MAX3483ESA+ vs SN65HVD37D Karşılaştırma
Ayrıntılı yan yana karşılaştırma MAX3483ESA+ tarafından Maxim Integrated ve SN65HVD37D tarafından Texas InstrumentsAnahtar özellikleri, elektriksel parametreleri, ambalajı, yaşam döngüsü durumu, fiyatlandırma ve mevcudiyeti karşılaştırarak tasarım gereksinimleriniz için en iyi bileşeni belirleyin.
Texas Instruments
SN65HVD37D - 3.3V Full-Duplex RS-485 Transceiver | TI (Tape & Reel)
SN65HVD37D ✓ AktifÖzellik Karşılaştırması
| Parametre | MAX3483ESA+ | SN65HVD37D |
|---|---|---|
| Marka | Maxim Integrated | Texas Instruments |
| Kategori | Interface ICs | Interface ICs |
| Yaşam Döngüsü Durumu | Aktif | Aktif |
| Product Type | RS-485/RS-422 transceiver | — |
| Besleme Gerilimi | 3.3 V | — |
| Verified Supply Range | 3 V to 3.6 V | — |
| Maximum Data Rate | 10 Mbps | — |
| Driver and Receiver Count | 1 driver and 1 receiver | — |
| Duplex Mode | Half-duplex | — |
| Interface Standards | RS-485 and RS-422 | — |
| Driver Architecture | Slew-rate limited | — |
| EMI Control | Slew-rate limitation reduces EMI and reflections | — |
| Low-Speed Error-Free Transmission | Up to 250 kbps | — |
| Power Architecture | 3.3V-powered, low-power transceiver | — |
| Paket | 8-SOIC | 14-SOIC (D), 0.154" / 3.90 mm width |
| Montaj Türü | Surface mount | Surface Mount |
| Operating Voltage | 3 V to 3.6 V | — |
| ESD Protection | [DATA_NEEDED: ESD protection rating for MAX3483ESA+] | — |
| İşletim Sıcaklığı Aralığı | [DATA_NEEDED: operating temperature range] | — |
| Besleme Akımı | [DATA_NEEDED: supply current] | — |
| Receiver Output Type | [DATA_NEEDED: receiver output type] | — |
| Termination Requirement | [DATA_NEEDED: termination and biasing details] | — |
| RoHS Durumu | [DATA_NEEDED: RoHS status] | — |
| REACH Status | [DATA_NEEDED: REACH status] | — |
| AEC-Q100 Qualification | [DATA_NEEDED: AEC-Q100 qualification] | — |
| Lead-Free Status | [DATA_NEEDED: lead-free status] | — |
| Halogen-Free Status | [DATA_NEEDED: halogen-free status] | — |
| Device Type | — | Transceiver (1 driver / 1 receiver) |
| Protocol | — | RS-422, RS-485 |
| Number of Drivers/Receivers | — | 1 / 1 |
| Duplex | — | Full |
| Supply Voltage (VCC) | — | 3 V to 3.6 V (nominal 3.3 V) |
| Signaling Rate | — | Up to 25 Mbps |
| Receiver Unit Load | — | 1/8 unit load (up to 256 nodes) |
| Bus-Pin ESD Protection (HBM) | — | >15 kV HBM |
| Receiver Hysteresis | — | 60 mV (typical) |
| Quiescent Current (active) | — | 1 mA (typical) |
| Standby / Shutdown Current | — | <1 uA (typical) |
| İşletim Sıcaklığı | — | -40 C to +85 C |
| RoHS / Lead-Free | — | RoHS compliant, lead-free (per TI product page) |
| Fail-Safe Receiver | — | Yes (idle/open/short safe) |
| Driver / Receiver Enable | — | Independent DE and RE pins |