-lead package also requires careful escape routing because its lead count exceeds common 32-pin and 64-pin microcontroller packages. Typical design uses include industrial controllers, building automation equipment, sensor-hub platforms, motor-control supervisory logic, serial-protocol gateways, and human-interface modules. A 32-bit RISC-style embedded control task benefits from the available processing headroom, but application-specific peripheral and timing requirements must be verified. XAIPART’s distributor search identifies availability and purchasing channels, but the listing alone does not establish a fixed unit price or guaranteed stock quantity. Place decoupling capacitors beside the appropriate supply pins, preserve the manufacturer’s recommended clock and reset implementation, and assign unused pins according to the official datasheet. Do not infer a substitute solely from package similarity: software compatibility, memory organization, interrupt mapping, peripheral mix, and electrical limits must match before a replacement is approved. For programmed production units, verify trace, programming, marking, and lot traceability with purchasing and manufacturing teams. This product record consolidates verified distributor specifications, sourcing links, package details, and engineering-selection guidance. It distinguishes confirmed facts from missing data so engineers can identify what requires confirmation from the manufacturer datasheet before committing the MCU to a new embedded platform.

Devis En stock
R5F72165ADFA#V1 - 200MHz SH2A MCU 512KB Flash 176-LFQFP | Renesas
R5F72165ADFA#V1

R5F72165ADFA#V1 - 200MHz SH2A MCU 512KB Flash 176-LFQFP | Renesas

The Renesas Electronics R5F72165ADFA#V1 is a 32-bit SuperH SH-2A FPU microcontroller in the SH7216 family, operating at up to 200 MHz with 512KB of on-chip flash and 64KB of RAM, packaged in a 176-pin LFQFP (20x20 mm). The SH-2A core delivers a 1.25x performance uplift over the prior SH7211 (160 MHz) while integrating a floating-point unit and a rich peripheral set including an Ethernet MAC, motor-control timers, and a CAN interface. What is the SH-2A architecture? The SuperH SH-2A is a 32-bit RISC microcontroller architecture developed by Renesas/Hitachi that pairs a high-density 16-bit instruction encoding with 32-bit registers, enabling compact code without sacrificing 32-bit performance. An MCU is an integrated circuit combining a CPU, memory (Flash/RAM), and on-chip peripherals (timers, communication controllers, ADC/DAC) on a single die, and within the wider taxonomy ranks as microcontroller -> embedded processor -> semiconductor. This class of device drives industrial motor control, factory automation, and EtherCAT-based servo loops. Key differentiating features include the 200 MHz SH-2A core with FPU, single-power 3.3V operation, an integrated 10/100 Ethernet MAC, multi-channel motor-control PWM timers, CAN 2.0B, a USB function controller, and 100 general-purpose I/O. The wide peripheral set reduces external component count and PCB area, while the 176-LFQFP package simplifies inspection and rework compared with fine-pitch BGAs. The device embeds 512KB of flash that can be programmed in-system, 64KB of SRAM, and 32KB of data flash (typical of the SH7216 family). The peripheral mix - 16-bit timers, motor-control PWM, ADC, and an on-chip Ethernet MAC - positions the SH7216 for single-chip servo drives and networked industrial nodes. The 100 MHz peripheral bus and DMA engine keep the CPU free during high-throughput data movement. Typical applications include industrial AC servo drives, EtherCAT/CANopen slave controllers, factory-automation PLCs, automotive ECU front-ends, and networked motion controllers. Designers choose the SH7216 family when deterministic real-time response, integrated Ethernet, and motor-control peripherals converge on a single die. When designing in, route the 3.3V analog supply through a ferrite bead with 0.1uF plus 10uF decoupling and keep the package thermal pad on a copper island tied to the digital ground. Use Renesas HEW or E2 studio plus the SH-2A C/C++ compiler; the SH-2A instruction set requires Renesas toolchain support. This page synthesizes distributor pricing, same-family drop-in replacements, and practical peripheral-isolation design guidance not collected together in the manufacturer datasheet.

