ISO1450BDWR vs ISO1430DWR Comparaison
Comparaison détaillée côte à côte de ISO1450BDWR par Texas Instruments et ISO1430DWR par Texas Instruments. Comparez les spécifications clés, les paramètres électriques, le conditionnement, le statut de cycle de vie, les prix et la disponibilité pour déterminer le meilleur composant pour vos exigences de conception.
Texas Instruments
ISO1450BDWR - 50Mbps 5kVrms Isolated RS-485/RS-422 Transceiver | Texas Instruments
ISO1450BDWR ✓ ActifComparaison des spécifications
| Paramètre | ISO1450BDWR | ISO1430DWR |
|---|---|---|
| Marque | Texas Instruments | Texas Instruments |
| Catégorie | Interface ICs | Interface ICs |
| Statut du cycle de vie | Actif | Actif |
| Fonction | Isolated half-duplex RS-485 / RS-422 transceiver | — |
| Data Rate (max) | 50 Mbps | — |
| Isolation Voltage (rms) | 5 kVrms (reinforced) | — |
| Number of Drivers / Receivers | 1/1 | — |
| Duplex | Half | — |
| Receiver Hysteresis | [DATA_NEEDED: receiver hysteresis voltage] | — |
| Supply Voltage VCC1 (logic side) | 3 V to 5.5 V | — |
| Supply Voltage VCC2 (bus side) | Internally generated by isolated DC-DC | — |
| Bus Pin ESD (IEC 61000-4-2) | ±16 kV (air / contact, per datasheet) | — |
| Bus Pin ESD (HBM) | ±4 kV | — |
| IEC 61000-4-4 EFT Immunity | ±4 kV | — |
| Surge Immunity | [DATA_NEEDED: IEC 61000-4-5 surge rating] | — |
| Unit Load | 1/8 (up to 256 nodes on bus) | — |
| Common-Mode Range | Wide common-mode bus voltage range (per datasheet) | — |
| Arrêt thermique | Yes | — |
| Current Limiting | Yes | — |
| Low-Power Standby | Yes | — |
| Température de fonctionnement | -40C to +125C | — |
| Boîtier | SOIC-16 wide-body (DW), 16 pins | 16-pin SOIC (DW) |
| Type de montage | Surface Mount | Surface mount |
| Niveau MSL | 3 (per JEDEC J-STD-020) | — |
| Statut RoHS | Compliant | [DATA_NEEDED: RoHS status] |
| Compliance Standards | TIA/EIA-485-A, TIA/EIA-422, IEC 61000-4-2, IEC 61000-4-4 | — |
| Product Type | — | Galvanically isolated half-duplex RS-485 and RS-422 transceiver |
| Maximum Data Rate | — | 12 Mbps |
| Isolation Rating | — | 5 kVrms |
| Transceiver Configuration | — | 1 transmitter and 1 receiver |
| Duplex Mode | — | Half-duplex |
| EMC Protection | — | Protected against ESD and EFT bus events |
| Interface Standards | — | TIA/EIA RS-485 and RS-422 |
| Plage de température de fonctionnement | — | -40°C to +125°C |
| Logic Supply Voltage | — | [DATA_NEEDED: logic-side supply voltage] |
| Bus-side Supply Voltage | — | [DATA_NEEDED: bus-side supply voltage] |
| Propagation Delay | — | [DATA_NEEDED: propagation delay] |
| Receiver Sensitivity | — | [DATA_NEEDED: receiver sensitivity] |
| Common-Mode Transient Immunity | — | [DATA_NEEDED: common-mode transient immunity] |
| ESD Protection Rating | — | [DATA_NEEDED: ESD protection rating] |
| EFT Protection Rating | — | [DATA_NEEDED: EFT protection rating] |
| Isolation Capacitance | — | [DATA_NEEDED: isolation capacitance] |
| Lead Finish | — | [DATA_NEEDED: lead finish] |
| REACH Status | — | [DATA_NEEDED: REACH status] |