MAX3483ESA+ vs SN65HVD37D Comparaison
Comparaison détaillée côte à côte de MAX3483ESA+ par Maxim Integrated et SN65HVD37D par Texas Instruments. Comparez les spécifications clés, les paramètres électriques, le conditionnement, le statut de cycle de vie, les prix et la disponibilité pour déterminer le meilleur composant pour vos exigences de conception.
Texas Instruments
SN65HVD37D - 3.3V Full-Duplex RS-485 Transceiver | TI (Tape & Reel)
SN65HVD37D ✓ ActifComparaison des spécifications
| Paramètre | MAX3483ESA+ | SN65HVD37D |
|---|---|---|
| Marque | Maxim Integrated | Texas Instruments |
| Catégorie | Interface ICs | Interface ICs |
| Statut du cycle de vie | Actif | Actif |
| Product Type | RS-485/RS-422 transceiver | — |
| Tension d'alimentation | 3.3 V | — |
| Verified Supply Range | 3 V to 3.6 V | — |
| Maximum Data Rate | 10 Mbps | — |
| Driver and Receiver Count | 1 driver and 1 receiver | — |
| Duplex Mode | Half-duplex | — |
| Interface Standards | RS-485 and RS-422 | — |
| Driver Architecture | Slew-rate limited | — |
| EMI Control | Slew-rate limitation reduces EMI and reflections | — |
| Low-Speed Error-Free Transmission | Up to 250 kbps | — |
| Power Architecture | 3.3V-powered, low-power transceiver | — |
| Boîtier | 8-SOIC | 14-SOIC (D), 0.154" / 3.90 mm width |
| Type de montage | Surface mount | Surface Mount |
| Operating Voltage | 3 V to 3.6 V | — |
| ESD Protection | [DATA_NEEDED: ESD protection rating for MAX3483ESA+] | — |
| Plage de température de fonctionnement | [DATA_NEEDED: operating temperature range] | — |
| Courant d'alimentation | [DATA_NEEDED: supply current] | — |
| Receiver Output Type | [DATA_NEEDED: receiver output type] | — |
| Termination Requirement | [DATA_NEEDED: termination and biasing details] | — |
| Statut RoHS | [DATA_NEEDED: RoHS status] | — |
| REACH Status | [DATA_NEEDED: REACH status] | — |
| AEC-Q100 Qualification | [DATA_NEEDED: AEC-Q100 qualification] | — |
| Lead-Free Status | [DATA_NEEDED: lead-free status] | — |
| Halogen-Free Status | [DATA_NEEDED: halogen-free status] | — |
| Device Type | — | Transceiver (1 driver / 1 receiver) |
| Protocol | — | RS-422, RS-485 |
| Number of Drivers/Receivers | — | 1 / 1 |
| Duplex | — | Full |
| Supply Voltage (VCC) | — | 3 V to 3.6 V (nominal 3.3 V) |
| Signaling Rate | — | Up to 25 Mbps |
| Receiver Unit Load | — | 1/8 unit load (up to 256 nodes) |
| Bus-Pin ESD Protection (HBM) | — | >15 kV HBM |
| Receiver Hysteresis | — | 60 mV (typical) |
| Quiescent Current (active) | — | 1 mA (typical) |
| Standby / Shutdown Current | — | <1 uA (typical) |
| Température de fonctionnement | — | -40 C to +85 C |
| RoHS / Lead-Free | — | RoHS compliant, lead-free (per TI product page) |
| Fail-Safe Receiver | — | Yes (idle/open/short safe) |
| Driver / Receiver Enable | — | Independent DE and RE pins |