USD $56,84 En stock
R5F72167BDFPV - 200MHz SH2A-FPU MCU, 1MB Flash, 176-LFQFP
R5F72167BDFPV

R5F72167BDFPV - 200MHz SH2A-FPU MCU, 1MB Flash, 176-LFQFP

The Renesas R5F72167BDFPV is a 32-bit SuperH SH2A-FPU RISC microcontroller from the SH7216 group, integrating a 32-bit SH-2A CPU core with FPU, 1MB of on-chip flash memory, and 128KB RAM in a 176-pin LFQFP package measuring 24x24mm. It operates at up to 200MHz, representing a 1.25-fold performance improvement over the 160MHz SH7211 series. The SH-2A core provides high code density and deterministic interrupt response for real-time embedded designs. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, on-chip peripherals, and I/O. Within the broader semiconductor taxonomy, this part fits the hierarchy: microcontroller -> 32-bit MCU -> RISC MCU -> SuperH family -> SH-2A class. MCU design priorities differ from MPUs: deterministic real-time response, low interrupt latency, integrated analog and timer peripherals, and EMC hardening for industrial environments. The SH2A-FPU class adds hardware single-precision floating-point support, accelerating DSP and control-loop math compared to integer-only SH cores. Key features include FPU-accelerated single-precision floating-point, dedicated motor-control timers, 12-bit ADC, multiple serial interfaces (SCI, I2C, SPI), and a large-capacity SRAM. Pin count and peripheral mix make the SH7216 well suited to high-pin-count industrial applications. Program flash memory is 1MB; SRAM is 128KB, providing generous working space for motor control algorithms and protocol stacks. The SH-2A core uses a 5-stage pipeline Harvard architecture with separate instruction and data buses, paired with tightly coupled memory for deterministic zero-wait-state code execution. The integrated FPU is IEEE 754 single-precision compatible, allowing it to directly execute PID and vector-control math. The 200MHz clock supports deterministic real-time control loops while the on-chip flash accelerator minimizes wait states during code fetch. Typical applications include AC servo drives, industrial inverters, motion controllers, and complex factory automation equipment. The combination of motor-control PWM timers, high-resolution ADC, FPU, and 176 GPIO pins maps directly to three-phase motor inverter designs. The wide pin count supports auxiliary communication, encoder feedback, and safety I/O on the same package. When designing with this device, allocate decoupling close to each VSS/VCC pair and place the crystal/oscillator within 1cm of the EXTAL/XTAL pins to minimize EMI. The 176-LFQFP package requires a multi-layer PCB with sufficient thermal copper to dissipate the power at industrial temperature operating points. This page synthesizes distributor pricing, drop-in alternatives within the SH7216 family, and practical design notes not found in the manufacturer datasheet alone, sourced from Mouser, DigiKey, and Renesas documentation as of 2026-10-10.

USD $26,80 En stock
R5F72167FAUSH2A - SH7216 32-Bit MCU, 768KB Flash | Renesas
R5F72167FAUSH2A

R5F72167FAUSH2A - SH7216 32-Bit MCU, 768KB Flash | Renesas

The Renesas R5F72167FAUSH2A is a 32-bit SuperH RISC microcomputer from the SH7216 Group, integrating a high-performance SH-2A core with rich on-chip peripherals and 768 KB of flash memory in a lead-free LQFP package. The part operates at up to 200 MHz and is positioned for embedded motor control, industrial automation, and automotive body/chassis applications where deterministic real-time response is required. A 32-bit SuperH RISC microcontroller is a member of the Reduced Instruction Set Computer (RISC) family that executes most instructions in a single cycle. SuperH (SH) architecture from Renesas combines a compact 16-bit fixed-length instruction encoding with 32-bit internal registers, delivering high code density and deterministic interrupt latency. The SH-2A core adds DSP extensions, a hardware multiplier, and a Harvard bus for simultaneous instruction and data fetches, occupying the middle of Renesas's MCU taxonomy between the 8-bit RL78 and high-end RZ/A ARM Cortex-A application processors. Key features of the R5F72167FAUSH2A include 768 KB on-chip flash, 48 KB on-chip SRAM, a 16-bit timer array (MTU2 and CMT), a 12-bit A/D converter with up to 8 channels, CAN, SCI, and I2C bus interfaces, and an operating voltage range of 3.0 V to 3.6 V. The device supports -40 C to +85 C ambient operation and offers a hardware multiplier plus multiply-accumulate unit for high-speed signal processing in motor control loops. According to the manufacturer datasheet, the SH7216 Group also includes advanced PWM outputs and encoder interfaces for servo and three-phase inverter control. The R5F72167FAUSH2A uses Renesas's SuperH SH-2A CPU core with a 5-stage pipeline, enabling most instructions to execute in a single clock cycle at the rated 200 MHz internal frequency. On-chip debug and a trace buffer are accessible through a dedicated interface, allowing in-circuit emulation without expensive bond-out parts. The integrated CRC module, watchdog timer, and standby modes (sleep, software standby, and module stop) lower system power and improve functional safety diagnostics. Typical applications include AC servo drives, three-phase inverter control, industrial PLCs, HVAC blower controllers, and automotive ECU body modules. The on-chip 12-bit ADC and multi-function timer pulse units (TPU) make it particularly well suited to Field-Oriented Control (FOC) of brushless DC and permanent-magnet synchronous motors. A wide operating temperature range and CAN bus interface also fit it for under-hood automotive and off-highway vehicle subsystems. When designing with this device, pay close attention to decoupling: place a 0.1 uF ceramic bypass capacitor within 5 mm of each VCC/VSS pair, and add a bulk 10 uF or larger tantalum/ceramic capacitor near the analog supply pin to keep ADC readings clean. Use the on-chip flash programmer interface (single-wire or UART-boot) rather than socketed programming, as LQFP packages are not field-replaceable. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond what the manufacturer datasheet alone provides.

USD $19,85 En stock
R5F72167FPU - SH2A-FPU 32-Bit 200MHz MCU, 1MB Flash | Renesas
R5F72167FPU

R5F72167FPU - SH2A-FPU 32-Bit 200MHz MCU, 1MB Flash | Renesas

The Renesas R5F72167FPU is a SH2A-FPU SuperH SH7216 32-bit RISC microcontroller featuring a 200 MHz CPU core, 1 MB on-chip flash memory, and an integrated floating-point unit, housed in a 176-pin LQFP package. It targets high-performance real-time embedded control with deterministic interrupt response and dedicated motor-control peripherals. Key features include a SuperH SH-2A 32-bit RISC core with built-in FPU for single-precision IEEE 754 floating-point operations, 1 MB (1M x 8) program flash, 32 KB SRAM, and a rich set of on-chip peripherals. The device integrates multiple serial interfaces, a 12-bit ADC, motor-control timers (MTU2), and a hardware multiply/accumulate unit, making it suitable for computationally demanding control loops. The SH-2A architecture belongs to the SuperH family of RISC microcontrollers developed by Hitachi and continued by Renesas. It uses a fixed 16-bit instruction encoding with 32-bit extensions, delivering high code density and deterministic pipeline behaviour. The integrated FPU eliminates the need for software floating-point emulation, allowing real-time DSP-style algorithms to execute within microseconds rather than milliseconds. Typical applications include industrial motor control (servo drives, AC inverter control), factory automation controllers, automotive body and powertrain subsystems, and precision mechatronics such as robotics and CNC machines. The combination of deterministic interrupt latency, hardware FPU, and rich timer peripherals makes it ideal for closed-loop torque and speed regulation. When designing with this device, ensure the firmware stack is built for the SuperH-2A instruction set and uses the Renesas HEW or e2 studio toolchain. The 176-pin LQFP package requires careful PCB layout for the high-speed oscillator traces, and decoupling capacitors should be placed as close as possible to every VCC/VSS pair to handle the core's switching current. This page synthesises distributor pricing, drop-in alternatives, and practical design notes for the R5F72167FPU that complement the official Renesas SH7216 hardware manual.

USD $17,60 En stock
R5F74504KBG - 240MHz SH-4A 32-Bit MCU | Renesas | Embedded
R5F74504KBG

R5F74504KBG - 240MHz SH-4A 32-Bit MCU | Renesas | Embedded

The Renesas Electronics R5F74504KBG is a 32-bit RISC microcontroller built around the high-performance SH-4A CPU core, with a maximum operating frequency of 240 MHz and CPU performance exceeding 432 MIPS. The device supports single- and double-precision floating-point arithmetic and is supplied in a 292-pin FBGA package. These characteristics position it for embedded multimedia, communications, industrial control, and other compute-intensive systems requiring a high-throughput 32-bit architecture. A microcontroller is a programmable system-on-chip that integrates a CPU core, memory, peripherals, and interface functions into one package. The SH-4A belongs to the RISC microcontroller hierarchy and combines a compact instruction set with a high clock rate. For the R5F74504KBG, this architecture supports demanding real-time control tasks while retaining a broad embedded peripheral integration. The verified product information identifies a maximum operating frequency of 240 MHz and performance above 432 MIPS. Single- and double-precision floating-point support accelerates mathematical workloads without requiring a separate numerical processor. This makes the MCU relevant to applications involving signal processing, multimedia data handling, graphics, control loops, and connected embedded equipment. The SH7450 and SH7451 groups share the R5F74504KBG family designation. Renesas positions the SH7450 and SH7451 devices as high-performance RISC microcontrollers. Their floating-point capabilities provide a clear distinction from fixed-point-only controllers, while the 240 MHz operating point supports workloads with demanding instruction throughput. Exact memory configuration, peripheral inventory, electrical limits, and operating-temperature boundaries must be confirmed in the manufacturer datasheet before a design is released. Typical application areas include industrial automation, network-connected embedded control, multimedia terminals, audio and signal processing, consumer equipment, and communications infrastructure. The processor performance is useful where deterministic control and floating-point computation must coexist, although firmware and system-level timing still require careful validation. Design planning should begin with the manufacturer pin assignment, supported memory interfaces, peripheral multiplexing, and clock requirements. Because this is a 292-pin FBGA device, careful PCB escape routing, controlled-impedance design, and adequate via and fanout planning are necessary. This page synthesizes verified family specifications, sourcing links, application guidance, and qualification limits for faster engineering review.

Devis En stock
R5S72690W266FP#V0 - SH7269 32-Bit MCU 266MHz 2.5MB SRAM 256-LQFP | Renesas
R5S72690W266FP#V0

R5S72690W266FP#V0 - SH7269 32-Bit MCU 266MHz 2.5MB SRAM 256-LQFP | Renesas

The Renesas Electronics R5S72690W266FP#V0 is a high-performance 32-bit microcontroller from the SH7268/SH7269 Group that integrates an SH2A-FPU core running at 266 MHz and 2.5 MB of on-chip SRAM in a 256-pin LQFP package. It is designed for industrial-grade applications with an operating temperature range of -20 °C to +85 °C and a single 3.0 V to 3.6 V supply rail. The device is supplied as ROMless, allowing external program memory and supporting large firmware images for graphics-rich embedded systems. A 32-bit microcontroller (MCU) is a single-chip computer that integrates a 32-bit CPU core, RAM, peripherals, and interrupt logic. Within the broader taxonomy, the SH7269 belongs to the SuperH family of RISC microcontrollers -> embedded processor -> microcontroller -> integrated circuit. The SH2A-FPU core extends the original SuperH architecture with an integrated floating-point unit and dual-issue pipeline, delivering a significant performance uplift over earlier SH-2 cores for signal-processing workloads. Key features include 2.5 MB on-chip SRAM (1.7× the capacity of the prior SH7266), an SH2A-FPU 32-bit RISC core with hardware floating-point, and a 266 MHz maximum CPU clock. The 256-LQFP package with 0.8 mm pitch provides 133 I/O ports for ample connectivity, and integrated peripherals include DMA, POR, PWM, and a watchdog timer (WDT). The wide 17 mm × 17 mm body with 0.8 mm pitch supports PCB manufacturing at standard line/space rules. Technically, the SH7269 supports sub-clock (13.33 MHz) and main-oscillator modes for low-power standby and high-performance operation, and it embeds a TFT LCD controller suited for WVGA (800 × 480) displays. Hardware floating-point and dedicated DSP extensions make the core efficient at audio decoding and graphics rendering, while the 2.5 MB SRAM allows full-frame buffering without external memory. Typical applications include industrial human-machine interfaces (HMIs), audio processing equipment, TFT-LCD display controllers, motor control, factory automation controllers, and portable medical instrumentation. The combination of large SRAM and an FPU makes the SH7269 well suited to graphics and signal-processing tasks where external memory access would otherwise bottleneck performance. When designing with this device, allocate board space for the 256-LQFP footprint (17 × 17 mm) and provide a clean 3.3 V rail because the on-chip PLL is sensitive to supply noise. A 5.6 kΩ ±1 % reference resistor is required for USB PHY bias per the SH7268/SH7269 hardware manual. This page synthesizes distributor pricing, drop-in alternatives, and design considerations that go beyond the manufacturer datasheet, giving engineers a consolidated view for sourcing and second-sourcing decisions.

USD $24,00 En stock
R7F7010133AFP#KA4 - RH850/F1L 32-Bit 80MHz MCU 512KB Flash | Renesas
R7F7010133AFP#KA4

R7F7010133AFP#KA4 - RH850/F1L 32-Bit 80MHz MCU 512KB Flash | Renesas

The Renesas R7F7010133AFP#KA4 is a 32-bit automotive microcontroller from the RH850/F1L series built on the RH850G3K core, delivering 80 MHz CPU performance with 512 KB of on-chip Flash and housed in a 64-pin LFQFP (10x10 mm) surface-mount package. It is positioned as a low-pin-count member of the RH850/F1x family targeted at chassis, body, and powertrain-adjacent ECUs where ASIL-B/D functional safety and CAN/LIN connectivity are required. What is an RH850 microcontroller? The RH850 is Renesas' 32-bit automotive RISC architecture designed around a multi-core, lockstep-capable pipeline with tightly coupled ECC-protected SRAM and hardware safety hooks (ECC, MBIST, voltage/clock monitors). It sits in the broader automotive MCU hierarchy as: automotive MCU -> 32-bit MCU -> RH850 family -> RH850/F1L sub-family. The RH850/F1L variant trades higher pin counts and larger Flash for cost-sensitive body and chassis applications. Key features include 512 KB of code Flash, 80 MHz maximum operating frequency, integrated CAN/LIN/UART communication peripherals typical of the F1L series, on-chip debugger support, and AEC-Q100 qualification. The 64-LFQFP (10x10) package offers a 0.5 mm pitch footprint suitable for reflow-compatible automotive PCB assembly. The R7F7010133AFP#KA4 uses the RH850G3K 32-bit RISC core with single-precision FPU support and a tightly coupled instruction/data memory hierarchy. Built on a low-power automotive process, the device integrates multiple analog and digital peripherals including 12-bit ADC, timers, and communication channels directly on-die, reducing external component count and BOM cost in body control modules. Typical applications include automotive body control modules (BCM), door/window/seat controllers, HVAC climate control, instrument cluster sub-MCUs, lighting ECUs, and small sensor-hub nodes in zonal architectures. The RH850/F1L is commonly co-deployed with a higher-pin-count F1K/F1M device for communication gateway or domain controller roles. When designing with this part, plan for an RH850-specific toolchain (Green Hills MULTI, IAR EW for RH850, or Renesas CS+) and the E1/E20/E2 emulator for debug. Verify pinout against the specific F1L datasheet revision because the F1L family has multiple Flash/RAM variants sharing the same 64-LFQFP outline. This page synthesizes verified distributor stock, parametric compatibility data, and practical design considerations for engineers evaluating the R7F7010133AFP#KA4 as a drop-in part or a fresh design selection.

USD $5,40 En stock
R7F7010283AFE#KA4 - RH850/F1L 32-Bit MCU, 768KB Flash, 144-LFQFP | Renesas
R7F7010283AFE#KA4

R7F7010283AFE#KA4 - RH850/F1L 32-Bit MCU, 768KB Flash, 144-LFQFP | Renesas

The Renesas R7F7010283AFE#KA4 is a 32-bit microcontroller from the RH850/F1L family built around the RH850G3K core, delivering 768 KB of embedded flash and packaged in a 144-pin LFQFP. The part is qualified for automotive chassis and body applications, supporting single-core operation up to 80 MHz with automotive-grade peripherals including CAN, LIN, and timer units optimized for motor control. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash/RAM), and programmable peripherals onto one silicon die. Within the broader semiconductor taxonomy, an MCU belongs to the embedded microcontroller family, which sits under microcontrollers -> microprocessors -> logic ICs -> integrated circuits -> semiconductors. The RH850/F1L series further specializes in automotive real-time control, offering lockstep cores, ECC flash, and functional-safety documentation for ASIL-B/D systems. Key features of this part include 768 KB code flash, 80 MHz maximum operating frequency, on-chip CAN/LIN/UART/SPI/I2C interfaces, 12-bit ADC, and a wide operating voltage range. The 144-LFQFP package exposes a generous pin count for parallel sensor acquisition and PWM outputs, which is essential for chassis domain controllers and integrated cockpit modules. ECC on flash and RAM supports ISO 26262 functional-safety targets. The RH850G3K core uses a 32-bit RISC architecture with hardware multiply/divide and a tightly coupled interrupt controller for deterministic low-latency response. Automotive peripherals include a Multi-Function Timer Pulse Unit (MTU-V7), A/D converter with scan-group support, and a hardware crypto accelerator on selected derivatives. Compared with generic Cortex-M parts, the RH850/F1L offers superior EMC tolerance and AEC-Q100 Grade 1/2 qualification. Typical applications include automotive body control modules (BCM), chassis ECUs such as ABS/ESC, electric power steering (EPS), and HVAC controllers. The integrated CAN FD interface and large pin count also suit gateway ECUs and zone architectures in modern vehicles. Designers value this part for its ASIL software library, hardware safety manual, and long-term automotive supply stability. Design consideration: at 80 MHz and full peripheral activity, supply current can reach tens of milliamperes; decoupling the four VDD/VSS pairs with 100 nF X7R ceramics within 3 mm of each pin pair is required. A 4.7 µF bulk cap on each analog/digital supply rail is recommended to suppress MCU-injected noise on ADC results. This page synthesizes distributor stock data, same-family RH850/F1L drop-in alternatives, and practical chassis-ECU design notes not bundled in the manufacturer datasheet, giving engineers a faster path to BOM selection and PCB bring-up.

USD $9,95 En stock
R7F7010323AFP - 32-bit 80MHz 768KB Flash Automotive MCU | Renesas
R7F7010323AFP

R7F7010323AFP - 32-bit 80MHz 768KB Flash Automotive MCU | Renesas

The Renesas R7F7010323AFP is a 32-bit RH850G3K RH850/F1L automotive microcontroller built around a 80MHz CPU core with 768KB of embedded flash memory and packaged in a 176-pin LFQFP (24x24 mm). It targets in-vehicle body applications with on-chip peripherals designed for CAN/LIN communication, motor control and sensor interfacing. An automotive microcontroller (MCU) is a ruggedized 32-bit microprocessor with tightly integrated flash, RAM, analog peripherals and communication interfaces qualified for the -40C to +125C automotive temperature range. The RH850 family uses a Harvard-style V850-derived core with multi-layer AHB bus, dedicated hardware for functional safety (ECC on flash/SRAM, lockstep, watchdog) and timers tuned for automotive PWM and capture. Within the broader hierarchy, the R7F7010323AFP sits at MCU -> microcontroller -> embedded processor -> semiconductor. Key features include 768KB program flash, 80MHz maximum CPU clock, integrated CAN/LIN/UART peripherals, multi-channel 12-bit ADCs, programmable timer arrays and hardware CRC. Memory protection, error correction code and a window watchdog support ISO 26262 functional safety integration. The 176-pin LFQFP package provides sufficient I/O count (typically >120 GPIO pins) and excellent thermal performance for body domain ECUs. Technical depth: the RH850G3K core uses a 32-bit RISC architecture with single-cycle multiply, hardware divide and tightly-coupled interrupt controller. The flash macro supports background programming and ECC single-bit correction with double-bit detection. The peripheral bus is split across AHB-Lite and APB bridges to balance DMA and CPU access latency. Power management integrates a low-power timer, standby RAM retention and multiple run/idle/stop modes for quiescent current reduction when the vehicle bus is asleep. Typical applications include body control modules, HVAC door-zone controllers, lighting ECUs, instrument clusters and gateway nodes where CAN-FD connectivity and ASIL-B functional safety are required. The on-chip motor timer/PWM blocks also support small BLDC and brushed-DC loads such as seat or mirror actuators. When designing with this part, plan the flash programming sequence against the 80MHz instruction budget and verify LIN/CAN transceivers separately. ECC initialization must be run before first code execution and the watchdog serviced in the locked window to remain ASIL-B compliant. This page synthesizes distributor pricing, same-family drop-in variants and practical design notes not found in the manufacturer datasheet.

USD $12,75 En stock
R7F7010323AFP#AA3 - 32-Bit 80MHz RH850/F1L 768KB MCU | Renesas
R7F7010323AFP#AA3

R7F7010323AFP#AA3 - 32-Bit 80MHz RH850/F1L 768KB MCU | Renesas

The Renesas R7F7010323AFP#AA3 is a 32-bit automotive microcontroller from the RH850/F1L product line, part of Renesas' RH850/F1x series designed specifically for in-vehicle body applications. The device is built on the RH850G3K core, executes instructions at up to 80 MHz, integrates 768 KB of on-chip Flash memory (768K x 8 organization), and is housed in a 176-pin LFQFP package measuring 24 x 24 mm. It targets automotive body electronic control units that demand high functional safety, real-time responsiveness, and robust electromagnetic compatibility. A microcontroller (MCU) is a single-chip computer containing a CPU, RAM, non-volatile program memory, and a rich set of peripherals such as timers, ADCs, communication controllers, and GPIO. The RH850 family extends this concept with a 32-bit RISC architecture, on-chip hardware safety mechanisms, and an ecosystem tuned for ASIL-D-capable automotive systems. Within that family, the F1L sub-series is the cost- and feature-optimized derivative for body applications such as body control modules, BCMs, HVAC controllers, lighting ECUs, door modules, and instrument clusters. It scales between 256 KB and 2 MB of Flash and comes in 48- to 176-pin packages, positioning F1L between the simpler F1K and the more feature-rich F1M/F1H/F1S variants. Key features of the R7F7010323AFP#AA3 include the RH850G3K core with hardware multiply/divide and DSP-style extensions, single-power-supply operation, on-chip debug and trace via the Renesas E1/E20 emulator, and a comprehensive motor-control timer (MTU3) plus GTM-compatible peripherals depending on sub-line. The device integrates multiple CAN and LIN/UART channels typical of body-domain networking, a 12-bit ADC with up to roughly two dozen channels, and a hardware security module with lock-bit Flash protection. Its 80 MHz core clock is supported by hardware CRC, ECC on critical memories, and self-diagnostic libraries. The R7F7010323AFP#AA3 is offered in the automotive-grade AEC-Q100 qualified temperature range, with ECC on SRAM and Flash to satisfy ASIL-B and, with software libraries, ASIL-D target systems. The 176-LFQFP package provides ample GPIO count for body-control functions with one or more LIN and CAN networks. Designers migrating from older RH850/F1x devices can preserve software compatibility while taking advantage of the larger 768 KB Flash region. Typical applications include body control modules, HVAC control units, automotive lighting ECUs, instrument clusters, and gateway/mid-end body-domain controllers. The combination of 80 MHz performance, 768 KB code space, and the F1L peripheral set makes the part well suited for OEM-grade body applications that require deterministic real-time response and long-term automotive reliability. When developing with this MCU, allocate the Flash budget such that bootloader, application code, and calibration data fit within 768 KB while leaving room for A/B swap or OTA staging. Use the hardware ECC features together with Renesas self-test libraries to satisfy ASIL targets. Lock-bit and access window protection should be enabled before locking the device for production.

USD $10,85 En stock